Scribd
Upload
83 views1 page

RTB 442

This document summarizes the technical specifications of Ronass Epoxy Coating RTB-442, a two-component, quick-drying epoxy primer. It adheres well, has excellent chemical and mechanical resistance, and protects against corrosion. It can be used as a shop primer, first coating, or intermediate coating on steel and metal surfaces. It dries within a few hours and fully cures within 7 days, and can be coated with various topcoats like alkyds, chlorinated rubbers, epoxies, and polyurethanes. Proper surface preparation and an application process involving mixing the two components in a specified ratio is described.

Uploaded by

ahmsal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
83 views1 page

RTB 442

This document summarizes the technical specifications of Ronass Epoxy Coating RTB-442, a two-component, quick-drying epoxy primer. It adheres well, has excellent chemical and mechanical resistance, and protects against corrosion. It can be used as a shop primer, first coating, or intermediate coating on steel and metal surfaces. It dries within a few hours and fully cures within 7 days, and can be coated with various topcoats like alkyds, chlorinated rubbers, epoxies, and polyurethanes. Proper surface preparation and an application process involving mixing the two components in a specified ratio is described.

Uploaded by

ahmsal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

RONASS EPOXY COATING

RTB-442 (A&B COMPONENTS)

Special two-component, quick-drying epoxy primer with excellent adhesion, chemical and mechanical resistances, and anti-corrosive properties.
USES AND SUITABALE TOP-COATS
Recommended Uses Shop primer, first coating or intermediate coating in multi-layered coating systems for steel structures and metal
surfaces, or as a single coating system in maintenance operations.
Suitable Top-Coats Alkyd paints, chlorinated rubber coatings, epoxy coatings, acrylic paints and polyurethane systems.
CHEMICAL COMPOSITION
Type of Binder Epoxy – Polyamide Solid Content After Mixing 72 ± 1% By Weight
Number of Component(s) 2 Components 52 ± 2% By Volume
Curing Mechanism Chemical Reaction Flash Point 28°C (82°F)
PHYSICAL PROPERTIES
Finish / Colour Flat | Oxide Red (RAL-3009) and Squirrel Grey (RAL-7000)
Specific Gravity After 1.45 ± 0.05 gr/cm³
Mixing
APPLICATION DETAILS
Surface Preparation All oil, grease, dirt and other contaminants must be removed from the surface. Sandblast according to Swedish STD.
Sa 2 ½ or greater is highly recommended.
Mixing Ratio Component A: 100 Parts by weight | Component B: 15 Parts by weight
Mixing Instructions Mix component A thoroughly with a suitable mixer, then add component B slowly and mix well for 10 minutes. Keep
the mixture for 5 additional minutes prior to thinning down to allow for the pre-reaction time. Do not thin down each
component separately.
Pot Life 4 Hours at 25°C
Theoretical Consumption 140 gr/m² @ 50 Microns DFT
Paint Application Methods Airless Spray Air Spray Brush Roller
Nozzle Size 0.009" – 0.017" 1.80 mm --- ---
Pump Ratio 45:1 --- --- ---
Air Pressure 4 – 6 Bar 3 – 5 Bar --- ---
Thinning 5 – 10% T-445 10 – 15% T-445 3 – 5% T-445 3 – 5% T-445
Film Thickness Recommended Minimum Maximum
Wet Film Thickness (µm) 95 30 190
Dry Film Thickness (µm) 50 15 100
Drying Time Dust Free Time Tack Free Time Dry to Handle Fully Cured Recoating Time
Min. 16 Hours
10 – 15 Minutes 30 – 60 Minutes 2 – 3 Hours 7 Days
Max. 10 Days
*Drying time calculated at 25°C according to ASTM test method D-1640 for 100 µm WFT
Application Limits Relative Humidity Min. --- Max. 80%
Temperature Min. +5°C Max. +40°C
Substrate Temperature* Min. +5°C Max. +45°C
*Please note that the substrate temperature should be at least 5°C above the dew point
Recommendations Should the recoating interval have expired, please refer to the procedures outlined in the Ronass Instruction Leaflet.
Clean tools thoroughly before and immediately after use with cleaning solvent T-111 or T-445.
PACKING, STORAGE AND SAFETY
Packing Component A (Epoxy): 20 L | Component B (Hardener): 4 L
Storage Conditions To be stored in cool and dry conditions in original sealed containers.
Shelf Life At least 18 months after delivery.
Safety This product contains organic solvents and flammable materials. Keep away from sparks, fires, electrical cables and
equipment, direct sunshine and out of children’s reach.
Protect skin, eyes, and avoid prolonged breathing of solvent vapor during application. Use with adequate ventilation.

REVISION:2018

You might also like