Test: Oracle X86 Server Installation Specialist Online Assessment

Review your answers, feedback, and question scores below.

This assessment test is the final component of the X86 Server Installation Specialist training. This assessment will allow
you to test your knowledge of the information learned from the X86Server Installation Specialist guided learning path.
Passing with a >80% score from this assessment makes you eligible to become an X86 Server Installation Specialist.

Oracle Server X7-2L and X7-2 Assessment

(Answer all questions in this section)

1. What chip is used for the X7-2 and X7-2L Service Processor?
 Mark for Review 
(1) Points

AST2000

AST2100

Pilot 3

Pilot 4

Correct !

2. Which command accesses the shell where hwdiag can be accessed?

 Mark for Review 
(1) Points

start /sp/diag/shell

access /sp/hwdiag

access /sp/diag/shell

start /sp/hwdiag

Correct !

3. How many processors are supported by the Oracle Server X7-2L and X7-2?
 Mark for Review 
(1) Points

2 or 4

1 only

1 or 2

2 only

Correct !

4. Which PCIe slot is used for the HBA that controls the 8 disk slots of the Oracle Server X7-2?
 Mark for Review 
(1) Points

3
 2

Correct !

5. In which document can you find information on backup, restore, or reset of firmware
configurations?  Mark for Review 
(1) Points

ILOM User’s manual

installation guide

service manual

administration guide

Correct !
6. Which
direction  Mark for Review 
is the (1) Points
Oracle
X7-2L
and X7-2
cooled?

front to back

top to bottom

bottom to top

back to front

Correct !

7.  Which server is the predecessor to the Oracle Server X7-2L?

 Mark for Review 
(1) Points

Oracle Server X6-2L

SPARC T5-2

SPARC S7-2

Oracle Server X5-2

Correct !

8.  How many USB3.0 ports exist on the X7-2 and X7-2L servers?
 Mark for Review 
(1) Points

2 - 1x rear, 1x internal

3 - 1x front, 1x rear, 1x internal

 4 - 2x front, 2x rear

6 - 2x front, 2x rear, 2x internal

Correct !

9.  How many NVME switch cards are needed to support all 8 NVME disks on the Oracle
Server X7-2?  Mark for Review 
(1) Points

NVME switch cards are not used on the Oracle Server X7-2

Correct !

10.  Which is the Ethernet configuration supported on the Oracle Server X7-2?
 Mark for Review 
(1) Points

(4) 10-GbE ports

(2) 10-GbE ports or (2) 25-GbE port

(4) 25-GbE ports

(2) 10-GbE ports and (2) 25-GbE ports

Correct !
11. How
many  Mark for Review 
external (1) Points
PCIe
Gen3
slots are
in the
X7-2L?

11

12

Correct !

12.  Which are the ILOM versions that are going to release with the Oracle Servers X7-2L
and X7-2?  Mark for Review 
(1) Points

4.0.0.25 / 4.0.0.27

4.0.0.20 / 4.0.0.22
 4.0.0.15 / 4.0.0.17

4.0.0.10 / 4.0.0.12

Correct !

13.  Which is the height of the Oracle Server X7-2L?

 Mark for Review 
(1) Points

3U

1U

4U

2U

Correct !

14.  Which diagnostic commands have been removed?

 Mark for Review 
(1) Points

SAS expander HWDIAG utilities

ILOM’s i2ctool

UEFIDIAG commands

hwdiag power pciepoktest

Correct !

15.  How many of the 12 disk bay slots on the Oracle Server X7-2L supports NVME disks?
 Mark for Review 
(1) Points

10

12

Correct !
16. Which
server  Mark for Review 
can mix (1) Points
NVME
drives
and SAS
drives
and
which
server
supports
NVME
drives
without
NVME
switch
cards?
Choose
the
correct
pair.

X7-2L / X7-2L

X7-2 / X7-2L

X7-2L / X7-2

X7-2 / X7-2

Correct !

17.  In which document can you find the LED Sequence and states?
 Mark for Review 
(1) Points

ILOM User’s manual

administration guide

service manual

installation guide

Correct !

18.  Which devices on the Oracle Server X7-2L can use RSTe from BIOS?
 Mark for Review 
(1) Points

SATA M.2 flash modules

This is not currently supported

NVME disk drives

SAS disk Drives

Correct !

19.  Which is a BIOS security feature that is available on the Oracle Server X7-2L and
X7-2?  Mark for Review 
(1) Points

Endpoint Security Suite

ProtectTools Security Manager

BootGuard

Secure Boot

Correct !
 20.  Which new hwdiag command displays SPI based FPGA registers?
 Mark for Review 
(1) Points

hwdiag cpu pirom_info

hwdiag cpld spi_global_reg

hwdiag power pciepoktest

hwdiag cpld log read

Correct !
21. Where are
the M.2  Mark for Review 
flash (1) Points
module
supported?

On the Oracle Server X7-2L with both modules on the same mezzanine<br>

Only on the Oracle Server X7-2L

Only on the Oracle Server X7-2

On the Oracle Server X7-2L off a SATA riser

Correct !

22.  Which OS is NOT supported or pending at the initial release of the Oracle Server
X7-2L and X7-2?  Mark for Review 
(1) Points

Oracle Solaris 11.3

Oracle Linux 7

Oracle VM 3.4

SuSE Linux Enterprise Server

Correct !

23.  How many Estes-INT HBAs are needed to support all 12 disk bays on the Oracle
Server X7-2L?  Mark for Review 
(1) Points

Correct !

24.  How many disks does each NVME switch card support?
 Mark for Review 
 (1) Points

Correct !

25.  Which is the maximum memory supported by the Oracle Server X7-2L and X7-2
using 64 MB DIMMs?  Mark for Review 
(1) Points

500 MB

1.5 TB

768 MB

2 TB

Correct !
26. Which
components  Mark for Review 
are available (1) Points
in 4-socket
mode (side
A)? (Select all
that apply)

(Choose all correct answers)

CMOD4-7

Choice SMOD0

DPCC0-3

PSU2-3

Incorrect. Please refer back to the lesson

“Engineering TOI: Oracle Server X7-8".

27.  Which are the PSU redundant groups in the Oracle Server X7-8?
 Mark for Review 
(1) Points

PSU 0 and 1 = group for system A side (SMOD1, CMODs 4-7) PSU 2 and 3
= group for system B side (SMOD0, CMODs 0-3)
PSU 0 and 1 = group for system B side (SMOD1, CMODs 4-7) PSU 2 and 3
= group for system A side (SMOD0, CMODs 0-3)
PSU 0 and 2 = group for system B side (SMOD1, CMODs 4-7) PSU 1 and 3
= group for system A side (SMOD0, CMODs 0-3)
PSU 0 and 1 = group for system B side (SMOD1, CMODs 4-7) PSU 2 and 3
= group for system A side (SMOD0, CMODs 0-3)

Correct !
 28.  In 4-socket configurations which UPI port is disabled?
 Mark for Review 
(1) Points

Port 2

Port 0

Port 3

Port 1

Correct !

29.  Which power configuration is used in the Oracle Server X7-8? (Select all that
apply)  Mark for Review 
(1) Points

(Choose all correct answers)

2+2 configuration in 8S mode

1+1 configuration in 4S mode

Two 1+1 configuration in 8s mode

2+2 configuration in 4S mode

Incorrect. Please refer back to the lesson

“Engineering TOI: Oracle Server X7-8".

30.  Which are the memory population rules for the Oracle Server X7-8? (Select all
that apply)  Mark for Review 
(1) Points

(Choose all correct answers)

All channels should be loaded for maximum performance

All memory banks should have symmetrical loading

Minimum system DIMM count is one

Populate “furthest first, closest last” from socket on each channel

Correct !
31. What is
the  Mark for Review 
Backup (1) Points
#1
Container
in Oracle
Server X7-
8 (4-
socket B-
side)?

/SYS/CMOD1
 /SYS/FIM

/SYS/SMOD1/MB

/SYS/MIDPLANE

Correct !

32.  How many cooling zones does the Oracle Server X7-8 have?
 Mark for Review 
(1) Points

Correct !

33.  Which command is used for checking the status if MBUS?

 Mark for Review 
(1) Points

hwdiag cpld mbus

hwdiag check mbus

hwdiag status mbus

check status mbus

Correct !

34.  Which are the chassis cooling requirements in Oracle Server X7-8? (Select all that
apply)  Mark for Review 
(1) Points

(Choose all correct answers)

CPUs must have a heat-sink

Each drive bay must have a storage device or a drive filler

Each SMOD bay must have an SMOD

Each DPCC must be installed (with or without LP cards). Empty slots must
have a filler panel

Correct !

35.  What is the maximum DIMM count in the Oracle Server X7-8?
 Mark for Review 
(1) Points

96

16
 64

32

Correct !
36. How
many  Mark for Review 
DPCC (1) Points
(Dual
PCIe
Card
Carrier)
are
installed
in an
Oracle
Server
X7-8?

12

16

Correct !

37.  In 8-socket mode, the SP on SMOD1 will be hold in reset, no ILOM user interface
available on it?  Mark for Review 
(1) Points

True

False

Correct !

38.  The BIOS on Oracle Server X7-8 supports which profiles? (Select all that apply)
 Mark for Review 
(1) Points

(Choose all correct answers)

Exalogic

Exadata

SuperCluster

GPS

Incorrect. Please refer back to the lesson “Engineering

TOI: Oracle Server X7-8".

39.  Which components are cold service CRUs?

 Mark for Review 
(1) Points
 CMOD, SMOD, PCIe cards, fan modules, DIMMs, power backup SCAP

CMOD, SMOD, PCIe cards, internal mini-SAS cabling, DIMMs, power supplies

CMOD, SMOD, PCIe cards, internal mini-SAS cabling, DPCCs, power back SCAP

CMOD, SMOD, PCIe cards, internal mini-SAS cabling, DIMMs, power backup
SCAP

Correct !

40.  Where do you find information about diagnostics and troubleshooting? (Select all
that apply)  Mark for Review 
(1) Points

(Choose all correct answers)

X7-8 Service Manual

Security Guide

ILOM User’s Guide

x86 Servers Diagnostics and Troubleshooting Guide

Correct !
41. In 4-socket
mode, the  Mark for Review 
SPs running (1) Points
on both
SMODs will
present
independent
ILOM
interfaces to
user?

True

False

Correct !

42.  Which diagnostics tools are available in Oracle Server X7-8? (Select all that
apply)  Mark for Review 
(1) Points

(Choose all correct answers)

U-Boot

Hwdiag

CheckHW

UEFIdiag

Correct !
 43.  The Oracle Server X7-8 is available in which configurations?
 Mark for Review 
(1) Points

Two 4-socket servers only

One 8-socket or two 4-socket servers or four 1-socket servers

One 8-socket or two 4-socket servers

One 8-socket or four 1-socket servers

Correct !

44.  The chassis mode conversion (4-socket vs. 8-socket) requires host power of
both sides to be completely off.  Mark for Review 
(1) Points

True

False

Correct !

45.  Which components are hot-swappable in the Oracle Server X7-8?

 Mark for Review 
(1) Points

PSUs, fans, DPCC (Dual PCIe Card Carriers), HBA

PSUs, fans, DPCC (Dual PCIe Card Carriers)

PSUs, fans

PSUs

Correct !
46. What are
three items  Mark for Review 
in the EIS (1) Points
Site-Audit
Report are
documented
for all Oracle
hardware?

(Choose all correct answers)

Access Route requirements

Operating System requirements

Facility Power requirements

IP Address requirements

Operating Environment and Cooling requirements

 Correct !

47.  According to the EIS methodology, when issues are uncovered during the Site-
Audit, who should be notified?  Mark for Review 
(1) Points

(Choose all correct answers)

Oracle sales management

Oracle Premier Support

Installation coordinator if applicable

Customer point of contact

Correct!

48.  Which two EIS documents are most useful during the Installation and
Configuration of Oracle Hardware and Software step?  Mark for Review 
(1) Points

(Choose all correct answers)

Operational Handover Agreement

Installation Configuration Plan

DVD

Site-Audit Report

EIS Checklist

Correct!

49.  What are two cautions that should be acknowledged when acclimatizing a
system?  Mark for Review 
(1) Points

(Choose all correct answers)

Avoid unpacking items inside the computer centre (dust/dirt contaminating

filters etc.)
Once powered on the temperature is no longer an issue, as internal cooling
systems commence
The maximum positive or negative temperature gradient that is permitted
for multi-layer<br>boards is approximately 2° C (4° F) per hour.
Powering ON the system will speed the acclimatization process as the heat
from the system will accelerate its warming

Correct!

50.  For safety awareness with respect to grounding, if a system has been modified
after the manufacturer's assembly process, what three recommendations does  Mark for Review 
the EIS Grounding Standard make? (1) Points

(Choose all correct answers)

 Check whether the modification involved any power supplies, distribution
units or wiring?
Determine whether the local electrician can support the installation process

If qualified personnel did not test the safety of the modified system then
proper testing should be requested before Oracle and/or partner personnel
will work on the equipment
If the temperature is below 60 degrees F., warm the room first before
power ON
If modifications involved any power supplies, distribution units or wiring,
did qualified personnel verify that the modification was was correct and did
they test the system to ensure that it doesn't pose any safety hazard?

Incorrect! Please review the course content and try

again.
51. What
should  Mark for Review 
you do if (1) Points
you
believe
you have
found an
error in
an EIS
checklist?

Follow the feedback method on the last page of every checklist: email
[email protected]
Assume that the EIS team is already aware and the next version of the
checklist will be updated
Email Larry Ellison and recommend changes

Submit your concerns to My Oracle Support

Correct!

52.  Why is the rate of temperature change when acclimatizing systems such an
important factor as described in the EIS methodology?  Mark for Review 
(1) Points

Variations in temperature do not have as big an impact as do Service contract

considerations for how long an installation will take
Variations in temperature should not exceed the approved gradient of
approximately 2° C (4° F) per hour, because ignoring this may could lead to
long-term damage (hair-cracks) on the boards
It is actually not relevant or important

Systems should be warmed up and powered ON as quickly as possible to

optimize the installation project timeline

Correct!

53.  Which three statements are true about EIS?

 Mark for Review 
(1) Points

(Choose all correct answers)

 EIS stands for “Enterprise information Standards”

EIS is a quick and dirty process for expediting Oracle system installations

EIS is a methodology designed to address issues before, during and after the
actual hands-on installation of Oracle systems
EIS evolved from the field, is sustained by those closely involved with the
field, and is intended to assist the field
EIS stands for “Enterprise Installation Standards”

Correct!

54.  What are two activities that take place during the System Test step of the EIS
methodology?  Mark for Review 
(1) Points

(Choose all correct answers)

On Solaris-based systems, Oracle's Explorer Data Collector will be run and the
results evaluated with ORAS/CLI from the EIS-DVD
Electrical grounding and environmental assessment

Tests specified in the Test Procedures Plan Plan will be carried performed

Application installation, configuration, and testing

Incorrect! Please review the course content and try

again.

55.  Why should you typically complete the Installation Configuration Plan and create
your Test Procedures Plan at the same time?  Mark for Review 
(1) Points

You should create the Test Procedures Plan after you have completed the
system installation and configuration.
Test Procedures plan is a standard document used in all generic system
installations.
As you work through the system configuration process with your customer,
you should state how you will test key items in the system’s configuration for
having been successfully completed.

Correct!
56. What is the
mission  Mark for Review 
statement (1) Points
for use of
the
Enterprise
Installation
Standards?

To manage communication and resolution of Services Requests in a timely

and customer-friendly manner
To drive the ongoing development and usage of Enterprise Installation
Standards (EIS), resulting in consistent, high quality, and cost effective
installations that speed time to deployment and provide the foundation for
enhanced stability and performance.
To use a methodology for support service that is from the field, created by
the field for the Field.
 To drive consistent best practices for Oracle Services field delivery

Correct!

57.  What should you do with the EIS checklist when an installation project is
complete?  Mark for Review 
(1) Points

Leave the EIS checklist with the customer so that they can re-install when
they need to
Post the EIS checklist and Test Procedures Plan to My Oracle Support under
your customer’s account
Crumple the checklist and throw it in the customer wastepaper bin

Remove the EIS checklist and other confidential Oracle Intellectual Property
from the customer datacenter

Correct!

58.  What if the customer has their own labeling methodology that differs from the
recommended one from EIS?  Mark for Review 
(1) Points

Ignore the customer’s standard and use the EIS standard

Redo cabling throughout the datacenter to meet the EIS standard

Submit a Service Request for Oracle approval on use of the customer

labeling and routing methods
Follow the customer's standard for cable labeling provided it meets with EIS
requirements for identification and port location.

Correct!

59.  What do EIS deliverables define?

 Mark for Review 
(1) Points

EIS deliverables are the Customer Support Identifiers that customers use for
field delivery service after an installation has completed
EIS deliverables are the documents that are left behind with customers after
an installation service is performed
EIS deliverables describe detailed process steps for each phase of the
installation service
EIS deliverables give a high level description of the scope of the EIS
activities for each product or product family

Correct!

60.  What tasks occur during the operational handover phase of the EIS methodology?
 Mark for Review 
(1) Points

(Choose all correct answers)

Document the serial number for the system(s) installed, as well as any
comments pertaining to the installation
Collate the EISdocV4 documents pertaining to this customer installation, and
 product documentation for handover
Provide the customer the 20% installation service rebate that is required
after a successful installation
Obtain customer signatures to successful close project

Incorrect! Please review the course content and try

again.
66. Which four
documents  Mark for Review 
are included (1) Points
as part of
the
Operational
Handover?

(Choose all correct answers)

Installation and Configuration Plan

Site Audit Report

System Documentation

EIS Checklist for the System installed

Test Procedures Plan

MOS Internal Documentation

Incorrect! Please review the course content and try

again.

67.  When should the Site-Audit be performed?

 Mark for Review 
(1) Points

Prior to the completion of the sale, in order to ensure that the customer’s
location is viable
As soon as possible, and certainly prior to delivery of the system

After the system has been acclimatized and is ready for unpacking at the
customer site
As soon as the product has been delivered to the customer

Correct!

68.  What three documents are typically used as part of the EIS Planning and
Preparation stage in the installation process?  Mark for Review 
(1) Points

(Choose all correct answers)

Project Schedule

Test Procedures Plan

Installation and Configuration Plan

Site Audit Report

 Acclimatization Report

Operational Hand-off Form

Correct!

69.  What are the two primary objectives for the Installation Configuration Planning
step of the EIS methodology?  Mark for Review 
(1) Points

(Choose all correct answers)

Oracle/Partner and Customer will determine and mutually agree upon the
hardware and software installation requirements which will be documented
in the Installation and Configuration Plan
Customer provides walk-through of installation site

Tests that will be performed during the Systems Testing will be defined.

Oracle/Partner confirms power and cooling requirements for system

installation

Incorrect! Please review the course content and try

again.

70.  Assuming a SPARC T5 Server installation on which you install Solaris 11, what
EIS documentation, at a minimum, is it recommended that you bring to support  Mark for Review 
you in the installation project? (1) Points

(Choose all correct answers)

EIS Installation Checklist for Solaris 11 OS

EIS Installation Checklist for Common Array Manager

EIS Installation Checklist for Sun Datacenter InfiniBand Switch 36

EIS Installation Checklist for SPARC T5

Incorrect! Please review the course content and try

again.

71. What are
Oracle  Mark for Review 
Standard (1) Points
System
Installations
(OSSI)?

Advanced professional services offered by IBM Global Services

Installation Services sold by 3rd party service providers

Field Delivery Support Services offered through certified partners

Installation Services sold by Oracle Advanced Customer Support

Correct!
72.  Name three of the problems that EIS was created to overcome?
 Mark for Review 
(1) Points

(Choose all correct answers)

Inconsistent installations: Customers buying identical servers for two

locations were dismayed to find different patch levels, firmware versions
etc.
Lack of formal agreement with customers as to outcome of an installation

Standards for delivery of replacement parts for Oracle hardware

Oracle hardware shipping best practices for on-time delivery

Poor communication/use of Best Practices

Correct!

73.  Which four objectives are primary goals for an EIS Site Audit?
 Mark for Review 
(1) Points

(Choose all correct answers)

Determine the floor weight load capacity at the location where the System
will be installed
Determine how many logical domains need to be configured on the system

Determine how frequently system backups will be completed

Determine the availability of required electrical power to run and maintain

the System
Determine installation needs for the System, including such assessments as:
the suitability of access routes to the installation location, such as doors,
elevators, floor strengths and ramps
Determine the environmental conditions at Customer's site including
temperature, humidity, cleanliness and such other assessments as are
determined to be necessary in Oracle's sole discretion

Correct!

74.  Why it is important to do Installation planning, rather than just asking the
customer as you work through the installation process? (Select three)  Mark for Review 
(1) Points

(Choose all correct answers)

Pricing for Installation Services is less expensive if planning in not included

Support Services will not engage on services requests if no installation

planning was done
Customer technical contact may not be readily available

Planning leads to more thoughtful consideration for a predictable outcome

of the installation process
Continuing interruptions can detract from the professionalism of your work,
and lead to customer dissatisfaction

Incorrect! Please review the course content and try

 again.

75.  What is the primary purpose of the EIS-DVD?

 Mark for Review 
(1) Points

The EIS-DVD is to help installers of Oracle/Sun products perform consistent

installations in an efficient manner.
The EIS-DVD is used for on-the-job tutorials on how to install Oracle
servers and storage
The EIS-DVD is an annually released product which support all hardware
installations, and documents all bugs and issues that have been logged
during the prior year
The EIS-DVD is a tool that is provided to installation partners as a give-
away to customers

Correct!
76. What are
the four  Mark for Review 
key points (1) Points
covered in
each test
topic of the
Test
Procedures
Plan?

(Choose all correct answers)

Conclusion

Test Result

Objective

Method

Outcome

Prerequisites

Incorrect! Please review the course content and try

again.

77.  Which Oracle products are covered by EIS Checklists – select all that apply.
 Mark for Review 
(1) Points

(Choose all correct answers)

Servers

ERP applications

OS and Cluster-related Software

Switches

Engineered Systems

Oracle Fusion Middleware

 Storage

Incorrect! Please review the course content and try

again.

78.  Why do the EIS Standards recommend that external cables between Oracle
hardware, such as servers, storage devices, network devices and ports be clearly  Mark for Review 
labeled? (1) Points

Service requests for field diagnostics will not be accepted unless cables are
labeled
Labeling is not an EIS best practice

For ease of maintenance it should be unambiguously clear from the label on

each cable, where the cable has to be attached
Cable routing should be done with rubber bands for ease of reconfiguration

Correct!

79.  What is the primary goal of the Installation and Configuration of Oracle Hardware
and Software step in the EIS methodology?  Mark for Review 
(1) Points

Managing transition from Installation phase to Field Service issue recording

Hardware cabling , wiring and Power ON

Troubleshooting software configuration issues

System acclimatization, installation, and basic configuration

Correct!

80.  Why are EIS deliverables relevant for Partner installations too?
 Mark for Review 
(1) Points

EIS deliverables describe the amount of time, materials and deliverables are
in scope for a standard installation
EIS deliverables provide flexibility when customers want to make ad-hoc
configuration changes
Advanced Customer Services mandates that Partners use the EIS
methodology for installations
When partners use the EIS deliverables and submit documentation to that
effect, their customer gets a 25% discount on support

Correct!
81. What two
activities are  Mark for Review 
accomplished (1) Points
during
Installation
Task Planning
step in the
EIS
Methodology?

(Choose all correct answers)

 Review the timeframe options for delivery of the service

System unpacking and acclimatization

Networking and system component cabling

Communicate schedule for installation to the customer

Organization of the team who will actively work the Installation

Incorrect! Please review the course content and try

again.

82.  What are three types of configuration information typically documented in an

Installation Configuration Plan?  Mark for Review 
(1) Points

(Choose all correct answers)

System host names

IO cards and controllers

Boot Disk Layout

General and Management Network Configuration

System documentation and guidelines

Power cord specifications

Incorrect! Please review the course content and try

again.

83.  What should partners do before first using ESISdocV4? (Select two)
 Mark for Review 
(1) Points

(Choose all correct answers)

Review the Openoffice presentation on EISdoc V4 found on the EIS

Planning & Documentation web page
Review the “EISdoc V4 Getting Started Cookbook” and “Success with
EISdoc V4 Cookbook”
Submit their EIS Test Procedure Plan outcomes

Review Oracle product overview documentation

Correct!

84.  You are assigned to an installation project in France in February to install 5

new SPARC T5 servers. The servers, in their original packaging, are sitting in  Mark for Review 
the customer’s loading dock with a temperature of 8 degrees C (46 degrees F). (1) Points
The customer’s data center is 20 degrees C (68 degrees F). What is the
recommended next step in acclimating these systems?

Unpack the servers and store in the loading dock

Move the systems (still packed) into a room with a similar environment to
 the data center
Unpack the servers and store in the data center

Move the systems (still packed) into the data center

Correct!

85.  Which three responses are true regarding EISdoc v4?

 Mark for Review 
(1) Points

(Choose all correct answers)

Is an OpenOffice-based set of documentation that includes planning for

installations of Oracle equipment and some software
Is available on the partner Enterprise Installations Standards web page
and on the EIS-DVD
Is accessible to customers and end-users of Oracle hardware and software

Contains documents matched to the steps in the EIS Methodology

Is a free guide to configuring Oracle software

Correct!
86. What four
tasks are  Mark for Review 
typically (1) Points
happening
at the EIS
Planning
and
Preparation
stage in the
installation
process?

(Choose all correct answers)

Begin work on Project Schedule

Notification of Customer Installation project

Identify Installation team – Oracle Installation Coordinator, Project Manager,

Customer Point of Contact, others as needed
Compile EIS planning documents

Unpack and power ON systems

Cable and install systems into custom rack

Incorrect! Please review the course content and try

again.

87.  What is the purpose for the Operational Handover step in the EIS Methodology?
 Mark for Review 
(1) Points

Documents how to use the EIS documentation and standards

 Documents the installation and configuration of Customer's system(s)

Perform system testing and diagnostics

Used to negate responsibility for any ongoing System issues

Correct!

88.  What three typical activities are done during the Project Initiation phase of the
EIS Methodology?  Mark for Review 
(1) Points

(Choose all correct answers)

The EIS Site-Audit is scheduled

System delivery occurs, and the project commences

System configuration details are documented.

Details about the project are identified and documented, for example, is this
a single system installation or a complex, multi-product installation
Details about the customer are determined and documented

Incorrect! Please review the course content and try

again.

89.  When should you review deliverables and why?

 Mark for Review 
(1) Points

EIS deliverables are an interim checklist to ensure that at the mid-way point
of an installation the project remains on track.
Ideally EIS deliverables would be reviewed at the very start of an installation
project, as they clearly define scope, roles and responsibilities, and project
deliverables
EIS deliverables are included in the Oracle system shipping and packaging
documents near the start of an installation
EIS deliverables are used as a last step in the installation process to ensure
the installer provided everything that is required

Correct!

90.  Why should you use the EIS methodology to guide your installation process?
 Mark for Review 
(1) Points

Larry Ellison has mandated using EIS

Using the proven EIS methodology will provide step-by-step installation

guidelines, help guarantee a quality installation, make your life easier, and
ensure customer satisfaction
The EIS methodology provides a 20% discount on Support Services if you
install your customers’ hardware or software using it
Installation processes are very lengthy, the EIS methodology is quick and
dirty

Correct!
91. What
is  Mark for
found Review 
on (1) Points
the
EIS-
DVD?
Select
all the
apply.

(Choose all correct answers)

Selected Oracle/Sun Software

Sales and presales technical training on Oracle systems

A complete set all configuration files for every Oracle server, storage system and
Engineered system
Scripts that assist during the installation

Tools to help verify the quality of the installation (e.g. ORAS/CLI)

Correct!

92.  If the customer has asked for some customization of their installation, how is testing
for that accomplished? Choose all responses that apply.  Mark for Review 
(1) Points

(Choose all correct answers)

Oracle is automatically responsible for any non-standard installation procedure,

regardless of whether they were agree to as part of the Installation and
Configuration Plan
Additional tests can be inserted into the Test Procedures plan

Not all installation actions need testing

Testing above and beyond the Covered System Tests are at the sole discretion of
Oracle and/or the Partner installer

Incorrect! Please review the course content and try again.

93.  What is the primary purpose of the”Basic Solaris” standard?

 Mark for Review 
(1) Points

Describes how to install legacy versions of Solaris on systems that need to support
backward compatible applications
Differentiates between Linux and Solaris installation processes on dual-boot
systems
Specifically describes how to install Solaris on non-SPARC hardware

Defines a method for achieving a consistent installation for Oracle Servers with
Solaris OS

Correct!