Scribd
Upload
135 views3 pages

Lab 9 Default Route

This document describes configuring default static routes on routers to provide connectivity between two networks - 172.16.6.0 and 172.16.5.0. It involves configuring router interfaces, IP addresses for computers, and static routes on routers 1, 0 and 2 with a default route on routers 0 and 2 to reach unknown networks. Configuring the default routes allows ping connectivity between the two networks.

Uploaded by

kamran ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
135 views3 pages

Lab 9 Default Route

This document describes configuring default static routes on routers to provide connectivity between two networks - 172.16.6.0 and 172.16.5.0. It involves configuring router interfaces, IP addresses for computers, and static routes on routers 1, 0 and 2 with a default route on routers 0 and 2 to reach unknown networks. Configuring the default routes allows ping connectivity between the two networks.

Uploaded by

kamran ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Lab 9

Configuring Default Static Route


Learning Objectives:
In this Lab students will learn to configure default static route on Cisco routers to ensure end-
to-end connectivity between PC0 and PC1

Physical Topology:

Background:
Router0 does not have a route to a remote unknown network 172.16.5.0 which is a Router 2
LAN. Router 2 also have no routes back to Router 0 LAN which is 172.16.6.0 Default route will
be configured on Router 0 and Router 2 to access the unknown networks
Step 1: Configuring Router Interfaces

a) Configure Router 0, Router 1 and Router23 as follows


Router 0:
Fe0/0: 172.16.6.1 255.255.255.0
S1/0: 10.1.1.1 255.255.255.0

Router 1:
S1/0: 10.1.1.2 255.255.255.0
S1/1: 192.168.1.1 255.255.255.0

Router 2:
Fe0/0: 172.16.5.1 255.255.255.0
S1/0: 192.168.1.2 255.255.255.0

b) Configure DCE clock rate 64000 on serial interface of Router 0 and Router 2 using the following
command

Router 1#conf t
Router 1(config)#clock rate 64000
Router 1(config)#exit

c) Check the routing table on all routers using “show ip route” command. What routes are
showing up in each router
Router 0 _____________________
Router 1 _____________________
Router 2 _____________________

Step 2: Configure IP address and default Gateway on both computers

PC 0:
IP Address 172.16.6.2
Gateway: 172.16.6.1

PC 1:
IP Address: 172.16.5.2
Gateway: 172.16.5.1

a) Ping PC0 > PC1


b) Are you able to PING? What’s the ping result

Step 3: Configuring Static IP Route on Router 1 to both LAN’s

Router(config)#ip route 172.16.6.0 255.255.255.0 Serial 1/0


Router(config)#ip route 172.16.5.0 255.255.255.0 Serial 1/1

a) Ping PC0 > PC1. Are you able to PING? ______

Step 3: Configuring Default Static Route on Router 0 and Router 2

Router0(config)# ip route 0.0.0.0 0.0.0.0 Serial1/0


Router2(config)# ip route 0.0.0.0 0.0.0.0 Serial1/0

a) PING PC0 > PC1. Are you able to ping? ______


b) Check the routing table and write down the entries for each router
Router 0 _______________
Router 1 _______________
Router 2 _______________

Conclusion:
____________________________________________________________________

____________________________________________________________________

____________________________________________________________________

Learning Outcomes:
____________________________________________________________________

____________________________________________________________________

____________________________________________________________________

You might also like