Scribd
Upload
190 views3 pages

DC Motor Speed & Direction Controller With Brake Using Mc33035

Uploaded by

Mile Martinov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
190 views3 pages

DC Motor Speed & Direction Controller With Brake Using Mc33035

Uploaded by

Mile Martinov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

DC MOTOR SPEED & DIRECTION CONTROLLER WITH BRAKE USING MC33035

3AMP DC Motor speed and direction controller using MC33035 IC from on semiconductor, though the
MC33035 was designed to control brushless DC motor , it may also be used to control DC brush type
motors. MC33035 driving a Mosfets based H-Bridge affording minimal parts count to operate a brush
type motor. On board potentiometer provided for speed control, slide switch for direction control and
brake, On board jumper available to enable the chip. The controller function is normal manner with a
PWM frequency of approximately 25Khz. Motor speed is controlled by adjusting the voltage presented
to the no inverting input of the error amplifier establishing the PWM's slice or reference level. Cycle by
cycle current limiting of the motor current is accomplished by sensing the voltage across the shunt
resistor to ground of the H-bridge. The overcurrent sense circuit makes it possible to reverse the
direction of the motor, using normal forward/reverse switch, on the fly and not have to completely stop
before reversing.

·SUPPLY 12-18V DC
·Load Up to 3Amps, 5Amps with large size heat sink on Mosfets BOM
SR. QNTY. REF. DESC.
·On Board Potentiometer for Speed Control
1 1 CN1 2 Pin Connector
·Slide Switch ( SW1) for Brake
2 1 C1 5K6PF
·Slide Switch (SW2) for Direction Control 3 1 C2 1KPF
·Jumper (J1) Provided to Enable the chip 4 1 C3 10uF/25V
·LED (D1) Fault Indicator 5 1 C4 0.1uF
·LED (D2) Power Indicator 6 2 D1,D2 LED
·CN1 , Supply 12-18V DC 7 1 J1 ENABLE
·MG1 Motor Connections 8 1 MG1 2 Pin Screw Terminal
9 2 P1,R4 10K
10 2 Q1,Q2 IRF9540
11 2 Q3,Q4 IRF540
12 2 R1,R7 1K
13 1 R2 1K
14 1 R3 20K
15 2 R5,R6 22E
16 1 R8 0.1E/3W
17 1 R9 1K5
18 2 SW1,SW2 Slide Switch
19 1 U1 MC33035P
20 1 Socket 24 Pin IC Socket

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.openfry.com ©
www.twovolt.com
DC MOTOR SPEED & DIRECTION CONTROLLER WITH BRAKE USING MC33035

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.openfry.com ©
www.twovolt.com
DC MOTOR SPEED & DIRECTION CONTROLLER WITH BRAKE USING MC33035

0 7 0 0 5
www.twovolt.com www.youtube.com/thetwovolt Author Rajkumar Sharma www.openfry.com ©
www.twovolt.com

You might also like