4007ES and 4007ES Hybrid Fire Alarm Systems: Installation Manual 579-1102 Rev. E

4007ES and 4007ES Hybrid
Fire Alarm Systems
Installation
Manual
579-1102
Rev. E
Copyrights, Trademarks, Cautions, Warnings, and Regulatory Info
Copyrights and ©2015-2016 Tyco Fire Protection Products. All rights reserved.
Trademarks
Specifications and other information shown were current as of publication and are subject to
change without notice. TYCO, SIMPLEX, and the product names listed in this material are
marks and/or registered marks. Unauthorized use is strictly prohibited.
Cautions and READ AND SAVE THESE INSTRUCTIONS- Follow the instructions in this installation manual. These instructions must
be followed to avoid damage to this product and associated equipment. Product operation and reliability depend upon proper
Warnings installation.
DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED- Upon unpacking your Simplex
product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier
and notify an authorized Simplex product supplier.
ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or repairs. All repairs
should be performed by a representative or authorized agent of your local Simplex product supplier.
STATIC HAZARD - Static electricity can damage components. Handle as follows:

• Ground yourself before opening or installing components.
• Prior to installation, keep components wrapped in anti-static material at all times.
EYE SAFETY HAZARD - Under certain fiber-optic application conditions, the optical output of this device may exceed eye
safety limits. Do not use magnification (such as a microscope or other focusing equipment) when viewing the output of this
device.
SULFURIC ACID WARNING- Battery contains sulfuric acid, which can cause severe burns to the skin and eyes and can
destroy fabric. Replace any leaking or damaged battery while wearing appropriate protective gear. If you come in contact with
sulfuric acid, immediately flush skin or eyes with water for 15 minutes and seek immediate medical attention.
FCC RULES AND REGULATIONS – PART 15 - This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES - To ensure proper system operation, this product must be tested in
accordance with NFPA-72, after any programming operation or change in site-specific software. Reacceptance testing is required after any change,
addition or deletion of system components, or after any modification, repair or adjustment to system hardware or wiring.
All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that
other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50
devices, must also be tested and proper system operation verified.
Table of Contents
Copyrights, Trademarks, Cautions, Warnings, and Regulatory Info......................................i-2

Chapter. 1 Overview....................................................................................................1-1
Introduction ........................................................................................................................................... 1-1
In this chapter ....................................................................................................................................... 1-1
4007ES Product List ............................................................................................................................. 1-1
Glossary................................................................................................................................................ 1-2
User Interface ....................................................................................................................................... 1-2
Chapter. 2 Installation.................................................................................................2-1
Introduction ........................................................................................................................................... 2-1
In this chapter ....................................................................................................................................... 2-1
Mounting the 4007ES Panels ............................................................................................................... 2-1
Trim Kit ........................................................................................................................................2-2
Trim Kit Application ............................................................................................................................... 2-2
Wiring ..........................................................................................................................................2-3
Wiring Guidelines.................................................................................................................................. 2-3
Safety Ground....................................................................................................................................... 2-4
AC Supply Wiring.................................................................................................................................. 2-4
Battery Guidelines................................................................................................................................. 2-4
Power...........................................................................................................................................2-5
Final Installation .................................................................................................................................... 2-5
Chapter. 3 NAC Power Supply ...................................................................................3-1

Introduction ........................................................................................................................................... 3-1
In this chapter ....................................................................................................................................... 3-1
NAC Power Supply Specifications............................................................................................3-2
Power Supply Specifications................................................................................................................. 3-2
NAC Section ................................................................................................................................3-3
NAC Section Overview ......................................................................................................................... 3-3
Specifications........................................................................................................................................ 3-3
Wiring.................................................................................................................................................... 3-3
Troubleshooting .........................................................................................................................3-6
Troubleshooting .................................................................................................................................... 3-6
Chapter. 4 IDNAC Power Supply................................................................................4-1

Introduction ........................................................................................................................................... 4-1
In this Chapter....................................................................................................................................... 4-1
IDNAC Power Supply Specifications ........................................................................................4-2
Power Supply Specifications................................................................................................................. 4-2
IDNAC Section ............................................................................................................................4-3
IDNAC Section Overview...................................................................................................................... 4-3
Specifications........................................................................................................................................ 4-3
Wiring.................................................................................................................................................... 4-3
iii
Table of Contents
Compatible Devices and Appliances .................................................................................................... 4-6

Auxiliary Relays Section ............................................................................................................4-8
Auxiliary Relays Section Overview ....................................................................................................... 4-8
SLC Channel Trouble LED Codes ........................................................................................................ 4-9
System Trouble LED Codes ............................................................................................................... 4-10
Chapter. 5 4007ES Power Supplies ...........................................................................5-1

Introduction ........................................................................................................................................... 5-1
In this chapter ....................................................................................................................................... 5-1
Power Supplies Specifications.............................................................................................................. 5-1
Wiring Guidelines.................................................................................................................................. 5-1
IDNet Section ..............................................................................................................................5-2
IDNet Section Overview........................................................................................................................ 5-2
Specifications........................................................................................................................................ 5-2
Device Addressing (Class A and Class B)............................................................................................ 5-2
Wiring.................................................................................................................................................... 5-3
Auxiliary Power Section.............................................................................................................5-5
AUX PWR/SNAC Overview .................................................................................................................. 5-5
RUI Section .................................................................................................................................5-7
RUI Overview........................................................................................................................................ 5-7
Chapter. 6 Optional Modules and Cards ...................................................................6-1

Introduction ........................................................................................................................................... 6-1
In this chapter ....................................................................................................................................... 6-1
8-point Zone/Relay Card....................................................................................................................... 6-1
25V Regulator Module .......................................................................................................................... 6-1
IDNet+ Loop Expansion Card ............................................................................................................... 6-1
LED Module .......................................................................................................................................... 6-1
SDACT Card ......................................................................................................................................... 6-1
City Circuit............................................................................................................................................. 6-1
Alarm Relay Card.................................................................................................................................. 6-2
TrueInsight Service Gateway................................................................................................................ 6-2
Dual Class A Isolator ............................................................................................................................ 6-2
Example of Combinations ..................................................................................................................... 6-2
Appendix. A ULC Programming Requirements ...................................................... A-1
iv
Chapter 1
Overview
Introduction The 4007ES fire alarm control panel provides audible and visible indication of alarms,
troubles, and supervisory conditions. The 4007ES panels supports addressable notification
and initiating devices and the 4007ES Hybrid panels supports non-addressable notification
devices and addressable initiating devices*. The panel can be configured by using a panel
programmer.
*From this point on, the 4007ES and the 4007ES hybrid will be referred to as 4007ES, unless
stated otherwise.
4007ES operator instructions are described in the 4007ES Operator’s Manual, 579-1165.
4007ES programming instructions are described in the 4007ES Programmer’s manual,
579-1167.
In this chapter 4007ES Product List ............................. 1-1 Glossary ................................................ 1-2
User Interface........................................ 1-2
4007ES Product
Part Number Base Panels
List
4007-9101 4007ES Hybrid, Red
4007-9201 4007ES, Red
4007-9102 4007ES Hybrid, Platinum
4007-9202 4007ES, Platinum
Part Number Optional Modules: Field Installed Manual
4007-9801 Zone/Relay Module 579-1103
4007-9802 25V Regulator Module 579-812
4007-9803 IDNet+ Loop Expansion Module 579-1106
4007-9804 Dual Class A Module 579-1029
4007-9805 LED Module 579-1105
4007-9806 DACT Module 579-954
4007-9807 City Circuit with Disconnect Module 579-955
4007-9808 City Circuit without Disconnect Module 579-955
4007-9809 Relay Module 579-955
4190-6106 TrueInsight Remote Service Gateway and Programming 579-953
1-1
Chapter 1 Overview
Overview, Continued
Glossary Term Definition

Aux Abbreviation for Auxiliary; typically used to describe Auxiliary Power.
EOL End-of-Line (typically in reference to and end-of-line resistor or EOL
resistor).
FACP Fire Alarm Control Panel.
Hybrid In this document, “Hybrid” the 4007ES Hybrid models that provide both
addressable and conventional initiation with conventional non
addressable Notification Appliance Circuits.
IDC Initiating Device Circuit.
IDNet Addressable SLC for up to 250 addressable devices.
IDNet+ IDNet which is electrically isolated from internal panel electronics.
IDNAC Individual Device Notification Appliance Circuit (Addressable).
NAC Notification Appliance Circuit (formerly called signal circuit).
Regulated 24 DC Notification appliance operation that meets the minimum listing
requirements; inrush currents typically require power supply and NAC
rating.
RUI Remote Unit Interface; SLC for communications with remote
annunciators.
Simple NAC A Reverse Polarity Supervised Notification Appliance Circuit that is
capable of on steady or coded operation. Sync or SmartSync operation
is not supported.
SLC Signaling Line Circuit
SmartSync A reverse polarity monitored NAC capable of synchronizing and
controlling both horns and strobes on the same circuit via a proprietary
signaling protocol. Used as the protocol for TrueAlert Non-Addressable
Devices.
User Interface The user interface is a 4.3” (109mm) diagonal color LCD with a built-in resistive touch panel
and 12 indicating LEDs. The color LCD provides system status and access to perform system
functions and to change the system configuration.
Figure 1-1 shows an inside view of the 4007ES panel with the optional LED module
(4007-9805) installed.
Figure 1-1. 4007ES Panel Inside View
1-2
Chapter 2
Installation
Introduction This chapter describes how to install the 4007ES panel. It can be semi-flush or surface mount.
In this chapter Mounting the 4007ES Panels ................2-1 Trim Kit Application .............................2-2
Safety Ground........................................2-4 AC Supply Wiring .................................2-4
Battery Guidelines.................................2-4 Final Installation ....................................2-5
Mounting the • Due to the danger of metal fragments

4007ES Panels falling into electronics when drilling Power Supply
the holes for the conduits, remove the

electronics in the system: Screws
- To remove the electronics, unscrew

the ten screws. Remove the power
supply and store it in a safe, clean, and
dry location until the panel installation
is completed, see Figure 2-1.
- If installing a 4007ES hybrid panel,
also remove the Zone/Relay card (three
screws).
• Use a suitable punch where conduit
entrance is required. Knockouts are not
provided. Locate and create on-site as
required during installation.
Figure 2-1 Screws location
• For surface or semi-flush mounting to a wooden wall structure, the panel must be attached
with four 1-½-inch-long (38 mm) lag bolts and four ½-inch-diameter (13 mm) washers
(supplied by others).
• For surface mounting, secure the box to the wall using the tear-drop mounting holes on
the back surface. For semi-flush mounting, secure the box (along the sides) to the wall
studs. Note that the front surface of the back box must protrude at least 1-1/2 inch (38mm)
inches from the wall surface for semi-flush installation. A trim kit is supplied for semi-
flush mounting. Refer to the Trim Kit Application section for more information.
• To install the panel refer to Figure 2-2 for the dimensions and use the holes in the back
box to secure it to the wall.
.
16” (406mm)
Mounting Holes
16-5/16”
(416mm)
20-3/16”
(512mm)
1-1/2” (38mm)
16’ (406mm)
20-7/8” (530mm)
Figure 2-2. Back Box Installation dimensions and Semi-Flush Mounting (Right)
2-1
Chapter 2 Installation
Trim Kit
Trim Kit Trim kits are used to cosmetically cover wall openings when boxes are mounted semi-flush
Application into the wall. The kit includes:
• Two top trim bands (shorter)
• Two side trim bands (longer)
• Four corner pieces.
Top Trim Bands (x2)
Corner Pieces (x4)
Side Trim Bands (x2)
Figure 2-3 Semi-Flush Trim Kit
After mounting the box semi-flush to the wall, attach the trim per the following procedure:
1. The strips need to be cut before being attached. Carefully
cut them to length using a hacksaw or sharp utility knife.
Cut the strips approximately 1" (25 mm) shorter than the
box dimension. The box is 20-7/8" (530 mm) wide and
20-3/16" (512 mm) high. Semi-Flush
2. Attach the strips one at the time. Peel off the adhesive tape Mounted
Back Box
release and center the strip on the box placing the edge of
the strip against the box surface, then press down solidly to
assure adhesion.
3. Each corner piece overlaps the trim strip slightly less than
3/4" (19 mm). Align the corner pieces tight to the box
corner and attach with a drywall or similar screw, suitable
for the wall material (screws are not supplied).
Figure 2-4. Applying the Trim
2-2
Wiring
Wiring Guidelines Follow these guidelines when connecting Power-Limited (PL) systems. For more information
about these guidelines, contact your authorized Simplex Product supplier.
• Non-Power Limited (NPL) field wiring (AC power, batteries, City connection, DACT)
must be installed and routed in the shaded areas shown in Figure 2-5.
• A minimum of 0.25 inches space must be maintained between NPL and PL field wiring.
• The AC Harness is pre-wired (tied to back of the box).
NPL Conduit Entry Side View of Panel
Optional Modules
Keep NPL wiring this

side of the box, strain
relieved to the back
of the box using the
lances shown.
Keep PL wiring in
this area for any
optional cards
mounted on this side
if NPL wiring is run
towards the top of
the box.
Keep battery wiring terminals

to the front of the box. If the DACT
or the City/Relay option card is
used, run 734-306 harness NPL conduit entry
wiring on the back of the box
to maintain separation from
battery wiring.
Figure 2-5. Field Wiring Guidelines (NAC Power Supply Shown as Reference)
• Conductors must test free of all grounds.
• A system ground must be provided for earth detection and lightning protection devices.
This connection must comply with approved earth detection per NFPA780.
• Splicing is permitted. All spliced connections must either be soldered (resin-core solder),
crimped in metal sleeves, or encapsulated with an epoxy resin. When soldering or crimped
metal sleeves are used, the junction must be insulated with a high-grade electrical tape that is
as sound as the original insulating jacket. Shield continuity must be maintained throughout.
• Excess slack should be kept to a minimum inside the back box enclosure. The wiring
should be neatly dressed and bundled together using wire ties.
• All wiring must be done using copper conductors only, unless noted otherwise.
• For IDNet, shielded wire is not recommended. If
shielded wires are present, cut and tape off the
shield at each end in the panel to prevent it from TO AUX POWER
coming in contact with other components. Metallic

continuity of the shield must be maintained and RED BLACK
insulated throughout the entire length of the cable. Note: 2098-9739

• If shielded wire is used, the metallic continuity of The 2098-9739 Relay is
used as an example.
END OF
LINE RELAY
the shield must be maintained throughout the entire Other UL Listed 24VDC
EOL relays can be used,
cable length and the entire length of the cable must depending on the application.
YELLOW
have a resistance greater than 1 megohm to earth
ground. Underground wiring must be free of all
water. IDC
LAST IDC
DEVICE
• In areas of high lightning activity, or in areas that
have large power surges, the 2081-9027 or the
2081-9044 Transient Suppressor should be used on
monitor points.
Figure 2-6. EOL Relay Diagram
2-3
Wiring
Wiring Guidelines • Wires must not be run through elevator shafts.

• Only system wiring can be run together in the same conduit.
When powering remote units through relay contacts, power for these circuits must be
provided by a PL power supply listed for fire-protective signaling use. An end-of-line
(EOL) relay must be used to supervise the auxiliary power circuit.
• Connect the output of the EOL Relay to cause a trouble. Wire in series with the EOL resistor
on an available Initiating Device Circuit (IDC) or Individual Addressable Module (IAM).
Safety Ground Proper operation and protection against transient energy per UL 864 and ULC-S527 requires
connection of safety ground wire to cabinet chassis. Connect safety ground before wiring any
other circuits to the panel.
AC Supply Wiring Adhere to the following guidelines when wiring AC Power.

• AC power must be wired from a dedicated circuit breaker or fuse, rated no more than
20 A, per NFPA-72, NEC, and local codes.
• Before handling AC feed, verify that it is not live using a voltmeter. Make sure the circuit
is de-energized and tagged to prevent injury.
• AC supply wiring must be 14 AWG minimum to 12 AWG maximum.
• Connect a 12 AWG copper ground wire from safety ground in the electrical distribution
panel to the panel safety ground stud.
• Input voltage:
- 120 VAC, 50/60 Hz
- 240 VAC, 50/60 Hz
- No configuration settings required to select.
Battery • A fused harness (harness 734-304 for NAC power supply and 734-303 for IDNAC power
Guidelines supply) is required to connect the backup batteries. That harness is shipped with the panel.
The mating spade lug on the battery should be 0.250” X 0.032". If another size is needed,
you will need to replace the battery terminal connectors on the supplied battery harness.
• The 4007ES battery charger supports up to 33 Ah batteries (maximum) within UL864 and
ULCS527 guidelines.
- 18 Ah batteries can fit inside the box.
- 25 Ah and 33 Ah batteries use 2081-9282 (red 25 Ah or 33 Ah) or 4009-9801 (beige
25 Ah)
• To minimize the power losses due to wiring from the external battery box to the 4007ES,
use at least a 12 AWG wire. Mount the battery box within 20 feet of the panel in
accordance with the mounting instruction label in the box. All interconnecting wiring must
be enclosed in conduit.
• Seismic battery brackets can be used internal to the 4007ES box (2081-9401 (12.7 Ah
bracket), 2081-9402 (18 Ah bracket)). For more information on how to install the seismic
brackets, refer to Battery Bracket installation instructions 579-944.
2-4
Power
Final Installation To finalize the installation:

1. Reinstall the power supply and the electronics.
2. Follow the steps below to
install the batteries:
a. Place the first battery on
the left side of the panel
to avoid interference
with the DACT (if
installed).
Note: SDACT
SDACT
The battery terminals should face
the front of the box.
b. Insert the second battery

and make sure it is
snugly positioned beside
the first battery.
c. Wire the batteries in
series such that you have
24 V. Use the white wire
provided to bridge the
SDACT
batteries together. (see
Figure 2-7).
IMPORTANT:
Verify all field
wiring before
applying any
power to the panel.
Power up the system:
1. Connect the negative lead Negative
Positive
to the battery.
Jumper
2. Apply AC.
3. Connect the positive to the
battery.
Figure 2-7. Power Supply
2-5
Chapter 3
NAC Power Supply
Introduction A conventional reverse polarity NAC power supply is used in a 4007ES hybrid panel. It
provides 6A and can support:
• Non-addressable notification devices
• Addressable initiating devices
Refer to Figure 3-1 and Table 3-1for the main components of the NAC power supply.
AUX/SNAC P1 NAC 1 NAC2 NAC3 NAC4

IDNet RUI
P1
1
2
B B
P2
1
2 A A
B B
A A
P2
TB1 TB2 TB3
LEDs
IDNet IDNet Zone/
Loop B Loop C J5
Relay
P4
LEDs P6
P8
25V P9
REG
Zone/ J15
Relay
J16
CPU J17 P11 TB4
P10
Option City/ BAT- BAT+

Relay
Figure 3-1. NAC Power Supply
Table 3-1. Main Components Information

P1 RUI Class A/B jumpers P2 IDNet Class A/B jumper
TB4 Battery connection TB2 NAC 1 and NAC 2
P10 AC Power Connection TB3 NAC 3 and NAC 4
J5 and J15 Zone / Relay J7 IDNet Loop B
J16 CPU Connection J8 IDNet Loop C
J17 Option Connection P4 NAC Power Supply Card On-line
P11 City/Relay Connection P6 Battery Depleted Jumper
P8 1-2 (default) / IDNet card on line
25V Regulator Jumpers 1-2, 3-4
IDNet Loop 1, Aux
TB1 default. Power is fed to the zone/
Power, RUI Connection P9
relay card. No jumpers. Using 4007-
9802, 25V Regulator Module.
In this chapter Power Supply Specifications.................3-2 NAC Section Overview ........................ 3-3
Specifications ........................................3-3 .............................................................. 3-3
Troubleshooting.....................................3-6
3-1
Chapter 3 NAC Power Supply
NAC Power Supply Specifications

Power Supply The NAC Power Supply can supply 6A of 24V power in addition to the base draw of the CPU/
Specifications Power Supply cards. The current draw taken from optional cards, IDNet Devices, Aux Power,
and NACs must be subtracted from 6A.
IMPORTANT: Refer to the 4007-9801 8-Point Zone/Relay Card

Installation Instruction, manual 579-1103, to determine the
draw of the pre-installed Zone/Relay card.
Table 3-2. 4007ES Hybrid System Current Draw
2 A at 120 VAC, 50/60Hz
Maximum AC Input
1 A at 240 VAC, 50/60Hz
Current
Standby Conditions
(Battery Standby 24 V)
No alarms (NACs normal). No IDNet devices connected. 145 mA
Add to above for each additional IDNet device in standby. 0.8 mA
Total current for fully loaded IDNet channel in standby. 345 mA
Current
Alarm Conditions
(Battery Alarm 24 V)
4 NACs ON: TBL Relay Activated: IDNet LED On. No

190 mA
IDNet devices connected.
Add to above for each IDNet device in alarm. 1 mA
Add to above for each IDNet LED On (20 maximum IDNet

2 mA
devices LEDs On).
Total current for fully loaded IDNet channel in alarm. 480 mA
3-2
NAC Section
NAC Section The NAC power supply allows connection to up to four Class A NAC circuits. Notification
Overview appliances within the 4007ES system are synchronized including any attached 4009 series
NAC extenders. Do not mix Wheelock and Simplex branded devices in the same system, they
will not be synchronized. The following TrueAlert non-addressable appliances are Special
Application compatible with the NAC power supply:
- 4098-9772 Sensor Base with 520 Hz Sounder
- 4098-9773 CO Sensor Base with 520 Hz Sounder
- 4901-series Horn
- 4903-series A/V
- 4903-series S/V
- 4904-series V/O
- 4906-Multicandela series
- 49CMT series Horn
- 49CMTV series A/V
- Wheelock Series: AS, HS, NS, ZNS, RSS, RSSP, STR, ZRS, MT, AMT, MTWP, ET,
CH, E50, E60, E70, E80, E90, S8, SA
NAC1 NAC2 NAC3 NAC4
B+ B- A+ A- B+ B- A+ A- B+ B- A+ A- B+ B- A+ A-
Figure 3-2. NAC Terminal on NAC Power Supply
Specifications Maximum Appliances 70 per circuit*

* Each 49CMT series appliance counts as 5 regular appliances for the maximum 70 appliances that
can be supported per NAC. As the earth fault sensitivity with thirteen MT appliances drops from 10
K to 9.6K ohms, no more than thirteen 49CMT series appliances may be placed on one circuit.
Electrical Specifications:
Voltage 24 VDC nominal
Alarm Current The maximum alarm current is 3 A per circuit.
Supervisory Current Refer to Table 3-4
Special Application Appliances
6 A total
(TrueAlert Non-Addressable)
Note: When NACs are used for Regulated 24DC appliances, maximum current per NAC is reduced to 2 A
and total power supply notification current rating is reduced to 3 A. Current used by modules pow-
ered from the 4007ES power supply must be deducted from the total current.
Wiring Wiring Parameters

The NAC Power Supply is supervised and power-limited. Refer to Table 3-4 for the NACs’
supported EOL resistors and the related supervisory current and to Table 3-3 for the wiring
parameters.
Note: If a shielded wire is used, cut it and tape it at both ends.
Table 3-4. Supported EOLR
Table 3-3. Wiring Parameters
and Supervisory Current
Maximum wiring distance EOLR Current
Maximum cable load 10,000 ft (3,048m) per channel 3.9 k 5.7 mA
Maximum wire length from
4,000ft (762m) 4.7 k 4.8 mA
panel to any device
Maintain correct polarity on terminal connections. Do not loop
5.1 k 4.4 mA
wires under terminals.
5.6 k 4.0 mA
10 k 2.2 mA
15 k 1.4 mA
Continued on next page
3-3
NAC Section, Continued
Wiring Wiring Distances

Table 3-5 lists the maximum distances from the NAC terminal block to the last appliance in a
Class A configuration, depending on wire gauge and current. Use Table 3-5 to calculate wire
distances for your application if you are using Class A wiring. Table 3-6 gives the values for a
Class B configuration.
Table 3-5. Class A Wiring Distances
Max Distance
Max Distance Max Distance Max Distance
w/ 14 DC
Alarm Current w/ 18 AWG w/ 16 AWG w/ 12 AWG
AWG Resistance
(0.8231 mm2) (1.309 mm2) (3.309 mm2)
(2.081 mm2)
0.25 A 420 ft (128 m) 667 ft (203 m) 1,063 ft (324 m) 1,691 ft (515 m) 6 Ohms
0.50 A 210 ft (64 m) 334 ft (102 m) 532 ft (162 m) 845 ft (258 m) 3 Ohms
1.00 A 105 ft (32m) 167 ft (51 m) 266 ft (81 m) 423 ft (129 m) 1.5 Ohms
1.25 A 84 ft (26 m) 133 ft (41 m) 213 ft (65 m) 338 ft (103 m) 1.2 Ohms
1.50 A 70 ft (21 m) 111 ft (34 m) 177 ft (54 m) 282 ft (86 m) 1 Ohm
1.75 A 60 ft (18 m) 95 ft (29 m) 152 ft (46 m) 242 ft (74 m) 0.86 Ohm
Table 3-6. Class B Wiring Distances
Max Distance Max Distance Max Distance Max Distance

w/ 18 AWG w/ 16 AWG w/ 14 AWG w/ 12 AWG DC
Alarm Current
Resistance
(0.8231 mm2) (1.309 mm2) (2.081 mm2) (3.309 mm2)
0.25 A 840 ft (256 m) 1,335 ft (407 m) 2,126 ft (648 m) 3,382 ft (1,031 m) 12 Ohms
0.50 A 420 ft (128 m) 667 ft (203 m) 1,063 ft (324 m) 1,691 ft (515 m) 6 Ohms
0.75 A 280 ft (85 m) 445 ft (136 m) 709 ft (216 m) 1,127 ft (344 m) 4 Ohms
3.00 A 70 ft (21 m) 111 ft (34 m) 177 ft (54 m) 282 ft (86 m) 1 Ohm
Note:
• Max Distance = distance from the power supply to last appliance.
• This table is calculated at 49 oC (120 oF). If you are installing in locations that could be exposed to
higher temperatures, refer to NEC Table 8.
• Distances are based on a 3 V drop, and take into account the worst-case panel output voltage.
• If circuit integrity wire is used instead of housing cable in a fire rated enclosure, reduce wiring distances
by 38 ft (12 m) for every 10 ft (3 m) of potential exposure.
Continued on next page
3-4
NAC Section, Continued
Wiring Class A Wiring

Note: The Class A wiring style is set up in the programmer. Refer to the 4007ES Programmer’s manual,
579-1167, for more information.
To connect the power BLK
supply to reverse-polarity, 2
RED
non-addressable 12 AWG (3.309 mm ) to
2
18 AWG (0.8231 mm )
notification appliances TYPICAL
using Class A wiring: APPLIANCE
1. Route wire from the RED BLK
“B+” and “B-” outputs of TYPICAL Leave the 378-030 EOL

APPLIANCE
the power supply to the Resistor (10 K Ohm, ½ W;
brown/black/orange) on
appropriate inputs on a unused circuits
peripheral notification
appliance. Use NAC1, RED BLK
NAC2, NAC3 or NAC4
(2.).
2. Route wire from the first
appliance to the next
one. Repeat for each B+ B- A+ A- B+ B- A+ A- B+ B- A+ A- B+ B- A+ A-
NAC1 NAC2 NAC3 NAC4
appliance.
Figure 3-3. Class A NAC Wiring

3. Route wire from the last appliance to the A+ and A- inputs on the same NAC circuit of the
power supply.
4. Repeat steps 1 through 3 for each NAC output you want to use.
5. Leave the 10 KOhms, ½ W, brown/black/orange resistor (378-030) on each unused circuit.
No external end-of-line resistor is needed for circuits in use.
Class B Wiring
Note: The Class B wiring style is set up in the programmer. Refer to the 4007ES Programmer’s
manual, 579-1167, for more information.
To connect the power 4081-9008 EOL Harness
10K 1/2W (133-894)
supply to appliances using
Class B wiring: RED BLK
RED
1. Route wire from the B+, TYPICAL
B- outputs on TB2 and APPLIANCE
TB3 of the power sup- RED BLK

RED
2
ply to the appropriate TYPICAL
12 AWG (3.309 mm ) to
2
18 AWG (0.8231 mm )
APPLIANCE
inputs on a peripheral Leave the factory installed
notification appliance. RED BLK
BLK
EOL Resistor (10 KOhms,
½ W, brown/black/orange)
Use NAC1, NAC2, on unused circuits
NAC3, or NAC4.
2. Route wire from the first
appliance to the next B+ B- A+ A- B+ B- A+ A- B+ B- A+ A- B+ B- A+ A-
one. “T” tapping is not NAC1 NAC2 NAC3 NAC4
allowed. Repeat for

each appliance.
Figure 3-4 Class B NAC Wiring
3. Route wire from the last appliance to the EOLR harness (10KOhms, 1/2 W: P/N 733-894).
4. Repeat steps 1 through 3 for each NAC output you want to use.
5. Leave the factory installed EOL Resistor (10 KOhms*, ½ W; brown/black/orange) on each
unused circuit. The circuit must connect “B+” to “B-” terminals.
6. Document EOL value in panel per circuit.
*If using a 4007ES hybrid panel, keep the original value and set the programmer accordingly.
3-5
Troubleshooting
Troubleshooting Table 3-7 gives the LED definition for the NAC power.
Table 3-7. 4007ES Hybrid Indicator LEDs
Aux/SNAC
Comm
Gen Power
NAC1
NAC2
NAC3
RUI TBL NAC4
LEDs
RUI OC
LEDs
Figure 3-5. LEDs on the 4007ES Hybrid Power Supply

LED10 AC Green. Off on AC failure
LED2 RUI Trouble Yellow. On for Class A RUI trouble
LED6 RUI OC Yellow. Indicates a short (overcurrent)
Yellow. Indicates that the communication between the NAC power sup-
LED3 Comm
ply and the CPU is lost
Steady On, yellow. Indicates AC power loss, earth fault, overcurrent
LED 4 Gen Power
and battery trouble
LED5, 7, 8, NAC 1, 2, 3,
Steady On, yellow. Used to signal overcurrent, short, and open
and 9 4
circuit.
Steady On, yellow. Use to signal overcurrent, short, and open

LED1 Aux/SNAC
circuit.
3-6
Chapter 4
IDNAC Power Supply
Introduction An IDNAC power supply is used in the 4007ES (non Hybrid) panel. It provides 4 A and can
support:
• Addressable notification devices
• Addressable initiating devices
Refer to Figure 4-1 and Table 4-1 for the main components of the IDNAC power supply.
AUX PWR/
IDNet SNAC RUI P1 IDNAC AUX RELAY 1 AUX RELAY 2
1
2
P1
P2 B B
1
2
B B A A
A A
P2
TB1 TB2 TB3 LEDs

P5
P4
IDNet IDNet
P5 Zone/
Loop C Loop B J7
Relay
P5
P8
P9
25V
REG J15
J16
CPU
J17 P11 TB4 5A Fuse
250VAC
Option City/ BAT- BAT+

Relay
Figure 4-1. IDNAC Power Supply
Table 4-1. Main Components Information

P1 RUI Class A/B jumpers P2 IDNet Class A/B jumper
TB4 Battery connection TB2 IDNAC
P10 AC Power Connection TB3 Aux Relay 1 and 2
DCAI
J15 J10 IDNet Loop 2
Zone/Relay Connection
J7 Zone/Relay J11 IDNet Loop 3
J16 CPU Connection P5 Battery Depleted Jumper
J17 Option Connection P8 1-2 (default) / IDNet card on line
P11 City Circuit Connection 25V Regulator Jumpers 1-2, 3-4
default. Power is fed to the zone/relay
IDNet Loop 1, Aux P9
TB1 card. No jumpers. Using 4007-9802,
Power, RUI Connection 25V Regulator Module
In this Chapter Power Supply Specifications ................ 4-2 IDNAC Section Overview .................... 4-3
Specifications ........................................ 4-3 Wiring.................................................... 4-3
Compatible Devices and Appliances .... 4-6 Auxiliary Relays Section Overview...... 4-8
Troubleshooting .................................... 4-9 SLC Channel Trouble LED Codes........ 4-9
System Trouble LED Codes................ 4-10
4-1
Chapter 4 IDNAC Power Supply
IDNAC Power Supply Specifications
Power Supply The IDNAC Power Supply can supply 4A of 24V power in addition to the base draw of the
Specifications CPU/Power Supply cards. The current draw taken from optional cards, IDNet Devices, Aux
Power, and NACs must be subtracted from 4A.
Table 4-2. 4007ES System Current Draw

2 A at 120 VAC, 50/60 Hz
Maximum AC Input
1 A at 240 VAC, 50/60 Hz
Current (see Note 1)

Standby Conditions (see Note 1)
(Battery Standby 24 V)
No alarms (NACs normal). IDNet devices connected 180 mA
Add to above for each additional IDNet or IDNAC device in

0.8 mA
standby
Total current for fully loaded IDNet or IDNAC channel in standby 431 mA
Current (see Note 1)

Alarm Conditions (see Note 1)
(Battery Alarm 24 V)
IDNAC ON: No IDNet LED On. No IDNet devices connected 185 mA
Add to above for each IDNet device in alarm (see note 2) 1 mA
Add to above for each IDNet LED On (20 maximum IDNet

2 mA
devices LEDs On)
Total current for fully loaded IDNet channel in alarm (20 LEDs
475 mA
On) (see note 2)
Notes:
1. Add an additional 9 mA per active auxiliary relay (Alarm or Standby)
2. IDNAC Alarm current depends on the IDNAC device used. Refer to the device’s manual for more informa-
tion on currents.
4-2
IDNAC Section
IDNAC Section The IDNAC power supply has a single SLC

Overview for connecting addressable IDNAC devices. IDNAC
The power supply is compatible with + - + -
TrueAlertES and TrueAlert Addressable
product lines (both multi and fixed candela).
The IDNAC output is Class B only. Class A
operation requires use of optional module
4007-9804, IDNAC dual Class A isolator.
The output is duplicated on the terminal block
to facilitate “T” tapping on the circuit at the
panel. EOL resistors are not required.
All wiring is supervised and power-limited.
Figure 4-2. IDNAC Terminal
Specifications Table 4-3. IDNAC Specifications
- Up to 12 4905-9929 remote TrueAlert Addressable Isolators per

IDNAC Circuit.
- Up to 30 devices connected directly to any isolator terminal pair*.
Supports - Up to six isolators between any appliance and the IDNAC SLC
terminals. All wiring is 20 AWG to 12 AWG.
*For more information on the isolator, refer to the 4905 Isolator+
Installation Instructions, 574-769.
Channel Voltage 29.5 VDC nominal.
Circuit Requirements The maximum alarm current is 3 A per circuits.
Isolator
To wire an IDNAC as a Class A circuit, the DCAI modules (4007-9804)
Isolator (DCAI) is required (2 Class A circuits with fault isolation). For more information
on Dual Class A isolator and on how to calculate Class B wiring with
isolation, refer to the DCAI Installation Instructions 579-1029.

Table 4-4 identifies the IDNAC wiring parameters that must be considered.
Table 4-4. IDNAC Wiring Parameters
IDNAC Wiring Limits
127 devices (IDNAC devices or other compatible devices). Refer

Channel Loading to the Compatible Devices and Appliances section for more
details.
Max. wiring distance
Max. cable load 10,000 ft (3,048m) per channel.
Max. wire length from

4,000ft (762m).
panel to any device
Note: If a shielded wire is used, cut it and tape it.
4-3
IDNAC Section, Continued
Wiring IDNAC Class B Wiring Tables

Use the following tables to calculate the wiring distance to farthest appliance.
Maximum wiring distance is the shorter of the distance limits as calculated by alarm current
voltage drop or by reaching the communications distance limit.
Table 4-5. Wiring Limit Based on Alarm Table 4-6. Wiring Limit Based on Communication
Current
Distance to the Last Appliance Line Distance to the Last Appliance
Alarm
20 18 16 14 12 Impedance Devices 20 18 16 14 12
Current
AWG AWG AWG AWG AWG (Ohms) AWG AWG AWG AWG AWG
0.050 4000 ft 4000 ft 4000 ft 4000 ft 4000 ft 14.54 1 1252 ft 2038 ft 3241 ft 4000 ft 4000 ft
0.200 1322 ft 2102 ft 3342 4000 ft 4000 ft 10.14 15 893 ft 1420 ft 2258 ft 3590 ft 4000 ft
0.250 1058 ft 1681 ft 2674 ft 4000 ft 4000 ft 9.12 20 804 ft 1278 ft 2033 ft 3231ft 4000 ft
0.450 588 ft 934 ft 1485 ft 2362 ft 3756 6.45 40 568 ft 904 ft 1437 ft 2285 ft 3634 ft
0.500 529 ft 841 ft 1337 ft 2125 ft 3380 6.00 45 528 ft 840 ft 1336 ft 2124 ft 3378 ft
Wiring distance must not exceed 4000 ft 3.40 95 299 ft 476 ft 757 ft 1203 ft 1913 ft
3.24 100 286 ft 454 ft 723 ft 1149 ft 1827 ft
Table 4-7. Ohms per 1000 ft 3.10 105 273 ft 435 ft 691 ft 1099 ft 1748 ft
Gage Ohms/1000 ft 2.97 110 262 ft 416 ft 662 ft 1052 ft 1673 ft

20 AWG 11.347 2.85 115 251 ft 399 ft 634 ft 1009 ft 1604 ft
18 AWG 7.137 2.73 120 241 ft 383 ft 609 ft 968 ft 1539 ft
16 AWG 4.488 2.58 127 228 ft 362 ft 576 ft 915 ft 1456 ft
14 AWG 2.8230 Wiring distance must not exceed 4000 ft
12 AWG 1.7750
4-4
Wiring IDNAC Class B Wiring

To connect the power supply to IDNAC IDNAC IDNAC
appliances using Class B wiring: Device Device Device
1. Route the wire from the “+” and
the “-” outputs on the IDNAC
terminal block (TB2) to the IDNAC IDNAC
IDNAC
appropriate inputs on a Device Device Device
peripheral notification
appliance.
2. Route wire from the first appli- T-TAP
ance to the next one. “T” tap- T-TAP
ping is allowed. Repeat for each T-TAP
appliance. + - + -
3. Repeat steps 1 and 2 for each
IDNAC output you want to use. IDNAC
Figure 4-3. Class B Wiring

Notes: 1. Notification appliances are rated per individual nameplate label. Maintain correct polarity on termi-
nal connections.
2. Each IDNAC + and - terminal is rated for 2 identical wires. This allows up to 4 Class B T-TAP cir-
cuits directly from each IDNAC terminal block. See Figure 4-3.
4-5
Compatible The devices and appliances listed in Table 4-8 are compatible with the IDNAC power supply.
Devices and Notification devices are synchronized within the 4007ES system, including any attached 4009
Appliances series NAC extenders.
Table 4-8. Compatible Devices and Appliances
Addressable Device Description Model Numbers
4009-9601 (platinum)
4009 IDNAC Repeater
4009-9602 (red)
Dual Class A Isolator (DCAI) 4007-9804
TrueAlert Addressable Isolator+ module 4905-9929
Addressable Device TrueAlert ES Appliance TrueAlert Appliance
Appliance Description Model Numbers Model Numbers
49AO-WRF 49AO-WWF
49MT-WRS-BA1
49AO-WRF-BA 49AO-WWF-BA
Audible Only Horn 49AO-WWS-BA 49MT-WWS-BA1
49AO-WRS-BA 4901-9850 4901-9853
notification appliances 49MT-WWF-BA1
49AO-WRS 49MT-WRF1
49AO-WRQ 49MT-WRF-BA1 49MT-APPLW1
49MTV-WRF-BA2
49AV-WRF 49AV-WWF-BA 49MTV-WRS-BA2
49AV-WWF 49AV-WWS-BA
Audible/Visible notification 49AV-WRS 49MTV-WWF2 4906-9227 4906-9229
49AV-WRF-BA
appliances 49AV-WRQ 49MTV-WWF-BA2 4906-9228 4906-9230
49AV-WRQ-BA
49AV-WRS-BA 49MTV-WRF2 49MTV-WWS-BA2
49MTV-APPLW2
49VO-WRF 49VO-WRS-BA 49VO-WRS
49VO-WWF 49VO-WWA-BA 49VO-WWS
49VO-WRA-A 49VO-WWF-BA 49VO-WWA
Visible Only notification 4906-9201 4906-9203
49VO-WWA-A 49VO-WWS-BA 49VO-WWQ
appliances 4906-9202 4906-9204
49VO-WRA-BA 49VO-WRA-A-BA 49VO-WRA
49VO-WRF-BA 49VO-WWA-A-BA 49VO-WRQ
49VO-WRQ-BA 49VO-WWS-A-BA 49VO-APPLWE
Speaker/Visible notification 4906-9251
4906-9254
appliances (visible/strobe) 4906-9253
Audible/Visible
49AV-WRFO 49AV-WWFO-BA 49AV-WRQO-C
Weatherproof notification N/A
49AV-WRFO-BA 49AV-APPLW-CO 49AV-WRFO-C
appliances
49VO-WRFO 49VO-WWFO-BA
Visible Only Weatherproof 49VO-WRQO-C
49VO-WRFO-BA 49VO-APPLW-CO N/A
notification appliances 49VO-WRSO
49VO-WRSO-BA 49VO-WRFO-C
TrueAlert Adapter N/A 4905-9816
59VO-WRF 59VO-WRFAB 59VO-WWFAB-BA
59VO-WRF-BA 59VO-WRFAB-BA 59VO-APPLWR
LED Visible Only Wall Mount
59VO-WWF 59VO-WWFAB 59VO-APPLWW
59VO-WWF-BA
LED Visible Only High 59VO-WRFH-BA 59VO-WRFABH-BA 59VO-APPLWRH
Candela Wall Mount 59VO-WWFH-BA 59VO-WWFABH-BA 59VO-APPLWWH
59VO-WRFO 59VO-WRFABO 59VO-APPLWR-O
LED Visible Only Wall Mount
59VO-WRFO-BA 59VO-WRFABO-BA 59VO-APPLWW-O
Weatherproof
59VO-WWFO-BA 59VO-WWWFABO-BA
LED Visible Only High
59VO-APPLWRH-O
Candela Wall Mount
59VO-APPLWWH-O
Weatherproof
59AV-WRF 59AV-WRFAB 59AV-WWFAB-BA
LED Audible/Visible Wall 59AV-WRF-BA 59AV-WRFAB-BA 59AV-APPLWR
Mount 59AV-WWF 59AV-WWFAB 59AV-APPLWW
59AV-WWF-BA
4-6
Table 4-8. Compatible Devices and Appliances

LED Audible/Visible Wall 59AV-WRFH 59AV-WRFABH 59AV-APPLWRH
Mount 59AV-WRFH-BA 59AV-WRFABH-BA 59AV-APPLWWH
High Candela 59AV-WWFH-BA 59AV-WWFABH-BA
59AV-WRFO 59AV-WRFABO 59AV-APPLWR-O
LED Audible/Visible Wall
59AV-WRFO-BA 59AV-WRFABO-BA 59AV-APPLWW-O
Mount Weatherproof
59AV-WWFO-BA 59AV-WWFABO-BA
LED Audible/Visible Wall
59AV-APPLWRH-O
Mount High Candela
59AV-APPLWWH-O
Weatherproof
59AO-WRS 59AO-WWS 59AO-APPLWR
Audible Only Wall Mount
59AO-WRS-BA 59AO-WWS-BA 59AO-APPLWW
Audible Only Wall Mount 59AO-WRSO 59AO-WWSO-BA
59AO-APPLWW-O
Weatherproof 59AO-WRSO-BA 59AO-APPLWR-O
Plate 59AP-EUROBB
Notes:
1. Maximum thirty-two (32) 49MT appliances per circuit.
2. Maximum twenty-one (21) 49MTV appliances per circuit.
4-7
Auxiliary Relays Section
Table 4-9. Auxiliary Relays Specifications

Auxiliary Relays Electrical Specifications:
Section Overview
Relay circuit rated to
2 A at 30 VAC or 30 VDC, resistive load.
switch:
Relay contacts are Form C dry contacts. Transorbs provide

Contacts: suppression to Earth. Do not switch voltages greater than rating, or
damage may result.
Power
When power through auxiliary contacts is provided by the power supply, wiring is power-
limited.
When power through auxiliary contacts is not provided by the power supply, use in-line fuse
holder 208-165 with 208-183, 1A fuse with attached cap (supplied separately). If the power
source is not power-limited to the requirements of UL864, wiring is to be segregated to the
non-power-limited spaces of the cabinet.
Note:
The Aux Relays terminals on Common
the IDNAC power supply are Normally
controlled by two on-board Normally 2
programmable relays. The closed
open 12 AWG (3.309 mm ) to
relay circuits are not 2
18 AWG (0.8231 mm )
supervised
N.O. C N.C N.O. C N.C
AUX RELAY1 AUX RELAY2
Figure 4-4. Aux Relay Terminals
4-8
Troubleshooting
Troubleshooting The code produced by the lit yellow indicator LEDs corresponds to a trouble that is either
occurring on the System or on the SLC Channels. See Table 4-10 for the 4007ES LED
definitions and Table 4-11 for the LEDs and their codes.
IDNAC Channel troubles are indicated by yellow LEDs labeled IDNAC TBL and letters A to
D. When the IDNAC TBL LED is lit, the IDNAC Channel is experiencing a trouble. Refer to
Table 4-1 for the trouble codes for LEDs A to D. The LED SCROLL pushbutton can be used to
scroll through multiple trouble indicators.
Table 4-10. 4007ES Indicator LEDs.
LED: A, B, C, D Signal various trouble conditions LEDs
on the 4007ES and its SLC.
Refer to Table 4-11 and
Table 4-12 for troubles details
IDNAC TBL When On steady, refer to Table
4-11 for detailed troubles Comm Loss
indicated by LEDs A-D IDNAC TBL
A
B
LED COMM Loss Indicates that the communica- C
tion between the IDNAC power D
supply and the CPU is lost
Scroll Push Used to scroll through multiple Scroll push
button (SW1)
Button (SW1) troubles, since only one trouble
can be displayed at a time.
Figure 4-5. LEDs on the 4007ES Power Supply
SLC Channel SLC Channel troubles are indicated by LEDs A to D, as well as IDNAC. Refer to Table 4-11
Trouble LED for the description of the LEDs.
Codes
Table 4-11. SLC Channel Trouble LED Codes
IDNAC A B C D Description:
IDNAC Channel Fail: The channel is not responding.
IDNAC Short Circuit: There is a short circuit on the channel.
IDNAC Duplicate Device: There are 2 devices on the channel

that have the same address.
IDNAC Missing device: There is a device programmed on the
channel that it cannot detect.
IDNAC Extra Device: The channel is detecting the address of
a device that has not been programmed.
IDNAC Wrong Device: The channel is detecting a device that
had been programed as the wrong “type”.
IDNAC Controller Fail: The channel can no longer detect the
controller.
IDNAC Address Out of Range: There is a device with an
unsupported address on the channel.
IDNAC Isolator Trouble: An isolator on the channel is open.
IDNAC Overcurrent: A device on the Channel is drawing too

much current.
IDNAC Earth Trouble: There is a positive or a negative earth
fault on the channel.
4-9
Troubleshooting, Continued
System Trouble System troubles are indicated by LEDs A to D.

LED Codes Table 4-12. System Trouble LED Codes
A B C D Description:
No Trouble: There are no troubles detected on the system.
AC Fail: The AC power is disconnected but the battery is working.
Low Battery: The battery voltage is under 22.8 V.
Battery Cutout: The Battery voltage is below 19.4 V. At this point, if jumper
P16 is set to “battery disconnect when depleted”, the system will shut down.
Depleted/Missing Battery: If jumper P16 is not set to “battery disconnect
when depleted”, this trouble will appear when the battery voltage is below
19.4 V. This code will also appear if the system cannot detect the battery.
Charger Trouble: There is a trouble with the battery charger.
Card Overcurrent: The module is drawing too much current.
Negative Earth: The circuit is shorted to ground on the negative wire.
Positive Earth: The circuit is shorted to ground on the positive wire.
Negative Earth on RUI: The RUI circuit is shorted to ground on the negative
wire.
Positive Earth on RUI: The RUI circuit is shorted to ground on the positive
wire.
City Circuit 1 Trouble: The trouble configured on the City Card’s circuit one
has been triggered.
City Circuit 2 Trouble: The trouble configured on the City Card’s circuit two
has been triggered.
AuxNAC Open: Depending on the chosen configuration, either the Aux circuit
or the NAC circuit is open.
AuxNAC Short: Depending on the chosen configuration, either the Aux circuit
or the NAC circuit is experiencing a short circuit.
AuxNAC Overcurrent: Depending on the chosen configuration, either the
Aux circuit or the NAC circuit is drawing too much current.
4-10
Chapter 5
4007ES Power Supplies
Introduction This chapter describes the common sections of both the 4007ES Hybrid NAC power supply
and the 4007ES IDNAC power supply.
In this chapter Power Supplies Specifications.......................... 5-1 Wiring Guidelines ....................... 5-1
IDNet Section Overview................................... 5-2 Specifications .............................. 5-2
Device Addressing (Class A and Class B)........ 5-2 Wiring ......................................... 5-3
AUX PWR/SNAC Overview............................ 5-5 RUI Overview ............................. 5-7
Troubleshooting ................................................ 5-8
Power Supplies Operating Conditions:

Specifications Operating Temperature Range 32oF - 120oF (0oC-49oC).
Operating Humidity Range Up to 93% relative humidity at 90oF (32oC), non-con-
densing.
Wiring Guidelines Class A wiring allows devices to communicate with the FACP even in the event of a single
open circuit somewhere on the loop. Class A wiring requires that two wires are routed from
the power supply to each device, and then back again to the power supply.
Class B wiring allows “T” tapping, and therefore requires less cable distance per installation
than Class A.
Auxiliary power only: Supervision must be provided if the auxiliary power circuit is to be
wired as a power-limited circuit. In order to connect a circuit using PL wiring, the devices
being powered must all be addressable, or a UL Listed EOL relay must be used to supervise
the circuit.
5-1
Chapter 5 4007ES Power Supplies
IDNet Section
IDNet Section The power supply provides an isolated IDNet

Overview channel. This section is compatible with IDNet IDNet
communicating initiating devices and allows the B+ B- A+ A-
system CPU to communicate with up to 250
peripheral devices, such as smoke detectors and
pull stations.
Figure 5-1. IDNet on the Power Supply
Specifications Table 5-1. IDNet Specifications

Up to 250 addressable IDNet devices and up to 43 coded piezo
sounders may be coded by the IDNet channel. Base panel
Supports:
supports 100 points, with 75 additional points per additional
IDNet+ Loop Expansion Module (refer to manual 579-1106).
Channel Voltage 30 VDC (normal); 35 VDC Alarm.
to Remote Devices Data rate is 3333 bps.
Output circuits are supervised and power-limited.
Earth Detection 10k ohms minimum from either positive or negative terminals.
Threshold:
Refer to Table 3-2 for the IDNet current on a NAC power supply.
Circuit Requirements:
Refer to Table 4-2 for the IDNet current on a IDNAC power supply.
LEDS:
For detailed information on LEDs troubleshooting, refer to Table 5-7 and Table 5-8 in the
Troubleshooting section.
Device The IDNet section can be wired as a Class A circuit or a Class B circuit.
Addressing Class A wiring provides an alternate communication path that allows communication to all
(Class A and devices to be maintained when a single open circuit fault occurs. Class A wiring requires two
Class B) wires to be routed from the IDNet Primary Terminals (B+, B-) to each device, and then back to
the IDNet Secondary Terminals (A+, A-). Wiring is in/out, “T” tapping is not allowed.
Class B wiring allows “T” tapping. IDNet wiring is inherently supervised due to individual
device level communications. EOL resistors are not required.
5-2
IDNet Section, Continued
Device • If no remote isolators or isolator bases are on the loops, device addressing can be assigned
Addressing without concern for sequence.
(Class A and • If remote isolators or isolator bases are on the loops, the required addressing approach
Class B) is to start from the “B” side and assign each successive isolator a higher address than the
isolator it precedes.
• For Class B wiring only, the “A” output and “B” output per loop are connected together
in parallel via a jumper.

Table 5-2 identifies the IDNet wiring parameters that must be considered when installing this
card. For additional wiring information, refer to document 900-408, Simplex Addressable Fire
Alarm Panels Field Wiring Specifications.
Table 5-2. IDNet Wiring Parameters
IDNet Wiring Capacitance Parameters
Parameter Value
Maximum Supported Channel Capacitance The sum of line-to-line capacitance, plus the capacitance of
either line-to-shield (if shield is present) = 0.6 µF
IDNet Wiring Class A and Class B Limits

Channel Loading Up to 125 devices 126 to 250 devices
Max. resistance to compatible devices.

(Include the 2081-9044 Overvoltage 50 ohms maximum 35 ohms maximum
Protector resistance when applicable)
Maximum wiring distance*:

4000 ft (1219 m) 2500 ft (762 m)
(18 AWG, 16 AWG, 14 AWG, 12 AWG)
*Notes:
Total cable load
• The "maximum wiring distance" is the maximum must not exceed
Device
Device
distance from both the IDNet control terminals (primary XXXX ft maximum to
12,500ft (3,8km)
and return) to the farthest device on the circuit. See farthest device from
Figure 5-2. either end of loop
Device
Device
Device
• Maximum wiring distance is determined by either Device
reaching the maximum resistance, the maximum
capacitance, or the stated maximum distance,
whichever occurs first.
• The total circuit cable load (amount of cable used) must
Control Terminals Control Terminals
not exceed 12,500ft (3,8km). (Class A wiring example) (Class B wiring example)
Figure 5-2. Maximum Wiring Distance

IDNet Wiring Considerations External wiring must be shielded (for lightning suppression) and 2081-9044
using 2081-9044 Overvoltage Overvoltage Protectors must be installed at building exit and entrance locations.
Protectors For more information, refer to the Model 2081-9044 Overvoltage Protector Installation
(2081-9044 is UL listed to Instructions, 579-832.
Standard 1459, Standard for Capacitance; each protector adds 0.006 µF across the connected line.
Telephone Equipment)
Resistance; each protector adds 3 ohms per line of series resistance; both IDNet wires
are protected; 6 ohms per protector will be added to total loop resistance.
Maximum distance of a single protected wiring run is 3270 ft (1 km).
Refer to document number 574-832, 2081-9044 Overvoltage Protector Installation
Instructions, for additional information.
5-3
IDNet Section, Continued
Wiring Class A Wiring

To wire IDNet section as a Class A circuit.
1. Make sure the jumpers on P2 are set to positions 3-5 and 4-6.
2. Route the wiring from the IDNet Circuit Primary Terminals (B+, B-) on TB1 of the IDNet to
the corresponding inputs on the first device.
3. Route wiring from the first device to the next as in/out. See Figure 5-3. Repeat for each
device.
4. Route the wiring from the last device to the terminals A+, A- to the panel, maintaining
polarity.
5. Shielded wire is not recommended. If shielded wires are present, cut and tape off the shield
at each end in the panel to prevent it from coming into contact with other components.
Metallic continuity of the shield must be maintained and insulated throughout the entire
length of the cable.
1
2
Devices
B B 1 2 1 2 1 2
Position Position +
3-5 A A 4-6
18 to 12 AWG
P2
IDNet
B+ B- A+ A-
P2
Figure 5-3. IDNet Class A Wiring

Class B Wiring
When wiring the circuit as Class B, both the B+, B- and A+, A- terminals are available for
parallel connections. Within the IDNet circuitry, A+ is connected to B+, and A- is connected to
B- so circuits can stem from either one. Additionally, two wires can be connected to each screw
terminal.
To wire IDNet as a Class B circuit:
1. Set the jumpers on P2 to positions 1-3 and 2-4.
2. Route wiring from the IDNet Circuit Primary Terminals (B+, B-) to the corresponding inputs
on the first device.
It is possible to add up to 4 circuits on the terminal block when using Class B wiring. See
Figure 5-4 for the diagram.
3. Route wiring from the first device to the next as in/out as shown in Figure 5-4. Repeat for
each device.
4. Shielded wire is not recommended. If shielded wires are present, cut and tape off the shield
at each end (in the panel and at the last device in each run) in the panel to prevent it from
coming into contact with other components. Metallic continuity of the shield must be
maintained and insulated throughout the entire length of the cable.
1
2
Position Position
1-3 B B 2-4
A A
P2
Devices
Different Circuit Configurations
1 2 1 3
IDNet CIRCUIT A 2 4
B+, B- B+ B- A+ A-
Terminals
TB1
B+ B- A+ A- B+ B- A+ A-
2 Circuit Configuration 4 Circuit Configuration
Note: For Class B wiring only, up to 4 parallel wiring “T”

taps may be made at the output terminal blocks
Figure 5-4. IDNet Class B Wiring
5-4
Auxiliary Power Section
AUX PWR/SNAC The AUX PWR/SNAC terminal block is located

Overview on the top left corner of the power supply. AUX PWR/SNAC
Through the ES Panel Programmer, this point + -
can be configured as either a 24V Auxiliary
(AUX) power or as a simple reverse polarity
Notification Appliance Circuit (NAC). This
circuit does not support TrueAlert addressable
devices nor non-addressable smartsync
appliances.
The AUX PWR/SNAC is rated 2 A maximum.
Current used is deducted from the total available
power supply current.
Figure 5-5. AUX/SNAC Terminal
Table 5-3. AUX/SNAC Wiring Specification
Output rating: 29.5 V maximum TYPICAL AUDIBLE/VISIBLE APPLIANCES
Current Rating: 2 A, maximum.
Earth Detection 10K ohms minimum from either 733-894 NAC -
Threshold positive or negative terminals. 10K EOLR
Wiring Gauge: 18 AWG (min.)

to 12 AWG (max.). NAC+
Wiring Notes:
B+
B-
1. All wiring from the AUX/SNAC is power limited.
2. Conductors must test free of all grounds and stray voltages B+ B- A+ A- + - B+ B- A+ A-
before connection to appliances and panel.
3. Terminate Class B NACs as shown using 733- 894 EOL.
For Canadian applications, mount end-of-line resistor to
IDNET AUX PWR / SNAC RUI
TEPG-US Model 431537 EOL plate in accordance with
ULC-S527.
Figure 5-6. Simple NAC Wiring

4. If wiring is routed outside the building, use of a listed secondary protector is required. Use Simplex 2081-9028 (rated 5 A) or 2081-
9044 (rated 0.2 A). A protector must be installed at each building exit/entrance. Each 2081-9028 adds 0.2 ohms wiring resistance.
2081-9044 adds 6 ohms wiring resistance, and will greatly reduce wiring distance.
Table 5-4. Simple NAC Wiring Limits
Alarm Current 20 AWG 18 AWG 16AWG 14 AWG 12 AWG Line Resistance (Ohms)
0.25 617 ft 981 ft 1560 ft 2480 ft 3944 ft 14.00
0.50 308 ft 490 ft 780 ft 1240 ft 1972 ft 7.00
0.75 206 ft 327 ft 520 ft 827 ft 1315 ft 4.67
1.00 154 ft 245 ft 390 ft 620 ft 986 ft 3.50
1.25 123 ft 196 ft 312 ft 496 ft 789 ft 2.80
1.50 103 ft 163 ft 260 ft 413 ft 657 ft 2.33
1.75 88 ft 140 ft 223 ft 354 ft 563 ft 2.00
2.00 77 ft 123 ft 195 ft 310 ft 493 ft 1.75
Note: This Chart indicates the maximum distance for 1/4 -2A loads. Wiring distance is from the panel terminals to the last
appliance. Use of a 2081-9044 protector reduces wiring distance.
5-5
Auxiliary Power Section, Continued
AUX PWR/SNAC Output of AUX or NAC is 24V nominal. Minimum voltage is 19.5 @ minimum battery;
Overview maximum is 29.5V. Aux Loads include the compatible 4007ES Annunciators series, 4090
series of IDNet ZAMs and IAMs and any listed device operating within the output limits of the
AUX. Calculate wiring loss for actual devices used. Compatible Appliances include 4904
series of free-run strobes, 4901 series non-smartsync horns, 4098 series TrueAlarm Sounder
Base and 4009 NAC extenders, used in reverse-polarity activation mode.
Table 5-5. Compatible Devices with 24V Aux. Power
2088-series relays 2098-series four-wire smoke detectors

4098-series four-wire smoke detectors 4190-9050/9051 4-20mA ZAMs
4090-series IDNet ZAMs
4100-7401, -7402 Graphic Annunciator
4602-6001, 4602-7001, 4602-7101, and Modules
4602-9150 RCU/SCU Modules
5-6
RUI Section
RUI Overview The 4007ES RUI channel supports the

following devices: RUI
• 4100-7401, 7402 Graphic Modules B+ B- A+ A-
• 4602-6001, -7001, 7101, 9150 RCU/SCU
Modules
Wire from the power supply's RUI channel on

terminal block TB1 to each RUI device. The
wiring may be Class A or Class B.
Figure 5-7 . Location of the RUI Terminal Block
Table 5-6. RUI Specifications

Supports: up to 10 RUI devices.
Channel Voltage 29.5 V nominal.
10K ohms minimum from either positive or
Earth Detection Threshold
negative terminals.
The maximum allowed line-to-line capacitance
(“+” to “-” terminals) is 0.58uF. For applications
Capacitance with shielded wire, be sure that the total
capacitance from line-to-line plus the shield to
either line is not more than 0.58uF.
Wiring
Maximum wiring distance:
2,500 feet (762 m) to device from PSU card.
(18 AWG, 16 AWG, 14 AWG, 12 AWG)
Maximum “T” tapping length 10,000 feet (3,048 m).
Notes:
Maintain correct polarity on terminal connections. Do not loop wires under terminals.
If Class A is not used, configure jumpers P1 accordingly.
Shield wire is not required. Twisted wire is recommended for improved noise immunity.
Figure 5-8 depicts Class A and Class B wiring.
1
2
1
2
B B Position Position
Position Position 1-3 B B 2-4
3-5 A A 4-6
A A
P1
P1
Class A Class B
DASHED LINES ARE FOR

CLASS A OPERATION
RUI RUI
4007ES PSU
A+ RUI Device RUI Device

A-
B+
B-
Figure 5-8. RUI Wiring to the Host Panel
5-7
Troubleshooting
Troubleshooting The code produced by the lit indicator LEDs corresponds to a trouble occurring on the system.
See Table 5-7 for the IDNet LED definitions and Table 5-8 the 4007ES trouble messages.
Table 5-7. 4007ES System Indicator LEDs
Normally off. Turns on steady if the IDNet is
Comm Trouble
not communicating with the FACP CPU.
Normally off. Illuminates to indicate a problem
with the IDNet channel:
IDNet trouble • Channel failure.
• Line short.
• Class A failure or an open line. Loop A Loop B Loop C IDNet Comm
Earth Fault -
Earth Fault+
Trouble Trouble
Earth fault+ Illuminates to indicate a positive earth fault.
Earth fault - Illuminates to indicate a negative earth fault. LEDs
Steady ON: Indicates an open or short condi-

IDNet LEDs: tion on indicated loop.
A, B, and C
Figure 5-9. LEDs on the 4007ES Power Supplies
Table 5-8. 4007ES System Trouble Messages
Message Definition
AC Fail AC power is not present or is too low for proper system operation.
Low Battery The battery voltage is below the 22.8 V nominal level by 10% or more.
Depleted/Missing The battery is either below 19.4 V or completely undetected.
Battery
Card Overcurrent The module is drawing more current than it should. Check for faults on the circuit.
Charger Trouble The battery charger is either defective or being heavily loaded by batteries. Read charger
current at front panel, if charger current is approximately 1.4 A, batteries are likely loading
the charger. Remove battery connection and measure the output. If the output is 27.6 (or
close, temperature dependent), there is a possibility of depleted batteries or a bad set of
batteries. Allow batteries to charge or replace them if they do not take a charge.
If the current is ~1.4 A with batteries and charger voltage below 20 V, remove the
batteries and recheck the charger voltage. If the voltage is around ~27.3 V, then the
batteries are heavily depleted.
Extra Device Appears if one or more extra devices (i.e., devices that have not been configured for the
IDNAC or IDNet channel) are on the system. Only one message appears, regardless of
the number of extra devices found.
Earth Fault Search Comes up during the Earth Fault Search diagnostic function. Once the search is initiated,
the front panel display indicates how far along the search process has progressed (10%,
25%…75%), and then shows the results of the search. The result either identifies the
offending circuit or indicates that the earth fault could not be found. During the search of
circuits (IDNet, NAC,IDNAC, and aux power), system alarm and trouble processing is
suspended.
Positive Earth Appears when a positive earth fault is detected.
Negative Earth Appears when a negative earth fault is detected.
Short Circuit Appears when a short is detected on the IDNAC/NAC channel. This status clears
automatically when the short circuit is removed.
Channel Fail Appears when each device on the IDNet channel has been configured, and when none of
the devices are communicating on the channel. This message does not appear if there
are no configured devices on the IDNAC channel.
5-8
Chapter 6
Optional Modules and Cards
Introduction The 4007ES can be ordered with a variety of optional cards and modules, depending on the
needs.
In this chapter 8-point Zone/Relay Card ...................... 6-1 25V Regulator Module.......................... 6-1
IDNet+ Loop Expansion Card .............. 6-1 LED Module ......................................... 6-1
SDACT Card......................................... 6-1 City Circuit............................................ 6-1
Alarm Relay Card ................................. 6-2 TrueInsight Service Gateway ................ 6-2
Dual Class A Isolator............................ 6-2 Example of Combinations..................... 6-2
8-point Zone/ The 8-point zone/relay card (4007-9801) mounts in the 4007ES panel. Up to four cards can be
Relay Card added. Each card allows the monitoring of up to eight Class B or four Class A zones, or eight
relay contacts.
For more information on the 8-point zone/relay card, refer to manual 579-1103.
25V Regulator The 25V regulator module (4007-9802) regulates the panel power supply output received
Module from the NAC power supply (4007ES) or the IDNAC power supply (4007ES hybrid) to a
25VDC level. The 25VDC regulated output is isolated from the panel and complies with
power-limited requirements.
For more information on the 25V regulator module, refer to manual 579-812.
IDNet+ Loop The IDNet+ loop expansion card (4007-9803) mounts directly on the IDNAC/NAC power
Expansion Card supply.Up to two cards can be added. Each card adds a single Class A/Class B IDNet+ loop
and increases the device capacity by 75 points.
For more information on the IDNet+ loop expansion card, refer to manual 579-1106.
LED Module The LED module (4007-9805) allows the operator to view the simultaneous signaling of an
alarm and trouble conditions on up to 24 zones. All the LEDs have configurable colors, red or
yellow, except the LEDs in the last column, which are configurable as red or green.
For more information on the LED module, refer to manual 579-1105.
SDACT Card The SDACT card (4007-9806) can be mounted in the 4007ES panel. It is used to notify a
central station when an event occurs, to report changes to a specific point, to be connected to a
transmitter for connection to a central station.
For more information, refer to manual 579-954.
City Circuit The city circuit card with disconnect switches (4007-8907) and without disconnect switches
(4007-9808) are used to annunciate alarms and other urgent indications to remote facilities.
Each city circuit module has two configurable circuits (alarm, trouble, or supervisory
reporting) and supports Reverse Polarity and Local Energy Master Box Applications. Only
one city card can be installed per system. It is not available when an alarm relay is used.
For more information on city circuits cards, refer to manual 579-955.
6-1
Chapter 6 Optional Modules and Cards
Optional Modules and Cards, Continued
Alarm Relay Card The Alarm relay card (4007-9809) is used to provide common unsupervised control functions
or indications for devices. Each relay module has three circuits (alarm, trouble, and supervisory
signals). It is not available when a city circuit card is used.
For more information on alarm relay card, refer to manual 579-955.
TrueInsight The remote service gateway (4190-6104) sends data to a remote service monitoring facility to
Service Gateway detail troubles in the panel. When the data reaches the monitoring facility, a qualified
technician is notified via e-mail and can then begin diagnostic process remotely.
For more information on the remote service gateway, refer to manual 579-953.
Dual Class A The Dual Class A Isolator (DCAI) (4007-9804) card converts the Class B output of the IDNAC
Isolator SLC into two isolated Class A outputs.
For more information on the DCAI, refer to manual 579-1029.
Example of Figure 6-1, Figure 6-2, and Figure 6-3 are examples of some of the combinations that can be
Combinations made in a 4007ES with the available optional cards and modules.
Zone/Relay
IDNet+ Loop
Module
Expansion cards
BLOCK E
Power Supply BLOCK G
BLOCK J BLOCK K
BLOCK C
BLOCK F
BLOCK H
Relay Module
BLOCK I BLOCK D
Zone/Relay
Module
DACT
Module
Figure 6-1. Example 1
6-2
Chapter 6 Optional Modules and Cards
Optional Modules and Cards, Continued
Example of
Combinations
IDNet+ Loop
Expansion cards
Power Supply
25V Regulator
Module
TrueInsight
Module
City Circuit
Module
Zone/Relay
Module
Zone/Relay
IDNet+ Loop
Module
Expansion cards
Dual Class A
Isolator Card Power Supply
Zone/Relay City Circuit

Module Module
6-3
Appendix A
ULC Programming Requirements
Common Earth This application monitors a system pseudo that counts the number of ground faults or troubles
Fault Ground and that occur on the system. Each time this counter increments (i.e. a ground fault or trouble
Common Trouble occurs), a yellow LED on the operator interface panel illuminates.
Indicator
Step 1. Add a Custom Control equation to monitor all ground faults:
1. Click on the Custom Control Tab
2. Add a new Equation
3. Paste the following equation:
[INPUTS]
STATUS ON
A112 | ANALOG | COUNTER | GROUND TROUBLE COUNTER
OR STATUS ON
2-0-8 | CARDSTAT | CSP | IDNET+ EARTH TROUBLE
[END INPUTS]
[OUTPUTS]
TRACK ON PRI=9,9
P535 | DIGITAL | UTILITY |
[END OUTPUTS]
Note: P535 is shown as an example; use any digital point.
A-1
ULC Programming Requirements
Common Earth Step 2. Open Color User Interface Card Properties Dialog
Fault Ground and
Common Trouble 1. Click on the Hardware Tab and expand the Unit 0, Box 1, Bay 1 icons to display the Color
Indicator User Interface Card. (Click on the + signs to the left of the Unit 0, Box 1, and Bay 1 icons to
expand them.)
Figure A-1. Selecting the Color User Interface Card

2. Right click on the Color User Interface card icon and select Properties.
3. Click on the Point Editing tab (see figure Figure A-2)
Figure A-2. The Display Tab: Display Checkbox

Step 3. Program the LED
1. Select one of the multicolor LEDs (3-2-1, 3-2-2, or 3-2-3) to program (Figure A-3).
2. Click on the Point Type drop down list box and select LEDYELLOW.
3. Click on the Mode drop down list box and select ON.
4. Enter P535 (or your chosen digital point number from the equation) (no spaces) in the
Reference Address field to program the LED for ground faults. OR
5. Enter A2 (no spaces) in the Reference Address field to program the LED to illuminate
whenever a general system trouble is present.
A-2
579-1102
Rev. E
© 2015-2016 Tyco Fire Protection Products. Specifications and other information were current as of publication and are subject to change without notice.

4007ES and 4007ES Hybrid Fire Alarm Systems: Installation Manual 579-1102 Rev. E

Uploaded by

Copyright:

Available Formats

4007ES and 4007ES Hybrid Fire Alarm Systems: Installation Manual 579-1102 Rev. E

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4007ES and 4007ES Hybrid Fire Alarm Systems: Installation Manual 579-1102 Rev. E

Uploaded by

Copyright:

Available Formats

4007ES and 4007ES Hybrid

Fire Alarm Systems

STATIC HAZARD - Static electricity can damage components. Handle as follows:

Copyrights, Trademarks, Cautions, Warnings, and Regulatory Info......................................i-2

Chapter. 3 NAC Power Supply ...................................................................................3-1

Chapter. 4 IDNAC Power Supply................................................................................4-1

Compatible Devices and Appliances .................................................................................................... 4-6

Chapter. 5 4007ES Power Supplies ...........................................................................5-1

Chapter. 6 Optional Modules and Cards ...................................................................6-1

Appendix. A ULC Programming Requirements ...................................................... A-1

Glossary Term Definition

Figure 1-1. 4007ES Panel Inside View

Mounting the • Due to the danger of metal fragments

the holes for the conduits, remove the

- To remove the electronics, unscrew

Top Trim Bands (x2)

Corner Pieces (x4)

Side Trim Bands (x2)

Figure 2-3 Semi-Flush Trim Kit

Figure 2-4. Applying the Trim

NPL Conduit Entry Side View of Panel

Keep NPL wiring this

Keep battery wiring terminals

coming in contact with other components. Metallic

insulated throughout the entire length of the cable. Note: 2098-9739

Wiring Guidelines • Wires must not be run through elevator shafts.

AC Supply Wiring Adhere to the following guidelines when wiring AC Power.

Final Installation To finalize the installation:

b. Insert the second battery

Figure 2-7. Power Supply

AUX/SNAC P1 NAC 1 NAC2 NAC3 NAC4

TB1 TB2 TB3

Option City/ BAT- BAT+

Table 3-1. Main Components Information

NAC Power Supply Specifications

IMPORTANT: Refer to the 4007-9801 8-Point Zone/Relay Card

No alarms (NACs normal). No IDNet devices connected. 145 mA

Add to above for each additional IDNet device in standby. 0.8 mA

Total current for fully loaded IDNet channel in standby. 345 mA

4 NACs ON: TBL Relay Activated: IDNet LED On. No

Add to above for each IDNet device in alarm. 1 mA

Add to above for each IDNet LED On (20 maximum IDNet

Total current for fully loaded IDNet channel in alarm. 480 mA

Figure 3-2. NAC Terminal on NAC Power Supply

Specifications Maximum Appliances 70 per circuit*

Wiring Wiring Parameters

Continued on next page

NAC Section, Continued

Wiring Wiring Distances

Table 3-6. Class B Wiring Distances

Max Distance Max Distance Max Distance Max Distance

Continued on next page

NAC Section, Continued

Wiring Class A Wiring

To connect the power BLK

using Class A wiring: APPLIANCE

1. Route wire from the RED BLK

“B+” and “B-” outputs of TYPICAL Leave the 378-030 EOL

Figure 3-3. Class A NAC Wiring