NFS2-640/E: Fire Alarm Control Panel Installation Manual

Fire Alarm Control Panel
NFS2-640/E
Installation Manual
Document 52741 Rev: P9

5/13/19 ECN: 18-305
Fire Alarm & Emergency Communication System Limitations
While a life safety system may lower insurance rates, it is not a substitute for life and property insurance!
An automatic fire alarm system—typically made up of smoke Heat detectors do not sense particles of combustion and alarm
detectors, heat detectors, manual pull stations, audible warning only when heat on their sensors increases at a predetermined rate
devices, and a fire alarm control panel (FACP) with remote notifica- or reaches a predetermined level. Rate-of-rise heat detectors may
tion capability—can provide early warning of a developing fire. Such be subject to reduced sensitivity over time. For this reason, the rate-
a system, however, does not assure protection against property of-rise feature of each detector should be tested at least once per
damage or loss of life resulting from a fire. year by a qualified fire protection specialist. Heat detectors are
An emergency communication system—typically made up of an designed to protect property, not life.
automatic fire alarm system (as described above) and a life safety IMPORTANT! Smoke detectors must be installed in the same
communication system that may include an autonomous control room as the control panel and in rooms used by the system for the
unit (ACU), local operating console (LOC), voice communication, connection of alarm transmission wiring, communications, signal-
and other various interoperable communication methods—can ing, and/or power. If detectors are not so located, a developing fire
broadcast a mass notification message. Such a system, however, may damage the alarm system, compromising its ability to report a
does not assure protection against property damage or loss of life fire.
resulting from a fire or life safety event. Audible warning devices such as bells, horns, strobes, speak-
The Manufacturer recommends that smoke and/or heat detectors ers and displays may not alert people if these devices are located
be located throughout a protected premises following the on the other side of closed or partly open doors or are located on
recommendations of the current edition of the National Fire another floor of a building. Any warning device may fail to alert peo-
Protection Association Standard 72 (NFPA 72), manufacturer's ple with a disability or those who have recently consumed drugs,
recommendations, State and local codes, and the alcohol, or medication. Please note that:
recommendations contained in the Guide for Proper Use of System • An emergency communication system may take priority over a
Smoke Detectors, which is made available at no charge to all fire alarm system in the event of a life safety emergency.
installing dealers. This document can be found at http:// • Voice messaging systems must be designed to meet intelligibility
www.systemsensor.com/appguides/. A study by the Federal requirements as defined by NFPA, local codes, and Authorities
Emergency Management Agency (an agency of the United States Having Jurisdiction (AHJ).
government) indicated that smoke detectors may not go off in as
many as 35% of all fires. While fire alarm systems are designed to • Language and instructional requirements must be clearly dis-
provide early warning against fire, they do not guarantee warning or seminated on any local displays.
protection against fire. A fire alarm system may not provide timely or • Strobes can, under certain circumstances, cause seizures in
adequate warning, or simply may not function, for a variety of people with conditions such as epilepsy.
reasons: • Studies have shown that certain people, even when they hear a
Smoke detectors may not sense fire where smoke cannot reach fire alarm signal, do not respond to or comprehend the meaning
the detectors such as in chimneys, in or behind walls, on roofs, or of the signal. Audible devices, such as horns and bells, can have
on the other side of closed doors. Smoke detectors also may not different tonal patterns and frequencies. It is the property
sense a fire on another level or floor of a building. A second-floor owner's responsibility to conduct fire drills and other training
detector, for example, may not sense a first-floor or basement fire. exercises to make people aware of fire alarm signals and
Particles of combustion or “smoke” from a developing fire may instruct them on the proper reaction to alarm signals.
not reach the sensing chambers of smoke detectors because: • In rare instances, the sounding of a warning device can cause
• Barriers such as closed or partially closed doors, walls, chim- temporary or permanent hearing loss.
neys, even wet or humid areas may inhibit particle or smoke A life safety system will not operate without any electrical power. If
flow. AC power fails, the system will operate from standby batteries only
• Smoke particles may become “cold,” stratify, and not reach the for a specified time and only if the batteries have been properly
ceiling or upper walls where detectors are located. maintained and replaced regularly.
• Smoke particles may be blown away from detectors by air out- Equipment used in the system may not be technically compatible
lets, such as air conditioning vents. with the control panel. It is essential to use only equipment listed for
service with your control panel.
• Smoke particles may be drawn into air returns before reaching
the detector. Telephone lines needed to transmit alarm signals from a premises
to a central monitoring station may be out of service or temporarily
The amount of “smoke” present may be insufficient to alarm smoke disabled. For added protection against telephone line failure,
detectors. Smoke detectors are designed to alarm at various levels backup radio transmission systems are recommended.
of smoke density. If such density levels are not created by a devel-
oping fire at the location of detectors, the detectors will not go into The most common cause of life safety system malfunction is inad-
alarm. equate maintenance. To keep the entire life safety system in excel-
lent working order, ongoing maintenance is required per the
Smoke detectors, even when working properly, have sensing limita- manufacturer's recommendations, and UL and NFPA standards. At
tions. Detectors that have photoelectronic sensing chambers tend a minimum, the requirements of NFPA 72 shall be followed. Envi-
to detect smoldering fires better than flaming fires, which have little ronments with large amounts of dust, dirt, or high air velocity require
visible smoke. Detectors that have ionizing-type sensing chambers more frequent maintenance. A maintenance agreement should be
tend to detect fast-flaming fires better than smoldering fires. arranged through the local manufacturer's representative. Mainte-
Because fires develop in different ways and are often unpredictable nance should be scheduled as required by National and/or local fire
in their growth, neither type of detector is necessarily best and a codes and should be performed by authorized professional life
given type of detector may not provide adequate warning of a fire. safety system installers only. Adequate written records of all inspec-
Smoke detectors cannot be expected to provide adequate warning tions should be kept.
of fires caused by arson, children playing with matches (especially Limit-D2-2016
in bedrooms), smoking in bed, and violent explosions (caused by
escaping gas, improper storage of flammable materials, etc.).
2 NFS2-640 Installation — P/N 52741:P9 5/13/19

Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be con- Like all solid state electronic devices, this system may operate
nected to the fire alarm control panel. Disconnect all sources of erratically or can be damaged when subjected to lightning induced
power before servicing. Control unit and associated equipment may transients. Although no system is completely immune from lightning
be damaged by removing and/or inserting cards, modules, or inter- transients and interference, proper grounding will reduce suscepti-
connecting cables while the unit is energized. Do not attempt to bility. Overhead or outside aerial wiring is not recommended, due to
install, service, or operate this unit until manuals are read and an increased susceptibility to nearby lightning strikes. Consult with
understood. the Technical Services Department if any problems are anticipated
CAUTION - System Re-acceptance Test after Software or encountered.
Changes: To ensure proper system operation, this product must be Disconnect AC power and batteries prior to removing or inserting
tested in accordance with NFPA 72 after any programming opera- circuit boards. Failure to do so can damage circuits.
tion or change in site-specific software. Re-acceptance testing is Remove all electronic assemblies prior to any drilling, filing,
required after any change, addition or deletion of system compo- reaming, or punching of the enclosure. When possible, make all
nents, or after any modification, repair or adjustment to system cable entries from the sides or rear. Before making modifications,
hardware or wiring. All components, circuits, system operations, or verify that they will not interfere with battery, transformer, or printed
software functions known to be affected by a change must be 100% circuit board location.
tested. In addition, to ensure that other operations are not inadver-
tently affected, at least 10% of initiating devices that are not directly Do not tighten screw terminals more than 9 in-lbs. Over-tighten-
affected by the change, up to a maximum of 50 devices, must also ing may damage threads, resulting in reduced terminal contact
be tested and proper system operation verified. pressure and difficulty with screw terminal removal.
This system meets NFPA requirements for operation at 0-49º C/ This system contains static-sensitive components. Always
32-120º F and at a relative humidity 93% ± 2% RH (non-condens- ground yourself with a proper wrist strap before handling any cir-
ing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the sys- cuits so that static charges are removed from the body. Use static
tem's standby batteries and the electronic components may be suppressive packaging to protect electronic assemblies removed
adversely affected by extreme temperature ranges and humidity. from the unit.
Therefore, it is recommended that this system and its peripherals Units with a touchscreen display should be cleaned with a dry,
be installed in an environment with a normal room temperature of clean, lint free/microfiber cloth. If additional cleaning is required,
15-27º C/60-80º F. apply a small amount of Isopropyl alcohol to the cloth and wipe
Verify that wire sizes are adequate for all initiating and indicating clean. Do not use detergents, solvents, or water for cleaning. Do
device loops. Most devices cannot tolerate more than a 10% I.R. not spray liquid directly onto the display.
drop from the specified device voltage. Follow the instructions in the installation, operating, and pro-
gramming manuals. These instructions must be followed to avoid
damage to the control panel and associated equipment. FACP
operation and reliability depend upon proper installation.
Precau-D2-11-2017
FCC Warning
WARNING: This equipment generates, uses, and can radi- Canadian Requirements
ate radio frequency energy and if not installed and used in This digital apparatus does not exceed the Class A limits for
accordance with the instruction manual may cause interfer- radiation noise emissions from digital apparatus set out in
ence to radio communications. It has been tested and found the Radio Interference Regulations of the Canadian Depart-
to comply with the limits for Class A computing devices pur- ment of Communications.
suant to Subpart B of Part 15 of FCC Rules, which is
designed to provide reasonable protection against such Le present appareil numerique n'emet pas de bruits radio-
interference when devices are operated in a commercial electriques depassant les limites applicables aux appareils
environment. Operation of this equipment in a residential numeriques de la classe A prescrites dans le Reglement sur
area is likely to cause interference, in which case the user le brouillage radioelectrique edicte par le ministere des
will be required to correct the interference at his or her own Communications du Canada.
expense.
HARSH™, NIS™, and NOTI•FIRE•NET™ are all trademarks; and Acclimate® Plus™, eVance®, FlashScan®, FAAST Fire Alarm Aspiration Sensing Technology®,
Honeywell®, Intelligent FAAST®, NOTIFIER®, ONYX®, ONYXWorks®, SWIFT®, VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc.
Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered
trademark of The Mozilla Foundation.
©2019 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.
NFS2-640 Installation — P/N 52741:P9 5/13/19 3

Software Downloads
In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent
upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we
strongly recommend that you download the most current version of software for each product prior to commissioning any system.
Contact Technical Support with any questions about software and the appropriate version for a specific application.
Documentation Feedback
Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about our online
Help or printed manuals, you can email us.
Please include the following information:
• Product name and version number (if applicable)
• Printed manual or online Help
• Topic Title (for online Help)
• Page number (for printed manual)
• Brief description of content you think should be improved or corrected
• Your suggestion for how to correct/improve documentation
Send email messages to:
[email protected]
Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical
Services.

Table of Contents
Section 1: About This Manual ......................................................................................................................................... 7
1.1: Standards and Other Documents .......................................................................................................................................................................7
1.1.1: UL 864 9th and 10th Edition ..................................................................................................................................................................7
1.2: Related Documents ............................................................................................................................................................................................8
1.3: Cautions and Warnings ......................................................................................................................................................................................9
Section 2: System Overview........................................................................................................................................... 10
2.1: System Description ..........................................................................................................................................................................................10
2.1.1: Standard Features..................................................................................................................................................................................10
2.1.2: Options..................................................................................................................................................................................................10
2.1.3: System Limitations ...............................................................................................................................................................................10
2.2: System Components ........................................................................................................................................................................................11
2.2.1: Basic Equipment...................................................................................................................................................................................11
2.2.2: Control Panel Circuit Board ................................................................................................................................................................11
2.2.3: Main Power Supply (CPS-24/E)...........................................................................................................................................................11
2.2.4: Circuit Board Components ...................................................................................................................................................................13
2.3: System Cabinets...............................................................................................................................................................................................15
2.4: Compatible Equipment ...................................................................................................................................................................................15
Section 3: Installation ..................................................................................................................................................... 18
3.1: Preparing for Installation .................................................................................................................................................................................18
3.1.1: Standards and Codes.............................................................................................................................................................................18
3.2: Installation Checklist .......................................................................................................................................................................................19
3.3: Mounting a Cabinet .........................................................................................................................................................................................19
3.4: Laying Out Equipment in Cabinet and Chassis...............................................................................................................................................20
3.5: Installing the Control Panel .............................................................................................................................................................................24
3.5.1: Control Panel Circuit Board & Keypad/Display Unit ..........................................................................................................................24
3.5.2: Using NCA-2 as Primary Display ........................................................................................................................................................25
3.5.3: Using the NCD as Primary Display on the NFS2-640 .........................................................................................................................25
3.6: Mounting Option Boards .................................................................................................................................................................................25
3.6.1: Option Boards in the NFS2-640/E Chassis ..........................................................................................................................................25
3.6.2: Option Boards in CHS-4L ....................................................................................................................................................................26
3.6.3: Option Boards on BMP-1 in Dress Panels ...........................................................................................................................................28
3.6.4: Transmitter Module TM-4....................................................................................................................................................................28
3.6.5: Loop Expander Module ........................................................................................................................................................................28
3.6.6: Network Communications Module.......................................................................................................................................................29
3.6.7: DVC Digital Voice Command..............................................................................................................................................................29
3.7: Connecting the Power Cables ..........................................................................................................................................................................30
3.7.1: Overview...............................................................................................................................................................................................30
3.7.2: Connecting the Control Panel to AC Power .........................................................................................................................................31
3.7.3: Checking AC Power .............................................................................................................................................................................31
3.7.4: Installing and Connecting the Batteries................................................................................................................................................31
3.7.5: External DC Power Output Connections..............................................................................................................................................32
3.7.6: Accessories DC Power Output Connections ........................................................................................................................................32
3.8: NAC Connections and Releasing Circuits.......................................................................................................................................................33
3.8.1: Stat-X Devices .....................................................................................................................................................................................34
3.8.2: FSA-8000 Wiring: ................................................................................................................................................................................34
3.9: Output Relay Connections ...............................................................................................................................................................................35
3.10: Backup-Alarm Switches ................................................................................................................................................................................35
3.11: UL Power-limited Wiring Requirements .......................................................................................................................................................36
3.11.1: Labeling Modules and Circuits...........................................................................................................................................................36
3.12: Installing EIA-485 Devices ...........................................................................................................................................................................37
3.13: Installing Remote Printers and/or CRT..........................................................................................................................................................37
3.13.1: Custom Cable Fabrication ..................................................................................................................................................................37
3.13.2: Installing and Configuring the PRN Series Printer.............................................................................................................................37
3.13.3: Installing and Configuring a Keltron Printer ......................................................................................................................................38
3.13.4: Installing and Configuring a CRT-2 ...................................................................................................................................................39
3.13.5: Connecting Multiple Printers, CRTs, or CRT/PRN Combination .....................................................................................................41
3.14: Wiring a Signaling Line Circuit (SLC)..........................................................................................................................................................42
3.15: Connecting a PC for Off-Line Programming ................................................................................................................................................43

Table of Contents
Section 4: Applications................................................................................................................................................... 44
4.1: Overview..........................................................................................................................................................................................................44
4.2: Devices Requiring External Power Supervision..............................................................................................................................................44
4.3: NFPA 72 Central or Remote Station Fire Alarm System (Protected Premises Unit) ......................................................................................44
4.4: Central Station Fire Alarm System Canadian Requirements...........................................................................................................................46
4.5: NFPA 72 Proprietary Fire Alarm Systems .......................................................................................................................................................47
4.6: Fire/Security Applications ..............................................................................................................................................................................47
4.6.1: General Operation.................................................................................................................................................................................47
4.6.2: Installing a Security Tamper Switch.....................................................................................................................................................47
4.6.3: Receiving Unit ......................................................................................................................................................................................48
4.6.4: Programming ........................................................................................................................................................................................48
4.6.5: Wiring for Proprietary Security Alarm Applications ...........................................................................................................................48
4.7: Releasing Applications ....................................................................................................................................................................................49
4.7.1: Overview...............................................................................................................................................................................................49
4.7.2: Programming ........................................................................................................................................................................................49
4.7.3: Connecting a Releasing Device to the Control Panel...........................................................................................................................49
4.7.4: Connecting a Releasing Device to the FCM-1 Module........................................................................................................................51
4.7.5: Connecting Releasing Devices to the FCM-1-REL Control Module...................................................................................................53
4.7.6: Connecting an NBG-12LRA Agent Release-Abort Station .................................................................................................................54
Section 5: Testing the System ...................................................................................................................................... 55
5.1: Acceptance Test ...............................................................................................................................................................................................55
5.2: Periodic Testing and Service............................................................................................................................................................................55
5.3: Operational Checks..........................................................................................................................................................................................55
5.4: Battery Checks and Maintenance ....................................................................................................................................................................55
Appendix A: Power Supply Calculations ...................................................................................................................... 57
A.1: Calculating AC Branch Circuit Current..........................................................................................................................................................57
A.2: Calculating the System Current Draws ..........................................................................................................................................................57
A.2.1: Calculating the Maximum Secondary Power Fire Alarm Current Draw.............................................................................................59
A.3: Calculating the Battery Requirements ............................................................................................................................................................60
A.3.1: Calculating the Battery Capacity .........................................................................................................................................................60
A.3.2: Calculating the Battery Size ................................................................................................................................................................60
Appendix B: Electrical Specifications ........................................................................................................................... 61
B.1: Electrical Specifications..................................................................................................................................................................................61
B.2: Wire Requirements..........................................................................................................................................................................................62
Appendix C: Canadian Applications.............................................................................................................................. 64
C.1: Standalone Application ...................................................................................................................................................................................64
C.1.1: NFS2-640/E with KDM-R2 .................................................................................................................................................................64
C.1.2: NFS2-640/E with NCA-2.....................................................................................................................................................................64
C.2: Network Applications .....................................................................................................................................................................................64
C.3: Automatic Alarm Signal Silence .....................................................................................................................................................................64
C.4: Annunciator Applications................................................................................................................................................................................64
C.5: Releasing Devices ...........................................................................................................................................................................................64
C.6: Ancillary Devices ............................................................................................................................................................................................64
C.7: Isolating NACs with Audio Isolator Modules.................................................................................................................................................64
C.7.1: Description of Modules........................................................................................................................................................................64

Section 1: About This Manual
1.1 Standards and Other Documents
 This Fire Alarm Control Panel complies with the following NFPA standards:
• NFPA 12 CO2 Extinguishing Systems
• NFPA 12A Halon 1301 Extinguishing Systems
• NFPA 13 Sprinkler Systems
• NFPA 15 Water Spray Systems
• NFPA 16 Foam/Water Deluge and Foam/Water Spray Systems
• NFPA 17 Dry Chemical Extinguishing Systems
• NFPA 17A Wet Chemical Extinguishing Systems
• NFPA 70 National Electrical Code
• NFPA 72 Central Station Fire Alarm Systems (Automatic, Manual and Waterflow) Protected Premises Unit (requires Notifier
UDACT/UDACT-2).
• NFPA 72 Local (Automatic, Manual, Waterflow and Sprinkler Supervisory) Fire Alarm Systems.
• NFPA 72 Auxiliary (Automatic, Manual and Waterflow) Fire Alarm Systems (requires TM-4).
• NFPA 72 Remote Station (Automatic, Manual and Waterflow) Fire Alarm Systems
• NFPA 72 Proprietary (Automatic, Manual and Waterflow) Fire Alarm Systems (Protected Premises Unit).
• NFPA 92 Standard for Smoke-Control Systems
• NFPA 2001 Clean Agent Fire Extinguishing Systems
• NFPA 2010 Standard for Fixed Aerosol Fire Extinguishing Systems
 The installer should be familiar with the following documents and standards:
• NFPA 72 Initiating Devices for Fire Alarm Systems
• NFPA 72 Inspection, Testing and Maintenance for Fire Alarm Systems
• NFPA 72 Notification Appliances for Fire Alarm Systems
Underwriters Laboratories
• UL 38 Manually Actuated Signaling Boxes
• UL 217 Smoke Detectors, Single and Multiple Station
• UL 228 Door Closers - Holders for Fire Protective Signaling Systems
• UL 268 Smoke Detectors for Fire Protective Signaling Systems
• UL 268A Smoke Detectors for Duct Applications
• UL 346 Waterflow Indicators for Fire Protective Signaling Systems
• UL 464 Audible Signaling Appliances
• UL 521 Heat Detectors for Fire Protective Signaling Systems
• UL 864 Standard for Control Units for Fire Protective Signaling Systems, 10th edition
• UL 1481 Power Supplies for Fire Protective Signaling Systems
• UL 1971 Visual Signaling Appliances
• UL 1076 Proprietary Burglar Alarm Systems
• UL 2017 Standard for General-Purpose Signaling Devices and Systems
• UL 2572 Standard for Mass Notification Systems
• UL 60950 Safety of Information Technology Equipment
Underwriters Laboratories of Canada (ULC)
• Standard CAN/ULC-S527-M99
• CAN/ULC-S524-M91 Standard for the Installation of Fire Alarm Systems
• ULC S524 Standard for the Installation of Fire Alarm Systems
• ULC-S527-11 Standard for Control Units for Fire Alarm Systems
• ULC S561 Installation and Services for Fire Signal Receiving Centres and Systems
Other
• EIA-485 and EIA-232 Serial Interface Standards
• NEC Article 300 Wiring Methods
• NEC Article 760 Fire Protective Signaling Systems
• Applicable Local and State Building Codes
• Requirements of the Local Authority Having Jurisdiction
1.1.1 UL 864 9th and 10th Edition

Per the UL Continuing Certification Program, UL 864 9th edition fire alarm control equipment will retain certification after the rollout of
UL 10th edition (12/2/2018).
Installations of UL 864 10th Edition certified equipment are permitted to use UL864 9th Edition certified equipment when approved by
the local Authority Having Jurisdiction (AHJ).

About This Manual Related Documents
For product compliance, refer to the UL/ULC listing cards located on the UL online certification directory. UL Product iQ:
https://iq.ulprospector.com/en/
1.2 Related Documents

Table 1.1 below provides a list of documents referenced in this manual, as well as documents for selected other compatible devices. The
document series chart (DOC-NOT) provides the current document revision. A copy of this document is included in every shipment.
Compatible Conventional Devices (Non-addressable) Document Number
Device Compatibility Document 15378
Fire Alarm Control Panel (FACP) and Main Power Supply Installation Document Number
NFS2-640/E Installation, Operations, and Programming Manuals 52741, 52742, 52743
DVC Digital Voice Command Manual 52411
DVC-RPU Manual 50107425-001
DVC-RPU UL Listing Document 50107424-001
DAL Devices Reference Document 52410
DS-DB Digital Series Distribution Board and Amplifier Manual 53622
DAA2 and DAX Amplifiers Manual 53265
SLC Wiring Manual 51253
Note: For individual SLC Devices, refer to the SLC Wiring Manual
Off-line Programming Utility Document Number
VeriFire® Tools CD help file VERIFIRE-TCD
Cabinets & Chassis Document Number
CAB-3/CAB-4 Series Cabinet Installation Document 15330
Heat Dissipation for Cabinets with Audio Products* 53645
Battery/Peripherals Enclosure Installation Document 50295
Power Supplies, Auxiliary Power Supplies & Battery Chargers Document Number
ACPS-2406 Installation Manual 51304
ACPS-610 Installation Manual 53018
APS-6R Instruction Manual 50702
APS2-6R Instruction Manual 53232
CHG-120 Battery Charger Manual 50641
FCPS-24 Field Charger/Power Supply Manual 50059
FCPS-24S6/FCPS-24S8 Field Charger/Power Supply Manual 51977
Networking Document Number
High-Speed NCM Installation Document 54014
Noti•Fire•Net Manual, Network Version 5.0 & Higher 51584
NCM-W/F Installation Document 51533
HS-NFN Installation Document 54013
ONYXWorks™ Workstation Hardware & Software Application: Installation and Operation Manual 52342
ONYXWorks™ NFN Gateway (PC Platform) Installation & Operation Manual 52307
ONYXWorks™ NFN Gateway (Embedded Platform) Installation & Operation Manual 52306
NCS ONYX® Network Control Station Manual, Network Version 4.0 & Higher 51658
NCA-2 Network Control Annunciator Manual 52482
NCA Network Control Annunciator Manual 51482
NCD Network Control Display LS10210-051NF-E
System Components Document Number
Annunciator Control System Manual 15842
FDU-80Remote Annunciator Manual 51264
LCD-80 Liquid Crystal Display Remote Annunciator 15037
Table 1.1 Reference Documentation (1 of 2)

Cautions and Warnings About This Manual
LCD2-80 Liquid Crystal Display Remote Annunciator 53242
LDM Series Lamp Driver Annunciator Manual 15885
SCS Smoke Control Manual (Smoke and HVAC Control Station) 15712
DPI-232 Direct Panel Interface Manual 51499
TM-4 Installation Document (Reverse Polarity Transmitter) 51490
UDACT Manual (Universal Digital Alarm Communicator/Transmitter) 50050
UDACT-2 Manual (Universal Digital Alarm Communicator/Transmitter) 54089
UDACT-2 Listing Document (Universal Digital Alarm Communicator/Transmitter) 54089LD
AA-Series Audio Amplifiers Manual 52526
ACT-1 Installation Document 52527
ACT-2 Installation Document 51118
FireVoice-25/50, FireVoice-25/50ZS & FireVoice-25/50ZST Manual 52290
FirstCommand Emergency Communication System LS1001-001NF-E
RM-1 Series Remote Microphone Installation Document 51138
RA100Z Remote LED Annunciator Installation Document I56-0508
XP Transponder Manual 15888
XP10-M Installation Document I56-1803
XP5 Series Manual 50786
XP6-C Installation Document I56-1805
XP6-MA Installation Document I56-1806
XP6-R Installation Document I56-1804
FSA-5000(A) FAAST XS Intelligent Aspiration Sensing Technology Document I56-6008
FSA-8000(A) FAAST XM Intelligent Aspiration Sensing Technology Document I56-3903
FSA-20000(A) FAAST XT PRO Intelligent Aspiration Sensing Technology Document I56-3903
FWSG Wireless Manual LS10036-000NF-E
Manual Releasing Disconnect (MRD-1) Product Installation Document LS10231-000GE-E
Table 1.1 Reference Documentation (2 of 2)

* If you are installing the panel in the same cabinet as digital audio equipment, heat dissipation calculations must be made. Please refer to
document #53645.
1.3 Cautions and Warnings

This manual contains cautions and warnings to alert the reader as follows:
CAUTION:
! Information about procedures that could cause programming errors, runtime errors, or equipment damage.
WARNING:
! Indicates information about procedures that could cause irreversible damage to the control panel, irreversible loss of
programming data or personal injury.

Section 2: System Overview
2.1 System Description
The NFS2-640/E control panel is a modular, intelligent fire alarm control panel (FACP) with an extensive list of powerful features. The
control panel uses the CPS-24/E integral power supply with battery charger. This is combined with a mounting chassis and cabinet to
create a complete fire alarm control system. The panel supports FlashScan® protocol and has network capabilities. A single SLC loop is
supported with the basic equipment package; a second SLC loop can be added by attaching an optional loop expander module (LEM-
320).
Modular devices mount to the chassis to provide additional output circuits, including voice and telephone modules to form a complete
voice evacuation system. Five cabinet options are available for enclosing system components; each is available in red or black.
The control panel has the capacity for installing up to 636 addressable points; 159 detectors and 159 monitor/control modules per SLC
(Signaling Line Circuit).
2.1.1 Standard Features

• Uses Notifier’s VIEW® early warning fire detection and the FlashScan or Classic Loop Interface Protocol (CLIP) families of
detectors and modules
• Integral power supply with battery charger
• Four standard Notification Appliance Circuits (NAC), Class A or B
• Alarm, Trouble, Supervisory and Security relays
• Support for 32 annunciator addresses, with 10 special annunciator groups
• Supports Style 4,Class A, Class B, and Class XSLC loops
• Connections to easily mount an expander board to add a second SLC loop
• Releasing service using on-board NACs or FCM-1 modules
• Logic Equations
• Display scroll selection
• Alarm verification supervisory indication (NYC)
• Supervisory duct detectors
• Supports Advanced Warning Addressable Combustion Sensing (AWACS) algorithms
• Network operation
• Battery charger supports 18 to 200 amp hour sealed lead-acid batteries
• EIA-485 connections for wiring ACS annunciators (including LDM custom graphic annunciators), TM-4 transmitter
• EIA-232 connections for printer, CRT, printer/CRT, or network operation
• Autoprogram feature for faster programming of new devices
• The control panel provides 6 amps of usable output power in an alarm condition; it provides 3 amps of usable output power in
normal or continuous operating conditions
• Diagnostic LEDs and switches
• Ground fault detection (0 ohm impedance)
• Battery and battery-charger supervision, voltage-monitoring, and current-monitoring
• Disconnect of deeply-discharged battery (low battery disconnect)
• Programmable for strobe synchronization
• Mass Notification System compatible
2.1.2 Options
Refer to Section 2.4 “Compatible Equipment” for other peripherals listed for use with this panel.
• QWERTY silicone-rubber keypad with a 2x40 LCD display and eight indicator LEDs
• Optional LEM-320 provides a second SLC loop that is electrically identical to the one on the main board
• Optional devices include: UDACT/UDACT-2 Universal Digital Alarm Communicator/Transmitter, ACM-8R remote relay module
to increase point capacity, and audio and voice components.
• Optional annunciators connected through the EIA-485 interface allow remote system monitoring.
2.1.3 System Limitations
System expansion must take into consideration the following:
1. The physical limitations of the cabinet configuration.
2. The electrical limitations of the system power supply.
3. The capacity of the secondary power source (standby batteries). (Note that batteries larger than 26 AH will require a separate
battery backbox.)

System Components System Overview
2.2 System Components

2.2.1 Basic Equipment
A basic NFS2-640/E system has the following components:
1. The control panel with integral power supply. CPU2-640 (120V operation) or CPU2-640E (240V operation) is the “control panel”
itself and the heart of the system; it ships with a grounding cable, battery interconnect cables, and document kit. It includes power
supply CPS-24/E, mounted directly on the CPU2-640/E.
NOTE: The CPS-24/E is an integral part of the CPU2-640/E and is not available separately.
2. One or more chassis. The NFS2-640/E chassis (included with the CPU) mounts the CPU2-640/CPU2-640E and peripherals. Mount
additional rows of equipment in a compatible chassis selected from Table 3.3 on page 25.
3. Optional: A primary display. Generally this is a KDM-R2 keypad/display behind a DP-DISP2 or ADP2-640 dress panel. For
information on using NCA-2 as primary display instead of KDM-R2, see Section 3.5.2 “Using XLS-NCA2 as Primary Display”
and the NCA-2 Manual.
4. A backbox and door:
SBB-A4 and DR-A4 (one row of equipment) or
SBB-B4 and DR-B4 (two rows of equipment) or
SBB-C4 and DR-C4 (three rows of equipment) or
SBB-D4 and DR-D4 (four rows of equipment)
(For a solid-metal door add “B” to the part number; for a red door add “R”.)
5. A battery dress panel BP2-4 is required.
6. Batteries (Refer to Appendix A.3 “Calculating the Battery Requirements” for system current-draw calculations; CAB-4 series
backboxes holds batteries up to 26 AH maximum.)
Refer to Section 2.4, “Compatible Equipment” for other peripherals listed for use with this FACP.
2.2.2 Control Panel Circuit Board

The control panel electronics are contained on one printed circuit board that incorporates a signaling line circuit (SLC) and the central
processing unit (CPU). The built-in power supply includes an integral battery charger. A keypad/display unit can be installed over the
power supply; see Figure 2.1. Wiring connections and system components are detailed in Figures 2.2 and 2.3.
Displayed Behind
DP-DISP2
DP-DISP2.wmf
Mounted in NFS2-
640/E Chassis
(with no
peripherals)
CPU2-640-
Figure 2.1 NFS2-640/E Control Panel with Optional Keypad/Display Unit Installed
2.2.3 Main Power Supply (CPS-24/E)

The main power supply is an integral part of the NFS2-640/E and mounts directly over the control panel’s circuit board. It provides a
total of 3 A (6 A in alarm) and contains an integral battery charger. This can be used for many functions including:

System Overview System Components
• Powering the NFS2-640/E

• Powering a variety of UL-listed 24 VDC notification appliances from four built-in NAC outputs
• Providing up to 1.25 A of resettable power for four-wire smoke detectors
• Providing up to 1.25 A of non-resettable power for external devices such as the TM-4 Transmitter Module.
• Providing auxiliary 24 VDC power @ 0.5A and 5 VDC power @ 0.15A.
• Fuse: 8 amps, 250 V, 5 x 20 mm, Fast-Acting, ceramic, p/n 12117.
When AC Power is lost, the deeply-discharged battery cutoff protection will be invoked at 17 volts. The power supply will be discon-
nected from the batteries. The power supply’s normal operation will be restored when AC power returns.
See Figure 2.2, “CPU2-640/CPU2-640E and Power-Supply: Wiring Connections” and Figure 2.3, “CPU2-640/CPU2-640E and Power-
Supply: Jumpers, LEDs and Switches” for details.

TB10 - DC Power
(24 VDC power-limited)
Resettable TB11 - EIA-485 ACS Mode Connection (supervised)
System Components
Non-resettable
(See Figure 3.16 on page 36) TB12 - EIA-232 Printer Connection (Figures 3.25 & 3.26)
TB12 - EIA-232 PC/Terminal Connection (CRT)
(Figure 3.27)
J1 - Network/Service Connection (NUP)
(power-limited, supervised)
J2 - USB A VeriFire Tools Connection

J3 - USB B VeriFire Tools Connection
TB13 - SLC Loop
NFS2-640 Installation — P/N 52741:P9 5/13/19

All NAC Circuits: power- #1 (supervised,
2.2.4 Circuit Board Components
limited, supervised power-limited)

(Figure 3.21 on page 39) (Figure 3.29)
TB9 - NAC#1
TB3 - Battery Connection

TB8 - NAC#2
(over-current protected, non-power-limited)
TB7 - NAC#3
TB2 - Secondary Power Auxiliary Outputs
(power-limited)
TB6 - NAC#4
for larger images and more details. (Larger images are referenced on these drawings.)
Hot TB1 - AC Power Connection (non-

power-limited)
Neutral
Earth Ground J4 - LEM-320 Connector

for (SLC Loop #2)
TB5 -
Supervisory Relay
Security Relay
Figure 2.2 CPU2-640/CPU2-640E and Power-Supply: Wiring Connections

TB4 -
CPU2640-KAPS-
Alarm Relay
Trouble Relay
Output Relays - power-limited only if connected to a power-
limited source. (See Section 3.9 for details.) J7 - KDM-R2
Connection J5 - Security Tamper Switch
J6 - Auxiliary Trouble Input
and its power supply. Figure 2.2 shows wiring connections; Figure 2.3 shows jumpers, LEDs and switches. See Section 3 “Installation”
The following two figures illustrate the location of the various connections, switches, jumpers and LEDs on the CPU2-640/CPU2-640E
13
System Overview
14
JP1 - Ground Fault
Jumper (SLC#1)
System Overview
NAC
LEDs
LED5 - +24V Aux LED
LED6 - +5V Aux LED

LED1 - Logic Power LED
LED2 - Trouble LED

LED3 - Earth Fault LED (general board ground fault)
SW1 - Ground Fault Detection Enable/Disable
LED4 - AC Power LED

LED10 – SLC Loop 1
Ground Fault LED
F4 - AC Fuse LED9 – SLC Loop 2
Ground Fault LED
CPU2640-KAPS-2.wmf, CPU2-640-LEDs.wmf
Disable - Enable Switches for System Switches for No-

Backup Alarm (Figure 3.10) Keyboard Operation
SW5 - Acknowledge
SW6 - Silence
SW7 - Reset
LED1 - Power-on LED (AC or battery)

LED2 - Signals Silenced LED
Figure 2.3 CPU2-640/CPU2-640E and Power-Supply: Jumpers, LEDs and Switches

LED3 - Point Disabled LED
LED4 - System Trouble LED
LED5 - Supervisory LED
LED6 - Security LED
LED7 - Pre-Alarm LED
LED8 - Fire Alarm LED
NFS2-640 Installation — P/N 52741:P9 5/13/19

System Components
System Cabinets System Overview
2.3 System Cabinets

The control panel and modules are installed in a CAB-4 series backbox . There are four different sizes available, holding from one to
four rows of equipment plus batteries (up to two 26 AH batteries). Backboxes are ordered separately from doors. The doors can be
mounted on the left or the right side of the cabinet; reversible hinges are provided so that this choice can be made in the field. Doors open
a full 180 degrees and have locks. Mounting methods include surface-mounting or semi-flush mounting on a wall between 16 inch
(40.64 cm) on-center studs. A trim ring option is available for semi-flush mounting.
External measurements for each backbox are provided below; door dimensions are larger. Refer to CAB-3/CAB-4 Series Cabinet Instal-
lation Document (shipped with the cabinet) for specific mounting drawings and door dimensions.
A-size backbox (one 24.00 in (60.96 cm) wide Optional trim ring TR-A4
row) 20.00 in (50.8 cm) tall Opening: 24.062 in (61.118 cm) wide;
5.218 in (13.254 cm) deep 20.062 in (50.881 cm) tall.
Uses optional trim ring TR-A4 Molding width: 1.375 in (3.493 cm)
B-size backbox (two 24.00 in (60.96 cm) wide Optional trim ring TR-B4
rows) 28.5 in (72.39 cm) tall Opening: 24.062 in (61.118 cm) wide;
Uses optional trim ring TR-B4 Molding width: 1.375 in (3.493 cm)
C-size backbox 24.00 in (60.96 cm) wide Optional trim ring TR-C4
(three rows) 37.125 in (94.297 cm) tall Opening: 24.062 in (61.118 cm) wide;
Uses optional trim ring TR-C4 Molding width: 1.375 in (3.493 cm)
D-size backbox (four 24.00 in (60.96 cm) wide Optional trim ring TR-D4
rows) 45.75 in (1162.05 cm) tall Opening: 24.062 in (61.118 cm) wide;
Uses optional trim ring TR-D4 Molding width: 1.375 in (3.493 cm)
Trim Rings: When using trim rings, mount backbox with at least 1 inch (2.54 cm) between wall surface and front of backbox, to
allow door to open fully past the trim ring.
For details on mounting options within the cabinet, see Section 3.4, “Laying Out Equipment in Cabinet and Chassis”.
2.4 Compatible Equipment

These are the most common devices at time of publishing; the most complete list of compatible intelligent SLC loop devices is provided
in the SLC Wiring Manual; for conventional non-addressable equipment see the Device Compatibility Document. These devices are UL
and ULC listed unless marked otherwise (in parentheses next to the product). Other control panels and their equipment can also be con-
nected in a network, via Noti•Fire•Net version 5.0 or the High-Speed Noti•Fire•Net; refer to the Noti•Fire•Net Version 5.0 & Higher
Installation Manual or the High-Speed Noti•Fire•Net Installation Manual for details. For products documented separately, see
Section 1.3 “Related Documents”.
WARNING: UL 9TH COMPLIANCE

! THIS PRODUCT HAS BEEN CERTIFIED TO COMPLY WITH THE REQUIREMENTS IN THE STANDARD FOR CONTROL
UNITS AND ACCESSORIES FOR FIRE ALARM SYSTEMS, UL 864 9TH EDITION. OPERATION OF THE NFS2-640/E
WITH PRODUCTS NOT TESTED FOR UL 864 9TH EDITION HAS NOT BEEN EVALUATED AND MAY NOT COMPLY
WITH NFPA 72 AND/OR THE LATEST EDITION OF UL 864. THESE APPLICATIONS WILL REQUIRE THE APPROVAL
OF THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ).
PERIPHERAL DEVICES IN THE SECOND LIST WERE LISTED UNDER UL 8TH EDITION AND MAY ONLY BE USED IN
RETROFIT APPLICATIONS (SEE SECTION 1.2, “UL 864 COMPLIANCE”, ON PAGE 8).
Notifier® Compatible Equipment

• “A” or “CDN” suffix indicates a ULC Listed model.
• “IV” suffix indicates ivory color and is a FlashScan and CLIP device
• Products marked with a check mark have not received UL 864 9th Edition certification and may only be used in retrofit
applications.
• The wireless option is not suitable for ULC.
Electronic Equipment
AA-100 100-Watt Audio Amplifier AcclimatePlus FAPT-851 Combination Photoelectric/Heat Detector
AA-120 120-Watt Audio Amplifier AEM-24AT Annunciator Expander Module
AA-30 30-Watt Audio Amplifier AEM-48A Annunciator Expander Module
ACM-24AT Annunciator Control Module AKS-1B Annunciator Key Switch
ACM-48A Annunciator Control Module APJ-1B Annunciator Phone Jack-G
ACM-8R Annunciator Control Module APS2-6R Auxiliary Power Supply (for UL applications only)
ACPS-610 Addressable Charger/Power Supply A77-716B End-of-Line Resistor Assembly
ACPS2-6R Auxiliary Power Supply B200S Intelligent Programmable Sounder Base
ACT-1 Audio Coupling Transformer B200S-IV Intelligent Programmable Sounder Base Ivory
ACT-2 Audio Coupling Transformer B200S-WH Intelligent Programmable Sounder Base White
AcclimatePlus FAPT-751 Combination Photoelectric/Heat Detector B200S-LF Low-Frequency Intelligent Programmable Sounder Base

System Overview Compatible Equipment
B200S-LF-IV Low-Frequency Intelligent Programmable Sounder Base Ivory FCO-851 Fire/CO Detector
B200S-LF-WH Low-Frequency Intelligent Programmable Sounder Base White FCO-951(A) Carbon Monoxide Sensors
B200SA Intelligent Sounder Base FCO-951(A)-IV Carbon Monoxide Sensors Ivory
B200SA-IV Intelligent Sounder Base Ivory FCPS-24S6/S8 Field Charger/Power Supply
B200SA-WH Intelligent Sounder Base White FDM-1 Dual Monitor Module
B200SCOA Intelligent Programmable Sounder Base FDRM-1 Dual Monitor/Dual Relay
B200SCOA-IV Intelligent Programmable Sounder Base Ivory FDX-551 Intelligent Thermal Sensor
B200SCOA-WH Intelligent Programmable Sounder Base White FDX-551R Intelligent Thermal Rate-of-Rise Sensor
B200SR Intelligent Sounder Base FHS Fireman's Handset
B200SR-IV Intelligent Sounder Base Ivory FMM-1 Monitor Module
B200SR-WH Intelligent Sounder Base White FMM-101 Mini Monitor Module
B200SR-LF Low-Frequency Intelligent Sounder Base FMM-4-20 Monitor Module
B200SR-LF-IV Low-Frequency Intelligent Sounder Base Ivory FPC-951(A) Multi Criteria PHOTO/CO Detector
B200SR-LF-WH Low-Frequency Intelligent Sounder Base White FPJ Fireman's Phone Jack
B200SRA Intelligent Sounder Base FPTI-951(A) Multi-Criteria Photoelectric, Thermal and Infrared Sensor
B200SRA-IV Intelligent Sounder Base Ivory FPTI-951(A)-IV Multi-Criteria Photoelectric, Thermal and Infrared Sensor Ivory
B200SRA-WH Intelligent Sounder Base White FRM-1 Relay Module
B210LP Flange Mounted Base FSA-5000/A (FAAST XS) Intelligent Aspiration detector
B210LPA ULC Flange Mounted Base FSA-8000/A (FAAST XM) Intelligent Aspiration detector
B210LPBP Bulk Pack of B300-6. Package of 10 FSA-20000/A (FAAST XT) Intelligent Aspiration detector
B224BI Isolator Bases for Low-profile Detectors FSA-20000P (FAAST XT PRO) Intelligent Aspiration detector
B224BI-IV Isolator Bases for Low-profile detectors Ivory FSA-851A Intelligent Aspiration Detector - 06-NF10 Baffle for the FSA-851A
B224BI-WH Isolator Bases for Low-profile detectors White FSB-200S Single Ended Beam Smoke Detector With Sensitivity Testing
B224BIA Isolator Base for Low-profile detectors FSB-200 Single Ended Beam Smoke Detector
B224BIA-IV Isolator Base for Low-profile detectors Ivory FSC-851 IntelliQuad Multi-Criteria Smoke Detector
B224BIA-WH Isolator Base for Low-profile detectors White FSCO-951(A) Carbon Monoxide Sensor
B224RB Low-profile Relay Base FSD-751P/RP/PL Duct Detectors
B224RB-IV Low-profile Relay base Ivory FSH-751 HARSH™ Photo Detector
B224RB-WH Low-profile Relay base White FSI-751 Ion Detector
B224RBA Low-profile Relay base FSI-851 Ion Detector
B244RBA-IV Low-profile Relay base Ivory FSL-751 FlashScan VIEW® Laser Detector
B244RBA-WH Low-profile Relay base White FSM-101 Pull Station Monitor Module
B300-6 Intelligent Detector Base 6 Inch White FS-OSI-RI(A) Intelligent Single Ended Reflected Type Projected Imaging Beam
B300-6-IV Intelligent Detector Base 6 Inch Ivory Smoke Detector
B300A-6 Intelligent Detector Base 6 Inch White Canada FSP-751 Photo Detector
B300A-6-IV Intelligent Base 6 Inch Ivory Canada FSP-751T Photo/Thermal Detector
BX-501 Intelligent Detectors/Sensors Base FSP-851 Photo Detector, listed for use in ducts
B501 USA Intelligent Detector Base FSP-851T Photo/heat Detector, listed for use in ducts
B501A ULC Intelligent Detector Base FST-751 Thermal Detector
B501BH-2 Sounder Base FST-751R Thermal Rate-of-rise Detector
B501BHT-2 Temporal Sounder Base FST-851 Thermal Detector
B501-White Intelligent Detector Base White FST-851H High-temperature Thermal Detector
B501-BL Intelligent Detector Base Black FST-851R Thermal Rate-of-rise Detector
B501-IV Intelligent Detector Base Ivory FSP-951 Photo Detector
B710HD HARSH Detector Base FSP-951-IV Photo Detector/Dual Protocol Ivory
B710LP European Intelligent Detector Base FSP-951R Photo RAT
BAT-12120 Battery 12-volt, 12 amp-hour FSP-951R-IV Photo RAT/Dual Protocol Ivory
BAT-12180 Battery 12-volt, 18 amp-hour FSP-951P Photo/Thermal
BAT-12250 Battery 12-volt, 25 amp-hour FSP-951T-IV Photo/Thermal/Dual Protocol Ivory
BAT-12260 Battery 12-volt, 26 amp-hour FST-951 Programmable Heat
BAT-12550 Battery 12-volt, 55 amp-hour FST-951-IV Programmable Heat/Dual Protocol Ivory
BAT-12600 Battery 12-volt, 60 amp-hour
BDA-25V/75V Backup Amplifier FST-951R Heat Detector Rate of Rise
CK300 Color Kit White FST-951R-IV Heat Detector Rate of Rise/Dual Protocol Ivory
CK300-IR Color Kit White with IR Opening FST-951H Heat Detector High
CK300-IV Color Kit Ivory FST-951H-IV Heat Detector High/Dual Protocol Ivory
CK300-IR-IV Color Kit Ivory with IR Opening FSV-951(A) Intelligent High Sensitivity Photoelectric Smoke Detector
CK300-BL Color Kit Black FSV-951(A)-IV Intelligent High Sensitivity Photoelectric Smoke Detector Ivory
CK300-IR-BL Color Kit Black with IR Opening FSV-951RA Intelligent High Sensitivity Photoelectric Smoke Detector Retrofit
CMM-1 Communication converter Module FSV-951RA-IV Intelligent High Sensitivity Photoelectric Smoke Detector Retrofit
Ivory
CMX-1 Addressable Control Module
FTM-1 Telephone Module
CMX-2 Addressable Control Module
FW-MM Wireless Monitor Module
CPU2-640/E Control Panel Circuit Board
FW-RM Wireless Relay
CPX-551 Intelligent Ionization Smoke Detector
FWD-200ACCLIMATE Wireless Acclimate detector
CPX-751 Intelligent Ionization Smoke Detector
FWD-200P Wireless photo detector
CRT-2 Video Display Monitor With Keyboard
FWH-200FIX135 Wireless, fixed-temperature heat detector
DAA Series Digital Audio Amplifiers
FWH-200ROR135 Wireless, rate-of-rise heat detector
DAA2 Series Digital Audio Amplifier
FWSG Wireless Gateway
DAX Digital Audio Amplifier
FZM-1 Zone Module
DHX-501 Duct Detector
HPX-751 HARSH™ Hostile Environment Smoke Detector
DHX-502 Duct Detector
HS-NCM-MF High-Speed Network Communications Module (Multi-Mode Fiber)
DNR/W/A Intelligent Non-Relay Photoelectric Duct Detector
HS-NCM-MFSF High-Speed Network Communications Module (Multi-Mode
DPI-232 Direct Panel Interface Fiber to Single-Mode Fiber)
DS-AMP Audio Amplifier HS-NCM-SF High-Speed Network Communications Module (Single-Mode Fiber)
DS-BDA Backup Audio Amplifier HS-NCM-W High-Speed Network Communications Module (Wire)
DS-DB Digital Distribution Board HS-NCM-WMF High-Speed Network Communications Module (Wire to Multi-
DS-XF70V Transformer Mode Fiber)
DVC-AO Digital Voice Command Audio Output HS-NCM-WSF High-Speed Network Communications Module (Wire to Single-
DVC-EM Digital Voice Command Mode Fiber)
DVC-RPU DVC Remote Paging Unit HWF2A-COM IP Digital Alarm Communicator
FCM-1 NAC Module HWF2A-COM IP Digital Alarm Communicator
FCM-1-REL Control Module

Compatible Equipment System Overview
ISO-X Loop Fault Isolator Module RA100Z Remote Annunciator with diode
ISO-6/A Six Fault Isolator Module RA400 Remote Annunciator
LCD-80 Liquid Crystal Display Module RPJ-1 Remote Phone Jack
LCD2-80 Liquid Crystal Display Module RPT-485SF EIA-485 Repeater (Fiber)
LDM-E32 Lamp Driver Module Ivory RPT-485W EIA-485 Repeater (Wire)
LDM-R32 Lamp Driver Module RPT-485WF EIA-485 Repeater (Wire/Fiber)
LDM-32 Lamp Driver Module RM-1 Remote Microphone
LEM-320 Loop Expander Module RM-1SA Remote Microphone
LDM-E32 Lamp Driver Module Ivory SCS-8, SCE-8 Smoke Control System
LDM-R32 Lamp Driver Module SDX-551 Intelligent Photoelectric Detector
LDM-32 Lamp Driver Module SDX-551TH Intelligent Photoelectric and Thermal Detector
LEM-320/A Loop Expander Module SDX-751 Intelligent Photoelectric Detector
MMX-1 Addressable Monitor Module SLC-IM Signaling Line Circuit Integration Module (FlashScan)
MMX-2 Addressable Monitor Module STS-1 Security Tamper Switch (Not ULC-listed)
MMX-101 Addressable Mini Monitor Module TM-4 Transmitter Module
MRD-1 Manual Releasing Disconnect Assembly TR300 Trim Ring White
N-ELR Assortment ELR Pack with Mounting Plate TR300-IV Trim Ring Ivory
NBG-12 Series Addressable Manual Pull Station UDACT/UDACT-2 Universal Digital Alarm Communicator Transmitter
NBG-12LRA - Agent Release Abort Station UZC-256 Universal Zone Coder
NBG-12LX Addressable Manual Pull Stations VEP-A00-P-NTF Addressable VESDA-E VEP with LEDs
NBG-12LXP Portuguese Labeled Addressable Pull Station VEP-A10-P-NTF Addressable VESDA-E VEP with 3.5"Display
NBG12LXSP Spanish Labeled Addressable Pull Station VEP-A00-1P-NTF Addressable VESDA-E VEP 1 Pipe with LEDs
NCA-2/C Network Communications Annunciator VEU-A00-NTF Addressable VESDA-E VEU with LEDs
NCD Network Control Display VEU-A10-NTF Addressable VESDA-E VEU with 3.5" Display
NCM-F Network Communications Module (Fiber) VEA-040-A00-NTF Addressable VESDA-E VEA-40 point with LEDs
NCM-W Network Communications Module (Wire) VEA-040-A10-NTF Addressable VESDA-E VEA-40 point with 3.5" Display
NCO-200 Carbon Monoxide Sensor XPIQ Quad Intelligent Audio Transponder (Audio Applications)
NCS Network Control Station XP10-M Ten Input Monitor Module
N-MPS MPS Series Pull Station XP6-C Supervised Control Module
NFV Notifier FireVoice 25/50 XP6-MA Six Zone Interface Module
NP-200C PHOTO/CO Detector XP6-R Six Relay Control Module
ONYXWorks® Workstation Network Monitoring Workstation
PRN-6 80-Column Printer System Sensor Devices
PRN-7 80-Column Printer A2143-00 End of Line Resistor Assembly
R-120 120 Ohm End-of-Line Resistor EOLR-1 End of Line Resistor Assembly
R-2.2K 2.2K End-of-Line Resistor
R-27K 27K End-of-Line Resistor
R-470 470 End-of-Line Resistor
R-47K 47K End-of-Line Resistor
Backboxes, Chassis, Dress Panels, etc.

BF-1B/C Annunciator Flush Box ABS-1TB/C Annunciator Surface Box
ABF-1DB/C Annunciator Flush Box with Door ABS-2B Annunciator Surface Box
ABF-2B Annunciator Flush Box ABS-2D/C Annunciator Surface Box
ABF-2DB/C Annunciator Flush Box with Door ABS-4D/C Annunciator Surface Box
ABF-4B Annunciator Flush Box ABS-8RB Annunciator Backbox for ACM-8R
ABM-16AT Annunciator Blank Module ADP2-640 Dress Panel: NFS2-640/E in lower row
ABM-32A Annunciator Module Blank ADP-4B Annunciator Dress Panel
ABS-1TB Annunciator Surface Box BMP-1 Blank Module Plate
ABS-1B/C Annunciator Surface Box BP2-4 Battery Dress Plate
Retrofit Equipment: Compatible NotifierEquipment Listed Under Previous Editions of UL 864

NOTE: The products in this list have not received UL 864 9th Edition certification and may only be used in retrofit applications.
ACM-16AT Annunciator Control Module MMX-1 Addressable Monitor Module

ACM-32A Annunciator Control Module NCA Network Communications Annunciator
ACPS-2406 Auxiliary Charger/Power Supply PRN-4, PRN-5 80-Column Printers
AEM-16AT Annunciator Expander Module RFX Wireless Transmitter (version 2.0 and higher)
AEM-32A Annunciator Expander Module SDRF-751 Wireless Photo/Thermal Smoke Detector (Not ULC-listed)
AFM-16A Annunciator Fixed Module VS4095 Keltron Printer (Dress plate P-40) (Not ULC-listed)
AFM-32A Annunciator Fixed Module XPIQ Quad Intelligent Audio Transponder (NAC Applications)
AMG-1/E Audio Message Generator XP5-C Transponder Control Module
APS-6R Auxiliary Power Supply XP5-M Transponder Monitor Module
B501BH/B501BHT Sounder Base XPC-8 Transponder Control Module
BGX-101L Addressable Manual Pull Station XPM-8 Transponder Monitor Module
CHG-120 Battery Charger XPM-8L Transponder Monitor Module
FCPS-24 Field Charger/Power Supply XPP-1 Transponder Processor
IPX-751 Advanced Multi-Sensor Intelligent Detector XPR-8 Transponder Relay Module
Table 2.1 Notifier Compatible Equipment Chart 3 of 3

Refer to document 15378, Device Compatibility Document, and document 51253, SLC Signaling Line Circuit Manual, for a list of other
devices compatible with this FACP.
NOTE: The FWSG Wireless Gateway as part of the wireless network has been tested for compliance with the Federal Communications
Commission (FCC) requirements of the United States Government. This product has not been evaluated for use outside the USA. Use of
this system outside the USA is subject to local laws and rules to which this product may not conform. It is the sole responsibility of the user
to determine if this product may be legally used outside the USA.

Section 3: Installation
3.1 Preparing for Installation
Choose a location for the fire alarm system that is clean, dry, and vibration-free with moderate temperature. The area should be readily
accessible with sufficient room to easily install and maintain it. There should be sufficient space for cabinet door(s) to open completely.
Carefully unpack the system and inspect for shipping damage. Count the number of conductors needed for all devices and find the appro-
priate knockouts. (Refer to Section 3.11 “UL Power-limited Wiring Requirements” for selection guidelines.)
Before installing the fire alarm system, read the following:
• Review the installation precautions at the front of this manual, including temperature and humidity limits for the system (Page 3).
• All wiring must comply with the National and Local codes for fire alarm systems.
• Do not draw wiring into the bottom 9 inches (22.86 cm) of the cabinet except when using a separate battery cabinet; this space is for
internal battery installation.
• Review installation instructions in Section 3.2 “Installation Checklist”.
CAUTION: Make sure to install system components in the sequence listed below. Failure to do so can damage the control
! panel and other system components.
WARNING: This system contains static-sensitive components. Always ground yourself with a proper wrist strap before
! handling any circuits. Use static-suppressive packaging to protect electronic assemblies removed from the unit.
3.1.1 Standards and Codes

In addition, installers should be familiar with the following standards and codes:
• NEC Article 300 Wiring Methods.
• NEC Article 760 Fire Protective Signaling Systems.
• Applicable Local and State Building Codes.
• Requirements of the Local Authority Having Jurisdiction.
• C22.1-98 The Canadian Electrical Code, Part 1.
• CAN/ULC-S5524-01 Standard for the Installation of Fire Alarm Systems.

Installation Checklist Installation
3.2 Installation Checklist

Table 3.1 provides an installation checklist for installing, wiring, and testing the NFS2-640/E system. It has references to installation
information included in manuals listed in Section 1.3 “Related Documents”.
Seq Task Refer to
1. Mount the cabinet backbox to the wall. Section 3.3 “Mounting a Cabinet”
2. Install hinges for door CAB-3/CAB-4 Series Cabinet Installation Document
3. Install all required chassis in cabinet. Section 3.5 “Installing the Control Panel”
4. Install control panel onto chassis. Section 3.5.1 “Control Panel Circuit Board &
Keypad/Display Unit”
5. Optional: Install auxiliary power supply and/or external Auxiliary power manuals
battery charger
6. Connect AC wiring, place batteries into backbox without Section 3.7 “Connecting the Power Cables”
connecting them, and run cable to optional power supplies,
DC power outputs, NACs, and relays.
CAUTION: Do not apply AC or DC power at this time.
7. Set switches for backup alarm (SW1-SW4). Section 3.10 “Backup-Alarm Switches”
8. Optional: Install option boards, annunciators, network Section 3.6, “Mounting Option Boards”, the relevant
equipment, and Audio components annunciator/network-card manual, DVC Manual, and DVC-
RPU Manual.
9. Optional: Install output devices such as a printer, or CRT Section 3.13 “Installing Remote Printers and/or CRT”
terminal.
10. Optional: Install NCA-2, NCD, NCS or ONYXWorks. NCA-2 Manual, NCD Manual, NCS Manual or ONYXWorks
Manual
11. Secure any unused mounting holes in control panel Figure 3.8
circuit board.
12. Wire the Signaling Line Circuits. Section 3.14 “Wiring a Signaling Line Circuit (SLC)”
13. Terminate wire shielding as instructed. SLC Wiring Manual
14. Apply AC power to the control panel by placing the external circuit breaker to the ON position.
Do NOT connect batteries.
15. Check AC power. Table 3.5 in Section 3.7 “Connecting the Power Cables”
16. Connect the batteries using interconnect cable, P/N 75560 and 75561.
17. Install the CAB-4 series door. CAB-3/CAB-4 Series
Cabinet Installation Document
18. Program the control panel. NFS2-640/E Programming Manual
19. Field test the system. Section 5 “Testing the System”
Table 3.1 Installation Checklist
3.3 Mounting a Cabinet

This section provides instructions for mounting a CAB-4 Series backbox to a wall. Follow these guidelines when mounting the backbox:
• Locate the backbox so that the top edge is 66 inches (1.6764 m) above the surface of the finished floor.
• Access to the cabinet shall be provided in accordance with NFPA 90, article 110.33.
• Allow sufficient clearance around cabinet for door to swing freely. (See Section 2.3 “System Cabinets”.)
• Use the four holes in the back surface of the backbox to provide secure mounting. (See Figure 3.1.)
• Mount the backbox on a surface that is in a clean, dry, vibration-free area.
CAUTION: Unless you are familiar with the placement of components within this backbox, only use the knockout locations
! provided for conduit entry.
Follow the instructions below.

1. Mark and pre-drill holes for the top two keyhole mounting bolts (0.25 inch, 0.635 cm). Use mounting hardware appropriate for the
mounting surfaces and weight of loaded cabinet; see UL 2017 Pull-Test Requirements.
2. Select and punch open the appropriate knock-outs. (For selection guidelines, see Section 3.11 “UL Power-limited Wiring
Requirements”.)
3. Using the keyholes, mount the backbox over the two screws.
4. Mark the location for the two lower holes, remove the backbox and drill the mounting holes.
5. Mount the backbox over the top two screws, then install the remaining fasteners. Tighten all fasteners securely.
6. Feed wires through appropriate knockouts.

Installation Laying Out Equipment in Cabinet and Chassis
7. Install control panel and other components according to Section 3.5 “Installing the Control Panel” before installing hinges and door
according to CAB-3/CAB-4 Series Cabinet Installation Document.
CAB-4
Series
CAB-4
Backbox,
Series Keyholes
nfs640cabinetmountingholes.wmf
D-size
Backbox, 2 places
(four-row)
A-size (one-
row)
Mounting holes
2 places
Figure 3.1 Mounting Holes of a Backbox
3.4 Laying Out Equipment in Cabinet and Chassis

The NFS2-640/E allows for flexible system design. Backboxes are available to hold up to four rows of equipment (four chassis), plus
batteries. Each chassis has four “slots” -- the basic positions available side by side on a chassis. The number of modules that can be
mounted in each position depends on the chassis model and the module size.
Follow these guidelines when deciding where to locate equipment in the backbox.
The NFS2-640/E control panel and adjacent first-row modules mount in the NFS2-640 chassis, typically installed in the first/top row of
the backbox behind DP-DISP2. (Use ADP2-640 if mounting NFS2-640 chassis in a lower row.) NFS2-640 chassis holds four layers of
equipment, including the control panel. See Figure 3.3. The primary display (KDM-R2, NCD or NCA-2) mounts in front of NFS2-
640/E.
The CPU mounts in the NFS2-640 chassis behind DP-DISP2 (top row) or ADP2-640 (lower row). The control panel fills three positions
in the first-installed layer against the chassis; its power supply occupies two positions on top of the control panel; and the optional dis-
play occupies two positions in the fourth layer (flush with the dress panel).
Mount second, third, or fourth rows of equipment in other compatible chassis, such as chassis CHS-4L, CA-1, or CA-2. (See Table 3.3,
“Chassis Compatibility,” on page 23.) For details on audio equipment see the DVC Manual.
Option boards use standard mounting hole positions to allow them to be mounted in various locations and layers, depending on the
desired system configuration. (See Table 3.2 to determine hardware.) Some equipment such as annunciators may be mounted on a dress
panel directly in front of the control panel. The BMP-1 Blank Module Plate covers unused positions in a dress-panel, also providing an
additional mounting location for some option boards, such as TM-4 (see BMP-1 Product Installation Drawing for details).
Annunciators can be mounted in dress panels such as ADP-4B; one or two annunciators can be installed in the DP-DISP2 or ADP2-640
with the control panel. Installing the BMP-1 blank plate in these dress panels provides an additional mounting location for option boards.
Refer to the equipment’s documentation for details.
Install BP2-4 Battery Plate in front of the battery compartment in NFS2-640/E installations and provides Protected Premises Unit labels.
NOTE: The BP2-4 is required for NFS2-640/E installations due to UL’s revised labeling requirements. If using NFS2-640/E
in retrofits, order BP2-4 to replace previous BP-4 battery dress panels.
If DP-DISP2 is not being used in the top row of the backbox, install VP-2B above the first row to cover the remaining space.

Laying Out Equipment in Cabinet and Chassis Installation
NOTE: When designing the cabinet layout, consider separation of power-limited and non-power-limited wiring as discussed in Section
3.11 “UL Power-limited Wiring Requirements.”
Slot 1 (CPU, CPS-24, and

primary display)
Slot 2 (CPU, CPS-24,

and primary display)
Slot 3 (Mounting location

for LEM-320) or other
Keypad/display option board
unit attaches to
chassis rails Slot 4 Mounting location for
option boards and other
compatible peripherals
(Recommended mounting
location for fiber versions of the
NCM and HS-NCM)
CHS2-M2iso.wmf
Also see Figure 3.3, “Top View of
NFS2-640/E Chassis Mounting
Figure 3.2 Side View of the NFS2-640/E Chassis Mounting Options
Up to two option boards Up to three option boards

(Including LEM-320 if used) (2 only if longer standoffs
Keyhole are used)
Backbox
Chassis Keyhole
CPU
CPS-24/E
DP-DISP2
(or ADP2-640
if in lower row) Left Annunciator Primary Display KDM- Right Annunciator
(mounts to dress panel) R2 or NCA-2 (mounts (mounts to dress panel)
to chassis)
CHS2-
Option boards
Mounted on BMP-1
Figure 3.3 Top View of NFS2-640/E Chassis Mounting Options
When installing the Network Control Display (NCD) into the NFS2-640 chassis, it can only be left mounted because of the position of
the grounding screw.

Installation Laying Out Equipment in Cabinet and Chassis
Backbox
CPS-24/E
NCDMounting1.w
Dress Panel
NCD
Option boards
Mounted on BMP-1
Figure 3.4 Top View of Mounting an NCD in the NFS2-640 Chassis
NCD Annunciators, which are connected to the Fire Alarm Control Panel
Figure 3.5 Top View of Mounting an NCD with Annunciators
NOTE: See the NCD Manual LS10210-051NF-E for more information.

Laying Out Equipment in Cabinet and Chassis Installation
From… To… Required Stand-off or Hardware

NFS2-640/E chassis Control panel or Attaches directly to chassis.
option board on first layer
NFS2-640/E chassis Keypad/display unit Attaches directly to chassis rails.
NFS2-640/E chassis NCA-2, NCD Attaches directly to chassis rails with mounting hardware NCA/640-2-KIT (ordered
separately)
Control panel Any option board in third slot 4 male-female stand-offs 1 inch (25.4 mm) P/N 42118; installed and shipped with
(third slot) (such as LEM-320) CPU2-640/CPU2-640E.
Option board or NFS2- Option board in next layer (not 4 male-female stand-offs either 1.5 inch (38.1 mm) P/N 42175 or 0.937 inch (23.8
640/E chassis (fourth slot) including LEM-320) mm) P/N 42166, both shipped with option boards. Choose stand-off length that
allows space for your option board’s connectors; using longer stand-offs may
reduce the number of option boards that fit in the chassis position.
Chassis or Dress Panel Annunciator Attaches directly to dress panels or attaches to flanges on chassis CHS-4/4N.
(Screws provided with annunciator.)
Dress panels Option board BMP-1 attaches to dress panel; option module attaches to BMP-1. (Screws
DP-DISP2, ADP2-640, provided with option module). See Figure 3.9.
ADP-4B
Dress panel ADP-4B NCA-2 Use “NCA-2 RETRO kit” hardware if mounting NCA-2 to a dress panel; cannot be
mounted in front of the NFS2-640/E chassis.
Table 3.2 Stand-off Lengths
Product Chassis/Door-mounting options
NFS2-640/E • NFS2-640/E chassis
NCA-2, NCD • CHS-M2, NFS2-640/E chassis, CHS-M3

• CA-2; requires two rows in the backbox
DVC • CA-1
• CA-2
DVC-RPU • CA-1
DAA • Factory-mounted in its own chassis.
Analog audio amplifiers AA-30, AA-100, AA-120 • Mounts directly onto CAB-4 backbox
Option boards • NFS2-640/E chassis, CHS-4, CHS-4L, CHS-4N (shipped as part of kit CHS-4MB), or on BMP-
1 inside dress plate
• Note: Mount LEM-320 in front of CPU2-640 in the NFS2-640/E chassis.
• Note: Mount UDACT/UDACT-2 in second or lower row, or in
slot 4 of the NFS2-640/E chassis with nothing in front of it.
• Note: Mount fiber versions of the NCM and HS-NCM in the top row under knockouts, to avoid
excessive bend on the fiber-optic cable.
ACS series annunciators ACM-24AT, ACM-48A and • Dress Panel DP-DISP2, ADP2-640, or ADP-4B
expanders
Table 3.3 Chassis Compatibility
NOTE: In retrofit applications, the CAB-e series backbox may be used, but order BP2-4 to replace previous BP-4 battery dress panels.
Typical Backbox Location(s)

Chassis/Dress plate
in CAB-4 Backboxes
NFS2-640/E chassis Top row of backbox typical; lower rows also possible.
CA-1 Second or lower row of backbox
CA-2 Requires two rows of backbox
CHS-4, CHS-4L, CHS-4N Second or lower row of backbox
DPA-2 Dress Panel Mounts in front of CA-2 covering two rows of the backbox
DP-DISP2 Dress Panel Mounts in front of the NFS2-640/E chassis in top row of backbox
ADP2-640 Dress Panel Mounts in front of NFS2-640/E chassis in second or lower row of backbox
ADP-4B Dress Panel Mounts in front of any chassis
Table 3.4 Chassis Locations in CAB-4 Backboxes

Installation Installing the Control Panel
3.5 Installing the Control Panel

3.5.1 Control Panel Circuit Board & Keypad/Display Unit
The control panel comes pre-mounted in the NFS2-640/E chassis, which is usually positioned in the top row of the backbox. The control
panel’s CPU occupies three positions at the back of the chassis; the KDM-R2 occupies three positions flush with the dress panel. The
NCA-2 may be mounted directly in front of the control panel if no KDM-R2 is being used; use NCA/640-2-KIT as described in the
NCA-2 Installation Manual.
Figure 3.6 NFS2-640/E Chassis Mounting
Perform the following steps when installing the NFS2-640/E:

1. Screw chassis to the backbox.†
2. If installing KDM-R2 as primary display:
• Attach ribbon cable from keypad to J7 connector on control panel. (See Figure 2.2.)
• Align the keypad with the mounting holes as shown in Figure 3.8 and screw it down.
3. If installing the NCA-2 as primary display: Secure it to the NFS2-640/E chassis with NCA/640-2-KIT as described in the NCA-2 Man-
ual.
4 If installing option boards, do so as described in Section 3.6, “Mounting Option Boards”. If NFS2-640/E is being installed into an
older backbox, two additional steps must be taken:
5. Battery Plate BP-4 must be replaced with BP2-4, per UL’s revised labeling requirements.
6. The older door and dress panel must be replaced with equipment compatible with KDM-R2.
†If the NFS2-640/E chassis is not assembled as when shipped, attach CPU2-640 to the chassis. Slide control-panel tabs into slots on
chassis and lay the board onto stand-offs so that mounting holes line up with those on the chassis. Secure with six screws and four 1 inch
stand-offs as shown in Figure 3.7, “Mounting KDM-R2”.
CAUTION: It is critical that all mounting holes of the NFS2-640/E are secured with a screw or standoff to insure continuity
! of Earth Ground.

Mounting Option Boards Installation
2-640_assembly_3-2.wmf
Figure 3.7 Mounting KDM-R2
3.5.2 Using NCA-2 as Primary Display

The NFS2-640/E can be set up to use the NCA-2 as the primary display. In this system design, mount NCA-2 to the NFS2-640/E chassis
in front of CPS-24/E, and connect the network/service port on the NFS2-640/E (J1) directly to the network/service port on the NCA-2
(J3). See the NCA-2 Manual for specific instructions.
NOTE: This system design is required in Canadian stand-alone applications.
If the NFS2-640/E and NCA-2 are being used as a stand-alone pair, each device must be programmed using VeriFire Tools. Connect the
VeriFire Tools PC to NFS2-640/E using USB B Port J3 and program as described in VeriFire Tools on-line help.
For older PCs without USB connectors, NFS2-640/E and NCA-2 must be temporarily disconnected and separately programmed,
because VeriFire Tools also uses the network/service port. Follow VeriFire Tools instructions for off-line programming mode.
If the NFS2-640/E with NCA-2 is connected to a network, there are two additional options for programming: either connect the VeriFire
Tools programming PC to the network port on the NCM/HS-NCM board, or program the NFS2-640/E through another network node.
NOTE: This is the only NCA-2 application that does not require an NCM or HS-NCM connection to Noti•Fire•Net.
3.5.3 Using the NCD as Primary Display on the NFS2-640

The NCD can be directly connected to the NUP port of the CPU2-640.
The NFS2-640/E can be set up to use the NCD as the primary display.
When the NCD is used as the primary display, the KDM-R2 needs to be removed.
When using the NCD as an alternate display for the NFS2-640 on a standard Noti•Fire•Net, the panel becomes standalone and is not net-
workable, since there is only one NUP port available on the NCM. If the panel is on a High-Speed Noti•Fire•Net, the panel can be net-
worked using the second NUP available on the HS-NCM.The NCD can only be mounted on the left side of the DP-GDIS1 dress plate,
Refer to the NCD manual LS10210-051NF-E for more information.
3.6 Mounting Option Boards

If installing option boards into a CAB-4 Series backbox, mount and connect those boards at this time. General instructions follow; the
sections about individual option boards contain any module-specific instructions such as mounting LEM-320’s stacker-connector.
3.6.1 Option Boards in the NFS2-640/E Chassis

Mount option boards in slots 3 and 4 of the NFS2-640/E chassis. (See Figure 3.2, Figure 3.8, and Figure 3.9.) For standoff lengths, see
Table 3.2.
NOTE: Another option board can be mounted above a Loop Expander Module or Network Communications Module; for
ease of access, be sure to complete installation of those devices before mounting a second layer.
NOTE: If using the fourth (right-side) position of the NFS2-640/E chassis, the chassis needs to be installed on the backbox
before option boards or modules are installed in that position. These modules will block access to the keyhole opening.

Installation Mounting Option Boards
Attach LEM-320 or other

option board to 1 inch
standoffs previously installed
on CPU. (See Section 3.6,
Attach KDM-R2 “Mounting Option Boards”).
to chassis rails
2-640_assembly_3-4-2.wmf
Figure 3.8 Attaching Option Boards Behind KDM-R2
Attach option boards to

mounting studs on chassis
backplate (see Section 3.6,
“Mounting Option Boards”)
2-640_assembly_5a-2.wmf
Figure 3.9 Attaching Option Boards to the Right of the CPU
3.6.2 Option Boards in CHS-4L

1. Slide the tabs at the bottom of the option board into slots on the chassis as shown in Figure 3.11.
2. Lay the board back onto the flanges so that the studs line up with mounting holes on the option board.
3. Attach the option board using screws provided with the board, or if installing a second option board, with stand-offs provided with
the second board.

Install stand-offs on these
CHS-4L.wmf
two studs in any one of the
four positions on the chassis.
Chassis
CHS-4L
Figure 3.10 Standoff Locations on CHS-4L
Slots
nfs640-
Insert tab of option board
into slot of chassis, and lay One option board Two option boards
the option board back in CHS-4L in CHS-4L
against standoffs.
Figure 3.11 Mounting an Option Board in a Chassis (CHS-4L Shown)

Installation Mounting Option Boards
3.6.3 Option Boards on BMP-1 in Dress Panels

Option boards can be mounted on BMP-1 blank module plate, inside dress panels such as DP-DISP2, ADP2-640, ADP-4B, as shown in
Figure 3.12.
Mount BMP-1 onto compatible

dress panel or backbox trim ring
tm4adp4.cdr
Single-space
blank plate
Mount option board

onto standoffs on the
BMP-1
Fasten option board to the

plate with four screws
(included).
Figure 3.12 Mounting an Option Board onto a Dress Panel with BMP-1 (ADP-4B Shown)
NOTE: See the BMP-1 Product Installation Drawing for details if considering mounting the module behind blank module
plate in a dress plate or annunciator backbox. This dress plate is suitable for modules that do not need to be visible or
accessible when the door is closed.
3.6.4 Transmitter Module TM-4

TM-4 is power-limited. Connections are on TB10 nonresettable output and TB11 EIA-485 ACS Mode. Refer to the Transmitter Module
TM-4 installation document for installation details.
3.6.5 Loop Expander Module

Installing a Loop Expander Module adds a second SLC loop to the
control panel. Refer to Figure 3.14 for stacker-connector illustrations.
1. Plug short end of the stacker-connector into J4 on the CPU2-640.
2. Align the LEM with the four 1 inch standoffs and the stacker-
connector as shown in Figure 3.14; firmly seat the stacker-
connector.
3. Attach LEM to standoffs using screws or another set of standoffs.
4. After LEM is mounted on the control panel, connect the SLC
loops to TB1 on the LEM and TB13 on the CPU2-640. This
system supports either FlashScan or CLIP mode devices. Refer to
the SLC loop manual for wiring requirements and specific
details.
LEM-SLC.wmf
Attach stacker-connector to CPU as

shown in Figure 3.14.
Figure 3.13 SLC Connections for LEM-320
CAUTION: For the SLC to function correctly, the stacker-connector must be installed as shown in Figure 3.14. Do not
! install other option modules on top of the LEM-320.

1 inch standoffs
LEM-320 CPU2-640
Stacker-connector
J4
J1
The short-pin end plugs

directly into the top of the
CPU2-640 plug.
The long-pin end

plugs into the back
of the LEM board.
Figure 3.14 Mounting LEM-320 with the Stacker-connector
3.6.6 Network Communications Module

If networking two or more control panels or network control annunciators, each unit requires a Network Communications Module
(NCM) or a High-Speed Network Communications Module (HS-NCM); wire and fiber versions of each are available. The wire and/or
fiber versions of the NCM or the HS-NCM can be installed in any standard option-board position (see Section 3.6 “Mounting Option
Boards”); the default position is immediately to the right of the control panel.
Mount the NCM/HS-NCM in the selected position and screw in place firmly.
Connect J1 on the control panel to J3 on the NCM or J6 of the HS-NCM using the network cable provided (P/N 75556) as described in
the NCM Installation Document and the HS-NCM Installation Document. Do not connect two NCM/HS-NCMs via NUP ports (aka NUP
to NUP).
When installing the NCM: Connect Channel A and/or Channel B as described in the NCM Installation Document.
When installing the HS-NCM: Connect Channel A to Channel B as described in the HS-NCM Installation Document
NOTE: See the Noti•Fire•Net Manual or the High-Speed Noti•Fire•Net Manual and NCM Installation Document or HS-NCM
Installation Document for wiring diagrams and system configuration information. See the BMP-1 Product Installation
Drawing if considering mounting the module behind blank module plate in a dress plate or annunciator backbox.
NOTE: Over-bending fiber-optic cable can damage it. Do not exceed a 3 inch (7.62 cm) minimum bend radius.
NOTE: NCM hardware is not compatible with HS-NCM hardware and should not be mixed on the same network.
3.6.7 DVC Digital Voice Command

Each DVC Series model is a multi-featured audio processor with digital audio functionality that operates as an event-driven audio mes-
sage generator and router. It is designed for use with the DAA2, DAX, DAA Series digital audio amplifiers, and the DVC-RPU Remote
Paging Unit, as well as the DS-DB distribution boards, in a single panel or networked environment, and may also be used as an analog
audio source or configured as a remote paging unit. Refer to the DVC Manual and DVC-RPU Manual.
The NFS2-640/E may be directly connected to the DVC for single panel applications. An associated NCA-2 is required when a DAL
(digital audio loop) is part of the configuration; this configuration supports NUP-to-NUP-to-NUP configuration for single panel DAL
applications.

Installation Connecting the Power Cables
Network configurations require an associated NCA-2, and will support all Network Control-by-Event; each node (DVC, CPU-2 and
NCA-2) requires a network address/NCM port in network applications.
NOTE: The DVC Series consists of all the model versions listed in the bullets below this note. Individual part numbers are
used in this manual only when it is necessary to distinguish features or functions that differ. The term DVC is used in all other
cases.
• DVC-EM - Digital Voice Command, extended memory, wire version (standard)
• DVC-EMF - Digital Voice Command, extended memory, multi-mode fiber version
• DVC-EMSF - Digital Voice Command, extended memory, single-mode fiber version.
For information regarding audio storage for the DVC-EM Series models listed above, refer to the DVC Digital Voice Command Manual.
NOTE: The term DAA is used in this manual to refer to all DAA wire and fiber models. Individual part numbers are used only
when it is necessary to distinguish features or functions that differ.
Figure 3.15 gives simplified overview illustrations of typical applications for the DVC Series and its Digital Audio Loop (DAL).
Wire and fiber, or multi-mode and single-mode, can be mixed.
With DVC and NFS2-640 DVC

DVC-AO for
retrofits. DAL
(Digital Audio
2-640DV1.wmf
Loop) not
compatible
with this
application.
2-640DV2.wmf
With DVC, NFS2-640

NCA-2, DVC
DAL, and DAL DAL DAL
DVC-AO Devic Device
for retrofits.
NCA-2
DVC-AO
Figure 3.15 Block Diagrams of DVC Series Applications
3.7 Connecting the Power Cables

WARNING:
! REMOVE ALL POWER SOURCES TO EQUIPMENT WHILE CONNECTING ELECTRICAL COMPONENTS. LEAVE THE
EXTERNAL, MAIN POWER BREAKER OFF UNTIL INSTALLATION OF THE ENTIRE SYSTEM IS COMPLETE.
WARNING:
! SEVERAL SOURCES OF POWER CAN BE CONNECTED TO THE CONTROL PANEL. BEFORE SERVICING THE
CONTROL PANEL, DISCONNECT ALL SOURCES OF INPUT POWER INCLUDING THE BATTERY. WHILE ENERGIZED,
THE CONTROL PANEL AND ASSOCIATED EQUIPMENT CAN BE DAMAGED BY REMOVING AND/OR INSERTING
CARDS, MODULES, OR INTERCONNECTING CABLES.
3.7.1 Overview
Complete all mounting procedures and check all wiring before applying power. Electrical connections include the following:
• Primary AC power source – 120 VAC, 50/60 Hz, 5.0 A (with NFS2-640E use 240 VAC, 50/60 Hz, 2.5 A) from line voltage source.
Overcurrent protection for this circuit must comply with Article 760 of the National Electrical Code (NEC) and/or local codes. Use
12 AWG (3.31 mm2) wire (maximum) with a 600-volt rating.
• Secondary power source – 24 VDC from batteries, installed in the control panel (or in an optional battery cabinet). Secondary
(battery) power is required to support the system during loss of primary power.
• External power sources – 24 VDC power for Smoke Detectors (4 wire), NACs, and Annunciators.
• Auxiliary power source – 24 VDC power @ 0.5 A and 5 VDC power @ 0.15 A from TB2 on the CPS-24/E.
See Appendix B.1 “Electrical Specifications” for details and overall installation guidelines.

Connecting the Power Cables Installation
3.7.2 Connecting the Control Panel to AC Power

Connect primary power as follows (see Figure 3.16):
TB1 - AC Power Connection
1. Turn off the circuit breaker at the main power distribution panel.
2. Open the hinged insulating cover on TB1.
3. Connect the service ground to terminal marked Ground (Earth). Hot
4. Connect the primary neutral line to terminal marked NEUTRAL and the primary Neutral
Hot line to terminal marked HOT. Ground
5. Close the hinged insulating cover over TB1. (Earth)
Figure 3.16 CPS-24/E:

AC Power Connections
3.7.3 Checking AC Power

Table 3.5 contains a checklist for checking the system with AC power applied:
CAUTION:
! While checking AC power, make sure batteries are not connected.
Follow the sequence of steps in Section 3.2 “Installation Checklist”, Table 3.1; this is Step 15.
Component Status
Control panel circuit board The green AC Power indicator on; the system Trouble indicator on because batteries are not connected.
Each option board The yellow Trouble indicator may come on for approximately 10 seconds after applying AC power. (This only applies to an
unconfigured system.)
Each auxiliary power The yellow Trouble indicator comes on because batteries are not connected.
supply
Table 3.5 AC Power Checklist
3.7.4 Installing and Connecting the Batteries

WARNING:
! BATTERY CONTAINS SULFURIC ACID WHICH CAN CAUSE SEVERE BURNS TO THE SKIN AND EYES, AND CAN
DESTROY FABRICS. IF CONTACT IS MADE WITH SULFURIC ACID, IMMEDIATELY FLUSH SKIN OR EYES WITH
WATER FOR 15 MINUTES AND SEEK IMMEDIATE MEDICAL ATTENTION.
WARNING:
! DO NOT CONNECT THE BATTERY INTERCONNECT CABLES (P/N 75560 AND 75561) AT THIS TIME. MAKE THIS
CONNECTION AFTER INITIAL SYSTEM PRIMARY POWER UP. FOLLOW SEQUENCE OF STEPS IN SECTION 3.2
“INSTALLATION CHECKLIST”, TABLE 3.1; THIS IS STEP 16.
Batteries are installed in the control panel cabinet or in a separate battery cabinet
TB3 - Battery Connection
which can be mounted below the control panel or up to 20 feet (6.096 m) away
from the control panel, in conduit in the same room.
Battery (+) Battery (-)
Connect the battery as follows (see Figure 3.16 above):
1. Install batteries into bottom of cabinet or into separate battery cabinet.
CPS-24-DC.wmf
2. Connect the red cable from TB3(+) on the CPS-24/E power supply to the
positive (+) terminal of one battery.
+24V AUX COM COM +5V AUX
3. Connect the black cable from TB3(–) on the CPS-24/E power supply to the
negative (–) terminal of the other battery.
4. Connect the remaining cable between the negative (-) terminal on the first
battery to the positive (+) terminal on the second battery.
Figure 3.17 CPS-24/E:

DC Power Connections

Installation Connecting the Power Cables
3.7.5 External DC Power Output Connections

Terminal TB10 provides two (2) power outputs, resettable and non-resettable. Each output is power-limited, Class B wiring. Supervise
with a power supervision relay EOLR-1. Follow sequence of steps in Section 3.2 “Installation Checklist”, Table 3.1; this is part of
Step 6. TB2 (on CPS-24), TB10 and all 4 NACS share a maximum of 3.0 A in standby and 6.0 A in alarm.
Non-resettable Resettable
Power Power
CPU2-640-
Figure 3.18 Power Supply DC Outputs - TB10
24 VDC Resettable Power Circuit (Four-Wire Smoke Detectors). The power supply provides a single 24 VDC filtered,
power-limited, resettable power circuit for devices that require resettable power (such as four-wire smoke detectors). This circuit is
power-limited, but must be supervised. To provide supervision, install a UL-listed end-of-line power supervision relay (such as the Sys-
tem Sensor model EOLR-1) after the last device. Connect the power supervision relay normally open contact in series with an Initiating
Device Circuit (IDC). The four-wire power circuit energizes the power supervision relay. When you reset the system, the control panel
removes power from these terminals for approximately 15 seconds.
Connect external field wires to the power supply terminals TB10 RESET(+) and (–) to provide up to 1.25 A of current for powering
four-wire smoke detectors. 1.5 A max for special applications.The total current drawn from the power supply by TB2, TB6 through TB9
and TB10 cannot exceed 3.0 A in standby or 6.0 A in an alarm condition. The Control Panel provides a total of 4.4 A of power in standby
and 7.4 A of power in alarm to be shared by all internal circuitry and external provisions (24 V
resettable and non-resettable). See Figure 3.18 above. TB2 (on CPS-24), TB10 and all 4 NACS share a maximum of 3.0 A in standby
and 6.0 A in alarm.
24 VDC Non-resettable Power Circuit The power supply provides one 24 VDC filtered, power-limited, non-resettable power output,
capable of up to 1.25 A. Use this circuit to power devices that require low-noise 24 VDC power (such as annunciator model ACM-24AT
or the transmitter module TM-4).
Connect external field wires to power supply terminals TB10 NONRESET(+)and(–) to provide up to 1.25 A of non-resettable current for
powering external devices such as annunciators. See Figure 3.18 above. TB2 (on CPS-24), TB10 and all 4 NACS share a maximum of
3.0 A in standby and 6.0 A in alarm.
CAUTION:
! DURING SYSTEM RESET, POWER REMAINS AT TERMINALS TB10 NONRESET(+)AND(–).
3.7.6 Accessories DC Power Output Connections

Terminal TB2 supplies one (1) non-resettable, power-limited 24 VDC circuit and one non-resettable, power-limited 5 VDC circuit avail-
able to power external devices. Class B wiring is possible. Supervise with a power supervision relay EOLR-1. Applications that require
a 5V connection to the Accessories Output, such as an UZC-256, must be within 10 feet (3.658 meters) of the power supply. The dis-
tance from the power supply to the accessory requiring power must not extend past the length of the supplied cable, P/N 75657 (supplied
with UZC-256), which is 10 feet long. Do not splice or otherwise extend P/N 75657. Refer to section B.2, "Wire Requirements" of this
manual for all applications requiring a 24V connection. Connect wiring with all power sources off.
• 24 VDC (nominal) @ 0.5 A max
• 5 VDC (nominal) @ 0.15 A max

NAC Connections and Releasing Circuits Installation
24V - Blue Wire
AMPS24_TB2access.wmf
COM - Black Wire
COM - Black Wire
5V - Red Wire
Figure 3.19 Connecting to the Accessories Output TB2 on CPS-24/E
3.8 NAC Connections and Releasing Circuits

The control panel provides four NAC terminals as shown in Figure 3.21. Each can be configured as Class B or Class A as shown in
Figure 3.20. Each circuit can provide 1.5 A of current, but the total current drawn from the main power supply cannot exceed 7.4 A in
alarm condition (refer to Table A.2). Additionally, TB10, TB2, and all 4 NACs share a maximum of 3.0 A in standby and 6.0 A in alarm;
see Appendix A. NAC circuits are supervised and power-limited. Use UL-listed 24 VDC notification appliances only (refer to the
Device Compatibility Document).
UL-listed ELR-2.2K, 1/2 W (supplied)
TB9 - NAC #1
TB8 - NAC #2
Unused Circuits Class B Connection Class A Connection
Figure 3.20 Notification Appliance Circuit (NAC) TB7 - NAC #3

Connections
TB6 - NAC #4
Figure 3.21 NAC Terminals and NAC LEDs
NOTE: Any NAC can be programmed as a releasing circuit, and the releasing circuit must be supervised; see Figure 4.8–Figure 4.10. For
more information, refer to Section 4 “Applications” in this manual and the NFS2-640/E Programming Manual. Refer to the Device
Compatibility Document for UL-listed compatible releasing devices. Sample connections for NAC terminals are shown in Figure 3.20. Follow
sequence of steps in Section 3.2 “Installation Checklist”, Table 3.1; this is part of Step 6.

Installation NAC Connections and Releasing Circuits
3.8.1 Stat-X Devices

Figure 3.22 shows typical wiring for STAT-X devices using the Ematch Protection Device (P/N 3005014). When using Stat-X devices,
note the following:
• Each Stat-X device requires an Ematch Protection Device to protect +
against high-voltage transient signals, such as lightning, that may
cause the device to accidentally release. Releasing Circuit
• Multiple Stat-X devices can be connected in series (as shown). _
• No more than ten (10) Stat-X devices can be connected on a single
releasing circuit. Green
Yello Ematch Protection
• A REL-2.2K can be installed on a single Stat-X device for short
circuit detection. For multiple Stat-X devices installed in series, the Red Device
Blac P/N 3005014
REL-2.2K is installed on the last device on the releasing circuit (as
shown). A REL-2.2K is required for ULC applications.
• Stat-X devices are not to be used with the FCM-1 or FCM-1-REL.
REL-2.2K
StatXMultiEOL.wmf
Stat-X
Stat-X
Stat-X
Figure 3.22 Wiring Diagram for Stat-X Devices
3.8.2 FSA-8000 Wiring:

Figure 4 shows the wiring for the FSA-8000 detector to the
fire alarm control panel. To Next SLC Device -
SLC From FACP or Previous Device -
For installation information for the FSA-8000 detector, Connection From FACPToorNext SLC Device +
Previous Device +
To Next Device +
refer to the FSA-8000 FAAST Installation and 24V External From Power Supply or Previous Device +
Power To Next Device -
Maintenance Instruction document, part number I56-3903. From Power Supply or Previous Device -
FAASTTermBlk.wmf
Installation Considerations:
The following installation factors should be taken into
consideration when installing the FSA-8000 FAAST
detector:
Detectors per up to 75 total

Figure 4 FSA-8000 Connection to the FACP
Loop:
Modules per up to 45 total

Loop:
Power Supply: FACP AUX or use a power supply UL listed

for fire protective signaling use with
regulated outputs.
Programming Options:
The following programming options should be set when programming the NFS-320, NFS-320SYS, NFS2-640 and NFS2-
3030 with the FSA-8000:
Loop Protocol: CLIP for detectors
Type ID: Acclimate
FlashScan Type ID: None

Output Relay Connections Installation
3.9 Output Relay Connections

The panel provides a set of Form-C relays. These are rated for 2.0 A at 30 VDC
(resistive):
• Alarm - TB4
• Trouble - TB4
• Supervisory - TB5
• Security - TB5
These are power-limited only if connected to a power-limited source.
Using VeriFire Tools, the Supervisory and Security contacts can also be config-
CPU2-640-relays.wmf
ured as Alarm contacts. Follow instructions in the VeriFire Tools online help.
Figure 3.1 Form-C Relay Connections
3.10 Backup-Alarm Switches
WARNING: DO NOT ENABLE THE BACKUP OPTION SWITCH FOR ANY OF THE FOUR NOTIFICATION APPLIANCE
! CIRCUITS (NACS) IF THEY ARE USED FOR RELEASING FUNCTIONS!
Backup alarm switches are provided that enable NACs and the alarm relay to activate
during a backup alarm condition. If the main board’s microcontroller fails and an alarm
is reported by any detector or a monitor module that has backup reporting enabled, the
NAC will turn on if the corresponding switch was enabled. The alarm will activate
during microcontroller failure regardless of the settings of switches SW1–SW4.
CPU2-640-
• SW1 - NAC#1
• SW2 - NAC#2
• SW3 - NAC#3
• SW4 - NAC#4
Figure 3.2 Backup Alarm Switches
So, for example, if SW1 and SW4 were enabled at the time of an alarm during micro-
controller failure, NAC#1 and NAC#4 would activate. Follow sequence of steps in Sec-
tion 3.2 “Installation Checklist”, Table 3.1; this is Step 7.

Installation UL Power-limited Wiring Requirements
3.11 UL Power-limited Wiring Requirements

Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at
least 0.25 inches (6.35 mm) from any nonpower-limited circuit wiring. All power-limited and nonpower-limited circuit wiring must
enter and exit the cabinet through different knockout and or conduits. To maintain separation, group non-power limited modules
together, i.e., group modules on the same side of the enclosure or in separate rows.
Figure 3.3 shows one configuration that meets these UL requirements. The first two rows of modules are configured with at least a 0.25
inch (6.35 mm) separation between power-limited and nonpower-limited wiring; AC and battery wiring is routed away from power-lim-
ited wiring.
Power-limited Circuits*
Power-
limited
circuits
Maintain vertical
separation where NPL
circuits appear to
“cross”
NPL
Nonpower-
320-2-640-PWRLMTWIR-
limited
circuits
To cabinet-mounted battery
(nonpower-limited)
Figure 3.3 Typical Wiring for UL Power-limited Wiring Requirements

(Shown with relays as connected to power-limited modules)
NOTE: AC and battery wiring are not power-limited. Maintain at least 0.25 inches (6.35mm) between power-limited and non power-limited
circuit wiring. Install tie wraps and adhesive squares to secure the wiring. Use a power-limited source for relay output on terminals TB8-
TB11. Figure 2.2, “CPU2-640/CPU2-640E and Power-Supply: Wiring Connections” on page 13
NOTE: Drawing is not to scale. Proportions and angles are exaggerated to show wire-placement more clearly.
NOTE: If additional knockouts are added to the backbox, proper separation of power-limited and non power-limited wiring should be
maintained.
3.11.1 Labeling Modules and Circuits

At the time of installation, each nonpower-limited circuit connected to ACM-8R, and LDM-R32 modules must be identified in the space
provided on the cabinet door label when connected to a non-power-limited source of power.
The label lists all compatible power-limited modules and circuits; also see Figure 2.2 on page 13. The LDM-R32 is power-limited only
when connected to power-limited sources. When connected to a non-power-limited source, the power-limited marking must be removed.

Installing EIA-485 Devices Installation
3.12 Installing EIA-485 Devices

Figure 3.4 provides a closer view of the EIA-485 connections provided on TB11. Because specific connections can vary by the type of
device being connected, refer to the product installation manual for details.
640tb200.wmf
cpu2-
Figure 3.4 EIA-485 Connections
3.13 Installing Remote Printers and/or CRT

3.13.1 Custom Cable Fabrication
A custom cable needs to be fabricated to connect the PRN Printer, Keltron Printer or the CRT-2 Monitor to the system. Length of the
cable will vary with each installation, but should not exceed a maximum length of 50 feet (15.24 m). Printer must be installed in the
same room as the panel, within 20 feet (6.10 meters) and the cable must be installed in conduit. Construct cable as follows:
1. Using overall foil/braided-shield twisted-pair cable, properly connect one end to the DB-25 or DB-9 Connector using the wiring
specifications shown in the table below.
2. Tighten clamp on connector to secure cable.
DB-9 Connector DB-25 Connector TB12 on Control Panel
Pin 2 Pin 3 TX
Pin 3 Pin 2 RX
Pin 5 Pin 7 REF
3.13.2 Installing and Configuring the PRN Series Printer

When connected to the Control Panel via an EIA-232 interface, the PRN prints a copy of all status changes within the control panel and
time-stamps the printout with the time of day and date the event occurred. It provides 80 columns of data on standard 9" by 11" tractor-
feed paper.
NOTE: You can also use the EIA-232 printer interface with UL-listed information technology equipment, such as personal
computers, to monitor the control panel for supplementary purposes.
This section contains information on connecting a printer to the control panel and for setting the printer options.
Connecting a Remote PRN Series Printer
Remote printers require a 120 VAC, 50/60 Hz primary power source. If required for the fire alarm system configuration (for example, a
Proprietary Fire Alarm System), a remote printer requires a secondary power source (battery backup). Because a secondary power
source is not provided, use a separate Uninterruptable Power Supply (UPS) that is UL-listed for Fire Protective Signaling. You may use
your building emergency power supply, so long as it meets the power continuity requirements of NFPA 72. Refer to NFPA 72 for further
details.
Connect the remote printer to the Control Panel as follows:
1. Connect the three (3) open leads of the custom cable to the TB12 terminal block on the control panel as shown in Figure 3.5.
2. Plug the DB-25 or DB-9 connector end of the custom cable into the EIA-232 port of the remote printer. Tighten securely.

Installation Installing Remote Printers and/or CRT
DB-25 connector on PRN series printer (female socket shown) DB-9 Connector on PRN series Printer
DB9printer.
Terminate one end of
shield at backbox
CPU2-640-
Control Panel
NOTE: Outputs are power-limited but are not supervised
Figure 3.5 Remote Printer Connections
Setting Printer Options

Refer to the documentation supplied with the PRN series printer for instructions on using the printer menu controls. Set the printer
options (under the menu area) according to the settings listed in Table 3.6.
Option Setting Option Setting

Font HS Draft CPI 10 CPI
LPI 6 LPI Skip 0.5
ESC Character ESC Emulate Epson FX-850 PRN-6, LQ-2550 PRN-7
Bidirectional Copy ON I/O
CG-TAB Graphic Buffer 40K PRN-6, 64K PRN-7
Country E-US ASCII Serial
Auto CR OFF Baud 9600, 4800, or 2400
Format 7 Bit, Even, 1 Stop
Color Option Not Installed
Protocol XON/XOFF
Formlen Character Set Standard
Lines 6LPI=60
Sl.Zero On
Standard Exec 10.5” PRN-6, 11” PRN-7
Auto LF Off
PAPER
BIN 1 12/72"
BIN 2 12/72"
SINGLE 12/72"
PUSH TRA 12/72"
PULL TRA 12/72"
PAP ROLL 12/72"
Table 3.6 PRN Setup Options
3.13.3 Installing and Configuring a Keltron Printer

Connect the remote printer to the Control Panel as follows:
2. Connect DC power from TB10 terminal block on the control panel as shown in Figure 3.6.
3. Plug the DB-25 connector end of the custom cable into the EIA-232 port of the Keltron printer. Tighten securely.

Installing Remote Printers and/or CRT Installation
Keltron printer Keltron printer

24 VDC connections DB-25 connector
(14 AWG, 2.08 mm2) (female socket shown)

shield at backbox
Control Control
CPU2-640-
Panel Panel
Figure 3.6 Keltron Printer Connections
Setting up the Keltron Printer

Set up a Keltron printer as follows:
1. The printer communicates using the following protocol:
• Baud Rate: 9600 • Parity: Even • Data bits: 7
2. Set the printer DIP switches SP1 and SP2 according to settings in Table 3.7.
SP1 On Off SP2 On Off

1 X 1 X
2 X 2 X
3 X 3 X
4 X 4 X
5 X 5 X
6 X 6 X
7 X 7 X
8 X 8 X
Table 3.7 Keltron DIP Switch Settings
3.13.4 Installing and Configuring a CRT-2

A CRT-2 can only be used in a non-networked application when used with the NFS2-640/E. For further details on setting up the CRT-2,
refer to the NFS2-640/E Operations Manual.
Connect a CRT-2 to the Control Panel as follows:
2. Plug the DB-25 connector end of the custom cable into the EIA-232 port of the CRT-2. Tighten securely.
3. Set parameters as discussed in Table 3.7.

Installation Installing Remote Printers and/or CRT
DB-25 connector
on CRT-2
(female socket shown)

shield at backbox
Control
nfs640-
Panel
Figure 3.7 Connecting a CRT-2
Setting CRT-2 Parameters

The CRT-2 communicates with the control panel through a protocol defined by thirteen groups of parameters. To access a parameter
group, press the corresponding function key (F1-F12) as shown in Table 3.8 below. You can then program parameters in each group.
Enter the CRT-2 setup menu by pressing and holding the <Ctrl> key while pressing the <Scroll Lock> key. Use arrow keys to move
through the selections in each setup group; press the space bar to view the options for each parameter. When finished programming all
setup groups, press the <Pause> key. To save all changes, press <Y>.
Table 3.8 shows the standard settings for using the CRT-2 with the NFS2-640/E; for one instance where these settings may change
slightly see Section 3.13.5 “Connecting Multiple Printers, CRTs, or CRT/PRN Combination”. The basic settings for using the CRT-2
with NFS2-640/E are:
• Baud Rate 9600 • Data format 8 1 N • Protocol xon/off.
NOTE: This section covers installation only; for information on how the CRT-2 functions as part of the fire alarm system, see
the NFS2-640/E Operations Manual.
NOTE: The CRT cannot be connected at the same time as the network

Installing Remote Printers and/or CRT Installation
Function Key CRT-2 Parameters

F1: Quick Emulation=CRT-2 EIA Baud Rate=9600 EIA Data Format=8/1/N
(“Read Status” key) Comm Mode=Full Duplex Aux Baud Rate=9600 Aux Data Format=8/1/N
Enhanced=On Language=U.S. Host/Printer=EIA/Aux
F2:Genrl Emulation=CRT-2 Enhanced=On Auto Wrap=Off
(“Alter Status” key) Auto Font Load=On Auto Page=Off Auto Scroll=On
Monitor Mode=Off Bell Volume=09 Warning Bell=On
Host/Printer=EIA/Aux
F3: Displ Page Length=24 Screen Length=26 Lines Screen Video=Normal
(“Prog” key) Display Cursor=On Cursor=Blink Line Auto Adjust Cursor=On
Columns=80 Width Change Clear=Off Speed=Normal
Scroll=Jump Refresh Rate=60 Hz Overscan Borders=Off
F4: Kybd Language=U.S. Char Set Mode=ASCII Key Mode=ASCII
(“Spl Funct” key) Keyclick=Off Key Repeat=Off Margin Bell=Off
Key Lock=Caps Keyboard Present=Yes
F5: Keys Enter Key=<CR> Return Key=<CR> Backspace=<BS>/<DEL>
(“Prior” key) Alt Key=Meta Disconnect=Pause Desk Acc=Disabled
Pound Key=U.S.
F6: Ports EIA Baud Rate=9600 EIA Data Format=8/1/N EIA Parity Check=On
(“Next” key) Aux Baud Rate=9600 Aux Data Format=8/1/N Aux Parity Check=On
EIA Xmt=Xon-Xoff EIA Recv=Xon-Xoff(XPC) EIA Xmt Pace=Baud
Aux Xmt=Xon-Xoff Aux Recv=Xon-Xoff(XPC) Aux Xmt Pace=Baud
EIA Break=Off EIA Modem Control=Off EIA Disconnect=2 sec
Aux Break=Off Aux Modem Control=Off Aux Disconnect=2 sec
F7: Host Comm Mode=Full Duplex Local=Off Recv <CR>=<CR>
(“Auto Step” key) Recv <DEL>=Ignore Send ACK=On Send Line Term=<CR><LF>
Send Block Term=<CR> Null Suppress=On
F8: Print Prnt Line Term=<CR><LF> Prnt Block Term=<CR> Secondary Recv=Off
(“Activ Signal” key)
F9: Emul Attribute=Page Bright Video=Off Page Edit=Off
WPRT Intensity=Dim WPRT Reverse=Off WPRT Underline=Off
WPRT Blink=Off Display NV Labels=Off Save Labels=On
Status Line=Off Fkey Speed=Normal
F10 Setup Group F10 does not affect communications with the control panel.
F11 Setup Group F11 does not affect communications with the control panel.
F12: Prog Program the function keys as follows: F1 ~A F2 ~B F3 ~C F4 ~D F5 ~E F6 ~F F7 ~G
(“Ack Step” key) F8 ~H F9 ~I F10 ~J F11 ~K F12 ~L F13 ~M F14 ~N F15 ~O F16 ~P Shift F13 ~Q
Table 3.8 Standard CRT-2 Settings for Use with NFS2-640/E
3.13.5 Connecting Multiple Printers, CRTs, or CRT/PRN Combination

Connecting multiple devices requires changing the CRT-2 setup using the F1(Quick) menu:
• Set Host/Printer=EIA/AUX.
• Set EIA Data Format=8/1/N.
• If the AUX device is a printer, set the Printer and AUX Data Format=7/1/E.
• If the AUX device is a second CRT-2, set the AUX Data Format=8/1/N.
Connect multiple devices as shown in Figure 3.8.
To Control Panel
TB12-PC/CRT REF
TB12-PC/CRT TX
TB12- PC/CRT RX
To AUX Port of CRT-2 To EIA-232 port of CRT-2

(female socket shown) (female socket shown)
prncrt-
To EIA-232 port of next

CRT-2 or PRN (female socket shown)
Note: For wire requirements, see Table B.1 in Appendix B.1 “Electrical Specifications”.
Figure 3.8 Connecting Multiple Devices on the EIA-232 Circuit

Installation Wiring a Signaling Line Circuit (SLC)
3.14 Wiring a Signaling Line Circuit (SLC)

 Overview
Communication between the control panel and intelligent and addressable initiating, monitor, and control devices takes place through a
Signaling Line Circuit (SLC). You can wire an SLC to meet the requirements of NFPA Style 4, Style 6, or Style 7 circuits. This manual
provides requirements and performance details specific to this control panel; for installation information and general information, refer
to the SLC Wiring Manual.
 Wiring
Maximum wiring distance of an SLC using 12 AWG (3.31 mm2) wire is 12,500 feet (3810 meters) total twisted-pair for Style 4, Style 6
and Style 7 circuits.
 Capacity
The NFS2-640/E provides one (1) SLC, with a total capacity of 318 intelligent/addressable devices:
• 01-159 intelligent detectors
• 01-159 monitor and control modules
An optional expander board provides one (1) additional SLC, with the same capacity.
Units employing multiple detector operation shall include a minimum of two detectors in each protected space and reduce the detector
installation spacing to 0.7 times the linear spacing in accordance with National Fire Alarm Code, NFPA. For spacing requirements refer
to the detector’s installation instruction.
NOTE: To meet the ten-second response time required by UL 864, 9th edition, when SLC loops are configured to run in CLIP mode, all
input modules must be set to address 19 or lower on both loop one and 2. There are no limits to detectors or output modules.
 Installation
This control panel supports one or two SLC loops; a second SLC loop is obtained by installing an LEM-320 module. SLC loop #1 con-
nects to TB13 on the control panel; SLC loop #2 connects to TB1 on the LEM-320. For details on designing, installing and configuring
SLC loops, see the SLC Wiring Manual.
SLC Loop #1 Connections SLC Loop #2 Connections

on FACP’s main circuit board on Loop Expander Module
SLC B SLC A
nfs640-slcloops.cdr, NFS2640-SLC-TB.wmf,
SLC B (output loop)
SLC A (loop return)
T-Tapping is not allowed

on a four-wire SLC.
Use either
SLC Loop #1
or SLC Loop #2
Style 4 SLC Loops Style 6 SLC Loops
Figure 3.9 SLC Loop Connections and Wiring

Connecting a PC for Off-Line Programming Installation
3.15 Connecting a PC for Off-Line Programming

A PC can be hooked up to the control panel to allow the VeriFire Tools programming utility to upload and download the operating pro-
gram. Refer to the insert in the VeriFire Tools CD insert and to the program’s on-line help function for instructions. There are two
options for connection:
1. For PCs with USB Ports, connect the PC to USB B via a standard USB B cable.
2. For PCs without USB Ports, connect the PC’s serial port to the Control Panel Network/Service Connection (J1, NUP).
NOTE: Download operations that change the basic program of the control panel must be performed by responsible service personnel in
attendance at the control panel. After downloading a program, test the control panel in accordance with NFPA 72.

Section 4: Applications
4.1 Overview
Chapter Covers the following topics
Section 4.3 “NFPA 72 Central or Remote Station How to install UDACT/UDACT-2 with the control panel for use as a NFPA Central or Remote Station
Fire Alarm System (Protected Premises Unit)” Fire Alarm System (Protected Premises Unit)
Section 4.5 “NFPA 72 Proprietary Fire Alarm How to set up a Protected Premises Unit to communicate with a listed compatible Protected Premises
Systems” Receiving Unit.
Section 4.6 “Fire/Security Applications” How to use the control panel as a combination Fire/Security system, including the following:
• Installing a Security Tamper Switch into the cabinet
• Circuit Wiring
Section 4.7 “Releasing Applications” How to install the following releasing applications:
• Releasing Device to the Control Panel (NAC integral circuits)
• Releasing Device to the FCM-1 Module
• Releasing Device to the FCM-1-REL Module
• NBG-12LRA Agent Release-Abort Station
Table 4.1
Municipal Box (Auxiliary)
Municipal Box applications require a TM-4 Transmitter module. Refer to the TM-4 Transmitter Module installation document for instal-
lation details.
4.2 Devices Requiring External Power Supervision

With software version 12.0 or higher, certain type codes have external power supervision (FlashScan only) built into the software. An
external power-supervision relay is required (see Figure 4.1) unless one of the following typecodes is selected for the device:
• Control • Rel Ckt Ulc • Gen Trouble
• Strobe • Nonreset Ctl • Gen Pend
• Horn • Alarms Pend • Trouble Pend
• (Blank) • Gen Alarm
• Release Ckt • Gen Supervis
Power Supervision
Relay (EOLR-1)
(Not required for
FlashScan type codes SLC from FACP
that provide built-in
power supervision.) –
+
Non-resettable 24 +
VDC Power from –
a listed source
Device to be 3030-external-power-
Supervised *If the SLC device
does not match the
N.C. Supervision one in this figure,
Relay Contact refer to the SLC
Part of EOLR-1 FCM-1
(Not required for
manual appendix,
FlashScan type codes which contains wir-
that provide built-in ing conversion
power supervision.) charts for type V and
Figure 4.1 Enabling External Power Supervision Using Relays
4.3 NFPA 72 Central or Remote Station Fire Alarm System (Protected Premises Unit)
Figure 4.2 shows typical wiring diagram for a NFPA 72 Central Station Fire Alarm System (Protected Premises Unit) or a Remote Sta-
tion Fire Alarm System (Protected Premises Unit) using the Universal Digital Alarm Communicator/Transmitter (UDACT or UDACT-
2) and control panel. This provides typical wiring only; connect and program the UDACT or UDACT-2 according to the directions given
in the UDACT Instruction Manual or UDACT-2 Instruction Manual.
NOTE: An NFPA 72 Central Station or Remote Station requires 24 hours of standby power and 5 minutes in alarm.
NOTE: This application can also be done with the TM-4 Transmitter; refer to the TM-4 Transmitter Module installation
document for more details.

NFPA 72 Central or Remote Station Fire Alarm System (Protected Premises Unit) Applications
NOTE: For additional setup information for the UDACT-2, refer to the UDACT-2 Instruction Manual.
Ferrite cores
FACP Cabinet P/N 29090
To supervised Solid earth

phone lines ground
24 VDC EIA-485
Nonresettable power (ACS Mode)
Supervised and power-limited

EIA-485 and power wiring
CPU2-640-
UDACT in ABS-8RB
(shown with cover removed)
Figure 4.2 Typical Wiring Diagram for a Central Station Fire Alarm System
NOTE: Install a UL-listed 120 ohm End-of-Line resistor (P/N 71244) UDACT TB1 terminals 3 and 4 if this is the last or only device on EIA-
485 line.

Applications Central Station Fire Alarm System Canadian Requirements
4.4 Central Station Fire Alarm System Canadian Requirements

For Canadian applications requiring a second dial-out option, refer to the following illustration for UDACT/UDACT-2 and TM-4 setup:
NOTES:
• Drawing is not to scale.
EIA-
PRI SEC
• The UDACT/UDACT-2 should be
set for “Receive Only” for this
LINE SEIZE
LED 3 LED 15
LED 4 LED 16
LINE FAIL
LED 5 LED 17
NO TONE TB2 TB1
LED 6 LED 18
KISS OFF ACS + ACS - REF REMOTE REMOTE REMOTE MUNICIPAL
configuration. For additional

LED 7 LED 19 BOX
STATION STATION STATION
COMM FAIL
TB3 SW1 ALARM TROUBLE SUPERVISORY
UDACT-2
+24VDC REF ELR
TM-4 UDACT/UDACT-2 setup

+ 24V
+ 24 { information, refer to the UDACT
EIA-485 COMM LOSS
LED 1
REAL TIME
LED 2
+ 24V
_ {
LED 8
_
POWER
Installation Manual. or UDACT-2

LED 9 TXACS RXACS
24
COMMON
LED 13
+
LED 14
LED2 LED1
LED 20
_
Rela EIA-+_{ Instruction Manual.
EIA- { • This illustration is show with the
INPUT 5
TRANS TEST POWER
INPUT 4
NCM-W. For other NCM or HS-
CLEAR REPORT RESET
LED4 SW6
NON-ISOLATED
ISOLATED
SW2 SW3 SW4
SW4
NCM setup, refer to the NCM

DISABLE
SW2
INPUT 3
Installation or HS-NCM
ENABLE
INPUT 2
SW3
LED3
TONE DETECT
LED21
TROUBLE SW5
1
INPUT 1
Installation documents.
1
SW1 ON
OPTION ON
SELECT
• For additional setup information on

SWITCH
1 2 3 4 OFF
the TM-4, refer to the TM-4

Instruction Manual.
ON
NO
0 C
18/24 NC
115
230
MR-101/C
FMM-1
EIA-485
_ + _
+
SLC
To
Previous
24V + EF B TERM B EF A TERM A
OFF
OFF
SW101
SW103
SW102
SW100
_
ON
ON
NFS2-640/E
LED101 LED100
J3 J2
A HI B HI
LED6 LED7
NUP2
NUP1
RCDA RCDB
LED4 LED2
STATA STATB
LED3 LED5
NCM-W
RECON PULSE1
LED1 LED8
LCM A
RESET POWER
LCM B
LCM TERM
A A
OFF
ON
SW1
SW2
To Next
EF B TERM B EF A TERM A
OFF
OFF
SW101
SW103
SW102
SW100
ON
ON
NCA-2
LED101 LED100
J3 J2
A HI B HI
LED6 LED7
NUP2
NUP1
RCDA RCDB
LED4 LED2
STATA STATB
LED3 LED5
RECON PULSE1
LED1 LED8
NCM-W
LCM A
RESET POWER
LCM B
LCMTERM
A A
OFF
ON
SW1
SW2
Figure 4.3 Central Station Canadian Requirements for Second Dial-Out Connection

NFPA 72 Proprietary Fire Alarm Systems Applications
4.5 NFPA 72 Proprietary Fire Alarm Systems

When connected and configured as a protected premises unit with UDACT or UDACT-2, the NFS2-640/E will automatically transmit
General Alarm, General Trouble, and General Supervisory signals to a listed compatible Protected Premises Receiving Unit. See the
UDACT Manual or UDACT-2 Manual for compatible receiving units. A simplified drawing of connections between the receiving unit
and the NFS2-640/E protected premises unit is shown in Figure 4.4.
Connect the receiving unit to the protected premises unit as shown in Section 4.3 “NFPA 72 Central or Remote Station Fire Alarm Sys-
tem (Protected Premises Unit)”.
For information on installing and programming the Receiving unit, refer to the documentation for that control panel.
Telephone line & backup
UDACT or
UDACT-2
Compatible Receiving Unit

(see UDACT Manual or UDACT-2 NFS2-640/E
Manual)
NFS2-640/E Protected Premises Unit
Figure 4.4 Typical Proprietary Fire Alarm Systems Wiring Connections
4.6 Fire/Security Applications
NOTE: NFS2-640/E is not approved for use in security applications in Canada.
4.6.1 General Operation

The control panel can be used as a combination Fire/Security system when installed and operated according to the instructions in this
section.
For security applications, program one or more monitor modules (listed for security applications) with the SECURITY Type Code, and
wire as shown in Figure 4.6. Activating this type of module lights the SECURITY LED, and displays a security alarm condition on the con-
trol panel LCD display. The panel sounder will sound until the Security alarm is acknowledged. You can also program additional sound-
ers or output devices to activate with the security alarm initiating device. The SECURITY Type Code is designed to indicate an alarm as
follows: (a) on an open or short circuit; or (b) on a ±50% change in resistance value from the End-of-Line resistor value.
A tamper switch installed in the cabinet door will indicate a door tamper condition whenever the door is open. If the control panel indi-
cates a Security alarm, you can acknowledge, silence, and reset the condition from the control panel.
When the system resets, a 30-second exit timer starts. During this time the tamper switch and all Security alarms are ignored. There is no
entrance delay timer.
For bypass of security zones, use the DISABLE routine (covered in the Status Change section of the NFS2-640/E Operations Manual)
for Security type devices.
WARNING:
! Damage can result from incorrect wiring connections.
4.6.2 Installing a Security Tamper Switch

To wire the cabinet with a Security Tamper Switch kit model STS-1, refer to Figure 4.5:
1. Install the STS-1 Tamper Switch onto the side of the backbox opposite the door hinge, pushing the switch through the opening until
it snaps into place.
2. Install the magnet on the same side of the cabinet door as the lock. Push the magnet through the opening in the door until it snaps
into place.
3. Connect the STS-1 connector to J5 (Security Tamper) on the Control Panel. (As shown in Figure 4.5, J5 is located on the circuit
board, underneath the edge of KDM-R2.)

Applications Fire/Security Applications
Connect to
J5 “Security Tamper”
LED7
LED6
LED5
LED4
LED3
LED2
LED1 J6 J5
STS-1 mounting location

(side opposite of door hinges)
CPU2-640-
Figure 4.5 Installing the STS-1 Security Tamper Switch
4.6.3 Receiving Unit

For applications requiring transmission of security alarm information to a central receiving unit, the control panel may be connected via
the UDACT or UDACT-2 to a compatible receiving unit (see the UDACT Manual or UDACT-2 Manual). For information on configuring
the Receiving unit for Combination Fire/Security applications, refer to the documentation for that control panel.
4.6.4 Programming
The control panel can communicate with any number of security devices. To do so, program the points as follows:
1. Select the address of the module(s) to be used for security.
2. Select the Type Code SECURITY.
NOTE: For detailed instruction on programming Type Codes, refer to the NFS2-640/E Programming Manual.
4.6.5 Wiring for Proprietary Security Alarm Applications

Table 4.6 shows typical wiring for proprietary security alarm applications with FMM-1 modules. Note the following:
• The module is programmed with software SECURITY Type Code.
• For use with UL listed systems only; application not for ULC security usage.
• NAC devices used for security cannot be shared with fire NAC devices.
• Refer to the Device Compatibility Document for compatible NAC devices.
• All monitor modules used for security application must be installed in the NFS2-640/E cabinet with STS-1 Security Tamper Switch.
NFS2-640/E Protected Premises Unit
SLC
UL-listed 47K UL-listed, Channel
End-of-Line Resistor normally-open A or B
(provided with module) security switch
*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
CPU2-640-
which contains wir-

UL-listed, normally-closed ing conversion
security switch FlashScan Monitor Module charts for type V and
Figure 4.6 Wiring Diagram for Proprietary Security Alarm Applications

Releasing Applications Applications
4.7 Releasing Applications

WARNING:
! WHEN USED FOR CO2 RELEASING APPLICATIONS, OBSERVE PROPER PRECAUTIONS AS
STATED IN NFPA 12. DO NOT ENTER THE PROTECTED SPACE UNLESS PHYSICAL
LOCKOUT AND OTHER SAFETY PROCEDURES ARE FULLY COMPLETED. DO NOT USE
SOFTWARE DISABLE FUNCTIONS IN THE PANEL AS LOCKOUT.
WARNING:
! DO NOT ENABLE THE BACKUP OPTION SWITCH FOR ANY OF THE FOUR NOTIFICATION
APPLIANCE CIRCUITS (NACS) IF THEY ARE USED FOR RELEASING FUNCTIONS!
4.7.1 Overview
This control panel can be used for agent release or preaction/deluge control applications. In a properly configured system with compati-
ble, listed actuating and initiating devices, this control panel complies with the following NFPA standards for installation in accordance
with the acceptable standard:
Standard Covers
NFPA 12 CO2 Extinguishing Systems
NFPA 12A Halon 1301 Extinguishing Systems
NFPA 13 Sprinkler Systems
NFPA 15 Water Spray Systems
NFPA 16 Foam-Water Deluge and Foam-water Spray Systems
NFPA 17 Dry Chemical Extinguishing Systems
NFPA 17A Wet Chemical Extinguishing Systems
NFPA 2001 Clean Agent Fire Extinguishing Systems
Table 4.2 NFPA Standards for Releasing Applications

To locate your specific releasing applications, including type codes and wiring diagrams, see the checklist in Table 4.3:
Refer to
Section 4.7.2 “Programming”
Section 4.7.3 “Connecting a Releasing Device to the Control Panel”.
Section 4.7.4 “Connecting a Releasing Device to the FCM-1 Module”.
Section 4.7.6 “Connecting an NBG-12LRA Agent Release-Abort Station”.
Table 4.3 Locating Specific Releasing Application Details in This Manual
4.7.2 Programming
The control panel supports up to ten releasing software zones. You can map these zones to activate Control Panel releasing outputs and
FCM-1 modules. Program the FCM-1 module for the appropriate type code according to the chart below:
Type Code: RELEASE CKT Type Code: REL CKT ULC

• For use in UL applications. • For use in UL or ULC applications.
• Do not use REL device at the solenoid. • Requires REL device at solenoid.
• Cannot use power-limited wiring. • Power-limited wiring.
• Supervised for open circuit only. • Supervised for open circuit and shorts.
• Supervised for power loss with power-supervision relay. • Supervised for power loss with power-supervision relay.
For more information, refer to the NFS2-640/E Programming Manual.
4.7.3 Connecting a Releasing Device to the Control Panel

Use TB6 (NAC#4), TB7 (NAC#3), TB8 (NAC#2), or TB9 (NAC#1) on the control panel for NAC⁄Releasing Circuits. The releasing cir-
cuit must be supervised and use listed, compatible releasing devices; see Figure 4.8–Figure 4.10 (page 50).

Applications Releasing Applications
B+ NAC/Releasing output (source)

B– NAC/Releasing output (source)
A+ Class A (return for NAC only)
A– Class A (return for NAC only)
Compatible UL-listed
24 VDC releasing device
CPU2-640-RELCONN1.wmf
Control
Panel
REL-2.2K (Use with Type Code

Rel Ckt ULC, or see Circuit
Note: See text below for circuit requirements. Requirement 4.)
Figure 4.7 Typical Class B Connection of a Releasing Device to Control Panel
WARNING:
! DO NOT ENABLE THE BACKUP OPTION SWITCH FOR ANY OF THE FOUR NOTIFICATION
APPLIANCE CIRCUITS (NACS) IF THEY ARE USED FOR RELEASING FUNCTIONS!
Circuit Requirements. When connecting a releasing device, note the following:
1. The control panel provides four NAC/Releasing Circuits (Class A or Class B). Each circuit can provide 1.5 A. Total current drawn
from the power supply cannot exceed 7.4 A in an alarm condition (refer to Table A.2, “System Draw Current Calculations,” on
page 56). Use compatible UL-listed 24 VDC appliances only. For more information on compatible appliances, refer to the Device
Compatibility Document.
2. Refer to the Releasing Applications appendix in the NFS2-640/E Programming Manual for configuration details (such as setting
the Soak Timer).
3. For applications using power-limited circuits:
a) Use an in-line supervisory device (P/N REL-2.2K) with control panel releasing circuits. Connect the End-of-Line device as
shown in Figure 4.7.
b) Program the releasing circuit for Type Code REL CKT ULC.
c) Circuits are supervised against opens and shorts.
4. For applications not requiring power-limited circuits –
a) If the application does not require supervising the releasing device against shorts, in-line supervisory devices (P/N REL-2.2K)
are not required.
b) In non-power-limited applications, program the releasing circuit for Type Code RELEASE CKT.
c) Limited energy cable cannot be used to wire a non-power-limited releasing device circuit
d) Maintain a 0.25 inch (6.35 mm) spacing between the non-power-limited releasing circuit device wiring and any power-limited
circuit wiring.)
5. The releasing circuit must be programmed with a releasing type code listed in the NFS2-640/E Programming Manual.
NOTE: As per UL 864 9th Edition, a supervisory signal must be indicated at the panel whenever a releasing
circuit is physically disconnected. Use a monitor module to monitor dry contacts off the switch. See 4.11.
IQActuatorsa.wmf
Figure 4.8 Releasing Circuits (Option 1)

IQActuatorsb.wmf
IQActuatorsc2010.w
)
GasDisconnectMod.w
Monitor Module
Mechanical Disconnect Switch listed for the application

Note: Disconnect switch must provide separate dry
contacts to indicate supervisory.
Figure 4.11 Release Circuits (Mechanical Disconnect Switch)
4.7.4 Connecting a Releasing Device to the FCM-1 Module

The module can control 1 A of current. Make sure to keep total system current within the limits of the power supply. You can power the
module from the power supply of the Control Panel or any UL/ULC listed 24 VDC regulated power-limited power supply for Fire Pro-
tective Signaling. For more information, refer to the Device Compatibility Document.
SLC from FACP
or LEM-320
+ Non-resettable Power Supervision
Relay (EOLR-1) –
24 VDC Power +
–
+ –
24 VDC releasing device
–
Brow Red *If the SLC device
+ does not match the
one in this figure,
Relconn-
REL-47K refer to the SLC

(Use with Type manual appendix,
Code N.C. Supervision
Relay Contact FCM-1 which contains wir-
Rel Ckt ULC,
Part of EOLR-1 ing conversion
or see Circuit
charts for type V and
Note: See text for circuit requirements.
Figure 4.12 Typical Connection of a 24 VDC Releasing Device to the FCM-1 Module

Circuit Requirements When connecting a releasing device to the FCM-1 module, note the following:
1. Refer to the Releasing Applications appendix in the NFS2-640/E Programming Manual for configuration details (such as setting
the Soak Timer).
2. For applications using power-limited circuits:
a) Use an in-line supervisory device (P/N REL-47K) with the FCM-1 module. Connect the in-line supervisory device as shown in
Figure 4.12.
b) Program the releasing circuit for Type Code REL CKT ULC.
c) Circuits are supervised against opens and shorts.
3. For applications not requiring power-limited circuits:
a) In-line supervisory devices (P/N REL-47K) are not required; however, the releasing device circuit is not supervised against
shorts.
b) In non-power-limited applications, program the releasing circuit for Type Code RELEASE CKT.
c) Limited energy cable cannot be used to wire a non-power-limited releasing device circuit.
d) Maintain a 0.25 inch (6.35 mm) spacing between the non-power-limited releasing circuit device wiring and any power-limited
circuit wiring.
WARNING:
! THE XP6-C IS NOT LISTED FOR RELEASING APPLICATIONS AND CANNOT BE SUBSTITUTED
FOR FCM-1
NOTE: As per UL 864 9th Edition, a supervisory signal must be indicated at the panel whenever a releasing
circuit is physically disconnected. Use a monitor module to monitor dry contacts off the switch. See 4.11.

4.7.5 Connecting Releasing Devices to the FCM-1-REL Control Module

Typical Connections Figure 4.13 and Figure 4.13 show typical connections for wiring a releasing device to the FCM-1-REL. Refer to
the Device Compatibility Document for compatible releasing devices.
Non-resettable
24 VDC power
(-)
(+)
SLC (-)
Module polarities are shown in alarm condition. SLC (+)
All wiring shown is supervised and power-limited.
24 VDC releasing device.
fcm-1-rel-
One (1) device maximum.
FCM-1-REL
Figure 4.13 NPFA Class B Wiring of the FCM-1-REL

Non-resettable When using the FCM-1-REL for
24 VDC power Class B applications, remove
jumper J1.
Module polarities are shown in alarm condition.

All wiring shown is supervised and power-limited.
(+)
SLC (-)
SLC (+)
(-)
SLC (-)
SLC (+)
fcm-1-1rel-
24 VDC releasing device.
One (1) device maximum.
FCM-1-REL
Figure 4.13 NPFA Class A Wiring of the FCM-1-REL
NOTE: With firmware version 12.0 or higher ALL new FlashScan Mode SLC releasing applications require the
FCM-1-REL control module. The V-type FCM-1 control module may be used in SLC releasing applications with
firmware version 14.0 or higher. H-type FCM-1 control modules do not support FlashScan Mode releasing
applications with firmware version 14.0 or higher. Use H-type FCM-1 for CLIP mode SLC releasing applications, with
firmware version 12.0 or higher.
Critical Requirements. When connecting a releasing device to the FCM-1-REL module, note the following:
1. See “Power Considerations” on page 52 for information on monitoring 24 VDC power.
2. Do not T-tap or branch a Class A or Class B circuit.
3. Only one (1) 24V solenoid or two (2) 12V solenoids in series can be connected to the
FCM-1-REL.
4. Do not loop wiring under the screw terminals. Break the wire run to provide supervision of connections.
5. All applications using the FCM-1-REL are power-limited:
1. Program the releasing circuit for Type Code REL CKT ULC or RELEASE CKT.
2. Circuits are supervised against opens and shorts.
6. Refer to the NFS2-640/E Programming Manual for instructions on setting the Soak Timer.
The FCM-1-REL module must be programmed with the correct releasing type code listed in the NFS2-640/E Programming Manual.

4.7.6 Connecting an NBG-12LRA Agent Release-Abort Station

SLC loop to
NBG-12LRA
FMM-101 FACP or LEM-320
See Document 51369 Manual Abort Black
Yellow
for installation details.
Violet Red
Manual Release FMM-1

Black
Red
Normal Non-resettable +24 VDC

ELR mode R-47K
Release from main power supply
supervised and
power-limited
FRM-1
C.
NFS640-
N.C. N.O.
System
Common (–)
Power Supervision
Relay (EOLR-1)
24 VDC power FCM-1

from FACP’s *If the SLC device
main power supply does not match the
one in this figure,
24 VDC UL-listed refer to the SLC
releasing device
manual appendix,
Brown Red which contains wir-
REL-47K N.C. Supervision ing conversion
(use with Type Code Relay Contact charts for type V and
Rel Ckt ULC)
Figure 4.14 Typical Connections for an NBG-12LRA Agent Release-Abort Station
NOTE: If using the on-board NACs, see Circuit Requirements for Section 4.7.3 “Connecting a Releasing Device
to the Control Panel” on page 49. If using FCM-1, see Circuit Requirements for Section 4.7.4, “Connecting a
Releasing Device to the FCM-1 Module”, on page 51. If using the FCM-1-REL, see Circuit Requirements for
Section 4.7.5, “Connecting Releasing Devices to the FCM-1-REL Control Module”, on page 53.

Section 5: Testing the System
5.1 Acceptance Test
When finished with the original installation and all modifications, conduct a complete operational test on the entire installation to verify
compliance with applicable NFPA standards. Testing should be conducted by a factory-trained fire alarm technician in the presence of a
representative of the Authority Having Jurisdiction and the owner’s representative. Follow procedures outlined in NFPA Standard 72’s
section on Inspection, Testing and Maintenance.
5.2 Periodic Testing and Service

Periodic testing and servicing of the control panel, all initiating and notification devices, and any other associated equipment is essential
to ensure proper and reliable operation. Test and service the control panel as required by the Authority Having Jurisdiction and according
to the schedules and procedures outlined in the following documents:
• NFPA Standard 72’s section on Inspection, Testing and Maintenance.
• Service manuals and instructions for the peripheral devices installed in the system. Correct any trouble condition or malfunction
immediately.
5.3 Operational Checks

Before proceeding: a) notify the fire department and the central alarm receiving station if transmitting alarm conditions; b) notify facility
personnel of the test so that alarm sounding devices are disregarded during the test period; and c) when necessary, disable activation of
alarm notification appliances and speakers to prevent their sounding.
• Disconnect all releasing devices to prevent accidental activation in accordance with NFPA 2001 and NFPA 12A releasing agents.
WARNING:
! Do not rely on disable/enable software settings to lockout releasing devices.
• Check that the green POWER LED lights.

• Check that all status LEDs are off.
• Press and hold the LAMP TEST key. Verify that all LEDs and all LCD display segments work.
• Activate an Initiating Device Circuit using an alarm initiating device or an addressable initiating device on the SLC and check that
all programmed active notification appliances function. Reset the alarm initiating device, the control panel, and any other associated
equipment. In voice alarm applications, confirm that the proper tone(s) and/or messages sound during alarm conditions. Select the
paging function and confirm that the message can be heard in the affected fire zones. Repeat the above step with each Initiating
Device Circuit and each addressable device.
• On systems equipped with a fire fighter’s telephone circuit, make a call from a telephone circuit and confirm a ring tone. Answer
the call and confirm communication with the incoming caller. End the call and repeat for each telephone circuit in the system.
• Remove AC power, activate an Initiating Device Circuit through an alarm initiating device or an addressable initiating device on
the SLC, and check that programmed active notification appliances sound, and alarm indicators illuminate. Measure the battery
voltage with notification appliances active. Replace any battery with a terminal voltage less than 21.6 VDC and reapply AC Power.
NOTE: The battery test requires fully charged batteries. If batteries are new or discharged due
to a recent power outage, allow the batteries to charge for 48 hours before testing.
• Return all circuits to their pretest condition.

• Check that all status LEDs are off and the green POWER LED is on.
• Notify fire, central station and/or building personnel when you finish testing the system.
5.4 Battery Checks and Maintenance

Maintenance-free sealed lead-acid batteries used in the system do not require the addition of water or electrolyte. These batteries are
charged and maintained in a fully charged state by the main power supply’s charger during normal system operation. A discharged bat-
tery typically reaches the voltage of 27.6 VDC within 48 hours; the charge rate depends on the battery size (2.0A for 18-26AH; 5.0A-
5.7A for 26AH-200AH).
Batteries should be replaced in accordance with the battery manufacturer’s recommendations. Immediately replace a leaking or damaged
battery.
WARNING:
! Batteries contain Sulfuric Acid which can cause severe burns to the skin and eyes and damage to
fabrics.
• If a battery leaks and contact is made with the Sulfuric Acid, immediately flush skin and/or eyes with water for at least 15 minutes.
Water and household baking soda provides a good neutralizing solution for Sulfuric Acid.
• If Sulfuric Acid gets into eyes, seek immediate medical attention.
• Ensure proper handling of the battery to prevent short circuits.

Testing the System Battery Checks and Maintenance
• Take care to avoid accidental shorting of the leads from uninsulated work benches, tools, bracelets, rings, and coins.
WARNING:
! Shorting the battery leads can damage the battery, equipment, and could cause injury to personnel.

Appendix A: Power Supply Calculations
Calculations must be done to determine standby and alarm DC current loads. Ampere-hour requirements must be calculated as well
to determine battery size. The on-board power supply provides filtered 24VDC power that may be used for operating external
devices. Use Table A.2 to determine if external loading is within the capabilities of the power supply.
A.1 Calculating AC Branch Circuit Current

Use Table A.1 below to determine the total amount of current, in AC amperes, that a 120 VAC, 50/60 Hz service must be able to
supply to the fire alarm system. Devices rated for 240 VAC operation will draw approximately one-half the current listed in Table
A.1.
No. of
Device Type Current (amps) Total Current
Devices
CPS-24 Power Supply [ 1 ] X 5.0 = 5.0
CPS-24/E Power Supply [ .. ] X 2.5A =
AA-30 [ ] X 1.00 =
AA-120 [ ] X 1.85 =
FCPS-24S6/S8 [ ] X 3.2 =
ACPS-2406 [ ] X 2.7* =
ACPS-610 [ ] X 5.0* =
ACPS-610/E [ ] X 2.5 =
APS-6R [ ] X 2.5 =
CHG-120 [ ] X 2.0 =
Sum column for AC Branch Current required=amps
Table A.1 120 VAC Fire Alarm Circuit

* Separate calculations are required for any devices powered by the ACPS-2406 and ACPS-
610. It has its own integral battery charger and batteries can be connected directly to it. Refer to
the ACPS-2406 or ACPS-610 Installation Manuals for battery calculations.
AC Branch Circuit Installation: For guidelines on wiring the AC branch circuit current, see “Operating Power: AC Branch Circuit” on
page 72 in Appendix B.1 “Electrical Specifications”.
A.2 Calculating the System Current Draws

The control panel’s main power supply must be able to power all internal system devices (and several types of external devices)
continuously during non-fire alarm conditions. Use column 1 in Table A.2 to calculate the Non-Fire Alarm Load on the power
supply regulator when applying primary power. The main power supply must also provide a finite amount of additional current
during a fire alarm condition. Use column 2 in Table A.2 to calculate the additional current needed during fire alarms. The
requirements for non-fire alarm and fire alarm current loads cannot exceed the capabilities of the power supply as listed below:
• 4.4 A at 24 VDC during Standby; and
• 7.4 A at 24 VDC during Alarm.
The current draw from all NACs plus DC output from TB10 and TB2 is 3.0 A during standby and 6.0 A during alarm.
How to Use the Calculating Tables
As used in this section, “Primary” refers to the control panel’s on-board power supply, its primary source of AC power. “Secondary”
refers to the control panel’s backup batteries (or any other 24 VDC power supply listed for Fire Protective Signaling and connected
in place of the batteries). The term “standby” refers to the output current required when no fire alarm is present. The term “alarm”
refers to the output current required when a fire alarm is present.
The Primary Power Source Non-Alarm Current and Alarm Current columns are DC current calculations. These calculations
confirm that the power supply can provide enough current to support the system during Primary Non-Fire Alarm and Fire Alarm
conditions.
Quantities List the number of devices powered by the FACP and its power supply. Devices powered by the Accessories Output
(TB10 and TB2) draw current directly from the panel. Devices powered by the Panel Output draw current through the fire panel’s
connection to the power supply. Use these quantities to calculate total current draw of each set of devices in calculation columns 1,
2, and 3.

Add the contents of calculation column 1 to get the current drawn
Calculation Column 1 (Primary, Non-Fire Alarm Current in amps)
from the power supply during a non-alarm condition, with AC power applied. This current draw cannot exceed 4.4 A without an
auxiliary power supply.
Calculation column 2 lets the system designer determine the current load
Calculation Column 2 (Primary, Fire Alarm Current in amps)
that the power supply must support during a fire alarm. The total current draw during a fire alarm cannot exceed 6 A without an
auxiliary power supply.
Typically, a system should contain capacity to activate all output circuits and relays, and support fire alarms on no less than 10% of
Initiating Device Circuits, subject to the requirements of the Authority Having Jurisdiction (AHJ).
The Control Panel provides power for Notification Appliance Circuits. Refer to the Device Compatibility Document for 24 VDC
notification appliances that are UL- and ULC-listed for fire alarm systems.
Calculation Column 3 [Secondary (Battery) Non-Alarm Current] Column 3 lets the system designer calculate the non-fire alarm current
drawn from the secondary source in a non-fire alarm condition during AC power loss.The non-fire alarm current is required to
complete the standby battery calculations. After summing all current draws, insert the total in Table A.3.
Calculation Column 1 Calculation Column 2 Calculation Column 3

Category Primary, Non-Fire Alarm Primary, Fire Alarm Secondary, Non-Fire Alarm
Current (amps) Current (amps) Current (amps)
X [current X [current X [current
Qty Total Qty Total Qty Total
draw]= draw]= draw]=
CPU2-640/E 1 x [0.250] = 1 x [0.250] = 1 x [0.250] =
# NACs in use (0, 1, 2, 3 or 4)* [ ] x [0.035] [ ] x [0.035] [ ] x [0.035]
CPS-24/E n/a n/a n/a n/a n/a x [0.040]
KDM-R2 (Backlight on) [ ] x [0.100]= [ ] x [0.100]= [ ] x [0.100]=
LEM-320 0/ x [0.100]= 0/ x [0.100]= 0/ x [0.100]=
1 1 1
SLC loop†: 1/2 x [.200]= 1/2 x [.200]= 1/2 x [.200]=
NCA, NCA-2 (Back light ON) [ ] x [0.400]= [ ] x [0.400]= [ ] x [0.400]=
NCA, NCA-2 (Back light OFF) [ ] x [0.200]= [ ] x [0.200]= [ ] x [0.200]=
NCM-W, NCM-F [ ] x [0.110]= [ ] x [0.110]= [ ] x [0.110]=
HS-NCM-W/MF/SF/WMF/WSF/ [ ] x [0.400]= [ ] x [0.400]= [ ] x [0.400]=
MFSF [ ] x [0.110]= [ ] x [0.175]= [ ] x [0.110]=
TM-4 [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
DPI-232 (Refer to manual**)
APS-6R [ ] x [0.025]=
APS2-6R [ ] x [0.0013]=
ACPS-2406, ACPS-610
DVC components (Refer to [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
manual**) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
AA-30 [ ] x [0.045]=
AA-100, AA-120 [ ] x [0.050]=
ACM-24AT [ ] x [0.016]= [ ] x [0.070]= [ ] x [0.016]=
ACM-48A [ ] x [0.016]= [ ] x [0.070]= [ ] x [0.016]=
AEM-24AT [ ] x [0.002]= [ ] x [0.056]= [ ] x [0.002]=
AEM-48A [ ] x [0.002]= [ ] x [0.056]= [ ] x [0.002]=
Maximum number of LEDs [ ] x [0.0054]= [ ] x [0.0054]=
illuminated on these annunciators
during non-fire conditions:
AFM-16AT, AFM-32A [ ] x [0.040]= [ ] x [0.056]= [ ] x [0.040]=
ACM-16AT, ACM-32A [ ] x [0.040]= [ ] x [0.056]= [ ] x [0.040]=
AEM-16AT, AEM-32A [ ] x [0.002]= [ ] x [0.018]= [ ] x [0.002]=
AFM-16A [ ] x [0.025]= [ ] x [0.065]= [ ] x [0.025]=
ACM-8R (refer to manual**) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
LDM (refer to manual**) [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
FDU-80 LCD-80, LCD2-80 [ ] x [0.0643]= [ ] x [0.0643]= [ ] x [0.0643]=
[ ] x [0.100]= x [0.100]= x [0.050]=
AMG-1, AMG-E [ ] x [0.060]= [ ] x [0.060]= [ ] x [0.060]=
RM-1 [ ] x [0.020]= [ ] x [0.020]= [ ] x [0.020]=
FZM-1, MMX-2 [ ] x [0.0094]= [ ] x [0.090]= [ ] x [0.0094]=
Table A.2 System Draw Current Calculations (1 of 2)

Calculation Column 1 Calculation Column 2 Calculation Column 3
Category Primary, Non-Fire Alarm Primary, Fire Alarm Secondary, Non-Fire Alarm
Current (amps) Current (amps) Current (amps)
RPT-W, RPT-WF, RPT-F [ ] x [0.017]= [ ] x [0.017]= [ ] x [0.017]=
RPT-485W, RPT-485WF
UDACT Communicator [ ] x [0.040]= [ ] x [0.100]= [ ] x [0.040]=
UDACT-2 Communicator [ ] x [0.052]= [ ] x [0.087]= [ ] x [0.052]=
NFV-25/50 (see manual**) [ ] x[ ]= x[ ]= x[ ]=
Four-Wire Smoke Detectors‡ [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
[ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
Power Supervision Relay [ ] x [0.020]= [ ] x [0.020]= [ ] x [0.020]=
EOLR-1
FWSG (only if powered by the [ ] x [0.040]= [ ] x [0.040]= [ ] x [0.040]=
FWSG 24V connections TB:A2
and TB:A3)
Notification Appliance powered [ ] x[ ]=
from Main Power Supply** [ ] x[ ]=
DHX-501, FSD-751RP, FSD- [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
751RPL (Duct Detectors with [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
internal relays)
Refer to installation document
CHG-120 Battery Charger [ ] x [0.060]=
Local Energy Municipal Box [ ] x[ ]=
Compatible Devices not listed [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
above†† [ ] x[ ]= [ ] x[ ]= [ ] x[ ]=
Sum each column for totals Primary, non-alarm: Primary, alarm: Secondary, non-alarm:
Table A.2 System Draw Current Calculations (2 of 2)

* Maximum current draw for all NACs plus DC output from TB10 and TB2 is 3.0 A during standby.
† Value represents an SLC’s maximum current draw. Refer to device datasheets for individual current draws.
‡ The total regulated load current supplied to four-wire smoke detector and power supervision relays cannot exceed 1.25 A.
** Enter the total notification appliance draw from the Main Power Supply, excluding the current from APS-6R supplies. Refer to Device
Compatibility Document.
†† Refer to manual and/or Device Compatibility Document. See Table 1.1, “Reference Documentation,” on page 8 for specific documentation part
numbers.
A.2.1 Calculating the Maximum Secondary Power Fire Alarm Current Draw
Use Table A.3 below to determine the maximum current requirements of secondary power source during fire alarm conditions. The
result obtained is the amount of current that the batteries must be able to supply to the fire alarm system. Use the result in Table A.4
to determine the size of the batteries needed for the fire alarm system.
Results taken from Table A.3 below assume that, while in a fire alarm condition, batteries must feed the main power supply (and
any additional supplies such as the APS-6R and AA-30) with the maximum rated power each supply can provide.
Current
Device Quantity Total Current/Type
(in amps)
Alarm Current, from Table A.2, col 2 =
*
APS-6R [ ] X 6 =
APS2-6R [ ] 6 =
AA-30† [ ] X 3 =
AA-120 [ ] X 7.3 =
Sum Column for Secondary Fire Alarm Load =
Table A.3 Maximum Secondary Power Fire Alarm Current Draw

* Actual load current may be used in place of maximum rated supply current. To calculate
actual load current, sum the current draws for each appliance connected to APS-6R
supplies.
† Exclude Amplifiers that are employed for backup.
NOTE: The Secondary Fire Alarm Load cannot exceed the following:
12 A with BAT-12260 batteries (12 V, 26 AH).
20 A with BAT-12550 batteries (12 V, 55 AH).

A.3 Calculating the Battery Requirements
A.3.1 Calculating the Battery Capacity
Use this table to determine the battery capacity needed for the system:
Current (amps) X Time (hours) = AH
Secondary Non-Fire Alarm Current (from Required Secondary Non-Fire Alarm Standby
column 3 in Table A.2) Time (24 or 60 hours)
(see Note 8)
X ________________ = _________AH
________________
APS-6R Required Secondary Non-Fire Alarm Standby
Standby Load Current Time (24 or 60 hours)
________________ X ________________ = _________AH

Secondary Fire Alarm Load Required Fire Alarm Standby Time: (for 5
(from Table A.3) minutes, enter 0.084; for 15 minutes, enter 0.25)
(see Note 8) ________________

X = _________AH
________________
Sum Column for Total Secondary Amp Hours calculated = _________AH
Multiply by the derating factor x 1.2 (see Note 7) = _________AH
Battery Size – Total Secondary Amp Hours Required = _________AH
1. NFPA 72 Local, Proprietary, and Central Station systems require 24 hours of standby power followed by 5 minutes in alarm.
2. NFPA 72 Auxiliary and Remote Station Systems require 24 hours of standby power followed by 5 minutes in alarm.
3. Batteries installed in a system powered by an automatic starting engine generator need to provide at least 4 hours of standby power.
4. Factory Mutual requires 90 hours of standby for deluge-preaction systems.
5. Emergency voice/alarm communications systems require 2 hours of operation in the alarm condition. Due to the sporadic nature of voice
operation, however, NFPA 72 permits 15 minutes of operation at a maximum connected load to equal 2 hours of normal use.
6. If the total exceeds 26 AH, the system requires a separate NFS-LBB, BB-100 or BB-200 battery enclosure for two larger capacity batteries.
7. The following battery derating factors must be used for Canadian installations using NFS2-640/E charger:
• For a 26 AH battery, use derating factor of 1.5
8. For 26 AH batteries: maximum standby current cannot exceed 0.65A; maximum alarm current cannot exceed 6.75A.
Table A.4 Secondary Power Standby and Fire Alarm Load
A.3.2 Calculating the Battery Size

Use this table to choose the battery size, in amp-hours, needed to support the fire alarm system.
The CPS-24/E can charge batteries from 18 to 200 AH. Select batteries that meet or exceed the Total Amp-Hours calculated in Table A.4 and that
are within the acceptable battery charger range. Write the amp-hours requirements on the Protected Premises label.
The maximum battery size that can be mounted inside a CAB-4 series backbox is 26AH.
Battery Voltage Number Our Part
Backbox Part Number†
Size Rating Required Number
18 AH 12 volts two BAT-12180 SBB-A4*, SBB-B4*,
SBB-C4*, SBB-D4*, BB-25
26 AH 12 volts two BAT-12260 SBB-A4, SBB-B4,
SBB-C4, SBB-D4, BB-25
100 AH 12 volts four for 100 BAT- BB-100
AH 121000 BB-200
two for 200
AH
*Manufactured to our specifications.
†Red version available; add “R” to part number listed here
Table A.5 Selecting Battery and Battery Backbox

Appendix B: Electrical Specifications
B.1 Electrical Specifications
AC Power
Component Values
Main Power Supply 120 VAC, 50/60 Hz, 5.0 A; or
240 VAC, 50/60 Hz, 2.5 A
Wire size Maximum 12 AWG (3.31 mm2) with 600 VAC insulation
NOTE: If using an auxiliary power supply such as FCPS-24S6/S8, APS-6R, ACPS-2406, or ACPS-610, or
audio amplifiers, refer to the documentation for that equipment.
Batteries
The control panel uses only sealed lead-acid batteries for secondary standby power. Maximum battery capacity for the CPS-24/E main
power supply is 200 AH. CAB-4 Series backboxes provide space for two 26 AH (or smaller) batteries. Use external battery boxes if the
installation requires larger capacity batteries; see Table A.5, “Selecting Battery and Battery Backbox,” on page 58.
The table below contains battery charger specifications.
Charger Description Specifications
CPS-24/E An internal battery charger for 18 Normal Charge: 27.6 VDC +/- 0.24 VDC
Main Power Supply AH to 200 AH Charging Current: 2.0 A or 5.7 A (Software selectable)
CHG-120 An external battery charger Dual Rate: High Charge: 28.1 VDC
Battery Charger designed to charge lead-acid Normal Charge: 27.6 VDC
batteries between 26 AH and 120 Charging Current: 4.5 A
AH
ACPS-2406 An internal battery charger for Normal Charge: 27.6 VDC

Auxiliary 7AH to 26 AH Charging Current: 1.1 A max (0.750 A typical)
Charger/Power Supply
ACPS-610 An internal battery charger for Normal Charge: 27.6 VDC +/- 0.24 VDC
Addressable 12AH to 200AH Charging Current: 2A, 5A, or OFF (Software Selectable)
Charger/Power Supply
Signaling Line Circuit (SLC)

Item Value
Voltage 24 VDC nominal, 27.6 VDC maximum
Maximum length 12,500 ft. (3810 m) total loop or circuit length (NFPA Class A, B, and X)
Note: Refer to Appendix B.2 “Wire Requirements” for limitations.
Maximum current 400 mA peak, 200 mA average (max short circuit; circuit will shut down until
short is fixed). For battery calculation purposes use 200mA.
Maximum resistance 50 ohms (supervised and power-limited)
Notification Appliance Circuits & Releasing Circuits

Item Value
Max. wiring voltage drop 2 VDC
(Retrofit note: SLCs with old CMX modules are restricted to 1.2 VDC.)
NAC Nominal operating 24 VDC regulated, 1.5 A max.
voltage
Special Applications for 20.16 - 26.42 VDC
Releasing Circuits
Current for all external 6.0 A in alarm (3 A continuous)
devices connected to the TB2, TB10 and all 4 NACs share a maximum of 3.0 A in standby and 6.0 in
control panel’s power supply alarm.
Optional ACPS-2406 Total 6 A in alarm (5 A continuous)
Optional ACPS-610 Total 6 A in alarm (1.5 A single output)
Optional APS-6R Total 6 A in alarm (4 A continuous)
End-of-Line Resistors Control Panel NACs (TB6, TB7, TB8, TB9): 2.2K, 1/2 watt
(ELRs) XP6-C, FCM-1 Modules: 47K, 1/2 watt
NOTE: For a list of compatible Notification Appliance Circuits and Releasing Circuits see Notifier Device
Compatibility Document 15378.

Electrical Specifications Wire Requirements
Output Relays
Output relays for Alarm and Trouble are common on TB4; Supervisory and Security are programmable on TB5. See Figure 3.21, “Form-
C Relay Connections” on page 39).
Contact ratings: 2.0 A @ 30 VDC (resistive)
Four-wire Smoke Detector Power
Control Panel terminals TB10 RESET (+) and (–) supply filtered, low-noise power for four-wire smoke detectors. Specifications are:
• Nominal voltage: 24 VDC special applications.
• Maximum rated current: 1.25 A DC
• Maximum ripple voltage: 176 mVrms
• TB10, TB2, and all 4 NACs share a maximum of 3.0 A in standby and 6.0 A in alarm.
Refer to the Device Compatibility Document for compatible 24 VDC detectors.
Power Output
Control Panel terminals TB10 NONRESET (+) and (–) supply one (1) power-limited circuit available to power external devices, such as
notification appliances and annunciators.
• Nominal voltage: 24 VDC regulated, special applications, 1.5 A max.
• Maximum rated current: 1.25 A DC
• Maximum ripple voltage: 176 mVrms
• TB10, TB2, and all 4 NACs share a maximum of 3.0 A in standby and 6.0 A in alarm.
Refer to the Device Compatibility Document for compatible devices and notification appliances.
NOTE: The Control Panel provides a total of 7.4 A of power in alarm (4.4 A in standby), shared
by all internal circuitry and external provisions (24 V resettable and non-resettable). TB10 and all
4 NACs share a maximum of 3.0 A in standby and 6.0 A in alarm. For power requirements, refer
to the power supply calculation tables in Appendix A.
Operating Power: AC Branch Circuit

The control panel requires connection to a separate dedicated AC branch circuit. Follow these guidelines when connecting the AC
branch circuit:
• Label the branch circuit “Fire Alarm”. This must be a separate dedicated AC fire alarm circuit.
• Connect the branch circuit to the line side of the main power feed of the protected premises.
• Do not power other equipment from the fire alarm branch circuit.
• Run the AC branch circuit wire continuously, without any disconnect devices except for overcurrent protection, from the power
source to the fire alarm control panel.
• Overcurrent protection for the AC branch circuit must comply with Article 760 of the National Electrical Codes, as well as local
codes.
• Use 12 AWG (3.31 mm2) wire with 600 VAC insulation for the AC branch circuit.
Connect the ground terminal (TB1-Earth) to a solid earth ground (a metallic, cold water pipe may be suitable in some installations). This
connection is vital in reducing the panel’s susceptibility to transients generated by lightning and electrostatic discharge.
Operating Power: Secondary Power Source (Batteries)
The battery charger is current-limited and can recharge sealed lead-acid type batteries. The battery charger shuts off when the control
panel is in alarm.
B.2 Wire Requirements

Each type of circuit within the Fire Alarm Control System requires use of a specific wire type to ensure proper circuit operation. The
wire gauge of a particular circuit depends on the length of that circuit and the current traveling through it. Use Table B.1 below to deter-
mine the specific wiring requirements for each circuit.
Compliance with the Federal Communications Commission (FCC) and Canadian Department of Communication regulations on electri-
cal energy radiation requires the following: Use twisted-pair shielded wire for any non-SLC-loop wiring entering or exiting the cabinet
that is not enclosed in conduit. Use twisted-pair unshielded wiring for SLC-loop wiring.
NOTE: If running an SLC in conduit with Notification Appliance Circuits, you can reduce
problems by exclusively using electronic sounders (such as the SpectrAlert, SpectrAlert Advanced
or MA/SS-24 Series) instead of more electronically noisy notification appliances (such as
electromechanical bells or horns).

Wire Requirements Electrical Specifications
Circuit Distance
Circuit Type Wire Requirements Typical Wire Type
Function (feet/meters)
SLC Connects to Twisted-unshielded pair, 12 to 18 AWG 12,500 ft. (3,810 m) 12 AWG (3.31 mm2)
(power limited) intelligent and (3.31 to 0.82 mm2). 50 ohms maximum per 9,500 ft. (2,895.6 m) 14 AWG (2.08 mm2)
addressable length of Class A & X loops. 50 ohms per 6,000 ft. (1,828.8 m) 16 AWG (1.31 mm2)
modules. branch maximum for Class B loop. 3,700 ft. (1,127.76 m) 18 AWG (0.82 mm2)
Twisted, shielded pair 5,000 ft. (1,524 m) 12 to 16 AWG (3.31 to
NOTE: 01.31 mm2)
• Shields must be isolated from ground. 3,700 ft. (1,127.76 m) 18 AWG (0.82 mm2)
• Shields should be broken at each
device.
Untwisted, unshielded wire, in conduit or 5,000 ft. (1,524 m) 12 to 16 AWG (3.31 to
outside of conduit. 01.31 mm2)
3,700 ft. (1,127.76 m) 18 AWG (0.82 mm2)
Note: Maximum total capacitance of all
SLC wiring (both between conductors and
from any conductor to ground) should not
exceed 0.5 mircofarads.
EIA-485 Connects to Twisted-shielded pair with a characteristic 6,000/1829 16 AWG (1.31 mm2)
(power limited) FDU-80, ACS impedance of 120 ohms. 18 AWG (0.82 (max)
modules, LCD- mm2) minimum.
80, or TM-4
Transmitter
EIA-232 Connects to Twisted-shielded pair in conduit. 20 feet (6.1 m) 16 AWG (1.31 mm2)
(power limited) Printers, CRT, 18 AWG (0.82 mm2) minimum. (without modem)
or PC.
IDC FMM-1, 12-18 AWG (3.31 to 0.82 mm2). 12 to 18 AWG (3.31 to
Initiating Device FMM-101, Maximum circuit resistance is 20 ohms. 0.82 mm2)
Circuit FDM-1XP10-M,
XP6-MA
(power limited)
NAC FCM-1*, XP6-C 12-18 AWG (3.31 to 0.82 mm2). .To meet 1.2 V drop, 12 to 18 AWG (3.31 to
Notification (power limited) At alarm current level, no more than a 1.2 or sized to provide 0.82 mm2)
Appliance V drop at the end of the circuit, or sized to the minimum rated
Circuit provide the minimum rated operating operating voltage of
voltage of the appliances used. the appliances used.
Releasing FCM-1-REL 12-18 AWG (3.31 to 0.82 mm2). To meet 5 ohms 12 to 18 AWG (3.31 to
Module 5 ohms maximum per circuit for class A or maximum circuit 0.82 mm2)
B, or sized to provide the minimum rated resistance, or sized
operating voltage of the appliances used. to provide the
minimum rated
operating voltage of
the appliances used
24 VDC Power To TM-4 12-18 AWG (3.31 to 0.82 mm2). To meet 1.2 volt drop 12 to 18 AWG (3.31 to
Runs Transmitter, Size wire so that no more than 1.2 V drop 0.82 mm2)
(power-limited) Annunciator and across wire run from supply source to end
FCM-1 modules of any branch.
CHG-120 External battery 12 AWG (3.31 mm2) in conduit 20/6.1 (max) 12 AWG (3.31 mm2)
charger
Note: * FCM-1 cannot be used for synchronized strobe/sounder applications.
Table B.1 Wire Requirements

NOTE: Lightning arresters required on circuits extending between buildings; 999 meter length maximum to
meet UL 60950.

Appendix C: Canadian Applications
C.1 Standalone Application
C.1.1 NFS2-640/E with KDM-R2
If using KDM-R2 as the primary display for NFS2-640/E, an ACS series annunciator must be mounted adjacent to the panel or within
NFS2-640/E enclosure.
C.1.2 NFS2-640/E with NCA-2

Network Control Annunciator (NCA-2) with 640-character, multi-line display complies with ULC requirements when used as the pri-
mary display for NFS2-640/E.
C.2 Network Applications

To meet ULC requirements, the network’s Manual Controls may only be operated from one location at any given time. When panels are
networked (using NCM Network Communications Modules or High-Speed Network Communications Modules), use AKS-1B Key
Switch on each panel’s Primary Annunciator to enable its functions. NCA-2 may be a Primary Annunciator when AKS-1B is installed.
Refer to the NCA-2 Manual for more information.
The NCA-2 or ONYXworks may be employed as a Display and Control Center. In the event that communication fails between the pan-
els and the Control Center, the panels will continue to function in local/standalone mode.
C.3 Automatic Alarm Signal Silence

If selecting this feature for a system requiring annunciators, consult the Authority Having Jurisdiction.
If Auto Silence is enabled, the value must be set to 20 minutes. An ACS point is required to monitor special function zone ZF40.
Activation of Auto Silence will activate the Signal Silence LED on the fire panel display and any ACM LED point programmed for Auto
Silence.
C.4 Annunciator Applications

1. In Canada, the ACM series annunciator modules must be used to annunciate the fire alarm input points/zones only, if no multi-line
sequential display is installed.
2. For Canadian applications, the following LED colors must be employed:
– Red must be used to indicate active alarm inputs.
– Yellow must be used to indicate supervisory, burglary, trouble signals, and Automatic Alarm Signal Cancel.
– Green must be used to indicate the presence of power or an activated output.
3. Two Stage Systems (3/5 minute timer) - ACM-24AT control point is required for Automatic Alarm Signal Cancel. Acknowledge
will not cancel the Two-Stage Timer. For applications using Two Stage with the ACPS-610, see the ACPS-610 manual for
additional programming instructions.
4. The ACM point designated for Automatic Alarm Signal Cancel should be labeled as “Automatic Alarm Signal Cancel” or “Auto
Alm Signal Cancel.”
5. If the DCC option is enabled, an ACS point is required to monitor ZF36 for the panel itself as well as each DCC on the network.
C.5 Releasing Devices

Supervision for shorts is required; use REL devices and type code REL CKT ULC.
(With on-board NACs, use REL-2.2K; with FCM-1 modules use REL-47K. Refer to Section 4.7.5 “Connecting Releasing Devices to the
TC810S1000 Control Module” for details.)
C.6 Ancillary Devices

Panel control functions (Acknowledge, Signal Silence, Reset, and Drill) will not function on ancillary devices such as the ACM-24-AT,
FDU-80, or the LCD2-80. (Local acknowledge will function on the ancillary device to silence the piezo and steady the LEDs).
C.7 Isolating NACs with Audio Isolator Modules

C.7.1 Description of Modules
The audio isolator modules described below may be used to isolate short circuits during alarm signaling. These modules are listed with
ULC for use with the NFS2-640C.
• AIM-1 - This module provides isolation to a separate circuit on an audible notification riser. A short circuit on an AIM-1 NAC circuit
will not disable other NACs circuits on the riser.
• RSM-1 - This module works the same as the AIM-1, with the exception that there is a silence button for in-suite operation. The silence
button will silence the audible signal to the module’s circuit for ten minutes during alarm. Resounding will occur automatically after ten
minutes.

Notes

Index
Numerics F Non-Power-Limited Circuits
24 VDC, see Power (DC) FCM-1 51 UL Wiring Requirements 36
FCM-1-REL 44, 53 Notification Appliance Circuits, see NACs
A Fire/Security Applications 47–48
A77-716B, see Power Supervision Relay FMM-1 48 O
Replaced by EOLR-1 Form-C Relays 35, 62 Operating Power 62
AC, also see Power 31 Four-wire Smoke Detector Operational Checks 55
Acceptance Test 55 Specifications 62 Option Boards
ACM-8R FSA-8000 Wiring Installation Steps 25
Labeling Requirements 36 34 Output Relays
Agent Release-Abort Station 54 Connections 35, 62
Alarm Relays, see Form-C Relays 35 I Specifications 62
Ancillary Devices 64 Installation
Checklist 19 P
B Preparation 18 Periodic Testing 55
Backup-Alarm Switches 35 Power
Basic Equipment Packages 11 J AC Power Checklist 31
Batteries, also see Power: DC Jumper Locations 13, 14 AC Power Connections 31
Battery Calculations 57, 58, 59, 60 AC Specifications 61
Battery Checks and Maintenance 55 DC Power Connections 31, 32
K Installation Steps 30
Battery Specifications 61 KDM-R2
Connections 31 Power Specifications 30, 62
Installation steps 24 Power Supervision Relay 51
Battery Plate 20 Keltron, also see Printers 38
Battery plate 24 Power Supply Calculations 57, 58, 59, 60
Power-Limited Wiring Requirements 36
L Primary Display 11, 25
C LDM-R32 primary display 24
Cabinets 15 Non-Power-Limited Circuits 36 Printers 41
Mounting 19 LED Locations 14 Installation 37–41
Canadian Applications 25, 64 Lockout 55 Keltron Printer Connections 38
Central Receiving Unit, also see UDACT Manual Loop Expander Module PRN Series Connections 37
48 Installation Steps 28 PRN Settings 38
Chassis 27 PRN/CRT Combination 41
Circuit Board, see CPU Proprietary Security Alarm Applications
Compatible Equipment 15 M
Main Power Supply, see Power Supply Wiring 48
Components 13, 14 Protected Premises Unit 44
Control Panel Circuit Board, see CPU Maintenance 55
CPS-24/E, see Power Supply Microcontroller Failure 35
CPU Mounting R
CPU-640 (120V operation) 11 LEM 29 Related Documentation 8
CPU-640E (240V operation) 11 MRD-1 9 Relays, see Form-C Relays 35
Drawing 11, 13, 14 MRD-1 Manual Releasing Disconnect Assembly Releasing Circuits
Overview 11 17 Connections 33
CRTs 41 Multiple Detector Operation 42 Releasing Applications 49–54
CRT/PRN Combination 41 Releasing Applications, Canada 64
CRT-2 Configuration 39 N Specifications 61
CRT-2 Function Keys and Parameters 41 NACs (Notification Appliance Circuits) Releasing Device
Installation 37–41 Backup Option 35 Connections 49
NAC Connections 33 FCM-1 Connections 51
Releasing Applications 35, 49, 50 FCM-1-REL Connections 44, 53
D
DC, also see Power 31 Specifications 61
DVC 29 NBG-12LRA 54 S
NCA-2, also see Primary Display 11 Security Relays, see Form-C Relays 35
NCD 21 Security Tamper Switch 47, 48
E Network 21 Service 55
Electrical Connections 30 Networking 29 SLC 28
Electrical Specifications 61 NFPA Applications SLC, also see SLC Wiring Manual 42
Ematch Protection Device 34 NFPA 72 Central or Remote Station Fire Specifications 61
EOLR-1 see Power Supervision Relay Alarm System 44 Specifications 61, 62
External Power Supervision 44 NFPA Applications (Overview) 44 Stacker-Connector 29

Index
Stand-Off Lengths 23
Stat-X
Device Wiring 34
STS-1, also see Security Tamper Switch 48
Supervisory and Security Contacts
-Configuring as Alarm Contacts 35
Supervisory Relays, see Form-C Relays 35
Supplemental Documentation 8
Switches
Backup-Alarm 35
Switch Locations 13, 14
System
Description of Features 10
Limitations 10
Options 10
System Current Draws 57, 58, 59, 60
T
Terminal Block Locations 13, 14
Testing 55
TM-4, also see TM-4 Installation Document 28
Trouble Relays, see Form-C Relays 35
U
UL Non-Power-Limited Wiring Requirements 36
UL Requirements 36
V
VeriFire 43
W
Wiring
Proprietary Security Alarm Applications
48
Wire Requirements 62

Manufacturer Warranties and Limitation of Liability
Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer
warrants that the Products manufactured by it in its Northford, Connecticut facility
and sold by it to its authorized Distributors shall be free, under normal use and
service, from defects in material and workmanship for a period of thirty six months
(36) months from the date of manufacture (effective Jan. 1, 2009). The Products
manufactured and sold by Manufacturer are date stamped at the time of production.
Manufacturer does not warrant Products that are not manufactured by it in its
Northford, Connecticut facility but assigns to its Distributor, to the extent possible,
any warranty offered by the manufacturer of such product. This warranty shall be
void if a Product is altered, serviced or repaired by anyone other than Manufacturer
or its authorized Distributors. This warranty shall also be void if there is a failure to
maintain the Products and the systems in which they operate in proper working
conditions.
MANUFACTURER MAKES NO FURTHER WARRANTIES, AND DISCLAIMS ANY
AND ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED, WITH
RESPECT TO THE PRODUCTS, TRADEMARKS, PROGRAMS AND SERVICES
RENDERED BY MANUFACTURER INCLUDING WITHOUT LIMITATION,
INFRINGEMENT, TITLE, MERCHANTABILITY, OR FITNESS FOR ANY
PARTICULAR PURPOSE. MANUFACTURER SHALL NOT BE LIABLE FOR ANY
PERSONAL INJURY OR DEATH WHICH MAY ARISE IN THE COURSE OF, OR AS
A RESULT OF, PERSONAL, COMMERCIAL OR INDUSTRIAL USES OF ITS
PRODUCTS.
This document constitutes the only warranty made by Manufacturer with respect to
its products and replaces all previous warranties and is the only warranty made by
Manufacturer. No increase or alteration, written or verbal, of the obligation of this
warranty is authorized. Manufacturer does not represent that its products will
prevent any loss by fire or otherwise.
Warranty Claims. Manufacturer shall replace or repair, at Manufacturer's discretion,
each part returned by its authorized Distributor and acknowledged by Manufacturer
to be defective, provided that such part shall have been returned to Manufacturer
with all charges prepaid and the authorized Distributor has completed Manufacturer's
Return Material Authorization form. The replacement part shall come from
Manufacturer's stock and may be new or refurbished. THE FOREGOING IS
DISTRIBUTOR'S SOLE AND EXCLUSIVE REMEDY IN THE EVENT OF A
WARRANTY CLAIM.
Warn-HL-08-2009.fm

NOTIFIER
12 Clintonville Road
Northford, CT 06472-1610 USA
203-484-7161
www.notifier.com

NFS2-640/E: Fire Alarm Control Panel Installation Manual

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

NFS2-640/E: Fire Alarm Control Panel Installation Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NFS2-640/E: Fire Alarm Control Panel Installation Manual

Uploaded by

Copyright:

Available Formats

Fire Alarm Control Panel

Document 52741 Rev: P9

2 NFS2-640 Installation — P/N 52741:P9 5/13/19

NFS2-640 Installation — P/N 52741:P9 5/13/19 3

4 NFS2-640 Installation — P/N 52741:P9 5/13/19

NFS2-640 Installation — P/N 52741:P9 5/13/19 5

6 NFS2-640 Installation — P/N 52741:P9 5/13/19

1.1.1 UL 864 9th and 10th Edition

NFS2-640 Installation — P/N 52741:P9 5/13/19 7

1.2 Related Documents

Device Compatibility Document 15378

NFS2-640/E Installation, Operations, and Programming Manuals 52741, 52742, 52743

DVC Digital Voice Command Manual 52411

DVC-RPU Manual 50107425-001

DVC-RPU UL Listing Document 50107424-001

DAL Devices Reference Document 52410

DS-DB Digital Series Distribution Board and Amplifier Manual 53622

DAA2 and DAX Amplifiers Manual 53265

SLC Wiring Manual 51253

Off-line Programming Utility Document Number

VeriFire® Tools CD help file VERIFIRE-TCD

Cabinets & Chassis Document Number

CAB-3/CAB-4 Series Cabinet Installation Document 15330

Heat Dissipation for Cabinets with Audio Products* 53645

Battery/Peripherals Enclosure Installation Document 50295

ACPS-2406 Installation Manual 51304

ACPS-610 Installation Manual 53018

APS-6R Instruction Manual 50702

APS2-6R Instruction Manual 53232

CHG-120 Battery Charger Manual 50641

FCPS-24 Field Charger/Power Supply Manual 50059

FCPS-24S6/FCPS-24S8 Field Charger/Power Supply Manual 51977

Networking Document Number

High-Speed NCM Installation Document 54014

Noti•Fire•Net Manual, Network Version 5.0 & Higher 51584

NCM-W/F Installation Document 51533

HS-NFN Installation Document 54013

NCA-2 Network Control Annunciator Manual 52482

NCA Network Control Annunciator Manual 51482

NCD Network Control Display LS10210-051NF-E

System Components Document Number

Annunciator Control System Manual 15842

FDU-80Remote Annunciator Manual 51264

LCD-80 Liquid Crystal Display Remote Annunciator 15037

Table 1.1 Reference Documentation (1 of 2)

8 NFS2-640 Installation — P/N 52741:P9 5/13/19

LCD2-80 Liquid Crystal Display Remote Annunciator 53242

LDM Series Lamp Driver Annunciator Manual 15885

DPI-232 Direct Panel Interface Manual 51499

TM-4 Installation Document (Reverse Polarity Transmitter) 51490

UDACT Manual (Universal Digital Alarm Communicator/Transmitter) 50050

UDACT-2 Manual (Universal Digital Alarm Communicator/Transmitter) 54089

UDACT-2 Listing Document (Universal Digital Alarm Communicator/Transmitter) 54089LD

AA-Series Audio Amplifiers Manual 52526

ACT-1 Installation Document 52527

ACT-2 Installation Document 51118

FireVoice-25/50, FireVoice-25/50ZS & FireVoice-25/50ZST Manual 52290