Scribd
Upload
341 views

Source Code Esp32 DC Motor

1. The document contains code for controlling two DC motors using Bluetooth on an ESP32 microcontroller. 2. It initializes the PWM, motor pins, and Bluetooth module. 3. It then enters a loop where it reads data from Bluetooth, interprets the data to determine motor direction and speed, and controls the motors accordingly by changing the pin states and PWM duty cycles.

Uploaded by

zero ok
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
341 views

Source Code Esp32 DC Motor

1. The document contains code for controlling two DC motors using Bluetooth on an ESP32 microcontroller. 2. It initializes the PWM, motor pins, and Bluetooth module. 3. It then enters a loop where it reads data from Bluetooth, interprets the data to determine motor direction and speed, and controls the motors accordingly by changing the pin states and PWM duty cycles.

Uploaded by

zero ok
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

1 /*

2 * Handoko Muji Prabowo


3 * NIM :
4 * Teknik Otomasi
5 */
6
7 #include "BluetoothSerial.h"
8 #include <analogWrite.h>
9
10 BluetoothSerial ESP_BT;
11
12 byte dataDiterima;
13 int duttyCycle = 200;
14
15 //Motor A
16 int motor1Pin1 = 27; //Pin 27
17 int motor1Pin2 = 26; //Pin 26
18 int enable1Pin = 14; //Pin 14 untuk konrol speed PWM
19
20 //Motor B
21 int motor2Pin1 = 25; //Pin 25
22 int motor2Pin2 = 33; //Pin 33
23 int enable2Pin2 = 32; //Pin 32 untuk konrol speed PWM
24
25 void setup() {
26 // put your setup code here, to run once:
27 //Setting PWM
28 analogWriteFrequency(30000); //Setting PWM frek di 3Khz
29 analogWriteResolution(8); // Timer resolusi nya 8 BIT
30 //setting pin sebagai output
31 pinMode(motor1Pin1, OUTPUT);
32 pinMode(motor1Pin2, OUTPUT);
33 pinMode(enable1Pin, OUTPUT);
34 pinMode(motor2Pin1, OUTPUT);
35 pinMode(motor2Pin2, OUTPUT);
36 pinMode(enable2Pin2, OUTPUT);
37
38 //Setting Pin Output LOW
39 digitalWrite(motor1Pin1, LOW);
40 digitalWrite(motor1Pin2, LOW);
41 digitalWrite(motor2Pin1, LOW);
42 digitalWrite(motor2Pin2, LOW);
43
44 //Siapkan Koneksi Bluetooth Serial
45 Serial.begin(9600);
46 ESP_BT.begin("ESP32_KONTROL_MOTOR"); // Nama Bluetooth
47 Serial.println("Perangkat Bluetooth siap di sambungkan");
48
49 //Testing
50 Serial.print("Testing DC Motor...");
51 }
52
53 void loop() {
54 // put your main code here, to run repeatedly:
55 if(ESP_BT.available()){ // Cek bila ada koneksi bluetooth
56 dataDiterima = ESP_BT.read(); // Data yang di kirim kan dari hp akan di tampung
di variabel dataDiterima
57 Serial.print("Diterima:"); Serial.println(dataDiterima);
58
59 if(dataDiterima == 48){ // bila data dari hp sebuah bilangan 0 maka TRUE
60 //MOTOR MAJU SPEED MAX
61 analogWrite(enable1Pin, 255);
62 analogWrite(enable2Pin2, 255);
63 Serial.println("MOTOR MAJU");
64 digitalWrite(motor1Pin1, LOW);
65 digitalWrite(motor1Pin2, HIGH);
66 digitalWrite(motor2Pin1, LOW);
67 digitalWrite(motor2Pin2, HIGH);
68 delay(2000);
69
70 // Stop DC motor
71 Serial.println("MOTOR STOP");
72 digitalWrite(motor1Pin1, LOW);
73 digitalWrite(motor1Pin2, LOW);
74 digitalWrite(motor2Pin1, LOW);
75 digitalWrite(motor2Pin2, LOW);
76 delay(1000);
77 }
78
79 if(dataDiterima == 49){ // bila data dari hp sebuah bilangan 1 maka TRUE
80 //MOTOR MUNDUR SPEED MAX
81 analogWrite(enable1Pin, 255);
82 analogWrite(enable2Pin2, 255);
83 Serial.println("MOTOR MUNDUR");
84 digitalWrite(motor1Pin1, HIGH);
85 digitalWrite(motor1Pin2, LOW);
86 digitalWrite(motor2Pin1, HIGH);
87 digitalWrite(motor2Pin2, LOW);
88 delay(2000);
89
90 // Stop the DC motor
91 Serial.println("MOTOR STOP");
92 digitalWrite(motor1Pin1, LOW);
93 digitalWrite(motor1Pin2, LOW);
94 digitalWrite(motor2Pin1, LOW);
95 digitalWrite(motor2Pin2, LOW);
96 delay(1000);
97 }
98
99 if(dataDiterima == 50){ // bila data dari hp sebuah bilangan 2 maka TRUE
100 digitalWrite(motor1Pin2, LOW);
101 digitalWrite(motor2Pin1, HIGH);
102 digitalWrite(motor1Pin1, HIGH);
103 digitalWrite(motor2Pin2, LOW);
104 while(duttyCycle <= 255){ // bila duttycycle = 255 maka loop berakhir
105 analogWrite(enable1Pin, duttyCycle); // kontrol speed perlahan - perlahan
dari 200-255 untuk enable1Pin
106 analogWrite(enable2Pin2, duttyCycle); // // kontrol speed perlahan -
perlahan dari 200-255 untuk enable2Pin2
107 Serial.print("Maju dengan duty cycle: ");
108 Serial.println(duttyCycle);
109 duttyCycle = duttyCycle + 5; // proses increment
110 delay(500);
111 }
112 duttyCycle = 200; // setelah loop maka variable di reset ke 200
113 }
114 }
115 }
116

You might also like