Scribd
Upload
1K views17 pages

Logik 9

The Logik 9 controller is an electronic control device suitable for operating low-to-medium size screw compressors. It has inputs for temperature and pressure sensors and 4 digital inputs that can be configured as needed. It provides 5 relay outputs to control components like contactors. The Logik 9 has alarms for issues like high temperature, pressure switches, and maintenance timers. It displays operating parameters on its control panel and allows communication via RS485 to integrate into multi-unit and SCADA systems. Password protection secures access to risky parameters.

Uploaded by

Ramsi Sembiring
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views17 pages

Logik 9

The Logik 9 controller is an electronic control device suitable for operating low-to-medium size screw compressors. It has inputs for temperature and pressure sensors and 4 digital inputs that can be configured as needed. It provides 5 relay outputs to control components like contactors. The Logik 9 has alarms for issues like high temperature, pressure switches, and maintenance timers. It displays operating parameters on its control panel and allows communication via RS485 to integrate into multi-unit and SCADA systems. Password protection secures access to risky parameters.

Uploaded by

Ramsi Sembiring
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

LOGIK 9 CONTROLLER

GENERAL INFORMATION

Logik 9 is an industrial electronic control device


suitable for the operation of low-medium size
screw compressors with basic functions.

Thanks to the input for pressure transducer,


settable via software, Logik 9 allows to operate
the compressor also by electromechanical
pressure switch.

Directives and Limits

 Conformity to EC and UL 508 regulation


 Black auto-extinguishing box in ABS a) according EC: IP64 for the front panel and IP20 for the
other parts; b) according UL: Type 1 and Type 12 for front panel mounting, installation in
pollution degree 2 for the other parts
 Working temperature: - 10°C (14°F) ÷ 50°C (122°F) 90% RH (non condensing)
 Power supply: 12Vac ± 15% 50 ÷ 60 Hz
LOGIK 9 – Inputs & Outputs

Analog Inputs : Digital Outputs :


• 2 Analog inputs • 5 relay outputs
Digital Inputs : Serial Interface :
• 4 opto isolated digital inputs • RS485 supporting Modbus RTU
LOGIK 9 – Inputs & Outputs

Power supply : Digital Inputs :


• 12 Vac ± 10%
• Input 1 : Emergency Stop Button
Analog Inputs : • Input 2 : Motor Thermal Overload
• Analog input 1 : Temperature Probe • Input 3 : Phase Control Relay
• Analog input 2 : Pressure Transducer • Input 4 : Remote Start/Stop
Unused digital inputs can be configured according to needs
LOGIK 9 – Inputs & Outputs

Power supply : Digital Inputs :


• 12 Vac ± 10%
• Input 1 : Emergency Stop Button
Analog Inputs : • Input 2 : Motor Thermal Overload
• Analog input 1 : Temperature Probe • Input 3 : Phase Control Relay
• Analog input 2 : Pressure Transducer • Input 4 : Remote Start/Stop
Unused digital inputs can be configured according to needs
LOGIK 9 – Inputs & Outputs

Digital Outputs : Alarm Relay (Output 5) :

• Output 1 : Line Contactor Thanks to special software it possible to


• Output 2 : Start Contactor take alarm and warning informations by
• Output 3 : Delta Contactor using just 1 relay.
• Output 4 : Load Selenoid
LOGIK 9 – Alarms

Alarm Method
• Phase Rotation (Digital input)
• Generic Alarm (Digital input)
• High Temperature Alarm (Parameter)
• High Temperature Warning (Parameter)
• Temperature Probe Failure (Connectiviy check)
• Low Temperature (Parameter)
LOGIK 9 – Alarms

Alarm Method
• Power Failure (Measurement)
• Starts/hour (Parameter)
• Security Pressure Switch (Digital Input)
• High Pressure Alarm (Parameter)
• Transducer Failure (Connectivity Check)
• Emergency Stop Button (Digital Input)
LOGIK 9 – Maintenance

Each maintenance timers can be set by • F-A : Air Filter Change


using the parameters • F-O : Oil Filter Change
• F-S : Separator Filter Change
• OIL : Oil Change
• C-H : Check the Compressor
• b-L : Lubricate Bearings
LOGIK 9 – The Control Panel & Visualizations

The logik9 serves the regarding informations


into different groups that user can easily
observe the important informations and
measurements separately.

Group 1 : The working pressure


Group 2 : Pressure measurement unit
Group 3 : The working temperature
Group 4 : This menu visualize the parameter
sub menu code.
LOGIK 9 – The Control Panel & Visualizations

Each icon on the screen informs the user about


current changes of the regarding inputs and
outputs.

- Pressure unit selection Psi / Bar


- Temperature unit selection °F / °C

1: The fan is on icon


2: The load selenoid valve is energized
3: Remote Start / Stop input opens
4: An alarm occured in the system
5: Maintenance timer is elapsed
6: The temperature measurement unit
7: Master / Slave working mode
LOGIK 9 – Password Protection

Logik9 has different password levels regarding


to menu access permissions.

Thanks to this special password protection


design, the risky and important parameters
security is provided.
LOGIK 9 – Communication

Logik9 has 1 RS485 serial communication port that allows to communicate under ;
• Master / Slave Mode
• Multiunit
• Scada Systems
• Cloud Server
• Webserver
LOGIK 9 – Master/Slave Communication

Master / Slave communication functions :


• Balance Hours : Two compressors can be managed to balance the working hours
• Cascade working system with two compressors : By proper parameter settings user can
design cascade system where one compressor capacity is not sufficient to provide
pressurized air.

Logik9 Logik33S Logik26S

RS485 line
Modbus Rtu Protocol
LOGIK 9 – Multiunit Communication

Multiunit Communication Functions:


• Balance Hours : the working hours can be balanced
• Priority : Its possible to assing to compressor a priority
• Smart Mode : According to air consumption, the multiunit system selects the energy
saving combination with the compressor capacities.
Logik200 Multiunit Controller

RS232-RS485
Converter

RS485 line
Modbus Rtu Protocol

Logik9 Logik33S Logik26S


Up to 12 units can be controlled
LOGIK 9 – Ethernet Serial Gateway Functions

Ethernet Serial Gateway:


• Embedded webserver mode: the compressor plant monitoring
• Cloud based mode : the compressor plant monitoring by using internet connection
• Modbus RTU -> Modbus TCP converter

Serial Ethernet Interface TCP/IP – WebServer Interface

Modbus RTU / Modbus TCP

RS485 line
Modbus Rtu Protocol Cloud – Server

TCP/IP – WebServer Interface

Up to 12 units can be connected


Thank You …

You might also like