Scribd
Upload
363 views4 pages

Packet Tracer Lab 3: VLAN and VTP: Network Diagram

This document summarizes a Packet Tracer lab activity on configuring VLANs and VTP on a network of 4 switches. The objectives are to configure one switch as a VTP server, the other 3 as clients in the "TESTDOMAIN" domain. VLANs 10 named "STUDENTS" and 50 named "SERVERS" need to be created on the server and propagated to all switches. Trunk links between the switches also need to be configured. Step-by-step instructions are provided on carrying out these configurations to demonstrate VLAN and VTP propagation in the network.

Uploaded by

john
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
363 views4 pages

Packet Tracer Lab 3: VLAN and VTP: Network Diagram

This document summarizes a Packet Tracer lab activity on configuring VLANs and VTP on a network of 4 switches. The objectives are to configure one switch as a VTP server, the other 3 as clients in the "TESTDOMAIN" domain. VLANs 10 named "STUDENTS" and 50 named "SERVERS" need to be created on the server and propagated to all switches. Trunk links between the switches also need to be configured. Step-by-step instructions are provided on carrying out these configurations to demonstrate VLAN and VTP propagation in the network.

Uploaded by

john
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Packet Tracer lab 3 : VLAN and VTP

 Last Updated: Monday, 19 August 2019 20:43


 Published: Tuesday, 07 September 2010 20:11
 Written by PacketTracerNetwork

Network diagram
The aim of this lab is to test your ability to configure VLAN and VTP on a small network of 4 switches
using Packet Tracer 7.2.1.

This lab will help you to prepare the VTP testlet and simlet questions of the Cisco ICND1 exam.

Lab instructions
1.Configure the VTP-SERVER switch as a VTP server

2.Connect to the 3 other switches and configure them as VTP clients.


All links between swiches must be configured as trunk lines.

3.Configure VTP domain name as "TESTDOMAIN" and VTP password as "cisco"

4.Configure VLAN 10 with name "STUDENTS" and VLAN 50 with name "SERVERS"

5. Check propagation on all switches of the VTP domain.

VLAN and VTP lab solution


1. Configure the VTP-SERVER switch as a VTP server

VTP-SERVER(config)#vtp mode server

Verify the VTP operating mode using the show vtp status command


VTP-SERVER#show vtp status

VTP Version : 2

Configuration Revision : 4

Maximum VLANs supported locally : 255

Number of existing VLANs : 7

VTP Operating Mode : Server

VTP Domain Name : TESTDOMAIN

VTP Pruning Mode : Disabled

VTP V2 Mode : Disabled

VTP Traps Generation : Disabled

MD5 digest : 0xAE 0x4F 0x3F 0xC5 0xD3 0x41 0x9C 0x11

Configuration last modified by 192.168.1.1 at 3-1-93 00:27:41

Local updater ID is 192.168.1.1 on interface Vl1 (lowest numbered VLAN interface found)

 
2. Connect to the 3 other Catalyst switches and configure them as VTP clients.
All links between swiches must be configured as trunk lines.

VTP-CLIENT3(config)#vtp mode client

VTP-CLIENT3(config)#vtp mode client

Verify the VTP operating mode of the switch using the show vtp status command. The "VTP Operating
Mode" shoud have the"Client" value. Example with VTP-CLIENT3 switch is provided below.

VTP-CLIENT3#sh vtp status

VTP Version : 2

Configuration Revision : 4

Maximum VLANs supported locally : 255

Number of existing VLANs : 7

VTP Operating Mode : Client

VTP Domain Name : TESTDOMAIN

VTP Pruning Mode : Disabled

VTP V2 Mode : Disabled

VTP Traps Generation : Disabled

MD5 digest : 0xAE 0x4F 0x3F 0xC5 0xD3 0x41 0x9C 0x11

Configuration last modified by 192.168.1.1 at 3-1-93 00:27:41


 
Configure each link between switches as a trunk line using the switchport mode truink command

interface GigabitEthernet1/1

switchport mode trunk

interface GigabitEthernet1/2

switchport mode trunk

3. Configure VTP domain name as "TESTDOMAIN" and VTP password as "cisco"

On the VTP server Catalyst switch:

VTP-SERVER(config)#vtp domain TESTDOMAIN

VTP-SERVER(config)#vtp password cisco

On each VTP client switch :

VTP-CLIENT1(config)#vtp password cisco

VTP-CLIENT1(config)#vtp domain TESTDOMAIN

 
4. Configure VLAN 10 with name "STUDENTS" and VLAN 50 with name "SERVERS"

On the VTP server Catalyst 2960 switch, configure the following commands to create both
"STUDENTS" and "SERVERS" vlans :

VTP-SERVER(config)#vlan 10

VTP-SERVER(config-vlan)#name STUDENTS

VTP-SERVER(config)#vlan 50

VTP-SERVER(config-vlan)#name SERVERS

 
5. Check propagation of both "STUDENTS" and "SERVERS" vlans on all Catalyst 2960 network
switches of the VTP domain.

Use the show vlan brief on each switch to check propagation of the 2 VLANS.

VTP-SERVER#show vlan brief

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4, [...]


10 STUDENTS active

50 SERVERS active

1002 fddi-default active

1003 token-ring-default active

1004 fddinet-default active

1005 trnet-default active

Published by Packet Tracer Network.

You might also like