Scribd
Upload
54 views

Soil Mechanics Laboratory: (3) : Grain Size Analysis - (Sieve Method+ Hydrometer Method)

The document provides details on tests conducted to analyze the grain size of soil samples, including sieve analysis and hydrometer analysis. Sieve analysis was used to determine the distribution of particles larger than 0.075mm. Hydrometer analysis was then used to analyze the fraction finer than 0.075mm. The test data collected included mass retained on each sieve, hydrometer readings over time, and calculations of uniformity coefficient and coefficient of gradation from the results.

Uploaded by

Rana Abdelbaset Bostanji
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
54 views

Soil Mechanics Laboratory: (3) : Grain Size Analysis - (Sieve Method+ Hydrometer Method)

The document provides details on tests conducted to analyze the grain size of soil samples, including sieve analysis and hydrometer analysis. Sieve analysis was used to determine the distribution of particles larger than 0.075mm. Hydrometer analysis was then used to analyze the fraction finer than 0.075mm. The test data collected included mass retained on each sieve, hydrometer readings over time, and calculations of uniformity coefficient and coefficient of gradation from the results.

Uploaded by

Rana Abdelbaset Bostanji
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Mutah University

Engineering Collage
Civil Department

Soil Mechanics Laboratory

Tests Name:
(3): GRAIN SIZE ANALYSIS –(SIEVE METHOD+
HYDROMETER METHOD)

Student Name: Rana Abdelbaset Bostanji

Tests Day/Date: Tuesday (2:00-5:00)

Dr: Mohammed S. Al-Zoubi


Eng: Wafaa A. AL-sihaimat
1-Sieve Analysis:
Introduction:
In order to classify ai soil for engineering purposes, one needs to know the distribution of the
size of grains in a given soil mass. Sieve analysis is a method used to deter mine the grain-
size distribution of soils Sieves are made of woven wires with square openings. Note that as
the sieve number increases the size of the openings decreases.

Equipment:
1. Sieves, a bottom pan, and a cover
-Note: Sieve numbers 4, 10, 20, 40, 60, 140, and 200 are generally used for most standard
sieve analysis work.
2. A balance sensitive up to 0.1 g
3. Mortar and rubber-tipped pestle·
4. - Oven 5. Mechanical sieve shaker

Procedure:
1. Collect a representative oven dry soil sample. Samples having largest particles of the size
of No. 4 sieve openings (4.75 mm) should be about 500 grams. For soils having largest
particles of size greater than 4.75 mm, larger weights are needed.

2. Break the soil sample into individual particles using a mortar and a rubber-tipped pestle.
(Note: The idea is to break up the soil into individual particles, not to break the particles
themselves.)

3. Determine the mass of the sample accurately to 0.1 g (W).

4. Prepare a stack of sieves. A sieve with larger openings is placed above a sieve with smaller
openings. The sieve at the bottom should be No. 200. A bottom pan should be placed under
sieve No. 200. As mentioned before, the sieves that are generally used in á stack are Nos. 4,
10, 20, 40, 60, 140, and 200; however, more sieves can be placed in between.

5. Pour the soil prepared in Step 2 into the stack of sieves from the top.

6. Place the cover on the top of the stack of sieves.

7. Run the stack of sieves through a sieve shaker for about 10 to 15 minutes.

8. Stop the sieve shaker and remove the stack of sieves.

9. Weigh the amount of soil retained on each sieve and the bottom pan

10. fa considerable amount of soil with silty and clayey fractions is retained on the No 200
sieve, it has to be washed. Washing is done by taking the No. 200 sieve with the soil retained
on it and pouring water through the sieve from a tap in the laboratory.
TEST DATA:
Sieve analysis data:

Mass of oven dry test sample=850 g


Sieve mass retained Percent of mass
Sieve Cumulative percent
opening. on each retained on each %finer
NO. retained
(mm) sieve(g) sieve
32.1
4 4.75 32.1 = 3.776 3.776 100 − 3.776 = 96.224
850
10 2.00 37.5 4.411 3.776 + 4.411 = 8.187 91.813
20 0.840 43.6 5.129 13.316 86.684
40 0.425 36.1 4.247 17.563 82.437
50 0.300 39 4.588 22.151 77.849
100 0.150 40 4.705 26.856 73.144
200 0.075 16.5 1.941 28.797 71.203
pan --- 605.2 71.2 99.997 0.003
Sum=850

Graph:
-Hydrometer Analysis:
Introduction:
Hydrometer analysis is the procedure generally adopted for determination of the particle-size
distribution in a soil for the fraction that is finer than No. 200 sieve size (0.075 mm). The lower limit
of the particle-size determined by this procedure is about 0.001 mm.
Equipment:
1. ASTM 152-H hydrometer
2. Mixer
3. Two l000-cc graduated cylinders.
4. Thermometer
5. Constant temperature bath
6. Deflocculating agent
7. Spatula
8. Beaker
9. Balance
10. Plastic squeeze bottle
11. Distilled water
12. No. 12 rubber stopper

Procedure:
Note: This procedure is used when more than 90 per cent of the soil is finer than No. 200 sieve.
1. Take 50 g of oven-dry, well-pulverized soil in a beaker.
2. Prepare a deflocculating agent. Usually, a 4% solution of sodium hexametaphosphate (Calgon) is used. This
can be prepared by adding 40 g of Calgon in 1000 cc of distilled water and mixing it thoroughly.,
3. Take 125 cc of the mixture prepared in Step 2 and add it to the soil taken in Step 1. This should be allowed
to soak for about 8 to 12 hours.
4. Take a I1000-cc graduated cylinder and add 875 cc of distilled water plus 125 cc of deflocculating agent in
it. Mix the solution well.
5. Put the cylinder (from Step 4) in a constant temperature bath. Record the temperature of the bath, T (in 0c).
6. Put the hydrometer in the cylinder (Step 5). Record the reading. (Note: The top a/the meniscus should be
read.) This is the zero correction (Fz), which can be +ve or -ve. Also observe the meniscus correction (F m).
7. Using a spatula, thoroughly mix the soil prepared in Step 3. pour it into the mixer cup. Note: During this
process, some soil may stick to the side of the beaker. Using the plastic squeeze bottle filled with distilled
water, wash all the remaining soil in the beaker into the mixer cup.
8. Add distilled water to the cup to make it about two-thirds full. Mix it for about two minutes using the mixer.
9. Pour the mix into the second graduated 1000-cc cylinder. Make sure that all of the soil solids are washed
out of the mixer cup. Fill the graduated cylinder with distilled water to bring the water level up to the 1000-cc
mark.
10. Secure a No. 12 rubber stopper on the top of the cylinder (Step 9). Mix the soil-water well by turning the
soil cylinder upside down several, times.
11. Put the cylinder into the constant temperature bath next to the cylinder described in Step 5. Record the
time immediately. This is· cumulative time t= O. Insert the hydrometer into the cylinder containing the soil-
water suspension.
12. Take hydrometer readings at cumulative times t = 0.25 min., 0.5 min., 1 min., and 2 min. Always read the
upper level of the meniscus.
13. Take the hydrometer out after two minutes an<l put it into the cylinder next to it (Step5).
14. Hydrometer readings are to be taken at time t = 4 min., 8 min., 15 min., 30 min., 1
hr., 2 hr., 4 hr., 8 hr., 24 hr. and 48 hr. For each reading, insert the hydrometer into
the cylinder containing the soil-water suspension about 30 seconds before the reading.
is due. After the reading is taken, remove the hydrometer and put it back into the
cylinder next to it (Step 5).
Hydrometer analysis data:

Zero correction,
FZ=+7.0
Control sieve No.200
Gs of solids =2.75
Mass of dry soil=50.0
g
Meniscus, Fm=1

Elapsed time, Temp. Act. Adj.


R FT Rcp RCL L A D
min ,0C %Finer %Finer
0.3 22 55 0.65 48.65 95.345 28.606 56 7.3 0.0129 0.0636
0.5 22 54 0.65 47.65 93.394 28.018 55 7.44 0.0129 0.0497
1.0 22 53 0.65 46.65 91.434 27.430 54 7.6 0.0129 0.0355
2.0 22 43 0.65 36.65 71.834 21.550 44 9.1 0.0129 0.0275
3.0 22 38 0.65 31.65 62.034 18.610 39 9.9 0.0129 0.0234
4.0 22 35 0.65 28.65 56.154 16.846 36 10.4 0.0129 0.0208
8.0 22 30 0.65 23.65 46.354 13.906 31 11.2 0.0129 0.0152
15.0 22 28 0.65 21.65 42.434 12.730 29 11.5 0.0129 0.0112
30.0 22 27 0.65 20.65 40.474 12.142 28 11.7 0.0129 0.0080
60.0 22 18 0.65 11.65 22.934 6.850 19 13.2 0.0129 0.0060
120.0 22 14 0.65 7.65 14.994 4.498 15 13.8 0.0129 0.0043
240.0 19 10 -0.1 2.9 5.684 1.705 11 14.5 0.0134 0.0032
800.0 19 8 -0.1 0.7 1.372 0.411 9 14.8 0.0134 0.0018
-Show Clear Sample Calculation and Discussion:
--FT=-4.85+0.25T=-4.85+0.25*22=0.65
--Rcp =R+ FT - FZ =55+0.65-7.0=48.65
𝑎𝑅𝑐𝑝 0.98×48.65
--Present Finer(Act.) = = × 100 = 95.354
𝑊𝑠 50
𝑇𝑎𝑏𝑙𝑒 5 − 3 → 𝐺𝑠 = 2.75 𝑠𝑜 𝑎 = 0.98
30 30
--Present Finer (Adj.) =(Act. % finer)× = 95.345 × = 28.606
100 100
--Rcl=R+Fm=55+1=56
--L and A from Table
𝐿 7.3
--𝑫 = 𝐴√𝑡 = 0.0129√0.3 = 0.0636

Graph :
Calculations:
𝑫𝟔𝟎 𝟎.𝟎𝟐𝟑
uniformity coefficient (Cu) = = = 𝟓. 𝟕𝟓
𝑫𝟏𝟎 𝟎.𝟎𝟎𝟒
𝑫𝟐𝟑𝟎 𝟎.𝟎𝟎𝟕𝟐
coefficient of gradation (Cc ) = = = 𝟎. 𝟓𝟑
𝑫𝟔𝟎 ×𝑫𝟏𝟎 𝟎.𝟎𝟐𝟑×𝟎.𝟎𝟎𝟒

A grain-size distribution plot-combined results from


-

sieve analysis and hydrometer analysis.

You might also like