Ericsson Internal

METHOD OF PROCEDURE 1 (16)

Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

MOP for Manual LTE eNodeB Integration

Contents
1 Introduction .......................................................................................... 2
2 Revision ................................................................................................ 2
3 Preparation ........................................................................................... 2
3.1 Field tool requirements ............................................................. 2
4 Summary Time Plan ............................................................................. 3
4.1 Summary time plan .................................................................. 3
5 Network Impact .................................................................................... 3
6 Detailed Plan ........................................................................................ 3
6.1 Integration phase...................................................................... 3
6.1.1 Formatting DUS........................................................................ 3
6.1.2 Copy source to DUS ................................................................. 6
6.1.3 Setting the date and time on eNodeB ....................................... 9
6.1.4 Integrate enodeB ...................................................................... 9
 Ericsson Internal
METHOD OF PROCEDURE 2 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

1 Introduction

This document describes the implementation of the eNodeB Manual

Integration on Mobifone network in VietNam.

2 Revision

Revision Date Reason of Issue

PA1 01-Apr-16 First revision

3 Preparation

3.1 Field tool requirements

The field engineer should have a laptop with the following software

1. RBS Element Manager

2. LTE Package software

3. Filezilla FTP client

4. Java Run time Environment 6 or later

The field engineer should have the following cables to connect to the DUS
board.

1. USB to serial cable

2. Serial to RJ45 cable

3. CAT 6 LAN cable

 Ericsson Internal
METHOD OF PROCEDURE 3 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

4 Summary Time Plan

4.1 Summary time plan

Start Finish Duration Actual

No. Activity
Time Time Time Time

Integration phase 57 mins

1 Connect DUS 5 mins

2 Formatting the DUS 10 mins
3 Copy source L16A to DUS 20 mins
4 Setting the date and time on enodeB 2 mins
5 Integrate enodeB 20 mins

5 Network Impact
None

6 Detailed Plan

6.1 Integration phase

During the integration phase a field engineer will go to the site and do
commissioning which is explained in the steps below.

6.1.1 Formatting DUS

Since the DUS from the factory may contain different software, it is
recommended to format the DUS and load the required software L16A. The
steps for formatting are as shown below

Connect the serial cable to the LMT A port of DUS. Start the secureCRT
software and choose the correct USB interface.
 Ericsson Internal
METHOD OF PROCEDURE 4 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

If prompted for a user name and password in the terminal please enter
rbs/rbs. Once logged in the terminal should look as shown below.

On the SecureCRT, the eNodeB has to be brought to the backup mode. This
is done by using the reload -- command
 Ericsson Internal
METHOD OF PROCEDURE 5 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

Check the disk volume by using the vols command. If /c2 is missing we will
have to mount it by command as below

mount_c2

Now we format the /c2 and /d drives by the following commands

formathd /c2

formathd /d

Once format is completed, we reload the eNodeB by using reload command.

 Ericsson Internal
METHOD OF PROCEDURE 6 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

Back to the node to the backup mode by reload--

Now a default IP address is configured for the eNodeB. This is done by the
following command.

ifconfig le0 169.254.1.10 netmask 255.255.0.0

6.1.2 Copy source to DUS

Now that the DUS is formatted we can transfer the Package (/c2 and /d) to
the DUS. In order to do that the first step is to connect a LAN cable from the
laptop to port LMTB of DUS.

Set IP address of the laptop should be set as 169.254.1.11. The subnet mask
should be 255.255.0.0 and the gateway should be 169.254.1.10

Setting transfer type is binary

 Ericsson Internal
METHOD OF PROCEDURE 7 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

Open filezilla and connect to the DUS (169.254.1.10)

Make sure that / is the remote directory.

 Ericsson Internal
METHOD OF PROCEDURE 8 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

Now select both /c2 and /d in the laptop and upload them to the DUS.

Once completed, using a reload command so that DUS starts with a CV

 Ericsson Internal
METHOD OF PROCEDURE 9 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

6.1.3 Setting the date and time on eNodeB

We have to set the clock on the eNodeB so that the integration unlock
functionality can work well. The clock can be set by the command setclock as
shown below.

6.1.4 Integrate enodeB

Open RBS Element Manager, then click on Tools and Integrate RBS.

EMAS download: http://169.254.1.10/em/index.html

 Ericsson Internal
METHOD OF PROCEDURE 10 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

It will show basic windows

Click on browse and open Site Install files.

 Ericsson Internal
METHOD OF PROCEDURE 11 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

Click on Main Data, then fill the data

username: rbs
password: rbs

Checked on:
1. Do not use Security Activation
2. Do not use IP Security Activation

Then click Next

 Ericsson Internal
METHOD OF PROCEDURE 12 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

then Network configuration data window will popup.

 Ericsson Internal
METHOD OF PROCEDURE 13 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

1. Click next, we need to define all configuration files.

On Site basic configuration, click browse and choose site basic file
On Site basic configuration, click browse and choose site equipment file
Check on License Key and Upgrade package, as we do not use license
key file and upgrade package

.
 Ericsson Internal
METHOD OF PROCEDURE 14 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

2. Cabinet define

And click Start Integration button, to start integrating the eNodeB.

 Ericsson Internal
METHOD OF PROCEDURE 15 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01
 Ericsson Internal
METHOD OF PROCEDURE 16 (16)
Prepared (also subject responsible if other) No.

Minh Le C
Approved Checked Date Rev Reference

2016-04-01

For manual integration, we will not be seeing the above message as the
transport, radio and feature state scripts are not yet executed on the
node. The execution for manual integration stops at 80%.

Ping test to OSS : 10.19.202.8:

- if it is alive, call to person who take care run script define

transport and cell at OMC.

- If it is not answer, pls check transmission.