Section 7 Electrical System: Group 1 Component Location

SECTION 7 ELECTRICAL SYSTEM
GROUP 1 COMPONENT LOCATION
4 5
3
6
1
20
7
19
15
13
14
16 8
9
18
10
11
17
HYD FILTER
12
20B7EL02
1 Combination switch 8 Back up alarm 15 High horn

2 Display 9 Steering sensor 16 Pump motor
3 Working lamp switch(opt) 10 Traction controller 17 Fuse box assy
4 Beacon switch(opt) 11 Relay 18 Drive motor
5 DC-DC converter 12 Flasher unit assy 19 Accelerator assy
6 Beacon lamp(opt) 13 Fan assy 20 Parking micro switch
7 Pump controller 14 Contactor
7-1
GROUP 2 ELECTRICAL CIRCUIT (without OPSS)
(15BT-7 : -#0034, 18BT-7 : -#0041, 20BT-7 : -#0021 / 16B-7 : -#0005, 18B-7 : -#0004, 20B-7 : -#0008)
FUSE BOX ASSY
2
F4 F6 F7 F8 F9 F10 F11 F12

10A 15A 10A 10A 10A 10A 10A 10A
20 HEAD 25 26 27 29 55 55A 52A

24A LAMP 52
24 BRAKE
SWITCH 02C B FLAS 29E 29B
LAMP C- E -HER
KO 44 SWITCH 29C 29D 29A
L UNIT
LAMP 41
21B 22 40 59A 47A
RELAY T/S
INPUT OUTPUT 40A REV
S/W LAMP
S/W
KEY 02D 42A
4 59 47
S/W C- 46A
42 45 49 49A FAN FAN1 FAN2
DC-DC 45A
21 CONVERTER
4B 4B 4A 4C M M M TNR
46B 46A 59B 47B
49B
46
GND GND
(IN) (OUT)
LH RH TAIL STOP T/S B/U TAIL STOP T/S B/U T/S HORN TNR REAR
T/S LAMP BEA LAMP
02A WORK
LAMP LAMP BACKUP -S/W CON -S/W
COMBI. COMBI. LAMP LAMP
LAMP LAMP -LH -RH BUZZER
00A 02M -LH 02H -RH 02L 02N 02N 02E 02G 02B 02S 02T 02F 02J 02P 02L 02Q
02N
KO B- C-
LINE
CONTACTOR
TRACTION PUMP
INVERTER INVERTER
10W 300 DUAL AC-2 AC-2 PUMP
MOTOR
TRACTION TIB+ 21D 21D PIB+
US KEY C3 KO KO F1 KEY U
MOTOR-LH
M VS SEAT S/W V M
350A 92 122 222 300A
WS SEAT C5 E4 COMMON W
EMERGENCY
SWITCH FWD S/W LIFT S/W
196 90 122D 222A 60 296
C35 (PTHERM_L) FORWARD C6 E5 LIFT ENABLE (PTHERM) F6
PARKING TILT S/W

195 99 122B 61 295
C34 (NTHERM_L) PARKING C10 E6 1st SPEED (NTHERM) F12
TEMP SENSOR TEMP SENSOR
ACCEL. S/W AUX1 S/W
194 95 122C 62 294
C11 (PENC_L) ENABLE C8 F10 2nd SPEED (ENC VCC) D1
REV S/W AUX2 S/W
192 91 122D 63 292
C12 (NENC_L) REVERSE C7 E7 3rd SPEED (ENC GND) D2
BRAKE S/W
B+ 193 98 122D 222A 293
C22 (PHA_L) BRAKE C9 E13 SR (ENC A) D3
191 122A 04 291

C23 (PHB_L) COMMON C4 F11 -BATT (ENC B) D5
TRACTION 120 04 64
MOTOR-RH UM PLC C27 F5 SAFETY PPOT E2
LIFT
M VM LC COIL KO POTENTIOMETER
01 05 65
WM NLC C26 B1 -BATT CPOT E1
21C
396 94 ACCELERATOR
GRAPHIC SMART DISPLAY 05 03
C25 (PTHERM_R) CPOT C21 B2 MODE NPOT E3
PEDAL 00B 21A
B- A1 -BATT KEY A6 KO
395 07
BATTERY C24 (NTHERM_R) NPOT C20
36/48V TEMP SENSOR 00B
A2 -BATT
394 93
C1 (PENC_R) PPOTST C16
326A
B3 CAN-T
392 96 STEER 226
C2 (NENC_R) CPOTST C17 SENSOR C4 CAN_H OUT
CAN-H CAN-L
393 06 A3 A4
C13 (PHA_R) NPOTST C15 120?
326 325
391 326 225
C14 (PHB_R) CAN_H OUT A7 C2 CAN_L OUT
325
CAN_L OUT A4
126 126
CAN_H A1 C3 CAN_H
125 125
CAN_L A6 C1 CAN_L
TIB- TIB-
20B7EL01
B-
7-2
ELECTRICAL CIRCUIT (with OPSS)
(15BT-7 : #0035-, 18BT-7 : #0042-, 20BT-7 : #0022- / 16B-7 : #0006-, 18B-7 : #0005-, 20B-7 : #0009-)
FUSE BOX ASSY

2
F4 F6 F7 F8 F9 F10 F11 F12

10A 15A 10A 10A 10A 10A 10A 10A
20 HEAD 25 26 27 29 55 55A 52A

24A LAMP 52
24 BRAKE
SWITCH 02C B FLAS 29E 29B
LAMP C- E -HER
KO 44 SWITCH 29C 29D 29A
L UNIT
LAMP 41
21B 22 40 59A 47A
RELAY T/S
INPUT OUTPUT 40A REV
S/W LAMP
S/W
KEY 02D 42A
4 59 47
S/W C- 46A
42 45 49 49A FAN FAN1 FAN2
DC-DC 45A
21 CONVERTER
4B 4B 4A 4C M M M TNR
46B 46A 59B 47B
49B
46
GND GND
(IN) (OUT)
LH RH TAIL STOP T/S B/U TAIL STOP T/S B/U T/S HORN TNR REAR
T/S LAMP BEA LAMP
02A WORK
LAMP LAMP BACKUP -S/W CON -S/W
COMBI. COMBI. LAMP LAMP
LAMP LAMP -LH -RH BUZZER
00A 02M -LH 02H -RH 02L 02N 02N 02E 02G 02B 02S 02T 02F 02J 02P 02L 02Q
02N
KO B- C-
LINE
CONTACTOR
TRACTION PUMP
INVERTER INVERTER
10W 300 DUAL AC-2 AC-2 PUMP
MOTOR
TRACTION TIB+ 21D 21D PIB+
US KEY C3 KO KO F1 KEY U
MOTOR-LH
M VS SEAT S/W V M
350A 92 122 222 300A
WS SEAT C5 E4 COMMON W
EMERGENCY
SWITCH FWD S/W LIFT S/W
196 90 122D 222A 60 296
C35 (PTHERM_L) FORWARD C6 E5 LIFT ENABLE (PTHERM) F6
PARKING TILT S/W

195 99 122B 61 295
C34 (NTHERM_L) PARKING C10 E6 1st SPEED (NTHERM) F12
TEMP SENSOR TEMP SENSOR
ACCEL. S/W AUX1 S/W
194 95 122C 62 294
C11 (PENC_L) ENABLE C8 F10 2nd SPEED (ENC VCC) D1
REV S/W AUX2 S/W
192 91 122D 63 292
C12 (NENC_L) REVERSE C7 E7 3rd SPEED (ENC GND) D2
BRAKE S/W
B+ 193 98 122D 222A 293
C22 (PHA_L) BRAKE C9 E13 SR (ENC A) D3
191 122A 04 291

C23 (PHB_L) COMMON C4 F11 -BATT (ENC B) D5
TRACTION 120 04 64
MOTOR-RH UM PLC C27 F5 SAFETY PPOT E2
LIFT
M VM LC COIL KO POTENTIOMETER
01 05 65
WM NLC C26 B1 -BATT CPOT E1
21C
396 94 ACCELERATOR
GRAPHIC SMART DISPLAY 05 03
C25 (PTHERM_R) CPOT C21 B2 MODE NPOT E3
PEDAL 00B 21A
B- A1 -BATT KEY A6 KO
395 07 221 1
BATTERY C24 (NTHERM_R) NPOT C20 PHYDRO F3
36/48V TEMP SENSOR 00B
A2 -BATT MCV SOL.
394 93 08
C1 (PENC_R) PPOTST C16 NHYDRO F9
326A
B3 CAN-T
392 96 STEER 226
C2 (NENC_R) CPOTST C17 SENSOR C4 CAN_H OUT
CAN-H CAN-L
393 06 A3 A4
C13 (PHA_R) NPOTST C15 120?
326 325
391 326 225
C14 (PHB_R) CAN_H OUT A7 C2 CAN_L OUT
325
CAN_L OUT A4
126 126
CAN_H A1 C3 CAN_H
125 125
CAN_L A6 C1 CAN_L
TIB- TIB-
20B7EL01S
B-
7-2-1
GROUP 3 ELECTRIC COMPONENTS
1. FUNCTIONS OF BATTERY FORKLIFT TRUCK AND ELECTRIC COMPONENTS.

The major functions of forklift truck can be divided into DRIVING FUNCTION and LOADING &
UNLOADING FUNCTION.
All the components that work DRIVING and LOADING & UNLOADING functions are driven by AC
MOTORS. And as the BATTERY works as power source of these motors, a charging device is
needed.
To drive the fork lift truck, a DRIVING CONTROL SYSTEM and some electric components such as
direction change lever(forward/reverse section switch) and accelerator are required to select the
driving direction and to control the speed of driving motor.
The CONTROL SYSTEM includes some protective circuits that protect the equipment and
components from malfunctioning.
A MONITORING SYSTEM is installed in the monitor panel, which monitors the equipment and
working condition, and let the operator take proper action. For the monitoring system, there are many
sensors such as current sensors, hydraulic pressure sensors, and temperature sensors. The
HYUNDAI Battery forklift trucks are equipped with the most advanced DRIVING CONTROL SYSTEM
currently available world-widely. The operator friendliness features enable him to set the truck
conditions properly according to each working circumstance easily on his seat, and the SELF-
DIAGNOSTIC function displays current status of truck in working.
7-3
2. BATTERY
1) STRUCTURE
3 1
Protective tube
6 5
8
7,9,10,11
20B7EL03
1 Cells 7 Plug
2 Steel box 8 Spacer
3 Cell connector 9 Handle (Red)
4 Row connector 10 Screw
5 Positive leading cable 11 Spring washer
6 Negative leading cable
7-4
2) GENERAL
As in the battery forklift, the battery is an
energy source, the handling of the battery
is very important. The life and performan-
ce of the battery greatly depend on the
ordinary handling and maintenance.
Therefore, be sure to check and maintain
the battery so that it may be kept best.
20B7EL04
3) SPECIFICATION AND SERVICE DATA
Item Unit 15BT-7/16B-7 18/20BT-7, 18/20B-7

Type VCI 505 VCI 585
Rated voltage V 48
Capacity AH/hr 505/5 585/5
Electrolyte WET
Dimension(WÝDÝH) mm 990Ý545Ý635 990Ý630Ý635
Connector SB350
Weight(Max/Min) kg 980/710 1140/835
Fully charged specific gravity 1.280(25ÁC)

End of discharge specific gravity 1.130(25ÁC)
Discharge end voltage 48V(option 36V)
Electrolyte Refined dilute sulfuric
Replenishment fluid Refined water(pure water)
Insulation resistance More than 1Mɮ
7-5
4) SAFETY PRECAUTIONS
(1) When a sulfuric acid contact with skin
For acid contact with skin, eye or clothing, flush with water immediately. If swallowed, drink a large
amount of water or milk. Seek medical attention immediately. When handling acid, always wear
eye goggles or a face shield and rubber gloves.
(2) Strict prohibition of fire and ventilation
Since batteries generate explosive hydrogen gas, no fire should be drawn near. Before the battery
charging, keep the battery cover open and check the ventilation status. Charging in an enclosed
space can cause a explosion.
(3) Never place metallic articles on the batteries
If done so, it may cause “short circuit” accidents(dangerous especially while charging).
Sparks will be generated which is equally dangerous as open fires.
(4) Handling of charger
When connecting or disconnecting a battery from a charger or attempting maintenance, make
sure switches are all off. Ensure that the charger and the battery are matched. If a 300Ah battery
is used with a charger designed to charge a 500Ah battery, it will severely overcharge the battery.
5) OPERATION PRECAUTIONS
(1) Avoid over-discharge
If over-discharged, it will be difficult to restore the batteries to the original state by recharge. In
order to maintain the batteries in use for long period of time, it is recommended to use the
batteries with discharge amount not exceeding 80% of the rated capacity. Further care should be
taken for preventing the unit cell voltage from falling below 1.5V.
(2) Avoid over-charge
If overcharged, the rise in battery temperature will become excessive, resulting in deterioration of
plates and other parts and markedly shortening of battery life.
(3) Avoid excessive elevation of temperature
Be sure to open the cover of battery housing tray before charging. If there is a possibility of
temperature to exceed 55ÁC, discontinue the charge operation temporarily, or reduce the charge
current.
6) INSTRUCTION
(1) Unpacking
Electric traction storage batteries(herein after refer to as “batteries”) are delivered to customers in
dry-charged condition. At unpacking, check whether the batteries and accessories have been
damaged. If there are observed defects, you should notify the condition to our branch office or
agent. Never remove the sealing plug until the battery is put into service.
7-6
(2) Performance and maintenance of batteries
Η Initial charge
Wet-charged battery gradually decrease its capacity during storage. In order to provide sufficient
discharge capacity in the first discharge, the good initial charge is required. The conditions of
initial charging are seen as below at room temperature.
a. By modified constant voltage charger
Connect the battery to the charger and turn on the equalizing charge “ON”. The battery will be
fully charged and terminated automatically.
b. By constant voltage constant current charger
Connect the battery to the charger and turn on the equalizing charge “ON”. The battery will be
fully charged and terminated automatically.
c. By constant current charger
Connect the charger to the battery and charge the battery by 0.1CÝ5 hour rate nominal
capacity current for 24 hours or more. The charge shall be terminated when one of the following
condition is identified.
ÂWhen a constant value is indicated for more than 1 hour after the battery voltage has reached
the maximum value.
ÂWhen more than 1 hour of charge is continued after the electrolyte specific gravity has risen
fully and becomes constant.
Θ Discharge and capacity
The capacity of batteries is indicated at 5 hour rate capacity which means the battery can be
discharged for 5 hours with the discharge current calculated by dividing the capacity value by 5
until the unit cell mean voltage reaches down to 1.7V at the electrolyte temperature of 30ÁC.
That is, the capacity is indicated by AH(ampere hour) being calculated as the product of
ampere(A) and time(H). However, even in the same type of batteries, the capacity varies with the
discharge conditions(discharge current, battery temperature and specific gravity of electrolyte)
Even if the batteries discharged its full capacity, if immediately charged to full, there will be no
harmful effects remained. Ideal charging amount(AH) is 110-125% of the amount of previous
discharge.
Ι Specific gravity of electrolyte
Specific gravity of electrolyte drops at discharge and rises at charge. When the batteries are fully
charged, it becomes almost constant and shows no further rise. The specific gravity value varies
with the change in temperature. Therefore specific gravity measurement should be made with
temperature of electrolyte at the same so the measured specific gravity value could be corrected
to that at the standard temperature of 25Á C by the following formula.
S25 = St + 0.0007(t-25)
Where, S25 : Specific gravity at 25Á
C
St : Actually measured specific gravity at t Á
C
t : Electrolyte temperature (ÁC)
The standard specific gravity for this type of battery is 1.280Ü0.01(25Á C) at full charge condition.
If the electrolyte is decreased naturally while using, distilled water shall be replenished up to the
specified level. (Never refill sulfuric acid)
Only when large quantity of electrolyte is lost due to spillage, etc., dilute sulfuric acid specified in
gravity shall be added.
7-7
Κ Normal charge
Charge the discharged batteries as quickly as possible. The temperature of electrolyte before
starting the charging operation shall preferably be below 45Á C, and the temperature during the
charge should be maintained at no higher than 55Á C. (Under any unavoidable situations, it should
never be above 55Á C). Methods of charging varies in precise meaning with the types of chargers
used. A standard charging method is described hereunder. (If a special method is mentioned to
be adopted, follow that instruction).
a. Charging by modified constant voltage automatic charger
There is almost automatic charger today which complete the charging just only connecting the
plug between battery and charger without outer operating timer but if your charger has it, after
setting the timer for 3-4 hours and turn on the charger and the charger is left as it is, then the
charge will be made automatically. In principle, regardless of the amount of previous discharge,
it is not required to alter the setting of timer time. The recommendable current value of this type
of charger is “5 hour rate current Ý1.0~1.5” at the start of charging, and at the final stage it is “5
hour rate current Ý0.15~0.25”. Normally the charge is terminated within 8~12 hours
automatically.
b. Charging by constant current constant voltage automatic charger
After a lapse of specified charging time after the switch is turned on, the charge will be
completed by turning off the switch. The charging time can be calculated by the following
formula.
Amount of previous discharge(AH)
Charging time = + 2~3(H)
Capacity of charger(A)
When the amount of previous discharge is not known, use the 5 hour rate rated capacity of the
batteries. At immediately after charging, the charge current is allowed up to 3 times 5 hour rate
current. For charger provided with a timer, the charge will terminate automatically if the timer is
set at the specified time according to the operation manual.
Λ Equalizing charge
When large number of cells are used in a set of battery, the voltage and specific gravity of
respective cells tend to become unequal, resulting in necessity of charging all the cells at an
appropriate time in order to equalize them. This is called equalizing charge. Normally the
equalizing charge should be carried out once every month. The methods are in normal type
charger, extend the charge for 5 more hours after full charge at the final stage current, and in
automatic charger which are in most cases provided with timer, extend the time setting for 3-6
more hours.
Μ Water replenishment
Only the water content of electrolyte is decreased due to electrolysis of water during charge and
natural evaporation. If a battery used with the electrolyte decreased excessively, plates will
deteriorate resulting in markedly shortening of battery life. Be sure to check the electrolyte level
once every week. If the electrolyte level is lowered, replenish distilled water up to the specified
level. In this case, never attempt to replenish sulfuric acid or tap water. Use only distilled water
for battery replenishment. If the amount of water required for weekly addition to a unit cell for
100AH of battery capacity is in excess of 45cc, it is assumed that the cell is receiving overcharge.
Accordingly, be sure to reduce slightly the daily charge amount. Under the normal conditions, the
addition of water per week is 45cc or less. Incidentally, water replenishment should be made
before charging to the contend of minimum level.
7-8
(for the purpose of uniform stirring of electrolyte by charging). If the electrolyte level is improper
after completion of charging, you may topping up the electrolyte level to the maximum level .
a. Determination of replenishment time and methods(cell with ONE TOUCH CAP)
Confirm the electrolyte level by looking at the float in the ONE TOUCH CAP. If too low as shown
in figure, replenish water. Replenishment shall be performed after opening the cover of the plug
using syringe and jug. When refilling is completed, close each cover completely until “click”
sound is heard.
Minimum Level Maximum Level
Cell cover
Cell cover
Float Float
B153EL041 B153EL042
Ν Cleaning
If electrolyte spills or the cells are polluted with dust or stains, it will cause generation of leak
current. Wipe off dust and stains with moist cloth and clean in such a manner that the cells are
kept in dry condition. In the case of plastic containers or covers, never use such organic solvents
as paint thinner and gasoline. If used, the plastic containers or covers may suffer cracking. If you
are forced to use them, be sure to use white kerosene.
Ξ Notice on charging
The charging area must be well ventilated to facilitate exhaust of gas generated from the battery
during charging. Charge the battery in an area free from iron working, welding, etc. Further the
battery generates hydrogen, oxygen, acid mist and on rare occasions, hydrogen sulfide during
charging depending on the case. Special care may be required in the case of equipment and
objects near the battery that may contaminated or damaged. Do not pull out the charging plug
during charging, as it will cause sparks. Since hydrogen gas generated during charging may
remain in the area surrounding the battery after charging, never bring fire or flame close to this
area. In case of counter-balance type vehicles, open the battery cover before charging.
Ο Repair of failure cell
a. To remove a cell from the circuit or battery from steel tray, it is first necessary that the intercell
connector be removed.
b. Before performing any repairs, you must open one-touch caps for gas purging of all cells. After
you have finished that, must remove connector covers and on-touch caps from failure cell
including surrounding cells. All vent holes of cells removed of one-touch caps must cover by
four layers of water dampened cloth and then proceed with repairs. Using an acid syringe
withdraw sufficient electrolyte from failure cell to reduce the liquid levels until minimum level
indicating of one touch caps.
c. The safe and most efficient method of removing a connector is with hand or electric drill(͚25mm)
from failure cell as well as all surrounding cells.
7-9
You must make sure to clear of explosive hydrogen gas in the cells before repairs. Be
careful not to drill to far into the cell and damage the unit. During drilling operation make
sure lead curls produced do not contact opposite cell poles and cause a spark.
d. Upon completion of drilling the intercell connectors, can be lifted off.
e. Lifted off the failure cell from circuit after removing of intercell connector.
f. Installing new cell and connector.
g. With surfaces properly cleaned and neutralized, position the connectors.
h. Place damp rags around each lead head. Hold tip of the welder in center of post move welder
completely around top of post and out to the area where the post meets the connector. Move
welder back to center of post and add molten lead until area is filled to top of connector. Again,
move welder completely around area, with tip on molten lead. If you have jig for welding
connector, have easier and better welding work.
i. When replacing electrolyte in a repaired cell, use sulphuric acid of the same specific gravity that
is found in the balance of the battery.
j. Finally, rejoin connector covers and one-touch caps to the cells.
Π Summary of daily maintenance
a. Avoid overcharge. After discharge, charge the batteries immediately. The standard frequency
of equalizing charge is more than once every month.
b. Check the electrolyte level once a week. If found decreased, replenish distilled water up to the
specified level.
c. The top surface of battery cells should be kept clean and dry.
d. Be sure to keep open the cover of battery housing tray during charge.
e. Never draw near open fires such as lighted cigarettes or burning matches during charge.
(3) Others
Η Storage of batteries
When batteries are stored, keep them distant from room heaters or other heat generating
sources. Clean, cool and dry place where no direct sunlight is directed is suited for battery
storage. Before putting into storage, it is important to charge the batteries and keep the
electrolyte level at the specified level. When the temperature in storage location is higher than
20ÁC, check the specific gravity once a month, and when lower than 20Á C, check it once every
two months. If the measurements show values lower than 1.230(20Á C), it is required to charge
the battery in accordance with the method described in NORMAL CHARGE.
Θ Maintenance record
It is recommended to keep maintenance record in order to know the operational conditions of
batteries. Daily charge and discharge, equalizing charge requirements, and water replenishment
requirements can be clarified at a glance. Measurements of specific gravity and temperatures
once every two to four months after equalizing charge and maintenance thereof will serve for
battery health diagnosis.
Ι Electrolyte temperature
The operating temperature range of batteries is -10~45Á C(temperature of electrolyte). If the
batteries are exposed to cold atmosphere in discharged condition, the electrolyte may freeze, and in
extreme cases, the capacity will be decreased, but, if not frozen, no adverse effects will be exerted
over the life. Contrarily if the temperature is high, especially if used at above 55Á
C, the battery life
will be considerably shortened. Care must be taken so that the temperature during charge will be
maintained at 55Á C or lower. Even under unavoidable circumstances it should not exceed 55Á C.
7-10
7) TROUBLESHOOTING
Nature of trouble Symptoms Causes Repair

Deformation ÂDeformation of container, ÂExcessive temperature ris- ÂReplace
lid or one touch cap ing or external impact
Breakage ÂElectrolyte leakage acco- ÂExternal impact, improper ÂReplace or install a new
rding to breakage of cont- handling, excessive vibrat- one
ainer, lid or one touch cap ion
ÂTermination of connector ÂExcessive temperature ÂReplace
or pole post etc. rising or vibration/external
impact
Sulfate ÂSpecific gravity drops and ÂWhen left in state of disch- ÂNeed equalizing charge
capacity is decreased. arge or left long without
equalizing charge.
ÂCharge voltage rises rapi- ÂInsufficient charge. ÂNeed equalizing charge
dly with immature gassing ÂWhen electrolyte is so de- ÂNeed equalizing charge
in earlier stage but specific creased that plate is de-
gravity does not rise and posed.
charge can’t be carried ÂWhen concentration of ÂAdjust specific gravity
out. electrolyte rises.
ÂWhen impurities are mixed ÂReplace electrolyte
in electrolyte.
Decrease and ÂMay be easily detected by ÂRise of temperature due to ÂReplace
falling of specific measurement of the spec- such trouble.
gravity ific gravity. ÂWhen left long period with- ÂRefill water in regular per-
out refilling of water. iod
ÂShort circuit. ÂReplace
Rise of specific ÂMay be easily detected by ÂDiluted sulfuric acid is ÂAdjust specific gravity after
gravity measurement of the spec- used in refilling. full charge.
ific gravity. ÂWhen the electrolyte level ÂRefill distilled water.
excessively drops.
Mixing of impurities ÂDecrease of capacity. ÂMetals such as iron, copper, ÂUnder a fully discharged
nickel and manganese. condition, pour out the
ÂDrop of charge and disch- ÂImpurities such as sea electrolyte. Then pour in
arge voltage. water, chloric acid, nitric an acid of the specific
acid etc. gravity higher by 0.03~0.05
ÂOdor of generated gas and ÂFilling of impure water. than that of the drained
coloring of the electrolyte. acid. Charge fully and
adjust the specific gravity to
the specified value.
7-11
3. DRIVE MOTOR
1) STRUCTURE
900
950
951
952
953
300 220 226 224 223 222 225

520
523
524
345
400
330
717
500
505
710
506
320
335
51 700 515
Max torque : 2.04kgf.m
(14.8lbf.ft)
20B7EL07
51 Stator 335 Circlip 700 Rotor

220 Terminal 345 O-ring 710 Circlip
222 Hexagon screw 400 Plate 717 Woodruff key
223 Hexagon nut 500 Sensor bearing 900 Plug
224 Disk 505 Wavy washer 950 Amp pin
225 Hexagon nut 506 O-ring 951 Amp plug
226 Disk 515 Cylinder screw 952 Wire seal
300 Drive end cover 520 Temp sensor 953 Amp seal
320 Ball bearing 523 Tube
330 Sealing ring 524 Amp pin
7-12
2) SPECIFICATION
Item Unit Specification
Type - TSA200-100-63
Rated voltage V 32
Rated output kW 4.4
Insulation - Class F
3) MAINTENANCE INSTRUCTION
ö Before starting the maintenance please disconnect the power supply.
(1) Ball bearing
Both ball bearing are maintenance free. Should it be necessary to remove the bearings in case of
repair, they should be replaced. In any case the sealing parts (shaft sealing ring etc.) have to be
replaced.
If a bearing which is to be replaced has only one sealing lip, this should be greased with quality
bearing grease.
After approximately 10,000 operating hours the bearings have to be replaced.
(2) Disassembly and assembly
The motor is assembled and disassembled according to the relevant sectional drawing and part
list. (See page 7-12)
7-13
4. PUMP MOTOR
1) STRUCTURE
900
950
951
225 952
953
240 223 224 221 222 220
520
523
51 524
400
506
500
327
505
320
300 700 515
20B7EL16
51 Stator 320 Ball bearing 524 Amp pin

220 Terminal 327 Shaft seal 700 Rotor
221 Cylinder screw 400 Commutator end plate 900 Plug
222 Hexagon screw 500 Sensor bearing 950 Amp pin
223 Hexagon nut 505 Wavy washer 951 Keying plug
224 Disk 506 O-ring 952 Wire seal
225 Hexagon nut 515 Cylinder bolt 953 Interface seal
240 Terminal base 520 Temp sensor
300 Drive end cover 523 Tube
7-14
2) SPECIFICATION
Type - TSA170-210-009
Rated voltage V 30
Rated output kW 15.8
Insulation - Class F
3) INTERNAL INVOLUTE SPLINE DATA
Flat root side fit - Class 7

No of teeth EA 9
Spline pitch mm 16/32
Pressure angle Degree 30
Major diameter mm 16.535
Form diameter mm 15.977
Minor diameter mm 12.9286
Pin diameter mm 2.743
Measurement over 2 pins mm 10.251 / -0.1
4) MAINTENANCE INSTRUCTION
ö Before starting the maintenance please disconnect the power supply.
(1) Ball bearing
Both ball bearing are maintenance free. Should it be necessary to remove the bearings in case of
repair, they should be replaced. In any case the sealing parts (shaft sealing ring etc.) have to be
replaced.
If a bearing which is to be replaced has only one sealing lip, this should be greased with quality
bearing grease.
After approximately 10,000 operating hours the bearings have to be replaced.
(2) Disassembly and assembly
The motor is assembled and disassembled according to the relevant sectional drawing and part
list. (See page 7-14)
7-15
5. CONTROLLER SYSTEM
1) STRUCTURE
Traction controller Pump controller

20B7EL10
(1) Specifications
Model Model Application Type Power Current limit
15/18/20BT-7 DUAL AC2 Traction AC 36-48V, 330A+330A 330A / 3min

16/18/20B-7 AC2 Pump AC 36-48V, 450A 450A / 3min
7-16
2) OPERATIONAL FEATURES
(1) Features
⯱ Speed control.
⯲ Optimum behavior an a slope due to the speed feedback:
♼The motors speed follows the accelerator, starting a regenerative braking if the speed overtakes
the speed set-point.
♼The system can perform an electrical stop on a ramp (the machine is electrically hold on a
slope) for a programmable time.
⯳ Electronic differential feature with torque balance between external and internal wheel.
⯴ Regenerative release braking based upon deceleration ramps.
⯵ Regenerative braking when the accelerator pedal is partially released (deceleration).
⯶ Direction inversion with regenerative braking based upon deceleration ramp.
⯷ Regenerative braking and direction inversion without contactors: only the main contactor is
present.
⯸ Optimum sensitivity at low speeds.
⯹ Voltage boost at the start and with overload to obtain more torque (with current control).
⯺ Hydraulic steering function:
♼The traction inverter sends a "hydraulic steering function" request to the pump inverter on the
can-bus line.
⯻ Backing forward and reverse options are available, with the tune and the speed of the function
programmable with Zapi console or buttons on a display.
⯼ High efficiency of motor and battery due to high frequency commutations.
⯽ Modification of parameters through the programming console or buttons on a display.
⯾ Internal hour-meter with values that can be displayed on the console.
⯿ Memory of the last five alarms with relative hour-meter and temperature displayed on the console.
⬼ Diagnostic function with Zapi console for checking main parameters.
⬽ Built in BDI feature.
⬾ Flash memory, software downloadable via serial link and via CANBUS.
(2) Diagnosis
The microcontrollers continually monitor the inverter and carry out a diagnostic procedure on the
main functions. The diagnosis is made in 4 points.
⯱ Diagnosis on key switch closing that checks: watchdog circuit, current sensor, capacitor charging,
phase's voltages, contactor drivers, can-bus interface, if the switch sequence for operation is
correct and if the output of accelerator unit is correct, correct synchronization of the two ⦼CS,
integrity of safety related inputs hardware.
⯲ Standby diagnosis in standby that checks: Watchdog circuit, phase's voltages, contactor driver,
current sensor, can-bus interface.
⯳ Diagnosis during operation that checks: Watchdog circuits, contactor driver, current sensors, can-
bus interface.
⯴ Continuous diagnosis that checks: Temperature of the inverter, motor temperature.
Diagnosis is provided in two ways. The digital console can be used, which gives a detailed
information about the failure; the failure code is also sent on the Can-Bus.
7-17
3) DESCRIPTION OF THE CONNECTORS
(1) Traction controller
1 12 1 3
13 23 4 5
24 35 8 1 6 8
CONN C CONN B CONN A
20B7EL13
7-18
No. of Pin Function Description
A1 CAN_H High level CANBUS.
A2 CANT_H CANBUS termination output, 120 ohm internally connected to CAN_H.
Connect to CAN_L_OUT to insert the termination.
A3 CAN_POS Positive of CAN circuit; to be used in case of optoisolated CANBUS.
A4 CAN_L_OUT Low level CANBUS: to be used as repetition for CAN_L line or to be
connected to CANT_H to insert termination resistance.
A5 CANT_L CANBUS termination output, 120 ohm internally connected to CAN_L.
Connect to CAN_H_OUT to insert the termination.
A6 CAN_L Low level CANBUS.
A7 CAN_H_OUT High level CANBUS: to be used as repetition for CAN_ H line or to be
connected to CANT_L to insert termination resistance.
A8 CAN_NEG Negative of CAN circuit, to be used in case of optoisolated CANBUS.
B1 PCLRXD Positive serial reception.
B2 NCLRXD Negative serial reception.
B3 PCLTXD Positive serial transmission.
B4 NCLTXD Negative serial transmission.
B5 GND Negative console power supply.
B6 +12 Positive console power supply.
B7 FLASH
B8 FLASH
C1 PENC_R Positive of right motor encoder power supply (+5 V/+12 V).
C2 NENC_R Negative of right motor encoder power supply.
C3 KEY Connected to + batt trough a microswitch and a 10 A fuse in series.
C4 CM Common of FW / REV / HB / PB / SEAT / ENABLE / SR / EX. HYDRO /
BACKING microswitches.
C5 SEAT Seat presence signal; active high.
C6 FORWARD Forward direction request signal; active high.
C7 REVERSE Reverse direction request signal; active high.
C8 ENABLE/BACK. Traction or backing request signal; active high.
C9 PB Pedal brake request signal; active high.
C10 SR/HB/EX. HYDRO Speed reduction signal or hand brake or exclusive hydro input; active low
(microswitch open). See also page 7-24.
C11 PENC_L Positive of left motor encoder power supply (+5 V/+12 V).
C12 NENC_L Negative of left motor encoder power supply.
C13 PHA_R Right motor encoder phase A.
C14 PHB_R Right motor encoder phase B.
C15 NPOTST Negative of steering potentiometer (-BATT).
C16 PPOTST Positive of steering potentiometer (+5 V/+12 V).
C17 CPOTST Steering potentiometer wiper signal.
C18 CPOTB Brake potentiometer wiper signal.
7-19
No. of Pin Function Description
C19 NPOTB -BATT.
C20 NPOT Negative of traction accelerator potentiometer, tested for wire is connec-
tion diagnosis.
C21 CPOT Traction potentiometer wiper signal.
C22 PHA_L Left motor encoder phase A.
C23 PHB_L Left motor encoder phase B.
C24 NTHERM_R Negative of right traction motor temperature sensor.
C25 PTHERM_R Right traction motor temperature signal.
C26 NLC Output of main contactor coil driver (drives to -BATT).
C27 PLC Positive of main contactor coil.
C28 NBRAKE Output of electric brake coil; drives the load to -BATT, maximum current 3 A.
C29 PBRAKE Positive of the electromechanical brake coil.
C30 PAUX Positive of auxiliary load.
C31 NAUX Output of auxiliary load driver (drives to -BATT).
C32 -BATT
C33 PPOT Traction/brake potentiometer positive, 5/10 V output; use load > 1 kohm.
C34 NTHERM_L Negative of left traction motor temperature sensor.
C35 PTHERM_L Left traction motor temperature signal.
7-20
Encoder installation
Η Traction controller card is fit for different types of encoder. To control AC motor with Zapi inverter, it
is necessary to install an incremental encoder with 2 phases shifted of 90Á. The encoder power
supply can be +5 or +12V. It can have different electronic output.
C11/C1 : +5V/+12V : Positive of encoder power supply.
C12/C2 : GND : Negative of encoder power supply.
C22/C13 : A : Phase A of encoder.
C23/C14 : B : Phase B of encoder.
Θ Connection of encoder with open collector output; +5V power supply.
20B7EL25
Ι Connection of encoder with open collector output; +12V power supply.
20B7EL26
The encoder power supply voltage and output electronic has to be communicated to ZAPI in
order to correctly set the selection jumpers in the logic card.
7-21
(2) Pump controller
+BATT +BATT
Before Fuse
AC-2 INVERTER Voltage -BATT

Registration Label Label
U V W
1
7 1
F A
8
8 1
B 1
E C 3
D 1 4
20B7EL14
No. of pin Function Description

A1 PCLRXD Positive serial reception.
A2 NCLRXD Negative serial reception.
A3 PCLTXD Positive serial transmission.
A4 NCLTXD Negative serial transmission.
A5 GND Negative console power supply.
A6 +12 Positive console power supply.
A7 FLASH Must be connected to A8 for the flash memory programming (if used).
A8 FLASH Must be connected to A7 for the flash memory programming (if used).
B1 -BATT -Batt.
B2 MODE This input allows the customer to select the software in case of double
version.
C1 CAN-L Low level CAN-BUS voltage I/O.
C2 CAN-L-OUT Low level CAN-BUS voltage I/O.
C3 CAN-H High level CAN-BUS voltage I/O.
C4 CAN-H-OUT High level CAN-BUS voltage I/O.
7-22
No. of pin Function Description
D1 D6 Incremental ENCODER connector.
E1 CPOT Accelerator potentiometer wiper.
E2 PPOT Potentiometer positive: 10V output; keep load > 1KW.
E3 NPOT Negative of accelerator unit, tested for wire disconnection diagnosis.
E4 CM Common of LIFT ENABLE / 1st SPEED / 2nd SPEED / 3rd SPEED / 4th
SPEED / HYDRO / SR microswitches.
E5 LIFT ENABLE Input for potentiometer lifting enable input; it is active HIGH.
E6 1st SPEED Input for first speed request; it is active HIGH.
E7 3rd SPEED Input for third speed request; it is active HIGH.
E8 AN. IN. Rotary encoder analog input.
E9 PPOT Potentiometer positive: 10V output; keep load > 1KW.
E10 -BATT -Batt.
E11 -BATT -Batt.
E12 HYDRO REQ. Input for hydraulic steering request. Active high.
E13 SR Speed reduction input. Active low (switch opened).
E14 DIG. IN. This is a digital input, free for customer request.
F1 KEY Connected to the power supply through a microswitch (CH) with a 10A
fuse in series.
F2 PMC Positive of the auxiliary output.
F3 PHYDRO Positive for MCV solenoid (OPSS valve, lock valve).
F4 4th SPEED Input for fourth speed request; it is active HIGH.
F5 SAFETY If not connected to -batt the MC coil power output will be disabled. Can
also be used as a general purpose input.
F6 PTHERM Input for motor temperature sensor.
F7 CM Common of LIFT ENABLE / 1st SPEED / 2nd SPEED / 3rd SPEED / 4th
SPEED / HYDRO / SR microswitches.
F8 NMC This output can be used for drive the main contactor coil (single pump
configuration) or to drive an auxiliary load (combi configuration)
F9 NHYDRO Negative for MCV solenoid (OPSS valve, lock valve).
F10 2nd SPEED Input for second speed request; it is active HIGH.
F11 GND -Batt.
F12 NTHERM -Batt.
7-23
4) FUNCTION CONFIGURATION
ÿ TRACTION CONTROLLER-MASTER
Using the CONFIG MENU of the programming console, the user can configure the following
functions (see "OPERATIONAL FEATURE" chapter for an explanation of "hydraulic steering
function") :
(1) Submenu "SET OPTIONS"
Η Hour counter
- RUNNING : The counter registers travel time only.
- KEY ON : The counter registers when the "key" switch is closed.
Θ Battery check
- ON : The battery discharge level check is carried out; when the battery level reaches 10%, an
alarm is signalled and the maximum current is reduced to the half of the programmed
value.
- OFF : The battery discharge level check is carried out but no alarm is signalled.
Ι Traction cutout
When the alarm "BATTERY LOW" appears, if this option is programmed to ON the traction
maximum speed is reduced to 60Hz.
Κ Lift cutout
When the alarm "BATTERY LOW" appears, if this option is programmed to ON the lift function is
disabled.
Λ S.R.O.
If this option is set to on the static return to off is requested for starting the truck. The required
sequence is :
ÂSeat-direction lever-accelerator pedal or :
ÂSeat-accelerator pedal-direction lever within the seq. delay time
If this option is set to off the required sequence to start the truck is :
ÂDirection lever-accelerator pedal or :
ÂAccelerator pedal-direction lever within the seq. delay time
Μ Hydro key on
- ON / OFF : If this option is programmed ON the traction inverter manages an hydraulic steering
function when the "key" is switched ON.
Ν Stop on ramp
- ON : The stop on ramp feature (truck electrically hold on a ramp) is managed for a fixed time (6
sec.).
- OFF: The stop on ramp feature is not performed.
Ξ Aux input #1
- EXCLUSIVE HYDRO : Input C10 activates hydraulic steering function, output A31 is activated.
- OPTION #1 : Input C10 is the input for an handbrake device, active low (open switch).
- OPTION #2 : Input C10 is the input for a speed reduction device, active low (open switch).
Ο Pedal braking
- DIGITAL : The truck does not have a potentiometer installed on the mechanical brake pedal, but
only a switch; when the accelerator pedal is released and the brake pedal is pushed
(brake switch closed), the inverter performs an electrical braking following "Pedal
braking" parameter.
7-24
Π Set temperature
- DIGITAL : A digital (ON/OFF) motor thermal sensor is connected to C25 (C35) input.
- ANALOG : An analog motor thermal sensor is connected to C25 (C35) (the curve can be
customized on a customer request).
- NONE : No motor thermal sensor switch is connected.
Ρ Steer table
This parameter is used to set the correct steering table.
- OPTION #1 : The steering table is the one for 3 wheels truck.
- OPTION #2 : The steering table is the one for 4 wheels truck.
΢ Display
If this option is set to on the communication with the Zapi graphic display is enabled.
Σ Pedal type
- OPTION #1 : The pedal position is sent to the display for graphic indication.
- OPTION #2 : The speed set-point is sent to the display for graphic indication.
Τ Pedal brake stop
If set to on the truck is stopped when the pedal brake is pressed.
If set to off the traction current is reduced to the half of the maximum current.
(2) Submenu "ADJUSTMENTS"
Η Set pot brake min
It records the minimum value of braking pedal potentiometer when the braking pedal switch is
closed; the procedure is similar to the "Program Vacc" function (see page 7-37). This procedure
must be carried out only if the "Pedal braking" option is programmed as "Analog".
Θ Set pot brake max
It records the maximum value of braking pedal potentiometer when the braking pedal is fully
pressed; the procedure is similar to the "Program Vacc" function (see page 7-37). This procedure
must be carried out only if the "Pedal braking" option is programmed as "Analog".
Ι Set battery type
It selects the nominal battery voltage.
Κ Adjust battery
Fine adjustment of the battery voltage measured by the controller.
Λ Max steer right
This is the function to record in the controller EEPROM the steering poti output voltage when the
wheels are fully turned right (maximum of the steering poti range).
Μ Max steer left
wheels are fully turned left (minimum of the steering poti range).
Ν Set steer 0-pos.
wheels are straight.
Ξ Set steer right
This parameter sets the max steering angle in right direction.
Ο Set steer left
This parameter sets the max steering angle in left direction.
7-25
⯺ Throttle O zone
It establishes a deadband in the accelerator input curve (see also curve below).
⯻ Throttle X point
This parameter changes the characteristic of the accelerator input curve.
⯼ Throttle Y point
This parameter changes the characteristic of the accelerator input curve.
20B7EL17
VACC MIN and VACC MAX are values programmable by the "Program Vacc" function.
⯽ Adjustment #2 bdi
It adjusts the lower level of the battery discharge table.
⯾ Adjustment #1 bdi
It adjusts the upper level of the battery discharge table.
⯿ Adjustment #03 :
Set an increment of battery charge above actual value. If battery voltage exceed this total value
the software recognize charging, and battery charge percentage increase to correct value also if
battery isn't fully charged.
⬼ Main cont. voltage
This parameters adjusts the line contactor coil voltage (PWM output C26).
⬽ Aux output voltage
This parameters adjusts the electric brake coil voltage (PWM output C28).
⬾ Adjustment #04 :
This parameter determines the motor temperature level at which the "Motor temperature" alarm is
signalled. This parameter must be adjusted only if the "Set temperature" (menu "Set option")
parameter is programmed "Analog".
⬿ Speed factor
It adjusts the speed coefficient to have the correct speed indication on the display. This coefficient
has to be regulated depending on truck mechanic characteristics. It results from the following
formula :
Speed factor = 88 * rr * p / ⮴
where:
rr = total gearbox ratio
⮴= traction wheel diameter (cm)
P = number of pair poles of the motor
7-26
ÿ TRACTION CONTROLLER-SLAVE
Using the config menu of the programming console, the user can configure the following functions.
Not available.
Η Set battery type
It selects the nominal battery voltage.
Θ Adjust battery
Fine adjustment of the battery voltage measured by the controller.
Ι Aux output voltage
This parameter adjusts the voltage of the auxiliary output coil, PWM output A31.
ÿ PUMP CONTROLLER
Using the config menu of the programming console, the user can configure the following functions.
Η Hour counter
RUNNING : The counter registers travel time only.
KEY ON : The counter registers when the "key" switch is closed.
Θ Set temperature
DIGITAL : A digital (ON/OFF) motor thermal sensor is connected to F6 input.
ANALOG : An analog motor thermal sensor is connected to F6 (the curve can be customized on
a customer request).
NONE : No motor thermal sensor switch is connected.
Ι Joystick
OFF : The truck model includes mechanical lever distributor (default)
ON : The truck model includes electro-hydraulic distributor and finger tips. Can communication
with Can tiller and Hydro CB zapi modules is enabled.
Κ Digital lift
OFF : The lift sensor includes a lift switch and an analogue lift sensor. Lift speed can be controlled
proportionally with lever position.
ON : The lift sensor includes a lift switch only. Lift speed cannot be controlled proportionally.
7-27
Η Set battery type : Selects the nominal battery voltage.
Θ Adjust battery : Fine adjustment of the battery voltage measured by the controller.
Ι Throttle O zone : Establishes a deadband in the accelerator input curve (see also curve below).
Κ Throttle X zone : This parameter changes the characteristic of the accelerator input curve.
Λ Throttle Y zone : This parameter changes the characteristic of the accelerator input curve.
20B7EL17
VACC MIN and VACC MAX are values programmable by the "PROGRAM VACC" function.
Μ Adjustment #04 : This parameter determines the motor temperature level at which the "MOTOR
TEMPERATURE" alarm is signalled. This parameter must be adjusted only if
the "SET TEMPERATURE" (menu "SET OPTION") parameter is programmed
"ANALOG"
Ν Pwm on main contactor : It sets the PWM level in % on the output F8, here spare.
Ξ Pwm on aux output : It sets the PWM level in % on the output F8, here used to drive a lower
locking valve. This output is driven when the seat switch is closed on
traction controller.
Ο MC/AUX PWM : It sets the PWM level in % on the outputs F8 and F9. Here is used to drive a
lower locking valve.
Π Min lift : Volts. It sets the minimum value for the lift sensor.
Ρ Max lift : Volts. It sets the maximum value for the lift sensor.
΢ Min lower : Volts. It sets the minimum value for the lowering sensor. It has to be adjusted only in
case the joystick option is set to on.
Σ Max lower : Volts. It sets the maximum value for the lowering sensor. It has to be adjusted only in
Τ Min tilt up : Volts. It sets the minimum value for the lowering sensor. It has to be adjusted only in
Υ Max tilt up : Volts. It sets the maximum value for the lowering sensor. It has to be adjusted only in
7-28
5) PROGRAMMING & ADJUSTMENTS
There are two ways to adjust parameter via a console or buttons on a display.
ö Adjustments via buttons on a display, please refer to the display section. (page 7-44)
ADJUSTMENTS VIA CONSOLE (Option)
Adjustment of parameters and changes to the inverter's configuration are made using the digital
console. The console is connected to the "B" connector of the inverter.
(1) Descriptions of console
Inverter B
connector
Console connector
Display
Buttons
20B7EL15
ö Digital consoles used to communicate with AC inverter controllers must be fitted with EPROM CK
ULTRA, minimum "Release number 3.02".
7-29
(2) Description of standard console menu
Η Traction controller-Master
20B7EL18
7-30
Θ Traction controller-Slave
20B7EL19
7-31
Ι Pump controller
20B7EL20
7-32
Κ Display
20B7EL27
7-33
(3) Description of the console save function
The SAVE function allows the operator to transmit the parameter values and configuration data of
the chopper into the console memory. It is possible to load 64 different programmers.
The information saved in the console memory can then be reloaded into another chopper using
the RESTORE function.
The data that is available via the SAVE function is as follows:
- All parameter values (Parameter change).
- Options (Set. options).
Flow chart showing how to use the SAVE function of the digital console.
Η Opening Zapi display.
Θ Press ENTER to go into the general menu.
Ι The display will show:
Κ Press ROLL UP or ROLL DOWN button until

SAVE PARAM. appear on the display.
Λ The display shows:
Μ Press ENTER to go into the SAVE function.
Ν If this facility has been used before the type of

chopper data stored appears on the top main
with a 2 digit reference.
Ξ Keep pressing either ROLL UP or ROLL DOWN
keys until the second Main indicates a FREE
storage facility.
Ο Press ENTER to commence SAVE routine.
Π You can see the items that are being stored

whilst the SAVE routine is happening.
Ρ When finished, the console shows :
΢ Press OUT to return to the opening Zapi display.
20B7EL21
7-34
(4) Description of the console restore function
The RESTORE PARAM function allows transfer of the console's stored data into the memory of
the chopper. This is achieved in a fast and easy way using the method previously used with the
SAVE PARAM. function.
The data that is available via the RESTORE PARAM. function is as follows :
- All Parameter Values (Parameter change).
- Options (Set options)
When the RESTORE operation is made, all data in the chopper memory will be written over
and replace with data being restored.
Flow chart showing how to use the RESTORE function of the digital console.

SAVE PARAM. appear on the display.
Μ Press ENTER to go into the RESTORE PARAM

function.
Ν The display shows the type of model stored, with
a code number.
Ξ Keep pressing either ROLL UP or ROLL DOWN

keys until the desired model appears on the
display.
Ο Press ENTER to commence restore operation.
Π The display asks "ARE YOU SURE?".
Ρ You can see the items that are being stored in

the chopper memory whilst the RESTORE
routine is happening
΢ When finished, the console shows :
Σ Press OUT to return to the opening Zapi display.
20B7EL22
7-35
(5) Description of alarms menu
The microprocessor in the controller records the last five alarms that have occurred. Items
remembered relative to each alarm are: the code of the alarm, the number of times the particular
Alarm occurred, the hour meter count, and the inverter temperature.
This function permits a deeper diagnosis of problems as the recent history can now be accessed.
Flow chart showing how to use the ALARMS function via the digital console.

PARAMETER CHANGE. appear on the display.
Μ Press ENTER to go into the ALARMS function.
Ν The display will show the most recent alarm.
Ξ Each press of the ROLL UP button brings up

following alarms. Pressing ROLL DOWN returns
to the most recent.
Ο If an alarm has not occurred, the display will
show: ALARM NULL.
Π When you have finished looking at the alarms,

press OUT to exit the ALARMS menu.
Ρ The display will ask "CLEAR LOGBOOK?".
΢ Press ENTER for yes, or OUT for NO.
Σ Press OUT to return to the opening Zapi display.
20B7EL23
7-36
(6) Description of console program vacc function
This function looks for and remembers the minimum and maximum potentiometer wiper voltage
over the full mechanical range of the pedal. It enables compensation for non symmetry of the
mechanical system between directions.
The operation is performed by operating the pedal after entering the PROGRAM VACC function.
Flow chart showing how to use the PROGRAM VACC function of the digital console:
⯱ Opening Zapi display.
⯲ Press ENTER to go into the general menu.
⯳ The display will show:
⯴ Press ROLL UP or ROLL DOWN button until

PROGRAM VACC. appear on the display.
⯵ The display shows:
⯶ Press ENTER to go into the PROGRAM VACC

routine.
⯷ The display will show the minimum and
maximum values of potentiometer wiper output.
Both directions can be shown.
⯸ Press ENTER to clear these values.
Display will show 0.0.
⯹ Select forward direction, close any interlock
switches that may be in the system.
⯺ Slowly depress the accelerator pedal (or tiller
butterfly) to its maximum value. The new
minimum and maximum voltages will be
displayed on the console plus an arrow
indicating the direction.
⯻ Select the reverse direction and repeat Item10.
⯼ When finished, press OUT.
⯽ The display will ask : "ARE YOU SURE?".
⯾ Press ENTER for yes, or OUT for NO.
⯿ When finished, the console shows:
⬼ Press OUT again to return to the opening Zapi

menu. 20B7EL24
7-37
6) TESTER MENU
(1) Traction controller-Master
The most important input or output signals can be measured in real time using the TESTER
function of the console. The Console acts as a multimeter able to read voltage, current and
temperature. In the following chapter a list of relative measurements for different configurations.
Η Motor voltage
This is the voltage supplied to the motor by the inverter; it is expressed as a percentage of the full
voltage (which depends of the battery voltage).
Θ Frequency
This is the frequency of the voltage and current supplied to the motor.
Ι Encoder
This is the speed of the motor, expressed in the same unit of the frequency; this information
comes from the speed sensor.
Κ Slip value
This is the difference of speed between the rotating field and the shaft of the motor, expressed in
the same unit of the frequency.
Λ Current rms
Root Mean Square value of the motor current.
Μ Temperature
The temperature measured on the aluminum heat sink holding the MOSFET devices.
Ν Temperature #1
This is the temperature of the right motor; if the option is programmed "None" (see page 7-24) it
shows 0Á.
Ξ Temperature #2
This is the temperature of the left motor; if the option is programmed "None" (see page 7-24) it
shows 0Á.
Ο Accelerator
The voltage of the accelerator potentiometer's wiper (CPOT). The voltage level is shown on the
left hand side of the console display and the value in percentage is shown on the right hand side.
Π Steer angle
This is the indication of the angular position of the steered wheel.
Ρ Internal wheel cutback
This is the indication of the speed reduction applied to the internal wheel; in other words, it shows
the ratio of the two speeds.
΢ Forward switch
The level of the forward direction digital input FW.
- ON / +VB = Input active, switch closed.
- OFF / GND = Input non active, switch open.
Σ Backward switch
The level of the reverse direction digital input BW.
Τ Enable switch
The level of the enable digital input:
7-38
⯿ Seat switch
The level of the seat microswitch digital input.
⬼ Cutback switch
The level of the speed reduction microswitch.
- ON / GND = Input active, switch opened.
- OFF / +VB = Input non active, switch closed.
⬽ Brake switch
The level of the pedal brake microswitch.
⬾ Exclusive hydro
Status of the exclusive hydro switch.
⬿ Brake pedal pot.
Voltage of the brake potentiometer's wiper (CPOTB). The parameter is active only if the PEDAL
BRAKING parameter is set ANALOG.
⭀ Hand brake
The level of the handbrake microswitch.
- ON / GND = Input active, switch opened.
- OFF / +VB = Input non active, switch closed.
⭁ Voltage booster
This is the booster of the voltage supplied to the motor in load condition; it is expressed in a
percentage of the full voltage.
⭂ Battery voltage
Level of battery voltage measured at the input of the key switch.
⭃ Battery charge
The percentage Charge level of the battery.
⭄ Speed value
(2) Traction controller-Slave

⯱ Motor voltage
⯲ Frequency
⯳ Encoder
⯴ Slip value
⯵ Current rms
Root mean square value of the motor current.
7-39
Μ Temperature
The temperature measured on the aluminum heat sink holding the MOSFETdevices.
Ν Voltage booster
Ξ Battery voltage
Level of battery voltage measured at the input of the key switch.
Ο Seat switch
The level of the seat microswitch digital input.
- OFF / GND = Input non active, switch opened.
Π Forward switch
The level of the forward direction digital input FW.
Ρ Backward switch
The level of the reverse direction digital input BW.
΢ Enable switch
The level of the enable digital input:
7-40
(3) Pump controller
The most important input or output signals can be measured in real time using the TESTER
function of the console. The console acts as a multimeter able to read voltage, current and
temperature. The following definition listing shows the relative measurements :
Η Motor voltage
Θ Frequency
Ι Encoder
Κ Slip value
Λ Current rms
Root Mean Square value of the motor current.
Μ Temperature
The temperature measured on the aluminum heat sink holding the MOSFET devices.
Ν Motor temperature
This is the temperature of the motor; if the option is programmed "None" it shows 0Á.
Ξ Lifting switch:
Status of the lifting switch.
- ON / +VB = Active entry of closed switch.
- OFF / GND = Non active entry of open switch.
Ο Descent switch:
Status of the lowering speed switch of the pump.
Π Tilt up switch:
Status of the tilt up switch of the pump.
Ρ Tilt down switch:
Status of the tilt down switch of the pump.
΢ Shift lft switch:
Status of the shift left speed switch of the pump.
Σ Shift rgt switch:
Status of the shift right speed switch of the pump.
7-41
⯾ Aux in switch:
Status of the aux in switch of the pump.
⯿ Aux out switch:
Status of the aux out switch of the pump.
⬼ Hydro speed req.:
Status of the hydro speed request of the pump.
⬽ Lift/lower req.:
Level of the lift and lower analogue signal. The voltage is shown on the left hand side of the
Display and the value in percentage on the right hand side.
⬾ Tilt request:
Level of the tilt analogue signal. The voltage is shown on the left hand side of the display and the
value in percentage on the right hand side.
⬿ Shift request:
Level of the shift analogue signal. The voltage is shown on the left hand side of the display and
the value in percentage on the right hand side.
⭀ Aux request:
Level of the auxiliary analogue signal. The voltage is shown on the left hand side of the display
and the value in percentage on the right hand side.
⭁ Cutback switch:
Status of the speed reduction switch.
- ON / GND = Active entry of open switch.
- OFF / +VB = Non active entry of closed switch.
⭂ Voltage booster:
⭃ Battery voltage:
Level of battery voltage measured at the input to the key switch.
7-42
¤ Aux in switch:
Status of the aux in switch of the pump.
¤ıAux out switch:
Status of the aux out switch of the pump.
§ Hydro speed req.:
Status of the hydro speed request of the pump.
§æLift/lower req.:
Level of the lift and lower analogue signal. The voltage is shown on the left hand side of the
Display and the value in percentage on the right hand side.
§ Tilt request:
Level of the tilt analogue signal. The voltage is shown on the left hand side of the display and the
value in percentage on the right hand side.
§ Shift request:
Level of the shift analogue signal. The voltage is shown on the left hand side of the display and
the value in percentage on the right hand side.
§ Aux request:
Level of the auxiliary analogue signal. The voltage is shown on the left hand side of the display
and the value in percentage on the right hand side.
§ıCutback switch:
Status of the speed reduction switch.
- ON / GND = Active entry of open switch.
- OFF / +VB = Non active entry of closed switch.
§ Voltage booster:
§ Battery voltage:
Level of battery voltage measured at the input to the key switch.
7-42
7) GENERAL SUGGESTION FOR SAFETY
For a proper installation take care of the following recommendations:
After operation, even with the key switch open, the internal capacitors may remain charged for
some time. For safe operation, we recommend that the battery is disconnected, and a short circuit
is made between battery positive and battery negative power terminals of the inverter using a
resister between 10 ohm and 100 ohm.
Do not connect the inverter to a battery with a nominal value different from the value indicated on
the controller plate. If the battery value is greater, the MOS may fail; if it is lower, the control unit
does not "power up"
During battery charge, disconnect the controller from the battery.
Do not connect the controller to a battery with a nominal voltage different than the value indicated
on the controller label. A higher battery voltage may cause power section failure. A lower voltage
may prevent the logic operating.
Before doing any operation, ensure that the battery is disconnected and when all the installation is
completed start the machine with the drive wheels raised from the floor to ensure that any
installation error do not compromise safety.
Take care all the inductive devices in the truck (horn, solenoid valves, coils, contactors) have a
proper transient suppression device.
7-43
6. DISPLAY
1) STRUCTURE
The instrument panel has six built-in red LED, which provide the operator with an easy information
about the status of some truck devices.
13 7 10 8
HYUNDAI
M P
1 2 3 4 5 6 11 9 12
15B7OM65
1 Oil level warning lamp (option) 8 Key 2 button

2 Wrench warning lamp 9 Key 3 button
3 Thermometer warning lamp 10 Key 4 button
4 Seat warning lamp 11 Key 5 button
5 Seat belt warning lamp (option) 12 Key 6 button
6 Handbrake warning lamp 13 LCD function
7 Key 1 button
7-44
2) WARNING LAMP
When the key switch is OFF, the display makes a general test lighting and switching OFF all the
LED in sequence.
(1) Oil level warning lamp (Option)
This LED lights when the measured oil level of the hydraulic
circuit is under the minimum acceptable mark.
To connect the oil sensor output to the Analogue Input #1.
16B7OM61
(2) Wrench warning lamp

This LED blinks when truck is in alarm condition.
16B7OM62
(3) Thermometer warning lamp

This LED blinks when one truck's controller is in alarm due
IMS high temperature.
öIMS : Input motor switch
16B7OM63
(4) Seat warning lamp

This LED lights when the operator is not on the seat.
16B7OM64
(5) Seat belt warning lamp (Option)

(1) This LED lights to signal that the seat belt is not correctly
fastened. To connect the Seat belt sensor to the
Analogue Input #2.
16B7OM65
(6) Handbrake warning lamp

(1) This LED lights when the handbrake is activated.
16B7OM66
7-45
3) TESTER MENU
Status of keyboard buttons can be monitored in real time in the TESTER menu.
(1) Key 1 button
Status of keyboard button:
ON = Input active, button pushed
OFF = Input not active, button released
16B7OM67
(2) Key 2 button

Status of TURTLE keyboard button:
16B7OM68
(3) Key 3 button

Status of M M (Menu) keyboard button:
M
16B7OM69
(4) Key 4 button

Status of P P (Performance) keyboard button:
P
16B7OM70
(5) Key 5 button

Status of (Esc) keyboard button:
16B7OM71
(6) Key 6 button

Status of (Enter) keyboard button:
OFF = Input not active, button release
16B7OM72
7-46
4) LCD FUNCTION
1 5 2 3
7 8 6 4 15B7OM77
(1) Battery's state of charge

The battery's state of charge indication is displayed on the left side of the unit (1); it is shown by
ten notches. Each notch represents the 10% of the battery charge. As the battery becomes
discharged, the notches turn off progressively, one after the other, in proportion to the value of the
residual battery charge. When the residual battery charge is à 20 % the notches displayed start
to blink.
(2) Performance
The letter which appears in the rectangle displayed in the top right side of the unit (2) shows the
performance mode which is being used in the controller.
Performances can be scrolled pressing button P. When one performance is selected, the
related information will be sent via can-bus to traction and pump controllers that will manage this
data. The standard functioning reduces truck performance passing from the high to economic
performance.
The real meaning, in terms of parameters level of these performances, depends on software
present on pump and traction controllers:
- "H" corresponds to highest performance;
- "N" corresponds to normal performance;
- "E" corresponds to economic performance;
7-47
(3) Turtle
The turtle symbol (3) is normally off; when it appears (fixed) it shows activation of the "soft" mode
of the truck, in which maximum speed and acceleration are reduced. The "soft" mode can be
activated pressing button .
(4) Hour meter
The number displayed on the bottom right side of the unit (4) shows the Hours Worked.
The letter present near the hour meter shows which hour meter is displayed:
- K : the key hour meter is displayed;
- T : the traction hour meter is displayed;
- P : the pump hour meter is displayed; it increases if pump control is working.
(5) Accelerator
The accelerator level indication is displayed on the central top side of the unit (5); it is shown by
ten notches. When the accelerator level is minimum only a notch is displayed, when the
accelerator level is maximum all the ten notches are displayed. Each notch represents 1/10 of the
difference between maximum and minimum accelerator level.
(6) Speed
The number displayed under the accelerator notches on the center of the unit (6) shows the truck
speed. The unit can be km/h or mph depending on the SPEED UNIT parameter setting.
(7) Wheel position
The notch displayed on the left of the hour meter (7) represents the wheel (only one of the nine
notches is displayed) and shows the steering angle (it corresponds to the relative truck direction if
the truck is running).
(8) Running direction
The arrow (8) shows the set truck running direction. The arrow point is up when the truck is
forward running; the arrow point is down when the truck is reverse running. If the truck doesn't run
a dot is displayed instead of the arrow.
7-48
5) DESCRIPTION OF PROGRAMMABLE FUNCTIONS
(1) Menu set model
Η Connect to
Using CANBUS link, every module connected to can net can act as the "access node" to the
canbus net for the external world.
For example the ZAPI hand console (or the PC-Win console) can be physically connected to one
module and, by the canbus, virtually connected to any other module of the net.
This parameter is used to select the module to which the user wishes to be connected.
Following the numbers associated to each module in Zapi canbus system are showed.
Number associated in canbus net Module

03 TRACTION MASTER
04 TRACTION SLAVE
05 PUMP
09 MHYRIO (Option)
16 GRAPHIC SMART DISPLAY
(2) Menu set options

Η Power selector
It sets the truck performances.
OPTION #1 : H (High performance)
OPTION #2 : N (Normal performance)
OPTION #3 : E (Economic performance)
Θ Hour counter
It sets the hour counter displayed.
OPTION #1 : The key hour meter is displayed
OPTION #2 : The traction hour meter is displayed
OPTION #3 : The pump hour meter is displayed
Ι Auxiliary output #1
The options are :
PRESENT : An external load is connected between PAUX and NAUX.
The related diagnosis are enabled.
ABSENT : No external load is connected between PAUX and NAUX.
The related diagnosis are disabled.
Κ Auxiliary voltage #1
It specifies the percentage of battery voltage supplied to AUX coil to close the AUXILIARY electro
valve. This parameter can be changed in the range 0% to 100%.
Λ Speed unit
It sets the speed unit.
OPTION #1 : The speed unit is km/h
OPTION #2 : The speed unit is mph
Μ User password
The options are :
ON : After key-on a user password is asked to utilize the Graphic Smart Display
OFF : No user password needed
7-49
Ν Maintenance
The options are :
PRESENT : A maintenance hour-counter is incremented with key ON.
When the hours elapsed reach the programmed value with the display the warning
ÎSERVICE REQUIREDÏis shown.
ABSENT : NoÎSERVICE REQUIREDÏwarning
Ξ Maintenance done
It can be ON/OFF. This parameter is normally off. Setting theÎMAINT. DONEÏon at next key-on
the maintenance hours are updated with the displayÍs hour meter contents. This operation erases
theÎMAINTENANCE NEEDEDÏwarnig if it is present.
Ο Seat belt status
It sets theÎSeat beltÏdiagnostic LED indication in the following way:
OPTION #1 : NoÎSeat beltÏindication. The diagnostic LED is not used.
OPTION #2 : If the seat belt are not fastened at Key-ON the diagnostic LED blinks for three times
than it turns off.
OPTION #3 : The diagnostic LED blinks until the seat belt is fastened than it turns off.
Η Delay display OFF

This parameter sets the display ONÎService timeÏ. If the CNB#4 is connected to +batt after key-
off the display is still supplied for a programmable time, follow the table below to choose your
temporization :
Delay display
0 1 2 3 4 5 6 7 8 9
off level
Service time
[sec] 1 3 5 7 9 11 13 15 17 20
7-50
6) DESCRIPTION OF CONSOLE USING
(1) Access to SET MODEL menu.
The only parameter present in SET MODEL function is CONNECTED TO.
By setting this parameter, operator can connect ZAPI console to every ZAPI product connected to
CAN-BUS line. This functionality allows completely control of every ZAPI product without changing
the position of the console connector.
Η Opening Zapi menu.
Θ Press ROLL UP & SET UP buttons to enter

CONFIG MENU.
Ι The display will show: SET MODEL. If another
menu is displayed, press ROLL UP or ROLL
DOWN until SET MODEL appears.
Κ Press ENTER to go into the SET MODEL.
Λ The display will shows the first option, only

CONNECTED TO option is present in this menu.
Μ Press SET UP or SET DOWN buttons in order

to select the desired value for selected option.
Ν New desired value appears.
Ξ Press OUT to exit the menu.
Ο The display will ask "ARE YOU SURE?"
Π Press ENTER for YES, or OUT if you do not

accept the changes.
Ρ SET MODEL menu appears.
΢ Press OUT again. Console now disconnects

and reconnects.
Σ Display now shows the opening Zapi Menu of

the ZAPI product corresponding to option
selected at point 7.
20B7EL28
7-51
(2) Flow chart showing how to make changes to option menu:
⯱ Opening Zapi menu.
⯲ Press ROLL UP & SET UP Buttons to enter

CONFIG MENU.
⯳ The display will show: SET MODEL.
⯴ Press ROLL UP or ROLL DOWN until SET

OPTIONS appears.
⯵ SET OPTIONS menu appears.
⯶ Press ENTER to go into the SET OPTIONS

menu.
⯷ The display will show the first option.
⯸ Press ROLL UP or ROLL DOWN buttons until

desired option appears.
⯹ Desired option appears.
⯺ Press SET UP or SET DOWN buttons in order

to modify the value for selected option.
⯻ New value for selected option appears.
⯼ Press OUT to exit the menu.
⯽ Confirmation request appears.
⯾ Press ENTER to accept the changes, or press

OUT if you do not accept the changes.
⯿ SET OPTIONS menu appears.
⬼ Press OUT again. Display now shows the

opening Zapi menu.
20B7EL29
7-52
(3) Flow chart showing how to use the TESTER function of the digital console:
Θ Press ENTER to go into the MAIN MENU.
Ι The display will show: PARAMETER CHANGE.
Κ Press ROLL UP or ROLL DOWN until TESTER

menu appears on the display.
Λ The display will show: TESTER.
Μ Press ENTER to go into the TESTER function.
Ν The first variable to be tested is shown on the

display.
Ξ Press either ROLL UP or ROLL DOWN buttons.
Ο Next variable for measurement appears.
Π When you have finished press OUT.
Ρ The Display will show: TESTER.
΢ Press OUT again and return to opening Zapi

menu.
20B7EL30
Remember it is not possible to make any changes using TESTER.

All you can do is measure as if you were using a pre-connected multimeter.
7-53
7) DESCRIPTION OF ALARM MENU
The microprocessor in the controller records the last five alarms that have occurred. Items
remembered relative to each alarm are: the code of the alarm, the number of times the particular
alarm occurred and the hour meter count. This function permits deeper diagnosis of problems as
the recent history can now be accessed.
Flow chart showing how to use the ALARMS function via the digital console:
Θ Press ENTER to go into the MAIN MENU.
Κ Press ROLL UP or ROLL DOWN until ALARMS

menu appears on the display.
Λ The display will show:
Μ Press ENTER to go into the ALARMS menu.
Ν The display will show the most recent alarm.
Ξ Each press of ROLL UP button brings up

following alarms. Pressing ROLL DOWN returns
to the most recent.
Ο If an alarm has not occurred, the display will

show: NONE.
Π When you have finished looking at the alarms,

press OUT to exit the ALARMS menu.
Ρ The display will ask: "CLEAR LOGBOOK?"

Press ENTER for Yes, or OUT for No.
΢ Press OUT again and return to opening Zapi

menu.
20B7EL31
7-54
8) STRUCTURE OF DISPLAY MENU
Graphic Smart Display present a software structure made by menus and submenus. It is possible to
have access to Graphic Smart Display menu structure by the six operator buttons integrated in a
membrane keyboard.
At turn on the display shows the HYUNDAI logo for some seconds, then asks the starting password
to have access to the main page (if "USER PASSWORD" option is ON), otherwise it shows directly
the main page (if "USER PASSWORD" option is OFF).
The main page, if there aren't alarms, shows battery charge, truck speed (in km/h or mph, it
depends on "SPEED UNIT" parameter) and key/traction/pump hour meter (see "HOUR
COUNTER" option); if alarms are present, it will show alarm code, node initials in which alarm has
occurred and alarm description.
From the main page it is possible to have access to the ALARM page (if alarms occur) and to
MENUS page. The CHANGE PASSWORD MENU is always accessible and visible, while the
others ones are accesible and showed, by entering service password. To enter this password is
necessary to push the out button (button #5) of membrane keyboard; this will show a entering
password page.
By using service password it's possible to enter in all menus (TRUCK, CHANGE PASSWORD,
MAINTENANCE).
It follows flow chart diagram of menu structure.
7-55
2 seconds
ENTER PASSWORD
ENTER USER PASSWORD
------------------------------- SERVICE / ENGINEERING

0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
D 247 : PERFORMANCE ROLLING

CAN BUS KO
f l
I rm r H : high
N : normal
E : economy
MENUS
TRACK MENU MAINTENANCE
CHANGE PASSWORD
16B7SM23
7-56
ZAPI CONSOLE
TRUCK MENU The display will act like a

Zapi console.
SET
MAINTENANCE HOURS
MAINTENANCE
00000
CHANGE PASSWORD
ENTER OLD PASSWORD

----
1 2 3 4 5 6 7 8 9
ENTER OLD PASSWORD

ENTER NEW PASSWORD
----
1 2 3 4 5 6 7 8 9
PASSWORD HAS
BEEN CHANGED
PRESS OUT
MAIN PAGE
20B7EL41
7-57
(1) Performance rolling
From MAIN PAGE using membrane keyboard numbers, it is possible to select the performance
mode which must be used in traction and pump controllers.
Performance can be chosen with button 4, and it is displayed in the top right side of the unit.
When one performance is selected, the related information will be sent via canbus to traction and
pump controllers that will manage this data. The standard functioning reduces truck performance
passing from high performance mode (H) to economy performance mode (E).
The real meaning, in terms of parameters level of these performances, depends on software
present on pump and traction controllers.
Button 4 Selects in sequence the truck performance (H Ą N Ą E).
(2) Using dashboard like console

By entering the service or engineering password, from MAIN PAGE it's possible to have access to
TRUCK MENU, which allows user to use dashboard as a real Zapi digital console connected to
one module of canbus net.
Here with roll buttons (button 1 and 2 of membrane keyboard) and enter button (button 6), it is
possible to choose which module of canbus net has to be connected to the display.
When the display has been connected, it works exactly like a Zapi digital console.
Buttons of membrane keyboard do the same functions of Zapi console keys.
Button 1 Performs function of the ROLL UP console key
Button 2 Performs function of the ROLL DOWN console key
Button 3 Performs function of the SET DOWN console key
Button 4 Performs function of the SET UP console key
Button 5 Performs function of the OUT console key
Button 6 Performs function of the ENTER console key
(3) Using of password menu (option)

From MAIN PAGE it's always possible to have access to CHANGE PASSWORD MENU. Here with
ENTER button (button 6 of membrane keyboard) the operator can change user Graphic Smart
Display password.
To edit password use these buttons:
SET UP / SET DOWN Shifts cursor through 10 digits on the bottom side of unit
ENTER Inputs digit selected or saves all changing
OUT Cancels one digit or exits (if there is no digit input yet)
(4) Set maintenance hours (option)

By entering the service or engineering password from MAIN PAGE it's possible to access to
MAINTENANCE MENU. Here the service can change the programmed work hours between two
maintenances.
Buttons of membrane keyboard have the same functions in the RESET HOURMETERS MENU:
Button 1 Increases digit marked by cursor
Button 2 Decreases digit marked by cursor
Button 3 Shifts cursor on previous digit
Button 4 Shifts cursor on following digit
Button 5 Cancels all changing and out from hour meter submenu
Button 6 Saves all changing
7-58
9) ANALYSIS OF GRAPHIC SMART DISPLAY RELATED ALARMS
(1) Graphic Smart Display alarms
Η WATCHDOG
Cause:
At start-up the watch dog signal is already active before the software has generated it. At standby
or running condition the watch dog signal is not active (in alarm status).
Troubleshooting:
The WD hardware circuit or microcontroller output port are damaged. In both cases no external
component are involved. Replace the logic board.
Θ COIL SHORTED
Cause:
This alarm occurs when there is a short circuit of the AUXILIARY coil connected to CNB#1
output. After the overload condition has been removed, the alarm exits automatically by releasing
and then enabling a travel demand.
Troubleshooting:
A) The typical root cause for this error code to be displayed is in the harness or in the load coil.
So the very first check to carry out concerns connections between dashboard outputs and
loads.
B) In case no failures/problems have been found externally, the problem is in the logic card, which
has to be replaced.
Ι DRIVER SHORTED
Cause:
The driver of the auxiliary electro valve coil is shorted.
Troubleshooting:
A) Check if there is a short or a low impedance pull-down between NAUX (CNB#1) and -BATT.
B) The driver circuit is damaged in the logic board, which has to be replaced.
Κ AUX DRIVER OPEN
Cause:
The AUX coil driver is not able to drive the load. The device itself or its driving circuit is damaged.
Troubleshooting:
This type of fault is not related to external components; replace the logic board.
Λ HARDWARE FAULT
Cause:
At key-on the dashboard checks if the AUX driver is turned off by a not active (alarm status)
watch-dog signal. If it is not turned off then the alarm is generated.
Troubleshooting:
The problem is inside the logic, no external component are involved, replace the logic board.
7-59
Μ CAN BUS KO
Cause:
Graphic Smart Display doesn't receive messages from canbus line or the hour meter
synchronization at key-on fails.
Troubleshooting:
A) If this fault code is displayed together with other alarm messages, the fault is probably to be
looked for in the Graphic Smart Display can interface, since the display seems to be unable to
receive any can message. So it is suggested to check Graphic Smart Display canbus wiring
and connection.
B) Otherwise, the fault is in the can interface of other modules present on canbus network.
(2) Graphic Smart Display warnings

Η EEPROM KO
Cause:
It's due to an HW or SW defect of the non-volatile embedded memory supporting the dashboard
parameters. This alarm does not inhibit the machine operations, but the truck will work with the
Graphic Display parameters default values.
Troubleshooting:
Try to execute a CLEAR EEPROM operation (refer to console manual).
Switch the key off and on to check the result. If the alarm occurs permanently, it is necessary to
replace the logic. If the alarm disappears, the previously stored parameters will have been
replaced by the default parameters.
Θ MAINTENANCE NEEDED
Cause:
This is just a warning to call for the time programmed maintenance.
Troubleshooting:
It is just enough to turn the MAINTENANCE DONE option to level ON after the maintenance is
executed.
(3) Alarms visualization

When an alarm condition occurs, Graphic Smart Display gives the information showing the initial
of module in which the alarm occurred, the alarm code and description.
For example, the information:
M 245:
WRONG SET BAT
means that the alarm 245 - "WRONG SET BATTERY" occurred in the master traction controller
(M).
Here the table with the alarm codes and the respective meaning is shown.
7-60
10) DIAGNOSTIC FAULT CODES
Condition that has to occur
Code Alarm string Master Slave Pump Description to come out from
alarm status
8 WATCHDOG X X X Alarm : The Watchdog ÂIf the alarm is present in
circuit has been Init status, remove the
triggered. alarm condition
ÂIf the alarm has occurred in
standby or running mode, it
is necessary to remove
alarm condition and to
activate a traction request
17 LOGIC X X X Alarm: Failure in over- To remove alarm condition
FAILURE #3 load protection hw + activation of traction
circuit request
18 LOGIC X X X Alarm: Failure in U, V, To remove alarm condition
FAILURE #2 W voltage feedback + activation of traction
circuit request
19 LOGIC X X X Alarm: An overvoltage To recycle the key switch
FAILURE #1 or undervolt.
Condition has been
detected.
30 VMN LOW X X X Alarm: Wrong voltage ÂIf the alarm is present in
on motor power out- Init status, remove the
puts; Failure in the alarm condition
power section or in ÂIf the alarm has occurred in
the mosfet driver standby or running mode, it
circuit or in the motor is necessary to remove
31 VMN HIGH X X X Alarm: Wrong voltage ÂIf the alarm is present in
on motor power Init status, remove the
outputs; Failure in the alarm condition
power section or in ÂIf the alarm has occurred in
the mosfet driver standby or running mode, it
circuit or in the motor is necessary to remove
53 standby I X X X Alarm: Wrong voltage ÂIf the alarm is present in
HIGH in the current sensor Init status, remove the
feedback circuit alarm condition
60 X X X Alarm: Power capaci- To remove alarm condition
CAP tor voltage does not
CHARGE increase when the key
is turned ON; Failure
in the power section,
or in the Logic PCB,
or in the driver PCB,
or in the motor
7-61
alarm status
74 DRIVER X X Alarm: Line contac- ÂIf the alarm is present in
SHORTED tor coil driver is Init status, remove the
shorted alarm cause
alarm cause and to
activate traction request
75 CONTACTOR X X Alarm: Line contac- To remove alarm cause
DRIVER tor coil driver is open and to activate traction
(not able to drive the request
coil to the correct
voltage)
76 COIL X X Alarm: ÂIf the alarm is present in
SHORTED ÂInit: The LC and EB Init status, remove the
coil driver protection alarm cause
circuit is damaged ÂIf the alarm has occurred in
ÂStandby or running: standby or running mode, it
short on LC coil or is necessary to remove
EB coil alarm cause and to
37 CONTACTOR X Alarm: Line contac- To remove alarm cause
CLOSED tor power contact is within a timeout; if the
stuck timeout is elapsed, it is
necessary to re-cycle the
key
38 CONTACTOR X Alarm: Line contac- To remove alarm cause
OPEN tor power contact within a timeout; if the
does not pull-in timeout is elapsed, it is
necessary to re-cycle the
key
82 ENCODER X X X Alarm: Motor speed To recycle the key
ERROR sensor (encoder)
does not work
properly
84 STEER X Alarm: Steering poti To remove alarm cause
SENSOR KO signal out of range
86 PEDAL WIRE X X Alarm: Fault in To remove alarm cause
KO accelerator negative and activate a traction
(NPOT) input circuit request
245 WRONG SET X X Alarm: The battery To remove alarm cause
BATTERY voltage does not
correspond to SET
BATTERYprogram-
ming
246 SLAVE KO X Alarm: Master ʂC To recycle the key
detects a Slave ʂC
malfunctioning
7-62
alarm status
247 MASTER KO X Alarm: Slave C de- To recycle the key
tects a Master C
malfunctioning or a
mismatch between
inputs status and Mast
-er commands (via
Canbus)
250 INPUT X Alarm: Slave C has To recycle the key
MISMATCH detected a mismatch
between inputs status
and the input status
transmitted via Can-
bus by Master C
253 AUX OUTPUT X X Alarm: MCV SOL If the alarm is present in
KO driver shorted or open Init status, remove the
alarm cause
If the alarm has occurred in
alarm cause and to
13 EEPROM KO X X X Warning: Eeprom To remove Warning cause
fault, controller will use
default parameters
61 HIGH X X X Warning: Master or To remove Warning cause
TEMPERATU- Slave or both tempera
RE -ture higher than 75 C
65 MOTOR X X X Warning: Master or To remove Warning cause
TEMPERATU- Slave or both motors
RE temperature high
66 BATTERY X Warning: Battery ch- To remove Warning cause
LOW arge level below 10%
71 HANDBRAKE X Warning: Handbrake To remove Warning cause
microswitch is open
and a travel request is
active
78 VACC NOT X X Warning: Acc.signal To remove Warning cause
OK (CPOT)voltage higher
than VACC MIN +1V
while the traction en-
able switch is open
79 INCORRECT X X Warning: Wrong trac- To remove Warning cause
START tion request sequence
80 FORWARD + X Warning: Forward and To remove Warning cause
BACKWARD reverse inputs are
both active
249 THERMIC X X X Warning: Master or To remove Warning cause
SENSOR KO slave temp. sensor is
out of range
7-63
alarm status
251 WAITING X Warning: Master ʂC To remove warning cause
FOR NODE signals that slave or
pump ʂC is in alarm
status
251 WAITING X Warning: Slave ʂC To remove warning cause
FOR NODE#3 signals that master ʂC
is in alarm status
247 NO CAN X X Alarm: To remove Alarm cause
MESSAGE #X Master/Slave has lost
Can communication
with #X
250 CANBUS KO X Alarm: To remove Alarm cause
Inverter has lost Can
communication
240 MOTOR X Warning: The encoder To recycle the key
STALL signal is constantly
zero when the maxi-
mum torque is applied
to the motor
243 SEQUENCE X Warning: An incorrect To remove warning cause
FAULT start sequence has
been detected on the
seat, pedal and levers
commands
254 CANBUS KO X Alarm: Master has lost
DISP. can communication
with the display
252 CHAT MODE X Warning: The chat To activate traction or
time has expired pump request
248 DISPLAY X Warning: The display To remove warning cause
ENABLE enable signal has not
been received to
operate the truck
242 PUMP X Warning: A warning is To remove warning cause
WARNING active on the pump
module
7-64
7. BATTERY CHARGER
This explains basic information related to charger to help you easily understand and use it. This
includes the contents from the way to install a charger to tips for emergency situations. This is focused
on practices aiming to be usefully utilized in the field.
1) BASIC INFORMATION
(1) What is charger
Charger is a device which makes a battery accept D.C electricity under optimal condition as it
transforms A.C provided from external source of electricity.
The charger is a constant-current and constant-voltage way, SCR type charger that it has
advantages as follows
Η Even though A.C input voltage fluctuates within 10% of rated voltage (220/380/410/440V), the
current and voltage provided to the battery are stable.
Θ As minimizing the increase of temperature while charging a battery, it minimizes the stress on the
battery.
Ι The noisy of charger is minimal but the charging efficiency is very high.
Κ It prevents from under charging and overcharging.
Therefore, it helps the battery to maintain its performance for longer time and to prolong the life of
the battery.
(2) Notice on caring chargers

Η If any abnormal status is found while using a charger, immediately stop using and check the
charger. If it is impossible to take an appropriate measure for yourself, please apply for A/S.
Θ While charging, hydrogen and oxygen gas is produced. Use or approach of fire should be strictly
prohibited.
Ι Keep clean to prevent from sneak current and attack on the interface and surroundings of the
battery.
Κ Check the electrolyte of the battery every week and provide distilled water immediately if it is
required. ( Electrolyte has to be provided between 10~12mm level on the positive plate inside
storage battery)
Λ If battery liquid temperature becomes over 55ÁC, charging should be stopped.
If it is continued,
- the appearance is transformed
- and metal area can be attacked as electrolyte overflows
Μ Electric forklift truck using battery should be charged as soon as the charging lamp is on while
driving. As batteries are internally discharged naturally if they are deposed for a long time, charge
them once or twice a month to prevent from reducing the lives of batteries.
Ν When a green sign is on among charging status indication lamps, please notify that it is not
converted as equalized charge for stabilization of charging status.
7-65
(3) Names of each part (independent items)
1 5
3
6 9 10
7
2
11
BR7BAT30
1 Main PCB board 5 Shunt 9 Resistance (RD)

2 Main trans (Class H) 6 NFB 10 Resistance (DR)
3 Cooling fan 7 MG S/W 11 TAP changer
4 SCR module 8 Assistant trans
7-66
2) CHARGER INSTALLATION METHOD
(1) Location for charger installation
Η Dry and well ventilated place.
Θ No inflammable and B7 fire are near by.
Ι Safe place where no collision possibility
with people or equipment is.
(2) Check points before installing charger
Η Enough capacity of AC input power
source to operate charger.
Θ Standard electric wire for power source
by capacity.
Display
3) HOW TO USE A CHARGER
(1) General charging method (Floating

charging) Θ
Η
Η Charging by this method supplies electric

power to the charger as operating Θ
external AC power switch of the charger. Ι
Θ Connect battery connecter and charger Η
connecter.
BR7BAT10
ÂAccording to charging condition
Η If there is no abnormality found when the
charger checks itself for 3-4 seconds
after inputting AC input power source, the
charger slowly increases the electric flow
for charging and the charging condition
lamp in the lower part of the front panel
for floating charging of "input" is on.
Θ When charging is processed about 80%,
yellow lamp in the middle of the front
panel, which shows that the charging
condition is in the middle, is on and then
green lamp is on when charging is
processed over 85% until charging is
completed.
Ι When charging is completed, "charging is
completed" lamp is on in the monitor and
other lamps of all monitors become off.
7-67
(2) Equalized charging
Η Equalized charging is
Equalized charging is to correct the
battery when it does not normally
perform its functions as the voltage
differences are too big between cells of a
battery.
When equalized charging is required?
- When re-operates the battery after
having left the battery for a long time.
- When a battery is over-discharged.
- When there is large deviation of voltage
and specific gravity between battery
cells.
- When change or supply electrolyte of
battery.
Θ Tips for equalized charging
If once push the equalized charging
button on the monitor in the beginning of
charging, the equalized charging lamp
becomes on and starts charging.
ö When the green charging condition
lamp is on ( over 85% charged), the
equalized charging switch is locked
that it does not operate even pushing
Equalized charging switch
the button. BR7BAT10
7-68
4) HOW TO CHECK THE CHARGER'S NORMAL OPERATION
After changing SCR module or PCB (SE-
5000SN), the charger's normal operation
should be checked.
ÂChecking order
(1) Separate the charger and battery
connector.
(2) Separate lower cover in the front of the
charger.
(3) Check the AV input voltage used from the
input switch terminal in the lower left side
of the inside of the charger.
Checking method between terminals.
Input voltage setting value Ą 220V 380V
- Between terminals No. 2 - No. 4 220V 380V
ö Above cases are under normal BR7BAT05
operations.
ö When installing charger for the first time
220V
or moving its location, check and make
it sure if the voltage is appropriately
connected.
Refer to No. 2 of the charger installation
method for the terminal connection
method.
- In case of 220V : (2), (4), (6), (8)
- In case of 380V : (1), (3), (5), (7)
It should be connected to the terminal.
380V BR7BAT06
7-69
(4) Convert the automatic / manual switch to
manual.
The automatic/manual switch is located in
the lower left part of the PCB
Be sure to check if battery connector is
separated in advance.
(5) MG/SW operation
(This switch is operated automatically.)
(6) Check the charging voltage soft start BR7BAT08
function (refer to the monitor)

Η After 5 seconds next to turn the manual
switch on.
Input, floating charge and red charging
condition lamp is on.
Θ After 15 seconds next to turn the manual
switch on.
Yellow charging condition lamp is on
while charging.
Ι After green lamp becomes on, measure BR7BAT09
the output voltage of the battery

connector by multi measure. If measured
voltage is between 62.5V ~ 63.5V, it is
normal. (Rated voltage : 63V)
Κ After 30 seconds next to turn on the Η
manual switch, if buzzer rings for 10 Ι
seconds and END lamp is on, it is under Θ
normal condition.
ö When yellow lamp under charging
condition is on after 1~2 times
BR7BAT10
repetition, convey the automatic/
manual switch to the automatic and
check if the charger trips automatically.
7-70
(7) If charger's out voltage is under 60V, it is
abnormal.
Please refer to the error sheet.
(8) When the charging voltage is indicated as
normal condition (63V), convert automatic
/ manual switch to automatic and start
charging.
ö Display error code on the front cover as BR7BAT11
following table.
No Code Description of error
1 E.F EPROM fail

2 O.V Over voltage - Refer to page 7-73
3 O.C Over current - Refer to page 7-72, 74.
4 F.B Battery error (After starting charging, the voltage doesn't go over 52V for 2 hours.)
Check the battery.
5 O.T Transformer over heat (Stop charging when it is over 160ÁC).
- If input voltage is high, output current is over normal value and there is heat in the
trans because of SCR control part fault.
- Check the output current and PCB control board
6 O.H Heatsink over heat (Stop charging when it is over 100ÁC).
- Check the cooling fan, SCR connection cable contact point and control part.
7 A.O Power supply error (input power 220/380V wrong wiring). - Refer to page 7-71.
8 A.F Power supply error (absent phase) - Check if input cable is open.
9 A.C AC fail (black out) - Check if input voltage is right.
10 L.C Low current (If this sign is on for setting value (60 sec), charging is over).
11 F Manual stop.
7-71
5) CHECK POINTS BEFORE APPLYING
A/S
(1) AC input power source switch is input.
(2) Check if the battery connector of the
forklift truck and charger's connector are
connected.
(3) Check points when "Error" lamp is on in
the front monitor of the charger.
(4) Check the front cover indicator. BR7BAT10
Η A.F : Input three phase power source

continuity check = Check if input three
phase power source is normal with AC
voltage meter.
Θ A.O : Error on selection of input power
source of 220V or 380V - Check it
appropriately with full three phases.
Ι A.C : Check if the input power source
(220V or 380V) is normal.
Κ O.C : Check the electric current, as
charging current of the battery is over-
standards condition.
Λ O.V : Check the voltage, as charging
voltage of the battery is over-voltage
condition (66V).
Normally it is 63VÜ1V.
(5) Check other abnormalities as well.
Then apply for A/S when on-site
measurements are not applicable.
7-72
6) ERROR DETECTION
(1) Error list
Η Only floating charge lamp is on in the
monitor but it is not charged.
Θ ON and OFF is repeated with a few
minutes intervals even after starting
charging.
Ι Charger TRIP is occurred after
abnormality lamp is on.
In case error code is "O.V"
Κ Charger TRIP is occurred after
abnormality lamp is on.
In case error code is "O.C"
Λ Charger TRIP is occurred after it started
charging and charging completion lamp
is on.
Μ Charger has no response even the
battery connector is connected.
7-73
(2) Troubleshooting
Η Only floating charge lamp is on after indicating "A.O", It's not charged.
Â 220/380V Model : Measure the TB.4 (380V) TB.8(220V)

voltage between input voltage
change over tabs 2-4 2-6 4-6 70̫/
Â 220,380,410,440V Model : 30W
Measure the voltage in front of In front of MS Manual/Auto TAP Changer M/S
AC INPUT MS S/W B
T.B
After separating short 7 8
bar
battery connecter, AC
PCB PCB RY
Check convert the INPUT (LP lamp)
YES YES LP YES Voltage
the rated automatic/manual MS
lamp tap
voltage selection switch on switch
ON?
the lower part of ON J2
PCB to manual.
NO NO
TH
Apply multi tester for input voltage change Change PCB Manual
over tab no. 6 /Auto S/W
Measure voltage between input tab no.8, CN4 contact fault
M/S
PCB CN4, and contact points with red reed PCB RY contact fault COIL FAN
NO putting black reed on the other side
Apply multi tester for input voltage change
TB.6
over tab no. 6
M/S electrical circuit
TH contact fault
Voltage NO CN4 contact fault

Input power source is not 220V?
PCB RELAY fault
provided.
YES TH manual
Â Check external lead cable.
restoration release
Â Check the connection of MS COIL fault CN4 RY
external input connecter
Â Check external NFB TRIP
7-74
Θ ON and OFF is repeated with a few minutes intervals after starting charging.
Indicate "O.C" on the monitor.
- TH is operated (AC input over-current TRIP).
OUTPUT
CURRENT
DE- IN-
CREASE CREASE
Serious
trans noisy Measure output Current Exceed Adjust output current
NO NO
under the current using DC value : 15~20A Standard within PCB
condition. current measure /100AH current Re-adjust to VR
Is MS
on? YES
Â TH Setting fault
YES
Â Re-adjust TH TH. TRIP Change TH
setting value
NO
* Refer to SCR Rated
Complete Current
YES Module checking
method SETTING
YES NO
Complete Change PCB
NO Change
SCR MODULE
Separate the battery Check
connector and tune SCR
the charger off Module
YES Check
Check the normal
MAIN NO Change
operating condition
TRANS PCB
of the charger
VOLT
YES
7-75
Ι Charger TRIP is occurred after abnormality lamp is on.
In case error code is "O.V" Ą Over-voltage output / Set at 66Vdc (In case of BATT 48V)
After separating the battery connecter, Check Turning charging voltage volume in
turn on MS as converting the voltage of the NO the center of the right-hand side of
automatic/manual selection switch on output connecter PCB anti-clockwise rotation
lower part of PCB to manual 62-63V? Set the voltage same as 62.5V
Re-establish voltage
De- In-
establishment volume "17/0V" crease crease
YES
on the lower right side of PCB Measure
as turning it anti clockwise YES the voltage of the VOLT
rotation output connecter
62-63V?
Check contact error
or breaking of wiring NO Change
De- In- OK NO of the detect cable PCB
crease crease
Measure connecter pin
the voltage of the
output connector Check
62-63V? the detect
YES voltage of the J3 NO
NO YES
connector
Change PCB OK
7-76
Κ Charger TRIP is occurred after abnormality lamp is on.
In case error code is "O.C" Ą Output over current, established as 120% of the rated
current.
De- In-
crease crease
Measure
Re-establish the charging current
Restart the charger as pushing the output current by NO
volume in the center of PCB as turning
reset switch in the monitor. DC current measure
it anti clockwise rotation
AH÷8
YES
Re-establish or release the

Measure
output over-current volume
the output current
"9/OC" on the lower left side
by DC current
of PCB as turning it anti
measure
clockwise rotation
YES NO
Change
OK
PCB
After RESET
Check charger
YES NO
Decrease Increase
Change
OK
PCB
7-77
Λ Charger TRIP is occurred after it started charging and charging completion lamp is on.
(In case input voltage is normal - Refer to the error detection No. 1)
Restore the charger as pushing reset switch.
Measure
After separating battery connector,
the output current by NO Measure the output
put the automatic/manual selection
DC current measure voltage 62-63V
switch to manual
Is it normal?
YES
YES
Re-establish voltage establishment volume "17/0V" NO

on the lower right side of PCB as turning it anti Contact fault between
clockwise rotation. Check
the battery connector
After connecting the battery connector TRIP is not SCR Module
and charger connector
occurred and hold the volume at the point that TRIP Is it ok? Battery is over-
is occurred in 10 ~ 15 sec after disconnect the discharged
battery connector. (Try it 2 or 3 times.)
NO YES
Change Change
SCR Module PCB
Decrease Increase
7-78
Μ Charger has no response even if the battery connector is connected.
- In case only floating LED is on, charger input power is cut off or doesn't connect. (In case
the input voltage is normal - Refer to the error detection No. Η )
NO Charger BATTERY
Connector contact fault
Battery
Measure Measure the
NO voltage
the battery voltage voltage within the is normal
Is it under RD of the charger (Over
35V? BATT(+) SHUNT 35V)
CN.6
YES RD PCB(+) YES
PCB(-)
BATT(-) Module
(-) PCB
(+)(-) Voltage Check the cable and contact
is over YES point status at PCB connector(J3)
12V
On the
Convert the automatic/manual selection switch
left side of PCB
to manual and turns it to automatic after 1/2~1
Is LP LED
hour and make it charge normally. NO NO
ON?
If the battery voltage is not increased after
automatic 1 hour charging is started, battery YES Change
check is required. PCB
Refer to the error detection No.Η

Change Check the input power wire line
RD 300/500W in the charger
RD
LED
7-79
7) HOW TO CHECK THE SCR MODULE
Circuit Real diagram
K2 K2
G1
K1 G1
3 2 1 K1
* Before checking SCR MODULE, be sure to disconnect bus bar and wire on the terminal.
Measuring point
No. Measure value SURGE PCB
(Real diagram)
1 No.1 ~ No.3 Forward : Under 100 k ohm

Reverse : Infinity ( ∞ )
2 No.2 ~ No.3 Forward : Infinity ( ∞ )

3 G1 ~K1 Forward : Under 100 ohm

Reverse : Under 100 ohm
But It depends on the module.
If it is not 0 ohm, It is Ok.
4 G1 ~ K2 Forward : Infinity ( ∞ )
7-80
8) PCB MAJOR PARTS NAME AND LOCATION
16
1
2
15
3
12 5
13 6
7 8 9 10 11
14
BR7BAT24
1 Micro control unit #1 7 Over voltage 13 Set input over current

2 Micro control unit #2 8 Monitor level yellow 14 Auto/manual switch
3 CN6 voltage detect 9 Monitor level green 15 SCR control connector
4 SH current detect 10 Under current 16 CN4 RY contact point
5 Adjust charging current 11 Over current
6 Adjust charging voltage 12 Set input over voltage
7-81

Section 7 Electrical System: Group 1 Component Location

Uploaded by

Copyright:

Available Formats

Section 7 Electrical System: Group 1 Component Location

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Section 7 Electrical System: Group 1 Component Location

Uploaded by

Copyright:

Available Formats

SECTION 7 ELECTRICAL SYSTEM

GROUP 1 COMPONENT LOCATION

1 Combination switch 8 Back up alarm 15 High horn

F4 F6 F7 F8 F9 F10 F11 F12

20 HEAD 25 26 27 29 55 55A 52A

PARKING TILT S/W

191 122A 04 291

FUSE BOX ASSY

F4 F6 F7 F8 F9 F10 F11 F12

20 HEAD 25 26 27 29 55 55A 52A

PARKING TILT S/W

191 122A 04 291

1. FUNCTIONS OF BATTERY FORKLIFT TRUCK AND ELECTRIC COMPONENTS.

3) SPECIFICATION AND SERVICE DATA

Item Unit 15BT-7/16B-7 18/20BT-7, 18/20B-7

Fully charged specific gravity 1.280(25ÁC)

Minimum Level Maximum Level

Nature of trouble Symptoms Causes Repair

300 220 226 224 223 222 225

51 Stator 335 Circlip 700 Rotor

Item Unit Specification

300 700 515

51 Stator 320 Ball bearing 524 Amp pin

Item Unit Specification

3) INTERNAL INVOLUTE SPLINE DATA

Item Unit Specification

Flat root side fit - Class 7

Traction controller Pump controller

15/18/20BT-7 DUAL AC2 Traction AC 36-48V, 330A+330A 330A / 3min

CONN C CONN B CONN A

Θ Connection of encoder with open collector output; +5V power supply.

Ι Connection of encoder with open collector output; +12V power supply.

AC-2 INVERTER Voltage -BATT

No. of pin Function Description

Η Opening Zapi display.

Θ Press ENTER to go into the general menu.

Ι The display will show:

Κ Press ROLL UP or ROLL DOWN button until

Λ The display shows:

Μ Press ENTER to go into the SAVE function.

Ν If this facility has been used before the type of

Ο Press ENTER to commence SAVE routine.

Π You can see the items that are being stored

Ρ When finished, the console shows :

΢ Press OUT to return to the opening Zapi display.

Η Opening Zapi display.

Θ Press ENTER to go into the general menu.

Ι The display will show:

Κ Press ROLL UP or ROLL DOWN button until

Λ The display shows:

Μ Press ENTER to go into the RESTORE PARAM

Ξ Keep pressing either ROLL UP or ROLL DOWN

Ο Press ENTER to commence restore operation.

Π The display asks "ARE YOU SURE?".

Ρ You can see the items that are being stored in

Η Opening Zapi display.

Θ Press ENTER to go into the general menu.

Ι The display will show:

Κ Press ROLL UP or ROLL DOWN button until