Classification: Reference: Date:

AT15-003f NTB15-037f August 10, 2018

VERSA SEDAN, VERSA NOTE, AND SENTRA;

CVT VALVE BODY REPLACEMENT WITH CONFIRMED DTC
This bulletin has been amended. A TCM P/N was added to 2015 Sentra in Table A.
No other changes were made. Discard all previous versions of this bulletin.

APPLIED VEHICLES: 2012 – 2017 Versa Sedan (N17)

2014 – 2017 Versa Note (E12)
2013 – 2017 Sentra (B17)
APPLIED TRANSMISSION: CVT (RE0F11A)
NOTE: Does not apply to 2017 Sentra equipped with MR16DDT turbo engine.

IF YOU CONFIRM
 If one or more of the DTCs listed in the DTC Chart on page 2 are present in the
Transmission Control Module (TCM).
And
 No other DTCs are present other than what are listed in the DTC Chart.

ACTION
1. Go to Repair Overview on page 3 to determine which repairs to perform to the applied
vehicle being worked on.

IMPORTANT: The purpose of “ACTION” (above) is to give you a quick idea of the work
you will be performing. You MUST closely follow the entire Service Procedure as it contains
information that is essential to successfully completing the repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/40
DTC Chart

DTC CODE DTC/CIRCUIT DIAGNOSIS

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A
P0740 TORQUE CONVERTER
P0743 TORQUE CONVERTER
P0846 TRANSMISSION FLUID PRESSURE SEN/SW B
P0847 TRANSMISSION FLUID PRESSURE SEN/SW B
P0848 TRANSMISSION FLUID PRESSURE SEN/SW B
P0962 PRESSURE CONTROL SOLENOID A
P0963 PRESSURE CONTROL SOLENOID A
P0998 SHIFT SOLENOID F
P0999 SHIFT SOLENOID F
P0966 PRESSURE CONTROL SOLENOID B
P0967 PRESSURE CONTROL SOLENOID B
P099B SHIFT SOLENOID G
P099C SHIFT SOLENOID G

2/40 NTB15-037f
Repair Overview
Applied Vehicle has
one or more DTCs in
the DTC Chart

All Applied Vehicles:

Replace the control valve
assembly (valve body)

Repairs in addition to
valve body replacement:

 2013-2017 Sentra
 2014-2017 Versa NOTE  2012 Versa Sedan
 2013-2017 Versa Sedan

 Erase Memory Data

Reprogram the TCM  Conform CVTF Deteriortn
 Auxiliary gearbox clutch
point learning

END

3/40 NTB15-037f
SERVICE PROCEDURE

OIL PAN, CONTROL VALVE (Valve Body)

Exploded View

JSDIA6707GB

1. Transaxle assembly 2. O-ring 3. Control valve

4. Manual plate 5. Washer 6. O-ring
7. Strainer 8. Oil pan gasket 9. Magnet
10. Oil pan 11. Drain plug gasket 12. Drain plug
13. Overflow tube
: Apply petroleum jelly

: Always replace after every disassembly.

: Apply CVT fluid

: Nꞏm (kg-m, ft-lb)

: Nꞏm (kg-m, in-lb.)

Valve Body: Removal and Installation

REMOVAL
1. Disconnect battery negative terminal.
2. Remove engine under cover.

4/40 NTB15-037f
3. Disconnect the CVT unit harness connector.
4. Remove the drain plug and overflow tube, and then drain the CVT fluid.
CAUTION:
Use caution when looking into the drain hole as there is the risk of fluid entering the eye.
5. Remove the drain plug gasket from the drain plug.
6. Remove the oil pan mounting bolts ( ), and then remove
the oil pan and oil pan gasket.

: Vehicle front

7. Remove the magnets from the oil pan.

 Clean magnets.
 Clean CVT oil pan.
 Reinstall magnets to the oil pan.

8. Remove the strainer bolts , and then remove the strainer

from the control valve.
 Discard the strainer. A new one will be used during
assembly.

9. Remove the nut and washer , and then remove

manual plate .
CAUTION:
To remove nut, fix manual plate with flat-blade
screwdriver
(B).
10. Press the CVT unit harness connector into the transaxle
case.
CAUTION:
Never damage the CVT unit harness connector.
NOTE:
Clean around the CVT unit harness connector to prevent
foreign materials from entering into the transaxle case.

11. Remove the control valve bolts , and then remove the
control valve from the transaxle case.
CAUTION:
• Never drop the control valve and manual valve.

5/40 NTB15-037f
 INSTALLATION

1. Install the control valve, and then tighten control valve bolts
to the specified torque.
CAUTION:
• Never pinch the harness between the control valve
and the transaxle case.
• Never drop the control valve and manual valve.

2. Install the manual plate and washer , and then tighten

nut to the specified torque.
CAUTION:
To tighten nut, fix manual plate with flat-blade
screwdriver.

 Reassembly Torque: 22.1 N•m (2.3 kg-m, 16 ft-lb)

3. Install the new strainer , and then tighten the strainer

bolts to the specified torque.

4. Install oil pan (with oil pan gasket) to transaxle case and
temporarily tighten oil pan bolts ( ).

CAUTION:
Never reuse oil pan gasket.

: Vehicle front

5. Tighten the oil pan bolts to specification in the order shown.

: Vehicle front

6. Tighten the overflow tube to the specified torque.

CAUTION:
If it is not tightened to the specified torque, the tube
may be damaged.
7. Connect the CVT unit harness connector.
8. Connect battery negative terminal.
9. Fill with CVT fluid from overflow tube to the specified level.
Refer to ESM for further information.
10. Install the drain plug and drain plug gasket to oil pan.
CAUTION:
Never reuse drain plug gasket.

11. Reinstall engine under cover.

6/40 NTB15-037f
TCM Reprogramming
IMPORTANT: Before starting the TCM reprogram procedure, make sure:
 ASIST on the CONSULT PC has been synchronized (updated) to the current
date.
 All CONSULT-III plus (C-III plus) software updates (if any) have been installed.
NOTE:
 TCM reprogramming applies to 2014-2017 Versa NOTE, 2013-2017 Sentra, and
2013-2017 Versa Sedan only.
 2012 Versa Sedan does NOT require reprogramming.
 For more information, see Repair Overview on page 3.

1. Connect the plus Vehicle Interface (plus VI) to the vehicle.

CAUTION: Make sure the plus VI is securly connected. If the plus VI connection is
loose during reprogramming, the process will be interrupted and the TCM may be
damaged.

2. Connect the AC Adapter to the CONSULT PC.

CAUTION: Be sure to connect the AC Adapter. If the CONSULT PC battery voltage
drops during reprogramming, the process will be interrupted and the TCM may be
damaged.

3. Connect the GR8, set to “Power Supply” mode, to the vehicle battery.
CAUTION: Be sure the GR8 is connected securely to the battery. Make sure the
battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery
voltage goes out of this range during reprogramming, the TCM may be damaged.

4. Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range
of the CONSULT PC and the VI.
CAUTION: Make sure to turn OFF all external Bluetooth® devices. If Bluetooth®
signal waves are within range of the CONSULT PC and the VI during
reprogramming, reprogramming may be interrupted and the TCM may be damaged.

5. Turn the ignition ON with the engine OFF.

 The engine must not start or run during the reprogramming procedure.

6. Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC,
blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc.
IMPORTANT: Make sure to turn OFF all vehicle electrical loads. Make sure the
battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery
voltage goes out of this range during reprogramming, the TCM may be damaged.

7. Turn ON the CONSULT PC.

8. Select/open C-III plus.

7/40 NTB15-037f
9. Wait for the plus VI to be recognized.

 Serial number will display when the plus VI is recognized.

Step 9:
plus VI is
recognized

Figure 1

10. Select Re/programming, Configuration.

Step
10

Figure 2

8/40 NTB15-037f
11. Use arrows (if needed) to view and read all precautions.
12. Check the box confirming the precautions have been read.
13. Select Next.

Step Step
12 11

Step
13

Figure 3

14. If the screen in Figure 4 displays, select Automatic Selection(VIN).

 If the screen in Figure 4 does not display, skip to step 15.

Step
14

Example

Figure 4

9/40 NTB15-037f
 15. Make sure VIN or Chassis # matches the vehicle’s VIN.

16. If the correct VIN is displayed, select Confirm.

Step 15:
Verify here

Step
16

Figure 5

17. Select Confirm.

Step
17

Figure 6

10/40 NTB15-037f
18. Select TRANSMISSION.

Step
18

Figure 7

19. Select Reprogramming.

Step
19

Figure 8

11/40 NTB15-037f
20. Follow the on-screen instructions; maintain the following conditions:
a. Ignition ON, with the engine OFF.
b. Press the Brake.
c. Press accelerator between ¼ and ½.
d. Put shift selector in R.

21. Select Start.

Step
21

Figure 9

22. When COMPLETED is displayed, select Next.

Step
22

Figure 10

12/40 NTB15-037f
23. Operate the ignition per the on screen instructions.

Ignition status

Timer

Progress display

Figure 11

24. When OK is displayed, select Next.

Step
24

Figure 12

13/40 NTB15-037f
25. Move the shift selector to P, then select Next.

Step
25

Figure 13

26. Operate the shift selector per the on-screen instructions.

a. Move the shift selector; P>R>N>D>P
b. Confirm the center display meter indicates the correct selector position.

27. Select Next.

Step
26

Step
27

Figure 14

14/40 NTB15-037f
28. Find the TCM Part Number
(see Figure 15) and write it on
the repair order.
NOTE: This is the current Part
Number (P/N).

Step Step
28 31
29. Compare the P/N you wrote
down to the numbers in the
Current TCM Part Number
column in Table A below.

Figure 15

30. Comparison results:

 If there is a match, continue with the reprogramming procedure.
 If there is not a match, reprogramming is not needed. Skip to ERASE MEMORY
DATA on page 29.
Table A
MODEL MODEL YEAR CURRENT TCM PART NUMBER: 31036 -
3SG0A, 3SG0B, 3SG0C, 3SG9B, 3SG9C,
2013
3SR0A, 3SR0B, 3SR0C, 3SR9B, 3SR9C
2014 9AM2A, 9AM2B, 9AM2C, 9AM9B, 9AM9D, 9AM9E
Sentra 4AT0A, 4AT0B, 4AT0C, 4AT0D,
2015
4AT9A, 4AT9D, 4AT8E, 4AT9E
2016 4AF6A, 4AF6B, 4AF9D
2017 4FY0A, 4FY0B, 4FY0C
2013 9KB1B, 9KB1C, 9KB1D, 9KB9E, 9KJ9E
2014 3BE0A, 3BE0B, 3BE9A, 3BE9C
Versa Sedan 2015 9KE0A, 9KE0B, 9KE0C, 9KE9C, 9KE9E
2016 9KN0A, 9KN0B, 9KN0C, 9KN8D, 9KN8E
2017 9KN2A, 9KN2B, 9KN2C
2014 3VB2A, 3VB2B, 3VB2C, 3VB8C, 3VB9D
2015 3VB6A, 3VB9A, 3VB9B, 3VB9C, 3VB9E, 3WC9D
Versa NOTE
2016 3VB4A, 3VB4B, 3VB4C, 3VB4D, 3VB7A, 3WC9E
2017 9ME0A, 9ME0B, 9ME0C

31. Select Save.

15/40 NTB15-037f
32. Use arrows (if needed) to view and read all precautions.
33. Check the box confirming the precautions have been read.
34. Select Next.

Step Step
33 32

Step
34

Figure 16

NOTE: If you get the screen in Figure 17 and it is blank (no reprogramming listed), it
means there is no reprogramming available for this vehicle. Close C-III plus and refer
back to ASIST for further diagnosis.

TRANSMISSION

Figure 17

16/40 NTB15-037f
35. Read the Current Part Number and Part Number After Reprogramming. They
should be different.

36. Select Next.

Step 35
These numbers
should be
different

Step
36

Figure 17a

17/40 NTB15-037f
37. Make sure OK is highlighted green (battery voltage must be between 12.0 and 15.5
Volts).

38. Select Next.

IMPORTANT: Battery voltage must stay between 12.0 and 15.5 Volts during
reprogramming or TCM reprogramming may be interrupted and TCM may be damaged.

Monitor battery
voltage here

Step
37

Step
38

Figure 18

39. Make sure OK is highlighted green for all Judgements then select Start.

Monitor battery
voltage here

Step

EXAMPLE
39

Figure 19

18/40 NTB15-037f
40. Select USA/CANADA Dealers.

41. Select OK.

Step
40

Step
41

Figure 20

NOTE:
 The above screen may not display if the CONSULT PC has remained ON since the
last reprogramming.
 If the CONSULT PC is not connected to the Internet, the screen in Figure 21 will
display.

Figure 21

19/40 NTB15-037f
42. Enter Username and Password.

 Before reprogramming will start, you will be required to enter your User Name and
Password.
 The CONSULT PC must be connected to the Internet (Wi-Fi or cable).
 If you do not know your User Name and Password, contact your Service
Manager.

43. Select Submit.

 There will be a short pause while the username and password are
authenticated.

 Once authentication completes, TCM reprogramming will automatically begin

and the screen in Figure 23 on the next page will be displayed.

Step
42

Step
43

Figure 22

20/40 NTB15-037f
44. Wait for both progress bars to complete.

Step
44

Figure 23

45. When the screen in Figure 24 displays, the reprogramming is complete.

NOTE: If the screen in Figure 24 does not display (which indicates reprogramming did
not complete), refer to the information on the next page.
46. Disconnect the battery charger (GR8) from the vehicle.
47. Select Next.

Step
47

Figure 24

NOTE: Additional steps/operations are required before C-III plus will provide the final
reprogramming confirmation report. Continue with the reprogramming procedure on
page 23.
21/40 NTB15-037f
If reprogramming does not complete and the “!?” symbol displays as shown in
Figure 25:

 Check battery voltage (12.0 –

15.5V).
 Ignition ON, engine OFF.
 External Bluetooth® devices are
OFF.
 All electrical loads are OFF.
 Select Retry and follow the on
screen instructions.

NOTE: Retry may not go

through on first attempt and can
be selected more than once.
Figure 25

If reprogramming does not complete and the “X” symbol displays as shown in
Figure 26:

 Do not disconnect the plus VI

or shut down C-III plus if
reprogramming does not
complete.
 Check battery voltage (12.0 –
15.5V).
 CONSULT A/C adapter is
plugged in.
 Ignition ON, engine OFF.
 Transmission in Park.
 All C-III plus / plus VI cables are
securely connected.
Figure 26
 All C-III plus updates are
installed.
 Select Home, and then restart
the reprogram procedure from
the beginning.

22/40 NTB15-037f
48. Confirm the Transmission Fluid temperature judgment is OK, then select Next.

 If the judgment is NG, drive the vehicle to warm the transmission until the judgment
changes to OK.

Step
48

Figure 27

23/40 NTB15-037f
49. Follow the on-screen
instructions; maintain
the following conditions:

a. Parking brake set.

b. Ignition ON, with the
engine OFF.
c. Press the Brake.
d. Press accelerator
between ¼ and ½.
e. Put shift selector in
R. Step
50
Figure 28
50. Select Erase DTC.

51. Follow the on-screen

instructions; maintain
the following conditions:
a. Parking brake set.
b. Ignition ON, with the
engine OFF.
Step
c. Fully depress the 52
accelerator.
d. Put shift selector in
R.

52. Select Start.

Figure 29

24/40 NTB15-037f
53. When COMPLETED is displayed, select Next.

Step
53

Figure 30

54. Operate the ignition per the on-screen instructions.

Ignition status

Timer

Progress display

Figure 31

25/40 NTB15-037f
55. When OK is displayed, select Next.

Step
55

Figure 32

56. Operate the shift selector per the on-screen instructions.

a. Move the shift selector to P; then move P>R>N>D>P
b. Confirm the center display meter indicates the correct selector position.

57. Select Next.

Step Step
56 57

Figure 33

26/40 NTB15-037f
58. Erase all DTCs as follows:

a. Turn the ignition OFF.

b. Turn the Ignition ON.

c. Wait for DTC erase to complete.

59. Select Next.

Turn ignition ON > OFF > ON

ON

Step
59

Figure 34

27/40 NTB15-037f
60. Verify the before and after part numbers are different.

61. Print a copy of this screen (Figure 35) and attach it to the repair order.

62. Select Confirm.

Step
60

Step
61

Step
62

Figure 35

NOTE: If you cannot print the above screen:

a. Select Screen Capture.
b. Name the file.
c. Save the file in My Documents.
 A copy of the screen is now saved in the CONSULT PC. It can be retrieved and
printed at a later time.

28/40 NTB15-037f
ERASE MEMORY DATA

NOTE: This procedure is for all Applied Vehicles.

63. Navigate C-III plus to the screen shown in Figure 36.

 Diagnosis (All Systems) > TRANSMISSION > Work support

64. Select ERASE MEMORY DATA.

65. Select Start.

Step
64 Step
65

Figure 36

29/40 NTB15-037f
 66. Follow the on-screen
instructions; maintain
the following conditions:
a. Parking brake set.
b. Ignition ON, with the
engine OFF.
Step
c. Fully depress the 67
accelerator.
d. Put shift selector in
R.

67. Select Start.

Figure 37

68. When the Current status

changes to
COMPLETED, select
End.

Step
68

Figure 38

69. Move the shift selector to P, and then turn the ignition OFF.

70. Turn the ignition ON, and then confirm P and N display by moving the shift selector in
those positions.

30/40 NTB15-037f
CONFORM CVTF DETERIORTN

NOTE: This procedure is for all Applied Vehicles.

71. Navigate C-III plus to the screen shown in Figure 39.

 Diagnosis (All Systems) > TRANSMISSION > Work support
72. Select CONFORM CVTF DETERIORTN.
73. Select Start.

Step
72

Step
73

Figure 39

74. Select Start.

Step
74

Figure 40

31/40 NTB15-037f
75. Select Clear.

Step
75

Figure 41

76. Select Yes.

Step
76

Figure 42

32/40 NTB15-037f
77. When CVFT DETERIORATION DATE changes to “0”, select End.

Step
77

Figure 43

78. Start the engine.

79. Set the parking brake.

80. Turn OFF the A/C.

81. Bring the engine to normal operating temperature range.

82. Confirm the CVT fluid temperature is over 122°F (50°C).

33/40 NTB15-037f
Auxiliary gearbox clutch point learning

NOTE: This procedure is for all Applied Vehicles.

83. Navigate C-III plus to the screen shown in Figure 44.

 Diagnosis (All Systems) > TRANSMISSION > Work support

84. Select Auxiliary gearbox clutch point learning.

Or
 If this feature is not available in the vehicle that is being repaired, skip to Manual
Auxiliary gearbox clutch point learning on page 38.

85. Select Start.

Step
85
Step
84

Figure 44

34/40 NTB15-037f
86. Follow the on-screen instructions in Figure 45, and then select Start.

Step
86

Figure 45

87. With the brake pedal still applied, shift the CVT selector lever into the D position.
 Figure 46 (below) will be displayed after shifting into D position.
NOTE: The Current status will show EXECUTING (Figure 46), but until the vehicle is
shifted into the D position, Auxiliary gearbox clutch point learning will not begin.

Step
87

Figure 46

35/40 NTB15-037f
88. Continue to depress the brake pedal until the Current status shows “Completed” as
shown in Figure 48 at the bottom of this page.
NOTE: This may take several minutes to complete.

Figure 47

89. When Completed is displayed, select End.

Step
89

Figure 48

90. Shift the vehicle into “P”, turn ignition OFF and release the brake pedal.

91. Perform Auxiliary Gearbox Clutch Point Learning (steps 83 to 89) one additional time
(a total of two times).

36/40 NTB15-037f
Erase DTCs

NOTE: This procedure is for all Applied Vehicles.

92. Use C-III plus to erase any transmission DTCs that may have stored.

93. Turn OFF C-III plus.

94. Disconnect C-III plus and the plus VI from the vehicle.

95. Verify the CVT operates normally and no abnormal noises are heard during a test drive.

37/40 NTB15-037f
MANUAL AUXILIARY GEARBOX CLUTCH POINT LEARNING

CAUTION: If clutch touch point learning is not performed, you may feel shift shock
when the auxiliary transmission shifts.

NOTE: This manual procedure is only needed if the auto procedure is not available in
C-III plus.

a. Start the engine and warm up the CVT fluid to 50°C (122°F).
NOTE: Confirm the CVT fluid temperature by “FLUID TEMP” in “Data Monitor”.
b. Turn the air conditioner OFF.
c. Shift the CVT selector lever to the P position, turn the ignition OFF and then wait for
5 seconds.
d. Start the engine and allow it to idle for 5 seconds.
e. Turn the ignition OFF and then wait for 30 seconds.
f. Perform Step “e” to Step “f” two more times (Total: Three times).
g. Start the engine.
h. Allow engine to idle for 30 seconds.
i. Shift the CVT selector lever to D position.
j. Accelerate the vehicle from 0 km/h (0 MPH) to 65 km/h (40 MPH) at low throttle
(0.5/8 – 1/8).
k. Decelerate the vehicle to 30 km/h (18 MPH) or less without using brakes.
l. Stop the vehicle and shift the selector lever to P position.
m. Turn the ignition OFF and wait for 5 seconds or more.
n. Restart the engine.
o. Perform Step “j” to Step “o” four times (Total: Five times).
p. Shift the selector lever to D position.
q. Accelerate the vehicle from 0 km/h (0 MPH) to 45 km/h (28 MPH) at low throttle
(0.5/8 – 1/8).
r. Stop the vehicle and shift the selector lever to P position.
s. Turn the ignition OFF for 5 seconds or more and then restart the engine.
t. Perform Steps “q” to Step “t” four times (Total: Five times).
u. Drive the vehicle and check that no shock occurs while shifting gears.

38/40 NTB15-037f
PARTS INFORMATION

All Vehicles
DESCRIPTION PART # QUANTITY
GASKET (CVT drain plug) 11026-JA00A 1
NS-3 CVT Fluid
(All vehicles listed below except 999MP-NS300P (1) as needed
2012 MY Versa Sedan)
NS-2 CVT Fluid (2012 MY Versa Sedan only) 999MP-NS200P (1) as needed
(1) NS-2 and NS-3 CVT Fluids can be ordered through the Nissan Maintenance Advantage
program: Phone: 877-NIS-NMA1 (877-647-6621). Website order via link on dealer
portal www.NNAnet.com and click on the “Maintenance Advantage” link.

Versa Sedan MY 2013-2017 and Versa NOTE MY 2014-2017

DESCRIPTION PART # QUANTITY
KIT-CONTROL VALVE 3170E-X428B 1
Kit Includes
VALVE ASSY - CONTROL -- 1
GASKET - OIL PAN -- 1
STRAINER ASSY-OIL -- 1

Versa Sedan MY 2012

DESCRIPTION PART # QUANTITY
VALVE ASSY - CONTROL 31705-3JX8A 1
STRAINER ASSY-OIL 31728-3JX0B 1
GASKET - OIL PAN 31397-3JX0A 1

Sentra MY 2013-2017
DESCRIPTION PART # QUANTITY
KIT-CONTROL VALVE 3170E-X428C 1
Kit Includes
VALVE ASSY - CONTROL -- 1
GASKET - OIL PAN -- 1
STRAINER ASSY-OIL -- 1

39/40 NTB15-037f
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION PFP OP CODE SYM DIAG FRT
Replace Control Valve (1) JD48AA HC 32 (2)
(1) Refer to the Electronic Parts Catalog (FAST) and use the applicable Control Valve
Assembly Part Number (31705-*****) as the Primary Failed Part.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate
time.

And if needed on the same line

OPERATION OP CODE FRT

Reprogram TCM JE99AA (1)
(1) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate
time.

40/40 NTB15-037f