Scribd
Upload
41 views4 pages

Final Assignment - M&I-Sec C

This document provides instructions for a final assignment on measurement and instrumentation. It consists of 3 questions worth a total of 20 marks. Question 1 involves deriving mathematical expressions for parameters of a potential transformer, including its ratio and phase angle. Question 2 involves developing Lissajous patterns based on different frequency and amplitude ratios of X and Y axis signals. Question 3 involves solving two problems: one on a current transformer's primary current and error calculations, and another on electrical strain gauges in a bridge circuit. Students are instructed to show working, take photos of their work, and submit a single PDF file by the deadline.

Uploaded by

Elisabeth Burnett Martin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
41 views4 pages

Final Assignment - M&I-Sec C

This document provides instructions for a final assignment on measurement and instrumentation. It consists of 3 questions worth a total of 20 marks. Question 1 involves deriving mathematical expressions for parameters of a potential transformer, including its ratio and phase angle. Question 2 involves developing Lissajous patterns based on different frequency and amplitude ratios of X and Y axis signals. Question 3 involves solving two problems: one on a current transformer's primary current and error calculations, and another on electrical strain gauges in a bridge circuit. Students are instructed to show working, take photos of their work, and submit a single PDF file by the deadline.

Uploaded by

Elisabeth Burnett Martin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Measurement & Instrumentation

Section: All Semester: Fall 2020-21 Full marks: 20

Final Assignment (Theory)


1) Derive the mathematical expression of the following parameters of a Potential Transformer (PT)
with appropriate phasor diagram: [5.0+2.0 =7.0]
(i) Transformer ratio (R) and
(ii) Phase angle (𝜃)

2) Develop the Lissajous Patterns (a) if Ratio of Y-axis to X-axis signal frequency is 4:3.
Consider the same amplitude for the both Y-axis and X-axis signal. (b) Y-axis voltage
magnitude is twice X-axis voltage magnitude and are in phase. [1.5 x 2= 3.0]

3) Solve the following problems: [5.0 x 2 =10.0]


a) A bar-type CT has 420 turns in the secondary winding. An ammeter connected to the secondary has
a resistance of 1 Ω and reactance of 1.3 Ω, and the secondary winding impedance is (0.8 + j0.8) Ω.
The magnetizing MMF requirement for the core is 80 A-turns and to supply the iron loss the current
required is 25 A. Find the primary winding current and also determine the ratio error when the
ammeter in the secondary winding shows 7A.
Also determine the phase angle error. What type of modification is needed in the ammeter
construction to reduce the phase angle error?

b) Two electrical strain gauge resistances bonded to a Duralumin cantilever and are connected into a
bridge circuit. Each gauge has a resistance of 120Ω. The strain gauge resistances are subjected to a
stress of 110 MN/m2. If the modulus of elasticity of steel is 180 GN/m2, calculate (a) the output
voltage if the detector has a resistance of 9kΩ. (b) the resistance of the detector if 25µA current is
flowing through it. Given that, the gauge factor is 1.8.

Follow the instructions on the next pages for proper submission.


Department of Electrical and Electronic Engineering (EEE)
Faculty of Engineering (FE)
American International University- Bangladesh (AIUB)

Measurement and Instrumentation


Fall 2020-21

Final Assignment (Theory) Serial No.


(Find your SL. no. at the end)

Submitted by:
Student Name:

Student ID: - -
Section:
Instructions for Quiz Submission:
Step 1: Fill the previous page of this assignment and Take picture (as your
Assignment cover page) while preparing the PDF file for submission. You
can find your serial No. at the end. Example: below

Step 2: Take all the pictures of your solutions (from A4 page/exercise


book etc.) and Convert all pictures (step 1+2) into a PDF file.

Step 3: Save the PDF as per following file name format.

Format of PDF file: FA-<ID> Marks might be deducted


if you don’t follow this
example: FA-18-39567-3 filename format

Step 4: Click/Go to the following link and Upload your final term
assignment pdf file on/before 25th December 11:30 pm

https://docs.google.com/forms/d/e/1FAIpQLSeeG32xoyZQ3vo1GDw1e
KZFs0p4u2B2akfMDCAMqPJD1HDW2A/viewform?usp=pp_url
Serial No. (Section: C)
SL# Student ID Name
1 17-33899-1 MIAH, MD. ARMAN
2 18-36082-1 AZIZ, ABDUL
3 18-36109-1 HOSSAIN, MOHAMMED SHAKAWATH
4 18-36195-1 SAZID, SHAHNAWAZ
5 18-36241-1 SAHA, ANIK
6 18-36247-1 ISLAM, MD. NAJMUL
7 18-36252-1 ALAM, MD.
8 18-36261-1 HOSSAIN, TANVIR
9 18-36297-1 RASHEDUZZAMAN, A.H.M
10 18-36351-1 FERDAUS, KAZI ASHIK-UL
11 18-36470-1 RAHMAN, FARIHA
12 18-36849-1 RIMON, MD. NUR ISLAM
13 18-36852-1 MUKSITUZZAMAN, MOHAMMAD TASIN
14 18-36891-1 RAHMAN, ARAF
15 18-36901-1 SHIHAB, KH. ZAHID HASSAN
16 18-36928-1 KAYES, SHAKIYEN
17 18-36973-1 TASNIM, AFSARA
18 18-37017-1 DEY, RATUL
19 18-37068-1 SARKAR, APURBA
20 18-37071-1 BARUA, KAUSHIK
21 18-37106-1 GOSWAMI, NILOY
22 18-37365-1 TARUN, MD.RAZAUL KARIM
23 18-37389-1 PURNENDU, PRODIP KUMAR SAHA
24 18-37476-1 HASSAN, MD.SABBIR
25 18-37498-1 AHMAD, TOUKIR
26 18-37500-1 RAHIM, ABDUR
27 18-38165-2 HASAN, MEHIDI
28 18-38173-2 SAKIB, NAZMUS

You might also like