Ag Mech Semester Exam

Name: Robert Nevling
Date: 12/18/19
Final Exam Ag Mech
Multiple Choice
1. What is used to change voltage?

a. Rectifier
b. Transformer
c. Step up transformer
d. Step down transformer
2. Which of the following changes voltage for a house so that the electricity is useable?
a. Rectifier
b. Transformer
c. Step up transformer
d. Step down transformer
3. The path through which electricity flows is known as what?
a. Hot wire
b. Neutral wire
c. Circuit
d. Closed circuit
4. Which of the following is a complete circuit?
a. Open circuit
b. Closed circuit
c. Circuit
d. IDN
5. What wire carries electrical pressure to the load?
a. Hot wire
b. Neutral wire
c. Ground wire
d. A wire
6. What wire carries electrical pressure from the load to the source?
a. Hot wire
b. Neutral wire
c. Ground wire
d. A wire
7. What wire carries stray voltage to the earth?
a. Hot wire
b. Neutral wire
c. Ground wire
d. A wire
8. The rate at which electric current flows through a circuit is known as which of the
following?
a. Amperes
b. Amperage
c. Voltage
d. Volts
9. Pressure available in an energized circuit whether or not it is being used is known as
which of the following?
a. Amperes
b. Amperage
c. Voltage
d. Volts
True False
10. True or False. All current flows through each item in the circuit in a series circuit.
11. True or False. The same current flows through each load in a parallel circuit.
12. True or False. The current only has one path to flow in a series circuit.
13. True or False. Removing a device from a series circuit has no effect on other devices.
14. True or False. Current is divided evenly in a parallel circuit.
15. True or False. Removing any device in a series circuit will stop the flow of electricity.
Short answer. Define the following terms:
16. Measurement
a. the size, length, or amount of something
17. Weight
a. omit
18. Volume
a. the amount of space an object takes up
19. Level
a. a flat horizontal surface
20. Plumb
a. a flat vertical surface
21. Tare
a. a reset in the calculation of the weight
22. Calibrate
a. making fine adjustments to ensure a measuring device is accurate
23. Tolerance
a. the capability to endure something
24. Measurement is the process of determining which of the following?
a. The qualitative value of an item or substance
b. The quantitative size or amount of an item
c. The subjective merit of an item or substance
d. The objective utility or capacity of an item
25. Amount of three-dimensional space is measured through which of the following?
a. Weight
b. Distance
c. Density
d. Volume
26. Which of the following is a unit of temperature measurement?
a. Hectoliter
b. Ton
c. Barrel
d. Kelvin
27. How many quarts are in a gallon?
a. 2 quarts
b. 4 quarts
c. 6 quarts
d. 8 quarts
28. A caliper is used to measure which of the following?
a. Weight
b. Distance
c. Temperature
d. Volume
29. The presentation recommends doing which of the following when using a tape measure?
a. Holding the tape level or plumb
b. Letting the tape sag just a little
c. Angling the tape across the material being measured
d. Working with a customary/metric tape
30. Where does the presentation recommend placing a measuring cup when using it to
measure a substance?
a. On an organic surface
b. On a surface above eye level
c. On a flat, even surface
d. On a metallic surface
31. The process of making fine adjustments to ensure a measuring device is accurate is
known as which of the following?
a. Taring
b. Tolerating
c. Customizing
d. Calibrating
32. How many feet are in a mile?
a. 5,280ft
33. How many square feet are in an acer?
a. 43,560sf
34. How many acers are in a section?
a. 640
35. How big is a section?
a. __________________________________________________________________
__________________________________________________________________
36. As shown in the presentation, which of the following is the pipe size used for the main
cold water supply?
a. 3/4 inch
b. 1/2 inch
c. 1/4 inch
d. 1/3 inch
37. Which of the following pieces of equipment supplies pressure and heats the Coldwater
supply?
a. Sink
b. Faucet
c. Water heater
d. PEX Pipe
38. As shown in the presentation, which type of fitting is used to supply cold-water tithe sink
and toilet from the main water supply line?
a. 90 degree fitting
b. Tee fitting
c. Push to connect fitting
d. Reducer fitting
39. When installing a drain line, how many inches should the drain line be installed off the
floor?
a. 18 inches
b. 8 inches
c. 24 inches
d. 20 inches
40. When installing water supply lines, how many inches should the water lines be installed
off the floor?
a. 12 inches
b. 10 inches
c. 18 inches
d. 21 inches
41. How many inches apart should water supply lines be installed?
a. 12 inches
b. 6 inches
c. 4 inches
d. 8 inches
42. Where should the hot water line be installed?
a. On the right side of the cold water line
b. On the left side of the cold water line
c. Underneath the cold water line
d. Above the cold water line
43. Which of the following is used to turn off the water pressure from the water heater and
the hot water system?
a. PEX pipe
b. Ring connector
c. PEX washer
d. Shut-off valve
44. Which of the following is installed on the ends of the water supply lines during the “stub
out” phase of installation?
a. PEX pipe
b. PVC elbow
c. Elbow stub out
d. Shut-off valve
Use the diagram and word bank to answer the following questions.
45. ____________________________
46. ____________________________
47. ____________________________
48. ____________________________
49. ____________________________

Ag Mech Semester Exam

Uploaded by

Copyright:

Available Formats

Ag Mech Semester Exam

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ag Mech Semester Exam

Uploaded by

Copyright:

Available Formats

Name: Robert Nevling

Final Exam Ag Mech

1. What is used to change voltage?

You might also like