Scribd
Upload
459 views7 pages

Slam Force Check For Jacket Walkway Member - Ø 700x25: Technip KT India LTD

This document contains calculations to check the slam force and bending moment for four different diameter jacket walkway members. The slam force was calculated using parameters like diameter, thickness, length, yield stress, modulus of elasticity, density of sea water, water surface velocity and wave slam coefficient. The bending moment acting on each member was also calculated. This was compared to the permissible moment based on the section modulus and allowable stress. For all four members, the bending moment was found to be less than the permissible moment, indicating that the members are adequate.

Uploaded by

Sai Sushank
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
459 views7 pages

Slam Force Check For Jacket Walkway Member - Ø 700x25: Technip KT India LTD

This document contains calculations to check the slam force and bending moment for four different diameter jacket walkway members. The slam force was calculated using parameters like diameter, thickness, length, yield stress, modulus of elasticity, density of sea water, water surface velocity and wave slam coefficient. The bending moment acting on each member was also calculated. This was compared to the permissible moment based on the section modulus and allowable stress. For all four members, the bending moment was found to be less than the permissible moment, indicating that the members are adequate.

Uploaded by

Sai Sushank
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 7

Project Document No.

Revision

0812 - HRD PROCESS PLATFORM 00812-200-CN-3621-012 0

TECHNIP KT INDIA LTD.


Issue 0 1 2 3 Page

Date 4/30/2014
Slam Force Check for Jacket Walkway Prepared By YRC
Member - Ø 700x25 Checked By RNB
Approved By RNB

SLAM FORCE CALCULATION


Ref. Dwg. No - 00812-200-DW-3641-15
Diameter = 0.674 m
Thickness = 0.012 m
Length of member = 12 m
Yield Stress = 345 N/mm2
Modulus of elasticity = 210000 N/mm2
Density of sea water = 1.025 MT/m3
Water surface velocity (From Inpace Analysis) = 5.87 m/sec
Acceleration due to gravity = 9.81 m/sec2
Wave Slam Coefficient = 5.5

Slam Force = Cs*ρ*D*u^2 kN/m As per API C2.3.1b12


2g
= 67.99 kN/m

Member Check

Bending Moment acting on member = 1223.8 kN-m {w*l2)/8}

Moment of Inertia = 0.001 m^4

Section Modulus = 0.004 m^3

Allowable Stress = 234 Mpa As per API Clause.3.2.3

Permissible Moment = 1265 kN-m

Hence OK
Project Document No. Revision

0812 - HRD PROCESS PLATFORM 00812-200-CN-3621-012 0

TECHNIP KT INDIA LTD.


Issue 0 1 2 3 Page

Date 4/30/2014
Slam Force Check for Jacket Walkway Prepared By YRC
Member - Ø 600x25 Checked By RNB
Approved By RNB

SLAM FORCE CALCULATION


Ref. Dwg. No - 00812-200-DW-3641-15
Diameter = 0.574 m
Thickness = 0.012 m
Length of member = 5 m
Yield Stress = 345 N/mm2
Modulus of elasticity = 210000 N/mm2
Density of sea water = 1.025 MT/m3
Water surface velocity (From Inpace Analysis) = 5.87 m/sec
Acceleration due to gravity = 9.81 m/sec2
Wave Slam Coefficient = 5.5

Slam Force = Cs*ρ*D*u^2 kN/m As per API C2.3.1b12


2g
= 58.28 kN/m

Member Check

Bending Moment acting on member = 182.1 kN-m {w*l2)/8}

Moment of Inertia = 0.001 m^4

Section Modulus = 0.003 m^3

Allowable Stress = 243 Mpa As per API Clause.3.2.3

Permissible Moment = 707 kN-m

Hence OK
Project Document No. Revision

0812 - HRD PROCESS PLATFORM 00812-200-CN-3621-012 0

TECHNIP KT INDIA LTD.


Issue 0 1 2 3 Page

Date 4/30/2014
Slam Force Check for Jacket Walkway Prepared By YRC
Member - Ø 500x20 Checked By RNB
Approved By RNB

SLAM FORCE CALCULATION


Ref. Dwg. No - 00812-200-DW-3641-15
Diameter = 0.474 m
Thickness = 0.007 m
Length of member = 5 m
Yield Stress = 345 N/mm2
Modulus of elasticity = 210000 N/mm2
Density of sea water = 1.025 MT/m3
Water surface velocity (From Inpace Analysis) = 5.87 m/sec
Acceleration due to gravity = 9.81 m/sec2
Wave Slam Coefficient = 5.5

Slam Force = Cs*ρ*D*u^2 kN/m As per API C2.3.1b12


2g
= 48.56 kN/m

Member Check

Bending Moment acting on member = 151.8 kN-m {w*l2)/8}

Moment of Inertia = 0.000 m^4

Section Modulus = 0.001 m^3

Allowable Stress = 226 Mpa As per API Clause.3.2.3

Permissible Moment = 267 kN-m

Hence OK
Project Document No. Revision

0812 - HRD PROCESS PLATFORM 00812-200-CN-3621-012 0

TECHNIP KT INDIA LTD.


Issue 0 1 2 3 Page

Date 4/30/2014
Slam Force Check for Jacket Walkway Prepared By YRC
Member - Ø 450x22 Checked By RNB
Approved By RNB

SLAM FORCE CALCULATION


Ref. Dwg. No - 00812-200-DW-3641-48
Diameter = 0.424 m
Thickness = 0.009 m
Length of member = 6.3 m
Yield Stress = 345 N/mm2
Modulus of elasticity = 210000 N/mm2
Density of sea water = 1.025 MT/m3
Water surface velocity (From Inpace Analysis) = 5.87 m/sec
Acceleration due to gravity = 9.81 m/sec2
Wave Slam Coefficient = 5.5

Slam Force = Cs*ρ*D*u^2 kN/m As per API C2.3.1b12


2g
= 43.71 kN/m

Member Check

Bending Moment acting on member = 216.8 kN-m {w*l2)/8}

Moment of Inertia = 0.000 m^4

Section Modulus = 0.001 m^3

Allowable Stress = 243 Mpa As per API Clause.3.2.3

Permissible Moment = 290 kN-m

Hence OK
Project Document No. Revision

0812 - HRD PROCESS PLATFORM 00812-200-CN-3621-012 0

TECHNIP KT INDIA LTD.


Issue 0 1 2 3 Page

Date 4/30/2014
Slam Force Check for Jacket Walkway Prepared By YRC
Member - Ø 355.6x19.05 Checked By RNB
B : 6 of 9

Approved By RNB

SLAM FORCE CALCULATION


Ref. Dwg. No - 00812-200-DW-3641-48
Diameter = 0.3296 m
Thickness = 0.00605 m
Length of member = 4.125 m
Yield Stress = 345 N/mm2
Modulus of elasticity = 210000 N/mm2
Density of sea water = 1.025 MT/m3
Water surface velocity (From Inpace Analysis) = 5.87 m/sec
Acceleration due to gravity = 9.81 m/sec2
Wave Slam Coefficient = 5.5

Slam Force = Cs*ρ*D*u^2 kN/m As per API C2.3.1b12


2g
= 34.54 kN/m

Member Check

Bending Moment acting on member = 73.5 kN-m {w*l2)/8}

Moment of Inertia = 0.0001 m^4

Section Modulus = 0.000 m^3

Allowable Stress = 236 Mpa As per API Clause.3.2.3

Permissible Moment = 115 kN-m

Hence OK
Project Document No. Revision

0812 - HRD PROCESS PLATFORM 00812-200-CN-3621-012 0

TECHNIP KT INDIA LTD.


Issue 0 1 2 3 Page

Date 4/30/2014
Slam Force Check for Jacket Walkway Prepared By YRC
Handrail Member - Ø48.3x5.08 Checked By RNB
Approved By RNB

SLAM FORCE CALCULATION


Ref. Dwg. No - 00812-200-DW-3641-48
Diameter = 0.0483 m
Thickness = 0.00508 m
Length of member = 1.519 m
Yield Stress = 316 N/mm2
Modulus of elasticity = 210000 N/mm2
Density of sea water = 1.025 MT/m3
Water surface velocity (From Inpace Analysis) = 3.4 m/sec
Acceleration due to gravity = 9.81 m/sec2
Wave Slam Coefficient = 5.87

Slam Force = Cs*ρ*D*u^2 kN/m As per API C2.3.1b12


2g
= 1.68 kN/m

Member Check

Bending Moment acting on member = 0.5 kN-m {w*l2)/8}

Moment of Inertia = 0.0000 m^4

Section Modulus = 0.000 m^3

Allowable Stress = 237 Mpa As per API Clause.3.2.3

Permissible Moment = 2 kN-m

Hence OK
Project Document No. Revision

0812 - HRD PROCESS PLATFORM 00812-200-CN-3621-012 0

TECHNIP KT INDIA LTD.


Issue 0 1 2 3 Page

Date 4/30/2014
Slam Force Check for Jacket Walkway Prepared By YRC
Handrail Member - Ø60.3x5.54 Checked By RNB
Approved By RNB

SLAM FORCE CALCULATION


Ref. Dwg. No - 00812-200-DW-3641-48
Diameter = 0.0603 m
Thickness = 0.00554 m
Length of member = 3 m
Yield Stress = 316 N/mm2
Modulus of elasticity = 210000 N/mm2
Density of sea water = 1.025 MT/m3
Water surface velocity (From Inpace Analysis) = 3.4 m/sec
Acceleration due to gravity = 9.81 m/sec2
Wave Slam Coefficient = 5.87

Slam Force = Cs*ρ*D*u^2 kN/m As per API C2.3.1b12


2g
= 2.10 kN/m

Member Check

Bending Moment acting on member = 2.4 kN-m {w*l2)/8}

Moment of Inertia = 0.0000 m^4

Section Modulus = 0.000 m^3

Allowable Stress = 237 Mpa As per API Clause.3.2.3

Permissible Moment = 3 kN-m

Hence OK

You might also like