Fosroc Nitocote EP405: Solvent-Free Epoxy Resin Coating For Water Retaining and Water Excluding Structures Uses

Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

7

CI/SfB: Pn6
July 2014

Fosroc® Nitocote EP405 constructive solutions

Solvent-free epoxy resin coating for water


retaining and water excluding structures

Uses
c 370
For lining and waterproofing potable water retaining structures* Fosroc Ltd
and surfaces subject to contact with foodstuffs. The cured film Drayton Manor Business Park, Coleshill Road, Tamworth, B78 3TL, UK

is corrosion, chemical and abrasion resistant and is suitable 09


for application to basements, tunnels, tanks, silos, reservoirs*, DoP: UK9-36
water treatment works*, breweries, dairies and meat and food 370-CPR-0845
processing plants. The cured film is non toxic and meets the Nitocote EP405
requirements of BS 6920. (* See ‘Limitations’.)
EN1504-2: Surface protection systems methods
1.3, 2.2, 5.1, 6.1 and 8.2
Advantages
Abrasion resistance < 3000 mg
 High build application Permeability to CO2 > 50 m
 Can be applied directly to mild steel and concrete Permeability to water Class 1 < 5 m
 Smooth, glossy, easy to clean surface vapour
 Corrosion, chemical and abrasion resistant Capillary absorption and < 0.1 kg/(m2h0.5)
 Can be applied to damp surfaces permeability to water
 Waterproof Chemical resistance Average decrease < 50%
Shore Hardness
 Water Regulations Advisory Service - approved product
Impact resistance Class III: > 20 Nm
 Provides protection against water vapour and ground
gases such as radon, carbon dioxide and methane. Adhesion strength by > 2.0 (rigid trafficked
pull-off test systems)

Description Fire Classification A2


Dangerous substances Complies with 5.3
Nitocote EP405 is a two-part, solvent free, epoxy resin material.
It is supplied in pre-measured quantities ready for site mixing
and use and is available in blue and white.

Standards compliance
Nitocote EP405 meets the requirements of BS 6920, the Water
Regulations Advisory Service, tests of effect on water quality.

Page 1
7
CI/SfB: Pn6
July 2014

Fosroc® Nitocote EP405

Properties Application

Volume solids: 100% Number of coats: 2


Viscosity: Pourable, spreadable liquid Theoretical application
Pot life - rate per coat: 0.2 litres per m²
@ 20°C: 30 to 40 minutes Theoretical wet film
@ 35°C: 10 to 15 minutes thickness per coat: 200 microns
The local Fosroc office should be consulted for resistance to Overcoating times -
specific chemicals. @ 5°C: 18 to 48 hours
@ 20°C: 6 to 18 hours
Application instructions @ 30°C: 3 to 9 hours
Fully cured *-
All coating work to be carried out in accordance with the @ 5°C: 14 days
relevant sections of BS6150:2006, Painting of Buildings - @ 20°C: 7 days
Code of Practice. @ 30°C: 7 days
Preparation
* see Limitations
Concrete surfaces
The minimum application temperature is 5°C.
All surfaces must be smooth, sound and free from contamination
All surfaces should be treated with two coats of Nitocote
and areas of standing water. Concrete surfaces must be fully
EP405. The thoroughly mixed material should be applied with
cured, laitance free and free from any traces of shuttering
a suitable stiff nylon type brush.
release oils and curing compounds.
The first coat must be firmly applied and be well scrubbed
All surfaces should then be grit blasted to remove all foreign
into the surface, ensuring a uniform coating with a wet film
matter and open up blow-holes and provide a suitable key
thickness not less than 200 microns. The first coat should be
for Nitocote EP405.
allowed to dry for not less than 6 hours and not more than
All blow holes and imperfections should be filled with Nitomortar 18 hours at 20°C.
FC. Consult the local data sheet for pot life and overcoating time. The second coat should be applied exactly as above, again
Spalled surfaces, those containing large blow holes or surface achieving a wet film thickness not less than 200 microns.
imperfections should be repaired or rendered using a Fosroc For ease of overcoating, it is recommended that the first coat
approved repair mortar or render. Contact the local Fosroc be white and the second coat blue, or vice-versa.
office for further advice on suitable materials.
For cold weather working, it is recommended that Nitocote
Steel surfaces EP405 be stored in a heated building and removed immediately
All surfaces should be grit blasted to meet the requirements before use, as workability deteriorates and curing times
of BS 7079 Sa2.5.. The lining work should be programmed so increase at lower temperatures.
that newly cleaned steel is coated as soon as possible before Cleaning
the formation of rust or scale.
Nitocote EP405 should be removed from tools and equipment
Mixing with Fosroc Solvent 102 immediately after use. Cured material
can only be removed mechanically.
Thoroughly stir the contents of the base can. Empty the entire
contents of the hardener can into the base container and mix
Estimating
thoroughly until a uniform consistency is obtained, taking
particular care to scrape the sides and bottom of the container. Nitocote EP405 is supplied in 2.5 kg packs (1.5 litres) each
It is recommended that mechanical mixing be employed, using yielding 3 m² per kg per coat (5 m² per litre).
a Jiffy mixer on a heavy duty, slow speed electric drill.
The coverage figure is theoretical — due to wastage factors
and the variety and nature of substrates, practical coverage
figures may be substantially reduced.

constructive solutions
Page 2
7
CI/SfB: Pn6
July 2014

Fosroc® Nitocote EP405

Limitations Precautions
Nitocote EP405 should not be applied over existing coatings. Health and safety
Application should not be undertaken if the temperature is For further information refer to appropriate Product Safety
below 5°C, or is 5°C and falling, nor when the prevailing Datasheet.
relative humidity exceeds 90%.
Disposal
Although Nitocote EP405 may be applied to damp concrete,
there must be no standing or running water. To eliminate risk of exotherm, only mix product when ready
for use and then apply without delay. Any unused residue
Nitocote EP405 is not colour stable when exposed to direct should be poured on to a disposable impervious surface to
sunlight nor when in contact with some chemicals. On curing allow cure before disposal.
Nitocote EP405, the final colour can vary with curing conditions,
and in adverse conditions such as low temperature and/or high Fire
humidity, a white bloom may appear on the surface. However, Nitocote EP405 is non-flammable.
this does not affect the performance of the coating.
For further information, refer to Product Safety Data Sheet.
* Before commencing application it is important to ensure that
Nitocote EP405 meets all current compliance requirements. Fosroc Solvent 102 is flammable. Keep away from sources
Note: Nitocote EP405 meets the requirements of BS 6920 of ignition. No Smoking. In the event of fire, extinguish with
the United Kingdom Water Regulations Advisory Scheme CO2 or foam. Do not use a water jet.
but not Regulation 31 of the Water Supply (Water Quality)
Regulations 2000. Flash point
In accordance with WRAS listing, when Nitocote EP405 is Fosroc Solvent 102: 33°C
used in contact with potable water, curing conditions are 21
days at 7oC. For further information, refer to the Product Safety
Data Sheet.
Storage
All products have a shelf life of 18 months if kept in a dry store
between 5°C and 30°C in the original, unopened containers.
Material from different batches shall be stored separately.
If stored at high temperatures the shelf life may be reduced.

Fosroc and Nitocote are trademarks of


Fosroc International Limited

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recom-
mendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control over
where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or not in
accordance with any advice, specification, recommendation of information given by it.

Fosroc Limited
Drayton Manor Business Park
Coleshill Road, Tamworth, telephone: fax: email:
Staffordshire B78 3TL. UK +44 0 (1827) 262222 +44 0 (1827) 262444 enquiryuk@fosroc.com

www.fosroc.com Certificate number FM 610

Page 3

You might also like