Scribd
Upload
1K views2 pages

Voltage Regulator Using Op Amp and Transistor

The document describes a voltage regulator circuit that uses an operational amplifier, emitter follower transistor, and Zener diode. It provides better load regulation than a simple Zener diode and resistor circuit. The op amp acts as a comparator between the regulated input reference voltage from the Zener diode and the voltage from a potential divider connected to the output. It drives the transistor to keep the two voltages equal, stabilizing the output voltage even under changing loads. The output voltage is 0.7V less than the op amp output due to the transistor junction. Equations for the circuit voltages are derived.

Uploaded by

Hà Thuận
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
1K views2 pages

Voltage Regulator Using Op Amp and Transistor

The document describes a voltage regulator circuit that uses an operational amplifier, emitter follower transistor, and Zener diode. It provides better load regulation than a simple Zener diode and resistor circuit. The op amp acts as a comparator between the regulated input reference voltage from the Zener diode and the voltage from a potential divider connected to the output. It drives the transistor to keep the two voltages equal, stabilizing the output voltage even under changing loads. The output voltage is 0.7V less than the op amp output due to the transistor junction. Equations for the circuit voltages are derived.

Uploaded by

Hà Thuận
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Voltage Regulator using Op Amp and Transistor

A voltage regulator circuit using an op amp, emitter follower transistor, and Zener diode,
is simple to draw from memory if you understand the working principle. These types of
circuits provide better load regulation, than a simple Zener diode and resistor alone. In
addition, if you make R1 a variable resistor, then the output voltage could be varied for a
large range of voltages. For this op amp circuit, we use the operational amplifier as a
comparator, and the two voltage levels that we are comparing are the regulated input
reference, and final output. We should also remember that we use potential dividers (PD)
to get a sample of the input and output voltages. As you can see, the input side consists of
a Zener diode and resistor, and this arrangement is the same if you were to have a simple
Zener diode regulator circuit. The regulated output from the Zener diode and resistor
network feeds the non-inverting input of the op amp. Engineers usually call this a
reference voltage because it remains the same, even when the input voltage varies. The
Zener diode obviously determines this fixed reference voltage across it, which we call V Z.
The output voltage from the second PD consisting of R 1 and R2 feeds the inverting input
of the comparator. This voltage is V2, which we usually find using the simple PD formula.
The two input voltages subtract as (VZ – V2), and the result value is the output VO from the
op amp that drives a power transistor in emitter-follower configuration. Hence, we can
deduce the formula to be the following.
VO = A × (VZ – V2)
In this formula, A is the open loop gain of the operational amplifier, which is usually
100000 for a 741-type device.
The final output voltage VOUT is (VO – 0.7 V). As you can see, it is always 0.7 V less
because of the emitter-follower junctions.
Regulation Scenario
Let us say that the output voltage V OUT begins to fall because of the loading across it. Then
V2 across R2 also falls, and then the result of (V Z – V2) increases, and VO also increases,
making the transistor conduct more, thereby increasing the output voltage. As you can see,
the mechanism of this comparator circuit is such that it tries to make V Z approximately
equal to V2 all the time.

Equations and Formula


Here is a simple PD formula showing V2 in terms of R1 and R2.

Since the op amp tries to make V 2 and VZ the same by compensating the output, we can
write the following expression.

By substitution, we derive this expression for VZ.

Here, we rearrange for VOUT.

Here we try to simplify.

Here is the final expression for VOUT in terms of VZ and resistors R1 and R2.

You might also like