Scribd
Upload
218 views6 pages

Experiment 6 Performance of Centrifugal Compressor: A. Objective

This experiment aims to understand the working and performance characteristics of a centrifugal compressor. The objectives are to understand how a centrifugal compressor works and to plot performance curves and a compressor map by conducting experiments. The experiment will be conducted using an Armfield FM42 centrifugal compressor demonstration unit. Performance data will be collected at different flow rates by varying the outlet orifice opening and recording pressure, temperature and speed readings. The data will then be used to calculate performance parameters like compressor pressure ratio, input and output power, and efficiency.

Uploaded by

Surjit Dutta
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
218 views6 pages

Experiment 6 Performance of Centrifugal Compressor: A. Objective

This experiment aims to understand the working and performance characteristics of a centrifugal compressor. The objectives are to understand how a centrifugal compressor works and to plot performance curves and a compressor map by conducting experiments. The experiment will be conducted using an Armfield FM42 centrifugal compressor demonstration unit. Performance data will be collected at different flow rates by varying the outlet orifice opening and recording pressure, temperature and speed readings. The data will then be used to calculate performance parameters like compressor pressure ratio, input and output power, and efficiency.

Uploaded by

Surjit Dutta
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Experiment 6

Performance of centrifugal compressor


a. Objective

The objectives of this experiment are:


1. To understand the working of a centrifugal compressor.
2. To find the performance characteristics of the centrifugal compressor by conducting
experiments. Plot performance curves and compressor map.

b. Introduction

Centrifugal flow compressors, sometimes referred to as radial compressors, are a special


class of radial-flow work-absorbing turbo-machinery that include pumps, fans, blowers and
compressors. The earliest forms of these dynamic-turbo machines were pumps, fans and
blowers. What differentiates these early turbo machines from compressors is that the
working fluid can be considered incompressible, thus permitting accurate analysis through
Bernoulli's equation. In contrast, modern centrifugal compressors are higher in speed and
analysis must deal with compressible flow. In an idealized sense, the dynamic compressor
achieves a pressure rise by adding kinetic-energy/velocity to a continuous flow of fluid
through the rotor or impeller. This kinetic energy is then converted to an increase in static
pressure by slowing the flow through a diffuser.

Figure 10.1 Centrifugal pump

Advantages

Centrifugal compressors are used throughout industry because they have fewer rubbing
parts, are relatively energy efficient, and give higher airflow than a similarly sized
reciprocating compressor (i.e. positive-displacement). Their primary drawback is that they
cannot achieve the high compression ratio of reciprocating compressors without multiple
stages. Centrifugal fan/blowers are more suited to continuous-duty applications such as
ventilation fans, air movers, cooling units, and other uses that require high volume with
little or no pressure increase. In contrast, multi-stage reciprocating compressors often
achieve discharge pressures of 55 to 69 MPa. One example of an application of centrifugal
compressors is their use in re-injecting natural gas back into oil fields to increase oil
production.

Applications

Centrifugal compressors are often used in small gas turbine engines like APUs (auxiliary
power units) and smaller aircraft gas turbines. A significant reason for this is that with
current technology, the equivalent flow axial compressor will be less efficient due primarily
to a combination of rotor and variable stator tip-clearance losses. There are few single stage
centrifugal compressors capable of pressure-ratios over 10:1, due to stress considerations
which severely limit the compressor's safety, durability and life expectancy.

Additionally for aircraft gas-turbines; centrifugal flow compressors offer the advantages of
simplicity of manufacture and relatively low cost. This is due to requiring fewer stages to
achieve the same pressure rise. The fundamental reason for this stems from a centrifugal
compressor's large change in radius (relative to a multi-stage axial compressor); it is the
change in radius that allows the centrifugal compressor to generate large increases in fluid
energy over a short axial distance.

Centrifugal compressors are used in applications requiring pressurized air at high flow rates.
Some of the applications are cooling systems, burner air supply for furnace applications etc.

c. Equipment

Armfield FM42 Centrifugal Compressor Demonstration Unit


Armfield WD7 Interface Device
Compatible PC (not supplied) running Armfield FM42-304 software
Figure 10.2 Centrifugal compressor experimental set up

d. Pre-Lab

What is the difference between a reciprocating and rotary compressor?


What are the advantages of rotary compressors over reciprocating compressors?

e. Operating Instructions and Procedure

Check that the sensor and power leads from the FM42 are connected to the sockets on the
front of the IFD7.
Check that the IFD is connected to a suitable mains supply, and check the socket on the
front is connected using the lead provided to a suitable PC. Check that the red and green
indicator lights on the front of the IFD7 are illuminated.
Run the Arm field FM42-304 software on the PC, and check that the software indicates
‘WV: OK’ in the bottom right-hand corner of the window.
Switch on the mains supply to the WV?, and switch on the WD7 using the power switch on
the front. Check that the power switch on. Check that the green watchdog indicator on the
mimic screen is illuminated. Switch on the compressor using the ‘Power On’ button on the
software mimic diagram screen.
Check that the sensor readings on the software screen give sensible values. The pressure
readings should be zero when the compressor is not moving. The temperature should be
sensible given the ambient conditions in the room (typically between 15 and 30 ‘C). Zerothe
pressure sensors if necessary using the ‘Zero’ buttons on the mimic screen, Read through
the experiment before starting, to familiarize yourself with the procedure. Set the
compressor speed to maximum (100%) and note but do not record the flow rate. Fully close
the outlet aperture to give minimum flow. Click the button on the toolbar to record a set of
readings. Using the maximum air velocity as a guide, select incremental values for air
velocity that will give 10-15 individual steps between minimum and maximum velocity.

f. Working sheet

Sl.No Inlet Orifice Compressor Fan Speed Torque


temperature0C pressure differential N.m
Pa pressure, Pa
10 readings
for different
flow rates

g. Calculations

Compressor discharge

Q is the flow rate of air, m3/s


Cd is the coefficient of discharge of the orifice (0.596)
d is the orifice diameter (100mm), m
Po is the pressure drop across the orifice
ρ is the density of air, m3

Compressor total pressure

Ptf = + (p2-p1)

V1=Q/A1

V2=Q/A2

A1 and A2 are calculated based on the inlet and outlet radii of 50mm and 37.5mm
respectively.

Input power of the motor


2π
Ps =τ×ωmotor =τ× ×N motor
motor 60
Useful ( or output) Air power:
Pair=Q x ΔPtf
Overall efficiency (including transmission):
P air
η=
Ps
motor

Figure 10.3 Centrifugal Compressor Map.


h. Nomenclature

Hs= static head


Po = outet pressure
Pi= inlet pressure
ρ= density of air
g= acceleration due to gravity
Ai= inlet area
di= inlet diameter
Ao= outlet area
do= outlet diameter
Hv= dynamic head
Vo= velocity at outlet
Vi= velocity at inlet

i. Reference

1. Fluid Mechanics and Thermodynamics of Turbomachinery-by Dixon and


Hall 6th edition

You might also like