LED Indicate

Noted
GPS Tracker ‧ The upper cover (LED side) should face the sky and
• Yellow Light Stay On
Entry test mode and self-testing.
do not be covered with metal or metallic paint.
Operating Manual ‧ Need USB to RS-485 cable for programming settings.
• Green Light Stay On
Ready and test finish, entry to standby mode.
‧ Standard cable length 30cm or 200cm.
• After Standby Mode
[ Green Light Flashing Once Per Second ] SIM ready.
WG-E690 / WG-E69D [ Green Light Flashing Twice Per Second ] SIM ready + Server is connected.
WG-G690 / WG-G69D [ Green Light Flashing Three Times Per Second ]
SIM ready + Server is connected + GPS working.
• Red Light Flashing
LED
[ In Test Mode ] SIM or GPS error.
[ In Standby Mode ] NO SIM card inside.
• Red Light Stay On
Other errors.
• Green + Yellow Flashing
Installation Guide Entry configuration mode.
1. Install SIM card inside. • Yellow Light Flashing
2. Connect to car battery or power source. Entry boot mode, firmware update only.
3. Configure and setting everything you need. • LED Off
4. Make sure the indicate turn to green and flash three If you stay in silence mode, LED will turn off after test mode.
times.
5. After your server can collect tracker information,
please install tracker into your car.

Pin Define Fuse Holder Replace Fuse Push Down

Standard cable length 30cm or 200cm.

Push Down
• DC IN+_ Red Wire: DC 10~36V
WG-E690 • DC IN-_ Black Wire: GND
4 Close the top cover.
WG-G690 • RS-485 A_Green Wire: Non-isolator differential interface, Data - 1 Push the top cover.
• RS-485 B_White Wire: Non-isolator differential interface, Data +
• TRIGGER1_ Purple Wire: Signal level 10~33V, Triggered by status changed
• TRIGGER2_Blue Wire: Reserve
• IGNITION_Light Blue Wire: Signal level 10~33V, Ignition signal detect (Triggered by status changed)
• DI / O INPUT_Yellow Wire: Signal level 10~33V, Analog Input Support 0~10V / 0~20mA / 4~20mA /
ADC (0~10V), Digital Input support High / Low
• DI / O OUTPUT_Brown Wire: Open drain, ON / OFF function
Fuse
• DI / O GROUND_Gray Wire: Digital input / Digital output / TRIGGER / IGNITION GROUND

• DC IN+_ Red Wire: DC 40~60V

WG-E69D • DC IN-_ Black Wire: GND
RS-485 A_Green Wire: Non-isolator differential interface, Data -
WG-G69D • 5 Rotate it clockwise.
• RS-485 B_White Wire: Non-isolator differential interface, Data +
• SMBUS CLK_ Gray Wire: Signal level 3.3V, SMBUS CLOCK 2 Rotate it counterclockwise.
• SMBUS DAT_Yellow Wire: Signal level 3.3V, SMBUS DATA
• IGNITION_Purple Wire: signal level 40~58V, Ignition signal detect (Triggered by status changed)
Fuse Spec
• SMBUS GROUND_Brown: SMBUS reference ground
WG-E69X: 6.35Φ * 31.75mm 1A / 250V
• DI / O OUTPUT_Light Blue Wire: Open drain, ON / OFF function
3 Replace old fuse with a new one. WG-G69X: 6.35Φ * 31.75mm 0.5A / 250V
• DI / O GROUND_Blue Wire: Digital output / SMBUS / IGNITION GROUND
Install NANO SIM Card Specification

Wintec Co., Ltd.

1 Remove the four screws from the lower cover and WG-E690 WG-E69D
open the lower cover.
Cellular Protocol LTE-Cat1
Internet Protocol TCP / UDP / MQTT / MQTTS / Line Notify
Operating LTE Bands Band 1 / Band 3 / Band 5 / Band 7 / Band 8 / Band 28

www.win-tec.com.tw
LTE Transmit RF Power Maximum 23 dBm
Cellular Data Rate LTE-Cat1 (10 Mbps / DL, 5 Mbps / UL)
GNSS Receiver Type 16-Channel, C / A Code, GPS / GLONASS / BeiDou
GNSS Sensitivity Hot Start: -159 dBm / Cold Start: -148 dBm
GNSS Antenna Type Built in Patch Antenna
GNSS Protocol NMEA0183
GNSS Accuracy 2.5m CEP50
GNSS Acquisition Time (Average) Hot Star: 1 sec / Cold Start: 35 sec

[email protected]
Interface RS-485 / Digital Output / Digital or Analog Input RS-485 / Digital Output
Ignition Detect / Trigger Detect Ignition Detect / SMBUS
Indicator GPS / LTE Status Indicator
RS-485 Baud Rate 1200bps / 2400bps / 4800bps / 9600bps / 19200bps / 38400bps / 57600bps / 115200bps / 230400bps
Digital Output Support ON / OFF
2 Open SIM card holder, insert SIM card and lock holder.
Operating Temperature -20°C ~ 70°C
Main Unit Dimensions 70 x 53 x 20 mm
Waterproof IP 67
Input Power Supply DC 10 ~ 36 V (±5%) DC 40 ~ 60V (±3%)
Special Specification Flame Retardant

WG-G690 WG-G69D
SIM
Ca
rd
Cellular Protocol LTE-Cat M1 / NB-IoT
WG-G690 Internet Protocol TCP / UDP / MQTT / MQTTS / Line Notify
WG-G69D Operating LTE Bands Band 1 / Band 2 / Band 3 / Band 4 / Band 5 / Band 8 / Band 12 / Band 13 / Band 14 (M1 only) / Band 18 / Band 19
Band 20 / Band 25 / Band 26 / Band 27 (M1 only) / Band 28 / Band 66 / Band 71 (NB-IoT only) / Band 85
LTE Transmit RF Power Maximum 20 dBm
Cellular Data Rate LTE-Cat M1 (589 Kbps / DL, 1119 Kbps / UL) / NB-IoT (136 Kbps / DL, 150 Kbps / UL)
GNSS Receiver Type 16-Channel, C / A Code, GPS / GLONASS / BeiDou / Galileo
GNSS Sensitivity Hot Start: -159 dBm / Cold Start: -148.5 dBm
GNSS Antenna Type Built in Patch Antenna
GNSS Protocol NMEA0183
GNSS Accuracy 0.74m CEP50
GNSS Acquisition Time (Average) Hot Start: 1 sec / Cold Start: 30 sec
Interface RS-485 / Digital Output / Digital or Analog Input RS-485 / Digital Output
Ignition Detect / Trigger Detect Ignition Detect / SMBUS
Indicator GPS / LTE Status Indicator
WG-E690 RS-485 Baud Rate 1200bps / 2400bps / 4800bps / 9600bps / 19200bps / 38400bps / 57600bps / 115200bps / 230400bps
SIM Card

WG-E69D Digital Output Support ON / OFF

Operating Temperature -20°C ~ 70°C
Main Unit Dimensions 70 x 53 x 20 mm

PK FK03 VER.1
Waterproof IP 67
3 Put the lower cover back and reinstall the four Input Power Supply DC 10 ~ 36 V (±5%) DC 40 ~ 60V (±3%)
screws to the lower cover. Special Specification Flame Retardant