Product Data

HEMPADUR MULTI-STRENGTH 45753

Low to medium temperatures 45753: BASE 45755 : CURING AGENT 98750

Description: HEMPADUR MULTI-STRENGTH 45753 is a self-priming, two-component, highbuild, pure epoxy paint
which cures to an abrasion and corrosion resistant coating.
Recommended use: As a heavy duty coating for areas exposed to abrasion and aggressive corrosive climate such as ramps,
ship hulls and holds of bulk carriers.
As a ballast tank coating for special purposes such as chemical carriers carrying hot cargoes and other
purposes where “pure epoxy coating” is requested.
As a finishing coat where a cosmetic appearance is of less importance.
HEMPADUR MULTI-STRENGTH 45753 is intended for use in cold climates - see APPLICATION
CONDITIONS overleaf.
Service temperature: Maximum, dry exposure only: 140°C/284°F
In water (no temperature gradient): 50°C/122°F
Other liquids: Contact HEMPEL
Certificates/Approvals: HEMPADUR MULTI-STRENGTH 45753 tested by Teknologisk Institut AS, Norway, and approved for
internal use in pipe lines for water power generation according to NS 5417.
Recognized Abrasion Resistant Ice Coating by Lloyds Register.
Complies with EU Directive 2004/42/EC: subcategory j.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 12340* / Grey.
Finish: Semi-gloss
Volume solids, %: 79 ± 1
Theoretical spreading rate: 4 m2/l [160.4 sq.ft./US gallon] - 200 micron/8 mils
Flash point: 27 °C [80.6 °F]
Specific gravity: 1.6 kg/litre [13.2 lbs/US gallon]
Surface-dry: 2 hour(s) 20°C/68°F
Through-dry: 4 hour(s) 20°C/68°F
Fully cured: 14 day(s) 10°C/50°F
VOC content: 234 g/l [1.9 lbs/US gallon]
- *other shades according to assortment list.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

APPLICATION DETAILS:
Version, mixed product: 45753
Mixing ratio: BASE 45755 : CURING AGENT 98750
3 : 1 by volume
Application method: Airless spray / Brush / Roller
Thinner (max.vol.): 08450 (5%) /08450 (5%) /08450 (5%) (Consult the separate APPLICATION INSTRUCTIONS)
Pot life: 1 hour(s) 20°C/68°F
Nozzle orifice: 0.021 - 0.023 "
Nozzle pressure: 250 bar [3625 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 200 micron [8 mils] see REMARKS overleaf
Indicated film thickness, wet: 250 micron [10 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-

Date of issue: July 2019 Page: 1/2

Product Data
HEMPADUR MULTI-STRENGTH 45753

SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1:
2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10,
Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G).
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material
by abrasive blasting or power tool cleaning. Feather edges to sound and intact areas. After wet
abrasive blasting hose down the surface with fresh water and allow drying. Touch up bare spots with:
specified HEMPADUR paint
APPLICATION CONDITIONS: Use only where application and curing can proceed at temperatures between: -10°C/14°F - 20°C/68°F.
The temperature of the paint itself should be above: 15°C/59°F. Apply only on a dry and clean surface
with a temperature above the dew point to avoid condensation. In confined spaces provide adequate
ventilation during application and drying. Curing requires a relative humidity of: max. 85%.
PRECEDING COAT: None, or as per specification.
SUBSEQUENT COAT: None, or as per specification. Recommended systems are: HEMPADUR or HEMPATHANE
REMARKS:
VOC - EU Directive 2004/42/EC:
Not available.
Product As supplied 5 vol. % thinning Limit phase II, 2010
4575312340 234 g/l 265 g/l 500 g/l
For VOC of other shades, please refer to Safety Data Sheet.
Colours/Colour stability: Has a tendency to yellow after application. This will have no influence on the performance.
Weathering/service temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more sensitive to
mechanical damage and chemical exposure at elevated temperatures is also reflected in this product.
Application equipment: It is recommended to use heavy airless spray equipment with a pump transmission rate of 60:1
(approximately), and a theoretical output of min. 12 litres per minute.
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
150-300 micron/6-12 mils
Thinning: Normally not to be diluted.
Curing agent: The curing agent 98750 has a tendency to become darker at storage. This has no influence on
performance, but may influence the shade of the mixed product.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.

A specification supersedes any guideline overcoat intervals indicated in the table.

Environment Atmospheric, severe
Surface temperature: -10°C (14°F) 0°C (32°F) 20°C (68°F)
Min Max Min Max Min Max
HEMPADUR 45 h 90 d 22.5 h 90 d 5h 30 d
HEMPATEX 45 h 4½ d 22.5 h 54 h 5h 12 h
HEMPATHANE 54 h 27 d 27 h 13.5 d 6h 3d
Environment Immersion
HEMPADUR 54 h 90 d 27 h 90 d 6h 30 d
NR = Not Recommended, Ext. = Extended, m = minute(s), h = hour(s), d = day(s)

Overcoating note: The coating is to be checked carefully and any patchy, whitish, and/or greasy formation, must be
completely removed by suitable cleaning method.

The long maximum overcoating interval for HEMPADUR will be reduced if the coating is more than just
scarcely exposed to direct sunshine before overcoating.
If the interval is exceeded, roughening of surface is necessary to ensure intercoat adhesion.
Note: HEMPADUR MULTI-STRENGTH 45753 For professional use only.
ISSUED BY: HEMPEL A/S 4575312340
X Move PDS Disclaimer to Second page
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.

Date of issue: July 2019 Page: 2/2