Power Supply, Ground & Circuit Elements: Section

ELECTRICAL & POWER CONTROL
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS

SECTION PG B
E
CONTENTS
PRECAUTION ............................................... 3 Wiring Diagram - BATTERY POWER SUPPLY F
FUSE No. 37 - .........................................................49
PRECAUTIONS ................................................... 3 Wiring Diagram - ACCESSORY POWER SUP-
cardiagn.com
Precaution for Supplemental Restraint System PLY - ........................................................................50 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Wiring Diagram - ACCESSORY POWER SUP-
SIONER" ................................................................... 3 PLY FUSE No. 18 - .................................................54
Precaution for Power Generation Voltage Variable Wiring Diagram - IGNITION POWER SUPPLY -
H
Control System .......................................................... 3 WITH MR16DDT - ...................................................55
Wiring Diagram - IGNITION POWER SUPPLY -
PREPARATION ............................................ 4 WITH MRA8DE - .....................................................67
Wiring Diagram - IGNITION POWER SUPPLY I
PREPARATION ................................................... 4
FUSE No. 2 - ...........................................................82
Special Service Tool ................................................. 4
Wiring Diagram - IGNITION POWER SUPPLY
Commercial Service Tool .......................................... 4
FUSE No. 3 - ...........................................................83 J
SYSTEM DESCRIPTION .............................. 5 Wiring Diagram - IGNITION POWER SUPPLY
FUSE No. 5 - ...........................................................84
ELECTRICAL UNITS LOCATION ....................... 5 Wiring Diagram - IGNITION POWER SUPPLY
K
Electrical Units Location ............................................ 5 FUSE No. 45 - .........................................................86
Wiring Diagram - IGNITION POWER SUPPLY
COMPONENT PARTS ........................................ 9 FUSE No. 51 - .........................................................87
Circuit Breaker (Built Into BCM) ................................ 9 Wiring Diagram - IGNITION POWER SUPPLY L
Harness Connector ................................................... 9 FUSE No. 52 - .........................................................88
Standardized Relay ................................................. 12 Wiring Diagram - IGNITION POWER SUPPLY
REAR WINDOW DEFOGGER RELAY- ..................89 PG
WIRING DIAGRAM ...................................... 15 Wiring Diagram - IGNITION POWER SUPPLY
POWER SUPPLY ROUTING CIRCUIT ..............15 STARTER CONTROL RELAY- ...............................90
Wiring Diagram - BATTERY POWER SUPPLY - GROUND ........................................................... 91 N
WITH MR16DDT - ................................................... 15 Ground Distribution ..................................................91
Wiring Diagram - BATTERY POWER SUPPLY -
WITH MRA8DE - ..................................................... 29 HARNESS ....................................................... 101 O
Wiring Diagram - BATTERY POWER SUPPLY Harness Layout ..................................................... 101
FUSE No. 8 - ........................................................... 43
Wiring Diagram - BATTERY POWER SUPPLY FUSE BLOCK - JUNCTION BOX (J/B) .......... 126
FUSE No. 26 - ......................................................... 44 Terminal Arrangement ........................................... 126 P
Wiring Diagram - BATTERY POWER SUPPLY
FUSE No. 30 - ......................................................... 45
FUSE, FUSIBLE LINK AND RELAY BOX ...... 127
Terminal Arrangement ........................................... 127
Wiring Diagram - BATTERY POWER SUPPLY
FUSE No. 33 (ECM RELAY) - ................................. 46 IPDM E/R (INTELLIGENT POWER DISTRI-
Wiring Diagram - BATTERY POWER SUPPLY BUTION MODULE ENGINE ROOM) .............. 130
FUSE No. 36 - ......................................................... 48 IPDM E/R Terminal Arrangement .......................... 130
Revision: December 2016 PG-1 2017 Sentra NAM

BASIC INSPECTION .................................. 131 BATTERY ......................................................... 140
Exploded View ...................................................... 140
BATTERY ........................................................ 131 Battery Disconnect ................................................ 140
How to Handle Battery ...........................................131 Removal and Installation (Battery) ........................ 141
Work Flow ..............................................................131
BATTERY TERMINAL WITH FUSIBLE LINK .. 142
INSPECTION AND ADJUSTMENT ................. 134 Exploded View ...................................................... 142
Removal and Installation ....................................... 142
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL .................................134 BATTERY CURRENT SENSOR ...................... 143
ADDITIONAL SERVICE WHEN REMOVING Exploded View ...................................................... 143
BATTERY NEGATIVE TERMINAL : Special Re- Removal and Installation ....................................... 143
pair Requirement ...................................................134
SERVICE DATA AND SPECIFICATIONS
FUSE INSPECTION ......................................... 135
(SDS) ......................................................... 144
How To Check .......................................................135
SERVICE DATA AND SPECIFICATIONS
FUSIBLE LINK INSPECTION .......................... 139
Fusible Link ...........................................................139
(SDS) ................................................................ 144
Battery ................................................................... 144
REMOVAL AND INSTALLATION .............. 140
cardiagn.com

PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000014525319
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, it is recommended that all mainte-
nance and repair be performed by an authorized NISSAN/INFINITI dealer. E
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see the SR section.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
cardiagn.com
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the H
Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I
battery or batteries, and wait at least three minutes before performing any service.
Precaution for Power Generation Voltage Variable Control System INFOID:0000000014525320
J
CAUTION:
For model with power generation voltage variable control system, the battery current sensor that is
installed to the battery cable at the negative terminal measures the charging/discharging current of K
the battery, and performs various controls. If the electrical component or the ground wire is connected
directly to the battery terminal, the current other than that being measured with the battery current
sensor is charging to or discharging from the battery. This condition causes the malfunction of the
L
control, and then the battery discharge may occur. Do not connect the electrical component or the
ground wire directly to the battery terminal.
PG

PREPARATION
< PREPARATION >
PREPARATION
PREPARATION
Special Service Tool INFOID:0000000014525321
The actual shape of the tools may differ from those illustrated here.
Tool number Description
(TechMate No.)
Tool name
— Tests batteries, starting and charging sys-
(—) Model GR8-1200 NI tems and charges batteries.
Multitasking battery and electrical di- For operating instructions, refer to diagnostic
agnostic station station instruction manual.
AWIIA1239ZZ
— Tests batteries and charging systems.

(—) Model EXP-800 NI For operations instructions, refer to diagnos-
Battery and electrical diagnostic ana- tic analyzer instruction manual.
cardiagn.com
lyzer
JSMIA0806ZZ
Commercial Service Tool INFOID:0000000014525322
Tool name Description

Power tool Loosening nuts, screws and bolts
PIIB1407E

ELECTRICAL UNITS LOCATION
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION A
Electrical Units Location INFOID:0000000014525323
B
ENGINE COMPARTMENT
C
cardiagn.com
G
PG
AAMIA5762GB

PASSENGER COMPARTMENT
cardiagn.com
AAMIA5763GB

cardiagn.com
G
PG
AAMIA5764GB

LUGGAGE COMPARTMENT
cardiagn.com
AAMIA5765GB

COMPONENT PARTS
COMPONENT PARTS
A
Circuit Breaker (Built Into BCM) INFOID:0000000014525324
For example, when current is 30A, the circuit is broken within 8 to 20 B

seconds.
A circuit breaker is used for the following systems:
• Power windows
• Power moonroof C
• Power lumbar
• Power seats
D
SBF284E E
Harness Connector INFOID:0000000014525325
HARNESS CONNECTOR (TAB-LOCKING TYPE) F

• The tab-locking type connectors help prevent accidental looseness or disconnection.
• The tab-locking type connectors are disconnected by pushing or lifting the locking tab(s). Refer to the figure
cardiagn.com
below. G
Refer to the next page for description of the slide-locking type connector.
CAUTION:
Do not pull the harness or wires when disconnecting the connector.
H
PG

COMPONENT PARTS
[Example]
cardiagn.com
SEL769DA
HARNESS CONNECTOR (SLIDE-LOCKING TYPE)

• A new style slide-locking type connector is used on certain systems and components, especially those
related to OBD.
• The slide-locking type connectors help prevent incomplete locking and accidental looseness or disconnec-
tion.
• The slide-locking type connectors are disconnected by pushing or pulling the slider. Refer to the figure
below.
CAUTION:
• Do not pull the harness or wires when disconnecting the connector.
• Be careful not to damage the connector support bracket when disconnecting the connector.

COMPONENT PARTS
[Example]
A
cardiagn.com
G
I
SEL769V
HARNESS CONNECTOR (LEVER LOCKING TYPE)

• Lever locking type harness connectors are used on certain control units and control modules such as ECM, J
ABS actuator and electric unit (control unit), etc.
• Lever locking type harness connectors are also used on super multiple junction (SMJ) connectors.
• Always confirm the lever is fully locked in place by moving the lever as far as it will go to ensure full connec- K
tion.
CAUTION:
L
PG

COMPONENT PARTS
• Always confirm the lever is fully released (loosened) before attempting to disconnect or connect
these connectors to avoid damage to the connector housing or terminals.
cardiagn.com
LKIA0670E
1. Control unit with single lever 2. Control unit with dual lever 3. SMJ connector
A. Fasten A. Lever A. Lever
B. Loosen B. Fasten B. Fasten
C. Lever C. Loosen C. Loosen
HARNESS CONNECTOR (DIRECT-CONNECT SRS COMPONENT TYPE)

• SRS direct-connect type harness connectors are used on certain SRS components such as air bag modules
and seat belt pre-tensioners.
• Always pull up to release black locking tab prior to removing connector from SRS components.
• Always push down to lock black locking tab after installing connector to SRS components. When locked, the
black locking tab is level with the connector housing.
CAUTION:
• Do not pull the harness or wires when removing connectors
from SRS components.
WHIA0103E
Standardized Relay INFOID:0000000014525326
NORMAL OPEN, NORMAL CLOSED AND MIXED TYPE RELAYS

COMPONENT PARTS
Relays can mainly be divided into three types: normal open, normal closed and mixed type relays.
A
SEL881H F
TYPE OF STANDARDIZED RELAYS
cardiagn.com
G
1M ···················· 1 Make 2M ···················· 2 Make
1T ···················· 1 Transfer 1M·1B ···················· 1 Make 1 Break
H
PG
SEL882H

COMPONENT PARTS
cardiagn.com
SEL188W

POWER SUPPLY ROUTING CIRCUIT
< WIRING DIAGRAM >
WIRING DIAGRAM A
Wiring Diagram - BATTERY POWER SUPPLY - WITH MR16DDT - INFOID:0000000015057396
B
cardiagn.com
G
PG
ABMWA4505GB

< WIRING DIAGRAM >
cardiagn.com
AAMWA2561GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
ABMWA4506GB

< WIRING DIAGRAM >
cardiagn.com
AAMWA2563GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5807GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5808GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5809GB

< WIRING DIAGRAM >
cardiagn.com
ABMIB1111GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
ABMIB1112GB

< WIRING DIAGRAM >
cardiagn.com
ABMIB1113GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
ABMIB1114GB

< WIRING DIAGRAM >
cardiagn.com
ABMIB1115GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
ABMIB1116GB

< WIRING DIAGRAM >
cardiagn.com
ABMIB1117GB

< WIRING DIAGRAM >
Wiring Diagram - BATTERY POWER SUPPLY - WITH MRA8DE - INFOID:0000000015057480
cardiagn.com
G
PG
AAMWA2564GB
P

< WIRING DIAGRAM >
cardiagn.com
AAMWA2565GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMWA2566GB

< WIRING DIAGRAM >
cardiagn.com
AAMWA2567GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5817GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5818GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5819GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5820GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5821GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5822GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5823GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5824GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5825GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5826GB

< WIRING DIAGRAM >
Wiring Diagram - BATTERY POWER SUPPLY FUSE No. 8 - INFOID:0000000015057565
cardiagn.com
G
PG
P
AAMIA5848GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5849GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
P
AAMIA5850GB

< WIRING DIAGRAM >
Wiring Diagram - BATTERY POWER SUPPLY FUSE No. 33 (ECM RELAY) -
INFOID:0000000015057567
cardiagn.com
AAMIA5851GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5852GB

< WIRING DIAGRAM >
cardiagn.com
ABMIB1118GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
P
AAMIA5854GB

< WIRING DIAGRAM >
Wiring Diagram - ACCESSORY POWER SUPPLY - INFOID:0000000015057481
cardiagn.com
AAMWA2559GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5804GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5805GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5806GB

< WIRING DIAGRAM >
Wiring Diagram - ACCESSORY POWER SUPPLY FUSE No. 18 - INFOID:0000000015057818
cardiagn.com
AAMIA5847GB

< WIRING DIAGRAM >
Wiring Diagram - IGNITION POWER SUPPLY - WITH MR16DDT - INFOID:0000000015057494
cardiagn.com
G
PG
AAMWA2568GB
P

< WIRING DIAGRAM >
cardiagn.com
AAMWA2569GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMWA2570GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5827GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5828GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5829GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5830GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5831GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5832GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5833GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5834GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5835GB

< WIRING DIAGRAM >
Wiring Diagram - IGNITION POWER SUPPLY - WITH MRA8DE - INFOID:0000000015057563
cardiagn.com
G
PG
P
AAMWA2571GB

< WIRING DIAGRAM >
cardiagn.com
AAMWA2572GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMWA2573GB

< WIRING DIAGRAM >
cardiagn.com
AAMWA2574GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5836GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5837GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5838GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5839GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5840GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5841GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5842GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5843GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5844GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5845GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5846GB

< WIRING DIAGRAM >
Wiring Diagram - IGNITION POWER SUPPLY FUSE No. 2 - INFOID:0000000015057819
cardiagn.com
AAMIA5855GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5856GB
P

< WIRING DIAGRAM >
cardiagn.com
AAMIA5857GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5858GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5859GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5860GB
P

< WIRING DIAGRAM >
cardiagn.com
AAMIA5861GB

< WIRING DIAGRAM >
Wiring Diagram - IGNITION POWER SUPPLY REAR WINDOW DEFOGGER RELAY-
INFOID:0000000015057824 A
cardiagn.com
G
PG
AAMIA5862GB

< WIRING DIAGRAM >
Wiring Diagram - IGNITION POWER SUPPLY STARTER CONTROL RELAY-
INFOID:0000000015057825
AAMIA5863GB
cardiagn.com

GROUND
< WIRING DIAGRAM >
GROUND
A
Ground Distribution INFOID:0000000014525330
BODY HARNESS B
cardiagn.com
G
PG
AAMIA5864GB

GROUND
< WIRING DIAGRAM >
cardiagn.com
AAMIA5865GB

GROUND
< WIRING DIAGRAM >
ENGINE ROOM HARNESS
A
cardiagn.com
G
PG
ABMIB1108GB
P

GROUND
< WIRING DIAGRAM >
cardiagn.com
ABMIB1109GB

GROUND
< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5868GB

GROUND
< WIRING DIAGRAM >
ENGINE CONTROL HARNESS
cardiagn.com
AAMIA5869GB

GROUND
< WIRING DIAGRAM >
MAIN HARNESS
A
cardiagn.com
G
PG
AAMIA5870GB
P

GROUND
< WIRING DIAGRAM >
cardiagn.com
AAMIA5871GB

GROUND
< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5872GB

GROUND
< WIRING DIAGRAM >
cardiagn.com
AAMIA5873GB

HARNESS
< WIRING DIAGRAM >
HARNESS
A
Harness Layout INFOID:0000000014525331
HOW TO READ HARNESS LAYOUT B

The following Harness Layouts use a map style grid to help locate
connectors on the drawings:
• Body Harness, ODS sub-Harness, and Side Radar Sub-harness C
• Engine Room Harness (MRA8DE)
• Engine Room Harness (MR16DDT)
• Engine Room Harness (Passenger Compartment)
• Engine Control Harness (MRA8DE M/T) D
• Engine Control Harness (MRA8DE CVT)
• Engine Control Harness (MR16DDT M/T)
• Engine Control Harness (MR16DDT CVT) E
• Main Harness
SEL252V
• Room Lamp Harness
To use the grid reference
F
1. Find the desired connector number on the connector list.
2. Find the grid reference.
cardiagn.com
3. On the drawing, find the crossing of the grid reference letter column and number row. G
4. Find the connector number in the crossing zone.
5. Follow the line (if used) to the connector.
OUTLINE H
PG
AAMIA5780GB

HARNESS
< WIRING DIAGRAM >
BODY HARNESS
cardiagn.com
AAMIA0621ZZ
: High-mounted stop lamp (Without rear

C1 B2 W/8 : To M7 F3 B46 B/2
spoiler)
A2 B3 W/4 : To E5 G4 B47 GR/3 : EVAP control system pressure sensor
: Fuel level sensor and fuel pump (Fuel
C1 B4 W/16 : To M5 D3 B48 GR/5
level sensor)
D3 B5 — : Body ground E3 B49 L/2 : Inside key antenna (Trunk room)

HARNESS
< WIRING DIAGRAM >
D4 B6 W/20 : To B93 D3 B50 GR/1 : Rear window defogger condenser
A
B2 B7 — : Body ground C1 B51 Y/2 : Front RH side air bag module
A2 B8 W/12 : To M8 B4 B52 Y/2 : Front side air bag satellite sensor LH
A2 B9 W/24 : To E13 E2 B53 Y/2 : Front side air bag satellite sensor RH B
C1 B10 W/32 : To M9 D4 B54 B/2 : Rear wheel sensor LH
A2 B11 W/24 : To M10 E3 B55 GR/2 : Rear wheel sensor RH
: BCM (Body control module) (Without C
C2 B12 W/3 : Heated seat LH A1 B57 B/15
Intelligent Key system)
D2 B13 W/3 : Heated seat RH F3 B58 W/2 : Trunk room lamp
D
F4 B14 BR/2 : Trunk opener request switch F4 B59 W/3 : Trunk lid opener assembly
B2 B15 Y/22 : Air bag diagnosis sensor unit D4 B60 W/12 : To B76
C3 B16 W/4 : Seat belt buckle switch LH C2 B61 W/5 : Power seat switch LH E
: EVAP canister vent control solenoid
F4 B17 B/2 E3 B62 B/1 : Rear window defogger
valve
C2 B18 Y/22 : Air bag diagnosis sensor unit F2 B63 B/1 : Rear window defogger F
C2 B19 — : Body ground G2 B64 — : Ground
cardiagn.com
C3 B20 W/10 : To D201 A2 B68 W/2 : To M98
: High-mounted stop lamp (With rear
G
B3 B21 W/4 : Front door switch LH F4 B71 W/4
spoiler)
: Front RH seat belt pre-tensioner
E2 B22 Y/2 A3 B73 B/24 : Joint connector-B01 H
(Shoulder belt)
C3 B23 O/2 : LH side curtain air bag module F4 B74 BR/2 : License plate lamp LH
: BCM (Body control module) (With
A1 B24 B/15 G4 B75 BR/2 : License plate lamp RH I
E5 B25 W/6 : Rear combination lamp LH D4 B76 W/12 : To B60
C3 B26 W/4 : Rear door switch LH E5 B77 G/16 : Joint connector-B02
J
D1 B28 W/4 : Front door switch RH G5 B79 L/2 : Outside key antenna (Rear bumper)
: Front LH seat belt pre-tensioner (Lap
F5 B29 B/8 : To B250 C3 B80 O/2
belt) K
F4 B30 B/6 : Rear view camera E2 B81 Y/2 : Rear side air bag satellite sensor RH
E1 B31 W/10 : To D301 C4 B82 Y/2 : Rear side air bag satellite sensor LH
C1 B32 W/4 : Seat belt buckle switch RH C1 B83 W/8 : To B300 L
: Front LH seat belt pre-tensioner : Front RH seat belt pre-tensioner (Lap
C3 B33 Y/2 D2 B84 O/2
(Shoulder belt) belt)
PG
F2 B34 — : Body ground B3 B89 B/3 : G sensor
E1 B35 O/2 : RH side curtain air bag module F5 B90 W/20 : Joint connector-B03
E4 B36 W/2 : Rear woofer LH C1 B92 W/24 : To M1 N
C3 B37 Y/2 : Front LH side air bag module D5 B93 W/20 : To B6
F3 B38 W/2 : Rear speaker RH Side radar sub-harness
G3 B39 W/2 : Rear woofer RH F5 B250 B/8 : To B29 O
E4 B40 W/2 : Rear speaker LH E5 B251 B/8 : Side radar LH
F2 B41 W/4 : Rear door switch RH G3 B252 B/8 : Side radar RH
P
G3 B42 W/6 : Rear combination lamp RH ODS sub-harness
E4 B43 BR/23 : BOSE® speaker amp. C2 B300 W/8 : To B83
F3 B44 BR/14 : BOSE speaker amp.

HARNESS
< WIRING DIAGRAM >
FRONT DOOR LH HARNESS
cardiagn.com
AAMIA0623ZZ
: Front door speaker LH (Without BOSE

D2 W/55 : To M13 D10 W/2
audio system)
: Main power window and door lock/unlock : Main power window and door lock/unlock
D5 W/16 D11 W/3
switch switch
D6 GR/2 : Outside key antenna (Driver side) D12 Y/2 : Front door satellite sensor LH
: Front door speaker LH (With BOSE audio
D7 W/12 : Door mirror LH D13 BR/2
system)
D8 G/6 : Front power window motor LH D15 B/2 : Front outside handle LH (Request switch)
D9 GR/6 : Front door lock assembly LH D21 W/4 : Blind spot warning indicator LH

HARNESS
< WIRING DIAGRAM >
FRONT DOOR RH HARNESS
A
cardiagn.com
G
I
AAMIA0624ZZ
D101 W/55 : To M74 D109 Y/2 : Front door satellite sensor RH

J
: Power window and door lock/unlock switch : Front door speaker RH (Without BOSE
D104 W/12 D110 W/2
RH audio system)
: Front door speaker RH (With BOSE audio
D105 G/6 : Front power window motor RH D111 BR/2 K
system)
D106 W/12 : Door mirror RH D114 W/4 : Blind spot warning indicator RH
D107 GR/6 : Front door lock actuator RH D115 B/2 : Front outside handle RH (Request switch) L
D108 GR/2 : Outside key antenna (Passenger side)
PG

HARNESS
< WIRING DIAGRAM >
REAR DOOR LH HARNESS
cardiagn.com
AAMIA0473ZZ
D201 W/10 : To B20 D204 G/6 : Rear power window motor LH

D202 GR/6 : Rear door lock actuator LH D207 BR/2 : Rear door speaker LH
D203 W/8 : Rear power window switch LH

HARNESS
< WIRING DIAGRAM >
REAR DOOR RH HARNESS
A
cardiagn.com
G
I
AAMIA0474ZZ
D301 W/10 : To B31 D304 G/6 : Rear power window motor RH

J
D302 GR/6 : Rear door lock actuator RH D309 BR/2 : Rear door speaker RH
D303 W/8 : Rear power window switch RH
K
PG

HARNESS
< WIRING DIAGRAM >
ENGINE ROOM HARNESS (WITH MRA8DE)
cardiagn.com
AAMIA0810ZZ
: IPDM E/R (Intelligent power distribution

D1 E1 GR/5 : Front wiper motor E2 E45 BR/12
module engine room)
B5 E8 B/2 : Front washer motor F2 E46 W/12
module engine room)
A3 E9 — : Body ground F2 E47 BR/8
module engine room)

HARNESS
< WIRING DIAGRAM >
D3 E10 BR/2 : Fusible link box (Battery) F2 E48 B/6
module engine room) A
D2 E11 GR/2 : Fusible link box (Battery) G3 E50 B/2 : Front combination lamp LH
G2 E15 — : Body ground B4 E51 B/2 : Front combination lamp RH
B
E2 E16 GR/32 : ECM A3 E52 GR/2 : Front wheel sensor RH
C4 E20 B/8 : Front combination lamp RH D3 E53 GR/4 : Cooling fan motor
G3 E21 B/8 : Front combination lamp LH E4 E57 B/1 : Horn (Low) C
E4 E23 Y/2 : Crash zone sensor C4 E58 BR/1 : Horn (High)
G4 E27 B/2 : Front fog lamp LH G1 E61 GR/2 : Front wheel sensor LH
D
B5 E28 B/2 : Front fog lamp RH F1 E62 B/24 : Joint connector-E04
C3 E30 L/4 : Daytime running light relay F1 E63 B/10 : Joint connector-E03
: ABS actuator and electric unit (Control E
C2 E33 B/38 G2 E64 B/48 : To F50
unit) (Without intelligent cruise control)
D5 E35 B/3 : Refrigerant pressure sensor B5 E65 BR/2 : Washer fluid level switch
G3 E37 B/8 : Front combination lamp LH E5 E67 B/2 : Ambient sensor F
D4 E38 B/8 : Front combination lamp RH E4 E68 B/1 : Horn (Low)
cardiagn.com
F3 E39 B/10 D4 E69 B/1 : Horn (High)
module engine room) G
E2 E40 B/2 : Brake fluid level switch B4 E70 BR/3 : Intelligent Key warning buzzer
E2 E42 B/2 C3 E75 L/4 : ICC brake hold relay H
module engine room)
F2 E43 W/16 F5 E76 B/8 : ICC sensor
module engine room)
: IPDM E/R (Intelligent power distribution : ABS actuator and electric unit (Control I
G2 E44 W/6 C2 E125 B/38
module engine room) unit) (With intelligent cruise control)
PG

HARNESS
< WIRING DIAGRAM >
ENGINE ROOM HARNESS (WITH MR16DDT)
cardiagn.com
ABMIA0311ZZ

E1 E1 GR/5 : Front wiper motor E2 E48 B/6
module engine room)
B3 E6 BR/6 : Fuel injector relay G3 E50 B/2 : Front combination lamp LH
C5 E8 B/2 : Front washer motor B4 E51 B/2 : Front combination lamp RH
A3 E9 — : Body ground A3 E52 GR/2 : Front wheel sensor RH
D2 E10 BR/2 : Fusible link box (Battery) E4 E57 B/1 : Horn (Low)

HARNESS
< WIRING DIAGRAM >
D2 E11 GR/2 : Fusible link box (Battery) B5 E55 B/2 : Daytime running light RH
A
F2 E15 — : Body ground C5 E58 BR/1 : Horn (High)
E2 E17 B/32 : ECM (With MR16DDT) G1 E61 GR/2 : Front wheel sensor LH
E3 E18 B/3 : To E201 F1 E62 B/10 : Joint connector-E04 B
D3 E19 B/2 : To E202 F2 E64 B/48 : To F50
E4 E23 Y/2 : Crash zone sensor B4 E65 BR/2 : Washer fluid level switch
E1 E24 B/10 : Joint connector-E05 B3 E66 L/4 : High pressure fuel pump relay C
G4 E27 B/2 : Front fog lamp LH E4 E67 B/2 : Ambient sensor
B5 E28 B/2 : Front fog lamp RH E4 E68 B/1 : Horn (Low)
D
F4 E35 B/3 : Refrigerant pressure sensor C5 E69 B/1 : Horn (High)
G3 E37 B/8 : Front combination lamp LH B4 E70 BR/3 : Intelligent Key warning buzzer
C4 E38 B/8 : Front combination lamp RH D3 E88 B/2 : To E203 E
: IPDM E/R (Intelligent power distribution : ABS actuator and electric unit (Control
F2 E39 B/10 C2 E125 B/38
module engine room) unit) (With VDC)
D2 E40 B/2 : Brake fluid level switch Engine Room sub-harness F
E2 E42 B/2 E3 E201 B/3 : To E18
cardiagn.com
module engine room)
G
F1 E43 W/16 D3 E202 B/2 : To E19
module engine room)
F2 E44 W/6 D3 E203 B/2 : To E88 H
module engine room)
: IPDM E/R (Intelligent power distribution : Engine coolant temperature sensor 2
E2 E45 BR/12 D4 E204 B/2
module engine room) (With MR16DDT)
: IPDM E/R (Intelligent power distribution I
F2 E46 W/12 D4 E205 B/4 : Cooling fan relay
module engine room)
E2 E47 BR/8 E3 E206 GR/3 : Cooling fan control module
module engine room) J
G3 E54 B/2 : Daytime running light LH
PG

HARNESS
< WIRING DIAGRAM >
ENGINE ROOM HARNESS (PASSENGER COMPARTMENT)
cardiagn.com
AAMIA0618ZZ
C2 E2 B/12 : Joint connector-E02 D4 E32 BR/2 : Clutch pedal position switch

C2 E3 B/12 : Joint connector-E01 C3 E34 BR/2 : Clutch interlock switch
B4 E4 W/100 : To M2 D4 E36 BR/2 : Brake pedal position switch
B5 E5 W/4 : To B3 B3 E41 — : Ground
E4 E12 B/6 : Accelerator pedal position sensor E3 E60 W/4 : Stop lamp switch

HARNESS
< WIRING DIAGRAM >
: Brake pedal position switch
C5 E13 W/24 : To B9 D4 E86 W/4
(With intelligent cruise control) A
C2 E25 B/2 : To M17
ENGINE CONTROL HARNESS (WITH MRA8DE M/T) B
cardiagn.com
G
PG
AAMIA0812ZZ
C4 F2 B/3 : Engine oil pressure sensor E2 F31 GR/4 : Mass air flow sensor
: Intake valve timing control solenoid
B4 F3 B/2 : A/C compressor A3 F33 GR/2
valve

HARNESS
< WIRING DIAGRAM >
: Ignition coil no. 1 (With power
E3 F6 GR/2 : Engine coolant temperature sensor B3 F34 GR/3
transistor)
D3 F7 B/6 : Electric throttle control actuator C3 F35 GR/3
transistor)
C4 F9 — : Engine ground C3 F36 GR/3
transistor)
B4 F10 GR/2 : A/C compressor D3 F37 GR/3
transistor)
C5 F11 B/10 : Joint connector-F03 E4 F39 B/3 : Camshaft position sensor (PHASE)
: Air fuel ratio (A/F) sensor 1 (Except
D2 F12 BR/4 E3 F41 — : Fusible link box (Battery)
for California)
: Evap canister purge volume control
D2 F13 B/2 D1 F43 GR/4 : Heated oxygen sensor 2
solenoid valve
C5 F14 — : Generator E3 F44 — : Fusible link box (Battery)
B5 F15 B/3 : Generator C5 F48 GR/2 : Engine oil temperature sensor
C3 F16 — : Engine ground G3 F50 B/48 : To E64
B4 F18 GR/2 : Fuel injector no.1 E4 F51 B/6 : Joint connector-F01
C3 F19 GR/2 : Fuel injector no.2 F4 F52 G/3 : Park/neutral position (PNP) switch
cardiagn.com
C3 F20 GR/2 : Fuel injector no.3 G4 F54 GR/4 : Battery current sensor
: Exhaust valve timing control solenoid
D3 F21 GR/2 : Fuel injector no.4 A2 F55 GR/2
valve
D5 F22 B/3 : Crankshaft position sensor (POS) E5 F56 B/2 : Intake manifold tuning valve motor
: Exhaust valve timing control position
F5 F24 B/48 : ECM E2 F57 B/3
sensor
F5 F25 BR/48 : ECM F3 F58 B/6 : Joint connector-F02
D3 F27 — : Starter motor C3 F62 GR/2 : Knock sensor
D3 F28 — : Starter motor

HARNESS
< WIRING DIAGRAM >
ENGINE CONTROL HARNESS (WITH MRA8DE CVT)
A
cardiagn.com
G
PG
AAMIA0813ZZ
P
: Intake manifold runner control valve
D4 F1 B/2 F2 F30 B/3 : Secondary speed sensor
motor
C5 F2 B/3 : Engine oil pressure sensor F2 F31 GR/4 : Mass air flow sensor
B4 F3 B/2 : A/C compressor B3 F33 GR/2
valve

HARNESS
< WIRING DIAGRAM >
E3 F6 GR/2 : Engine coolant temperature sensor B3 F34 GR/3
transistor)
D3 F7 B/6 : Electric throttle control actuator C3 F35 GR/3
transistor)
C4 F9 — : Engine ground C3 F36 GR/3
transistor)
B4 F10 GR/2 : A/C compressor D3 F37 GR/3
transistor)
D5 F11 B/10 : Joint connector-F03 F3 F38 B/3 : Primary speed sensor
: Air fuel ratio (A/F) sensor 1 (Except
D2 F12 BR/4 E4 F39 B/3 : Camshaft position sensor (PHASE)
for California)
: Evap canister purge volume control
D2 F13 B/2 E3 F41 — : Fusible link box (Battery)
solenoid valve
: Air fuel ratio (A/F) sensor 1 (For
C5 F14 — : Generator E2 F42 GR/4
California)
B5 F15 B/3 : Generator D1 F43 GR/4 : Heated oxygen sensor 2
C3 F16 — : Engine ground E3 F44 — : Fusible link box (Battery)
B3 F18 GR/2 : Fuel injector no.1 F3 F46 GR/25 : CVT unit
cardiagn.com
C3 F19 GR/2 : Fuel injector no.2 C4 F48 GR/2 : Engine oil temperature sensor
C3 F20 GR/2 : Fuel injector no.3 E2 F49 B/3 : Output speed sensor
D3 F21 GR/2 : Fuel injector no.4 G3 F50 B/48 : To E64
D5 F22 B/3 : Crankshaft position sensor (POS) E5 F51 B/6 : Joint connector-F01
G3 F23 B/48 : TCM (Transmission control module) G4 F54 GR/4 : Battery current sensor
F5 F24 B/48 : ECM A2 F55 GR/2
valve
F5 F25 BR/48 : ECM E5 F56 B/2 : Intake manifold tuning valve motor
: Exhaust valve timing control position
F3 F26 B/10 : Transmission range switch D2 F57 B/3
sensor
D3 F27 — : Starter motor F3 F58 B/6 : Joint connector-F02
D3 F28 — : Starter motor C3 F62 GR/2 : Knock sensor
B4 F29 B/3
position sensor

HARNESS
< WIRING DIAGRAM >
ENGINE CONTROL HARNESS (WITH MR16DDT M/T)
A
cardiagn.com
G
PG
AAMIA0814ZZ
P
E4 F1 B/2 D3 F39 B/3 : Camshaft position sensor (PHASE)
motor
C4 F2 B/3 : Engine oil pressure sensor E4 F40 B/10 : Joint connector-F05
B4 F3 B/2 : A/C compressor E3 F41 — : Fusible link box (Battery)
D3 F6 GR/2 : Engine coolant temperature sensor 1 C4 F48 GR/2 : Engine oil temperature sensor
C3 F8 GR/2 : Knock sensor G4 F50 B/48 : To E64

HARNESS
< WIRING DIAGRAM >
C4 F9 — : Engine ground E4 F51 B/6 : Joint connector-F04
B4 F10 GR/2 : A/C compressor E3 F52 G/3 : Park/neutral position (PNP) switch
C3 F11 B/10 : Joint connector-F03 F3 F54 GR/4 : Battery current sensor
: EVAP canister purge volume control : Exhaust valve timing control solenoid
D4 F13 L/2 B3 F55 GR/2
solenoid valve valve
C5 F14 — : Generator E4 F59 B/24 : Joint connector-F01
C5 F15 B/3 : Generator F4 F60 B/65 : ECM (With MR16DDT)
C3 F16 — : Engine ground F4 F61 B/55 : ECM (With MR16DDT)
B4 F18 GR/2 : Fuel injector no. 1 E3 F64 GR/5 : Multi-way control valve
C4 F19 GR/2 : Fuel injector no. 2 D2 F65 GR/5 : Electric wastegate control actuator
: Intake valve timing intermediate lock
C4 F20 GR/2 : Fuel injector no. 3 B3 F66 BR/2
control solenoid valve
D4 F21 GR/2 : Fuel injector no. 4 D4 F68 B/3 : Fuel rail pressure sensor
D4 F22 B/3 : Crankshaft position sensor (POS) D3 F71 GR/2 : High pressure fuel pump
D4 F27 — : Starter motor D4 F72 B/4 : Turbocharger boost sensor
D3 F28 — : Starter motor D2 F75 BR/2 : Turbocharger bypass control valve
cardiagn.com
: Intake manifold runner control valve : Electric throttle control actuator
B4 F29 B/3 E5 F88 B/6
position sensor (With MR16DDT)
: Engine oil pressure control solenoid
E2 F31 B/4 : Mass air flow sensor C5 F90 GR/2
valve
B3 F33 GR/2 D1 F91 GR/4 : Heated oxygen sensor (With MR16DDT)
valve
: Ignition coil no. 1 (With power : Air fuel ratio (A/F) sensor 1
B3 F34 GR/3 B3 F92 B/4
transistor) (With MR16DDT)
C3 F35 GR/3 D2 F93 B/3 : EGR pressure sensor
transistor)
C3 F36 GR/3 E2 F94 B/5 : EGR volume control valve
transistor)
D3 F37 GR/3 D5 F95 B/3 : Manifold absolute pressure sensor
transistor)

HARNESS
< WIRING DIAGRAM >
ENGINE CONTROL HARNESS (WITH MR16DDT CVT)
A
cardiagn.com
G
PG
AAMIA0815ZZ
P
E4 F1 B/2 D3 F39 B/3 : Camshaft position sensor (PHASE)
motor
C4 F2 B/3 : Engine oil pressure sensor E4 F40 B/10 : Joint connector-F05
B4 F3 B/2 : A/C compressor E3 F41 — : Fusible link box (Battery)
D3 F6 GR/2 : Engine coolant temperature sensor 1 C4 F48 GR/2 : Engine oil temperature sensor
C3 F8 GR/2 : Knock sensor (With MR16DDT) G4 F50 B/48 : To E64

HARNESS
< WIRING DIAGRAM >
C4 F9 — : Engine ground E4 F51 B/6 : Joint connector-F04
B4 F10 GR/2 : A/C compressor F3 F54 GR/4 : Battery current sensor
C3 F11 B/10 : Joint connector-F03 B3 F55 GR/2
valve
: EVAP canister purge volume control
D4 F13 L/2 E4 F59 B/24 : Joint connector-F01
solenoid valve
C5 F14 — : Generator F4 F60 B/65 : ECM (With MR16DDT)
C5 F15 B/3 : Generator F4 F61 B/55 : ECM (With MR16DDT)
C3 F16 — : Engine ground E3 F64 GR/5 : Multi-way control valve
B4 F18 GR/2 : Fuel injector no.1 D2 F65 GR/5 : Electric wastegate control actuator
: Intake valve timing intermediate lock
C4 F19 GR/2 : Fuel injector no.2 B3 F66 BR/2
control solenoid valve
C4 F20 GR/2 : Fuel injector no.3 D5 F68 B/3 : Fuel rail pressure sensor
D4 F21 GR/2 : Fuel injector no.4 D3 F71 GR/2 : High pressure fuel pump
D5 F22 B/3 : Crankshaft position sensor (POS) D4 F72 B/4 : Turbocharger boost sensor
E4 F26 B/10 : Transmission range switch D2 F75 BR/2 : Turbocharger bypass control valve
: TCM (Transmission control module) (With
cardiagn.com
D4 F27 — : Starter motor G3 F81 B/48
MR16DDT)
D3 F28 — : Starter motor F4 F82 GR/25 : CVT unit (With MR16DDT)
B4 F29 B/3 E4 F83 B/3 : Input speed sensor (With MR16DDT)
position sensor
: Electric throttle control actuator (With
E2 F30 B/3 : Output speed sensor E5 F88 B/6
MR16DDT)
: Engine oil pressure control solenoid
E2 F31 B/4 : Mass air flow sensor C4 F90 GR/2
valve
B3 F33 GR/2 D1 F91 GR/4 : Heated oxygen sensor (With MR16DDT)
valve
: Ignition coil no. 1 (With power : Air fuel ratio (A/F) sensor 1 (With
B3 F34 GR/3 B3 F92 B/4
transistor) MR16DDT)
C3 F35 GR/3 D2 F93 B/3 : EGR pressure sensor
transistor)
C3 F36 GR/3 D2 F94 B/5 : EGR volume control valve
transistor)
D3 F37 GR/3 D5 F95 B/3 : Manifold absolute pressure sensor
transistor)
F4 F38 B/3 : Primary speed sensor

HARNESS
< WIRING DIAGRAM >
MAIN HARNESS
A
cardiagn.com
G
PG
AAMIA0809ZZ
P
F3 M1 W/24 : To B92 C2 M58 B/6 : Intake door motor (With auto A/C)
A4 M2 W/100 : To E4 E3 M59 B/10 : A/C switch assembly (With auto A/C)
B4 M3 W/1 : Fuse block (J/B) E1 M60 W/20 : Joint connector-M06
B4 M4 W/1 : Fuse block (J/B) F1 M61 — : Body ground

HARNESS
< WIRING DIAGRAM >
F3 M5 W/16 : To B4 D1 M62 W/2 : Blower motor
A3 M6 L/4 : Heated seat relay C4 M64 B/8 : VDC off switch
G3 M7 W/16 : To B2 A3 M65 L/4 : Accessory relay-2
B5 M8 W/12 : To B8 B2 M66 W/8 : Illumination control switch
G3 M9 W/32 : To B10 D2 M68 BR/2 : Intake sensor
A4 M10 W/24 : To B11 D3 M69 W/2 : In-vehicle sensor
E4 M11 BR/6 : Heated seat switch RH E1 M70 W/2 : Sunload sensor
E4 M12 W/6 : Heated seat switch LH G1 M71 L/20 : Joint connector-M05
A3 M13 W/55 : To D2 B1 M72 W/3 : Optical sensor
D3 M14 W/8 : Steering angle sensor G2 M74 W/55 : To D101
C3 M15 W/4 : Trunk lid opener switch E1 M76 B/2 : Front passenger air bag module
D1 M16 BR/2 : Front passenger air bag off indicator E1 M77 O/2 : Front passenger air bag module
B4 M17 B/2 : To E25 C2 M78 W/20 : Joint connector-M02
C2 M18 — : Body ground D3 M80 GR/8 : Combination switch (Spiral cable)
D4 M19 B/3 : Front console power socket C4 M81 L/8 : Sport mode switch
: BCM (Body control module) (Without
cardiagn.com
A3 M20 W/15 C4 M82 GR/8 : ECO mode switch
: BCM (Body control module) (Without : BCM (Body control module) (With
A3 M21 W/40 A3 M83 W/40
Intelligent Key system) Intelligent Key system)
C4 M22 W/16 : Data link connector A3 M84 B/40
D2 M23 W/12 : To M125 B3 M85 W/15
C2 M24 W/40 : Combination meter (With type A) E3 M86 L/2 : Inside key antenna (Instrument center)
D4 M25 W/8 : Push-button ignition switch C1 M87 W/8 : EPS control unit
C3 M26 W/6 : Ignition switch E2 M88 B/2 : Diode-3
C4 M28 W/14 : Combination switch F5 M89 L/2 : Inside key antenna (Console)
: Remote keyless entry receiver (With
E3 M29 W/40 : A/C auto amp (Without A/C) E2 M91 W/4
: Audio unit (With display audio
C4 M30 Y/6 : Combination switch (Spiral cable) E3 M92 W/20
system)
: Audio unit (With display audio
C1 M31 L/20 : Joint connector-M01 E2 M93 W/32
system)
D2 M32 W/16 : To M124 D4 M95 W/16 : CVT shift selector (With MR16DDT)
E3 M33 W/40 : A/C auto amp. (With manual A/C) E3 M96 B/6 : Audio unit (With base audio system)
: Audio (With display audio
F3 M34 W/40 : A/C auto amp. (With auto A/C) E3 M97 B/6
system)
D4 M35 Y/28 : Air bag diagnosis sensor unit B5 M98 W/20 : To B68
: Audio (With display audio
D2 M36 — : Diode-1 D3 M99 W/8
system)
: AV control unit (With navigation system
C1 M37 B/2 : EPS control unit F3 M100 W/20
with BOSE® audio system)
D4 M38 W/16 : CVT shift selector (With MRA8DE) D2 M101 W/24
with BOSE audio system)
D1 M39 W/4 : Dongle unit D1 M102 W/4 : Hazard switch
G1 M40 W/20 : Joint connector-M04 F3 M103 W/20
without BOSE audio system)
A1 M41 W/20 : To R1 D2 M104 W/24
without BOSE audio system)

HARNESS
< WIRING DIAGRAM >
C2 M42 W/4 : NATS antenna amp. F3 M114 B/6
with BOSE audio system) A
E3 M43 W/20 : Audio unit (With base audio system) C1 M122 W/40 : Combination meter (With type B)
E2 M44 W/32 : Audio unit (With base audio system) C2 M123 W/12 : Combination meter (With type B)
B
F2 M45 W/32 : Bluetooth control unit B3 M129 W/16 : Door mirror remote control switch
A2 M46 BR/2 : Front tweeter LH E5 M130 B/1 : Parking brake switch
: Remote keyless entry receiver (Without C
G1 M47 BR/2 : Front tweeter RH F2 M131 W/4
C2 M48 B/6 : Intake door motor (Without manual A/C) G4 M132 B/6 : USB interface
F2 M49 W/8 : Bluetooth control unit E5 M133 W/4 : Aux jack D
C3 M50 GR/6 : Key switch B2 M148 W/24 : ADAS control unit
E3 M51 W/16 : A/C switch assembly (Without auto A/C) E2 M149 W/2 : Warning buzzer
E
D2 M52 W/4 : Variable blower control F1 M150 B/40 : TCU
: AV control unit (With navigation with
E1 M53 L/20 : Joint connector-M03 D2 M151 G/6
BOSE audio system)
F
D1 M54 G/20 : Joint connector-M07 E1 M152 G/6 : TCU
B2 M57 — : Body ground
cardiagn.com
G
PG

HARNESS
< WIRING DIAGRAM >
ROOM LAMP HARNESS
cardiagn.com
AAMIA0622ZZ
: Auto anti-dazzling inside mirror (Without

G4 R1 W/20 : To M41 D4 R13 B/7
Homelink® universal transceiver)
: Auto anti-dazzling inside mirror (With
C2 R3 W/8 : Map lamp D4 R15 B/10
Homelink® universal transceiver)
D3 R4 W/6 : Microphone C2 R21 W/8 : Telematic switch
C2 R5 W/4 : Interior room lamp D2 R26 GR/10 : Moonroof motor assembly

HARNESS
< WIRING DIAGRAM >
E2 R7 W/2 : Vanity mirror lamp LH C3 R27 W/12 : Moonroof switch
A
B4 R8 W/2 : Vanity mirror lamp RH
cardiagn.com
G
PG

FUSE BLOCK - JUNCTION BOX (J/B)
< WIRING DIAGRAM >
FUSE BLOCK - JUNCTION BOX (J/B)
Terminal Arrangement INFOID:0000000014525332
cardiagn.com
AAMIA5761GB

FUSE, FUSIBLE LINK AND RELAY BOX
< WIRING DIAGRAM >
A
Terminal Arrangement INFOID:0000000014525333
FUSE, FUSIBLE LINK BOX, AND RELAY BOX B
cardiagn.com
G
PG
AAMIA5758GB

< WIRING DIAGRAM >
cardiagn.com
AAMIA5760GB

< WIRING DIAGRAM >
cardiagn.com
G
PG
AAMIA5759GB

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< WIRING DIAGRAM >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
IPDM E/R Terminal Arrangement INFOID:0000000014525334
cardiagn.com
ABMIA5674GB
NOTE:
Numbers preceded by an "F" represent the fuse numbers imprinted on the IPDM E/R. The other numbers
represent the fuse numbers as they appear in the wiring diagrams.

BATTERY
< BASIC INSPECTION >
BASIC INSPECTION A
BATTERY
How to Handle Battery INFOID:0000000014525335
B
CAUTION:
• If it becomes necessary to start the engine with a booster battery and jumper cables, use a 12-volt
booster battery. C
• After connecting battery cables, ensure that they are tightly clamped to battery terminals for good
contact.
• Never add distilled water through the hole used to check specific gravity. D
METHODS OF PREVENTING OVER-DISCHARGE
The following precautions must be taken to prevent over-discharging a battery. E
• The battery surface (particularly its top) should always be kept
clean and dry.
• The terminal connections should be clean and tight.
• At every routine maintenance, check the electrolyte level. F
This also applies to batteries designated as “low maintenance” and
“maintenance-free”.
cardiagn.com
G
H
MEL040F
• When the vehicle is not going to be used over a long period of I

time, disconnect the battery cable from the negative terminal. (If
the vehicle has an extended storage switch, turn it off.)
J
ELA0349D L
Work Flow INFOID:0000000014525336
PG
BATTERY DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NI
To diagnose and confirm the condition of the battery, use the following special service tools:
• EXP-800 NI Battery and electrical diagnostic analyzer N
• GR8-1200 NI Multitasking battery and electrical diagnostic station
NOTE:
Refer to the applicable Instruction Manual for proper battery diagnosis procedures.
O
BATTERY DIAGNOSIS WITHOUT EXP-800 NI OR GR8-1200 NI
Checking Electrolyte Level
WARNING: P
Never allow battery fluid to come in contact with skin, eyes, fabrics, or painted surfaces. After touch-
ing a battery, never touch or rub your eyes until you have thoroughly washed your hands. If acid con-
tacts eyes, skin or clothing, immediately flush with water for 15 minutes and seek medical attention.
Failure to do this may cause personal injury or damage to clothing or the painted surfaces.

BATTERY
• Remove the cell plug using a suitable tool.
• Add distilled water up to the MAX level.
MEL043F
SULFATION
• A battery will be completely discharged if it is left unattended
for a long time and the specific gravity will become less than
1.100. This may result in sulfation on the cell plates.
• To determine if a battery has been “sulfated”, note its voltage
and current when charging it. As shown in the figure, less cur-
rent and higher voltage are observed in the initial stage of
charging sulfated batteries.
• A sulfated battery may sometimes be brought back into ser-
cardiagn.com
vice by means of a long, slow charge, 12 hours or more, fol-
lowed by a battery capacity test.
PKIA2353E
Specific Gravity Check

NOTE:
Check the charge condition of the battery.
Periodically check the specific gravity of the electrolyte. Keep a close check on charge condition to prevent
over-discharge.
1. Read hydrometer and thermometer indications at eye level.
2. Use the chart below to correct your hydrometer reading accord-
ing to electrolyte temperature.
MEL042FA
Hydrometer Temperature Correction
Battery electrolyte temperature [°C (°F)] Add to specific gravity reading

71 (160) 0.032
66 (150) 0.028
60 (140) 0.024
54 (130) 0.020
49 (120) 0.016
43 (110) 0.012
38 (100) 0.008
32 (90) 0.004
27 (80) 0
21 (70) −0.004
16 (60) −0.008
10 (50) −0.012

BATTERY
Battery electrolyte temperature [°C (°F)] Add to specific gravity reading
A
4 (40) −0.016
−1 (30) −0.020
−7 (20) −0.024 B
−12 (10) −0.028
−18 (0) −0.032
C
Corrected specific gravity Approximate charge condition
1.260 - 1.280 Fully charged
D
1.230 - 1.250 3/4 charged
1.200 - 1.220 1/2 charged
1.170 - 1.190 1/4 charged E
1.140 - 1.160 Almost discharged
1.110 - 1.130 Completely discharged
F
Charging The Battery
CAUTION:
cardiagn.com
• Never “quick charge” a fully discharged battery. G
• Keep the battery away from open flame while it is being charged.
• When connecting the charger, connect the leads first, then turn on the charger. Never turn on the
charger first, as this may cause a spark.
• If battery electrolyte temperature rises above 55 °C (131 °F), stop charging. Always charge battery at H
a temperature below 55 °C (131 °F).
Charging Rates (Standard Charge)
I
Approximate charge condi-
Charge current (A) Charge time (h)
tion
Fully charged 2
J
3/4 charged 2.5
1/2 charged 5
7
1/4 charged 7.5 K
Almost discharged 9
Completely discharged 10
L
Charging Rates (Quick Charge)
Approximate charge condi-

Charge current (A) Charge time (h)
tion PG
Fully charged — —
3/4 charged 16
1/2 charged N
0.5
1/4 charged 33
Almost discharged
O
Completely discharged — —
NOTE:
The ammeter reading on your battery charger will automatically decrease as the battery charges. This indi- P
cates that the voltage of the battery is increasing normally as the state of charge improves. The charging amps
indicated above refer to initial charge rate.
• If, after charging, the specific gravity of any two cells varies more than 0.050, the battery should be replaced.

INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement INFOID:0000000014525337
Required Procedure After Battery Disconnection

System Item Reference
EC-182 (MR16DDT)
Engine Control System Idle Air Volume Learning
EC-813 (MRA8DE)
Power Window Control System Power Window System Initialization PWC-41
Roof Moonroof Memory Reset/Initialization RF-22
Temperature Setting Trimmer HAC-55 (Automatic Air Conditioner)
Inlet Port Memory Function (FRE) HAC-55 (Automatic Air Conditioner)
Heater & Air Conditioning Control System
Inlet Port Memory Function (REC) HAC-56 (Automatic Air Conditioner)
Target Evaporator Temp Upper Limit HAC-56 (Automatic Air Conditioner)
Audio (Radio Preset) Refer to Owner's Manual.
cardiagn.com
Audio, Visual & Navigation System
Navigation System Refer to Owner's Manual.

FUSE INSPECTION
FUSE INSPECTION
A
How To Check INFOID:0000000014525338
• If fuse is blown, be sure to eliminate cause of malfunction before B

installing new fuse.
• Use fuse of specified rating. Never use fuse of more than specified
rating.
• Do not partially install fuse; always insert it into fuse holder prop- C
erly.
• Remove fuse for “ELECTRICAL PARTS (BAT)” if vehicle is not
used for a long period of time. D
CEL083 E
EXTENDED STORAGE SWITCH (IF EQUIPPED)
NOTE:
• When extended storage switch is pulled out, a message may be shown in the meter or display. To turn mes- F
sage/display off, push extended storage switch in.
• The following information is related to extended storage switch (shipping mode). For information related to
cardiagn.com
BCM transit mode, refer to BCS-16, "SHIPPING MODE CONTROL SYSTEM : System Description".
G
The following switch may be mounted on the fuse block (Junction Box) for transportation and storage.
PG
JSMIA0793ZZ P
Extended storage switch

Type A Type B Type C
Remove the extended storage switch if it interferes when checking fuses.

How/When to turn Extended Storage Switch ON/OFF
CAUTION:
FUSE INSPECTION
• Turn the ignition switch OFF when operating the extended storage switch.
• Under normal conditions, keep the extended storage switch in ON state. Never operate the extended
storage switch except when necessary.
• Type A
JSMIA0472ZZ
- To turn the extended storage switch OFF, pull out in direction as shown in the figure.
cardiagn.com
- To turn the extended storage switch ON, press in direction as shown in the figure.
• Type B
JSMIA0473ZZ
- To turn the extended storage switch OFF, pinch tabs of the switch and pull out in direction as shown in
the figure.
• Type C
JSMIA0794ZZ
- To turn the extended storage switch OFF, pull out in direction as shown in the figure.

FUSE INSPECTION
How To Remove Extended Storage Switch
A
Type A
1. Turn the ignition switch OFF.
2. Turn the extended storage switch OFF.
3. Pinch tabs and tilt to disengage the extended storage switch. B
Pinch tabs to remove the extended storage switch.
JSMIA0476ZZ
E
CAUTION:
For bus bar type extended storage switch, never replace bus bar with a fuse, or fuse may continu- F
ally open.
NOTE:
cardiagn.com
• Extended storage switch and fuse (or bus bar) are removed together. Remove fuse (or bus bar) from G
extended storage switch, if necessary.
• Install removed fuse (or bus bar) to fuse block.
• Extended storage switch is for transportation and storage. Reinstallation of switch is not required after
removal, but fuse (or bus bar) must be reinstalled/pushed back in to activate all electrical systems and H
turn message off (which may be shown in meter/display).
Type B
I
3. Pinch tabs and firmly pull out the extended storage switch in
direction. J
JSMIA0477ZZ
PG
CAUTION:
For bus bar type extended storage switch, never replace bus bar with a fuse, or fuse may continu-
ally open. N
NOTE:
• Extended storage switch and fuse (or bus bar) may be removed together. Remove fuse (or bus bar)
from extended storage switch, if necessary. O
removal, but fuse (or bus bar) must be reinstalled/pushed back in to activate all electrical systems and
turn message off (which may be shown in meter/display). P
Type C

FUSE INSPECTION
3. Pinch tabs and firmly pull out the extended storage switch in
direction.
JSMIA0795ZZ
CAUTION:
For bus bar type extended storage switch, never replace bus bar with a fuse, or fuse may continu-
ally open.
NOTE:
• Extended storage switch and fuse (or bus bar) are removed together. Remove fuse (or bus bar) from
extended storage switch, if necessary.
removal, but fuse (or bus bar) must be reinstalled/pushed back in to activate all electrical systems and
cardiagn.com
turn message off (which may be shown in meter/display).

FUSIBLE LINK INSPECTION
FUSIBLE LINK INSPECTION
A
Fusible Link INFOID:0000000014525339
A melted fusible link can be detected either by visual inspection or by B

feeling with finger tip. If its condition is questionable, use circuit
tester or test lamp.
1 : Fusible link C
CAUTION:
• If fusible link should melt, it is possible that critical circuit
(power supply or large current carrying circuit) is shorted. In D
such a case, carefully check and eliminate cause of malfunc-
tion.
• Never wrap outside of fusible link with vinyl tape. Important: JSMIA0352ZZ E
Never let fusible link touch any other wiring harness, vinyl or
rubber parts.
F
cardiagn.com
G
PG

BATTERY
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
BATTERY
Exploded View INFOID:0000000014525340
cardiagn.com
AWMIA1903ZZ
1. Battery frame 2. Battery rods 3. Battery cover

4. Battery bracket 5. Battery tray 6. Battery
Front
Battery Disconnect INFOID:0000000014910500
WARNING:
Battery acid and battery acid fumes are extremely dangerous and can cause severe burns and explo-
sion. To help reduce the risk of personal injury:
• Wear appropriate goggles and protective clothing.
• Always properly ventilate the area where the service is being performed.
• Do not allow battery fluid to come in contact with skin, eyes, fabrics, or painted surfaces.
• To avoid arcing, remove the negative (-) battery cable first and attach the (-) negative battery cable
last.
• If acid contacts eyes, skin, or clothing, immediately flush with water for 15 minutes and seek medical
attention.
REMOVAL
1. Loosen the battery terminal nuts and disconnect both battery negative and positive terminals.
CAUTION:
To prevent damage to the parts, disconnect the battery negative terminal first.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the fusible link box (battery) if it has been dropped or sustained an impact.

BATTERY
• Perform ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL. Refer to PG-
134, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair A
Requirement".
Battery terminal nuts 5.1 N·m (0.52 kg-m, 45 in-lb) B

Removal and Installation (Battery) INFOID:0000000014525341
REMOVAL C
1. Loosen the battery terminal nuts and disconnect both battery negative and positive terminals.
CAUTION:
To prevent damage to the parts, disconnect the battery negative terminal first. D
2. Remove battery frame nuts, battery frame and battery rods.
3. Remove battery cover and battery.
E
4. Remove battery tray (if necessary).
INSTALLATION
Installation is in the reverse order of removal. F
CAUTION:
• To prevent damage to the parts, connect the battery positive terminal first.
cardiagn.com
• Ensure battery cables are tightly clamped to battery terminals for good contact.
• Check battery terminal for poor connection caused by corrosion. G
134, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair
Requirement". H
PG

BATTERY TERMINAL WITH FUSIBLE LINK
BATTERY TERMINAL WITH FUSIBLE LINK
cardiagn.com
ALMIA0952ZZ
1. Battery terminal with fusible link 2. Harness connector
Removal and Installation INFOID:0000000014525344
REMOVAL
1. Loosen the battery terminal nuts and disconnect both battery negative and positive terminals. Refer to
PG-140, "Battery Disconnect".
CAUTION:
To prevent damage to the parts, disconnect the battery negative terminal first.
2. Remove harness nut and battery terminal with fusible link nut.
3. Disconnect harness connectors and remove battery terminal with fusible link.
INSTALLATION
CAUTION:
• To prevent damage to the parts, connect the battery positive terminal first.
134, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair
Requirement".

BATTERY CURRENT SENSOR
BATTERY CURRENT SENSOR
A
cardiagn.com
G
ALMIA0953ZZ
1. Battery current sensor 2. Current sensor harness connector H
Removal and Installation INFOID:0000000014525346
I
REMOVAL
1. Loosen the battery terminal nut and disconnect battery negative terminal. Refer to PG-140, "Battery Dis-
connect". J
2. Disconnect the harness connector from battery current sensor.
3. Remove the nut and battery current sensor from negative terminal.
K
INSTALLATION
CAUTION:
Perform ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL. Refer to PG-134, L
"ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Require-
ment".
PG

SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
Battery INFOID:0000000014525347
Type (Engine)* GR21R (MRA8DE) GR35 (MR16DDT)

Capacity (20HR) minimum V-AH 12 - 49 12 - 63
Cold cranking current A (For reference value) 470 550
*: Always check with the Parts Department for the latest parts information.
cardiagn.com

Power Supply, Ground & Circuit Elements: Section

Uploaded by

Copyright:

Available Formats

Power Supply, Ground & Circuit Elements: Section

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Power Supply, Ground & Circuit Elements: Section

Uploaded by

Copyright:

Available Formats

ELECTRICAL & POWER CONTROL

POWER SUPPLY, GROUND & CIRCUIT ELEMENTS

Revision: December 2016 PG-1 2017 Sentra NAM

Revision: December 2016 PG-2 2017 Sentra NAM

Revision: December 2016 PG-3 2017 Sentra NAM

— Tests batteries and charging systems.

Commercial Service Tool INFOID:0000000014525322

Tool name Description

Revision: December 2016 PG-4 2017 Sentra NAM

Revision: December 2016 PG-5 2017 Sentra NAM

Revision: December 2016 PG-6 2017 Sentra NAM

Revision: December 2016 PG-7 2017 Sentra NAM

Revision: December 2016 PG-8 2017 Sentra NAM

For example, when current is 30A, the circuit is broken within 8 to 20 B

HARNESS CONNECTOR (TAB-LOCKING TYPE) F

Revision: December 2016 PG-9 2017 Sentra NAM

HARNESS CONNECTOR (SLIDE-LOCKING TYPE)

Revision: December 2016 PG-10 2017 Sentra NAM

HARNESS CONNECTOR (LEVER LOCKING TYPE)

Revision: December 2016 PG-11 2017 Sentra NAM

HARNESS CONNECTOR (DIRECT-CONNECT SRS COMPONENT TYPE)

Standardized Relay INFOID:0000000014525326

NORMAL OPEN, NORMAL CLOSED AND MIXED TYPE RELAYS

Revision: December 2016 PG-12 2017 Sentra NAM

TYPE OF STANDARDIZED RELAYS

Revision: December 2016 PG-13 2017 Sentra NAM

Revision: December 2016 PG-14 2017 Sentra NAM

Revision: December 2016 PG-15 2017 Sentra NAM

Revision: December 2016 PG-16 2017 Sentra NAM

Revision: December 2016 PG-17 2017 Sentra NAM

Revision: December 2016 PG-18 2017 Sentra NAM

Revision: December 2016 PG-19 2017 Sentra NAM

Revision: December 2016 PG-20 2017 Sentra NAM

Revision: December 2016 PG-21 2017 Sentra NAM

Revision: December 2016 PG-22 2017 Sentra NAM

Revision: December 2016 PG-23 2017 Sentra NAM

Revision: December 2016 PG-24 2017 Sentra NAM

Revision: December 2016 PG-25 2017 Sentra NAM

Revision: December 2016 PG-26 2017 Sentra NAM

Revision: December 2016 PG-27 2017 Sentra NAM

Revision: December 2016 PG-28 2017 Sentra NAM

Revision: December 2016 PG-29 2017 Sentra NAM

Revision: December 2016 PG-30 2017 Sentra NAM

Revision: December 2016 PG-31 2017 Sentra NAM

Revision: December 2016 PG-32 2017 Sentra NAM

Revision: December 2016 PG-33 2017 Sentra NAM

Revision: December 2016 PG-34 2017 Sentra NAM

Revision: December 2016 PG-35 2017 Sentra NAM

Revision: December 2016 PG-36 2017 Sentra NAM

Revision: December 2016 PG-37 2017 Sentra NAM

Revision: December 2016 PG-38 2017 Sentra NAM

Revision: December 2016 PG-39 2017 Sentra NAM

Revision: December 2016 PG-40 2017 Sentra NAM

Revision: December 2016 PG-41 2017 Sentra NAM

Revision: December 2016 PG-42 2017 Sentra NAM

Revision: December 2016 PG-43 2017 Sentra NAM

Revision: December 2016 PG-44 2017 Sentra NAM

Revision: December 2016 PG-45 2017 Sentra NAM

Revision: December 2016 PG-46 2017 Sentra NAM