Sfcxx120Gexd - SFP Dual Fibre CWDM: Itu CWDM / 120Km / Gigabit Ethernet
Sfcxx120Gexd - SFP Dual Fibre CWDM: Itu CWDM / 120Km / Gigabit Ethernet
Sfcxx120Gexd - SFP Dual Fibre CWDM: Itu CWDM / 120Km / Gigabit Ethernet
SFCxx120GExD.docx
For your product safety, please read the following information carefully before any manipulation of the transceiver:
ESD
This transceiver is specified as ESD threshold 1kV for SFI pins and 2kV for all others electrical input pins, tested per MIL-STD-883G, Method 3015.4 /JESD22-
A114-A (HBM). However, normal ESD precautions are still required during the handling of this module.
LASER SAFETY
This is a Class1 Laser Product according to IEC 60825-1:2007. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated (June 24, 2007).
The optical ports of the module need to be terminated with an optical connector or with a dust plug in order to avoid contamination.
1. Overview
SFCxx120GExD is a high performance transceiver module for Gigabit Ethernet data links over a singlemode fibre pair. The
maximum reach is 120km, for a 32dB end of life (EOL) power budget. The emitter is a CWDM DFB laser, the receiver an APD
1
photodiode.
This transceiver module is compliant with the Small Form-factor Pluggable (SFP) Multisource Agreement (MSA) and hot
pluggable. Always contact Skylane Optics commercial agents for compatibility with different equipment platforms.
2. Features
• SFP Multi-Source Agreement compliant [INF-8074]
• Hot pluggable SFP footprint
• Serial ID functionality supported according to [SFF-8472]
• Class 1 laser safety standard IEC 60825 compliant
• Dual LC connector
• CWDM DFB transmitter
• 120km point-to-point transmission on single mode fibre
• 1x Fibre Channel compatible
• Gigabit Ethernet compatible
• Operating temperature range 0°C to 70°C or -20°C to 85°C Figure 1. SFP Dual Fiber ITU CWDM
• Low power dissipation (<1W) (non-binding illustration)
• Digital diagnostics monitoring (DDM)
3. Applications
• FTTx
• Gigabit Ethernet
• Storage
4. Optical Interface
Output Optical Optical Receiver Optical Receiver
Wavelength Power Budget2
P/N Power2 Sensitivity3 Overload4
[nm] [dB]
[dBm] [dBm] [dBm]
SFCxx120GExD ITU CWDM 0 to 5 ≤ -32 -8 ≥ 32
(47 to 61)
1. Distance is estimated assuming typical optical losses after decent quality fiber deployment; Only optical budget value is guaranteed.
2. EOL, over operating temperature range
3. Measured at 1.25Gbps, PRBS BER 27-1, ER=9dB, BER≤10-12
4. The optical input to the receiver should not exceed this value. Transmitters must never be directly connected to receivers (optical loop back) before ensuring that proper optical
attenuation is used.
5. Technical Parameters
5.1. Recommended Operating Conditions
Parameter Min Typ Max Units Notes
Storage temperature -40 85 °C
Operating Case Temperature -20 85 °C For SFCxx120GE1D
Operating Case Temperature 0 70 °C For SFCxx120GE0D
Relative Humidity 5 95 % Non condensing
Power Supply Voltage 3.15 3.3 3.45 V
Power Supply Current 300 mA
VeeT 20
1 VeeT TD- 19
2 Tx_Fault TD+ 18
3 Tx_Disable VeeT 17
4 SDA VccT 16
Towards BEZEL ← 5 SCL VccR 15 → Towards ASIC
6 MOD_ABS VeeR 14
7 RS0 RD+ 13
8 Rx_LOS RD- 12
9 RS1 VeeR 11
10 VeeR
8. EEPROM
0 0
Alarm and Warning
Thresholds (56 bytes)
Serial ID Defined by
55
SFP MSA (96 bytes)
Cal Constants
(40 bytes)
95 95
Real Time Diagnostic
Vendor Specifics Interface (24 bytes)
(32 bytes)
119
Vendor Specifics (8 bytes)
127 127
User writable Eeprom
Reserved (120 bytes)
(128 bytes)
247
255 Vendor Specifics (8 bytes)
255
A0h A2h
9. Ordering Information
Revision Description
A Initial release
Performing
Smartly