Automatic Street Light Circuit Using LDR

Automatic Street Light Circuit using LDR
Abstract:
Automatic Street Light Circuit using LDR is presented here is based on the readily available
LDR, comparator IC LM393 and relay. The LDR is used as the light intensity detector while IC
LM393 used as comparator. In the absence of light, no light falls on the photo sensor. As a result
photo sensor stop conducting and Street light glows. However, when light falls on the photo
sensor photo sensor starts conducting and Street light stays off.
Buy Online " " Ready Kit, 100% Tested from below and get fastest delivery in India
www.smartxprokits.in/minikit/
Complete working video can be seen from
https://youtu.be/NvM_O79Z3DI
Follow us on Instagram
https://www.instagram.com/smartx2dx/
Application of the circuit:

Most of the LDR based circuits available in market use one or another kind of LDR which
increases the cost and also require complicated circuitry around it. But this LDR based circuit
uses readily available LDR as light detector. The functioning of this Automatic Street Light
Circuit using LDR is to detect interruption in light and automatically activate the Street light in
absence of light. Street light glows continuously indicating the absence of light till light falls on
the LDR.
Why this particular circuit:

LDR used here as a light detector. The variation in intensity of light wanted can be easily done
by interrupting light using hand palm. The circuit operates normally over a DC voltage of 5V
which can be obtained by DC supply cable.
Explained working of circuit:

The basic idea behind the circuit operation is to turn ON Street light in absence of light. The
LDR is needed for this purpose. LDR is photoelectric device as it converts light energy to
electric energy. Here, Automatic Street Light Circuit using LDR works as light detector while
LDR working as light sensor that glows street light. IC LM393 is used as comparator. LDR
output is connected as input to comparator. Pin no. 4 of LM393 is pulled towards ground. Relay
is used as a switch. When relay is activated, normally closed contact becomes open and normally
open contact becomes closed. In normal condition, light falls on LDR and street light stays off.
Now consider second scenario when light irrupts, the street light glows in the absence of light.
How to build:
First of all read the given manual thoroughly and study the circuit given in the figure. Also have
look at PCB and components supplied along with the kit. Each component has to be soldered in
its position on PCB.
Identification of resistors is done by color coding. The color band on each resistor corresponds to
its exact value.
There are different methods in which values are defined on capacitors. But usually values are
specified numerically on them.
Can you make out the whole working of circuit and are you able to identify each component
separately as to where each of them has to be placed?
If yes only then proceed further to actually mounting and soldering the parts.
Not ICs but their sockets are to be soldered on PCB. This is to make mounting and dismounting
of ICs easy while troubleshooting.
Start from left most corner of PCB and solder the components one by one on their correct
position on PCB.
Before soldering any component see that you have placed it at its right position and with correct
polarity. Give due attention to diodes and electrolytic capacitors as they are polarity dependent.
Do the soldering of other components in the same way while keeping in mind that components
with long and sensitive leads like capacitors and transistors are soldered last.
Testing the kit:

After assembling and soldering of components on PCB, connect external DC power source of
5V.
For testing purpose manually hold hand palm over LDR. LED glows in this case.
Now set the desired intensity at which you want detection of light. This can be done by changing
the resistive value of R2 variable resistor.
Install the unit at ceiling of room.
ICs used here:

The only IC used here is LM393
It is dual differential comparator IC.
This 8 pin IC is popular and commonly used IC
Part List:
Semiconductors
U1 - LM393
https://smartxprokits.in/product/lm393/
Base - 8 pin
https://smartxprokits.in/product/8-pin-dip-ic-socket-base-adaptor/
Resistors(all ¼ watt +/-5% carbon unless stated otherwise)
R2 - 10k Ohm(variable)
https://smartxprokits.in/product/10k-multiturn-potentiometer/
R3 - 1k Ohm
https://smartxprokits.in/product/1k-resistor-1-4-watt/
R4 - 1k Ohm
R5 - 10k Ohm
R6 - 10k Ohm
Capacitor C1 - 1uF
Miscellaneous
D4: - LDR
https://smartxprokits.in/product/843/
D1: - Red LED
https://smartxprokits.in/product/3mm-red-led/
D2: - Green LED
https://smartxprokits.in/product/3mm-green-led/
5 V USB Cable
https://smartxprokits.in/product/micro-usb-cable/
PCB
LED
https://smartxprokits.in/product/5mm-white-led/
Relay
https://smartxprokits.in/product/5v-10a-pcb-mount-relay-spdt/
LM393

Automatic Street Light Circuit Using LDR

Uploaded by

Copyright:

Available Formats

Automatic Street Light Circuit Using LDR

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Automatic Street Light Circuit Using LDR

Uploaded by

Copyright:

Available Formats

Automatic Street Light Circuit using LDR

Application of the circuit:

Why this particular circuit:

Explained working of circuit:

Testing the kit:

Install the unit at ceiling of room.

ICs used here:

It is dual differential comparator IC.

This 8 pin IC is popular and commonly used IC

Resistors(all ¼ watt +/-5% carbon unless stated otherwise)

D1: - Red LED

D2: - Green LED

You might also like