Scribd
Upload
63 views

Task Sheet - UC 1: //192.168.1.56 //server

This document provides instructions for connecting network resources and performing backup and restore tasks. It includes: 1) Commands to locate and connect to shared network resources on another computer using the IP address or computer name in Run Command or the address bar. 2) Steps for making a crossover or straight-through cable, assigning IP addresses, configuring computer names and workgroups, and adjusting firewall and sharing settings to enable connectivity between computers. 3) Instructions for performing disk cleanup and defragmentation, backing up files to a designated location, deleting the backup files, and restoring files either from the backup drive or using restore utilities.

Uploaded by

Herwin Capiñanes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
63 views

Task Sheet - UC 1: //192.168.1.56 //server

This document provides instructions for connecting network resources and performing backup and restore tasks. It includes: 1) Commands to locate and connect to shared network resources on another computer using the IP address or computer name in Run Command or the address bar. 2) Steps for making a crossover or straight-through cable, assigning IP addresses, configuring computer names and workgroups, and adjusting firewall and sharing settings to enable connectivity between computers. 3) Instructions for performing disk cleanup and defragmentation, backing up files to a designated location, deleting the backup files, and restoring files either from the backup drive or using restore utilities.

Uploaded by

Herwin Capiñanes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

Task Sheet – UC 1 Command and procedure to connect network

resources
LO1 -

 Perform Assemble and Disassemble Use IP address, computer name, workgroup name to
component parts and list the parts, including locate
the capacity and brand name.
 Make an inventory list of the tools, equipment Open run command, type double back slash then
and materials used. type[IP address, computer name] of the server PC.
LO 2 – Ex. \\192.168.1.56 or \\server
 Create bootable disk – Windows 7 If the shared PC show double click the shared
 Configure BIOS resources to connect.
 Install Operating System
 Update Motherboard drivers Open address bar type double back slash then type[IP
LO 3 – address, computer name] of the server PC.
 Install MS office application Ex. \\192.168.1.56 or \\server
 Install Anti Virus If the shared PC show double click the shared
 Install Browser resources to connect.

LO 4 – Press winkey in the search engine type double back


 Make Straight Thru or Cross over cable slash then type[IP address, computer name] of the
 Assign IP address both Server and Client PC server PC.
 Configure Computer Name and Workgroup Ex. \\192.168.1.56 or \\server
Name
 Configure windows firewall settings, go to Note: This Unit of competency performed within 90
network and sharing center then turn on minutes only
network discovery, files and printer sharing,
and Turn Off password both client and server
PC. Task Sheet - UC 4
 Disable anti-virus software setting.
 Check the connectivity both server and client LO 1-
using (PING command) Perform disk defragment
Ex. Syntax PING 192.168.1.56 or PING Perform disk Clean-Up
Server Open My Documents then Create folder and put
Command atleast four files inside it.
IP address of the PC Go to Local disk D: Set Back-Up destination
you want to reach Perform Back-Up used your files created.
Space after the ping After back-up (Note: Make sure that your back-up files is
 Create folder put new files inside at least 4 correct and according to the standard ) Delete your back-
files and then shared the folder change up files.
permission to everyone. Perform Restore files- (Ways – Open drive D: then
double click back-up image or open back up and
LO 5 restore utility then click restore files button.
 Install printer Firmware in Server PC Verify if the restore files stay in the same location.
 Try Test Print – Open Notepad type any info Open my documents where your create files origin
 Shared Printer location.
 In client PC locate your Shared Printer and
Open Notepad then print. [observe below
command and procedure]

UC1- UC 4 Task Sheet WMA

You might also like