0% found this document useful (0 votes)
5K views4 pages

Armorseal Heavy Duty Floor Coatings

This document provides information about ArmorSeal 8100, a water based epoxy floor coating. It describes the product's features, recommended uses, surface preparation instructions, test results, application details, and more. The coating is suitable for commercial, industrial and residential floor applications and offers durability, chemical resistance, and breathability.

Uploaded by

Mohindra Persad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
5K views4 pages

Armorseal Heavy Duty Floor Coatings

This document provides information about ArmorSeal 8100, a water based epoxy floor coating. It describes the product's features, recommended uses, surface preparation instructions, test results, application details, and more. The coating is suitable for commercial, industrial and residential floor applications and offers durability, chemical resistance, and breathability.

Uploaded by

Mohindra Persad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

ArmorSeal ARMORSEAL® 8100

Heavy WATER BASED EPOXY FLOOR COATING


Duty Floor
Coatings P
P
A
A
B70-8100 S
B70-8160 S
G
S
P B B70V8100 H
Revised: November 4, 2019 8.18

P਱ਮਣ਴ਢਲ਼ Dਤਲਢ਱ਨਯਲ਼ਨਮਭ Rਤਢਮਬਬਤਭਣਤਣ Uਲਤਲ


ARMORSEAL 8100 is the next generation in water based epoxy floor Durable epoxy floor coating for general purpose use in industrial
coatings; a two-component polyamine epoxy with excellent chemical and and commercial environments, such as:
abrasion resistance that is breathable. It is designed for use in commercial,
industrial and residential floor applications. A LEED v4.1 compliant material
• Warehouse Floors
that offers improved performance while maintaining ease of application • Garages
properties common to water based materials. This versatile material is • Residential
self-priming over concrete, can be used as a stand alone coating or as a • Automotive Showrooms
receiver coat for paint chip floors. Available in a gloss or satin finish • Industrial and Commercial Floors
• Breathable • Light manufacturing Plants
• <50 g/L
• Color Retention, resists yellowing
• Acceptable for use in USDA inspected facilities
• Resists disbondment due to Moisture Vapor Transmission (MVT)
• Ease of application Pਤ਱ਥਮ਱ਬਠਭਢਤ Cਧਠ਱ਠਢਲ਼ਤ਱ਨਲਲ਼ਨਢਲ
P਱ਮਣ਴ਢਲ਼ Cਧਠ਱ਠਢਲ਼ਤ਱ਨਲਲ਼ਨਢਲ Substrate: Concrete
Finish: Gloss or Satin Surface Preparation: Clean, dry, sound
Color: Clear*,Tile Red, Deck Gray, Haze Gray System Tested:
and a wide range of tinted colors using
CCE colorants 2 cts. ArmorSeal 8100 @ 2.0 - 4.0 mils (50-100 microns) dft
Safety Colors Gloss only
* For Clear, use the Ultra Deep Base (for more detail, see Application Bul-
letin Performance Tips
Volume Solids: 41% ± 2%, mixed, may vary by color Test Name Test Method Results
Weight Solids: 50% ± 2%, mixed, may vary by color ASTM D4060,
VOC (EPA Method 24): <50 g/L; 0.42 lb/gal, mixed Abrasion
CS17 wheel, 1000 150 mg loss
Mix Ratio: 4:1 by volume Resistance
cycles, 1 kg load
Adhesion ASTM D4541 550 psi concrete
Recommended Spreading Rate per coat:
Finish Satin 15-25 units@ 85º
Minimum Maximum Gloss 90+ units @ 60º
Wet mils (microns) 5.0 (125) 12.0 (300) 180º bend
Dry mils (microns) 2.0 (50) 5.0 (125) Flexibility ASTM D 522
1/8" mandrel
~Coverage sq ft/gal (m2/L) 130 (3.3) 320 (8.1) Impact Resistance Direct 100 in.lb.
NOTE: Brush or roll to cove base or vertical surfaces may require ASTM D2794
Indirect 80 in.lb.
multiple coats to achieve maximum film thickness and uniformity of
appearance. Pencil Hardness ASTM D3363 H

Drying Schedule @ 7.0 mils wet (175 microns): ASTM C1028**,


@ 50°F/10°C @ 77°F/25°C @ 120°F/49°C Passes wet and dry,
Slip Resistance, .60 Minimum Static
50% RH with and without
Floors Coefficient of Fric-
To touch: 1 hour 45 minutes 25 minutes SharkGrip Additive
tion
To recoat*:
WVP Perms (US) Grains(hr ft2 in Hg) Gloss – 2.0
minimum: 8 hours 6 hours 3 hours
Satin – 5.0
maximum: 72 hours 72 hours 72 hours
To Cure 7 days 7 days 7 days Hot Tire Pick-up ITM @ 140ºF Passes
Foot Traffic: 18 hours (60ºC)
Heavy Traffic: 48 hours
Drying time is temperature, humidity, and film thickness dependent. **Test method withdrawn in 2014 without replacement
*If recoating after 72 hours abrade surface first.
Pot Life: 8 hours 5½ hours 3½ hours
Sweat-in-Time: None None None

Shelf Life: Part A: 24months, unopened


Part B: 36 months
Store indoors at 40°F (4.5°C) to 100°F (38°C)
Flash Point: >230°F (110°C), Seta Flash, mixed
Reducer/Clean Up: Water

www.sherwin-williams.com/protective continued on back


ArmorSeal ARMORSEAL® 8100
Heavy WATER BASED EPOXY FLOOR COATING
Duty Floor
Coatings P
P
A
A
B70-8100 S
B70-8160 S
G
S
P B B70V8100 H
Revised: November 4, 2019 P I 8.18

Rਤਢਮਬਬਤਭਣਤਣ Sਸਲਲ਼ਤਬਲ S਴਱ਥਠਢਤ P਱ਤਯਠ਱ਠਲ਼ਨਮਭ


Dry Film Thickness / ct.
Surface must be clean, dry, and in sound condition. Remove all
Mils (Microns)
oil, dust, grease, dirt, loose rust, and other foreign material to
Concrete Floors, unpainted:
ensure adequate adhesion.
1 ct. ArmorSeal 8100 2.0-4.0 (50-100)
(reduced with one pint of water per gallon)
Refer to product Application Bulletin for detailed surface prepara-
2 cts. ArmorSeal 8100 2.0-4.0 (50-100) tion information.
Concrete Floors, previously painted: Do not use hydrocarbon solvents for cleaning.
1 ct. Spot prime bare areas with
ArmorSeal 8100 2.0-4.0 (50-100) Minimum recommended surface preparation:
Concrete & Masonry: SSPC-SP13/NACE 6, or ICRI
2 cts. ArmorSeal 8100 2.0-4.0 (50-100) No. 310.2R, CSP1-3

Wood Floors: Wood Floors: Clean, smooth, dust free


2 cts. ArmorSeal 8100 2.0-4.0 (50-100)
Tਨਭਲ਼ਨਭਦ
Tint part A with CCE colorants at 100% strength. Five minutes
minimum mixing on a mechanical shaker is required for complete
The systems listed above are representative of the product's use, mixing of color.
other systems may be appropriate.

Aਯਯਫਨਢਠਲ਼ਨਮਭ Cਮਭਣਨਲ਼ਨਮਭਲ
Temperature: 50°F (10°C) minimum, 100°F (38°C)
maximum
(air, surface, and material)
At least 5°F (2.8°C) above dew point
Relative humidity: 85% maximum

Refer to product Application Bulletin for detailed application information.

O਱ਣਤ਱ਨਭਦ Iਭਥਮ਱ਬਠਲ਼ਨਮਭ
Packaging: 1 gallon (3.78L) and 5 gallon (18.9L)
containers

Weight: 9.9 ± 0.2 lb/gal ; 1.12 Kg/L


mixed, may vary by color

Sਠਥਤਲ਼ਸ P਱ਤਢਠ਴ਲ਼ਨਮਭਲ
Refer to the SDS sheet before use.

Published technical data and instructions are subject to change without notice.
Contact your Sherwin-Williams representative for additional technical data and
instructions.

Wਠ਱਱ਠਭਲ਼ਸ
The Sherwin-Williams Company warrants our products to be free of manufactur-
Dਨਲਢਫਠਨਬਤ਱ ing defects in accord with applicable Sherwin-Williams quality control procedures.
The information and recommendations set forth in this Product Data Sheet are Liability for products proven defective, if any, is limited to replacement of the defec-
based upon tests conducted by or on behalf of The Sherwin-Williams Company. tive product or the refund of the purchase price paid for the defective product as
Such information and recommendations set forth herein are subject to change and determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
pertain to the product offered at the time of publication. Consult your Sherwin- OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
Williams representative to obtain the most recent Product Data Information and STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
Application Bulletin. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

www.sherwin-williams.com/protective
ArmorSeal ARMORSEAL® 8100
Heavy WATER BASED EPOXY FLOOR COATING
Duty Floor
Coatings P
P
A
A
B70-8100 S
B70-8160 S
G
S
P B B70V8100 H
Revised: November 4, 2019 A B 8.18

S਴਱ਥਠਢਤ P਱ਤਯਠ਱ਠਲ਼ਨਮਭਲ Aਯਯਫਨਢਠਲ਼ਨਮਭ Cਮਭਣਨਲ਼ਨਮਭਲ


Temperature: 50°F (10°C) minimum, 100°F (38°C)
Surface must be clean, dry, and in sound condition. Remove all maximum
oil, dust, grease, dirt, loose rust, and other foreign material to (air, surface, and material)
ensure adequate adhesion. At least 5°F (2.8°C) above dew point
Do not use hydrocarbon solvents for cleaning. Relative humidity: 85% maximum
Concrete and Masonry Aਯਯਫਨਢਠਲ਼ਨਮਭ Eਰ਴ਨਯਬਤਭਲ਼
For surface preparation, refer to SSPC-SP13/NACE 6, or ICRI No.
310.2R, CSP 1-3. Surfaces should be thoroughly clean and dry. The following is a guide. Any reduction must be compliant with
Concrete and mortar must be cured at least 28 days @ 75°F (24°C). existing VOC regulations and compatible with the existing enviro-
Remove all loose mortar and foreign material. Surface must be mental and application conditions.
free of laitance, concrete dust, dirt, form release agents, moisture
curing membranes, loose cement and hardeners. Fill bug holes, air Reducer/Clean Up ...........Water
pockets and other voids with Steel-Seam FT910. Primer required. Clear/Ultradeep tint base
requires reduction of 5% by volume
Follow the standard methods listed below when applicable:
ASTM D4258 Standard Practice for Cleaning Concrete. Brush
ASTM D4259 Standard Practice for Abrading Concrete. Brush..............................Nylon/Polyester or Natural Bristle
ASTM D4260 Standard Practice for Etching Concrete. Reduction .......................as needed up to 10% by volume, for
ASTM F1869 Standard Test Method for Measuring Moisture Vapor primer coat only
Emission Rate of Concrete.
SSPC-SP 13/Nace 6 Surface Preparation of Concrete. Roller
ICRI No. 310.2R Concrete Surface Preparation. Cover .............................1/4"-3/8" woven with solvent resistant
core
Wood Reduction .......................as needed up to 10% by volume, for
Surface must be clean, dry and sound. Remove any oils and dirt primer coat only
from the surface using a degreasing solvent or strong detergent.
Sand to remove any loose or deteriorated surface wood and to ob-
tain a proper surface profile. Prime with recommended primer and
If specific application equipment is not listed above, equivalent
paint as soon as possible. No painting should be done immediately
equipment may be substituted.
after a rain or during foggy weather. Knots and pitch streaks must
be scraped, sanded and spot primed before full coat of primer is
applied. All nail holes or small openings must be properly caulked.

Previously Painted Surfaces


If in sound condition, clean the surface of all foreign material.
Smooth, hard or glossy coatings and surfaces should be dulled by
abrading the surface. Apply a test area, allowing paint to dry one
week before testing adhesion. If adhesion is poor, or if this product
attacks the previous finish, removal of the previous coating may be
necessary. If paint is peeling or badly weathered, clean surface to
sound substrate and treat as a new surface as above.

Surface Preparation Standards


Condition of ISO 8501-1
Surface BS7079:A1 SSPC NACE
White Metal Sa 3 SP 5 1
Near White Metal Sa 2.5 SP 10 2
Commercial Blast Sa 2 SP 6 3
Brush-Off Blast Sa 1 SP 7 4
Hand Tool Cleaning Rusted
Pitted & Rusted
C St 2
D St 2
SP 2
SP 2
-
-
Power Tool Cleaning Rusted
Pitted & Rusted
C St 3
D St 3
SP 3
SP 3
-
-

www.sherwin-williams.com/protective continued on back


ArmorSeal ARMORSEAL® 8100
Heavy WATER BASED EPOXY FLOOR COATING
Duty Floor
Coatings P
P
A
A
B70-8100 S
B70-8160 S
G
S
P B B70V8100 H
Revised: November 4, 2019 A B 8.18

Aਯਯਫਨਢਠਲ਼ਨਮਭ P਱ਮਢਤਣ਴਱ਤਲ Pਤ਱ਥਮ਱ਬਠਭਢਤ Tਨਯਲ


During the early stages of drying, the coating is sensitive to rain,
Surface preparation must be completed as indicated. dew, high humidity, and moisture condensation. Plan painting
schedules to avoid these influences during the first 16-24 hours
Mix contents of each component thoroughly with low speed power
agitation. Make certain no pigment remains on the bottom of the of curing.
can. Then combine four parts by volume of Part A with one part
by volume of Part B. Thoroughly agitate the mixture with power Spreading rates are calculated on volume solids and do not include
agitation. an application loss factor due to surface profile, roughness or po-
rosity of the surface, skill and technique of the applicator, method
If reducer is used, add only after both components have been of application, various surface irregularities, material lost during
thoroughly mixed. mixing, spillage, overthinning, climatic conditions, and excessive
Apply paint at the recommended film thickness and spreading film build.
rate as indicated below:
For Clear applications, use the Ultra Deep Base, reduce 5%
Recommended Spreading Rate per coat: with potable water. When first mixed and applied, the mate-
Minimum Maximum rial is white, but will dry Clear. DO NOT exceed 10 mils WFT.
Wet mils (microns) 5.0 (125) 12.0 (300) Avoid puddling material at edges or in depressions as it may
Dry mils (microns) 2.0 (50) 5.0 (125) not dry clear.
~Coverage sq ft/gal (m2/L) 130 (3.3) 320 (8.1)
NOTE: Brush or roll to cove base or vertical surfaces may require
Excessive reduction of material can affect film build, appearance,
multiple coats to achieve maximum film thickness and uniformity of and adhesion.
appearance.
Do not apply the material beyond recommended pot life.
Drying Schedule @ 7.0 mils wet (175 microns):
@ 50°F/10°C @ 77°F/25°C @ 120°F/49°C Do not mix previously catalyzed material with new.
50% RH
To touch: 1 hour 1 hour 30 minutes Always test adhesion by applying a test patch of 2-3 square feet.
To recoat*: Allow to dry one week before checking adhesion.
minimum: 8 hours 6 hours 3 hours
maximum: 72 hours 72 hours 72 hours Do not use hydrocarbon solvents for cleaning.
To Cure 7 days 7 days 7 days
Foot Traffic: 36 hours 18 hours 8 hours Anti-slip additives, such as H&C SharkGrip® or Armorseal Hi-Wear
Drying time is temperature, humidity, and film thickness dependent. Additive, may be added to the coating to provide some slip resis-
*If recoating after 72 hours, abrade surface first. tance. This product should not be used in place of a non-skid finish.
Pot Life: 8 hours 5½ hours 3½ hours
Sweat-in-Time: None None None
Refer to Product Information sheet for additional performance
Application of coating above maximum or below minimum
recommended spreading rate may adversely affect coating characteristics and properties.
performance.
Sਠਥਤਲ਼ਸ P਱ਤਢਠ਴ਲ਼ਨਮਭਲ
Cਫਤਠਭ Uਯ Iਭਲਲ਼਱਴ਢਲ਼ਨਮਭਲ Refer to the SDS sheet before use.
Clean spills and spatters immediately with soap and warm water.
Clean hands and tools immediately after use with soap and warm Published technical data and instructions are subject to change without notice.
water. Contact your Sherwin-Williams representative for additional technical data and
instructions.
Dਨਲਢਫਠਨਬਤ਱
The information and recommendations set forth in this Product Data Sheet are
Wਠ਱਱ਠਭਲ਼ਸ
based upon tests conducted by or on behalf of The Sherwin-Williams Company. The Sherwin-Williams Company warrants our products to be free of manufacturing
Such information and recommendations set forth herein are subject to change and defects in accord with applicable Sherwin-Williams quality control procedures.
pertain to the product offered at the time of publication. Consult your Sherwin- Liability for products proven defective, if any, is limited to replacement of the de-
Williams representative to obtain the most recent Product Data Information and fective product or the refund of the purchase price paid for the defective product
Application Bulletin. as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

www.sherwin-williams.com/protective

You might also like