Scribd
Upload
241 views8 pages

Displays: Specifications FOR LCD Module CGM12864

This document provides specifications for an LCD module model CGM12864 including its features, mechanical parameters, electrical characteristics, pin assignments, block diagram, and control commands. The module has a 128 x 64 dot graphic LCD with a built-in HD61202 controller IC and operates at 14.43V. It measures 78.0W x 70.0H x 9.2 mm and has options for EL or LED backlighting. The document outlines the module's pin functions, voltage levels, and timing characteristics for reading and writing display data.

Uploaded by

Diego Azevedo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
241 views8 pages

Displays: Specifications FOR LCD Module CGM12864

This document provides specifications for an LCD module model CGM12864 including its features, mechanical parameters, electrical characteristics, pin assignments, block diagram, and control commands. The module has a 128 x 64 dot graphic LCD with a built-in HD61202 controller IC and operates at 14.43V. It measures 78.0W x 70.0H x 9.2 mm and has options for EL or LED backlighting. The document outlines the module's pin functions, voltage levels, and timing characteristics for reading and writing display data.

Uploaded by

Diego Azevedo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

ME DISPLAYS

SPECIFICATIONS

FOR

LCD MODULE

CGM12864

MICRO ELECTRONICS CORPORATION


3375 Scott Blvd. Suite 222 Santa Clara CA 95054
Tel: 408-988-1101 Fax: 408-988-7626
Email: [email protected]
Http://www.microelect.com

This datasheet has been downloaded from http://www.digchip.com at this page


ME DISPLAYS CGM12864
128 x 64 dots Graphic

• FEATURES
Number of Dots 128 x 64
Built-in Controller IC HD61202
Duty Cycle 1/64 Duty
Biasing 1/9 Biasing
Operating Voltage 14.43V
Glass to PCB Zebra and Heat Seal
Connector
Options EL/LED Backlight, STN

• MECHANICAL PARAMETERS
Module Size 78.0W x 70.0H x 9.2 mm
Viewing Area Size 62.0W x 44.0H mm
Dot Size 0.55 x 0.39 mm
Dot Pitch 0.60 x 0.44 mm

• ABSOLUTE MAXIMUM
Item Symbol Min. Max Unit
Power Supply Voltage Vdd -0.3 +7.0 V
Power Supply for LCD Drive Vlcd Vdd-19.0 Vdd+0.3 V
Input Voltage Vi -0.3 Vdd+0.3 V
Operating Temperature Ta -10 +60 C
Storage Temperature Tstg -20 +70 C

• ELECTRICAL CHARACTERISTICS
(Vdd=5.0V ± 10%, Ta=25C)
Item Symbol Conditions Min Typ Max U
Power Supply for Logic Vdd -- 4.5 5.0 5.5 V
Input “High” Voltage Vih E, R/W, RS 2.0 -- Vdd V
Input “Low” Voltage Vil DB0-DB7 0 -- 0.8 V
Output “High” Voltage Voh DB0- 2.4 -- - V
Output “Low” Voltage Vol DB7 - - 0.4 V
Power Supply Current Idd During Display - -- 2750 uA

Micro Electronics Corp Http://www.microelect.com


ME DISPLAYS CGM12864
128 x 64 dots Graphic

• PIN ASSIGNMENT

No. Symbol Level Function


1 CSA -- Chip Selection
2 CSB -- Chip Selection
3 GND -- Power Ground (0V)
4 Vcc -- Supply Voltage (+5V)
5 Vee -- Supply Voltage for LCD (0 ~ -10V)
6 D/I H, HàL H: Data, L: Instruction
7 R/W H/L H: Read, L: Write
8 E H/L Enable Signal
9 DB7 H/L Data Bus
10 DB6 H/L Data Bus
11 DB5 H/L Data Bus
12 DB4 H/L Data Bus
13 DB3 H/L Data Bus
14 DB2 H/L Data Bus
15 DB1 H/L Data Bus
16 DB0 H/L Data Bus

• BLOCK DIAGRAM
• DIAGRAM CGM12864
• BACKLIGHT CHARASTERISTICS

EL BACKLIGHT
Electrical Data
Parameter Description
Power Supply Up to max. 230 RMS
Wave Shape Sinusoidal
Frequency Up to max. 3 KHz
Efficiency η (dvA/cd)
Capacity 0.50 nF/cm2
Operating Current 160mA

Optical Data
Parameter Description
Power Supply 110v 400Hz sinusoidal
Luminous Intensity 69.3 cd/m2 resp 20.4fl
Emission Color Green/Blue 500nm
x=0.173, y=0.407
Homogenity ± 5%
Useful Life Unlimited
Brightness Uniformity 1000h approx. 80%
(Relative Humidity <80%) 5000h approx. 50%
LED BACKLIGHT
Characterisitcs
Low Voltage Driving (DC) is available without invertor
No noise occurrence
Life : 20K Hours

Item Symbol Conditions Min Typ. Max. Unit


Power Dissipation Po -- 1.1 W
Reverse Current IR VR=8V -- -- 0.2 mA
Reverse Voltage VR -- -- 8 -- V
Peak Forward Current IF -- -- 250 -- mA
Forward Voltage VF IF=100mA -- 4.2 4.4 V
Luminous Intensity IV TA=25C -- 14 -- cd/m2

• AC CHARACTERISTICS
(Vdd=5V ± 10%, Vss=0V, Ta=25°C)
Item Symbol Min Max Unit
Enable Cycle Time TCYC 1000 -- ns
Enable Pulse Width PWEH, PWEL 450 -- ns
Enable Rise/Fall Time tEr, tEf -- 25 ns
Address Set-up Time tAS 140 -- ns
Address Hold Time tAH 10 -- ns
Data Set-up Time tDSW 200 -- ns
Data Delay Time tDDR -- 320 ns
Data Hold Time (Writing) tDHW 10 -- ns
Data Hold Time (Reading) tDHR 20 -- ns
• TIMING CHARACTERISTICS

Micro Electronics Corp Http://www.microelect.com


• CONTROL AND DISPLAY COMMAND
Command R/ D/I DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Remark
W
Display on/off L L L L H H H H H L/H Controls the display on or
off. Internal status and
display RAM data is not
affected. L: OFF, H: ON
Set Address L L H H Y address (0~63) Sets the Y address in the Y
address counter
Set Page (X L L H L H H H page (0~7) I/D: Set Cursor Move
Address) Direction
H-Increase L-Decrease
SH: Specifies Shift of
Display
H-Display is Shifted
L-Display is Not Shifted
Display Start L L H H Display start line (0~63) D: Display (H-on, L-off)
Line C: Cursor (H-on, L-off)
B: Blinking (H-o, L-off)
Status Read H L Bus L On/ Re L L L L Read the status:
y Off set busy 1: working, 0: ready
ADC 1: clockwise output, 0:
counterclockwise
On/Off 1: disp off, 0: disp on
Reset 1: reset, 0: normal
Write Display L H Write Data Write data (DB0:7) into
Data display data RAM. After
writing instruction, Y address
is increased by 1
automatically
Read Display L L Read Data Read data (DB0:7) from
Data display data RAM to the
data bus

You might also like