Safety Data Sheet: Section 1. Identification

SAFETY DATA SHEET
Date of issue/Date of revision 22 March 2021

Version 22
Section 1. Identification
Product name : AQUAPON Zinc Rich Primer Comp A
Product code : 00338243
Other means of : Not available.
identification
Product type : Liquid.
Relevant identified uses of the substance or mixture and uses advised against
Product use : Professional applications, Used by spraying.
Use of the substance/ : Coating.
mixture
Uses advised against : Not applicable.
Manufacturer : PPG Industries, Inc.

One PPG Place
Pittsburgh, PA 15272
Emergency telephone : (412) 434-4515 (U.S.)
number (514) 645-1320 (Canada)
SETIQ Interior de la República: 800-00-214-00 (México)
SETIQ Ciudad de México: (55) 5559-1588 (México)
Technical Phone Number : 888-977-4762
Section 2. Hazards identification

OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Classification of the : FLAMMABLE LIQUIDS - Category 2
substance or mixture ACUTE TOXICITY (inhalation) - Category 4
SKIN IRRITATION - Category 2
SERIOUS EYE DAMAGE - Category 1
SKIN SENSITIZATION - Category 1
CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION - Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) -
Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2
Percentage of the mixture consisting of ingredient(s) of unknown acute toxicity: 15.1%
(oral), 26.9% (dermal), 17.6% (inhalation)
GHS label elements
United States Page: 1/18

Product code 00338243 Date of issue 22 March 2021 Version 22
Product name AQUAPON Zinc Rich Primer Comp A
Section 2. Hazards identification

Hazard pictograms :
Signal word : Danger

Hazard statements : Highly flammable liquid and vapor.
Causes skin irritation.
May cause an allergic skin reaction.
Causes serious eye damage.
Harmful if inhaled.
May cause respiratory irritation.
May cause drowsiness or dizziness.
Suspected of causing cancer.
Suspected of damaging fertility or the unborn child.
May cause damage to organs through prolonged or repeated exposure. (hearing organs)
Precautionary statements
Prevention : Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves, protective clothing and eye or face
protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Use explosion-proof electrical, ventilating or lighting equipment.
Use non-sparking tools. Take action to prevent static discharges. Use only outdoors or
in a well-ventilated area. Do not breathe vapor. Wash thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Response : IF exposed or concerned: Get medical advice or attention. IF INHALED: Remove
person to fresh air and keep comfortable for breathing. Call a POISON CENTER or
doctor if you feel unwell. IF ON SKIN (or hair): Take off immediately all contaminated
clothing. Rinse skin with water. Wash contaminated clothing before reuse. IF ON SKIN:
Wash with plenty of water. If skin irritation or rash occurs: Get medical advice or
attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing. Immediately call a POISON
CENTER or doctor.
Storage : Store locked up. Store in a well-ventilated place. Keep container tightly closed. Keep
cool.
Disposal : Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Supplemental label : Sanding and grinding dusts may be harmful if inhaled. Repeated exposure to high vapor
elements concentrations may cause irritation of the respiratory system and permanent brain and
nervous system damage. Inhalation of vapor/aerosol concentrations above the
recommended exposure limits causes headaches, drowsiness and nausea and may
lead to unconsciousness or death. This product either contains formaldehyde or is
capable of releasing formaldehyde above 0.5 ppm under certain conditions.
Formaldehyde is a known cancer hazard, a skin sensitizer and a respiratory sensitizer.
Avoid contact with skin and clothing. Wash thoroughly after handling. Emits toxic fumes
when heated.
Hazards not otherwise : Prolonged or repeated contact may dry skin and cause irritation.
classified

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Product name : AQUAPON Zinc Rich Primer Comp A
Ingredient name % CAS number

xylene ≥20 - ≤28 1330-20-7
butan-1-ol ≥20 - ≤24 71-36-3
Fatty acids, C18-unsatd., dimers, oligomeric reaction products with tall-oil ≥10 - ≤20 68082-29-1
fatty acids and triethylenetetramine
diiron trioxide ≥10 - ≤20 1309-37-1
Isopropyl alcohol ≥5.0 - ≤10 67-63-0
4-methylpentan-2-one ≥1.0 - ≤6.4 108-10-1
ethylbenzene ≥1.0 - ≤5.0 100-41-4
toluene <1.0 108-88-3
SUB codes represent substances without registered CAS Numbers.

Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Occupational exposure limits, if available, are listed in Section 8.
Section 4. First aid measures

If ingestion, irritation, any type of overexposure or symptoms of overexposure occur during or persists after use of
this product, contact a POISON CONTROL CENTER, EMERGENCY ROOM OR PHYSICIAN immediately; have
Safety Data Sheet information available. Never give anything by mouth to an unconscious or convulsing person.
Description of necessary first aid measures
Eye contact : Check for and remove any contact lenses. Immediately flush eyes with running water for
at least 15 minutes, keeping eyelids open. Seek immediate medical attention.
Inhalation : Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained
personnel.
Skin contact : Remove contaminated clothing and shoes. Wash skin thoroughly with soap and water
or use recognized skin cleanser. Do NOT use solvents or thinners.
Ingestion : If swallowed, seek medical advice immediately and show this container or label. Keep
person warm and at rest. Do NOT induce vomiting.
Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : Causes serious eye damage.
Inhalation : Harmful if inhaled. Can cause central nervous system (CNS) depression. May cause
drowsiness or dizziness. May cause respiratory irritation.
Skin contact : Causes skin irritation. Defatting to the skin. May cause an allergic skin reaction.
Ingestion : Can cause central nervous system (CNS) depression.
Over-exposure signs/symptoms

Section 4. First aid measures

Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
dryness
cracking
blistering may occur
Ingestion : Adverse symptoms may include the following:
stomach pains
Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : In case of inhalation of decomposition products in a fire, symptoms may be delayed.
The exposed person may need to be kept under medical surveillance for 48 hours.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water
before removing it, or wear gloves.
See toxicological information (Section 11)
Section 5. Fire-fighting measures

Extinguishing media
Suitable extinguishing : Use dry chemical, CO₂, water spray (fog) or foam.
media
Unsuitable extinguishing : Do not use water jet.
media

Section 5. Fire-fighting measures

Specific hazards arising : Highly flammable liquid and vapor. In a fire or if heated, a pressure increase will occur
from the chemical and the container may burst, with the risk of a subsequent explosion. Vapors may
accumulate in low or confined areas or travel a considerable distance to a source of
ignition and flash back. Runoff to sewer may create fire or explosion hazard.
Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon oxides
nitrogen oxides
metal oxide/oxides
Formaldehyde.
Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if
for fire-fighters there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing
equipment for fire-fighters apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Do not breathe vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".
Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Methods and materials for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in which
this product is used. Avoid exposure - obtain special instructions before use. Avoid
exposure during pregnancy. Do not handle until all safety precautions have been read
and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist.
Do not ingest. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless
adequately ventilated. Keep in the original container or an approved alternative made
from a compatible material, kept tightly closed when not in use. Store and use away
from heat, sparks, open flame or any other ignition source. Use explosion-proof
electrical (ventilating, lighting and material handling) equipment. Use only non-sparking
tools. Take precautionary measures against electrostatic discharges. Empty containers
retain product residue and can be hazardous. Do not reuse container.
Special precautions : Vapors may accumulate in low or confined areas or travel a considerable distance to a
source of ignition and flash back. Vapors are heavier than air and may spread along
floors. If this material is part of a multiple component system, read the Safety Data
Sheet(s) for the other component or components before blending as the resulting
mixture may have the hazards of all of its parts.
Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Conditions for safe storage, : Store between the following temperatures: 0 to 35°C (32 to 95°F). Store in accordance
including any with local regulations. Store in a segregated and approved area. Store in original
incompatibilities container protected from direct sunlight in a dry, cool and well-ventilated area, away
from incompatible materials (see Section 10) and food and drink. Store locked up.
Eliminate all ignition sources. Separate from oxidizing materials. Keep container tightly
closed and sealed until ready for use. Containers that have been opened must be
carefully resealed and kept upright to prevent leakage. Do not store in unlabeled
containers. Use appropriate containment to avoid environmental contamination.
Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
xylene ACGIH TLV (United States, 3/2019).
STEL: 651 mg/m³ 15 minutes.
STEL: 150 ppm 15 minutes.
TWA: 434 mg/m³ 8 hours.
TWA: 100 ppm 8 hours.
OSHA PEL (United States, 5/2018).
butan-1-ol ACGIH TLV (United States, 3/2019).


Fatty acids, C18-unsatd., dimers, oligomeric reaction products with tall- None.
oil fatty acids and triethylenetetramine
diiron trioxide OSHA PEL (United States, 5/2018).
TWA: 10 mg/m³ 8 hours. Form: Fume
TWA: 5 mg/m³ 8 hours. Form: Respirable
fraction
TWA: 15 mg/m³ 8 hours. Form: Total dust
ACGIH TLV (United States, 3/2019).
TWA: 5 mg/m³ 8 hours. Form: Respirable
fraction
Isopropyl alcohol ACGIH TLV (United States, 3/2019).
4-methylpentan-2-one ACGIH TLV (United States, 3/2019).
ethylbenzene ACGIH TLV (United States, 3/2019).
toluene OSHA PEL Z2 (United States, 2/2013).
AMP: 500 ppm 10 minutes.
CEIL: 300 ppm
ACGIH TLV (United States, 3/2019).
Key to abbreviations
A = Acceptable Maximum Peak S = Potential skin absorption
ACGIH = American Conference of Governmental Industrial Hygienists. SR = Respiratory sensitization
C = Ceiling Limit SS = Skin sensitization
F = Fume STEL = Short term Exposure limit values
IPEL = Internal Permissible Exposure Limit TD = Total dust
OSHA = Occupational Safety and Health Administration. TLV = Threshold Limit Value
R = Respirable TWA = Time Weighted Average
Z = OSHA 29 CFR 1910.1200 Subpart Z - Toxic and Hazardous Substances
Consult local authorities for acceptable exposure limits.
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace
procedures atmosphere or biological monitoring may be required to determine the effectiveness of
the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to appropriate monitoring standards.
Reference to national guidance documents for methods for the determination of
hazardous substances will also be required.


Appropriate engineering : Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
controls other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Chemical splash goggles and face shield.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Gloves : butyl rubber
Body protection : Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
Other skin protection : Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Respiratory protection : Respirator selection must be based on known or anticipated exposure levels, the
hazards of the product and the safe working limits of the selected respirator. If workers
are exposed to concentrations above the exposure limit, they must use appropriate,
certified respirators. Use a properly fitted, air-purifying or air-fed respirator complying
with an approved standard if a risk assessment indicates this is necessary.
Section 9. Physical and chemical properties

Appearance
Physical state : Liquid.
Color : Not available.
Odor : Characteristic.
Odor threshold : Not available.
pH : Not applicable.
Melting point : Not available.
Section 9. Physical and chemical properties

Boiling point : 82°C (179.6°F)
Flash point : Closed cup: 16.11°C (61°F)
Auto-ignition temperature : Not available.
Decomposition temperature : Not available.
Flammability (solid, gas) : Not available.
Lower and upper explosive : Not available.
(flammable) limits
Evaporation rate : Not available.
Vapor pressure : Not available.
Vapor density : Not available.
Relative density : 0.97
Density ( lbs / gal ) : 8.1
Solubility : Insoluble in the following materials: cold water.
Partition coefficient: n- : Not available.
octanol/water
Viscosity : Kinematic (40°C (104°F)): >0.21 cm2/s (>21 cSt)
Volatility : 82% (v/v), 70.359% (w/w)
% Solid. (w/w) : 29.641
Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.
Chemical stability : The product is stable.
Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions
Conditions to avoid : When exposed to high temperatures may produce hazardous decomposition products.
Refer to protective measures listed in sections 7 and 8.
Incompatible materials : Keep away from the following materials to prevent strong exothermic reactions:
oxidizing agents, strong alkalis, strong acids.
Hazardous decomposition : Depending on conditions, decomposition products may include the following materials:
products carbon oxides nitrogen oxides Formaldehyde. metal oxide/oxides
Section 11. Toxicological information

Information on toxicological effects
Acute toxicity


Product/ingredient name Result Species Dose Exposure
xylene LD50 Dermal Rabbit 1.7 g/kg -
LD50 Oral Rat 4.3 g/kg -
butan-1-ol LC50 Inhalation Vapor Rat 24000 mg/m³ 4 hours
LC50 Inhalation Vapor Rat 8000 ppm 4 hours
LD50 Dermal Rabbit 3400 mg/kg -
LD50 Oral Rat 790 mg/kg -
diiron trioxide LC50 Inhalation Dusts and mists Rat >5 mg/l 4 hours
LD50 Oral Rat 10 g/kg -
Isopropyl alcohol LC50 Inhalation Vapor Rat 72600 mg/m³ 4 hours
LD50 Dermal Rabbit 12800 mg/kg -
4-methylpentan-2-one LC50 Inhalation Vapor Rat 12.3 mg/l 4 hours
LD50 Dermal Rabbit >5000 mg/kg -
ethylbenzene LC50 Inhalation Vapor Rat 17.8 mg/l 4 hours
LD50 Dermal Rabbit 17.8 g/kg -
toluene LC50 Inhalation Vapor Rat 49 g/m³ 4 hours
LD50 Dermal Rabbit 8.39 g/kg -
Conclusion/Summary : There are no data available on the mixture itself.
Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
xylene Skin - Moderate irritant Rabbit - 24 hours 500 -
mg
Fatty acids, C18-unsatd., Skin - Irritant Human - - -
dimers, oligomeric reaction
products with tall-oil fatty
acids and
triethylenetetramine
Eyes - Severe irritant Rabbit - - -
Conclusion/Summary
Skin : There are no data available on the mixture itself.
Eyes : There are no data available on the mixture itself.
Respiratory : There are no data available on the mixture itself.
Sensitization
Product/ingredient name Route of Species Result
exposure
Fatty acids, C18-unsatd., skin Mouse Sensitizing
acids and
Conclusion/Summary
Skin : There are no data available on the mixture itself.
Respiratory : There are no data available on the mixture itself.


Mutagenicity
Carcinogenicity
Classification
Product/ingredient name OSHA IARC NTP
xylene - 3 -
diiron trioxide - 3 -
Isopropyl alcohol - 3 -
4-methylpentan-2-one - 2B -
ethylbenzene - 2B -
toluene - 3 -
Carcinogen Classification code:
IARC: 1, 2A, 2B, 3, 4
NTP: Known to be a human carcinogen; Reasonably anticipated to be a human carcinogen
OSHA: +
Not listed/not regulated: -
Reproductive toxicity
Teratogenicity
Specific target organ toxicity (single exposure)
Name Category Route of Target organs
exposure
xylene Category 3 - Respiratory tract
irritation
butan-1-ol Category 3 - Respiratory tract
irritation
Category 3 Narcotic effects
Isopropyl alcohol Category 3 - Narcotic effects
4-methylpentan-2-one Category 3 - Respiratory tract
irritation
toluene Category 3 - Narcotic effects
Specific target organ toxicity (repeated exposure)
Name Category Route of Target organs
exposure
ethylbenzene Category 2 - hearing organs
toluene Category 2 - -
Target organs : Contains material which causes damage to the following organs: brain.
Contains material which may cause damage to the following organs: blood, kidneys,
lungs, the nervous system, liver, spleen, upper respiratory tract, skin, central nervous
system (CNS), ears, eye, lens or cornea.
Aspiration hazard


Name Result
xylene ASPIRATION HAZARD - Category 1
ethylbenzene ASPIRATION HAZARD - Category 1
toluene ASPIRATION HAZARD - Category 1
Information on the likely routes of exposure
Potential acute health effects
Eye contact : Causes serious eye damage.
Inhalation : Harmful if inhaled. Can cause central nervous system (CNS) depression. May cause
drowsiness or dizziness. May cause respiratory irritation.
Skin contact : Causes skin irritation. Defatting to the skin. May cause an allergic skin reaction.
Ingestion : Can cause central nervous system (CNS) depression.
Over-exposure signs/symptoms
Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
dryness
cracking
blistering may occur
Ingestion : Adverse symptoms may include the following:
stomach pains
Delayed and immediate effects and also chronic effects from short and long term exposure
Conclusion/Summary : There are no data available on the mixture itself. This product either contains
formaldehyde or is capable of releasing formaldehyde above 0.5 ppm under certain
conditions. Formaldehyde is a known cancer hazard, a skin sensitizer and a respiratory
sensitizer. Exposure to component solvent vapor concentrations in excess of the stated
occupational exposure limit may result in adverse health effects such as mucous
membrane and respiratory system irritation and adverse effects on the kidneys, liver
and central nervous system. Symptoms and signs include headache, dizziness, fatigue,
muscular weakness, drowsiness and, in extreme cases, loss of consciousness.


Solvents may cause some of the above effects by absorption through the skin. There is
some evidence that repeated exposure to organic solvent vapors in combination with
constant loud noise can cause greater hearing loss than expected from exposure to
noise alone. If splashed in the eyes, the liquid may cause irritation and reversible
damage. Ingestion may cause nausea, diarrhea and vomiting. This takes into account,
where known, delayed and immediate effects and also chronic effects of components
from short-term and long-term exposure by oral, inhalation and dermal routes of
exposure and eye contact.
Short term exposure
Potential immediate : There are no data available on the mixture itself.
effects
Potential delayed effects : There are no data available on the mixture itself.
Long term exposure
Potential immediate : There are no data available on the mixture itself.
effects
Potential delayed effects : There are no data available on the mixture itself.
Potential chronic health effects
General : May cause damage to organs through prolonged or repeated exposure. Prolonged or
repeated contact can defat the skin and lead to irritation, cracking and/or dermatitis.
Once sensitized, a severe allergic reaction may occur when subsequently exposed to
very low levels.
Carcinogenicity : Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Mutagenicity : No known significant effects or critical hazards.
Reproductive toxicity : Suspected of damaging fertility or the unborn child.
Numerical measures of toxicity
Acute toxicity estimates
Product/ingredient name Oral (mg/ Dermal Inhalation Inhalation Inhalation
kg) (mg/kg) (gases) (vapors) (dusts and
(ppm) (mg/l) mists) (mg/
l)
AQUAPON Zinc Rich Primer Comp A 2156.4 3283.3 N/A 26.2 3.3
xylene 4300 1700 N/A 11 1.5
butan-1-ol 790 3400 N/A 24 N/A
diiron trioxide 10000 N/A N/A N/A N/A
Isopropyl alcohol 5045 12800 N/A 72.6 N/A
4-methylpentan-2-one 2080 N/A N/A 12.3 1.5
ethylbenzene 3500 17800 N/A 17.8 1.5
toluene 5580 8390 N/A 49 N/A

Section 12. Ecological information

Toxicity
Product/ingredient name Result Species Exposure
butan-1-ol Acute LC50 1376 mg/l Fish 96 hours
Fatty acids, C18-unsatd., EC10 1.78 mg/l Algae 72 hours
acids and
diiron trioxide Acute EC50 >100 mg/l Daphnia 48 hours
Isopropyl alcohol Acute EC50 10100 mg/l Fresh water Daphnia - Daphnia magna 48 hours
4-methylpentan-2-one Acute LC50 >179 mg/l Fish 96 hours
ethylbenzene Acute LC50 150 to 200 mg/l Fresh water Fish 96 hours
Persistence and degradability

Product/ingredient name Test Result Dose Inoculum
4-methylpentan-2-one OECD 301F 83 % - Readily - 28 days - -
Product/ingredient name Aquatic half-life Photolysis Biodegradability

xylene - - Readily
Fatty acids, C18-unsatd., - - Not readily
acids and
4-methylpentan-2-one - - Readily
ethylbenzene - - Readily
toluene - - Readily
Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
xylene 3.16 7.4 to 18.5 low
butan-1-ol 0.88 - low
Isopropyl alcohol 0.05 - low
4-methylpentan-2-one 1.31 - low
ethylbenzene 3.15 79.43 low
toluene 2.73 8.32 low
Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
Disposal should be in accordance with applicable regional, national and local laws and regulations.
Refer to Section 7: HANDLING AND STORAGE and Section 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
for additional handling information and protection of employees. Section 6. Accidental release measures
14. Transport information

DOT IMDG IATA
UN number UN1263 UN1263 UN1263
UN proper shipping PAINT PAINT PAINT
name
Transport hazard class 3 3 3
(es)
Packing group II II II
Environmental hazards No. No. No.
Marine pollutant Not applicable. Not applicable. Not applicable.
substances
Product RQ (lbs) 378.66 Not applicable. Not applicable.
RQ substances (xylene, ethylbenzene) Not applicable. Not applicable.
Additional information
DOT : Package sizes shipped in quantities less than the product reportable quantity are not subject to the
RQ (reportable quantity) transportation requirements.
IMDG : None identified.
IATA : None identified.
Special precautions for user : Transport within user’s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.
Transport in bulk according : Not applicable.

to IMO instruments

Section 15. Regulatory information

United States
United States inventory (TSCA 8b) : All components are active or exempted.
SARA 302/304
SARA 304 RQ : Not applicable.
Composition/information on ingredients
No products were found.
SARA 311/312
Classification : FLAMMABLE LIQUIDS - Category 2
ACUTE TOXICITY (inhalation) - Category 4
SKIN SENSITIZATION - Category 1
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) -
Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2
HNOC - Defatting irritant
Composition/information on ingredients
Name % Classification
xylene ≥20 - ≤28 FLAMMABLE LIQUIDS - Category 3
ACUTE TOXICITY (dermal) - Category 4
EYE IRRITATION - Category 2A
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE)
(Respiratory tract irritation) - Category 3
ASPIRATION HAZARD - Category 1
butan-1-ol ≥20 - ≤24 FLAMMABLE LIQUIDS - Category 3
ACUTE TOXICITY (oral) - Category 4
(Narcotic effects) - Category 3
Fatty acids, C18-unsatd., dimers, ≥10 - ≤20 SKIN IRRITATION - Category 2
oligomeric reaction products SERIOUS EYE DAMAGE - Category 1
with tall-oil fatty acids and SKIN SENSITIZATION - Category 1A
Isopropyl alcohol ≥5.0 - ≤10 FLAMMABLE LIQUIDS - Category 2
4-methylpentan-2-one ≥1.0 - ≤6.4 FLAMMABLE LIQUIDS - Category 2

Section 15. Regulatory information

ethylbenzene ≥1.0 - ≤5.0 FLAMMABLE LIQUIDS - Category 2
SPECIFIC TARGET ORGAN TOXICITY (REPEATED
EXPOSURE) - Category 2
toluene <1.0 FLAMMABLE LIQUIDS - Category 2
SPECIFIC TARGET ORGAN TOXICITY (REPEATED
EXPOSURE) - Category 2
SARA 313
Chemical name CAS number Concentration
Supplier notification : xylene 1330-20-7 10 - 30
butan-1-ol 71-36-3 10 - 30
4-methylpentan-2-one 108-10-1 3-7
ethylbenzene 100-41-4 1-5
SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include
copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
Additional environmental information is contained on the Environmental Data Sheet for this product, which
can be obtained from your PPG representative.
California Prop. 65
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Section 16. Other information

Hazardous Material Information System (U.S.A.)
Health : 3 * Flammability : 3 Physical hazards : 0
( * ) - Chronic effects
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or
risks. Although HMIS® ratings and the associated label are not required on MSDSs or products leaving a facility under 29 CFR 1910.1200, the
preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark
and service mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS®
Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.
National Fire Protection Association (U.S.A.)
Health : 3 Flammability : 3 Instability : 0

Section 16. Other information

Date of previous issue : 2/19/2021
Organization that prepared : EHS
the MSDS
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. ("Marpol" = marine pollution)
N/A = Not available
SGG = Segregation Group
UN = United Nations
Indicates information that has changed from previously issued version.
Disclaimer
The information contained in this data sheet is based on present scientific and technical knowledge. The purpose of this
information is to draw attention to the health and safety aspects concerning the products supplied by PPG, and to
recommend precautionary measures for the storage and handling of the products. No warranty or guarantee is given in
respect of the properties of the products. No liability can be accepted for any failure to observe the precautionary measures
described in this data sheet or for any misuse of the products.

Safety Data Sheet: Section 1. Identification

Uploaded by

Copyright:

Available Formats

Safety Data Sheet: Section 1. Identification

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Safety Data Sheet: Section 1. Identification

Uploaded by

Copyright:

Available Formats

SAFETY DATA SHEET

Date of issue/Date of revision 22 March 2021

Manufacturer : PPG Industries, Inc.

Technical Phone Number : 888-977-4762

Section 2. Hazards identification

United States Page: 1/18

Section 2. Hazards identification

Signal word : Danger

United States Page: 2/18

Section 3. Composition/information on ingredients

Ingredient name % CAS number

SUB codes represent substances without registered CAS Numbers.

Section 4. First aid measures

Most important symptoms/effects, acute and delayed

United States Page: 3/18

Section 4. First aid measures

Indication of immediate medical attention and special treatment needed, if necessary

See toxicological information (Section 11)

Section 5. Fire-fighting measures

United States Page: 4/18

Section 5. Fire-fighting measures

Section 6. Accidental release measures

Methods and materials for containment and cleaning up

United States Page: 5/18

Section 7. Handling and storage

Section 8. Exposure controls/personal protection

United States Page: 6/18

Section 8. Exposure controls/personal protection

United States Page: 7/18

Section 8. Exposure controls/personal protection

Individual protection measures

Section 9. Physical and chemical properties

Section 9. Physical and chemical properties

Section 10. Stability and reactivity

Chemical stability : The product is stable.

Section 11. Toxicological information

United States Page: 9/18

Section 11. Toxicological information

United States Page: 10/18

Section 11. Toxicological information

United States Page: 11/18

Section 11. Toxicological information

United States Page: 12/18

Section 11. Toxicological information

United States Page: 13/18

Section 12. Ecological information

Persistence and degradability

Product/ingredient name Aquatic half-life Photolysis Biodegradability

United States Page: 14/18

Section 13. Disposal considerations

14. Transport information

Transport in bulk according : Not applicable.

United States Page: 15/18

Section 15. Regulatory information

United States Page: 16/18

Section 15. Regulatory information

Section 16. Other information

United States Page: 17/18

Section 16. Other information