For the latest prices, please check AutomationDirect.com.

1-800-633-0405

Ethernet Analog PLC

C0-12DRE-1-D $203.00
4 DC Input (Sink/Source)/4 Relay Output
4 Analog Current Input
2 Analog Current Output Micro PLC

Wiring Diagram
C0-12DRE-1-D
24VDC
C1
X1

+
X2 See Discrete I/O Specifications
PWR RUN
R UN X3 Inputs (X1 – X4) High-Speed

+
RUN X4
ERR STOP
S TOP C2 6-27 VDC
PORT1 Y1 L 6-240 VAC
Y2 L See Discrete I/O Specifications
LNK/ACT
L
Outputs (Y1 – Y4)
ETHER Y3
NET Y4 L
100MBIT
Transmitter P/S
ACOM
PORT2
+

AD1 I Transmitter 0-20mA

TX2 See Analog I/O Specifications
AD2 I Transmitter 0-20mA
Current
RX2
AD3 I Transmitter 0-20mA
Input (AD1I – AD4I)
RS-232
RS 232
AD4 I Transmitter 0-20mA
RS-485
RS-
-485
485
5 DA+V
PO
ORT3
PORT3
See Analog I/O Specifications
+ DA1 I
+

TX3
TX
X3 _ DA2 I 24VDC Current
RX
X3
RX3 Output (DA1I – DA2I)
LG
G ACOM

NOTE: There are no ZIPLink pre-wired PLC connection cables and modules for the Analog
PLCs (cannot mix discrete I/O and analog I/O signals in a ZIPLink cable).

NOTE: When using Ethernet Analog PLCs, you must use CLICK programming software version
V2.20 or later.

General Specifications
Current Consumption at 24VDC 160mA
Terminal Block Replacement Part No. C0-16TB
Weight 5.3 oz (151g)

www.automationdirect.com CLICK PLCs tCLP-110

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Ethernet Analog PLC

C0-12DRE-1-D (cont’d)
X1 - X4 (High-Speed)
Discrete I/O Specifications - Inputs Equivalent Discrete Input Circuit 3.3 V

Inputs per Module 4 (Source/Sink) Internal Module Circuitry

Operating Voltage Range 24VDC 24 VDC INPUT

Input Voltage Range 21.6–26.4 VDC X1-X4

Optical Isolator
VCC
+
Input Current Typ 6.5 mA @ 24VDC +

Input Impedance 3.9 kq @ 24VDC COM GND

Maximum Input Frequency X1-X4: 100kHz

C1

ON Voltage Level > 19VDC

OFF Voltage Level < 2VDC
Minimum ON Current 4.5 mA C0-12DRE-1-D Temperature Derating Chart
Maximum OFF Current 0.5 mA
4
OFF to ON Response Typ 3µs, Max 5µs Inputs
ON to OFF Response Typ 1µs, Max 3µs 3

Status Indicators

Points
Logic Side (4 points, green LED) 2
Commons 1 (4 points/common)
1

0
0 10 20 30 40 50 55 °C
32 50 68 85 104 122 131 °F
Ambient Air Temperature (°C/°F)

Y1 - Y4
Discrete I/O Specifications - Outputs Equivalent Discrete Output Circuit
Outputs per Module 4 Internal Module Circuitry
Operating Voltage Range 6–27 VDC / 6–240 VAC 6-27 VDC
6-240 VAC 24V
OUTPUT
Output Type Relay, form A (SPST) L
Y1-Y4

AC Frequency 47–63 Hz
Maximum Current 1A/point (resistive)
Minimum Load Current 5mA @ 5VDC COM

C2
Maximum Inrush Current 3A for 10ms
OFF to ON Response < 15ms
ON to OFF Response < 15ms
Status Indicators Logic Side (4 points, red LED)
Commons per Module 1 (4 points/common) C0-12DRE-1-D Temperature Derating Chart

Typical Relay Life (Operations) 4

at Room Temperature 3
Outputs

Voltage & Load Type Load Current: 1A

Points

2
30VDC Resistive 300,000 cycles
30VDC Solenoid 50,000 cycles 1
120VAC Resistive 500,000 cycles
0
120VAC Solenoid 200,000 cycles
0 10 20 30 40 50 55 °C
ON to OFF = 1 cycle 32 50 68 85 104 122 131 °F
Ambient Air Temperature (°C/°F)

www.automationdirect.com CLICK PLCs tCLP-111

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Ethernet Analog PLC

C0-12DRE-1-D (cont’d)

AD1I - AD4I
Analog Specifications - Current Input Analog Current Input Circuit
Inputs per Module 4 (Current)
Input Range 0–20 mA (sink) Internal Module Circuitry
Resolution 12-bit
ADxI
Conversion Time 50ms Current A/D
Input Impedance 125q Transmitter 0V 125Ω
Converter
ACOM
Input Stability ±2 LSB maximum
Full-Scale Calibration Error ±2% maximum +

Offset Calibration Error ±0.1 mA maximum Transmitter

P/S
Accuracy vs. Temperature Error ±100ppm / °C maximum

DA1I - DA2I
Analog Specifications - Current Output Analog Current Output Circuit
Outputs per Module 2 (current) Internal Module Circuitry
Output Range 4–20 mA (source) DA+V
Resolution 12-bit +
– D/A
Conversion Time 1ms
24VDC
Converter
+
Load Impedance 250q Typ (200q to 800q) DAxI
Loop Supply Voltage 24VDC Typ (21.6–26.4)
External +

Full-Scale Calibration Error ±2% maximum Load

ACOM
–

Offset Calibration Error ±25mA maximum

Accuracy vs. Temperature Error ±120ppm / °C maximum
External DC Power Required 21.6–26.4 VDC

www.automationdirect.com CLICK PLCs tCLP-112

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Specifications

General Specifications General Specifications
For All CLICK PLC Analog, analog combo I/O modules only:
32°F to 140°F (0°C to 60°C);
Products Operating Temperature All other modules:
32°F to 131°F (0°C to 55°C),
These general specifications apply to all IEC 60068-2-14 (Test Nb, Thermal Shock)
CLICK PLCs and optional power supply –4°F to 158°F (–20°C to 70°C)
products. Please refer to the appropriate IEC 60068-2-1 (Test Ab, Cold)
Storage Temperature IEC 60068-2-2 (Test Bb, Dry Heat)
I/O temperature derating charts under both
IEC 60068-2-14 (Test Na, Thermal Shock)
the PLC and I/O module specifications to
determine best operating conditions based Ambient Humidity 30% to 95% relative humidity (non–condensing)

on the ambient temperature of your partic- Environmental Air No corrosive gases. Environmental pollution level is 2 (UL840)
MIL STD 810C, Method 514.2, EC60068-2-27, Category [f], Procedure[VIII]
ular application. Vibration JIS C60068-2-27 (Sine wave vibration test)
MIL STD 810C, Method 516.2, IEC60068-2-27,
Shock JIS C60068-2-27, Category [f], Procedure[VIII]
<EN61131-2>
EN61000-4-2 (ESD)
EN61000-4-3 (RFI)
EN61000-4-4 (FTB)
EN61000-4-5 (Surge)
Noise Immunity EN61000-4-6 (Conducted)
EN61000-4-8 (Power frequency magnetic field immunity)

<Local Test>
Impulse noise 1μs, 1000V
RFI: No interference measured at 150 and 450 MHz (5w/15cm)
Emissions EN55011:1998 Class A; EN61000-6-4:2007+A1:2011
UL508, UL61010-2-201 (File No. E157382, E316037); CE (EN61131-2); CUL
Agency Approvals Canadian C22.2
Other RoHS 2011/65/EU Amendment (EU)2015/863

www.automationdirect.com CLICK PLCs tCLP-68

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Specifications

PLC Unit Specifications
Basic, Standard and Analog PLC Unit Specifications
Basic PLC Standard PLC Analog PLC
Stored Program/Cyclic Stored Program/Cyclic Stored Program/Cyclic
Control Method execution method execution method execution method
I/O Numbering System Fixed in Decimal Fixed in Decimal Fixed in Decimal
Ladder Memory (steps) 8000 8000 8000
Total Data Memory (words) 8000 8000 8000
Contact Execution (Boolean) < 0.6 us < 0.6 us < 0.6 us
Typical Scan (1K Boolean) 1-2 ms 1-2 ms 1-2 ms
RLL Ladder Style Programming Yes Yes Yes
Run Time Edits No No No
Scan Variable / fixed Variable / fixed Variable / fixed
CLICK Programming Software Yes Yes Yes
for Windows
Yes (two RS-232 ports and Yes (two RS-232 ports and
Built-in Communication Ports Yes (two RS-232 ports) one RS-485 port) one RS-485 port)
Protocols Protocols: Modbus RTU (master/slave) and ASCII (in/out)
FLASH Memory Standard on PLC Standard on PLC Standard on PLC
Built-in Discrete I/O points 8 inputs, 6 outputs 8 inputs, 6 outputs 4 inputs, 4 outputs
Built-in Analog I/O Channels No No 2 inputs, 2 outputs
Number of Instructions Available 21 21 21
Control Relays 2000 2000 2000
System Control Relays 1000 1000 1000
Timers 500 500 500
Counters 250 250 250
Interrupts Yes (external: 8 / timed: 4) Yes (external: 8 / timed: 4) Yes (external: 4 / timed: 4)
Subroutines Yes Yes Yes
For/Next Loops Yes Yes Yes
Math (Integer and Hex) Yes Yes Yes
Drum Sequencer Instruction Yes Yes Yes
Internal Diagnostics Yes Yes Yes
Password Security Yes Yes Yes
System Error Log Yes Yes Yes
User Error Log No No No
Memory Backup Super Capacitor Super Capacitor + Battery Super Capacitor + Battery
Yes (battery sold separately; Yes (battery sold separately;
Battery Backup No
part # D2-BAT-1) part # D2-BAT-1)
Calendar/Clock No Yes Yes
I/O Terminal Block Replacement AutomationDirect p/n C0-16TB AutomationDirect p/n C0-16TB AutomationDirect p/n C0-16TB
Communication Port & Terminal
Block Replacement N/A AutomationDirect p/n C0-3TB AutomationDirect p/n C0-3TB

24VDC Power Terminal Block AutomationDirect p/n C0-4TB AutomationDirect p/n C0-4TB AutomationDirect p/n C0-4TB
Replacement

www.automationdirect.com CLICK PLCs tCLP-69

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Specifications

PLC Unit Specifications (continued)
Ethernet Basic, Standard and Analog PLC Unit Specifications
Ethernet Basic PLC Ethernet Standard PLC Ethernet Analog PLC
Control Method Stored Program/Cyclic execution method Stored Program/Cyclic execution method Stored Program/Cyclic execution method
I/O Numbering System Fixed in Decimal Fixed in Decimal Fixed in Decimal
Ladder Memory (steps) 8000 8000 8000
Total Data Memory (words) 8000 8000 8000
Contact Execution (Boolean) < 0.2 µs < 0.2 µs < 0.2 µs
Typical Scan (1K Boolean) < 1ms < 1ms < 1ms
RLL Ladder Style Programming Yes Yes Yes
Run Time Edits Yes Yes Yes
Scan Variable / fixed Variable / fixed Variable / fixed
CLICK Programming Software for Yes Yes Yes
Windows
Yes (one Ethernet port and Yes (one Ethernet port, one RS-232 port and one Yes (one Ethernet port, one RS-232 port and one
Built-in Communication Ports one RS-232 port) RS-485 port) RS-485 port)
Protocols Modbus RTU (master/slave) and ASCII (in/out), Modbus TCP (client/server), EtherNet/IP Implicit and Explicit (adapter server)
FLASH Memory Standard on PLC Standard on PLC Standard on PLC
Built-in Discrete I/O points 8 inputs, 6 outputs 8 inputs, 6 outputs 4 inputs, 4 outputs
Built-in Analog I/O Channels No No 2 or 4 inputs; 2 outputs
Number of High-Speed Input Points 4 8 4
Number of High-Speed Counters 4 6 4
PID Control Loops 8 8 8
Number of Instructions Available 21 21 21
Control Relays 2000 2000 2000
System Control Relays 1000 1000 1000
Timers 500 500 500
Counters 250 250 250
Interrupts Yes (external: 8 / timed: 4) Yes (external: 8 / timed: 4) Yes (external: 4 / timed: 4)
Subroutines Yes Yes Yes
For/Next Loops Yes Yes Yes
Math (Integer and Hex) Yes Yes Yes
Drum Sequencer Instruction Yes Yes Yes
Internal Diagnostics Yes Yes Yes
Password Security Yes Yes Yes
System Error Log Yes Yes Yes
User Error Log No No No
Memory Backup Super Capacitor + Battery Super Capacitor + Battery Super Capacitor + Battery
Battery Backup Yes (battery part # D2-BAT-1) Yes (battery part # D2-BAT-1) Yes (battery part # D2-BAT-1)
Calendar/Clock Yes Yes Yes
I/O Terminal Block Replacement AutomationDirect p/n C0-16TB AutomationDirect p/n C0-16TB AutomationDirect p/n C0-16TB
Communication Port & Terminal
Block Replacement N/A AutomationDirect p/n C0-3TB AutomationDirect p/n C0-3TB

24VDC Power Terminal Block AutomationDirect p/n C0-4TB AutomationDirect p/n C0-4TB AutomationDirect p/n C0-4TB
Replacement

www.automationdirect.com CLICK PLCs tCLP-70

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK Specifications
CLICK PLC Hardware/Software Compatibility
CLICK PLCs require a minimum software version of v2.50 for the PID function. The table
below shows the most recent software and hardware versions required for the High-Speed
input operation capability to be accessible.

CLICK PLC Features Software Compatibility

Minimum CLICK Software Version
High-Speed
CPU Type Part Number Hardware EtherNet/IP PID DHCP
Inputs
C0-00DD1-D
C0-00DD2-D
Basic v1.00 N/A N/A N/A N/A
C0-00DR-D
C0-00AR-D
C0-01DD1-D
C0-01DD2-D
Standard v1.20 N/A N/A N/A N/A
C0-01DR-D
C0-01AR-D
C0-02DD1-D (before SN 171208001) v1.12
C0-02DD1-D (after SN 171208001) v2.10
C0-02DD2-D (before SN 174018001) v1.12
Analog N/A N/A N/A N/A
C0-02DD2-D (after SN 174018001) v2.10
C0-02DR-D (before SN 173158001) v1.12
C0-02DR-D (after SN 173158001) v2.10
Ethernet CPUs Ethernet CPUs require v2.40 for EtherNet/IP communications
C0-10DD1E-D
C0-10DD2E-D v2.30
Ethernet Basic v2.00 v2.40 v2.50 v3.00
C0-10DRE-D
C0-10ARE-D N/A
C0-11DD1E-D
C0-11DD2E-D v2.30
Ethernet Standard v2.00 v2.40 v2.50 v3.00
C0-11DRE-D
C0-11ARE-D N/A
C0-12DD1E-D
C0-12DD2E-D v2.30
C0-12DRE-D
C0-12ARE-D N/A
C0-12DD1E-1-D
C0-12DD2E-1-D v2.30
Ethernet Analog v2.20 v2.40 v2.50 v3.00
C0-12DRE-1-D
C0-12ARE-1-D N/A
C0-12DD1E-2-D
C0-12DD2E-2-D v2.30
C0-12DRE-2-D
C0-12ARE-2-D N/A
C0-08NE3
v1.20
C0-16NE3
C0-04AD-1
C0-04AD-2
C0-04DA-1
C0-04DA-2
C0-4AD2DA-1
I/O Modules N/A N/A N/A N/A
C0-4AD2DA-2 v1.40
C0-04RTD
C0-04THM
C0-08CDR
C0-16CDD1
C0-16CDD2
Other modules v1.00

www.automationdirect.com CLICK PLCs tCLP-71

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Family Overview

What you’ll need
Of course, what you’ll need for your system 1. Select your CLICK or CLICK PLUS PLC unit.
depends on your particular application, but
this overview shows you what you’ll need for
a simple system.

C2-14D1

2. If using a CLICK PLUS PLC, select an

IN 24V
C1
1
2

6.5mA
3

Option Slot Module if desired. 4

C2
5
6
7
8

OUT 5-27V
C3
1
2
3

0.1A
4
C4
5
6
+V

3. If you need additional I/O, select from 24

different types of Stackable I/O modules.

4. Select a 24VDC power supply.

or

5. Download the FREE CLICK

programming software.
support.automationdirect.com/
products/clickplcs.html

6. Download the FREE CLICK mobile app.

The CLICK mobile app is available for iOS and Android.
It can connect to your C2-02CPU or C2-03CPU over
Bluetooth to provision the PLC onto a Wi-Fi network.
(PLC requires an external antenna)

www.automationdirect.com CLICK PLCs tCLP-10

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Family Overview

What you’ll need (continued)

Select your PC-to-PLC programming cable.

7. If your PC has a USB port, use cable EA-MG-PGM-CBL to connect to the PLC port. If your PC has a 9-pin serial
communications port, use programming cable D2-DSCBL. If your PC has an Ethernet port, use C5E-STPYL-C3 (cross-
over) or C5E-STPYL-S3 (straight through) Ethernet cable. If your PC is on a network with a wireless access point, you
can connect using one of our Wi-Fi anteannas.

D2-DSCBL
USB-CBL-AMICB6 C5E-STPYL-C3 (crossover)
C5E-STPYL-S3 (straight through)

(PC requires RS-232 port

For Ethernet PLC Unit
to use this cable)

USB A to USB micro B or

Programming Cable Assembly
(CLICK PLUS Only) SE-ANT250 or
Wi-Fi/Bluetooth Dome Antenna
(C2-02CPU & C2-03CPU only)
EA-MG-PGM-CBL

Connects to PC USB Port

or
SE-ANT210
Wi-Fi/Bluetooth Whip Antenna
(C2-02CPU & C2-03CPU only)
(nonmetal enclosure only)

8. Select tools, wire, and provide power.

Screwdriver Wire Strippers Hookup Wire

TW-SD-MSL-2 DN-WS

www.automationdirect.com CLICK PLCs tCLP-11

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Power Supplies
Power Supplies CLICK 24VDC Power Supply Ratings
The CLICK PLC family offers two 24VDC power Part Number Output Current Price
supplies. They are identical except for the output C0-00AC 0.5 A $31.00
current. C0-01AC 1.3 A $42.50

It is not mandatory to use one of these CLICK C0-00AC Power Supply Input Specifications
power supplies for the CLICK/CLICK PLUS PLC C0-00AC
Part Number C0-00AC C0-01AC
system. You can use any other 24VDC power supply
that Automationdirect.com offers, including the Input Voltage Range 85–264 VAC

PSP24-DC12-1 12 to 24 VDC converter shown below. Input Frequency 47–63 Hz

0.3 A @ 100VAC, 0.9 A @ 100VAC,
Input Current (typical) 0.2 A @ 200VAC 0.6 A @ 200VAC
C0-00AC Power Supply
Inrush Current 30A
Limited auxiliary AC power supply allows you to Efficiency 80% typical
power the 24VDC CLICK C0 and C2 series PLCs with
100–240 VAC supply power. The 0.5 A DC power C0-00AC Power Supply Output Specifications
supply is capable of controlling the PLC plus a limited Part Number C0-00AC C0-01AC
configuration based on the power budget of each Output Voltage Range 23–25 VDC
I/O module. The C0-00AC is a low-cost solution for
Output Current 0.5 A 1.3 A
applications requiring only minimal I/O and power
Ripple 200mV p-p max (0–55°C)
consumption. This power supply will not support a
fully-populated CLICK PLC system with all possible I/O Ripple Noise 300mV p-p max (0–55°C)
@ 0.65 A @ 1.6 A
module combinations. C0-01AC Over Current Protection (automatic recovery) (automatic recovery)

C0-01AC Power Supply Over Voltage Protection @ 27.6 V (clamped by Zener diode)
Start-up Time 1000ms max at rated input and load
Expanded auxiliary AC power supply allows you to Hold-up Time 10ms minimum at 85VAC, I=max
power the 24VDC CLICK C0 and C2 series PLCs with
100–240 VAC supply power. The 1.3 A DC power C0-00AC Power Supply General Specifications
supply is capable of supporting a fully-populated Part Number C0-00AC C0-01AC
CLICK PLC system with all possible I/O module
Ambient Operating 32–131°F [0–55°C]
combinations, with no concerns for exceeding the Temperature
power budget. Storage Temperature -4–158°F [-20–70°C]

PSP24-DC12-1 DC-DC Converter Humidity 30–95%, non-condensing

Vibration Resistance JIS C60068-2-6, sine wave vibration
With this DC-DC converter you can operate the Shock Resistance JIS C60068-2-27
CLICK/CLICK PLUS PLC with 12VDC input power. Voltage Withstand
Input-Output 1500VAC, 5mA cutoff current
Input-Ground 1500VAC, 5mA cutoff current
CLICK Power Supply CLICK PLC
Output-Ground 500VAC, 5mA cutoff current
Insulation Resistance
Input-Output 10MΩ minimum, 500VDC
Input-Ground 10MΩ minimum, 500VDC
Output-Ground 5MΩ minimum, 500VDC
Noise Immunity FCC Class A, EN55022:1998 Class A
5P terminal block, Fujicon UF2362AX series
Input/Output Interface or equivalent
UL508, UL1604, EN61010-1 (IEC 1010-1),
Agency Approvals CAN/CSA E60079-15:02, JIS C0025
Weight 5.3 oz [150g] 6.0 oz [170g]

24V PSP24-DC12-1 DC-DC Converter Specifications

0V Input Voltage Range 9.5–18 VDC
Input Power (no load) 1.0 W max.
G Startup Voltage 8.4 VDC
Undervoltage Shutdown 7.6 VDC
Output Voltage Range 24–28 VDC (adjustable)

24VDC power is supplied to the PLC unit through wiring Output Current 1.0 A
connected from the power supply output to the 4-pin 24VDC Short Circuit Protection Current limited at 110% typical
input connector located on the bottom of the PLC unit. Weight 7.5 oz (213g)
PSP24-DC12-1

www.automationdirect.com CLICK PLCs tCLP-16

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Accessories
C2-USER-M $0.00 EA-MG-PGM-CBL $46.50 C0-3TB $7.75
CLICK PLUS PLC Hardware User PC to Panel Programming Cable Spare 3-Pole Terminal Block
Manual Assembly for C-more Micro-Graphic Replacement 3-pole terminal block for the 3-wire
Manual covers all CLICK PLUS PLC and I/O Panels and CLICK/CLICK PLUS PLCs RS-485 Port 3 on CLICK Standard and Analog
module installation and wiring, specifications, PLCs as well as the CLICK PLUS C2-03CPU.
The 6ft cable assembly connects a personal
error codes and troubleshooting guide. The Sold in packs of 2.
computer to any C-more Micro-Graphic panel,
CLICK PLUS PLC Hardware User Manual can be CLICK PLC, or select CLICK PLUS PLC for setup
downloaded free at the AutomationDirect Web and programming.
site; www.automationdirect.com Note: This cable assembly uses the PC’s USB port and converts
the signals to serial transmissions. The USB port supplies
5VDC to the Micro-Graphic panel for configuration operations.

Assembly includes standard USB A-type connector

C0-4TB $7.75
to B-type connector cable, custom converter, and Spare 24VDC Power Terminal Block
a RS232C cable with RJ12 modular connector
on each end. Replacement terminal block for the 24VDC
supply power to the PLC. Sold in packs of 2.

C0-USER-M $0.00
CLICK PLC Hardware User Manual
Manual covers all CLICK PLC and I/O module
installation and wiring, specifications, error codes C0-8TB $13.50
and troubleshooting guide. The CLICK PLC
Hardware User Manual can be downloaded free Spare 8-Point I/O
at the AutomationDirect Web site; www.automa- Terminal Block
tiondirect.com
USB-CBL-AMICB6 $3.75 Replacement terminal
block for the 8-point I/O
USB A to USB micro B Programming Cable
modules. Sold in packs
Assembly (CLICK PLUS Only)
of 2.
Programming Cable, USB A to USB micro B, 6ft.
(1.83 m) length. For use with CLICK PLUS PLCs
and most USB devices. The USB port supplies
5VDC to the CLICK PLUS CPU for programming. C0-8TB-1 $15.00
Spare 13-Point I/O Terminal
Block
C0-PGMSW $11.00 Replacement terminal block for the
8-point I/O relay modules. Sold in packs of 2.
Programming Software CD-ROM
The programming software can be downloaded
free at the AutomationDirect Web site, or the CD
can be purchased from the AutomationDirect D2-DSCBL $24.00
online Web store. www.automationdirect.com
Programming Cable for CLICK/CLICK PLUS
and DirectLOGIC PLCs 12ft. (3.66 m) RS232
shielded PC programming cable for CLICK, select
CLICK PLUS PLCs, DL05, DL06, DL105, DL205,
D3-350, D4-450, D4-454, and Do-more H2
and T1H series CPUs. 9-pin D-shell female C0-16TB $18.50
connector to an RJ12 6P6C connector.
Spare 16-Point I/O Terminal Block
Replacement terminal block
for the 16-point I/O modules
and PLC built-in I/O. Sold in
packs of 2.
Note: If your PC has a USB port but does not
have a serial port, you must use programming
cable EA-MG-PGM-CBL to connect to CLICK
PLCs. For CLICK PLUS PLCs, you may also use
USB-CBL-AMICB6

Book 1 (14.2)
www.automationdirect.com CLICK PLCs tCLP-157
 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Accessories
SE-ANT250 $42.50 C2-FILL $8.00
Wi-Fi/Bluetooth Dome Antenna CPU Option Slot Cover
2.4 GHz antenna, IP67, panel mount,
Snap-on cover for
9.8ft (3m) cable length, for external mounting
CLICK PLUS CPU
when CLICK PLUS PLC is installed in a metallic
Option Slot in
enclosure.
applications without
an Option Slot
module present.

D2-BAT-1 $5.75
SE-ANT210 $9.00 Replacement battery for Standard, Analog,
Wi-Fi/Bluetooth Whip Antenna Ethernet Standard and Ethernet Analog PLC
Whip/straight 2.4 GHz antenna, units.
IP65, connector mount. Not recommended for
installation in a metallic enclosure.

D0-MC-BAT $3.00
Replacement battery for CLICK PLUS PLC units.

DN-EB35MN $21.50
DINnectors End Bracket

DN-WS $57.00
Wire Stripper
C-more and C-more Micro
Graphic Operator Interfaces

TW-SD-MSL-2 $3.00
ZIPLink Wiring Systems Insulated Slotted Screwdriver
0.4 x 2.5 x 80 mm slotted screwdriver for
terminal blocks.

www.automationdirect.com CLICK PLCs tCLP-158