PRODUCT SELECTION GUIDE

HVAC Insulation
 TABLE OF
CONTENTS

DUCT LINER INSULATION

Linacoustic® RC 3
Linacoustic RC-HP
®
3
Linacoustic R-300
®
3
Spiracoustic Plus 4
®

Spiral SG® 4
LinaTex® 4

DUCT BOARD INSULATION

Superduct® RC 5
Mat-faced Micro-Aire 5®

Micro-Aire® LP 5
Diffuser Board 6

EXTERNAL DUCT INSULATION

Microlite® FSK Duct Wrap 6

Microlite® Black PSK and White PSK Duct Wrap 6
Microlite® Standard Duct Wrap 7
800 Series Spin-Glas® 7

ACCESSORIES

Microlite® White & Black PSK Seaming Tape 7

SuperSeal® & SuperSeal® HV 8
Duct Knife 8

Visit www.JM.com for more information

DUCT LINER INSULATION

Linacoustic® RC
Fiberglass Duct Liner with Reinforced Coating THERMAL PERFORMANCE SPECIFICATION
R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
in mm (hr•ft2•ºF)/Btu m2•ºC/W
ASTM C1071, Type I, Flexible
½ 13 2.2 0.39
1 25 4.2 0.74 ASTM G21 and G22
1½ 38 6.3 1.11 SMACNA Application Standards
2 51 8.0 1.41 for Duct Liners
3 76.2 12.0 2.11
NAIMA Fibrous Glass Duct Liner
Installation
SOUND-ABSORPTION COEFFICIENTS ASTM E84, FHC 25/50
Type A Mounting, Frequency (Hz) NFPA 90A and 90B
in mm 125 250 500 1000 2000 4000 NRC
½ 13 0.07 0.20 0.44 0.66 0.84 0.93 0.55 ICC Compliant
1 25 0.08 0.31 0.64 0.84 0.97 1.03 0.70 Conforms to ASHRAE 62
Linacoustic® RC insulation is a flexible, fiberglass duct liner. The airstream 1½ 38 0.10 0.47 0.85 1.01 1.02 0.99 0.85
Canada: C GSB 51-GP-11M
surface is protected with JM’s exclusive reinforced coating system, a 2 51 0.25 0.66 1.00 1.05 1.02 1.01 0.95
CAN/ULC S102
glass mat surface coated with Permacote® antimicrobial coating. 3 76.2 0.47 0.96 1.17 1.10 1.02 1.05 1.05

Operating Temperature Limit: 250°F (121°C) Recycled Content:

Maximum Air Velocity: 6,000 fpm (30.5 m/sec) Refer to JM.com
Greenguard Certified

Linacoustic® RC-HP
High-Density Fiberglass Duct Liner with Reinforced THERMAL PERFORMANCE SPECIFICATION
Coating and Superior Acoustical Performance R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
in mm (hr•ft2•ºF) /Btu m2•ºC/W
ASTM C1071, Type I
1 25 4.3 0.76
Conforms to ASHRAE 62
MEA #353-93-M
SMACNA Application Standards for
SOUND-ABSORPTION COEFFICIENTS Duct Liners
Type A Mounting, Frequency (Hz) NAIMA Fibrous Glass Duct Liner
in mm 125 250 500 1000 2000 4000 NRC Installation Standard
1 25 0.04 0.24 0.69 0.96 1.05 1.01 0.75 ASTM D5116-State of Washington
Canada: C GSB 51-GP-11M and
CAN/ULC S102
ASTM E84, FHC 25/50
Linacoustic® RC-HP insulation is a flexible, fiberglass duct liner with
higher density and enhanced acoustical control when compared to NFPA 90A and 90B
standard duct liners. The airstream surface is protected with JM’s
exclusive reinforced coating system, a glass mat surface coated Recycled Content:
with Permacote antimicrobial coating. Refer to JM.com
Operating Temperature Limit: 250°F (121°C) Greenguard Certified
Maximum Air Velocity: 6,000 fpm (30.5 m/sec)

Linacoustic® R-300
Rigid Fiberglass Plenum Liner Board with THERMAL PERFORMANCE SPECIFICATION
Reinforced Coating R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
in mm (hr•ft2•ºF)/Btu m2•ºC/W
ASTM C1071, Type II
1 25 4.3 0.76
1½ 38 6.3 1.11 ASTM G21 and G22
2 51 8.7 1.53 SMACNA Application Standards
3 76.2 13.0 2.34 for Duct Liners
4 101.6 17.4 3.13
NAIMA Fibrous Glass Duct Liner
Installation
SOUND-ABSORPTION COEFFICIENTS ASTM E84, FHC 25/50
Type A Mounting, Frequency (Hz)
NFPA 90A and 90B
in mm 125 250 500 1000 2000 4000 NRC
1 25 0.04 0.26 0.69 1.00 1.07 1.02 0.75 Conforms to ASHRAE 62
1½ 38 0.14 0.52 1.01 1.07 1.03 0.97 0.90 MEA # 353-93-M
2 51 0.26 0.73 1.10 1.10 1.04 1.03 1.00
Linacoustic® R-300 is a rigid fiberglass board designed to line ducts 3 76.2 0.56 1.18 1.24 1.12 1.04 1.03 1.15 Canada: C GSB 51.10 and
in plenum spaces. The insulation has a glass mat airstream surface 4 101.6 0.81 1.30 1.26 1.12 1.04 1.05 1.20 CAN/ULC S102
treated with the antimicrobial Permacote coating.
Recycled Content:
Operating Temperature Limit: 250°F (121°C) Refer to JM.com
Maximum Air Velocity: 6,000 fpm (30.5 m/sec) Greenguard Certified

3
Spiracoustic Plus® System
Fiberglass Liner with Reinforced Coating for
Spiral Metal Ducts
THERMAL PERFORMANCE SPECIFICATION
R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
in mm (hr•ft2•ºF)/Btu m2•ºC/W
ASTM C1071 Air Erosion Test /
1 25 4.3 0.76
UL 181
1½ 38 6.4 1.13
2 51 8.4 1.48 ASTM G21 and G22
ASTM E84, FHC 25/50
NFPA 90A and 90B
SOUND-ABSORPTION COEFFICIENTS Conforms to ASHRAE 62
Type A Mounting, Frequency (Hz) ULC S102
in mm 125 250 500 1000 2000 4000 NRC
1 25 0.05 0.21 0.71 1.01 1.07 1.09 0.75
1½ 38 0.10 0.39 1.02 1.08 1.04 1.00 0.85 Recycled Content:
Spiracoustic Plus® is a fiberglass insulation designed to line spiral ducts. 2 51 0.17 0.63 1.10 1.05 1.09 1.06 0.95 Refer to JM.com
It has factory-made, evenly spaced kerfs to allow the material to easily Greenguard Certified
conform to the inside diameter of spiral air ducts. The airstream surface
and transverse edges are protected with JM’s factory-applied Permacote
coating. Spiracoustic Plus can save time and reduce weight when
compared to some double-wall systems.
Operating Temperature Limit: 250°F (121°C)
Maximum Air Velocity: 6,000 fpm (30.5 m/sec)

Spiral SG®
Fiberglass Double-Wall Insulation THERMAL PERFORMANCE SPECIFICATION
K-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
Type PCF KG/M3 Btu•in/(hr•ft2•°F) W/M•°C
ASTM E84, FHC 25/50
75 0.75 12 0.30 0.043
85 0.85 14 0.27 0.039 NFPA 90A and 90B
100 1.04 17 0.26 0.037 CAN/ULC S102
125 1.20 19 0.25 0.036
UL 723
150 1.56 25 0.24 0.035

Recycled Content:
SOUND-ABSORPTION COEFFICIENTS
Type A Mounting, Frequency (Hz) Refer to JM.com
Greenguard Certified
Type in mm 125 250 500 1000 2000 4000 NRC
85 1 25 0.11 0.31 0.60 0.80 0.90 0.93 0.65
85 2 51 0.16 0.60 0.92 0.98 0.97 1.01 0.85
Spiral SG® is a fiberglass insulation designed for double-wall 100 1 25 0.09 0.30 0.60 0.77 0.89 0.93 0.65
applications. The insulation comes in a variety of thicknesses to help 100 2 51 0.18 0.64 0.99 1.02 1.01 1.04 0.90
optimize thermal and acoustical performance. It is made from rotary- 150 1 25 0.10 0.28 0.62 0.84 0.95 0.97 0.65
process glass fibers bonded with a thermosetting resin, improving 150 2 51 0.22 0.71 1.03 1.08 1.05 1.02 0.95
tensile strength and flexibility, and making it resistant to damage during
installation.
Operating Temperature Limit: 350°F (177°C)

LinaTex®
Textile Fiber Duct Liner THERMAL PERFORMANCE SPECIFICATION
R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
Type in mm (hr•ft2•ºF)/Btu m2•ºC/W
ASTM C1071, Type I, Flexible
300 ½ 13 2.6 0.45
300 1 25 4.2 0.74 ASTM G21 and G22
200 ½ 13 2.4 0.42 ASTM D5116-State of Washington
150 1 25 3.7 0.65
150 1½ 38 5.5 0.97 SMACNA Application Standards for
Duct Liners
NAIMA Fibrous Glass Duct Liner
SOUND-ABSORPTION COEFFICIENTS Installation
Type A Mounting, Frequency (Hz) ASTM E84, FHC 25/50
Type in mm 125 250 500 1000 2000 4000 NRC
NFPA 90A and 90B
300 ½ 13 0.03 0.14 0.30 0.55 0.72 0.84 0.45
300 1 25 0.08 0.27 0.62 0.86 0.92 0.91 0.65 Conforms to ASHRAE 62
LinaTex® is a textile fiber duct liner specifically designed for 200 ½ 13 0.06 0.13 0.28 0.52 0.71 0.74 0.40 Canada: C GSB 51-GP-11M and
lining sheet metal ducts in HVAC systems. The airstream surface 150 1 25 0.09 0.24 0.50 0.70 0.86 0.87 0.60 CAN/ULC S102
is protected with a high-density glass mat that can withstand 150 1½ 38 0.18 0.37 0.68 0.90 1.02 0.93 0.75
exposure to air velocities up to 5,000 fpm (25.4 m/sec). Recycled Content:
Operating Temperature Limit: 250°F (121°C) Refer to JM.com
Maximum Air Velocity: 5,000 fpm (25.4 m/sec)

4
DUCT BOARD INSULATION

SuperDuct® RC System
Fiberglass Duct Board with a Coated Glassmat
Airstream Surface
THERMAL PERFORMANCE SPECIFICATION
R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
in mm Type (hr•ft2•ºF)/Btu m2•ºC/W
UL 181, Class 1 Rigid Air Duct
1 25 475 4.3 0.76
Listed
1½ 38 800 6.5 1.15
2 51 800 8.7 1.53 Conforms to ASHRAE 62
ASTM G21 and G22
Canada: C GSB 51.10
SOUND-ABSORPTION COEFFICIENTS CAN/ULC-S110M
Type A Mounting, Frequency (Hz) MEA# 237-86-M
Type in mm 125 250 500 1000 2000 4000 NRC ASTM E84, FHC 25/50
475 1 25 0.04 0.27 0.71 0.96 1.03 0.99 0.75
SuperDuct RC is an FSK-faced fiberglass duct board insulation designed to be
®
800 1½ 38 0.11 0.45 0.96 1.07 1.06 1.00 0.90 NFPA 90A and 90B
fabricated into rectangular ducts. Each board comes with a male or female shiplap 800 2 51 0.14 0.81 1.10 1.07 1.03 1.01 1.00
to help make the fabrication process more efficient and accurate. The insulation Recycled Content:
itself has a glass mat airstream surface that is coated with the antimicrobial Refer to JM.com
Permacote coating to improve durability and offer resistance to microbial growth. Greenguard Certified
Operating Temperature Limit: 250°F (121°C)
Maximum Air Velocity: 6,000 fpm (30.5 m/sec)

Mat-Faced Micro-Aire®
Fiberglass Duct Board with a Glassmat
Airstream Surface
THERMAL PERFORMANCE SPECIFICATION
R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
in mm Type (hr•ft2•ºF)/Btu m2•ºC/W
UL 181, Class 1 Rigid Air Duct
1 25 475 4.3 0.76
Listed
1½ 38 800 6.5 1.15
2 51 800 8.7 1.53 ASTM G21 and G22
Conforms to ASHRAE 62
ICC Compliant
SOUND-ABSORPTION COEFFICIENTS MEA# 237-86-M
Type A Mounting, Frequency (Hz) ASTM E84, FHC 25/50
Type in mm 125 250 500 1000 2000 4000 NRC
475 1 25 0.07 0.25 0.63 0.90 0.97 1.00 0.70 NFPA 90A and 90B
800 1½ 38 0.10 0.42 0.91 1.04 1.04 1.04 0.85
Mat-Faced Micro-Aire® is an FSK-faced fiberglass duct board insulation 800 2 51 0.17 0.63 1.10 1.05 1.04 1.06 0.95 Recycled Content:
designed to be fabricated into rectangular ducts. The insulation features
a glass mat airstream surface and male and female shiplaps to improve Refer to JM.com
durability and efficiency during the fabrication process.
Operating Temperature Limit: 250°F (121°C)
Maximum Air Velocity: 5,000 fpm (25.4 m/sec)

Micro-Aire® LP
Fiberglass Duct System for Manufactured
and Modular Housing
THERMAL PERFORMANCE SPECIFICATION
R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
in mm (hr•ft2•°F)/Btu m2•°C/W
13/16
UL 181 Class 1 Rigid Air Duct Listed
20 3.50 0.62
ICC Compliant
MEA# 237-86-M
SOUND-ABSORPTION COEFFICIENTS Universal Building Code (UBC)
Type A Mounting, Frequency (Hz) International Mechanical Code
Type in mm 125 250 500 1000 2000 4000 NRC (IMC)
LP 13/16 20 0.07 0.23 0.49 0.79 0.94 1.03 0.60 Canada: CGSB 51.10-92 and CAN/
ULC-S110M
Micro-Aire® LP (Low Pressure) is an FSK-faced fiberglass duct board, ICC Compliant
designed to be fabricated into ducts for modular housing. Micro-Aire ASTM E84, FHC 25/50
LP offers improved thermal and acoustical control for systems that NFPA 90A and 90B
operate within relatively low air velocities (2,000 fpm).
Operating Temperature Limit: 250°F (121°C) Recycled Content:
Maximum Air Velocity: 2000 fpm (10.2 m/sec.) Refer to JM.com

5
Diffuser Board
Fiberglass Insulation Board

THERMAL PERFORMANCE SPECIFICATION

R-Value @ 75˚F (24˚C) Mean Temp.
COMPLIANCE
in mm (hr•ft2•˚F)/Btu m2•˚C/W
1 25 4.3 0.76 ASTM E84, FHC 25/50
1 3/8 34 6.0 1.04 UL 723
ASTM C1071
ASTM C411
SOUND-ABSORPTION COEFFICIENTS
Type A Mounting, Frequency (Hz) Recycled Content:
in mm 125 250 500 1000 2000 4000 NRC Refer to JM.com
1 25 0.05 0.20 0.68 0.92 0.94 1.03 0.70
1 3/8 34 0.09 0.32 0.86 0.98 0.97 1.00 0.80
Diffuser Board is a 4pcf density fiberglass board insulation designed to
insulate air diffusers and register boxes. The glass mat airstream surface
provides a smooth interior that offers minimal resistance to airflow.
Operating Temperature Limit: 250°F (121°C)
Maximum Air Velocity: 2,000 fpm (10.2 m/sec)

EXTERNAL DUCT INSULATION

Microlite® FSK Duct Wrap THERMAL PERFORMANCE

Formaldehyde-free™ Fiberglass Duct Wrap R-Value @ 75˚F (24˚C) Mean Temp. SPECIFICATION
INSTALLED
Type in mm (hr•ft2•ºF)/Btu m2•ºC/W
COMPLIANCE
75 11/2 38 4.2 0.74 ASTM C553
75 2 51 5.6 0.99 • Type II – Type 75, 100 and 150
75 2 1/5 56 6.0 1.08 • Type III – Type 150
75 3 76 8.3 1.46
ASTM C1290
75 4 2/5 112 12.0 2.16
100 1
1 /2 38 4.5 0.79 ASTM C1136, Type II
100 2 51 6.0 1.06 • Grade I – Type 75 Faced
1
150 1 /2 38 4.7 0.83 • Grade II – Type 100 Faced
150 2 51 6.3 1.11 • Grade III – Type 150 Faced
OUT OF PACKAGE ASTM E84, FHC 25/50 – FSK Facing
Type in mm (hr•ft2•ºF)/Btu m2•ºC/W NFPA 90A and 90B
75 11/2 38 5.2 0.92 ASTM C1136, Type II – FSK Facing
Microlite® FSK is a Formaldehyde-free™ fiberglass duct wrap that 75 2 51 6.9 1.22
75 2 1/5 56 7.5 1.33 MEA # 40-75-M
comes with an FSK vapor barrier facing. Microlite FSK is designed to
wrap rectangular and spiral ducts, offering improved thermal control. 75 3 76 10.3 1.81 Canada: C GSB 51-GP-11M and
75 4 2/5 112 15.0 2.66 CAN/ULC S102
Operating Temperature Limit: 250°F (121°C) 100 11/2 38 5.6 0.99
100 2 51 7.4 1.30 Recycled Content:
150 11/2 38 6.0 1.06 Refer to JM.com
150 2 51 8.0 1.41 Greenguard Gold Certified

Microlite® Black PSK and

White PSK Duct Wrap THERMAL PERFORMANCE SPECIFICATION
R-Value @ 75˚F (24˚C) Mean Temp.
Formaldehyde-free™ Fiberglass Duct Wrap COMPLIANCE
INSTALLED
Type in mm (hr•ft2•ºF)/Btu m2•ºC/W ASTM C553
75 11/2 38 4.2 0.74 • Type II – Type 75, 100 and 150
75 2 51 5.6 0.99 • Type III – Type 150
75 2 1/5 56 6.0 1.08 ASTM C1290*
75 3 76 8.3 1.46 *Facing provided free of print for aesthetic purposes
100 11/2 38 4.5 0.79
100 2 51 6.0 1.06 ASTM C1136, Type II
150 11/2 38 4.7 0.83 • Grade I – Type 75 Faced
150 2 51 6.3 1.11 • Grade II – Type 100 Faced
• Grade III – Type 150 Faced
OUT OF PACKAGE
Type in mm (hr•ft2•ºF)/Btu m2•ºC/W ASTM E84, FHC 25/50 – FSK Facing
75 11/2 38 5.2 0.92 NFPA 90A and 90B
75 2 51 6.9 1.22 ASTM C1136, Type II – FSK Facing
Microlite® PSK is a Formaldehyde-free™ fiberglass duct wrap that comes 75 2 1/5 56 7.5 1.33 MEA # 40-75-M
with a white or a black PSK vapor-barrier facing. The facing is offered 75 3 76 10.3 1.81
100 11/2 38 5.6 0.99 Canada: C GSB 51-GP-11M and CAN/
without print for aesthetic purposes and is designed to be used in exposed ULC S102
100 2 51 7.4 1.30
applications. Microlite PSK is designed to wrap rectangular and spiral ducts, 150 11/2 38 6.0 1.06
offering improved thermal control and aesthetic appeal. Recycled Content:
150 2 51 8.0 1.41
Refer to JM.com
Operating Temperature Limit: 250°F (121°C) Greenguard Gold Certified
Matching PSK Tape available, see accessories
6
Microlite® Standard Duct Wrap THERMAL PERFORMANCE SPECIFICATION
Fiberglass Duct Wrap Insulation R-Value @ 75˚F (24˚C) Mean Temp. COMPLIANCE
Unfaced Flame-Attenuated Duct Wrap ASTM C1290
Thickness Width Length R-values (hr•ft2•˚F)/Btu • Type I and Type II
Type in in ft Out of Package Installed ASTM C553
60 1 36 150 3.3 2.7 • Unfaced, Type I and Type II
1 72 150 3.3 2.7
11/2 48 100 5.0 4.0 ASTM C1139
• Type I and Type II
2 48 100 6.7 5.4
3 48 50 10.0 8.0 ASTM E84, FCH 25/50
75 1 48 100 3.6 2.9 NFPA 90A & 90B
11/2 48 100 5.3 4.3 Can/ULC S102-1188
3 48 50 10.7 8.7
Vinyl Duct Wrap
Thickness Width Length R-values (hr•ft2•˚F)/Btu
Microlite Standard Duct Wrap is a lightweight, highly resilient,
® Type in in ft Out of Package Installed
blanket-type, thermal and acoustical insulation made from flame- 60 11/2 48 100 4.8 3.9
attenuated glass fibers bonded with a thermosetting phenolic resin. 2 48 75 6.5 5.2

Operating Temperature Limit:

Unfaced: 350°F (177°C)
Faced: 250°F (121°C)

800 Series Spin-Glas® THERMAL PERFORMANCE SPECIFICATION

Fiberglass Duct and Equipment Insulation K-Value @ 75˚F (24˚C) Mean Temp.
COMPLIANCE
Type in mm Btu•in/(hr•ft2•°F) m2•ºC/W
812 1½–4 38–102 0.24 0.035 ASTM C612, Type 1A and 1B
813 1½–4 38–102 0.23 0.033 • (813, 814, 815, 817)
814 1–4 25–102 0.23 0.033 ASTM C533, Type III
815 1–2½ 25–64 0.22 0.032 • (812 plain material only)
817 1–2 25–51 0.22 0.032 ASTM C1136
• Type I – AP Facing
SOUND-ABSORPTION COEFFICIENTS • Type II – AP and FSK Facing
Type A Mounting, Frequency (Hz) ASTM E84, FHC 25/50; UL 723;
NFPA 255
Type in mm 125 250 500 1000 2000 4000 NRC
812 1 25 0.07 0.24 0.63 0.87 1.00 1.02 0.70 NFPA 90A and 90B
812 2 51 0.24 0.68 1.10 1.13 1.10 1.07 1.00 NRC 1.36; ASTM C795
813 1 25 0.08 0.27 0.69 0.95 1.05 1.02 0.75 MIL-DTL-24244
813 2 51 0.19 0.88 1.15 1.14 1.10 1.07 1.05 MIL-DTL-32585
814 1 25 0.06 0.29 0.75 0.99 1.04 1.02 0.75 MIL-I-22023
800 Series Spin-Glas® board insulation can be used in plain or faced
814 2 51 0.24 1.00 1.11 1.08 1.06 1.05 1.05 • Type I & II, Class 4 = 812
form to insulate heating ducts and equipment. 800 Series Spin-Glas 815 1 25 0.03 0.32 0.80 1.04 1.05 1.05 0.80 • Type I & II, Class 6 = 814
insulation is ideal for commercial and industrial heating, air 815 2 51 0.27 0.91 1.11 1.09 1.09 1.09 1.05 HH-I-558C, Form B, Type I, Class 7
conditioning, and power and process equipment. 817 1 25 0.10 0.35 0.85 1.04 1.05 1.03 0.80 • (812, 813, 814, 815)
Operating Temperature Limit: 817 2 51 0.38 0.93 1.10 1.07 1.07 1.07 1.05 Canada: CGSB 51-GP-10M and
Unfaced: 450°F (232°C) CAN/ULC S102-M88
Faced: faced side 150°F (66°C)

ACCESSORIES

Microlite® White & Black PSK Seaming Tape

Duct Wrap Seaming Tape

GENERAL INFORMATION
Standard UOM Metric UOM
White Black White Black Test Method
Thickness (w/o Liner) 8.8 mils 7.8 mils 0.224 mm 0.198 mm ASTM D-1000
Backing Thickness 7.0 mils 6.0 mils 0.178 mm 0.152 mm ASTM D-1000
Adhesion to Steel 50 oz/in* 36 oz/in* 5.47 N/cm 3.94 N/cm PSTC-101
Tensile Strength 24 lb/in 27 lb/in 42.03 N/cm 47.28 N/cm ASTM D-3759
Elongation 4% 4% 4% 4% ASTM D-3759

The Microlite PSK Duct Wrap Seaming Tape is designed to provide a Operating Temperature -20 to 260 °F -20 to 260 °F -29 to 126 °C -29 to 126 °C
vapor-barrier seal on JM’s PSK-faced Microlite duct insulations. The tape
is 96 MM wide and is offered in white or black to match the two color
offerings (white and black) of our PSK-faced microlite duct insulations.

7
SuperSeal® Coating Products GENERAL INFORMATION
SuperSeal® HV and SuperSeal® Edge Treatment
SuperSeal Shipping Approximate Shelf Life at Tack-Free Time
Product Unit Coverage* 40-95°F (4-35°C) (Approx.)
HV** 1 carton; 4 pails Usage-dependent 12 months 2 hours
1 gal. (3.8 l)
Edge Treatment 1 pail; 1700 sq. ft. 18 months 1 hour
5 gal. (18.9 l) (158 m2)

1 carton; 4 pails 1350 sq. ft. 18 months 1 hour

1 gal. (3.8 l) (125 m2)

* C
 overage estimates are based on minimum application weight to ensure product performance; actual application requirements may
be higher, depending upon the surface and application method.

** HV product applies grey and dries black.

SuperSeal® Coatings are air-dry derivatives of Permacote. SuperSeal
HV is designed for spot or edge repair where extra fill or adhesion
is required. SuperSeal Edge Treatment is intended for high-volume
shop applications, and it can be applied with a brush or sprayed. It
is ideal for repairing cuts or damage to the airstream surface.

Duct Knife
GENERAL INFORMATION
Duct knives are shipped in master cartons. Each master carton consists of 10 boxes of 10 knives each.
The minimum order quantity is one master carton (100 knives total).

Duct Insulation Knives are designed to smoothly cut fiberglass

insulation. The 6” blade slices cleanly through the fiberglass and
facing without snagging the material. The wooden handle is easy to
hold and curved to fit the hand.

Technical specifications as shown in this literature are intended to be used as general guidelines
only. Please refer to the Safety Data Sheet and product label prior to using these products. The
physical and chemical properties of the products listed herein represent typical, average values
obtained in accordance with accepted test methods and are subject to normal manufacturing
variations. They are supplied as a technical service and are subject to change without notice. Any
references to numerical flame spread or smoke developed ratings are not intended to reflect hazards
presented by these or any other materials under actual fire conditions. Check with your customer
717 17th St. service representative for current information.
Denver, CO 80202
800-654-3103 All Johns Manville products are sold subject to Johns Manville’s standard Terms and Conditions,
which includes a Limited Warranty and Limitation of Remedy. For a copy of the Johns Manville
www.jm.com/hvac standard Terms and Conditions or for information on other Johns Manville thermal insulation and
systems, visit www.jm.com/terms-conditions or call (800) 654-3103.
HVAC-472 05/13/19 (replaces 02/21/19)
© 2019 Johns Manville all rights reserved