User Manual: WWW - Westlake.co - Uk UK Sales: 0800 298 8011

USER MANUAL
www.westlake.co.uk UK Sales : 0800 298 8011

Legal notice
Copyright © 2014 TELTONIKA Ltd. All rights reserved. Reproduction, transfer, distribution or storage of part
or all of the contents in this document in any form without the prior written permission of TELTONIKA Ltd is
prohibited. The manufacturer reserves the right to modify the product and manual for the purpose of technical
improvement without prior notice.
Other product and company names mentioned herein may be trademarks or trade names of their respective
owners.
Attention
Before using the device we strongly recommend reading this user manual first.
Do not rip open the device. Do not touch the device if the device block is broken.
All wireless devices for data transferring may be susceptible to interference, which could
affect performance.
The device is not water-resistant. Keep it dry.
Device is powered by low voltage +9V DC power adaptor.
2
Table of Contents
Legal notice.............................................................................................................................................................. 2
Attention.................................................................................................................................................................. 2
SAFETY INFORMATION ............................................................................................................................................ 7
Device connection ............................................................................................................................................... 8
1 Introduction ................................................................................................................................................... 9
1.1 Specifications ............................................................................................................................................. 9
1.1.1 LTE ...................................................................................................................................................... 9
1.1.2 UMTS.................................................................................................................................................. 9
1.1.3 GSM/GPRS/EDGE ............................................................................................................................... 9
1.1.4 Ethernet ............................................................................................................................................. 9
1.1.5 Wi-Fi ................................................................................................................................................... 9
1.1.6 Hardware ......................................................................................................................................... 10
1.1.7 Software ........................................................................................................................................... 10
1.1.8 Electrical, Mechanical & Environmental .......................................................................................... 10
1.1.9 Applications ..................................................................................................................................... 11
2 Setting up your router ................................................................................................................................. 12
2.1 Installation ............................................................................................................................................... 12
2.1.1 Front Panel and Back Panel ............................................................................................................. 12
2.1.2 Hardware installation ...................................................................................................................... 12
2.2 Logging in ................................................................................................................................................. 13
3 Operation Modes ......................................................................................................................................... 16
4 Powering Options ........................................................................................................................................ 16
4.1 Powering the device from higher voltage................................................................................................ 17
5 Status ........................................................................................................................................................... 18
5.1 System Information ................................................................................................................................. 18
5.2 Network Information ............................................................................................................................... 19
5.3 Device information .................................................................................................................................. 26
5.4 Services .................................................................................................................................................... 26
5.5 Routes ...................................................................................................................................................... 27
5.5.1 ARP ................................................................................................................................................... 27
5.5.2 Active IP-Routes ............................................................................................................................... 28
5.6 Realtime Graphs ...................................................................................................................................... 28
5.6.1 Traffic ............................................................................................................................................... 29
5.7 Events Log ................................................................................................................................................ 30
3
5.7.1 All ..................................................................................................................................................... 30
5.7.2 Authentication ................................................................................................................................. 30
5.7.3 Reboot.............................................................................................................................................. 31
5.7.4 Safemode ......................................................................................................................................... 31
6 Network ....................................................................................................................................................... 32
6.1 General..................................................................................................................................................... 32
6.1.1 Mobile configuration ....................................................................................................................... 32
6.1.2 Mobile Data On Demand ................................................................................................................. 33
6.2 SIM Management .................................................................................................................................... 33
6.3 Network Operators .................................................................................................................................. 34
6.4 Mobile Data Limit .................................................................................................................................... 35
6.4.1 Data Connection Limit Configuration .............................................................................................. 35
6.4.2 SMS Warning Configuration............................................................................................................. 35
6.5 WAN ......................................................................................................................................................... 36
6.5.1 Operation Mode .............................................................................................................................. 36
6.5.2 Common configuration .................................................................................................................... 36
6.6 LAN ........................................................................................................................................................... 41
6.6.1 Configuration ................................................................................................................................... 41
6.6.2 DHCP Server ..................................................................................................................................... 42
6.7 Wireless ................................................................................................................................................... 43
6.8 Backup WAN ............................................................................................................................................ 46
6.9 Firewall..................................................................................................................................................... 48
6.9.1 General Settings ............................................................................................................................... 48
6.9.2 DMZ.................................................................................................................................................. 49
6.9.3 Port Forwarding ............................................................................................................................... 49
6.9.4 Traffic Rules...................................................................................................................................... 51
6.9.5 Custom Rules ................................................................................................................................... 56
6.10 Static Routes ........................................................................................................................................ 57
7 Services ........................................................................................................................................................ 58
7.1 VRRP ......................................................................................................................................................... 58
7.1.1 LAN/WAN Settings ........................................................................................................................... 58
7.1.2 Advanced settings ............................................................................................................................ 58
7.2 Web filter ................................................................................................................................................. 59
7.2.1 Site blocking ..................................................................................................................................... 59
7.2.2 Proxy based URL content blocker .................................................................................................... 60
4
7.3 NTP ........................................................................................................................................................... 61
7.4 SNMP ....................................................................................................................................................... 62
7.4.1 SNMP Settings .................................................................................................................................. 62
7.4.2 TRAP Settings ................................................................................................................................... 63
7.5 VPN .......................................................................................................................................................... 64
7.5.1 OpenVPN .......................................................................................................................................... 64
7.5.2 IPSec ................................................................................................................................................. 66
7.5.3 GRE Tunnel ....................................................................................................................................... 69
7.5.4 L2TP .................................................................................................................................................. 70
7.5.5 Dynamic DNS.................................................................................................................................... 71
7.6 SMS Utilities ............................................................................................................................................. 73
7.6.1 SMS Utilities ..................................................................................................................................... 73
7.6.2 Send SMS and SMS Management .................................................................................................... 76
7.6.3 Remote Configuration...................................................................................................................... 76
7.7 Hotspot .................................................................................................................................................... 77
7.7.1 General settings ............................................................................................................................... 77
7.7.2 Logging ............................................................................................................................................. 78
7.7.3 Landing Page .................................................................................................................................... 80
7.8 Auto Reboot ............................................................................................................................................. 80
7.8.1 Ping Reboot ...................................................................................................................................... 80
7.8.2 Periodic Reboot................................................................................................................................ 82
8 System.......................................................................................................................................................... 82
8.1 Configuration Wizard ............................................................................................................................... 82
8.2 Configuration profiles .............................................................................................................................. 85
8.3 Administration ......................................................................................................................................... 85
8.3.1 General............................................................................................................................................. 85
8.3.2 Troubleshoot .................................................................................................................................... 86
8.3.3 Backup.............................................................................................................................................. 87
8.3.4 Access Control.................................................................................................................................. 87
8.3.5 Diagnostics ....................................................................................................................................... 88
8.3.6 MAC Clone ....................................................................................................................................... 89
8.4 User scripts .............................................................................................................................................. 89
8.5 Safe mode ................................................................................................................................................ 89
8.6 Firmware .................................................................................................................................................. 90
8.7 Restore point ........................................................................................................................................... 90
5
8.8 Reboot...................................................................................................................................................... 90
9 Functionality not listed in menu .................................................................................................................. 91
9.1 SMS by HTTP POST/GET ........................................................................................................................... 91
9.1.1 Syntax of HTTP POST/GET string ...................................................................................................... 91
9.1.2 Parameters of HTTP POST/GET string .............................................................................................. 91
9.1.3 Possible responses after command execution ................................................................................ 91
9.1.4 HTTP POST/GET string examples ..................................................................................................... 91
10 Glossary:....................................................................................................................................................... 93
6
SAFETY INFORMATION
In this document you will be introduced on how to use a RUT950 router safely. We suggest you to adhere to the
following recommendations in order to avoid personal injuries and or property damage.
You have to be familiar with the safety requirements before using the device!
To avoid burning and voltage caused traumas, of the personnel working with the device, please follow these
safety requirements.
The device is intended for supply from a Limited Power Source (LPS) that power consumption
should not exceed 15VA and current rating of overcurrent protective device should not exceed 2A.
The highest transient overvoltage in the output (secondary circuit) of used PSU shall not
exceed 36V peak.
The device can be used with the Personal Computer (first safety class) or Notebook (second
safety class). Associated equipment: PSU (power supply unit) (LPS) and personal computer (PC) shall
comply with the requirements of standard EN 60950-1.
Do not mount or service the device during a thunderstorm.
To avoid mechanical damages to the device it is recommended to transport it packed in a

damage-proof pack.
Protection in primary circuits of associated PC and PSU (LPS) against short circuits and earth
faults of associated PC shall be provided as part of the building installation.
To avoid mechanical damages to the device it is recommended to transport it packed in a damage-proof pack.
While using the device, it should be placed so, that its indicating LEDs would be visible as they inform in which working
mode the device is and if it has any working problems.
Protection against overcurrent, short circuiting and earth faults should be provided as a part of the building
installation.
Signal level of the device depends on the environment in which it is working. In case the device starts
working insufficiently, please refer to qualified personnel in order to repair this product. We recommend
forwarding it to a repair center or the manufacturer. There are no exchangeable parts inside the device.
7
Device connection
8
1 Introduction
Thank you for purchasing a RUT950 LTE router!
RUT950 is part of the RUT9xx series of compact mobile routers with high speed wireless and Ethernet
connections.
This router is ideal for people who‘d like to share their internet on the go, as it is not restricted by a cumbersome
cable connection. Unrestricted, but not forgotten: the router still supports internet distribution via a broadband cable,
simply plug it in to the wan port, set the router to a correct mode and you are ready to browse.
1.1 Specifications
1.1.1 LTE
 FDD 800/850/900/1800/1900/2100/2600 MHz
 Up to 100 Mbps downlink speed
 Up to 50 Mbps uplink speed
 All bands with diversity
1.1.2 UMTS
 850/900/1900/2100 MHz
 DC-HSPA+ mode: DL up to 43.2 Mbps, UL 5.76 Mbps
 HSPA+ mode: DL up to 21.6 Mbps, UL 5.76 Mbps
 UMTS mode: 384 kbps DL/384 kbps UL
 All bands with diversity
1.1.3 GSM/GPRS/EDGE
 850/900/1800/1900 MHz
 Power Class 4 (2 W, 33 dBm) GSM/GPRS 850/900 MHz
 Power Class 1 (1 W, 30 dBm) GSM/GPRS 1800/1900 MHz
 Power Class E2 (0.5 W, 27 dBm) for EDGE 850/900 MHz
 GPRS: 85.6 kbps DL/85.6 kbps UL (class 12)
 EDGE: 236.8 kbps DL/236.8 kbps UL (class 12)
1.1.4 Ethernet
 IEEE 802.3, IEEE 802.3u standards
 3 x LAN 10/100Mbps Ethernet ports
 1 x WAN 10/100Mbps Ethernet port
 Supports Auto MDI/MDIX
1.1.5 Wi-Fi
 IEEE 802.11b/g/n Wi-Fi standards
 2x2 MIMO
 AP and STA modes
 64/128-bit WEP, WPA, WPA2, WPA&WPA2 encryption methods
 2.401 – 2.495GHz Wi-Fi frequency range
 20dBm max Wi-Fi TX power
 SSID stealth mode and access control based on MAC address
9
1.1.6 Hardware
 High performance 560 MHz CPU with 128 Mbytes of DDR2 memory
 5.5/2.5mm DC power socket
 Reset/restore to default button
 2 x SMA for LTE , 2 x RP-SMA for Wi-Fi antenna connectors
 4 x Ethernet LEDs, 1 x Power LED
 1 x bi-color connection status LED, 5 x connection strength LEDs
1.1.7 Software
 OpenVPN, IPSec, GRE, L2TP, PPTP
 Backup WAN
 PPPoE
 Dynamic DNS
 SMS and Ping reboot, periodic reboot
 Status, configuration via SMS
 Send/read SMS via HTTP POST/GET
 Monitoring by SNMP, SNMP trap
 System log to record the status of the router
 VRRP
 Web filter
 Wireless hotspot with or without radius server
 SIM card switch controlled by signal, data limit, roaming
 Configuration profiles
 Dual image with safemode firmware
 Firmware update from bootloader via WebUI
 Restore point
1.1.8 Electrical, Mechanical & Environmental

 Dimensions (H x W x D) 80mm x 106mm x 46mm
 Weight 285g
 Power supply 100 – 240 VAC -> 9 VDC wall adapter
 Input voltage range 9 – 30VDC
 Power consumption < 7W
 Operating temperature -20° to 55° C
 Storage temperature -20° to 70° C
 Operating humidity 10% to 90% Non-condensing
 Storage humidity 5% to 95% Non-condensing
10
1.1.9 Applications
11
2 Setting up your router
2.1 Installation
After you unpack the box, follow the steps, documented below, in order to properly connect the device. For
better Wi-Fi performance, put the device in clearly visible spot, as obstacles such as walls and door hinder the signal.
1. First assemble your router by attaching the necessary antennas and inserting the SIM card.
2. To power up your router, please use the power adapter included in the box. (IMPORTANT: Using a different
power adapter can damage and void the warranty for this product.).
3. If you have a wired broadband connection you will also have to connect it to the WAN port of the router.
2.1.1 Front Panel and Back Panel
1,2,3 LAN Ethernet ports 1 LTE auxiliary antenna connector

4 WAN Ethernet port 2 LTE main antenna connector
5,6,7 LAN LEDs 3,5 Wi-Fi antenna connectors
8 WAN LED 4 Reset button
9 Power socket
10 Power LED
11 Connection status LED
12 Signal strength indication LEDs
2.1.2 Hardware installation
1. Remove back panel and insert SIM card which was given by your ISP (Internet Service Provider). Correct SIM card
orientation is shown in the picture.
SIM 1 (primary) SIM 2 (secondary)
2. Attach LTE main and Wi-Fi antennas.

3. Connect the power adapter to the socket on the front panel of the device. Then plug the other end of the power
adapter into a wall outlet or power strip.
4. Connect to the device wirelessly (SSID: Teltonika_Router) or use Ethernet cable and plug it into any LAN Ethernet
port.
12
2.2 Logging in
After you’re complete with the setting up as described in the section above, you are ready to start logging into
your router and start configuring it. This example shows how to connect on Windows 7. On windows Vista: click Start ->
Control Panel -> Network and Sharing Centre -> Manage network Connections -> (Go to step 4). On Windows XP: Click
Start -> Settings -> Network Connections -> (see step 4). You wont’s see “Internet protocol version 4(TCP/IPv4)”, instead
you’ll have to select “TCP/IP Settings” and click options -> (Go to step 6)
We first must set up our network card so that it could properly communicate with the router.
1. Press the start button 2. Type in “network connections”, wait for the results to pop
up.
3. Click “View network connections” 4. Then right click on your wireless device that you use to
connect to other access points (It is the one with the name
“Wireless Network Connection” and has signal bars on its
icon).
13
5. Select Internet Protocol Version 4 (TCP/IPv4) and then click 6. By default the router is going to have DHCP enabled, which
Properties means that if you select “Obtain an IP address automatically”
and “Obtain DNS server address automatically”, the router
should lease you an IP and you should be ready to login.
7. If you choose to configure manually here’s what you do:
First select an IP address. Due to the stock settings that your router has arrived in you can only enter an IP in the
form of 192.168.1.XXX , where XXX is a number in the range of 2-254 (192.168.1.2 , 192.168.1.254 , 192.168.1.155 and
so on… are valid; 192.168.1.0 , 192.168.1.1 , 192.168.1.255 , 192.168.1.699 and so on… are not). Next we enter the
subnet mask: this has to be “255.255.255.0”. Then we enter the default gateway: this has to be “192.168.1.1”. Finally
we enter primary and secondary DNS server IPs. One will suffice, though it is good to have a secondary one as well as it
will act as a backup if the first should fail. The DNS can be your routers IP (192.168.1.1), but it can also be some external
DNS server (like the one Google provides: 8.8.8.8).
14
Right click on the Wireless network icon and select Connect / Disconnect. A list should pop up with all available
wireless networks. Select “Teltonika” and click connect. Then we launch our favorite browser and enter the routers IP
into the address field:
Press enter. If there are no problems you should be greeted with a login screen such as this:
Enter the default password, which is “admin01” into the “Password” field and then either click Login with your
mouse or press the Enter key. You have now successfully logged into the RUT950!
From here on out you can configure almost any aspect of your router.
15
3 Operation Modes
The RUT9xx series router supports various operation modes. It can be connected to the internet (WAN) via
mobile, standard Ethernet cable or via a wireless network. If you connect to the internet via an Ethernet cable of Wi-Fi,
you may also backup your connection with mobile for added stability. On every case except when you connect to the
internet via Wi-Fi, you can distribute your internet via an Ethernet cable (3 ports) and/or a wireless network. When you
connect via Wi-Fi, you cannot have Wi-Fi in your LAN.
WAN LAN Mobile Backup link

Ethernet Wi-Fi
Mobile √ √ x
Ethernet √ √ √
Wi-Fi √ x √
In later sections it will be explained, bit by bit, how to configure your router to work in a desired mode.
4 Powering Options
The RUT9xx router can be powered from power socket or over Ethernet port. Depending on your network
architecture you can use LAN 1 port to power the device.
RUT9xx can be powered from power socket and over Ethernet simultaneously. Power socket has higher priority
meaning that the device will draw power from power socket as long as it is available.
When RUT9xx is switching from one power source to the other it loses power for a fraction of the second and
may reboot. The device will function correctly after the reboot.
16
Though the device can be powered over Ethernet port it is not compliant with IEEE 802.3af-2003 standard.
Powering RUT9xx from IEEE 802.3af-2003 power supply will damage the device as it is not rated for input voltages of
PoE standard.
4.1 Powering the device from higher voltage

If you decide not to use our standard 9 VDC wall adapters and want to power the device from higher voltage (15 –
30 VDC) please make sure that you choose power supply of high quality. Some power supplies can produce voltage
peaks significantly higher than the declared output voltage, especially during connecting and disconnecting them.
While the device is designed to accept input voltage of up to 30 VDC peaks from high voltage power supplies can
harm the device. If you want to use high voltage power supplies it is recommended to also use additional safety
equipment to suppress voltage peaks from power supply. One of the options is to use “Teltonika” PR1000 overvoltage
protection device conforming ISO 7637-2.
17
5 Status
The status section contains various information, like current IP addresses of various network interfaces; the state
of the routers memory; firmware version; DHCP leases; associated wireless stations; graphs indicating load, traffic, etc.;
and much more.
5.1 System Information

The System Information tab contains data that pertains to the routers operating system.
System explanation:
Field Name Sample value Explanation
1. Router Name Teltonika Name of the router (hostname of the routers system). Can be changed in
System -> Administration.
2. Host name Teltonika Indicates how router will be seen by other devices on the network. Can
be changed in System -> Administration.
3. Router Model Teltonika RUT9xx Routers model.
4. Firmware RUT9XX_T_00.00.372 Shows the version of the firmware that is currently loaded in the router.
Version Newer versions might become available as new features are added. Use
this field to decide whether you need a firmware upgrade or not.
5. Kernel Version 3.10.36 The version of the Linux kernel that is currently running on the router.
6. Local Time 2014-11-03, 14:33:14 Shows the current system time. Might differ from your computer,
because the router synchronizes it's time with an NTP server. Format
[year-month-day, hours:minutes:seconds].
7. Uptime 0h 40m 46s (since Indicates how long it has been since the router booted up. Reboots will
2014-11-03, 13:53:13) reset this timer to 0.Format [day’s hours minutes seconds (since year-
month-day, hours: minutes: seconds)].
8. Load Average 1 min: 11%; 5 mins: Indicates how busy the router is. Let's examine some sample output: "1
18%; 15 mins: 17% min: 11%, 5 mins: 18%, 15 mins: 17%". The first number mean past
minute and second number 11% means that in the past minute there
have been, on average, 11% processes running or waiting for a resource.
9. Temperature Device’s temperature
18
Memory explanation:
Field Name Sample Value Explanation
1. Free 94532 kB / 126452 kB The amount of memory that is completely free. Should this rapidly
(74%) decrease or get close to 0, it would indicate that the router is running
out of memory, which could cause crashes and unexpected reboots.
2. Cached 10828 kB / 126452 kB The size of the area of memory that is dedicated to storing frequently
(8%) accessed data.
3. Buffered 4308 kB / 126452 kB The size of the area in which data is temporarily stored before moving
(3%) it to another location.
5.2 Network Information

5.2.1.1 Mobile
Displays information about mobile modem connection.
Mobile information:
1. State Connected Mobile data connection status
2. IMEI 351579053495923 Modem's IMEI (International Mobile Equipment Identity) number
3. SIM card OK Indicates the SIM card's state, e.g. PIN required, Not inserted, etc.
state
6. Signal -91 dBm Received Signal Strength Indicator (RSSI). Signal's strength measured in dBm
strength
7. Operator LT BITE GSM Operator's name of the connected GSM network
state
8. Operator Registered (home) GSM network's status
9. Connection 3G (HSDPA) Indicates the GSM network's access technology
type
10. Bytes 80039 How many bytes were received via mobile data connection
received
11. Bytes sent 84651 How many bytes were sent via mobile data connection
19
5.2.1.2 WAN
Displays information about WAN connection.
WAN information:
1. Interface Wired Specifies through what medium the router is connecting to the internet.
This can either be Wired, Mobile or Wi-Fi.
2. Type DHCP Specifies the type of connection. This can either be static or DHCP.
3. IP address 192.168.99.199 The IP address that the routers uses to connect the internet.
4. Netmask* 255.255.255.0 Indicates the networks netmask
5. Gateway* 192.168.99.254 Indicates the default gateway, an address where traffic destined for the
internet is routed to.
6. DNS#* 8.8.8.8 Domain name server(s).
7. Connected* 0h 0m 22s How long the connection has been successfully maintained.
*-These fields show up on other connection modes.
**-Exclusive to other Modes with DHCP.
20
5.2.1.3 LAN
LAN information:
1. IP address 192.168.1.1 Address that the router uses on the LAN network.
2. Netmask 255.255.255.0 Indicates the networks netmask.
3. Connected 1h 6m 14s How long LAN has been successfully maintained.
DHCP Leases
If you have enabled a DHCP server this field will show how many devices have received an IP address and what
those IP addresses are.

1. Hostname Android-abc12 DHCP client's hostname
2. IP address 192.168.1.181 Each lease declaration includes a single IP address that has been leased to
the client
3. MAC address E8:92:A4:8D:75:27 The MAC (Media Access Control) address of the network interface on which
the lease will be used. MAC is specified as a series of hexadecimal octets
separated by colons
4. Lease time 11h 59m 59s Remaining lease time for addresses handed out to clients
remaining
21
5.2.1.4 Wireless
Wireless can work in two modes, Access Point (AP) or Station (STA). AP is when the wireless radio is used to
create an Access Point that other devices can connect to. STA is when the radio is used to connect to an Access Point via
WAN.
5.2.1.4.1 Station
Client mode information

1. SSID RUT9XX The SSID that the AP, to which the routers is connected to, uses.
2. Mode Station (STA) Connection mode – Client indicates that the router is a client to
some local AP.
3. Channel 2 (2.42 GHz) The channel that the AP, to which the routers is connected to, uses.
Your wireless radio is forced to work in this channel in order to
maintain the connection.
4. BSSID 00:1E:42:00:00:03 The MAC address of the access points radio.
5. Encryption WPA2 PSK (CCMP) The AP, to which the router is connected to, dictates the type of
encryption.
6. Bit rate 39.0 MBit/s The physical maximum possible throughput that the routers radio
can handle. Keep in mind that this value is cumulative - The bitrate
will be shared between the router and other possible devices that
connect to the local AP.
7. Country LT Country code.
22
5.2.1.4.2 Access Point
Wireless AP information
1. SSID Teltonika_Router_Test The SSID that is being broadcast. Other devices will see this and will
be able to use to connect to your wireless network.
2. Mode Access Point (AP) Connection mode – Master indicates that you router is an access
point.
3. Channel 11 (2.46 GHz) The channel which is used to broadcast the SSID and to establish new
connections to devices.
4. BSSID 00:1E:42:00:00:02 MAC address of your wireless radio.
5. Encryption No Encryption The type of encryption that the router will use to authenticate,
establish and maintain a connection.
6. Bit rate 1.0 MBit/s The bitrate will be shared between all devices that connect to the
routers wireless network.
7. Signal Quality 91% The quality between routers radio and some other device that is
connecting to the router. Will show 0% if no devices are trying to
connect or are currently maintaining a connection.
8. Country 00(World) Country code.
Additional note: MBit/s indicates the bits not bytes. To get the throughput in bytes divide the bit value by 8, for
e.g. 54MBits/s would be 6.75MB/s (Mega Bytes per second).
23
5.2.1.5 Associated Stations
Outputs a list of all devices and their MAC addresses that are maintain a connection with your router right now.
This can either be the information of the Access Point that the router is connecting to in STA mode or a list of all
devices that are connecting to the router in AP mode:

1. MAC Address 00:21:C5:15:05:34 Associated station's MAC (Media Access Control) address
2. Network Access point (AP) Associated station's mode and SSID (Service Set Identifier)
“Teltonika_Router_Test”
3. Signal -46dBm Received Signal Strength Indicator (RSSI). Signal's strength measured
in dBm
4. RX Rate 1.0Mbit/s, MCS 0, 20MHz The rate at which packets are received from associated station
5. TX Rate 1.0Mbit/s, MCS 0, 20MHz The rate at which packets are sent to associated station
5.2.1.6 OpenVPN Client (must be updated)

1. Status Enabled OpenVPN status
2. Type Client A type of OpenVPN instance that has been created
3. IP N/A Remote virtual network's IP address
4. Mask N/A Remote virtual network's subnet mask
5. Server IP N/A Remote virtual server's IP address
6. Time 4h 23m 15s For how long the connection has been established
24
5.2.1.7 OpenVPN Server

1. Status Enabled OpenVPN status
2. Type Client A type of OpenVPN instance that has been created
3. IP N/A Remote virtual network's IP address
4. Mask N/A Remote virtual network's subnet mask
5. Time 4h 23m 15s For how long the connection has been established
5.2.1.8 Client information

1. Common Name
2. Real Address
3. Virtual Address Virtual address which has been given to a client
4. Connection Since Since when connection has been established
25
5.3 Device information
The page displays factory information that was written into the device during manufacturing process

1. Serial number 12345678 Serial number of the device
2. Product code RUT950101000 Product code of the device
3. Batch number 0001 Batch number used during device’s manufacturing process
4. Hardware revision 0002 Hardware revision of the device
5. IMEI 860461024164561 Identification number of the internal modem
6. Ethernet LAN MAC 00:1E:42:10:80:01 MAC address of the Ethernet LAN ports
7. Ethernet WAN MAC 00:1E:42:10:80:02 MAC address of the Ethernet WAN port
8. Wireless MAC 00:1E:42:10:80:03 MAC address of the Wi-Fi interface
5.4 Services
The page displays usage of the available services
26
5.5 Routes
The page displays ARP table active IP routes of the device
5.5.1 ARP
Shows the routers active ARP table. An ARP table contains recently cached MAC addresses of every immediate
device that was communicating with the router.

1. IP Address 192.168.99.110 Recently cashed IP addresses of every immediate device that was
communicating with the router
2. MAC Address 00:1E:42:12:DC:54 Recently cashed MAC addresses of every immediate device that was
3. IP Address 192.168.99.110 Recently cashed IP addresses of every immediate device that was
27
5.5.2 Active IP-Routes
Shows the routers routing table. The routing table indicates where a TCP/IP packet, with a specific IP address,
should be directed to.

1. Network lan Interface to be used to transmit TCP/IP packets through
2. Target 192.168.1.0/24 Indicates where a TCP/IP packet, with a specific IP address, should be
directed
3. IP Gateway 0.0.0.0 Indicates through which gateway a TCP/IP packet should be directed
4. Metric 0 A number of network nodes through which a packet must go to reach
its destination
5.6 Realtime Graphs

Real-time graphs show how various statistical data changes over time.
28
5.6.1 Traffic
Field Name Explanation

1. Load This tri-graph illustrates average system load over the course of ~3 minutes; each new
measurement is taken every 3 seconds. The graph consists out of three color coded graphs,
each one corresponding to the average system load over 1 (red), 5 (orange) and 15 (yellow)
most recent minutes. Although not graphed, the page also displays peak loads over 1, 5 and 15
minutes.
2. Bridge Cumulative graph, which encompasses wired Ethernet LAN and the wireless network.
3. LAN+WAN Graphs the total traffic that passes through both WAN and LAN network interfaces.
4. WAN Graphs the amount of traffic which passed through the current active WAN connection.
5. Wi-Fi Shows the amount of traffic that has been sent and received through the wireless radio.
6. Wireless Graphs illustrate how signal strength, amount of noise and physical rate of wireless changes
over time.
7. Connections This graph shows a concise history of the amount of connections that the router maintained.
Blue graph indicates UDP connections, green TCP and red other types (ICMP, etc…). Other
values indicate each respective graphs average and peak connection amounts over 3 minutes.
29
5.7 Events Log
Event log displays such actions as: login, reboot, firmware flashing and reset.
5.7.1 All
5.7.2 Authentication
30
5.7.3 Reboot
5.7.4 Safemode
31
6 Network
6.1 General
6.1.1 Mobile configuration
Here you can configure the mobile specific settings which are used when connecting to your local 3G/LTE
network.

1. APN “APN” Access Point Name (APN) is a configurable network identifier used by a
mobile device when connecting to a GSM carrier.
2. PIN number “1234” or any number A personal identification number is a secret numeric password shared
that falls between 0000 between a user and a system that can be used to authenticate the user
and 9999 to the system.
3. Dialing
number
4. Authentication CHAP, PAP or none Authentication method, which your carrier uses to authenticate new
method connections. (This selection is unavailable on the alternate model)
5. Username “username” Your username and password that you would use to connect to your
carriers network. These field become available when you select an
authentication method (i.e. authentication method is not “none”).
These fields are always enabled on the alternate model.
6. Password “password” Shows the current system time. Might differ from your computer,
because the router synchronizes it's time with an NTP server. Format
[year-month-day, hours: minutes: seconds].
7. Service mode 2G only, 2G preferred, Your network preference. If your local mobile network supports 2G, 3G
3G only, 3G preferred, and 4G (LTE) you can specify to which network you wish to connect.
4G (LTE) only, 4G (LTE) E.g.: if you choose 2G, the router will connect to a 2G network, so long
preferred or automatic. as it is available, otherwise it will connect to a network that provides
better connectivity. If you select auto, then the router will connect to
the network that provides better connectivity.
32
Warning: If an invalid PIN number was entered (i.e. the entered PIN does not match the one that was used to
protect the SIM card), your SIM card will get blocked. To avoid such mishaps it is highly advised to use an unprotected
SIM. If you happen to insert a protected SIM and the PIN number is incorrect, your card won’t get blocked immediately,
although after a couple of reboots OR configuration saves it will.
6.1.2 Mobile Data On Demand
Field name Possible values Explanation

1. Enable Enable/Disable Mobile Data On Demand function enables you to keep mobile data
connection on only when it's in use
2. No data 1-99999999 A mobile data connection will be terminated if no data is transferred
timeout(sec) during the timeout period
6.2 SIM Management
33
Field name Possible values Explanation
1. Primary SIM card SIM 1 / SIM 2 SIM card that will be used in the system as a primary SIM card
2. Enable automatic Enable/Disable Automatically switch between primary and secondary SIM cards based
switching on the various rules and criterions defined below
3. On weak signal Enable/Disable Perform a SIM card switch when a signal's strength drops below a
certain threshold
4. Signal strenght -80 Lowest signal's strength value in dBm below which a SIM card switch
(dBm) should occur
5. On data limit Enable/Disable Perform a SIM card switch when mobile data limit for your current SIM
card is exceeded
Period Month/Week/Day Period for which data limit based SIM card switching should apply
6. Start day/Start A starting time for data limit based SIM card switching period
hour
7. Data limit (MB) 200 A data limit value in MB above which a SIM card switch should occur
8. On roaming Enable/Disable Perform a SIM card switch when roaming is detected
9. On data connection Enable/Disable Perform a SIM card switch when data connection fails
fail
10. Use same rules for Enable/Disable Apply the same SIM cards switching rules and criterions for both SIM
secondary SIM cards
11. Switch back to Enable/Disable Switch back to primary SIM card after timeout has been reached
primary SIM card
after timeout
12. Initial timeout 10 An initial timeout value in minutes after which a SIM card's switch-back
(min) should occur
13. Subsequent 20 A subsequent timeout value in minutes after which a SIM card's switch-
timeout (min) back should occur. This value is increased every time an unsuccessful
switch-back is made: new_timeout = old_timeout +
subsequent_timeout
14. Subsequent 20 A subsequent timeout value in minutes after which a SIM card's switch-
timeout (min) back should occur. This value is increased every time an unsuccessful
switch-back is made: new_timeout = old_timeout +
subsequent_timeout
6.3 Network Operators

This function lets you Scan, Select and enter manual Network Operator to which router should connect. Function
will provide great utility when router is in Roaming conditions.
34
1. SIM card in use SIM 1 / SIM 2 Shows current SIM card’s in use
2. Current operator „TELE2“ Operator's name of the connected GSM network
Note: after clicking Scan button - You will lose current mobile connection! For changing network operator status have to
be available. There is manual connection to network operator, you have to fill numeric name, and it’s have to be
available.
6.4 Mobile Data Limit

This function lets you limit maximum amount of data transferred on WAN interface in order to minimize
unwanted traffic costs.
6.4.1 Data Connection Limit Configuration

1. Enable data Enable/Disable Disables mobile data when a limit for current period is reached
connection limit
2. Data limit (MB) 200 Disable mobile data after limit value in MB is reached
3. Period Month/Week/Day Period for which mobile data limiting should apply
4. Start day/ Start A starting time for mobile data limiting period
hour
6.4.2 SMS Warning Configuration
35
1. Enable SMS Enable/Disable Enables sending of warning SMS message when mobile data limit for
warning current period is reached
2. Data limit (MB) 200 Send warning SMS message after limit value in MB is reached
Period Month/Week/Day Period for which mobile data limiting should apply
4. Start day/ Start A starting time for mobile data limiting period
hour
3. Phone number +37012345678 A phone number to send warning SMS message to, e.g. +37012345678
6.5 WAN
6.5.1 Operation Mode
Type Explanation
1. Wired An Ethernet cable connected to the WAN port of the router.
2. Wi-Fi The router will be able to connect to a local wireless access point and reach the internet through it.
3. Mobile The router will connect to your local mobile network for Mobile access.
6.5.2 Common configuration
Common configuration allows you to configure your TCP/IP settings for the wan network.
You can switch between the Static, DHCP or PPPoE protocol by selecting the protocol that you want to use and
then pressing Switch Protocol
Note: Mobile connection does not use either DHCP or Static protocol therefore it displays “none” in the
dropdown menu.
36
6.5.2.1 General Setup
6.5.2.1.1 Static:
This is the configuration setup for when you select the static protocol.
Filed name Sample Explanation

1. IPv4 address 192.168.99.162 Your routers address on the WAN network
2. IPv4 netmask 255.255.255.0 A mask used to define how “large” the WAN network is
3. IPv4 gateway 192.168.99.254 Address where the router will send all the outgoing traffic
4. IPv4 broadcast 192.168.99.255 Broadcast address (autogenerated if not set). It is best to leave this
blank unless you know what you are doing.
5. custom DNS servers 8.8.8.8 8.8.6.6 Usually the gateway has some predefined DNS servers. As such the
router, when it needs to resolve a hostname (“www.google.com”,
“www.cnn.com”, etc…) to an IP address, it will forward all the DNS
requests to the gateway. By entering custom DNS servers the router
will take care of host name resolution. You can enter multiple DNS
servers to provide redundancy in case the one of the server fails.
6.5.2.1.2 DHCP:
37
When you select the DHCP protocol you can use it as is, because most networks will not require any additional
advanced configuration.
6.5.2.1.3 PPPoE
This protocol is mainly used by DSL providers:
This is the configuration setup for when you select PPPoE protocol.
Filed name Sample Explanation

1. PAP/CHAP username test Your username and password that you would use to connect to your
carriers network.
2. PAP/CHAP password your_password A mask used to define how “large” the WAN network is
3. Access Concentrator isp Specifies the name of access concentrator. Leave empty to auto detect.
4. Service Name isp Specifies the name of the service. Leave empty to auto detect.
6.5.2.2 Advanced
These are the advanced settings for each of the protocols, if you are unsure of how to alter these attributes it is
highly recommended to leave them to a trained professional:
6.5.2.2.1 Static
38
Field name Sample value Explanation
1. Disable NAT On/Off Toggle NAT on and off.
2 Override MAC address 86:48:71:B7:E9:E4 Override MAC address of the WAN interface. If your ISP gives you
a static IP address it might also bind it to your computers MAC
address (i.e. that IP will only work with your computer). In this
field you can enter your computers MAC address and fool the
gateway in thinking that it is communicating with your computer.
3. Override MTU 1500 Maximum transmission unit – specifies the largest possible size of
a data packet.
4. Use gateway metric 0 The WAN configuration by default generates a routing table entry.
With this field you can alter the metric of that entry.
6.5.2.2.2 DHCP

1. Disable NAT Enable/Disable If checked, router will not perform NAT (masquerade) on this
interface
2 Use broadcast flag Enable/Disable Required for certain ISPs, e.g. Charter with DOCSIS 3
3. Use default gateway Enable/Disable If unchecked, no default route is configured
4. Use DNS server Enable/Disable If unchecked, the advertised DNS server addresses are ignored
advertised by peer
5. User gateway metric 0 The WAN configuration by default generates a routing table entry
With this field you can alter the metric of that entry
6. Client ID to send when
requesting DHCP
7. Vendor Class to send
when requesting DHCP
8. Override MAC address 86:48:71:B7:E9:E4 Override MAC address of the WAN interface. If your ISP gives you
a static IP address it might also bind it to your computers MAC
address (i.e. that IP will only work with your computer). In this
field you can enter your computers MAC address and fool the
gateway in thinking that it is communicating with your computer.
9. Override MTU 1500 Maximum transmission unit – specifies the largest possible size of
a data packet.
39
6.5.2.2.3 PPPoE

1. Disable NAT Enable/Disable If checked, router will not perform NAT (masquerade) on this
interface
2 Use default gateway Enable/Disable If unchecked, no default route is configured
3. Use gateway metric 0
4. Use DNS servers Enable/Disable If unchecked, the advertised DNS server addresses are ignored
advertised by peer
5. LCP echo failure 0 Presume peer to be dead after given amount of LCP echo failures,
threshold use 0 to ignore failures
6. LCP echo interval 5 Send LCP echo requests at the given interval in seconds, only
effective in conjunction with failure threshold
7. Inactivity timeout 0 Close inactive connection after the given amount of seconds, use 0
to persist connection
6.5.2.2.4 IP Aliases
IP aliases are a way of defining or reaching a subnet that works in the same space as the regular network.
40
As you can see, the configuration is very similar to the static protocol; only in the example a 99th subnet is
defined. Now if some device has an IP in the 99 subnet (192.168.99.xxx) and the subnets gateway metric is “higher” and
the device is trying to reach the internet it will reroute it’s traffic not to the gateway that is defined in common
configurations but through the one that is specified in IP aliases.
You may also optionally define a broadcast address and a custom DNS server.
6.6 LAN
This page is used to configure the LAN network, where all your devices and computers that you connect to the
router will reside.
6.6.1 Configuration

1. IP address 192.168.1.1 Address that the router uses on the LAN network
2 IP netmask 255.255.255.0 A mask used to define how large the LAN network is
3. IP broadcast 0 IP broadcasts are used by BOOTP and DHCP clients to find and
send requests to their respective servers
41
6.6.1.2 Advanced settings

1. Enable LAN interface Enable/Disable
2 Use custom DNS servers 8.8.8.8 Multiple DNS servers can be entered by clicking new entry button
near a text input field
3. Override MTU 1500 MTU (Maximum Transmission Unit) specifies the largest possible
size of a data packet
4. Use gateway metric 0 With this field you can alter the metric of that entry
6.6.2 DHCP Server
The DHCP server is the router side service that can automatically configure the TCP/IP settings of any device that
requests such a service. If you connect a device that has been configured to obtain IP address automatically the DHCP
server will lease an address and the device will be able to fully communicate with the router.

1. DHCP Enable/Disable Manage DHCP server
2. Start 100 The starting address of the range that the DHCP server can use to give out to
devices. E.g.: if your LAN IP is 192.168.2.1 and your subnet mask is
255.255.255.0 that means that in your network a valid IP address has to be in
the range of [192.168.2.1 – 192.168.2.254](192.168.2.0 and 192.168.2.255
are special unavailable addresses). If the Start value is set to 100 then the
DHCP server will only be able to lease out addresses starting from
192.168.2.100
3. Limit 150 How many addresses the DHCP server gets to lease out. Continuing on the
above example: if the start address is 192.168.2.100 then the end address
will be 192.168.2.254 (100 + 150 – 1 = 254).
4. Lease time 12 How long can a leased IP be considered valid. An IP address after the
specified amount of time will expire and the device that leased it out will
have to request for a new one. Select Hour or Minute (minimum 2min).
42
6.6.2.2 Advanced settings
You can also define some advanced options that specify how the DHCP server will operate on your LAN network.

1. Dynamic DHCP Checked/Unchecked Dynamically allocate client addresses, if set to 0 only clients present in
the ethers files are served
2. Force Checked/Unchecked Forces DHCP serving even if another DHCP server is detected on the
same network segment.
3. IP netmask You can override your LAN netmask here to make the DHCP server
think it’s serving a larger or a smaller network than it actually is.
4. DHCP-Options Additional options to be added for this DHCP server. For example with
'26,1470' or 'option:mtu, 1470' you can assign an MTU per DHCP.
Your client must accept MTU by DHCP for this to work.
6.7 Wireless
On this page you can configure your wireless settings. Depending on whether your WAN mode is set to Wi-Fi or
not, the page will display either the options for configuring an Access Point or options for configuring a connection to
some local access point.
Access Point:
Here you can see the Overview of the wireless configuration. It is divided into two main sections – device and
interface. One is dedicated to configuring hardware parameters other – software.
43
Here you can toggle the availability of the wireless radio and the physical channel frequency.
Important note: As seen in the picture you should always Save before toggling the radio on and off.
ESSID – Your wireless networks identification string. This is the name of your Wi-Fi network. When other Wi-Fi
capable computers or devices scan the area for Wi-Fi networks they will see your network with this name.
Hide ESSID – Will render your SSID hidden from other devices that try to scan the area.
6.7.1.1 Device
6.7.1.1.1 Advanced Settings
Here you can configure more advanced parameters:

1. Mode Auto, b, g, g+n Different modes provide different throughput and security
options.
2. Country Code Any ISO/IEC 3166 Selecting this will help the wireless radio configure its internal
alpha2 country code parameters to meet your countries wireless regulations.
3. Distance Optimization 100 Distance to farthest network member in meters.
4. Frag. Threshold 2346 The smallest packet size that can be fragmented and transmitted
by multiple frames. In areas were interference is a problem,
setting a lower fragment threshold might help reduce the
probability of unsuccessful packet transfers, thus increasing
speed.
5. RTS/CTS Threshold 2346 Request to send threshold. It can help resolve problems arising
when several access points are in the same area, contending.
44
6.7.1.2 Interface
6.7.1.2.1 Security
Encryption – There are many modes of encryption, a distinctive class is pointed out below.
First select an encryption method: TKIP, CCMP, TKIP&CCMP and auto. Note: Some authentication methods won’t
support TKIP (and TKIP&CCMP) encryption. After you’ve selected your encryption method, you should enter your
passphrase, which must be at least 8 characters long.
6.7.1.2.2 MAC-Filter
Filter – you can define a rule for what to do with the MAC list you’ve defined. You can either allow only the listed
MACs or allow ALL, but forbid only the listed ones.
6.7.1.2.3 Advanced settings

Separate clients – prevents Wi-Fi clients from communicating with each other on the sane subnet.
45
6.7.1.3 Client
RUT9xx can work as a Wi-Fi client (check 6.5 Chapter of this manual). Client mode is nearly identical to AP, except
for the fact that most for the options are dictated by the wireless access point that the router is connecting to. Changing
them can result in an interrupted connection to an AP.
In addition to standard options you can also click the Scan button to rescan the surrounding area and attempt to
connect to a new wireless access point.
6.8 Backup WAN

Backup WAN is function that allows you to back up your wired OR wireless connection in case they go down. At
the current moment you can only backup wired and Wi-Fi
The majority of the options consist of timing and other important parameters that help determine the health of
your primary connection. Regular health checks are constantly performed in the form of ICMP packets (Pings) on your
primary connection. When the connections state starts to change (READY->NOT READY and vice versa) a necessary
amount of failed or passed health checks has to be reached before the state changes completely. This delay is instituted
so as to mitigate “spikes” in connection availability, but it also extends the time before the backup link can be brought
up or down.

1. Enable Enable/Disable Here you can setup your backup WAN. If your
conventional WAN connection, such as wired
Ethernet or Wireless, fails, the backup link will be
enabled and take over to keep the router
connected
2. Health monitor Interval Disable/5/10/20/30/60/120 The interval at which health checks are performed
Seconds
46
3. Health monitor ICMP host(s) Disable/DNS/WAN Where to Ping for a health check. As there is no
GW/Custom definitive way to determine when the connection
to internet is down for good, you’ll have to define a
host whose availability that of the internet as a
whole.
4. Health monitor ICMP timeout 1/3/4/5/10 Seconds How long to wait for an ICMP request to come
back. Set a higher value if your connection has high
latency or high jitter (latency spikes).
5. Attempts before WAN failover 1/3/5/10/15/20 How many checks should fail for your WAN
connection to be declared DOWN for good.
6. Attempts before WAN 1/3/5/10/15/20 How many checks should pass for your WAN
recovery connection to be declared UP.
7. ICMP host 8.8.4.4 This is where the address of an ICMP host, that will
be used to check the health of your Mobile backup
link, goes. This has to be a Ping-able host.
6.8.1.1 How do I set up a backup link?

First we must pick a main link: Wired or Wi-Fi, and ensure that the link is working. Configure your WAN settings to
use that link and see whether you have internet access. If the main link is working we can continue configuring our
Backup Link.
Now, go to Backup WAN page and configure the settings to your liking. Click Save and wait until the settings are
applied.
Now in the Status -> Network Information -> WAN page there should be a status indication for the backup WAN.
If everything is working correctly you should see this:
The above picture shows the status for Backup WAN configured on a wired main link. You can now simulate a
downed link by simply unplugging your Ethernet WAN cable. When you’ve done so you should see this:
And, if you plug the cable back in you should, again, see this:
If you do not witness the above sequence, your backup link is working!
47
6.9 Firewall
In this section we will look over the various firewall features that come with RUT950.
6.9.1 General Settings

The routers firewall is a standard Linux iptables package, which uses routing chains and policies to facilitate
control over inbound and outbound traffic.

1. Enable SYN-flood protection Checked/Unchecked When checked the router becomes more resistant
against SYN-flood attacks.
2. Drop Invalid packets Checked/Unchecked A “Drop” action is performed on a packet that is
determined to be invalid
3. Input Reject/Drop/Accept DEFAULT* action that is to be performed for
packets that pass through the Input chain.
4. Output Reject/Drop/Accept DEFAULT* action that is to be performed for
packets that pass through the Output chain.
5. Forward Reject/Drop/Accept DEFAULT* action that is to be performed for
packets that pass through the Forward chain.
*DEFAULT: When a packet goes through a firewall chain it is matched against all the rules for that specific chain. If
no rule matches said packet, an according Action (either Drop or Reject or Accept) is performed.
Accept – Packet gets to continue down the next chain.
Drop – Packet is stopped and deleted.
Reject – Packet is stopped, deleted and, differently from Drop, an ICMP packet containing a message of rejection
is sent to the source of the dropped packet.
48
6.9.2 DMZ
By enabling DMZ for a specific internal host (for e.g.: your computer), you will expose that host and its services to
the routers WAN network (i.e. - internet).
6.9.3 Port Forwarding

Here you can define your own port forwarding rules.
You can use port forwarding to set up servers and services on local LAN machines. The above picture shows how
you can set up a rule that would allow a website that is being hosted on 192.168.1.109, to be reached from the outside
by entering http://routersExternalIp:12345/.

1. Name “localWebsite” Name of the rule. Used purely to make it easier to manage
rules.
2. Protocol TCP/UDP/TCP+UDP/Other Type of protocol of incoming packet.
3. External Port 1-65535 From what port on the WAN network will the traffic be
forwarded.
4. Internal IP address IP address of some computer The IP address of the internal machine that hosts some
on your LAN service that we want to access from the outside.
5. Internal port 1-65535 To what port on the internal machine would the rule
redirect the traffic.
49

When you click edit you can fine tune a rule to near perfection, if you should desire that.

1. Name “localWebsite” Name of the rule. Used purely to make it easier to manage
rules.
2. Protocol TCP/UDP/TCP+ You may specify multiple by selecting (custom) and then
UDP/ICMP/Custom entering protocols separated by space
3. Source zone LAN/VPN/WAN Match incoming traffic from this zone only
4. Source MAC address Any Match incoming traffic from these MACs only
5. Source IP address any Match incoming traffic from this IP or range only
7. Source port any Match incoming traffic originating from the given source port
or port range on the client host only
8. External IP address any Match incoming traffic directed at the given IP address only
50
9. External port 12345 Match incoming traffic directed at the given destination port or
port range on this host only
10. Internal zone LAN/VPN/WAN Redirect matched incoming traffic to the specified internal zone
11. Internal IP address 192.168.1.109 Redirect matched incoming traffic to the specified internal host
12. Internal port 80 Redirect matched incoming traffic to the given port on the
internal host
13. Enable NAT loopback Enable/Disable NAT loopback enables your local network (i.e. behind your
router/modem) to connect to a forward-facing IP address (such
as 208.112.93.73) of a machine that it also on your local
network
14. Extra arguments Passes additional arguments to iptables. Use with care!
6.9.4 Traffic Rules
The traffic rule page contains a more generalised rule definition. With it you can block or open ports, alter how
traffic is forwarded between LAN and WAN and many more things.
Field Name Explanation

1. Name Name of the rule. Used for easier rules management purpose only
2. Protocol Protocol type of incoming or outgoing packet
3. Source Match incoming traffic from this IP or range only
4. Destination Redirect matched traffic to the given IP address and destination port
5. Action Action to be taken for the packet if it matches the rule
6. Enable Self-explanatory. Uncheck to make the rule inactive. The rule will not be deleted, but it also will
not be loaded into the firewall.
7. Sort When a packet arrives, it gets checked for a matching rule. If there are several rules that match
the rule, the first one is applied i.e. the order of the rule list impacts how your firewall operates,
therefore you are given the ability to sort your list as you wish.
You can configure firewall rule by clicking edit button.
51
1. Name “Allow-DHCP-Relay” Used to make rule management easier
2. Restrict to address IPv4-only Match traffic from selected address family only
family
3. Protocol TCP/UDP/Any/ICMP/Custom Protocol of the packet that is being matched against
traffic rules.
4. Match ICMP type any Match traffic with selected ICMP type only
5. Source zone Any zone/LAN/VPN/WAN Match incoming traffic from this zone only
6. Source MAC address any Match incoming traffic from these MACs only
7. Source address any Match incoming traffic from this IP or range only
8. Source port any Match incoming traffic originating from the given source
52
port or port range on the client host only
9. Destination zone Device/Any Match forwarded traffic to the given destination zone
zone/LAN/VPN/WAN only
10. Destination address any Match forwarded traffic to the given destination IP
address or IP range only
11. Destination port 67 Match forwarded traffic to the given destination port or
port range only
12. Action Drop/Accept/Reject + chain Action to be taken on the packet if it matches the rule.
+ additional rules You can also define additional options like limiting packet
volume, and defining to which chain the rule belongs
6.9.4.1 Open Ports On Router

1. Name Open_Port_rule Used to make rule management easier
traffic rules.
3. External port 1-65535 Match incoming traffic directed at the given destination
port or port range on this host.
6.9.4.2 New Forward Rule

1. Name Forward_rule_new Used to make rule management easier
2. Source LAN/VPN/WAN Match incoming traffic from selected address family only
traffic rules.
53
6.9.4.3 Source NAT

1. Name Forward_rule_new Used to make rule management easier
traffic rules.
3. Source LAN/VPN/WAN Match incoming traffic from selected address family only
4. Destination Redirect matched traffic to the given IP address and
destination port
5. SNAT SNAT (Source Network Address Translation) rewrite
packet\'s source IP address and port
6. Enable Enable/Disable Make a rule active/inactive
You can configure firewall source NAT rule, by clicking edit button.
54
1. Name “Allow-DHCP-Relay” Used to make rule management easier
traffic rules.
3. Source zone LAN/VPN/WAN Match incoming traffic from this zone only
4. Source MAC address any Match incoming traffic from these MACs only
5. Source address any Match incoming traffic from this IP or range only
6. Source port any Match incoming traffic originating from the given source
port or port range on the client host only
7. Destination zone LAN/VPN/WAN Match forwarded traffic to the given destination zone
only
8. Destination address Select from the list Match forwarded traffic to the given destination IP
address or IP range only
55
9. Destination port any Match forwarded traffic to the given destination port or
port range only
10. SNAT IP address “10.101.1.10” Rewrite matched traffic to the given IP address
11. SNAT port “22” Rewrite matched traffic to the given source port. May be
left empty to only rewrite the IP address'
12. Extra arguments Passes additional arguments to iptables. Use with care!
6.9.5 Custom Rules

Here you have the ultimate freedom in defining your rules – you can enter them straight into the iptables
program. Just type them out into the text field ant it will get executed as a Linux shell script. If you are unsure of how to
use iptables, check the internet out for manuals, examples and explanations.
56
6.10 Static Routes
Static routes provide a way of entering custom entries in the internal routing table of the router.
Field name Value Explanation

1. Interface LAN/WAN/PPP/WAN2 The zone where the ‘Target’ resides
2. Target IP address The source of the traffic.
3. Netmask IP mask Mask that is applied to the Target to determine to what actual IP
addresses the routing rule applies
4. Gateway IP address To where the router should send all the traffic that applies to the
rule
5. Metric integer Used as a sorting measure. If a packet about to be routed fits two
rules, the one with the higher metric is applied.
Additional note on Target & Netmask: You can define a rule that applies to a single IP like this: Target - some IP;
Netmask - 255.255.255.255. Furthermore you can define a rule that applies to a segment of IPs like this: Target – some
IP that STARTS the segment; Netmask – Netmask that defines how large the segment is. E.g.:
192.168.55.161 255.255.255.255 Only applies to 192.168.55.161

192.168.55.0 255.255.255.0 Applies to IPs in range 192.168.55.0-192.168.55.255
192.168.55.240 255.255.255.240 Applies 192.168.55.240 - 192.168.55.255
192.168.55.161 255.255.255.0 192.168.55.0 - 192.168.55.255
192.168.0.0 255.255.0.0 192.168.0.0 - 192.168.255.255
57
7 Services
7.1 VRRP
7.1.1 LAN/WAN Settings
Field name Sample Explanation

1. Enable Enable/Disable Enable VRRP (Virtual Router Redundancy Protocol) for LAN
2. IP address 192.168.1.253 Virtual IP address for LAN's VRRP (Virtual Router Redundancy Protocol)
cluster
3. Virtual ID 1 Routers with same IDs will be grouped in the same VRRP (Virtual
Router Redundancy Protocol) cluster
4. Priority 100 Router with highest priority value on the same VRRP (Virtual Router
Redundancy Protocol) cluster will act as a master
7.1.2 Advanced settings
58
1. Enable Enable/Disable Enable WAN's connection monitoring
2. Ping IP address 8.8.4.4 A host to send ICMP (Internet Control Message Protocol) packets to
3. Ping interval 10 Time interval in minutes between two Pings
4. Ping timeout (sec) 1 Response timeout value, interval [1 - 9999]
5. Ping packet size 50 ICMP (Internet Control Message Protocol) packet's size, interval [0 -
1000]
6. Ping retry count 10 Failed Ping attempt’s count before determining that connection is lost
7.2 Web filter

7.2.1 Site blocking

1. Enable Enable/Disable Enable host name based websites blocking
2. Mode Whitelist/Blacklist Whitelist - allow every site on the list and block everything else.
Blacklist - block every site on the list and allow everything else
59
7.2.2 Proxy based URL content blocker

1. Enable Enable/Disable Enable proxy server based URL content blocking. Works with HTTP
protocol only
2. Mode Whitelist/Blacklist Whitelist - allow every part of URL on the list and block everything else.
Blacklist - block every part of URL on the list and allow everything else
3. Proxy port 8118 Proxy's port on the system
60
7.3 NTP
NTP configuration lets you setup and synchronize routers time.
Field name Description Notes

1. Current System time Local time of router. ---
2. Time zone Time zone of your country. ---
3. Enable NTP Enables the functionality ---
4. Update interval How often router updates ---
systems time
5. Count of time Total amount of times that If left blank - the count will be infinite
synchronizations router will do the
synchronization
6. Offset frequency Adjust the minor drift of
the clock so that it will be
more accurate
Note, that under Time Servers at least one server has to be present, otherwise NTP will not serve its purposes.
61
7.4 SNMP
SNMP settings window allows you to remotely monitor and send GSM event information to the server.
7.4.1 SNMP Settings

1. Enable SNMP service Enable/Disable Run SNMP (Simple Network Management Protocol) service on
system's start up
2. Enable remote access Enable/Disable Open port in firewall so that SNMP (Simple Network Management
Protocol) service may be reached from WAN
3. Port 161 SNMP (Simple Network Management Protocol) service's port
4. Community Public/Private/Custom The SNMP (Simple Network Management Protocol) Community is
an ID that allows access to a router's SNMP data
5. Community name custom Set custom name to access SNMP
6. Location Location Trap named sysLocation
7. Contact [email protected] Trap named sysContact
8. Name Name Trap named sysName
Variables/OID
OID Description
1. 1.3.6.1.4.1.99999.1.1.1 Modem IMEI
2. 1.3.6.1.4.1.99999.1.1.2 Modem model
3. 1.3.6.1.4.1.99999.1.1.3 Modem manufacturer
4. 1.3.6.1.4.1.99999.1.1.4 Modem revision
5. 1.3.6.1.4.1.99999.1.1.5 Modem serial number
6. 1.3.6.1.4.1.99999.1.1.6 SIM status
7. 1.3.6.1.4.1.99999.1.1.7 Pin status
8. 1.3.6.1.4.1.99999.1.1.8 IMSI
9. 1.3.6.1.4.1.99999.1.1.9 Mobile network registration status
62
10. 1.3.6.1.4.1.99999.1.1.10 Signal level
11. 1.3.6.1.4.1.99999.1.1.11 Operator currently in use
12. 1.3.6.1.4.1.99999.1.1.12 Operator number (MCC+MNC)
13. 1.3.6.1.4.1.99999.1.1.13 Data session connection state
14. 1.3.6.1.4.1.99999.1.1.14 Data session connection type
15. 1.3.6.1.4.1.99999.1.1.15 Signal strength trap
16. 1.3.6.1.4.1.99999.1.1.16 Connection type trap
7.4.2 TRAP Settings

1. SNMP Trap Enable/Disable Enable SNMP (Simple Network Management Protocol) trap
functionality
2. Host/IP 192.168.99.155 Host to transfer SNMP (Simple Network Management Protocol) traffic
to
3. Port 162 Port for trap's host
4. Community Public/Private The SNMP (Simple Network Management Protocol) Community is an
ID that allows access to a router's SNMP data
5. Signal trap Enable/Disable Trap that will be triggered if GSM signal's strength drops below
certain value
6. Signal strength -85 GSM signal's strength value in dBm, e.g. -85
7. Connection type trap Enable/Disable Trap that will be triggered when GSM connection\'s type changes,
e.g. from EDGE to HSUPA
63
7.5 VPN
7.5.1 OpenVPN
VPN (Virtual Private Network) is a method for secure data transfer through unsafe public network. This section
explains how to configure OpenVPN, which is implementation of VPN supported by the RUT950 router.
A picture below demonstrates default OpenVPN configurations list, which is empty, so you have to define a new
configuration to establish any sort of OpenVPN connection. To create it, enter desired configuration name in “New
configuration name” field, select device role from “Role” drop down list. For example, to create an OpenVPN client with
configuration name Demo, select client role, name it “Demo” and press “Add New” button as shown in the following
picture.
To see at specific configuration settings press “edit” button located in newly created configuration entry. A new
page with detailed configuration appears, as shown in the picture below (TLS client example).
There can be multiple server/client instances.
64
You can set custom settings here according to your VPN needs. Below is summary of parameters available to set:
Field name Explanation

1. Enabled Switches configuration on and off. This must be selected to make configuration active.
2. TUN/TAP Selects virtual VPN interface type. TUN is most often used in typical IP-level VPN connections,
however, TAP is required to some Ethernet bridging configurations.
3. Protocol Defines a transport protocol used by connection. You can choose here between TCP and UDP.
4. Port Defines TCP or UDP port number (make sure, that this port allowed by firewall).
5. LZO This setting enables LZO compression. With LZO compression, your VPN connection will
generate less network traffic; however, this means higher router CPU loads. Use it carefully
with high rate traffic or low CPU resources.
6. Authentication Sets authentication mode, used to secure data sessions. Two possibilities you have here:
“Static” means, that OpenVPN client and server will use the same secret key, which must be
uploaded to the router using “Static pre-shared key” option. “Tls” authentication mode uses
X.509 type certificates. Depending on your selected OpenVPN mode (client or server) you have
to upload these certificates to the router:
For client: Certificate Authority (CA), Client certificate, Client key.
For server: Certificate Authority (CA), Server certificate, Server key and Diffie-Hellman (DH)
certificate used to key exchange through unsafe data networks.
All mention certificates can be generated using OpenVPN or OpenSSL utilities on any type host
machine. Certificate generation and theory is out of scope of this user manual.
65
7. Remote host IP IP address of OpenVPN server (applicable only for client configuration).
address
8. Resolve Retry Sets time in seconds to try resolving server hostname periodically in case of first resolve failure
before generating service exception.
9. Keep alive Defines two time intervals: one is used to periodically send ICMP request to OpenVPN server,
and another one defines a time window, which is used to restart OpenVPN service, if no ICPM
request is received during the window time slice. Example Keep Alive “10 60”
10. Local tunnel IP address of virtual local network interface (applicable only for Point to Point).
endpoint
11. Remote tunnel IP address of virtual remote network interface. (Point to Point)
endpoint
12. Remote network IP address of remote network, an actual LAN network behind another VPN endpoint.
IP address
13. Remote network Subnet mask of remote network, an actual LAN network behind another VPN endpoint.
IP netmask
14. Virtual Network IP address of a virtual network (not a particular host) that will be created by TLS server.
IP address Configurable ONLY on TLS Server role.
15. Username Username for VPN authentication. Only in “Password” authentication mode.
16. Password Password for VPN authentication. Only in “Password” authentication mode.
After setting any of these parameters press “Save” button. Some of selected parameters will be shown in the
configuration list table. You should also be aware of the fact that router will launch separate OpenVPN service for every
configuration entry (if it is defined as active, of course) so the router has ability to act as server and client at the same
time.
7.5.2 IPSec
The IPsec protocol client enables the router to establish a secure connection to an IPsec peer via the Internet.
IPsec is supported in two modes - transport and tunnel. Transport mode creates secure point to point channel between
two hosts. Tunnel mode can be used to build a secure connection between two remote LANs serving as a VPN solution.
IPsec system maintains two databases: Security Policy Database (SPD) which defines whether to apply IPsec to a
packet or not and specify which/how IPsec-SA is applied and Security Association Database (SAD), which contain Key of
each IPsec-SA.
The establishment of the Security Association (IPsec-SA) between two peers is needed for IPsec communication. It
can be done by using manual or automated configuration.
Note: router starts establishing tunnel when data from router to remote site over tunnel is sent. For automatic
tunnel establishment used tunnel Keep Alive feature.
66
1. Enable IPSec Check box to enable IPSec.
2. IPSec key exchange mode Automatic Key exchange.
3. Enable NAT traversal Enable this function if client-to-client applications will be used.
4. Enable initial contact Enable this to send an INITIAL-CONTACT message.
5. Peers identifier type Choose “fqdn” or “user fqdn” accordingly to your IPSec server configuration.
6. Mode Select “Main”, “Aggressive” or "Base" mode accordingly to your IPSec server
configuration.
7. My identifier Set the device identifier for IPSec tunnel.
In case RUT has Private IP, its identifier should be its own LAN network
address. In this way, the RoadWarrior approach is possible.
8. Preshare key Specify the authentication secret *string+. Secret’s length depends on selected
algorithm, eg. 128 bit long secret is 16 characters in length, 128 bits / 8 bits
(one character) = 16.
9. Remote VPN Endpoint Set remote IPSec server IP address.
10. DPD delay If the RUT does not receive DPD-ACK message from its IPSec peer, RUT shuts
the connection down.
67
Phase 1 and Phase 2 must be configured accordingly to the IPSec server configuration, thus algorithms,
authentication and lifetimes of each phase must be identical.
Remote Network Secure Group – Set the remote network (Secure Policy Database) information. It must be LAN
network of remote IPSec host.

1. Tunnel keep alive Allows sending ICMP echo request (Ping utility) to the remote tunnel network. This
function may be used to automatically start the IPSec tunnel.
This function should be used every time.
2. Ping IP address Enter IP address to which ICMP echo requests will be sent.
3. Ping period (seconds) Set sent ICMP request period in seconds.
68
7.5.3 GRE Tunnel
GRE (Generic Routing Encapsulation RFC2784) is a solution for tunneling RFC1812 private address-space traffic
over an intermediate TCP/IP network such as the Internet. GRE tunneling does not use encryption it simply encapsulates
data and sends it over the WAN.
In the example network diagram two distant networks LAN1 and LAN2 are connected.
To create GRE tunnel the user must know the following parameters:
1. Source and destination IP addresses.

2. Tunnel local IP address
3. Distant network IP address and Subnet mask
69
1. Enable GRE Tunnel Check the box to enable the GRE Tunnel function.
2. TTL Specify the fixed time-to-live (TTL) value on tunneled packets [0-255]. The 0 is a
special value meaning that packets inherit the TTL value.
3. PMTUD Check the box to enable the Path Maximum Transmission Unit Discovery (PMTUD)
status on this tunnel.
4. Remote tunnel network Specify remote LAN Subnet address.
address
5. Remote CIDR Specify remote LAN Subnet CIDR value.
6. Local tunnel IP IP address of the local virtual tunnel interface. This IP must be in the same
network on both GRE ends, i.e. 10.0.0.1 on one end and 10.0.0.2 on another end.
7. Local tunnel CIRD Virtual tunnel CIDR
8. Remote IP address Specify remote WAN IP address.
9. MTU Specify the maximum transmission unit (MTU) of a communications protocol of a
layer in bytes.
7.5.4 L2TP
Allows setting up a L2TP server or client and should it be needed - using it with IPsec (L2TP/IPSec). Below is L2TP
server configuration example.

1. Enable L2TP Tunnel Check the box to enable the GRE Tunnel function.
2. Local IP IP Address of this device (RUT)
3. Remote IP IP address of either one or many L2TP clients.
4. Username Username to connect to L2TP (this) server
5. Password Password to connect to L2TP server
Client configuration is even simplier, which requires only Servers IP, Username and Password.
70
7.5.5 Dynamic DNS
Dynamic DNS (DDNS) is a domain name service allowing to link dynamic IP addresses to static hostname.
To start using this feature firstly you should register to DDNS service provider (example list is given in description).
You are provided with add/delete buttons to manage and use different DDNS configurations at the same time!
You can configure many different DDNS Hostnames in the main DDNS Configuration section.
To edit your selected configuration, hit Edit.
71
Field name Value Explanation
1. Enable - Enables current DDNS configuration.
2. Status - Timestamp of the last IP check or update.
3. Service 1. dydns.org Your dynamic DNS service provider selected from the list.
2. 3322.org In case your DDNS provider is not present from the ones provided,
3. no-ip.com please feel free to use "custom" and add hostname of the update URL.
4. easydns.com
5. zoneedit.com
4. Hostname RUT9xx.noip.org Domain name which will be linked with dynamic IP address.
5. Username myusername Name of the user account.
6. Password mypassword Password of the user account.
7. IP Source Public This option allows you to select specific RUT interface, and then send
Private the IP address of that interface to DDNS server. So if, for example, your
Custom RUT has Private IP (i.e. 10.140.56.57) on its WAN (3G/LTE interface),
then you can send this exact IP to DDNS server by selecting "Private",
or by selecting "Custom" and "WAN" interface. The DDNS server will
then resolve hostname queries to this specific IP.
8. IP renew interval 10 (minutes) Time interval (in minutes) to check if the IP address of the device have
changed.
9. Force IP renew 472 (minutes) Time interval (in minutes) to force IP address renew.
72
7.6 SMS Utilities
RUT950 has extensive amount of various SMS Utilities. These are subdivided into 4 sections: general SMS Utilities,
Send SMS, SMS Management and Remote Configuration.
7.6.1 SMS Utilities
You can choose your SMS Keyword (text to be sent) and authorized phone number in the main menu. You can
edit each created rule by hitting Edit button. All configuration options are listed below:
73
Field name Explanation Notes
1. Enable SMS Reboot This check box will enable and If you select Get Status, it will send routers status once
disable SMS reboot function. it has rebooted and is operational again. For Get
Status description see item No. 4 of this table.
2. SMS text SMS text which will reboot SMS text can contain letters, numbers, spaces and
router. special symbols. Capital letters also matters.
3. Sender phone number Phone number of person who You can add as many phone numbers as you need.
can reboot router via SMS Dropdown list with additional rows will show up if you
message click on “add” icon at the end of phone number row.
4. Get status Check this to receive This is both separate SMS Rule and an option under
connection status via SMS after SMS Reboot rule.
a reboot.
5. Enable SMS Status This check box will enable and SMS status is disabled by default.
disable SMS status function.
6. SMS text SMS text which will send SMS text can contain letters, numbers, spaces and
routers status. special symbols. Capital letters also matters.
can receive router status via Dropdown list with additional rows will show up if you
SMS message click on “add” icon at the end of phone number row.
8. Get Information Data state You can select which status elements to display.
Operator
Connection type
Signal Strength
Connection State
IP
9. Wireless On/Off via This check box will enable and Allows Wi-Fi control via SMS
SMS disable this function
10. Wireless on SMS text SMS text which will turn Wi-Fi SMS text can contain letters, numbers, spaces and
ON special symbols. Capital letters also matters.
11. Wireless on SMS text SMS text which will turn Wi-Fi SMS text can contain letters, numbers, spaces and
OFF special symbols. Capital letters also matters.
12. Sender Phone number Phone number of person who You can add as many phone numbers as you need.
13. Write to config Permanently saves Wi-Fi state With this setting enabled, router will keep Wi-Fi state
even after reboot.
If it is not selected, router will revert Wi-Fi state after
reboot.
14. Mobile Settings via This check box will enable and Allows cellular control via SMS
SMS disable mobile settings function
15. SMS text Key word that will precede SMS text can contain letters, numbers, spaces and
actual configuration special symbols. Capital letters also matters.
parameters
74
Mobile Settings via SMS parameters:
Parameter Value(s) Explanation

1. apn= i.e. internet.gprs Sets APN. i.e: apn=internet.gprs
2. dialnumber= i.e. *99***1# Sets dial number
3. auth_mode= none Sets authentication mode
pap
chap
4. service= auto You can add as many phone numbers as you need.
3gpreferred Dropdown list with additional rows will show up if you
3gonly click on “add” icon at the end of phone number row.
2gpreferred
2gonly
5. username= user Used only if PAP or CHAP authorization is selected
6. password= user Used only if PAP or CHAP authorization is selected
All Mobile settings can be changed in one SMS. Between each <parameter=value> pair a space symbol is
necessary.
Example: cellular apn=internet.gprs dialnumber=*99***1# auth_mode=pap service=3gonly username=user

password=user

1. 3G On/Off via SMS This check box will enable and Function disabled by default
disable this function
2. 3G on SMS text Text to turn 3G connection ON SMS text can contain letters, numbers, spaces and
special symbols. Capital letters also matters.
3. 3G off SMS text Text to turn 3G connection OFF
4. Write to config Permanently saves 3G network With this setting enabled, router will keep 3G state
state even after reboot.
If it is not selected, router will revert 3G state after
reboot.
5. Change profile via This check box will enable and Function disabled by default
SMS disable this function
6. SMS text to change Keyword that must precede SMS text can contain letters, numbers, spaces and
profile profile name special symbols. Capital letters also matters.
7. SMS text to get list of Upon receiving this SMS router
profiles will send list of created profiles
to the sender number
8. Sender Phone number Phone number of person who You can add as many phone numbers as you need.
can control this function Dropdown list with additional rows will show up if you
click on “add” icon at the end of phone number row.
Important Notes:
 3G settings must be configured correctly. If SIM card has PIN number you must enter it at “Network” > “3G”
settings. Otherwise SMS reboot function will not work.
 Sender phone number must contain country code. You can check sender phone number format by reading
the details of old SMS text massages you receiving usually.
75
7.6.2 Send SMS and SMS Management
You can send SMS from RUT WebUI. Under SMS Management you can read and delete received/stored SMS.

1. Phone number Recipients phone number to Should be preceded with country code, i.e. “+370”
send SMS to
2. Message SMS message text All special characters are allowed.
7.6.3 Remote Configuration

RUT9xx can be configured via SMS from another RUT9xx. You only have to select which configuration details are
to be sent, generate the SMS Text, type in the phone number and Serial number of the router that you wish to configure
and Send the SMS.
Total count of SMS is managed automatically. You should be aware of possible number of SMS and use this
feature at your own responsibility. It should not, generally, be used if you have high cost per SMS. This is especially
relevant if you will try to send whole OpenVPN configuration, which might acumulate ~40 SMS.
76
7.7 Hotspot
Wireless hotspot provides essential functionality for managing an open access wireless network. In addition to
standard RADIUS server authentication there is also the ability to gather and upload detailed logs on what each device
(denoted as a MAC address) was doing on the network (what sites were traversed, etc.).
7.7.1 General settings

1. Enabled Check this flag to enable hotspot functionality on the router.
2. AP IP Access Point IP address. This will be the address of the router on the hotspot network. The
router will automatically create a network according to its own IP and the CIDR number that
you specify after the slash. E.g. “192.168.2.254/24” means that the router will create a
network with the IP address 192.168.182.0, netmask 255.255.255.0 for the express purpose
of containing all the wireless clients. Such a network will be able to have 253 clients (their IP
addresses will be automatically granted to them and will range from 192.168.2.1 to
192.168.2.253).
3. Authentication External radius
mode
4. Radius server #1 The IP address of the RADIUS server that is to be used for Authenticating your wireless
clients.
77
5. Radius server #2 The IP address of the second RADIUS server.
6. Authentication port RADIUS server authentication port.
7. Accounting port RADIUS server accounting port.
8. Authentication Internal radius
mode
9. IP address or E.g.(192.168.1.1 or 192.168.1.0/24)
network of the
client
10. Authentication Without radius
mode
11. Doesn’t require any RADIUS configuration. Allows simple user connection based on
username/password.
12. Hotspot name The name of your hotspot. Will appear on the login screen.
13. Secret Key The secret key used for authenticating with the RADIUS server.
14. Protocol Either HTTP or HTTPs
7.7.2 Logging

1. Enable logging and Check this box if you want to enable wireless traffic logging. This feature will produce logs
upload which contain data on what websites each client was visiting during the time he was
connected to your hotspot.
2. Server address The IP address of the FTP server to which you want the logs uploaded.
3. Username The username of the user on the aforementioned FTP server.
4. Password The password of the user.
5. Port The TCP/IP Port of the FTP server.
78
1. Mode The mode of the schedule. Use “Fixed” if you want the uploading to be done on a specific
time of the day. Use “Interval” If you want the uploading to be done at fixed interval.
2. Weekdays This field specifies on what weekdays the uploading should be done. The entry format is
numbers from 1 to 7 separated by only commas. E.g. If you want to upload the logs on
Monday, Wednesday and Saturday you should enter “1,3,6”.
3. Interval Shows up only when “Mode” is set to Interval. Specifies the interval of regular uploads on
one specific day. E.g. If you choose 4 hours, the uploading will be done on midnight, 4:00,
8:00, 12:00, 16:00 and 20:00.
4. Hours, Minutes Shows up only when “Mode” is set to Fixed. Uploading will be done on that specific time of
the day. E.g. If you want to upload your logs on 6:48 you will have to simply enter hours: 6
and minutes: 48.
79
7.7.3 Landing Page

1. Page title Will be seen as landing page title
2. Logo image Logo seen on landing page.
3. Link title You can add an additional link, example yoursite.com
4. Link address Example http://www.yoursite.co
7.8 Auto Reboot

7.8.1 Ping Reboot
Ping Reboot function will periodically send Ping command to server and waits for echo receive. If no echo is
received router will try again sending Ping command defined number times, after defined time interval. If no echo is
received after the defined number of unsuccessful retries, router will reboot. It is possible to turn of the router
rebooting after defined unsuccessful retries. Therefore this feature can be used as “Keep Alive” function, when router
Pings the host unlimited number of times.
80
1. Enable This check box will enable or disable Ping reboot Ping Reboot is disabled by
feature. default.
2. Reboot router if no echo This check box will disable router rebooting after This check box must be
received the defined number of unsuccessful retries. unselected if you want to use
Ping Reboot feature as “Keep
Alive” function.
3. Interval between Pings Time interval in minutes between two Pings. Minimum time interval is 5
minutes.
4. Ping timeout (sec) Time after which consider that Ping has failed. Range(1-9999)
5. ICMP packet size This box allows to modify sent packet size Should be left default, unless
necessary otherwise
6. Retry count Number of times to try sending Ping to server after Minimum retry number is 1.
time interval if echo receive was unsuccessful. Second retry will be done after
defined time interval.
7. Host to Ping Server IP address or host name, which will receive If you use server host name
Ping from router instead of the IP address you
must configure DNS server first.
81
7.8.2 Periodic Reboot

1. Enable This check box will enable or disable Periodic reboot feature.
2. Days This check box will enable router rebooting at the defined days.
3. Hours, Minutes Uploading will be done on that specific time of the day
8 System
8.1 Configuration Wizard
The configuration wizard provides a simple way of quickly configuring the device in order to bring it up to basic
functionality. The wizard is comprised out of 4 steps and they are as follows:
Step 1 (Password change)
First, the wizard prompts you to change the default password. Simply enter the same password into both
Password and Confirmation fields and press Next.
82
Step 2 (Mobile Configuration)
Next we have to enter your mobile configuration. On a detailed instruction on how this should be done see the
Mobile section under Network
Step 3 (LAN)
Next, you are given the chance to configure your LAN and DHCP server options. For a detailed explanation see
LAN under Network.
83
Step 4 (Wi-Fi)
The final step allows you to configure your wireless settings in order to set up a rudimentary Access Point.
When you’re done with the configuration wizard, press Finish.
84
8.2 Configuration profiles
Router can have virtually unlimited number or configuration profiles, which you can later apply either via WebUI
or via SMS. When you add New Profile, you save current full configuration of the router.
Note: profile names cannot exceed 10 symbols.
8.3 Administration
8.3.1 General
85
1. Router name Enter your new router name.
2. Host name Enter your new host name
3. Password Enter your new administration password.
Changing this password will change SSH password as well.
4. Confirmation Re-enter your new administration password.
5. Language Website will be translated into selected language.
6. Show mobile info at login page Show operator and signal strength at login page.
7. Restore to default Router will be set to factory default settings
Important notes:
The only way to gain access to the web management if you forget the administrator password is to reset the
device factory default settings. Default administrator login settings are:
User Name: admin
Password: admin01
8.3.2 Troubleshoot

1. System log level Debug level should always be used, unless instructed otherwise.
2. Save log in Default RAM memory should always be used unless instructed otherwise.
3. Include GSMD information Default setting – enabled should be used, unless instructed otherwise.
4. Include PPPD information Default setting – disabled should be used, unless instructed otherwise.
5. Include Chat script Default setting – enabled should be used, unless instructed otherwise.
86
information
6. System Log Provides on-screen System logging information. It does not, however, substitute
troubleshooting file that can be downloaded from System -> Backup and Firmware
menu.
7. Kernel Log Provides on-screen Kernel logging information. It does not, however, substitute
troubleshooting file that can be downloaded from System -> Backup and Firmware
menu.
8. Troubleshoot Downloadable archive, that contains full router configuration and all System log files.
8.3.3 Backup

1. Backup archive Download current router settings file to personal computer. This file can be loaded
to other RUT900 with same Firmware version in order to quickly configure it.
2. Restore from backup Upload and restore router settings file from personal computer.
8.3.4 Access Control
87
1. Enable SSH access Check box to enable SSH access functionality.
2. Remote SSH access If check box is selected – user can access the router via SSH from outside (WAN).
3. Port Port to listen for SSH access.
4. Enable HTTP access Check box to enable HTTP access functionality.
5. Enable remote SSH If check box is selected users can access the router via the HTTP WEB Interface from the
access outside (WAN).
6. Enable remote If check box is selected users can access the router via the HTTPS WEB Interface from the
HTTPS access outside (WAN).
Note: The router has 2 users: “admin” for WebUI and “root” for SSH. When logging in via SSH use “root”.
8.3.5 Diagnostics

1. Host Enter server IP address or hostname.
2. Ping Utility used to test the reachability of a host on an Internet IP network and to measure the round-
trip time for messages sent from the originating host to a destination server. Server echo
response will be shown after few seconds if server is accessible.
3. Traceroute Diagnostic tool for displaying the route (path) and measuring transit delays of packets across an
Internet IP network. Log containing route information will be shown after few seconds.
4. Nslookup Network administration command-line tool for querying the Domain Name System (DNS) to
obtain domain name or IP address mapping or for any other specific DNS record. Log containing
specified server DNS lookup information will be shown after few seconds.
88
8.3.6 MAC Clone

1. WAN MAC address Enter new WAN MAC address.
2. Wireless MAC address Enter new Wireless MAC address.
8.4 User scripts

Advanced users can insert their own commands to execute at the end of the boot process.
8.5 Safe mode

Router contains two firmware images in its internal flash memory. One is master firmware which is the default
firmware on is constantly used by the user. Another is safe mode firmware which plays the role of the backup to the
master firmware.
Safe mode firmware has most function of master firmware but to reduce its size some function were removed.
Removed functions are: Wireless Hotspot, VRRPD, SNMP, Web Filter
Safe mode firmware can be recognized from different logo and reduced menu in the WebUI. The sole purpose of
safe mode firmware is to allow the user to update master firmware so all configuration options are removed. To make
safe mode useful it is strongly recommended to back up configuration of master firmware when the user is satisfied
with the setup. After configuration backup is created it can be tested by requesting safe mode.
89
8.6 Firmware
Keep settings – when check box is selected router will keep saved user configuration settings after firmware
upgrade. When check box is not selected all router settings will be restored to factory defaults after firmware upgrade.
When upgrading firmware, you can choose settings that you wish to keep after the upgrade. This function is useful
when firmware is being upgraded via Internet (remotely) and you must not lose connection to the router afterwards. In
such case: cellular settings should be kept.
FW image – router firmware upgrade file.
Warning: Do not ever remove router power supply and do not press reset button during upgrade process! This
will totally damage your router and it won’t be accessible. If you have any problems related to firmware upgrade you
should always consult with local dealer.
8.7 Restore point

Allows restoring firmware and configuration from restore point.
8.8 Reboot
Reboot router by pressing button “Reboot”.
90
9 Functionality not listed in menu
9.1 SMS by HTTP POST/GET

It is possible to read and send SMS by using valid HTTP POST/GET syntax. Use web browser or any other
compatible software to submit HTTP POST/GET string to router. Router must be connected to GSM network when using
“SMS send” feature.
9.1.1 Syntax of HTTP POST/GET string
HTTP POST/GET string Explanation

http://{IP_ADDRESS} /cgi-bin/sms_read?number={MESSAGE_INDEX} Read message
/cgi-bin/sms_send?number={PHONE_NUMBER}&text={MESSAGE_TEXT} Send message
/cgi-bin/sms_delete?number={MESSAGE_INDEX} Delete message
/cgi-bin/sms_list? List all messages
/cgi-bin/sms_ total? Number of
messages in
memory
Note: parameters of HTTP POST/GET string are in capital letters inside curly brackets. Curly brackets (“, -”) are not
needed when submitting HTTP POST/GET string.
9.1.2 Parameters of HTTP POST/GET string
Parameter Explanation
1. IP_ADDRESS IP address of your router
2. MESSAGE_INDEX SMS index in memory
3. PHONE_NUMBER Phone number of the message receiver.
Note: Phone number must contain country code. Phone number format is:
00{COUNTRY_CODE}{RECEIVER_NUMBER}.
E.g.: 0037062312345 (370 is country code and 62312345 is receiver phone number)
4. MESSAGE_TEXT Text of SMS. Note: Maximum number of characters per SMS is 160. You cannot send
longer messages. It is suggested to use alphanumeric characters only.
After every executed command router will respond with return status.
9.1.3 Possible responses after command execution
Response Explanation
1. OK Command executed successfully
2. ERROR An error occurred while executing command
3. TIMEOUT No response from the module received
4. WRONG_NUMBER SMS receiver number format is incorrect or SMS index number is incorrect
5. NO MESSAGE There is no message in memory by given index
6. NO MESSAGES There are no stored messages in memory
9.1.4 HTTP POST/GET string examples
http://192.168.1.1/cgi-bin/sms_read?number=3
http://192.168.1.1/cgi-bin/sms_send?number=0037061212345&text=test
http://192.168.1.1/cgi-bin/sms_delete?number=4
http://192.168.1.1/cgi-bin/sms_list
http://192.168.1.1/cgi-bin/sms_total
91
10 Device Recovery
The following section describes available option for recovery of malfunctioning device. Usually device can become
unreachable due to power failure during firmware upgrade or if core files were wrongly modified in the file system.
Teltonika’s router does offer several ways to recover from these situations
10.1 Reset button

Reset button is located on the back panel of the device. Reset button has several functions:
Reboot the device. After the device has started if the reset button is pressed for up to 4 seconds
the device will reboot. Start of the reboot will be indicated by flashing of all 5 signal strength LEDs
together with green connection status LED.
Reset to defaults. After the device has started if the reset button is pressed for at least 5 seconds
the device will reset all user changes to factory defaults and reboot. To help the user to determine how
long should reset button be pressed signal strength LEDs count elapsed time. All 5 lit LEDs mean that 5
seconds have elapsed and reset button can be released. Start of the reset to defaults will be indicated
by flashing of all 5 signal strength LEDs together with red connection status LED.
SIM PIN on the main SIM card (SIM1) is the only parameter that is kept after reset to defaults.
10.2 Safemode
Router contains two firmware images in its internal flash memory. One is master firmware which is the default
firmware on is constantly used by the user. Another is safemode firmware which plays the role of the backup to the
master firmware.
Safemode firmware has most function of master firmware but to reduce its size some function were removed.
Removed functions are:
 Wireless Hotspot
 VRRPD
 SNMP
 Web Filter
Safemode firmware can be recognized from different logo and reduced menu in the WebUI. The sole purpose of
safemode firmware is to allow the user to update master firmware so all configuration options are removed. To make
safemode useful it is strongly recommended to back up configuration of master firmware when the user is satisfied with
the setup (described in Safemode section). After configuration backup is created it can be tested by requesting
safemode.
10.3 Bootloader’s WebUI

Bootloader also provides a way to recover the router from damaged firmware. To make it easy for the user
bootloader has its own webserver that can be accessed with any web browser.
Bootloader’s webserver can be started:
Automatically. It happens when bootloader does not detect neither master nor safemode
firmware. Flashing all 4 Ethernet LEDs indicate that bootloader’s webserver has started.
92
Manually. Bootloader’s webserver can be requested by holding reset button for 3 seconds while
powering the device on. Flashing all 4 Ethernet LEDs indicate that bootloader’s webserver has started.
Bootloader’s WebUI can be accessed by typing this address in the web browser:
http://192.168.1.1/index.html
Note: it may be necessary to clear web browser’s cache and to use incognito/anonymous window to access
bootloader’s WebUI
11 Glossary:
WAN – Wide Area Network is a telecommunication network that covers a broad area (i.e., any network that links
across metropolitan, regional, or national boundaries). Here we use the term WAN to mean the external network that
the router uses to reach the internet.
LAN – A local area network (LAN) is a computer network that interconnects computers in a limited area such as a
home, school, computer laboratory, or office building.
DHCP – The Dynamic Host Configuration Protocol (DHCP) is a network configuration protocol for hosts on Internet
Protocol (IP) networks. Computers that are connected to IP networks must be configured before they can communicate
with other hosts. The most essential information needed is an IP address, and a default route and routing prefix. DHCP
eliminates the manual task by a network administrator. It also provides a central database of devices that are connected
to the network and eliminates duplicate resource assignments.
ETHERNET CABLE – Refers to the CAT5 UTP cable with an RJ-45 connector.
AP – Access point. An access point is any device that provides wireless connectivity for wireless clients. In this
case, when you enable Wi-Fi on your router, your router becomes an access point.
DNS – Domain Name Resolver. A server that translates names such as www.google.lt to their respective IPs. In
order for your computer or router to communicate with some external server it needs to know it’s IP, its name
“www.something.com” just won’t do. There are special servers set in place that perform this specific task of resolving
names into IPs, called Domain Name servers. If you have no DNS specified you can still browse the web, provided that
you know the IP of the website you are trying to reach.
ARP – Short for Adress Resolution Protocol, a network layer protocol used to convert an IP address into a physical
address (called a DLC address), such as an Ethernet address.
PPPoE – Point-to-Point Protocol over Ethernet. PPPoE is a specification for connecting the users on an Ethernet to
the internet through a common broadband medium, such as DSL line, wireless device or cable modem.
DSL – digital subscriber line - it is a family of technologies that provide internet access by transmitting digital data
using a local telephone network which uses the public switched telephone network.
NAT – network address translation – an internet standard that enables a local-area network (LAN) to use one set
of IP addresses for internet traffic and a second set of addresses for external traffic.
LCP – Link Control Protocol – a protocol that is part of the PPP (Point-to-Point Protocol). The LCP checks the
identity of the linked device and either accepts or rejects the peer device, determines the acceptable packet size for
transmission, searches for errors in configuration and can terminate the link if the parameters are not satisfied.
93
BOOTP – Bootstrap Protocol – an internet protocol that enables a diskless workstation to discover its own IP
address, the IP address of a BOOTP server on the network, and a file to be loaded into memory to boot the machine.
This enables the workstation to boot without requiring a hard or floppy disk drive.
TCP – Transmission Control Protocol – one of the main protocols in TCP/IP networks. Whereas the IP protocol
deals only with packets, TCP enables two hosts to establish a connection and exchange streams of data. TCP guarantees
delivery of data and also guarantees that packets will be delivered in the same order in which they were sent.
TKIP – Temporal Key Integrity Protocol – scrambles the keys using hashing algorithmand, by adding an integrity-
checking feature, ensure that the keys haven’t been tampered with.
CCMP – Counter Mode Cipher Block Chaining Message Authentication Code Protocol – encryption protocol
designed for Wireless LAN products that implement the standards of the IEEE 802.11i amendment to the original
IEEE802.11 standard. CCMP is an enchanged data cryptographic encapsulation designed for data confidentiality and
based upon the Counter Mode with CBC-MAC (CCM) of the AES (Advanced Encyprion Standard) standard.
MAC – Media Access Control – hardware address that uniquely identifies each node of a network. In IEEE 802
networks, the Data Link Control (DCL) layer of the PSO Reference Model is divided into two sub-layers: the Logical Link
Control (LLC) layer and the Media Access Control layer. The MAC layer interfaces directly with the network medium.
Consequently, each different type of network medium requires a different MAC layer.
DMZ – Demilitarized Zone – a computer or small subnetwork that sits between a trusted internal network, such as
a corporate private LAN, and an untrusted external network, such as the public internet.
UDP – User Datagram Protocol – a connectionless protocol that, like TCP, runs on top of IP networks. Provides
very few error recovery services, offering instead a direct way to send and receive datagrams over IP network.
VPN – Virtual Private Network – a network that is constructed by using public wires — usually the Internet — to
connect to a private network, such as a company's internal network.
VRRP – Virtual Router Redundancy Protocol - an election protocol that dynamically assigns responsibility for one
or more virtual router(s) to the VRRP router(s) on a LAN, allowing several routers on a multiaccess link to utilize the
same virtual IP address.
GRE Tunnel – Generic Routing Encapsulation - a tunneling protocol developed by Cisco Systems that can
encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol
internetwork.
PPPD – Point to Point Protocol Daemon – it is used to manage network connections between two nodes on Unix-
like operating systems. It is configured using command-line arguments and configuration files.
SSH – Secure SHell - a program to log into another computer over a network, to execute commands in a remote
machine, and to move files from one machine to another. It provides strong authentication and secure communications
over insecure channels.
VRRPD – Virtual Router Redundancy Protocol – it is designed to eliminate the single point of failure associated
with statically routed networks by automatically providing failover using multiple LAN paths through alternate routers.
SNMP – Simple Network Management Protocol - a set of protocols for managing complex networks. SNMP works
by sending messages, called protocol data units (PDUs), to different parts of a network.
94

User Manual: WWW - Westlake.co - Uk UK Sales: 0800 298 8011

Uploaded by

Copyright:

Available Formats

User Manual: WWW - Westlake.co - Uk UK Sales: 0800 298 8011

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

User Manual: WWW - Westlake.co - Uk UK Sales: 0800 298 8011

Uploaded by

Copyright:

Available Formats

USER MANUAL

www.westlake.co.uk UK Sales : 0800 298 8011

The device is not water-resistant. Keep it dry.

Device is powered by low voltage +9V DC power adaptor.

Do not mount or service the device during a thunderstorm.

To avoid mechanical damages to the device it is recommended to transport it packed in a

1.1.8 Electrical, Mechanical & Environmental

2.1.1 Front Panel and Back Panel

1,2,3 LAN Ethernet ports 1 LTE auxiliary antenna connector

SIM 1 (primary) SIM 2 (secondary)

2. Attach LTE main and Wi-Fi antennas.

7. If you choose to configure manually here’s what you do:

WAN LAN Mobile Backup link

4.1 Powering the device from higher voltage

5.1 System Information

5.2 Network Information

Field Name Sample Value Explanation

Client mode information

Field Name Sample Value Explanation

5.2.1.6 OpenVPN Client (must be updated)

Field Name Sample Value Explanation

Field Name Sample Value Explanation

5.2.1.8 Client information

Field Name Sample Value Explanation

Field Name Sample Value Explanation

Field Name Sample Value Explanation

Field Name Sample Value Explanation

5.6 Realtime Graphs

Field Name Explanation

Field Name Sample value Explanation

6.1.2 Mobile Data On Demand

Field name Possible values Explanation

6.2 SIM Management

6.3 Network Operators

6.4 Mobile Data Limit

6.4.1 Data Connection Limit Configuration

Field Name Sample value Explanation

Filed name Sample Explanation

Filed name Sample Explanation

Field name Sample value Explanation

Field name Sample value Explanation

6.6.1.1 General Setup

Field name Sample value Explanation

Field name Sample value Explanation

6.6.2.1 General Setup

Field Name Sample value Explanation

Field Name Sample Value Explanation

Here you can configure more advanced parameters:

Field name Sample value Explanation

6.7.1.2.3 Advanced settings

6.8 Backup WAN

Field Name Sample value Explanation

6.8.1.1 How do I set up a backup link?

6.9.1 General Settings

Field Name Sample value Explanation

Accept – Packet gets to continue down the next chain.

Drop – Packet is stopped and deleted.

6.9.3 Port Forwarding

Field Name Sample value Explanation