ECE DEPARTMENT NOTICE

INSTRUCTIONS FOR PROJECT REPORT SUBMISSION BY B. TECH (ECE 7 th sem ) STUDENTS

All final year ECE students are required to follow a prescribed sequential format for writing Minor
Project reports, the details of which are given below:

1. The sequence in which the project report material should be arranged and bound should be
as follows:
i. Cover page (sample copy attached as annexure-A).
ii. Title page. (sample copy attached as annexure-B)
iii. Contents with title & subtitle, page no. (Breakup of sections according to
explanation is advised).
iv. Certificate (sample copy attached as annexure-C)
v. Acknowledgment
vi. Declaration (sample copy attached as annexure-E)
vii. Abstract
viii. List of Figures
ix. List of Tables
x. Notations/nomenclature (if any)
xi. Executive summary (with Chapters & sections)
xii. References (only those references with proper citation which are used in the report)
should be in IEEE format
xiii. Appendix / Annexure/Data sheets( if any)

2. For text in the report a proper format must be followed i.e.

Chapter heading: 16 font-Times New Roman-Bold
Section heading : 14 font-Times New Roman-Bold
Rest of the text : 12 font-Times New Roman
Line spacing: 1.5

3. There should be Separator sheets between the chapters

mentioning chapter no. & the title & should also carry one
transparency with each separator sheet.

4. The report must consist of following chapters

• Chapter 1- Introduction
• Chapter 2- Project work (It can span in two or three subchapters depending on
type & volume of work. This contains the text & related to hardware &
software implementation)
• Chapter 3- Results and Discussion
• Chapter 4 Conclusions and future scope

5. Minimum No. of pages in report should be 80(excluding starting pages and annexure)

6. Numbering of pages up to List of tables should be in (ROMAN -8 font) and the text, beginning
with the Introduction, or of Chapter 1, should be numbered consecutively with
 Arabic numerals. Page numbers must be placed 1.5cm from the bottom center of each
page.

7. Numbering of Tables, Figures and Illustrations must be done sequentially, including the
Chapter number in which it is placed (for example, Figure 2.1, 3.2, etc).

8. Captions for Figures, Tables and Illustrations must be placed at the bottom of each, and
centered.

9. An annexure may be attached for graphs, Tables, images, simulation results etc after the
complied report. If the annexure pages are more, then another index page can be attached or
added to the main index page.

10. Cover should be hard bound with blue color & engraved text in Silver color. Two sets of
reports per group need to be submitted. Students can generate another copy for their own
referral.

11. Hard bound thickness cover should entitled with format:

MAY 2017 “PROJECT NAME” Enrolment No.

12. A CD inculcating soft copy of the report and project needs to be submitted.

13. Internal Project Score will be awarded as per the following criterion
i) Innovation and timely completion of project-10% ii)
Regularity as per attendance record-20%
iii) Quality/standard of project/Individual Sincere Effort-30%
iv) Internal Progressive & Viva(mid semester & end semester)-20% v)
Project Report-20%

14. The Report should be prepared in consultation of respective guides and the print should be
taken only after getting the green signal from guide.

Project Guide Name Mukesh Sahu

(Project Guide) HOD - ECE
(Annexure -A ) Cover Page

“MICROCONTROLLER BASED
ATTENDANCE SYSTEM”
(20 Arial)
MINOR PROJECT
(16 Normal Arial)

SUBMITTED IN PARTIAL FULFILLMENT OF THE

REQUIREMENTS FOR THE AWARD OF THE DEGREE OF
(14 Arial)

BACHELOR OF TECHNOLOGY
(18 Arial)
In
(14 Arial)
ELECTRONICS & COMMUNICATION ENGINEERING
(16 Arial)

Submitted By
NAME OF THE STUDENT
Enrollment. No. _____________
(16 Arial)

2017-18
GURU GOBIND SINGH INDRAPRASTHA UNIVERSITY, NEW DELHI.
(14 Times New Roman)-Bold)

GURU TEGH BAHADUR INSTITUTE OF TECHNOLOGY G-8

AREA, RAJOURI GARDEN, NEW DELHI-110064.
(1st letter 16, rest 14 Times New Roman)-Bold
(Annexure -B ) Title Page

“MICROCONTROLLER BASED
ATTENDANCE SYSTEM”
(20 Arial)

MINOR PROJECT
(16 Normal Arial)

SUBMITTED IN PARTIAL FULFILLMENT OF THE

REQUIREMENTS FOR THE AWARD OF THE DEGREE OF
(14 Arial)

BACHELOR OF TECHNOLOGY
(18 Arial)
in
(14 Arial)
ELECTRONICS & COMMUNICATION ENGINEERING
(16 Arial)

Submitted By
NAME OF THE STUDENT
Roll. No. _____________
(16 Arial)

2017-18
GURU GOBIND SINGH INDRAPRASTHA UNIVERSITY, NEW DELHI.
(14 Times New Roman)-Bold)
GURU TEGH BAHADUR INSTITUTE OF TECHNOLOGY G-8
AREA, RAJOURI GARDEN, NEW DELHI-110064.
(Annexure –C)

(This page should be printed on bond paper in landscape )

(Annexure -D )
CANDIDATE’S DECLARATION

I hereby declare that the work which is being presented in this Minor Project entitled, "TOPIC
NAME " submitted to GURU GOBIND SINGH INDRAPRASTHA UNIVERSITY, NEW
DELHI in the partial fulfillment of the requirements for the award of the degree of BACHELOR
OF TECHNOLOGY in ELECTRONICS & COMMUNICATION ENGINEERING, is an
authentic record of my own work carried out from August, 2017 to December, 2017 under the
supervision of PROJECT GUIDE NAME.

The matter embodied in this project report has not been submitted by me for the award of any other
degree.

Place:
Date: Uni. Enrollment No. ……………………..

This is to certify that the above statement made by the candidate is correct to the best of my
knowledge.

Guide Name
Project Guide
ABSTRACT

Information revolution implies that multimedia networks need high bandwidth real-time
…………………
ACKNOWLEDGEMENTS

Acknowledgement to Director, HOD, Project coordinator, guide n others

CONTENTS

Page No.
Candidate’s Declaration i
Abstract ii
Acknowledgement iii
Contents iv
List of Figures viii
List of Tables x
List of Publications xi
List of Abbreviations and Symbols Used xii

Chapter 1:
INTRODUCTION
1.1: 1
1.2: 3
1.3: 4
1.4: 5
1.5: 5

Chapter : 7
LITERATURE REVIEW

CHAPTER
CONCLUSION AND FUTURE SCOPE
7.1: CONCLUSIONS 79

7.2: FUTURE SCOPE 80

REFERENCES
LIST OF FIGURES

Figure Name of Figure Page No.

No:
1.1: Basic Structure of an Optical Amplifier 3

1.2: Block Diagram of The EDFA Optical Amplifier 4

3.1: Construction of Fiber 18

4.11: 42

4.12: 44

4.13: 47

5.1: 50

5.2: 51

6.9: 77
LIST OF TABLES

Table Name of Table Page No.

No:

6.1: 72

6.2: 75

6.3: 78
LIST OF PUBLICATIONS FROM THE PROJECT
LIST OF ABBREVIATIONS AND SYMBOLS USED