Scribd
Upload
40 views4 pages

Spread Footing Design Based On ACI 318-02: Input Data Design Summary

This document contains input data and analysis for designing a spread footing based on ACI 318-02 standards. It includes input values for column dimensions, material strengths, loads, soil properties, and other parameters. The analysis calculates design load cases and determines the required footing area and suggested footing dimensions to support the column. Punching shear is checked on a critical perimeter of the footing to size the footing depth. The design summary specifies a footing width of 3 feet, length of 3 feet, and thickness of 5 inches.

Uploaded by

HassanKhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
40 views4 pages

Spread Footing Design Based On ACI 318-02: Input Data Design Summary

This document contains input data and analysis for designing a spread footing based on ACI 318-02 standards. It includes input values for column dimensions, material strengths, loads, soil properties, and other parameters. The analysis calculates design load cases and determines the required footing area and suggested footing dimensions to support the column. Punching shear is checked on a critical perimeter of the footing to size the footing depth. The design summary specifies a footing width of 3 feet, length of 3 feet, and thickness of 5 inches.

Uploaded by

HassanKhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 4

PROJECT :

CLIENT :
JOB NO. :
Spread Footing Design Based on ACI 318-02
INPUT DATA
COLUMN WIDTH c1 =
COLUMN DEPTH c2 = DESIGN SUMMARY
BASE PLATE WIDTH b1 = FOOTING WIDTH
BASE PLATE DEPTH b2 = FOOTING LENGTH
FOOTING CONCRETE STRENGTH fc' = FOOTING THICKNESS
REBAR YIELD STRESS fy =
AXIAL DEAD LOAD PDL =
AXIAL LIVE LOAD PLL =
LATERAL LOAD (0=WIND, 1=SEISMIC) =
SEISMIC AXIAL LOAD PLAT =
SURCHARGE qs =
SOIL WEIGHT ws =
FOOTING EMBEDMENT DEPTH Df =
ALLOW SOIL PRESSURE Qa =

ANALYSIS
DESIGN LOADS (IBC 2000 SEC.1605.3.2 & ACI 318-02 SEC.9.2.1)
CASE 1: DL + LL P = 9.6575 k
CASE 2: DL + LL + E / 1.4 P = 14.30036 k
CASE 3: 0.9 DL + E / 1.4 P = 9.284607 k

Since the Space between bottom of the footing and surface will be occopied by soil and footing concrete an average unit w
the net pressure is

qe= 0 Psi 0 Ksi

A req= #DIV/0! Ft2

B=L= #DIV/0! Ft

The suggested footing dimensions are

Bsug=Lsug= Ft and Asug= 0 Ft2

For strenght design the upward pressure caused by factored colum load is

qu= #DIV/0! kips/ft2

The footing depth in square footing is usually determined by punching shear on critical perimeter abcd

let d= 19 in
bo= 76 in

The shear force acting on this perimeter ,being equal to the total upward pressure minas that acting within the perimeter

Vu1= -15.2923611111
PAGE :
DESIGN BY :
DATE : REVIEW BY :

DESIGN SUMMARY
FOOTING WIDTH B = 3.00 ft
FOOTING LENGTH L = 3.00 ft
FOOTING THICKNESS T = 5 in

1.2 DL + 1.6 LL Pu = 13.2 k


1.2 DL + 1.0 LL + 1.0 E Pu = 17 k
0.9 DL + 1.0 E Pu = 11 k

concrete an average unit weight of 125psf will be assumed.


cting within the perimeter abcd is

You might also like