SIP5 Hardware V08.40 Manual C002-K en

Preface
Open Source Software
Table of Contents
SIPROTEC 5 Introduction 1
Hardware Description Forms of Devices and On-Site Operation
Panels 2
V8.40 and higher
Electronic Modules 3
Plug-In Modules 4
Manual Working on the Device 5
Technical Data 6
Ordering Information 7
Appendix A
Literature
Glossary
Index
C53000-G5040-C002-K
NOTE
i For your own safety, observe the warnings and safety instructions contained in this document, if available.
Disclaimer of Liability Copyright

Subject to changes and errors. The information given in Copyright © Siemens 2020. All rights reserved.
this document only contains general descriptions and/or The disclosure, duplication, distribution and editing of this
performance features which may not always specifically document, or utilization and communication of the content
reflect those described, or which may undergo modifica- are not permitted, unless authorized in writing. All rights,
tion in the course of further development of the products. including rights created by patent grant or registration of a
The requested performance features are binding only when utility model or a design, are reserved.
they are expressly agreed upon in the concluded contract.
Document version: C53000-G5040-C002-K.04 Trademarks
Edition: 11.2020
SIPROTEC, DIGSI, SIGRA, SIGUARD, SIMEAS SAFIR, SICAM,
Version of the product described: V8.40 and higher and MindSphere are trademarks of Siemens. Any unauthor-
ized use is prohibited.
Preface
Purpose of the Manual

This manual describes the hardware of the SIPROTEC 5 device family and provides general information on the
product structure, the modules and technical data.
Target Audience
Protection system engineers, commissioning engineers, persons entrusted with the setting, testing and main-
tenance of automation, selective protection and control equipment, and operational crew in electrical installa-
tions and power plants.
Scope
This manual applies to the SIPROTEC 5 device family.
Further Documentation
[dw_Product-overview_SIP5_Hardware-manual, 4, en_US]
• Device manuals
Each Device manual describes the functions and applications of a specific SIPROTEC 5 device. The printed
manual and the online help for the device have the same informational structure.
SIPROTEC 5, Hardware Description, Manual 3

C53000-G5040-C002-K, Edition 11.2020
Preface
• Hardware manual
The Hardware manual describes the hardware building blocks and device combinations of the SIPROTEC 5
device family.
• Operating manual
The Operating manual describes the basic principles and procedures for operating and assembling the
devices of the SIPROTEC 5 range.
• Communication protocol manual

The Communication protocol manual contains a description of the protocols for communication within
the SIPROTEC 5 device family and to higher-level network control centers.
• Security manual
The Security manual describes the security features of the SIPROTEC 5 devices and DIGSI 5.
• Process bus manual

The process bus manual describes the functions and applications specific for process bus in SIPROTEC 5.
• Product information
The Product information includes general information about device installation, technical data, limiting
values for input and output modules, and conditions when preparing for operation. This document is
provided with each SIPROTEC 5 device.
• Engineering Guide
The Engineering Guide describes the essential steps when engineering with DIGSI 5. In addition, the Engi-
neering Guide shows you how to load a planned configuration to a SIPROTEC 5 device and update the
functionality of the SIPROTEC 5 device.
• DIGSI 5 online help

The DIGSI 5 online help contains a help package for DIGSI 5 and CFC.
The help package for DIGSI 5 includes a description of the basic operation of software, the DIGSI princi-
ples and editors. The help package for CFC includes an introduction to CFC programming, basic examples
of working with CFC, and a reference chapter with all the CFC blocks available for the SIPROTEC 5 range.
• SIPROTEC 5/DIGSI 5 Tutorial

The tutorial on the DVD contains brief information about important product features, more detailed infor-
mation about the individual technical areas, as well as operating sequences with tasks based on practical
operation and a brief explanation.
• SIPROTEC 5 catalog
The SIPROTEC 5 catalog describes the system features and the devices of SIPROTEC 5.
• Selection guide for SIPROTEC and Reyrolle

The selection guide offers an overview of the device series of the Siemens protection devices, and a
device selection table.
Indication of Conformity
This product complies with the directive of the Council of the European Communities
on harmonization of the laws of the Member States concerning electromagnetic
compatibility (EMC Directive 2014/30/EU), restriction on usage of hazardous
substances in electrical and electronic equipment (RoHS Directive 2011/65/EU), and
electrical equipment for use within specified voltage limits (Low Voltage Directive
2014/35/EU).
This conformity has been proved by tests performed according to the Council Directive
in accordance with the product standard EN 60255-26 (for EMC directive), the standard
EN 50581 (for RoHS directive), and with the product standard EN 60255-27 (for Low
Voltage Directive) by Siemens.
The device is designed and manufactured for application in an industrial environment.
The product conforms with the international standards of IEC 60255 and the German
standard VDE 0435.
4 SIPROTEC 5, Hardware Description, Manual

C53000-G5040-C002-K, Edition 11.2020
Preface
Standards
IEEE Std C 37.90
The technical data of the product is approved in accordance with UL.
For more information about the UL database, see ul.com
You can find the product with the UL File Number E194016.
IND. CONT. EQ.

69CA
Additional Support
For questions about the system, contact your Siemens sales partner.
Customer Support Center

Our Customer Support Center provides a 24-hour service.
Siemens AG
Smart Infrastructure – Digital Grid
Customer Support Center
Tel.: +49 911 2155 4466
E-Mail: [email protected]
Training Courses
Inquiries regarding individual training courses should be addressed to our Training Center:
Siemens AG Phone: +49 (911) 433-7415
Siemens Power Academy TD Fax: +49 (911) 433-7929
Humboldtstrasse 59 E-mail: [email protected]
90459 Nuremberg Internet: www.siemens.com/poweracademy
Germany
Notes on Safety
This document is not a complete index of all safety measures required for operation of the equipment (module
or device). However, it comprises important information that must be followed for personal safety, as well as
to avoid material damage. Information is highlighted and illustrated as follows according to the degree of
danger:
! DANGER
DANGER means that death or severe injury will result if the measures specified are not taken.
² Comply with all instructions, in order to avoid death or severe injuries.
! WARNING
WARNING means that death or severe injury may result if the measures specified are not taken.
² Comply with all instructions, in order to avoid death or severe injuries.

C53000-G5040-C002-K, Edition 11.2020
Preface
! CAUTION
CAUTION means that medium-severe or slight injuries can occur if the specified measures are not taken.
² Comply with all instructions, in order to avoid moderate or minor injuries.
NOTICE
NOTICE means that property damage can result if the measures specified are not taken.
² Comply with all instructions, in order to avoid property damage.
NOTE
i Important information about the product, product handling or a certain section of the documentation
which must be given attention.
Qualified Electrical Engineering Personnel

Only qualified electrical engineering personnel may commission and operate the equipment (module, device)
described in this document. Qualified electrical engineering personnel in the sense of this document are
people who can demonstrate technical qualifications as electrical technicians. These persons may commission,
isolate, ground and label devices, systems and circuits according to the standards of safety engineering.
Proper Use
The equipment (device, module) may be used only for such applications as set out in the catalogs and the
technical description, and only in combination with third-party equipment recommended and approved by
Siemens.
Problem-free and safe operation of the product depends on the following:
• Proper transport
• Proper storage, setup and installation
• Proper operation and maintenance

When electrical equipment is operated, hazardous voltages are inevitably present in certain parts. If proper
action is not taken, death, severe injury or property damage can result:
• The equipment must be grounded at the grounding terminal before any connections are made.
• All circuit components connected to the power supply may be subject to dangerous voltage.
• Hazardous voltages may be present in equipment even after the supply voltage has been disconnected
(capacitors can still be charged).
• Operation of equipment with exposed current-transformer circuits is prohibited. Before disconnecting the
equipment, ensure that the current-transformer circuits are short-circuited.
• The limiting values stated in the document must not be exceeded. This must also be considered during
testing and commissioning.
Selection of Used Symbols on the Device
Nr. Symbol Description
1 Direct current, IEC 60417, 5031
2 Alternating current, IEC 60417, 5032

C53000-G5040-C002-K, Edition 11.2020
Preface
Nr. Symbol Description
3 Direct and alternating current, IEC 60417, 5033
4 Earth (ground) terminal, IEC 60417, 5017
5 Protective conductor terminal, IEC 60417, 5019
6 Caution, risk of electric shock
7 Caution, risk of danger, ISO 7000, 0434
8 Protective Insulation, IEC 60417, 5172, Safety Class II devices
9 Guideline 2002/96/EC for electrical and electronic devices
10 Guideline for the Eurasian Market

C53000-G5040-C002-K, Edition 11.2020
C53000-G5040-C002-K, Edition 11.2020
Open Source Software
The product contains, among other things, Open Source Software developed by third parties. The Open
Source Software used in the product and the license agreements concerning this software can be found in the
Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those
license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the
event of conflicts between Siemens license conditions and the Open Source Software license conditions, the
Open Source Software conditions shall prevail with respect to the Open Source Software portions of the soft-
ware. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software
License Conditions provide for it you can order the source code of the Open Source Software from your
Siemens sales contact – against payment of the shipping and handling charges – for a period of at least
3 years after purchase of the product. We are liable for the product including the Open Source Software
contained in it pursuant to the license conditions applicable to the product. Any liability for the Open Source
Software beyond the program flow intended for the product is explicitly excluded. Furthermore, any liability
for defects resulting from modifications to the Open Source Software by you or third parties is excluded. We
do not provide any technical support for the product if it has been modified.
When using DIGSI 5 in online mode, you are provided with the option to go to the main menu Show open
source software information and read and display the Readme_OSS file containing the original license text
and copyright information.
To do this, the following steps are necessary:
• Switch to online mode.
• Select the device.
• Select Online in the menu bar.
• Click Show open source software information.
NOTE
i To read the Readme_OSS file, a PDF viewer must be installed on the computer.
In order to operate SIPROTEC 5 devices, a valid DIGSI 5 license is required.

C53000-G5040-C002-K, Edition 11.2020
C53000-G5040-C002-K, Edition 11.2020
Table of Contents
Preface.......................................................................................................................................................... 3
Open Source Software..................................................................................................................................9
1 Introduction................................................................................................................................................17
1.1 Advantages of SIPROTEC 5 ................................................................................................18
1.2 Modular Systems and Hardware Characteristics................................................................. 19
2 Forms of Devices and On-Site Operation Panels........................................................................................ 21

2.1 Flush-Mounting Devices.................................................................................................... 22
2.1.1 Description ................................................................................................................. 22
2.2 Surface-Mounted Devices with Integrated On-Site Operation Panel.................................... 31
2.2.1 Description of the Modular Device............................................................................... 31
2.2.2 Description of the Non-Modular Surface-Mounted Device.............................................33
2.3 Surface-Mounted Devices with Detached On-Site Operation Panel..................................... 37
2.3.1 Description.................................................................................................................. 37
2.4 On-Site Operation Panels.................................................................................................. 41
2.4.1 Description.................................................................................................................. 41
2.4.2 Overview of Operating Elements and Display Elements................................................ 43
3 Electronic Modules..................................................................................................................................... 49
3.1 Power-Supply Modules of the Modular Devices.................................................................. 50
3.1.1 Function Description of the Power-Supply Modules of the Modular Devices.................. 50
3.1.2 Power-Supply Module PS201....................................................................................... 50
3.1.2.1 Description............................................................................................................ 50
3.1.2.2 Terminals...............................................................................................................51
3.1.3 Power-Supply Module PS203 for the 2nd Device Row................................................... 54
3.1.3.1 Description............................................................................................................ 54
3.1.3.2 Terminals...............................................................................................................55
3.1.4 Power-Supply Module PS204 for Redundant Power Supply........................................... 57
3.1.4.1 Description............................................................................................................ 57
3.1.4.2 Positioning Specifications....................................................................................... 57
3.1.4.3 Terminals...............................................................................................................60
3.1.5 Plug-In Module Assembly with Integrated Power Supply CB202.................................... 61
3.1.5.1 Description............................................................................................................ 61
3.1.5.2 Terminals...............................................................................................................62
3.2 Input and Output Modules of the Modular Devices............................................................ 64
3.2.1 Function Description of the Input and Output Modules of the Modular Devices.............64
3.2.2 Input and Output Module IO201.................................................................................. 65
3.2.2.1 Description ........................................................................................................... 65
3.2.2.2 Terminals...............................................................................................................66
3.2.3.1 Description............................................................................................................ 68

C53000-G5040-C002-K, Edition 11.2020
Table of Contents
3.2.3.2 Terminals...............................................................................................................69
3.2.4.1 Description ........................................................................................................... 71
3.2.4.2 Terminals...............................................................................................................72
3.2.5.1 Description............................................................................................................ 74
3.2.5.2 Terminals...............................................................................................................75
3.2.6.1 Description ........................................................................................................... 77
3.2.6.2 Terminals...............................................................................................................78
3.2.7.1 Description ........................................................................................................... 80
3.2.7.2 Terminals...............................................................................................................81
3.2.8.1 Description ........................................................................................................... 83
3.2.8.2 Terminals...............................................................................................................83
3.2.9.1 Description............................................................................................................ 85
3.2.9.2 Terminals...............................................................................................................86
3.2.10.1 Description............................................................................................................ 88
3.2.10.2 Terminals...............................................................................................................89
3.2.11.1 Description............................................................................................................ 91
3.2.11.2 Terminals...............................................................................................................92
3.2.12.1 Description............................................................................................................ 94
3.2.12.2 Terminals...............................................................................................................95
3.2.13.1 Description............................................................................................................ 97
3.2.13.2 Terminals...............................................................................................................98
3.2.14 Input and Output Module IO214................................................................................ 100
3.2.14.1 Description.......................................................................................................... 100
3.2.14.2 Terminals.............................................................................................................101
3.2.15.1 Description.......................................................................................................... 103
3.2.15.2 Terminals ............................................................................................................ 103
3.2.16 Input Module IO216.................................................................................................. 104
3.2.16.1 Description.......................................................................................................... 104
3.2.16.2 Terminals.............................................................................................................104
3.2.17 Input Module IO230.................................................................................................. 106
3.2.17.1 Description.......................................................................................................... 106
3.2.17.2 Terminals.............................................................................................................107
3.2.18.1 Description.......................................................................................................... 110
3.2.18.2 Terminals.............................................................................................................110
3.2.19 Input Module IO233.................................................................................................. 112
3.2.19.1 Description.......................................................................................................... 112
3.2.19.2 Terminals.............................................................................................................113
3.2.20.1 Description.......................................................................................................... 116
3.2.20.2 Terminals.............................................................................................................116
3.2.20.3 Connections of GIS-LPIT Sensors........................................................................... 118

C53000-G5040-C002-K, Edition 11.2020
Table of Contents
3.3 Power-Supply Module of Non-Modular Devices (7xx81, 7xx82)........................................124

3.3.1 Power-Supply Module PS101..................................................................................... 124
3.3.1.1 Description.......................................................................................................... 124
3.3.1.2 Terminals.............................................................................................................125
3.4 Input and Output Modules of Non-Modular Devices (7xx81, 7xx82).................................128
3.4.1 Function Description of the Input and Output Modules of the Non-Modular Devices... 128
3.4.2.1 Description.......................................................................................................... 128
3.4.2.2 Terminals.............................................................................................................129
3.4.3.1 Description.......................................................................................................... 131
3.4.3.2 Terminals.............................................................................................................132
3.4.4.1 Description.......................................................................................................... 134
3.4.4.2 Terminals.............................................................................................................135
3.4.5.1 Description.......................................................................................................... 137
3.4.5.2 Terminals.............................................................................................................138
3.4.6.1 Description.......................................................................................................... 140
3.4.6.2 Terminals.............................................................................................................141
3.4.6.3 Connections of Temperature Sensors and Cables.................................................. 143
3.4.7.1 Description.......................................................................................................... 145
3.4.7.2 Terminals.............................................................................................................146
3.4.8.1 Description.......................................................................................................... 148
3.4.8.2 Terminals.............................................................................................................148
4 Plug-In Modules........................................................................................................................................151
4.1 Function Description of Plug-In Modules of Modular and Non-Modular Devices................ 152
4.2 Communication Modules................................................................................................ 153
4.2.1 Overview...................................................................................................................153
4.2.2 Communication Applications of the Plug-In Modules ................................................. 156
4.2.3 Serial Modules for Short Distances............................................................................. 159
4.2.3.1 Special Features of Serial Electrical Modules ........................................................ 159
4.2.3.2 USART-AB-1EL...................................................................................................... 161
4.2.3.3 USART-AC-2EL...................................................................................................... 162
4.2.3.4 USART-AD-1FO.....................................................................................................162
4.2.3.5 USART-AE-2FO..................................................................................................... 163
4.2.4 Serial Modules for Long Distances..............................................................................163
4.2.4.1 Application ..........................................................................................................163
4.2.4.2 USART-AF-1LDFO................................................................................................. 164
4.2.4.3 USART-AG-1LDFO.................................................................................................165
4.2.4.4 USART-AH-1LDFO.................................................................................................165
4.2.4.5 USART-AJ-1LDFO.................................................................................................. 166
4.2.4.6 USART-AK-1LDFO................................................................................................. 167
4.2.4.7 USART-AW-2LDFO................................................................................................ 168
4.2.4.8 USART-AU-2LDFO................................................................................................. 168
4.2.4.9 USART-AX-2LDFO................................................................................................. 169
4.2.4.10 USART-AY-2LDFO................................................................................................. 170
4.2.4.11 USART-AV-2LDFO................................................................................................. 170
4.2.5 Ethernet Modules...................................................................................................... 171
4.2.5.1 Operation of Ethernet Modules............................................................................ 171

C53000-G5040-C002-K, Edition 11.2020
Table of Contents
4.2.5.2 ETH-BA-2EL.......................................................................................................... 173

4.2.5.3 ETH-BB-2FO......................................................................................................... 174
4.2.5.4 ETH-BD-2FO......................................................................................................... 174
4.3 Measuring-Transducer Modules.......................................................................................177
4.3.1 Overview...................................................................................................................177
4.3.2 ANAI-CA-4EL..............................................................................................................177
4.3.3 ARC-CD-3FO ............................................................................................................. 178
5 Working on the Device............................................................................................................................. 179

5.1 First Steps....................................................................................................................... 180
5.1.1 Electrical Inspection...................................................................................................180
5.2 Expanding Modular Devices............................................................................................ 182
5.2.1 Flush-Mounting Devices............................................................................................ 182
5.2.1.1 Basic Rules for Expansion..................................................................................... 182
5.2.1.2 Expanding 1st Device Row....................................................................................183
5.2.1.3 Expanding Devices with 2nd Device Row.............................................................. 184
5.2.2 Surface-Mounted Devices with Integrated On-Site Operation Panel............................ 186
5.2.2.3 Expanding Devices with 2nd Device Row.............................................................. 189
5.2.3 Surface-Mounted Devices with Detached On-Site Operation Panel..............................192
5.3 Plug-In Modules.............................................................................................................. 195
5.3.1 Fasteners...................................................................................................................195
5.3.2 Installation................................................................................................................ 195
5.3.3 Removing ................................................................................................................. 196
5.3.4 Replacement............................................................................................................. 198
5.4 Arc Sensors for Module: ARC-CD-3FO...............................................................................200
5.4.1 Point Sensor.............................................................................................................. 200
5.4.1.1 Description ......................................................................................................... 200
5.4.1.2 Installation .......................................................................................................... 201
5.4.2 Line Sensor................................................................................................................203
5.4.2.1 Description ......................................................................................................... 203
5.4.2.2 Installation .......................................................................................................... 203
5.5 Battery............................................................................................................................206
5.5.1 Description................................................................................................................ 206
5.5.2 Replacing the Battery.................................................................................................207
5.5.3 Environmental Protection Hints..................................................................................207
5.6 SDHC Memory Card ........................................................................................................209
5.7 Installing Current and Voltage Terminals......................................................................... 211
5.7.1 Description ............................................................................................................... 211
5.7.2 Connections of Current Terminals ............................................................................. 214
5.7.3 Connections of Voltage Terminals.............................................................................. 215
5.7.3.1 Connections of Voltage Terminals with Spring Clips ............................................. 215
5.7.3.2 Connections of Voltage Terminals with Screw Connection.................................... 216
5.7.3.3 Connections of Voltage Terminal with Screw Connection for IO111...................... 217
5.7.4 Installation and Removal............................................................................................217
6 Technical Data.......................................................................................................................................... 219

6.1 Analog Inputs................................................................................................................. 220

C53000-G5040-C002-K, Edition 11.2020
Table of Contents
6.2 Supply Voltage................................................................................................................224

6.3 Binary Inputs...................................................................................................................226
6.4 Relay Outputs................................................................................................................. 228
6.5 Light-Emitting Diodes in the On-Site Operation Panel.......................................................231
6.6 Communication Interfaces.............................................................................................. 232
6.7 Electrical Tests................................................................................................................ 235
6.8 Mechanical Tests.............................................................................................................238
6.9 Environmental Conditions............................................................................................... 239
6.10 Operating Conditions...................................................................................................... 241
6.11 Reference Conditions and Influencing Variables...............................................................242
6.12 Approvals....................................................................................................................... 243
6.13 Design Data.................................................................................................................... 244
6.14 Assembly Dimensions..................................................................................................... 247
6.15 Modular Device Name Plate.............................................................................................268
6.16 Name Plate of Non-Modular Devices (7xx81, 7xx82)........................................................270
6.17 Name Plate, UL Approval, Base Module and 1/3 Base Module........................................... 271
6.18 Name Plate, UL Approval, Expansion Module................................................................... 272
6.19 Battery............................................................................................................................273
6.20 SDHC Memory Card ........................................................................................................274
6.21 Display Resolution...........................................................................................................275
7 Ordering Information............................................................................................................................... 277

7.1 Ordering Spare Parts and Accessories.............................................................................. 278
7.1.1 Order Configurator and Order Options....................................................................... 278
7.1.2 Ordering Accessories................................................................................................. 278
A Appendix.................................................................................................................................................. 281
A.1 Hardware/Firmware Compatibility List............................................................................. 282
Literature.................................................................................................................................................. 287
Glossary.................................................................................................................................................... 289
Index.........................................................................................................................................................291

C53000-G5040-C002-K, Edition 11.2020
C53000-G5040-C002-K, Edition 11.2020
1 Introduction
1.1 Advantages of SIPROTEC 5 18

1.2 Modular Systems and Hardware Characteristics 19

C53000-G5040-C002-K, Edition 11.2020
Introduction
1.1 Advantages of SIPROTEC 5
1.1 Advantages of SIPROTEC 5

The devices in the SIPROTEC 5 series are based on the many years of experience gathered with SIPROTEC 4.
Extensive improvements have also been integrated. Take note of the differences between the modular and
non-modular systems.
The SIPROTEC 5 series is based on a newly developed, flexible modular system that is applicable to all the
devices. This results in the following advantageous new features:
• You save time because of jumperless devices.

You can set the rated current ranges (1 A, 5 A) electronically. You do not need to open the devices to do
this. You can set the thresholds of the binary inputs by setting parameters.
• The freely configurable, modular device design creates more flexibility.

You can configure your own device variants in addition to the standard variants. The modular system
consists of base and expansion modules, and optional plug-in modules. Thus, you can combine the
devices exactly as desired, and the standard variants are expandable. Devices with a size of up to 2-row
19-inches are possible.
• You save time because of prewired terminal blocks.

The terminal blocks for connection of the relays, of the binary inputs and outputs and of the current and
voltage transformers can be removed and fitted again while wired. This enables the possibility of pre-
wiring in the cabinet construction phase. Device replacement is uncomplicated and is possible in a short
time.
• You do not need to open the device to install and replace plug-in modules.
The slots for the plug-in modules are externally accessible. Communication modules and measuring-
transducer modules (for example, 4 x 20-mA measuring-transducer input) can be plugged in at these
plug-in module positions.
• Operation is uncomplicated and intuitive.

For all modular devices, it is possible to select whether to use a large graphical display, a small display, or
no display. The non-modular devices are available with large or small graphical display. The key switches
on the expansion module can be selected optionally. The 9 function keys enable a safe and uncompli-
cated procedure for important operator actions.
• Multi-colored LEDs ensure safe system management.

The 16 LEDs on the base module are 2-colored (green/red). Thus, the status of a signal (OK/disrupted)
can be shown clearly, for example. There can also be 16 red LEDs on each expansion module.
• Up to 40 analog channels per device create a greater scope of functions than in SIPROTEC 4.
Thus, even complex applications such as the 1 1/2 circuit-breaker layout are possible.
NOTE
i For the central busbar protection 7SS85, up to 80 analog channels are possible.

C53000-G5040-C002-K, Edition 11.2020
Introduction
1.2 Modular Systems and Hardware Characteristics

The SIPROTEC 5 series includes both modular and non-modular devices.
Modular devices consist of a base module (1/3 of 19 inches) and can be expanded with expansion modules
(1/6 of 19 inches). The device type identifier for modular devices is XXX85, XXX86, or XXX87, for example,
7SA86.
Type xxx84 devices have the same hardware properties as the modular devices, but they cannot be expanded
with expansion modules.
All non-modular devices consist of just a base module (1/3 of 19 inches) and cannot be expanded with expan-
sion modules (1/6 of 19 inches). The device type identifier for non-modular devices is 7XX81 or 7XX82, for
example 7SJ81 and 7SJ82.
Modular System for Modular Devices

The system is based on a modular structure. A modular device always consists of a base module and optionally
of expansion modules. The modules can be selected according to hardware characteristics. These characteris-
tics are:
• Module size
• Type of construction
• Fastening of the on-site operation panel
• Operation of the on-site operation panel
• Input and output module
• Plug-in modules
The modules are available in 2 sizes:
• Base module (1/3 of 19 inches)
• Expansion module (1/6 of 19 inches)

The devices are available in 3 designs: These are:
• Flush-mounting devices with on-site operation panel fitted directly on the device
• Surface-mounted devices with integrated on-site operation panel
• Surface-mounted devices with detached on-site operation panel

The on-site operation panels of the base modules can be selected from 3 variants:
• With a large display, keypad with function keys and 16 two-colored LEDs
• With a small display, keypad with function keys and 16 two-colored LEDs
• Without a display, without a keypad (standard), but with 16 two-colored LEDs

The on-site operation panels of the expansion modules can be selected from 3 variants:
• With 16 monochrome LEDs and 2 key switches
• With 16 monochrome LEDs
• With 8 LEDs and 8 function keys
• Without display elements

The base modules always contain the power-supply module PS201 and an input and output module IO2XX.
The expansion modules contain an input and output module IO2XX or a plug-in module assembly with inte-
grated power supply CB202. The 1st expansion module in the 2nd device row always contains the power-
supply module PS203.
The plug-in modules are available for various applications. Plug-in modules can be installed in 1 base module
or in 1 expansion module with 1 plug-in module assembly with integrated power supply CB202. You can find
more information on the available plug-in module types in chapter 4 Plug-In Modules.

C53000-G5040-C002-K, Edition 11.2020
Introduction
Hardware Characteristics for Non-Modular Devices (7xx81)

A non-modular device always consists of just 1 module (1/3 of 19 inches) and cannot be expanded with
expansion modules (1/6 of 19 inches). The hardware characteristics are:
• Module size: 1/3 of 19 inch
• Type of construction: Flush-mounting devices with on-site operation panel fitted directly on the device
The on-site operation panels can be selected from 2 variants:
• With a large display, keypad without function keys and 12 two-colored LEDs
• With a small display, keypad without function keys and 12 two-colored LEDs
The module always contains the power-supply module PS101 and an input and output module IO10X. The
input and output module IO10X includes the terminals for current and voltage transformers. Optionally, the
module can be equipped with an additional input and output module IO112 or IO113 for extra binary inputs
and outputs.
The plug-in modules are available for various applications. You can find more information on the available
plug-in module types in chapter 4 Plug-In Modules.
Hardware Characteristics for Non-Modular Devices (7xx82)

A non-modular device always consists of 1 module (1/3 of 19 inches) and cannot be expanded with expansion
modules (1/6 of 19 inches). The hardware characteristics are:
• Module size: 1/3 of 19 inch
• Type of construction: Flush-mounting devices with on-site operation panel fitted directly on the device
The on-site operation panels can be selected from 2 variants:
• With a large display, keypad with function keys and 16 two-colored LEDs
• With a small display, keypad with function keys and 16 two-colored LEDs
The module always contains the power-supply module PS101 and an input and output module IO10X. The
input and output module IO10X includes the terminals for current and voltage transformers. Optionally, the
module can be equipped with an additional input and output module IO110 for extra binary inputs and
outputs, or with a temperature measurement module IO111 (for 7SK82 only).
The plug-in modules are available for various applications. You can find more information on the available
plug-in module types in chapter 4 Plug-In Modules.

C53000-G5040-C002-K, Edition 11.2020
2 Forms of Devices and On-Site Operation Panels
2.1 Flush-Mounting Devices 22

2.2 Surface-Mounted Devices with Integrated On-Site Operation Panel 31
2.3 Surface-Mounted Devices with Detached On-Site Operation Panel 37
2.4 On-Site Operation Panels 41

C53000-G5040-C002-K, Edition 11.2020
Forms of Devices and On-Site Operation Panels
2.1 Flush-Mounting Devices
2.1.1 Description
The flush-mounting devices were conceived for installation in 19-inch racks or special openings in control
desks and cabinets. The on-site operation panel is linked permanently to the device.
Base Module
[le_surface_mounting_front, 3, --_--]
Figure 2-1 Front View – Standard
(1) USB connection, type B

(2) On-site operation panel
(3) Bus terminal for expansion module, only possible for modular devices
(4) Keypad with function keys

C53000-G5040-C002-K, Edition 11.2020
[le_surface_mounting_front_7SJ81, 1, --_--]
Figure 2-2 Front View – 7xx81
(1) USB connection, type B

(3) Bus terminal for expansion module, only possible for modular devices
(4) Keypad without function keys

C53000-G5040-C002-K, Edition 11.2020
[le_rear modular device, 3, --_--]
Figure 2-3 Rear View of a Modular Device, Terminals of a Typical Device with IO202
(1) Current terminal 1A

(2) Spring clip
(3) Voltage terminal 1B
(4) Voltage terminal 1C
(5) Voltage terminal 1D
(6) Protective grounding terminals
(7) Plug-in module position F
(8) Terminal for COM link K
(9) Terminal for integrated Ethernet interface J
(10) Battery compartment
(11) Plug-in module position E
(12) Terminal for detached on-site operation panel H
(13) Terminal for time synchronization G
(15) For module fastening inside the device, no user function (existence depending on the device
version)

C53000-G5040-C002-K, Edition 11.2020
[le_rear non modular, 3, --_--]
Figure 2-4 Rear View of a Non-Modular Device (7xx81, 7xx82), Terminals of a Typical Device with IO102
(1) Current terminal A

(2) Spring clip
(3) Voltage terminal B
(4) Voltage terminal D
(7) Plug-in module position F (not applicable to 7xx81)
(10) Time synchronization G
(11) Voltage terminal L
(12) For module fastening inside the device, no user function

C53000-G5040-C002-K, Edition 11.2020
Fastening Openings of the Base and 1/3 Module

To remove the screw covers, introduce the screwdriver into the provided slot.
[dw_screwdriver, 1, --_--]
Figure 2-5 Slot for Introducing the Screwdriver
Loosen the cover by turning slightly. Then pull off the cover to the front.
[le_osobep, 1, --_--]
Figure 2-6 Fastening Openings of the Base and 1/3 Module Shown, for Example, on the Top Fastening
(1) Screw cover

(2) Fastening opening
NOTICE
The screw cover can be damaged if improperly removed.
Noncompliance with the specified safety instructions means that material damage can occur.
² Use a screwdriver to remove the screw cover.

C53000-G5040-C002-K, Edition 11.2020
Expansion Module
[le_front expansion module, 1, --_--]
Figure 2-7 Front View of the Expansion Module
(1) Device housing

(3) Bus terminal for an additional expansion module (shown with bus termination plate)
Unused bus terminals are sealed with a cover.

C53000-G5040-C002-K, Edition 11.2020
[le_rear expansion module, 1, --_--]
Figure 2-8 Rear View of the Expansion Module
(1) Current terminal xA

(2) Spring clip
(3) Voltage terminal xB
(4) Bus terminal to the base module
(5) Voltage terminal xC
(6) Voltage terminal xD
NOTE
i It is possible to install these modules in the 1st and 2nd device row. x corresponds to the slot in the 19-inch
rack.
Possible values in the 1st device row: x = 3, 4, 5, or 6
Possible values in the 2nd device row: x = 8, 9, 10, 11 or 12

C53000-G5040-C002-K, Edition 11.2020
Counting Method for Modules in 19-Inch Rack (View of the Rear of the Device)
[dwbgrpos-170713-01.tif, 3, en_US]
Figure 2-9 Counting Method for Modules in 19-Inch Rack (Example)

(2) Voltage terminal A, B, C, D
(3) Terminal for time synchronization G
(4) Plug-in module E, F
(8) Terminal for COM link K
(9) 2-pole terminal to connect power supply
(10) Base module 1/3 of 19 in
(11) Expansion module 1/6 of 19 in
(12) Connecting cable between 1st and 2nd device row

C53000-G5040-C002-K, Edition 11.2020
NOTE
i The structure of the 2nd device row is described in chapter 5.2.1.3 Expanding Devices with 2nd Device
Row.
Connection Systems
[le_connection, 1, --_--]
Figure 2-10 Connection Systems
(1) Cut-out for contact tab

(2) Contact tab (prefitted on the expansion module)
(3) Hinged angle clip
(4) Snap-in spring
NOTE
i All on-site operation panels must be connected to one another via the bolt-on contact tabs. The contact
tabs are delivered with the expansion modules.

C53000-G5040-C002-K, Edition 11.2020
2.2 Surface-Mounted Devices with Integrated On-Site Operation Panel
2.2.1 Description of the Modular Device
NOTE
i The basic device structure is described in chapter 2.1.1 Description .
The surface-mounting devices with integrated on-site operation panel were conceived for fitting on a flat wall
surface. The on-site operation panel is fastened on the device with a distance frame. The distance frame
creates the necessary wiring space for the cable connections.
Base Module
[le_device mounting, 2, --_--]
Figure 2-11 Device Structure
(1) Outer distance frame

(2) Fixing bracket

C53000-G5040-C002-K, Edition 11.2020
[dwauzeil-040211-01.tif, 2, --_--]
Figure 2-12 Basic and Expansion Module of the Surface-Mounting Device
(1) Mounting bracket
NOTE
i When a base module is expanded, 2 mounting brackets must be fitted between the on-site operation
panels and the distance frame. The mounting bracket stabilizes the device. The length of the mounting
bracket corresponds to the width of the device.

C53000-G5040-C002-K, Edition 11.2020
Fastening Openings
[dwbaaube-040211-01.tif, 2, --_--]
Figure 2-13 Fastening Openings of the Base Module
(1) Top fastening openings

(2) Bottom fastening openings
2.2.2 Description of the Non-Modular Surface-Mounted Device
NOTE
The non-modular device variant is designed for mounting to a flat wall surface. This variant is created by flush-
mounting the non-modular device into the surface-mounting bracket. In this process, you may face the
opening as needed upward (cables coming from above) or downward (cables coming from below) as shown
in the following figure. You can order the surface-mounting bracket individually.

C53000-G5040-C002-K, Edition 11.2020
[le_device with console above and below, 1, --_--]
Figure 2-14 Bracket with the Opening Upward (Left) and the Opening Downward (Right)
(1) Flush-mounting device

(2) Bracket for the surface-mounting variant
(3) Bracket opening for cable entry or exit when mounting or dismantling the device

C53000-G5040-C002-K, Edition 11.2020
[sc device mounting, 2, --_--]
Figure 2-15 Surface-Mounted Version of the Non-Modular Device, Mounted

C53000-G5040-C002-K, Edition 11.2020
Fastening Openings
[sc fixing console, 2, --_--]
Figure 2-16 Fastening Openings of the Bracket

C53000-G5040-C002-K, Edition 11.2020
2.3 Surface-Mounted Devices with Detached On-Site Operation Panel
2.3.1 Description
NOTE
The surface-mounted devices with detached on-site operation panel are a variant of the surface-mounted
devices with an integrated on-site operation panel. The essential difference is that you can fit the on-site oper-
ation panel separately from the device. The distance frames are not assembled in this device type.
Base Module
The distance between the installation location of the device and that of the on-site operation panel is limited
to not more than 5 m (196.85 in) by the length of the connecting cable. The on-site operation panel must be
grounded. You can find information about grounding in chapter Grounding an On-Site Operation Panel,
Page 181.
NOTE
i Cables with a length of 5 m (196.85 in) are only specified for PCs and laptop computers with a USB2
connection. These cables are not specified for PCs and laptop computers with a USB3 connection.
Cables with a length of 2.5 m (98.43 in) are specified for USB2 and USB3 connections.

C53000-G5040-C002-K, Edition 11.2020
[le_device mounting base module, 2, --_--]
Figure 2-17 Device Structure of the Base Module
(1) Top fixing bracket

(2) Cover
(3) Bottom fixing bracket
(4) Connecting cable between the base module and the on-site operation panel
(5) Rear plate of the on-site operation panel

C53000-G5040-C002-K, Edition 11.2020
Fastening Openings
[dwbaaube-040211-01.tif, 2, --_--]
Figure 2-18 Device Structure of the Base Module
(1) Top fastening openings with fastening screw

(2) Bottom fastening openings with fastening screw

C53000-G5040-C002-K, Edition 11.2020
[dwosobb1-040211-01.tif, 2, --_--]
Figure 2-19 Fastening Openings for the On-Site Operation Panel
(1) Screw cover (pull towards you to remove)

(2) Fastening opening
(3) Fastening opening with fastening screw

C53000-G5040-C002-K, Edition 11.2020
2.4 On-Site Operation Panels
2.4.1 Description
Operating Concept
The operating concept is based on 4 groups:
• Navigation in the menu tree
• Modification of settings
• Display of measured values and protocols
• Control function from menu bar or control display

Operating personnel are informed about the current state of important measured data, indications, and
parameters. The data can be read out. You can perform parameterization and switching operations directly on
the device.
User Interface Language

You can set the user interface language to the following:
• Local language
• US English
Variants
Corresponding to the equipment configuration, 3 variants are available for each size. In the case of the non-
modular devices, only the front variants with small and large display are available.
[dwvaosop-080211-01.tif, 3, --_--]
Figure 2-20 Variants 1/3 Views

C53000-G5040-C002-K, Edition 11.2020
[dw_osop_with_pushbutton, 2, --_--]
Figure 2-21 Variants 1/6 Views

C53000-G5040-C002-K, Edition 11.2020
2.4.2 Overview of Operating Elements and Display Elements
On-Site Operation Panel of the Base 1/3 Module
[le_base_module, 3, --_--]
Figure 2-22 Base 1/3 Module in Standard Design, US Design (a), China Design (b), and for 7xx81 (c)
(1) Operating state display

(2) Display in 2 design versions
(3) Keypad with navigation keys
(4) Softkey
(5) Keypad with numeric keys and shiftable function keys (for 7xx81: without function keys)
(6) Keypad of control keys
(7) USB-port cover
(8) Cover labels

C53000-G5040-C002-K, Edition 11.2020
(9) Reset and LED test key

(10) 16 two-colored LEDs (for 7xx81: 12 two-colored LEDs)
The on-site operation panels are distinguished by the following characteristics:
• Flat and compact design
• LCD (Liquid Crystal Display) graphics display

Small with 192 x 128 pixels for showing measured values and small control displays
Large with 240 x 320 pixels for showing measured values and control displays
• Membrane keypad
• Menu navigation function keys (not for 7xx81)
• USB port, type A for notebook/PC
• 16 two-colored LEDs (parameterizable)

For 7xx81: 12 two-colored LEDs
The operating elements and display elements of the on-site operation panel for base modules are explained in
the following table.
Operating Element/ Function
Display Element
Testing LED functionality and resetting the LEDs to the original state
Softkey for confirming command prompts

On the left and right underneath the display
Keypad with navigation keys for navigating in the menus or in the graphical
displays (control displays)
Keypad with numeric keys for the entry of values and with programmable func-
tion keys for fast execution of actions
Next to the keypad, there are labeling strips for user-defined labels.
Keypad with numeric keys for entering values
Activating the function keys

C53000-G5040-C002-K, Edition 11.2020
Operating Element/ Function

Display Element
Control key for activating the control display
Control key for activating the switching object
Control key for deactivating the switching object
Display of operability
Run: ready to operate, the green LED is lit.
Error: not ready to operate, the red LED is lit.
USB port with protective cover
Type B for notebook/PC
16 two-colored parameterizable LEDs

C53000-G5040-C002-K, Edition 11.2020
On-Site Operation Panel of Expansion Modules
[le_expansion modules, 1, --_--]
Figure 2-23 Expansion Module
(1) 16 monochrome LEDs

(2) Cover labels
(3) 2 key switches
(4) 8 monochrome LEDs
(5) 8 push-buttons
The on-site operation panels are distinguished by the following characteristics:
• Flat and compact design
• 16 monochrome parameterizable LEDs
• Decorative film
• 2 key switches for setting the operating mode

Besides the base module, you can add an expansion module with key switches. The following table explains
the meanings of the switch positions.

C53000-G5040-C002-K, Edition 11.2020
Operating Element/ Meaning

Display Element
16 monochrome parameterizable LEDs
Local: On-site operation

Remote: Remote control
Interlocking OFF: Unlocked operation

Normal: locked operation with the configured interlocking conditions
The on-site operation panel with push-buttons is equipped with 8 LEDs and 8 function keys. It can be used as
an on-site operation panel by almost all the I/O modules (except for the modules IO230, IO231). The push-
button module must be placed at position 3 in the 1st row. If the device has a key switch, then the push-
button module must be placed at position 4 in the 1st row. One push-button module is permitted per device.
Operating Element/ Meaning
Display Element
8 monochrome parameterizable LEDs
Keypad with programmable function keys for fast execution of actions. Next to
the keypad, there are labeling strips for user-defined labels.

C53000-G5040-C002-K, Edition 11.2020
C53000-G5040-C002-K, Edition 11.2020
3 Electronic Modules
3.1 Power-Supply Modules of the Modular Devices 50

3.2 Input and Output Modules of the Modular Devices 64
3.3 Power-Supply Module of Non-Modular Devices (7xx81, 7xx82) 124
3.4 Input and Output Modules of Non-Modular Devices (7xx81, 7xx82) 128

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.1 Power-Supply Modules of the Modular Devices
3.1.1 Function Description of the Power-Supply Modules of the Modular Devices
Module Designation Function Description

PS201 • Power-supply module
• Plug-in module assembly
• DC 24 V/DC 48 V or
DC 60 V to 250 V and AC 100 V to 230 V
• In the base module 1/3 of 19 in
• Assembled with 3 binary inputs, 2 binary outputs, and one status life contact
PS203 • Power-supply module for supplying the 2nd device row
• In the expansion module, 1/6 of 19 in
PS204 • Power-supply module as redundancy for the printed circuit board assemblies
PS201 and PS203
CB202 • Plug-in module assembly with internal power supply
3.1.2 Power-Supply Module PS201
3.1.2.1 Description
The power-supply module PS201 is always permanently installed in the base module. The central task is to
supply power to all modules. The following can be found on the PS201 module:
• 2 positions for plug-in modules (communication modules, measuring-transducer modules)
• Terminals for time synchronization, the on-site operation panel, an integrated Ethernet interface, and a
COM link interface
• A 14-pole voltage terminal (3 binary inputs and 3 binary outputs)
• Battery for the CPU.

The power supply of the other modules is established automatically through the plug-in bus connection when
they are assembled.
The following 2 variants are available for the rated voltage range:
• DC 24 V to 48 V
• DC 60 V to DC 250 V and AC 100 V to AC 230 V (50 Hz and 60 Hz)

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.1.2.2 Terminals
Overview of Terminals
[le_ps201, 3, --_--]
Figure 3-1 PS201 – Terminals

(5) Integrated Ethernet interface J
(6) COM link K, connection to the CB202 plug-in module assembly, position K

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
Terminal and Connection Diagram
[cdps201x-270912-01.tif, 1, en_US]
Figure 3-2 PS201 – Terminal Diagram

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdps201x-270812-01.tif, 1, en_US]
Figure 3-3 PS201 – Connection Diagram
Time-Synchronization Terminal
The terminal for time synchronization is located on the D-sub 9 interface (position G). Time synchronization
signals for DC 5 V, DC 12 V, and DC 24 V can be processed as an option.
For further information on connecting to the time synchronization, see chapter 6.6 Communication Interfaces
in the Technical Data.
On-Site Operation Panel Terminal

The terminal for the on-site operation panel of surface-mounted devices is located on the D-sub 15 interface
(position H). The on-site operation panel of surface-mounted devices with the on-site operation panel inte-
grated or detached is connected to this interface.
For further information on connecting to the on-site operation panel, see chapter 6.6 Communication Inter-
faces in the Technical Data.
Integrated Ethernet Interface J(RJ45)

This terminal is used to load the device with DIGSI 5 using Ethernet. This terminal also enables straightforward
IEC 61850 Ethernet communication or communication with another protocol via Ethernet, for example, for
connecting an external RTD unit.
For further information on the integrated Ethernet interface, see chapter 6.6 Communication Interfaces in the
Technical Data.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
Ethernet COM Link

The Ethernet connection to the CB202 plug-in module assembly with integrated power supply is realized using
the RJ45 interface.
The RJ45 interface can be used exclusively for the connection of the CB202 plug-in module assembly. This
terminal is left unused when no CB202 plug-in module assembly is in use.
For further information on the Ethernet COM link, see chapter 6.6 Communication Interfaces in the Technical
Data.
3.1.3 Power-Supply Module PS203 for the 2nd Device Row
3.1.3.1 Description
If you expand the device into the 2nd device row, you need the PS203 power-supply module.
NOTE
i The PS203 power-supply module is always supplied with the expansion module and must always be
mounted at position 7.
Up to 5 additional expansion modules are possible in the 2nd device row. The scope of delivery of the PS203
power-supply module includes 1 connecting cable for the 2nd device row, 1 angle rail, 1 sealing panel and 1
adaptor bracket.
The PS203 power-supply module has no additional functionality. It is used exclusively to supply power to the
2nd device row.
The rated voltage variant of the PS203 power-supply module must always match the PS201 power-supply
module of the base module.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.1.3.2 Terminals
[le_ps203, 2, --_--]

(2) LED: Power On
Connection Diagram
[tdps203x-030713-01.tif, 2, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[dwkl2pol-030211-01.tif, 1, --_--]
Figure 3-6 Connection of External Power Supply
NOTE
i When expanding a device with the 2nd device row, you must install the connecting cable for the 2nd
device row with the corresponding angle rail. All required components are included in the scope of delivery
of a power-supply module PS203.
[dw_kabel1-020414-01, 1, --_--]
Figure 3-7 Connecting Cable for the Connection of a 2nd Device Row
(1) Handle mold for the connection to the 1st device row
(2) Handle mold for the connection to the 2nd device row
[dw_winkel-020414-01, 1, --_--]
Figure 3-8 Sealing Plate and Adaptor Bracket for the Expansion Module of the 1st Device Row

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
(1) Device bus of the outermost right expansion module of the 1st device row
(2) Sealing plate
(3) Adaptor angle
(4) 2 fastening screws
[dw_schiene-020414-01, 1, --_--]
Figure 3-9 Angle Rail
(1) Angle rail

(2) 2 rubber seals
3.1.4 Power-Supply Module PS204 for Redundant Power Supply
3.1.4.1 Description
If you want to equip a SIPROTEC 5 device with a redundant power supply, you need the power-supply module
PS204. For devices with a 2nd row, a 2nd PS204 module is necessary additionally to the PS203 module.
The power-supply module PS204 has no additional functionality. It functions exclusively as a redundant power
supply in the device and is only active if the main power supply or its auxiliary voltage supply fails.
The rated-voltage variant of the power-supply module PS204 must always match the power-supply module
PS201 of the base module.
Device Prerequisites for Redundancy
• The base module must be device version C or later. You can find the device version on the name plate
(see the figure in the chapter 6.15 Modular Device Name Plate). For older devices (older than release
status C), it is not possible to achieve redundancy by retrofitting a PS204.
• The firmware and configuration of the device must be version V7.82 or higher.
NOTE
i The CB202 PCB assembly is not supported by the redundant power supply. If the power supply of the
CB202 fails, a PS204 in the device does not function as a redundant power supply. The device goes into
fallback mode.
3.1.4.2 Positioning Specifications

The power-supply module PS204 is always provided as part of the expansion module and must always be
mounted on the very right position (front view) in the corresponding row, for example, at position 3 for a 1/2
device.
Example Installation of the PS204 in a 2-Row Device with Complete Configuration
• 1st device row:

– Mounting position 1: IO2xx
– Mounting position 2: PS201
– Mounting positions 3 to 5: IO2xx

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
• 2nd device row:

– Mounting positions 8 to 11: IO2xx
[dw_module_position_PS204, 1, en_US]
Figure 3-10 Arrangement of Modules with 2 PS204 Modules – Rear View
There is an exception if a CB202 PCB assembly with integrated power supply is to be used: The CB202 PCB
assembly with integrated power supply must always be positioned to the right (front view) of the PS204
module in the 1st or 2nd row.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
Example Installation of the PS204 with a CB202 in a 1-Row Device with 5/6 Configuration
• 1st device row:

– Mounting position 5: CB202
[dw_module_position_PS204_w_CB202, 1, en_US]
Figure 3-11 Arrangement of Modules with PS204 Module and a CB202 – Rear View

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.1.4.3 Terminals
[le_ps204, 1, --_--]

(2) LED: Power On
(3) Protective grounding terminal
Connection Diagram
[tdps204x, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[dwkl2pol-030211-01.tif, 1, --_--]
3.1.5 Plug-In Module Assembly with Integrated Power Supply CB202
3.1.5.1 Description
The plug-in module assembly CB202 is a PCB assembly with an internal power supply. The plug-in module
assembly CB202 is used in an expansion module. 3 plug-in module positions (M, N and P) are available for
installation of plug-in modules. The plug-in modules can be installed in the following arrangements:
Plug-In Module Position
M N P
Configured with Measuring-transducer Measuring-transducer Measuring-transducer
3 measuring-transducer module module module
modules
Configured with Measuring-transducer Measuring-transducer Communication module
2 measuring-transducer module module
modules and Measuring-transducer Communication module Measuring-transducer
1 communication module module module
Configured with Measuring-transducer Communication module Communication module
1 measuring-transducer module
module and
2 communication modules
Combinations that do not occupy all plug-in module positions are also possible.
NOTE
i A communication module cannot be plugged into the plug-in module position M.
The CB202 plug-in module assembly communicates with the base module using a communication connection.
This communication connection is established with a special connecting cable. This connecting cable
(CAT5 FTP patch cable) is always included in the scope of delivery of the CB202 plug-in module assembly and
need not be ordered separately.
• DC 24 V to 48 V
• DC 60 V to 250 V and AC 100 V to 230 V (50 Hz and 60 Hz)

The CB202 plug-in module assembly can be used in the 1st and 2nd device rows.
LEDs of the RJ45 Terminals

The light-emitting diodes (LEDs) signal the operating state of the communication connection. The operating
states are explained in the following table.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
COM Link (RJ45) Signal Color Operating State

LED 1 CL2_LED0_N Yellow Flashes when a communication module is inserted
in plug-in module position P.
LED 2 CL3_LED0_N Green Flashes when a communication module is inserted
in plug-in module position N.
3.1.5.2 Terminals
[le_cb202, 1, --_--]
Figure 3-15 CB202 – Terminals

(2) LED: Power On
(3) COM link
(4) Plug-in module position M (for measuring-transducer modules only – equipped in this example
with an ANAI module)
(5) Plug-in module position N (for measuring-transducer or communication modules)
(6) Plug-in module position P (for measuring-transducer or communication modules – equipped in
this example with an ETH-BA-2EL module)
The Ethernet connection to the base module is established at the COM link terminal.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
The 2-pole voltage terminal is used for the external power supply (see Figure 3-17).
Connection Diagram
[tdcb202x-100713-01.tif, 2, en_US]
Figure 3-16 CB202 – Connection Diagram
[dwkl2pol-030211-01.tif, 1, --_--]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2 Input and Output Modules of the Modular Devices
3.2.1 Function Description of the Input and Output Modules of the Modular Devices

IO201 • Input and output module
• 4 current measuring inputs, 8 binary inputs, 6 binary outputs
• 4 current measuring inputs, 4 voltage measuring inputs, 8 binary inputs,
6 binary outputs
• 10 binary inputs, 4 binary outputs, 4 power relays for controlling 2 motors
• 12 binary inputs, 16 binary outputs
11 binary outputs
• 8 binary inputs, 4 high-speed binary outputs (semiconductor accelerated)
• 4 current measuring inputs, 3 voltage measuring inputs, 4 high-speed meas-
uring-transducer inputs for current or voltage, 7 binary outputs
• 8 voltage inputs, 8 binary inputs
• 8 high-speed measuring-transducer inputs for current or voltage, 8 binary
inputs
5 binary outputs
• 4 current measuring inputs, 4 voltage measuring inputs (measuring range:
7.07 V), 8 binary inputs, 6 binary outputs
IO216 • Input module
• 16 special binary inputs with maximized robustness against electrical distur-
bances and failures
• 48 binary inputs
• 24 binary outputs

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

IO233 • Input module with special version for binary inputs. You can find more infor-
mation in chapter 6 Technical Data.
• 4 current measuring inputs (GIS LPIT Rogowski coil or LPCT)
• 4 voltage measuring inputs (GIS LPIT volt. or LPVT)
• 4 temperature inputs (PT100)
3.2.2 Input and Output Module IO201
3.2.2.1 Description
The terminals for the following are located on the input and output module IO201:
• 4 current transformers (optionally protection-class current transformers or instrument transformers)
• 8 binary inputs
• 6 binary outputs, of which:

– 4 high-speed make contacts (type F)
– 2 high-speed change-over contacts (type F)
The connections are distributed over:
• 1 x 8-pole current terminal
• 3 x 14-pole voltage terminal

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.2.2 Terminals
[dwio201p-030211-01.tif, 2, --_--]
Figure 3-18 IO201 – Terminals

NOTE
i x corresponds to the slot in the 19-inch rack.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

For the binary inputs and outputs, the x corresponds to the slot in the 19-inch rack.
[cdio201x-290812-01.tif, 1, en_US]
Figure 3-19 IO201 – Terminal Diagram

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio201x-290812-01.tif, 1, en_US]
Figure 3-20 IO201 – Connection Diagram
3.2.3.1 Description
• 4 voltage transformers
• 8 binary inputs


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.3.2 Terminals
[dwio202p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio202x-300812-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio202x-240812-01.tif, 1, en_US]
3.2.4.1 Description
• 4 binary inputs (2 binary inputs each with common connection)
• 4 binary outputs with 4 high-speed make contacts (type F)


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.4.2 Terminals
[le_io203, 1, --_--]

(2) Current terminal xB
NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio203x-280812-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio203x-110313-01.tif, 1, en_US]
3.2.5.1 Description
• 4 binary outputs with 4 standard make contacts (type S)
• 4 power relays for controlling 2 motors (forward/backward) with a common auxiliary voltage supply Vaux
+, Vaux-
The power relays operate in interlocked mode, that is, only one relay of each switching pair picks up at a
time thereby avoiding a power-supply short circuit. Note the polarity specified in the terminal and
connection diagram.
The connections are distributed over three 14-pole voltage terminals.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.5.2 Terminals
[dwio204p-201112-01.tif, 2, --_--]
(1) Voltage terminal xA

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio204x-201112-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio204x-201112-01.tif, 1, en_US]
3.2.6.1 Description

The connections are distributed over four 14-pole voltage terminals.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.6.2 Terminals
[dwio205p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio205x-260213-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio205x-240812-01.tif, 1, en_US]
3.2.7.1 Description
• 6 binary inputs

The connections are distributed over two 14-pole voltage terminals.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.7.2 Terminals
[dwio206p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio206x-280812-01.tif, 1, en_US]
[tdio206x-050313-02.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.8.1 Description

The connections are distributed over four 14-pole voltage terminals.
3.2.8.2 Terminals
[dwio207p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio207x-260213-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio207x-300812-01.tif, 1, en_US]
3.2.9.1 Description
• 4 binary inputs
• 11 binary outputs with 3 standard make contacts (type S), 6 high-speed make contacts (type F), and 2
high-speed change-over contacts (type F)
• 1 x 8-pole current terminal block
• 3 x 14-pole voltage terminal blocks

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.9.2 Terminals
[dwio208p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio208x-050313-01.tif, 3, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio208x-300812-01.tif, 1, en_US]
3.2.10.1 Description
• 8 binary inputs
• 4 binary outputs with semiconductor-accelerated make contacts (type HS)


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.10.2 Terminals
[dwio209p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio209x-110313-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio209x-270812-01.tif, 1, en_US]
• 4 high-speed measuring transducer inputs for current (20 mA) or voltage (10 V)

– 1 standard make contact (type S)
– 2 standard change-over contacts (type S)

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.11.2 Terminals
[dwio202p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cd_io210, 3, en_US]
(1) Voltage input MT3 with higher voltage immunity (maximum continuous voltage ± 60 V)

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[td_io210, 3, en_US]
• 8 voltage inputs
• 8 binary inputs

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.12.2 Terminals
[dwio211p-211112-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio211x-221112-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio211x-211112-01.tif, 1, en_US]
• 8 high-speed measuring-transducer inputs for current (20 mA) or voltage (10 V)
• 8 binary inputs

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.13.2 Terminals
[dwio204p-201112-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio212x, 2, en_US]
• 2 binary inputs
• 5 binary outputs with 4 high-speed make contacts (type F) and 1 high-speed change-over contact (type
F)

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.14.2 Terminals
[dwio214p-030211-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

[cdio214x-260213-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio214x-270812-01.tif, 1, en_US]
• 4 voltage transformers for the connection of an isolation amplifier P27000-H1-S011

Connect each phase of the device via this isolation amplifier with capacitive voltage transformers from
the Trench Co. The voltage input is specially designed for a measuring range of up to 7.07 V.
• 8 binary inputs

3.2.15.2 Terminals
The terminal and connection diagram is identical to the input and output module IO202 in the expansion
module.
You can find more information in chapter 3.2.3.2 Terminals, Figure 3-22 and Figure 3-23.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.16 Input Module IO216
• 16 special binary inputs with maximized robustness against electrical disturbances and failures
3.2.16.2 Terminals
[dwio204p-201112-01.tif, 2, --_--]

NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
The terminals for the following are located on the IO230 input module:
The connections are distributed over six 10-pole terminals.
NOTE
i The IO230 input module has a group switching for the switchover of threshold values. The threshold values
of the binary inputs can be switched in groups of 8 only:
• Group of 8 x.1, x.2, x.3, x.4, x.25, x.26, x.27, x.28

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.2.17.2 Terminals
[dwio230x-030713-01.tif, 2, --_--]
(1) Terminal xA
(2) Terminal xC
(3) Terminal xD
(5) Terminal xH
(6) Terminal xG
(7) Terminal xE
NOTE
NOTE
i The polarities of the voltages at the binary inputs must not be reversed!

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdio230x-030713-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
• 24 binary outputs, standard make contacts (type S)

The connections are distributed over six 10-pole connection terminals.
3.2.18.2 Terminals
[dwio230x-030713-01.tif, 2, --_--]
(1) Terminal xA
(2) Terminal xC
(3) Terminal xD
(5) Terminal xH
(6) Terminal xG
(7) Terminal xE
NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
NOTE
[cd_io231x, 2, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[td_tdio231x, 1, en_US]
The terminals for the following are located on the input module IO233:

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
The connections are distributed over six 10-pole terminals.
3.2.19.2 Terminals
[dw_io233x, 1, en_US]
(1) Terminal xA
(2) Terminal xC
(3) Terminal xD
(5) Terminal xH
(6) Terminal xG
(7) Terminal xE
NOTE
NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[td_io233x, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
The following terminals are on the input module IO240 for the low-power instrument transformer (LPIT):
• 4 current inputs for the low-power current transformers in the gas insulated switchgears (GIS LPCT), for
example, rogowski coils
• 4 voltage inputs for the low-power voltage transformers in the gas insulated switchgear (GIS LPVT), for
example, capacitive voltage sensors
• 4 temperature measuring channels (4-wire PT100 thermistor)

The connections are distributed over four 14-pole terminal blocks.
3.2.20.2 Terminals
[le_IO240_overview, 1, --_--]
(1) Current/Voltage/Temperature terminal xA

(2) Current/Voltage/Temperature terminal xB
(3) Current/Voltage/Temperature terminal xC
(4) Current/Voltage/Temperature terminal xD
(5) Protective grounding terminal
(6) LPIT cable shield
NOTE

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
Terminals and Connection Diagram

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[td_io240x, 3, en_US]
3.2.20.3 Connections of GIS-LPIT Sensors

When connecting the Siemens Energy GIS-LPIT sensors to the LPIT module IO240, proceed as follows:
² Use the delivered cable LEONI L45551-P42-B5 and confection the cable as explained in the user manual
of the LPIT GIS sensor.
The L45551-P42-B5 cable has 4 twisted pairs: 1 pair for the low-power voltages, 1 pair for the low-power
currents, and 2 pairs for the PT100 temperature sensor connection. Each conductor is terminated with a
wire ferrule (length = 12 mm, wire gauge = 0.5 mm2). Each internal shield is connected with a cable
ring-type lug (for M4 screw).
² Connect the signal cables to the corresponding terminals, refer to Figure 3-69.
² Connect the ring-type lugs of the shield terminals with M4 screws (torque = 1.6 Nm) to the marked
terminals (shield) at the rear plate of the LPIT module.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[sc_IO240 connection cables, 1, en_US]
Figure 3-71 Connection to Sensors with Cables
² Connect the unused terminals (2-4 and 12-14) with the cross connectors for voltage terminals, shown in
Figure 5-25.
² Slide the strain relief from the left toward the voltage terminals.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[sc_IO240 connection strain release, 1, en_US]
Figure 3-72 Strain Relief from the Left
² Place the 4 cables over the fixation surface.

² Fix the strain relief to the rear plate of the LPIT module using 4 M4 screws (torque = 1.6 Nm).
² Mount the clamps for fixing the cables to the strain relief using 8 M4 screws (torque = 1.6 Nm).

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[sc_IO240 connection clamps, 1, en_US]
Figure 3-73 Clamps for Fixing the Cables
NOTICE
The isolation of the cables can be damaged if you are careless when mounting the clamps.
Noncompliance with the specified safety instructions means that material damage can occur.
² Be careful when mounting the clamps to protect the isolation of the cables.
² Connect the LPIT module with the module or base unit on the right side of the LPIT module, using the
provided PE cable. If there are additional IO modules, connect them using their PE cables to the upper PE
screw of the LPIT module (torque = 1.6 Nm).

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[sc_IO240 connection PE connection, 1, en_US]
Figure 3-74 Connection of PE
² Mount the shield cover with the supplied slotted capstan screws (torque = 1.2 Nm). To avoid unauthor-
ized access to the terminal connections, the screw provides a hole and the cover provides a lug for
applying a seal.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[sc_IO240 connection seal cage, 1, en_US]
Figure 3-75 Mounting the Shield Cover

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.3 Power-Supply Module of Non-Modular Devices (7xx81, 7xx82)
3.3.1 Power-Supply Module PS101
3.3.1.1 Description
The power-supply module PS101 is always permanently installed in the 1/3 module. The following can be
found on the PS101 module:
• 2 positions for plug-in modules (communication modules, measuring-transducer modules)
• Terminals for time synchronization and an integrated Ethernet interface
• A 14-pole voltage terminal (3 binary inputs, 3 binary outputs and connection for power supply)
• Battery for the CPU

• DC 24 V to 48 V
• DC 60 V to 125 V
• DC 110 V to DC 250 V and AC 100 V to AC 230 V (50 Hz and 60 Hz)

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.3.1.2 Terminals
The terminals assigned to the module are identified by the frame in the figure.
[le_ps101, 2, --_--]
(1) Voltage terminal L


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdps101x-210513-01.tif, 1, en_US]
Figure 3-77 PS101 – Terminal Diagram
[tdps101x-210513-01.tif, 1, en_US]
Time-Synchronization Terminal

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
For further information on connecting to the time synchronization, see chapter 6.6 Communication Interfaces
in the Technical Data.
Integrated Ethernet Interface (RJ45)

This terminal is used to load the device with DIGSI 5 using Ethernet. This terminal also enables straight-
forward IEC 61850 Ethernet communication (including GOOSE) or communication with another protocol via
Ethernet, for example, for connecting an external RTD unit.
For further information on the integrated Ethernet interface, see chapter 6.6 Communication Interfaces in the
Technical Data.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4 Input and Output Modules of Non-Modular Devices (7xx81, 7xx82)
3.4.1 Function Description of the Input and Output Modules of the Non-Modular
Devices

6 binary outputs
• 12 temperature inputs
3.4.2.1 Description
• 4 current transformers (3 transformers always as protection-class current transformers, the 4th optionally
as protection-class or instrument transformer)
• 8 binary inputs

– 4 standard make contacts (type S)

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4.2.2 Terminals
[le_io101, 2, --_--]


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdio101x-220513-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio101x-220513-01.tif, 1, en_US]
3.4.3.1 Description
• 4 current transformers (3 transformers always as protection-class current transformers, the 4th optionally
as protection-class or instrument transformer)
• 8 binary inputs


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4.3.2 Terminals
[le_io102, 2, --_--]


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdio102x-220513-01.tif, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio102x-220513-01.tif, 1, en_US]
3.4.4.1 Description
• 8 current transformers (optionally as protection-class current transformers or instrument transformers)
• 4 binary inputs (2 binary inputs each with common connection)


C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4.4.2 Terminals
[le_io103, 2, --_--]

(2) Current terminal B

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdio103x-131113-01, 3, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio103x-01.vsd, 1, en_US]
3.4.5.1 Description

• 1 x 10-pole terminal

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4.5.2 Terminals
[le_io110, 3, --_--]
(1) Terminal M
(3) Terminal N

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdio110x-220513-01.tif, 3, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[tdio110x-220513-01.tif, 1, en_US]
3.4.6.1 Description
• 12 temperature inputs

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4.6.2 Terminals
[le_io111, 2, --_--]
(1) Terminal M
(3) Terminal N

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[td_io111, 1, en_US]
3.4.6.3 Connections of Temperature Sensors and Cables
Connections of Temperature Sensors Directly to the Device

It is possible in principle to connect temperature sensors with 2-phase or 3-phase technology. To achieve the
specified accuracy, Siemens recommends only using 3-phase technology.
[dw_example_temp_sensor_3phase, 2, en_US]
Figure 3-94 Example: Connecting Temperature Sensors RTD 1 (3-Line Terminal) and RTD 2 (3-Line
Terminal) to Terminals M1 to M5
² For a connection with 2-phase technology, you must connect a bridge, for example for RTD 2, between
M3 and M4.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[dw_example_temp_sensor_2phase, 2, en_US]
[dw_temperature_sensor, 2, en_US]
Connecting the Lines

When connecting the lines, proceed as follows:
² Use shielded lines with shielding braid (3-core AWG 24).
² Prepare the cable as shown in the following figure.
The dimensions in the drawing are designed so that the plug can still be plugged in with the shielding
plate screwed on.
[dw_shielded_line, 1, en_US]
Figure 3-97 Preparing the Cable
² Connect the lines with bootlace ferrules.

² Use the included clamps and cable ties to make contact with the cable shield and provide strain relief on
the cable.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[sc_ shielding_plate _mounting-cutout, 1, --_--]
Figure 3-98 Using Clips and Cable Ties
² Loosen the 2 screws for fastening the shielding plates on the device next to the 16-pole or 17-pole plug
so that there is somewhat more than 2 mm (0.08 in) space.
² Push the prepared shielding plate under the screw heads and tighten them.
² Plug in the plug and secure it with its 2 outer screws.
[le_ shielding_plate _screw fastening, 1, --_--]
Figure 3-99 Fastening with Screws
(1) Fastening screws for shielding plate
² Repeat the steps for the 2nd plug.
3.4.7.1 Description
• 5 binary inputs

– 2 standard-make contacts (type S)

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4.7.2 Terminals
The overview of terminals is identical to the module IO110, see Figure 3-88.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdio112, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
3.4.8.1 Description
• 7 binary inputs

3.4.8.2 Terminals
The overview of terminals is identical to the module IO110, see Figure 3-88.

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules
[cdio113, 1, en_US]

C53000-G5040-C002-K, Edition 11.2020
Electronic Modules

C53000-G5040-C002-K, Edition 11.2020
4 Plug-In Modules
4.1 Function Description of Plug-In Modules of Modular and Non-Modular Devices 152
4.2 Communication Modules 153
4.3 Measuring-Transducer Modules 177

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
4.1 Function Description of Plug-In Modules of Modular and Non-Modular Devices
4.1 Function Description of Plug-In Modules of Modular and Non-

Modular Devices
Plug-In Module Function Description
Designation
USART-xx-yEL Serial communication module with electric transmission
USART-xx-yFO Serial communication module with optical transmission for short distance
USART-xx-yLDFO Serial communication module with optical transmission for long distance
ETH-xx-2EL Ethernet module with electric transmission
ETH-xx-2FO Ethernet module with optical transmission
ANAI-CA-4EL Measuring-transducer module
ARC-CD-3FO Module for connecting optical sensors for detecting arcs
xx 2 letters: Unique code for the module in the product code of the device
y 1 = 1 channel
2 = 2 channels

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
4.2 Communication Modules
4.2.1 Overview
SIPROTEC devices can be ordered with factory-installed communication modules. The communication modules
can also be installed and replaced in the SIPROTEC devices afterwards. You do not have to open the device for
this.
NOTE
i The communication modules available for reordering are not preconfigured. Use DIGSI 5 to carry out the
functional adjustment to the required protocol application.
The communication modules can be installed in the base module or the 1/3 module and in the expansion
module with the plug-in module assembly CB202. A maximum of 2 communication modules each can be
installed. You can use only one CB202 in the device.
The plug-in module assembly CB202 is a printed circuit board assembly with an integrated power supply.
The plug-in module assembly CB202 communicates with the base module via a special connecting cable. This
connecting cable (CAT 5 FTP patch cable) is always included in the scope of delivery of the plug-in module
assembly CB202 or the devices containing the plug-in module assembly CB202 and needs not be ordered
separately.
Ensure that you route the communication lines separately from network circuits.
[le_cm201p, 1, --_--]
Figure 4-1 Plug-In Module Positions and Communication Terminals in the Base Module, with Modular
Devices

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules

(6) Connection to expansion module with plug-in module assembly CB202
[le_lmnppo, 2, --_--]
Figure 4-2 Plug-In Module Positions and Communication Terminals in the Expansion Module with CB202

(2) COM link L (connection to interface K of the base unit)
(3) Plug-in module position M
(4) Plug-in module position N
(5) Plug-in module position P
NOTE
i You cannot insert any communication module at plug-in module position M. The plug-in module posi-
tion M is intended for a measuring-transducer module only.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
[le_slots and communication terminals, 2, --_--]
Figure 4-3 Plug-In Module Positions and Communication Terminals on the 1/3 Module, for Non-Modular
Devices (7xx81, 7xx82)

(3) Plug-in module position F (not applicable to 7xx81)
The following communication modules can be used for SIPROTEC 5:
• Serial modules
Application: Communication to the substation automation technology via substation-control protocols
Protection interface (only optical serial modules) for interfacing to external communication converters for
short direct connections.
2 different communication protocols or 2 different applications can be operated on serial modules with
2 connections. The IEC 60870-5-103 protocol for the substation automation technology as well as a
protection interface, for example, can be operated on a serial optical module for close range with
2 connections.
Assign the protocol application to the corresponding channel of the communication module with DIGSI 5.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
• Ethernet Modules
Application: Ethernet-based communication to the substation automation technology via substation-
control protocols (for example, IEC 61850 and DNP3)
– Secure communication to DIGSI 5
– Communication between the devices (IEC 61850-GOOSE)
– Synchrophasor protocol (IEEE C37.118 - PMU)
The modules can be operated with or without an integrated switch.
• Long-distance modules
Application: Direct protection interface communication over long distances using multimode or single-
mode optical fibers.
The designation of the modules corresponds to the following scheme, which is typically explained with the
module USART-AB-1EL. The module designation consists of 3 blocks.
1st block Type of module
USART = Serial module for short or long distance
ETH = Ethernet module
2nd block Unique code for the module in the product code of the device
The code consists of 2 letters.
3rd block Number and physical design of the connections
1 = 1 connection (1 channel)
2 = 2 connections (2 channels)
EL = Electrical connection
FO = Fiber-optic connection
LDFO = Long-distance transmission via optical fibers
4.2.2 Communication Applications of the Plug-In Modules
You can find information on communication applications for the plug-in modules in the following tables.
Plug-In Modules for the Communication
Table 4-1 Plug-In Modules for Applications with the Protection Interface and for Other Applications
USART-AH-1LDFO2
USART-AX-2LDFO4
USART-AY-2LDFO5
USART-AW-2LDFO
USART-AJ-1LDFO3
USART-AG-1LDFO
USART-AU-2LDFO
USART-AK-1LDFO
USART-AV-2LDFO
USART-AF-1LDFO
USART-AD-1FO
USART-AE-2FO
USART-AC-2EL
USART-AB-1EL
ETH-BD-2FO1
ANAI-CA-4EL
ARC-CD-3FO
ETH-BB-2FO
ETH-BA-2EL
Plug-In Module
Physical Connection
1 x electrical serial RS485, RJ45 ■
2 x electrical serial RS485, RJ45 ■
1 For modular devices only (not for 7ST85 and 6MD89)

2 USART-AH-1LDFO only in connection with USART-AJ-1LDFO or USART-AY-2LDFO
3 USART-AJ-1LDFO only in connection with USART-AH-1LDFO or USART-AX-2LDFO
4 USART-AX-2LDFO only in connection with USART-AJ-1LDFO or USART-AY-2LDFO
5 USART-AY-2LDFO only in connection with USART-AH-1LDFO or USART-AX-2LDFO

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
USART-AH-1LDFO2
USART-AX-2LDFO4
USART-AY-2LDFO5
USART-AW-2LDFO
USART-AJ-1LDFO3
USART-AG-1LDFO
USART-AU-2LDFO
USART-AK-1LDFO
USART-AV-2LDFO
USART-AF-1LDFO
USART-AD-1FO
USART-AE-2FO
USART-AC-2EL
USART-AB-1EL
ETH-BD-2FO1
ANAI-CA-4EL
ARC-CD-3FO
ETH-BB-2FO
ETH-BA-2EL
Plug-In Module
1 x optical serial, 820 nm, ST connector, ■

2 km via 62.5/125 μm multimode optical
fiber
2 x optical serial, 820 nm, ST connector, ■
2 km via 62.5/125 μm multimode optical
fiber
2 x electrical Ethernet 100 Mbit/s, RJ45, ■ ■
20 m 6
2 x optical Ethernet 100 Mbit/s, ■

1300 nm, LC connector, 24 km via 6
9/125 μm singlemode optical fiber
2 x optical Ethernet 100 Mbit/s, ■ ■
1300 nm, LC connector, 2 km via
50/125 μm or 62.5/125 μm multimode
optical fiber
1 x optical serial, 1300 nm, LC ■
connector, 24 km via 9/125 μm single-
mode optical fiber or 4 km via 62.5/125
μm multimode optical fiber
mode optical fiber or 4 km via 62.5/125
μm multimode optical fiber
mode optical fiber
mode optical fiber
mode optical fiber
mode optical fiber
1 x optical serial, bidirectional via ■
1 common optical fiber, 1300 nm/
1550 nm (Tx/Rx), 2 x LC simplex plug,
40 km via 9/125 μm singlemode optical
fiber2

6 For the 2 x electrical Ethernet and 2 x optical Ethernet over 24 km function, separate SFPs are necessary. These can be ordered as
accessories.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
USART-AH-1LDFO2
USART-AX-2LDFO4
USART-AY-2LDFO5
USART-AW-2LDFO
USART-AJ-1LDFO3
USART-AG-1LDFO
USART-AU-2LDFO
USART-AK-1LDFO
USART-AV-2LDFO
USART-AF-1LDFO
USART-AD-1FO
USART-AE-2FO
USART-AC-2EL
USART-AB-1EL
ETH-BD-2FO1
ANAI-CA-4EL
ARC-CD-3FO
ETH-BB-2FO
ETH-BA-2EL
Plug-In Module
1 x optical serial, bidirectional via 1 ■

common optical fiber, 1550 nm/
1300 nm (Tx/Rx), LC simplex plug, 40
km via 9/125 μm singlemode optical
fiber3
1550 nm (Tx/Rx), 2 x LC simplex plug, 40
fiber4
1300 nm (Tx/Rx), 2 x LC simplex plug, 40
fiber5
8-pin screw-type terminal spring ■
3 x optical (for point sensor) ■
Application
DIGSI 5 protocol ■ ■ ■
IEC 61850-8-1 server ■ ■ ■
You can find more information (whether
GOOSE or MMS reporting) in the
Communication protocols manual,
chapter IEC 61850.
IEC 61850-9-2 Merging Unit ■
IEC 61850-9-2 Process-Bus Client ■
IEC 60870-5-103 ■ ■ ■ ■
IEC 60870-5-104 ■ ■ ■
DNP3 serial ■ ■ ■ ■
DNP3 TCP ■ ■
Modbus TCP ■ ■
Synchrophasor (IEEE C37.118 - PMU) ■ ■ ■
Protection interface (Sync. HDLC) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Protection interface (IEEE C37.94) ■ ■
PROFINET IO ■ ■ ■7
SUP Serial (Slave Unit Protocol) for ■ ■ ■ ■
connecting external temperature- or 20-
mA measuring devices

7 PROFINET IO is available in the ETH-BD-2FO module with S2 redundancy and SOE functionality for V8.30 and higher.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
USART-AH-1LDFO2
USART-AX-2LDFO4
USART-AY-2LDFO5
USART-AW-2LDFO
USART-AJ-1LDFO3
USART-AG-1LDFO
USART-AU-2LDFO
USART-AK-1LDFO
USART-AV-2LDFO
USART-AF-1LDFO
USART-AD-1FO
USART-AE-2FO
USART-AC-2EL
USART-AB-1EL
ETH-BD-2FO1
ANAI-CA-4EL
ARC-CD-3FO
ETH-BB-2FO
ETH-BA-2EL
Plug-In Module
SUP Ethernet (Slave Unit Protocol) for ■ ■

connecting external temperature or 20-
mA measuring devices
Diagnosis: Ethernet module homepage ■ ■ ■
(http)
Measuring transducer, 4 inputs, DC ■
±20 mA
Arc protection ■
Additional Ethernet protocols and services
DHCP, DCP (automatic IP configuration) ■ ■ ■
Line Mode ■ ■ ■
PRP (Ethernet ring redundancy) ■ ■ ■
HSR (Ethernet ring redundancy)8 ■ ■ ■
RSTP (Ethernet ring redundancy) ■ ■ ■
SNTP (time synchronization via Ethernet) ■ ■ ■
SNMP V3 (network management ■ ■ ■
protocol) 9
IEEE 1588v2 (PTP protocol via Ethernet – ■ ■

ms accuracy)
IEEE 1588v2 (PTP protocol via Ethernet – ■
µs accuracy)10
IEEE 802.1q (VLAN) ■
NOTE
i The USART and ETH plug-in module types can be used in slots E and F in the base module as well as in slots
N and P in the CB202 expansion module. They are not intended for use in slot M in the CB202 expansion
module.
The plug-in modules of types ANAI and ARC can be used in both slots in the base module (ports E and F), as
well as in all slots in the expansion module CB202 (ports M, N, and P).
4.2.3 Serial Modules for Short Distances
4.2.3.1 Special Features of Serial Electrical Modules

The serial electrical modules are equipped with RJ45 connections. These are not Ethernet connections. The
serial signals of the RS485 interface are routed to the RJ45 connections (see following figure).

8 HSR is available in the ETH-BD-2FO module for V8.30 and higher, without supporting the IEEE 1588v2 transparent clock.
9 Available for V8.30 and higher
10 SFP accuracy is 1 ms with optional RJ45

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
[dwrj45pb-030211-01.tif, 1, en_US]
Figure 4-4 RJ45 Terminals for the Serial Signals of the RS485 Interface
Cabling Examples of Devices with Serial Electrical Modules

Serial electrical RS485 connections of devices in the SIPROTEC 5 series can be cabled with low-cost Ethernet
patch cables. Special bus cables and adaptors are not needed. Pay attention to the following note if you
include devices from the SIPROTEC 4 series in the connection.
NOTE
i The RS485 interface in devices of the SIPROTEC 4 series is a D-Sub 9 connection with a connected terminal
resistor.
If you connect devices from the SIPROTEC 5 series with devices from the SIPROTEC 4 series, then use a Y
adaptor with the order designation 7XV5103-2BA00. Complete the connection on the last device with a
terminal resistor. For the SIPROTEC 5 device, use a terminal resistor with the order designation RS485-
Terminator 7XV5103-5BA00.
[dwserma1-030211-04.tif, 1, en_US]
Figure 4-5 Communication with a Single Master Using an RS485 Bus
The preceding figure shows the cabling using the new RJ45 sockets in a simplified format. The serial RS485
bus can be extended by simply connecting Ethernet patch cables from device to device.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
[dwserma2-030211-05.tif, 1, en_US]
Figure 4-6 Redundant Communication with 2 Masters Using RS485 Bus (for Example, Redundant
IEC 60870-5-103 Protocol)
The preceding figure shows the use of both connections on one module for connecting the devices to 2 inde-
pendent masters following the same principle as with a single master.
Reorders
When reordering serial communication modules, specify the product code for the physical version of the
module. The order configurator (IPC configurator) shows you which applications are capable of running on the
module:
• Serial
• 1-channel or 2-channel
• Electrical or optical
4.2.3.2 USART-AB-1EL
Description Serial asynchronous communication module with one electrical inter-

face
Product code P1Z79
Figure
Connector type 2 x RJ45

Baud rate 1.2 kbit/s to 115.2 kbit/s
Protocol IEC 60870-5-103
DNP3
SUP serial

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
4.2.3.3 USART-AC-2EL
Description Serial asynchronous communication module with 2 independent elec-

trical interfaces
Product code P1Z437
Figure

Baud rate 1.2 kbit/s to 115.2 kbit/s
For 1 or 2 protocols or applications IEC 60870-5-103
(1 application per connection) DNP3
SUP serial
4.2.3.4 USART-AD-1FO
Description Serial asynchronous or synchronous communication module with

1 independent optical interface
Product code P1Z62
Figure
Connector type 2 x ST
Wavelength λ = 820 nm
Baud rate Asynchronous: 1.2 kbit/s to 115.2 kbit/s
Synchronous: 64 kbit/s to 2 Mbit/s
For 1 protocol or application IEC 60870-5-103
DNP3
SUP serial
Protection-interface communication
Max. distance 2 km when using an optical fiber 62.5 μm/125 μm
Transmitter Power Minimum Typical Maximum

50 μm/125 μm, NA11 = 0.2 -19.8 dBm -15.8 dBm -12.8 dBm
62.5 μm/125 μm, NA11 = 0.275 -16.0 dBm -12.0 dBm -9.0 dBm
11 Numerical Aperture (NA = sin θ [launch angle])

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Receiver sensitivity Maximum +1 dBm

Minimum -32 dBm
Optical budget Minimum 4.2 dB for 50 μm/125 μm, NA11 = 0.2
Minimum 8.0 dB for 62.5 μm/125 μm, NA11 = 0.275
Laser class 1 as per EN 60825-1/-2 With the use of 62.5 μm/125 μm and 50 μm/125 μm optical fibers
4.2.3.5 USART-AE-2FO
Description Serial asynchronous or synchronous communication module with

2 independent optical interfaces
Product code P1Z48
Figure
Connector type 4 x ST
Baud rate Asynchronous: both connections 1.2 kbit/s to 115.2 kbit/s
Synchronous: both connections 64 kbit/s to 2 Mbit/s
Asynchronous/Synchronous: 1 connection 1.2 kbit/s to 115.2 kbit/s and
1 connection 64 kbit/s to 2 Mbit/s
For 1 or 2 protocols or applications IEC 60870-5-103
(1 application per optical connec- DNP3
tion) SUP serial
Protection-interface communication
Max. distance 2 km when using an optical fiber 62.5 μm/125 μm

Receiver sensitivity Maximum +1 dBm

Minimum -32 dBm
4.2.4 Serial Modules for Long Distances
4.2.4.1 Application
The optical protection-interface modules are used for long distances over multimode or singlemode optical
fibers. In the case of the protection interface, they serve the purpose of point-to-point transmission between 2

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
devices. One possible application is the transmission of differential protection data. For example, if you wish
to transmit only binary data and measured values, you can equip all SIPROTEC devices with these protection
interfaces.
The attainable distance in multimode optical fibers is limited by 2 factors.
• Bandwidth length product

Typical for 62.5 μm/125 μm optical fibers: 400 MHz x km to 800 MHz x km
Typical for 50 μm/125 μm optical fibers: 400 MHz x km to 1200 MHz x km
• Fiber attenuation
The typical attenuation of a 62.5 μm/125 μm optical fiber is from 0.9 dB/km to 1 dB/km for light with the
wavelength λ = 1300 nm. 1.5 dB/km are added for splices, aging and as a reserve. An attenuation of
2.5 dB/km is used for calculation of the distance.
4.2.4.2 USART-AF-1LDFO
Description Protection-interface module for synchronous operation with an optical

interface
Product code P1Z758
Figure
Connector type 1 x duplex LC

Baud rate 2 Mbit/s for the protection-interface communication
Protocol Protection-interface communication
Max. distance 24 km for singlemode optical fibers or
4 km with multimode optical fiber
Distance 4 km
Minimum Maximum
Transmitter power coupled in -15.0 dBmavg -8.0 dBmavg
multimode optical fiber
Receiver sensitivity -8.0 dBmavg -31.0 dBmavg
Optical budget 16.0 dB –
Distance 24 km
Laser class 1 as per EN 60825-1/-2 With the use of 9 μm/125 μm optical fibers
Minimum Maximum
singlemode optical fiber

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
4.2.4.3 USART-AG-1LDFO

interface
Product code P1Z468
Figure

Max. line length 60 km for singlemode optical fibers or
Distance 8 km
Minimum Maximum
Transmitter power coupled in -5.0 dBmavg 0 dBmavg
Receiver sensitivity 0 dBmavg -34.0 dBmavg
Distance 60 km
Minimum Maximum
Transmitter power coupled in -5.0 dBmavg 0 dBmavg
4.2.4.4 USART-AH-1LDFO
NOTE
i Use the protection-interface module USART-AH-1LDFO paired with USART-AJ-1LDFO or USART-AY-2LDFO

only.

interface
In particular, a bidirectional data exchange through a single optical fiber
is possible with the USART-AJ-1LDFO module.
Product code P1Z765

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Figure
Connector type 1 x simplex LC

Max. line length 40 km for singlemode optical fibers
Distance 40 km
Minimum Maximum
Transmitter power coupled in the -8.0 dBmavg -3.0 dBmavg
4.2.4.5 USART-AJ-1LDFO
NOTE
i Use the protection-interface module USART-AJ-1LDFO paired with USART-AH-1LDFO or USART-AX-2LDFO

only.
Description Protection-interface module for synchronous operation with 1 optical

interface
is possible with the USART-AH-1LDFO module.
Product code P1Z1007
Figure


C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Distance 40 km
Minimum Maximum
singlemode optical fibers
4.2.4.6 USART-AK-1LDFO

interface
Product code P1Z888
Figure

Distance 100 km
Minimum Maximum
[dwdaempf-030211-01.tif, 2, en_US]
Figure 4-7 Optical Remote Connection with Attenuators
NOTE
i If you use the protection-interface module USART-AK-1LDFO for distances under 30 km, then connect
2 attenuators 7XV5107-0AA00. To continue using the duplex LC plugs, attach both attenuators to one end
of the remote connection (see Figure 4-7).

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
4.2.4.7 USART-AW-2LDFO
Description Protection-interface module for synchronous operation with 2 optical

interfaces
Product code P1Z772
Figure

Distance 4 km
Minimum Maximum
Distance 24 km
Minimum Maximum
4.2.4.8 USART-AU-2LDFO
Description Protection-interface module for synchronous or asynchronous operation

with 2 optical interfaces
Product code P1Z239
Figure

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules

Distance 8 km
Minimum Maximum
Transmitter power coupled in -5.0 dBmavg 0.0 dBmavg
Distance 60 km
Minimum Maximum
Transmitter power coupled in -5.0 dBmavg 0.0 dBmavg
4.2.4.9 USART-AX-2LDFO
NOTE
i Use the protection-interface module USART-AX-2LDFO paired with USART-AY-2LDFO or USART-AJ-1LDFO

only.

is possible with the USART-AY-2LDFO module.
Product code P1Z802
Figure


C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Distance 40 km
Minimum Maximum
4.2.4.10 USART-AY-2LDFO
NOTE
i Use the protection-interface module USART-AY-2LDFO paired with USART-AX-2LDFO or USART-AH-1LDFO

only.

is possible with the USART-AX-2LDFO module.
Product code P1Z789
Figure

Distance 40 km
Minimum Maximum
4.2.4.11 USART-AV-2LDFO

Product code P1Z741

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Figure

Distance 100 km
Minimum Maximum
NOTE
i If you use the protection-interface module USART-AV-2LDFO for distances under 30 km, then connect
2 attenuators 7XV5107-0AA00. To continue using the duplex LC plugs, attach both attenuators to one end
of the remote connection (see Figure 4-7).
4.2.5 Ethernet Modules
4.2.5.1 Operation of Ethernet Modules

The Ethernet modules of the SIPROTEC 5 series can be operated optionally with or without integrated switch
function. This applies for the electrical as well as the optical module. This function can be selected via the
parameterization. It is not necessary to make any indication in the order. The optical Ethernet modules are
compatible with the EN100 modules of the SIPROTEC 4 series. If the RSTP protocol or the HSR protocol is
active, the optical modules of the SIPROTEC 4 series and the SIPROTEC 5 series can be operated in a ring.
When using SIPROTEC 4 devices with module firmware ≤ V4.06 and SIPROTEC 5 devices, the maximum allow-
able number of participants is 30 devices. When using SIPROTEC 4 devices with module firmware ≥ V4.07 and
SIPROTEC 5 devices, the maximum allowable number of participants is 40 devices. When using SIPROTEC 5
devices, the maximum allowable number of participants is 40 devices.
Figure 4-8 shows operation of the Ethernet modules with integrated switch function. All devices of a station
are shown which are connected to one another by means of optical fibers. The devices form optical rings. In
addition, 2 switches are used on the substation controller for the SICAM PAS. The 2 switches take the require-
ments for the redundancy into account.
Additional participants with electrical interfaces can also be connected to the SICAM PAS (for example, the
DIGSI 5 control PC). An external switch is sufficient. Optical communication modules are primarily used for this
topology, as there can be substantial distances between the devices.
If the Ethernet modules are installed in expansion modules with a CB202 PCB assembly, the power supply can
be provided with an independent battery. The integrated switch can maintain its function when the device is
switched off. The data are transmitted in optical and electric rings. This prevents opening of the ring. The ring
continues to operate when 1 or more devices are switched off.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
[dweth1sw-030211-01.tif, 2, en_US]
Figure 4-8 Operation of Ethernet Modules with an Integrated Switch Function
Figure 4-9 shows the operating mode without integrated switch function. Optionally, the 2nd connection can
be connected to the 2nd switch. This connection is shown with a dashed line in Figure 4-9. The IP communica-
tion is established using the 1st connection here. If this connection fails, the system changes over to the 2nd
connection within a few milliseconds. The IP connection is retained practically without interruption using the
2nd switch. This hot-standby connection redundancy increases the availability in such configurations, as
shown in the following figure. The information on failure of the protection connection is transmitted to the
substation automation technology.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
[dwethsw3-090713-01.tif, 2, en_US]
Figure 4-9 Operation of Ethernet Modules Without Integrated Switch Function with Single or Redundant
Connection to the Switch
4.2.5.2 ETH-BA-2EL
Description Communication module for the transmission of Ethernet protocols via

2 electrical interfaces
Product code P1Z55
Figure

Baud rate 100 Mbit/s
Protocol DIGSI 5 protocol (secure Web service protocol)
IEC 61850 (MMS and GOOSE)
DNP3
Modbus
IEC 60870-5-104
PROFINET IO
Synchrophasor protocol (IEEE C37.118 - PMU)
You can switch other network services like SNMP, RSTP, PRP, HSR, SNTP,
and SUP Ethernet on and off.
Max. line length 20 m with Ethernet patch cable CAT 6 S/FTP, F/FTP, or SF/FTP
Interface design Corresponds to IEEE 802.3, 100Base-TX

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
4.2.5.3 ETH-BB-2FO

2 optical interfaces
Product code P1Z390
Figure

DNP3
Modbus TCP
IEC 60870-5-104
PROFINET IO
Synchrophasor protocol (IEEE C37.118 - PMU)
You can switch other network services like SNMP, RSTP, PRP, HSR, SNTP,
and SUP Ethernet on and off.
Max. line length 2 km for 62.5 µm/125 µm optical fibers

Receiver sensitivity Maximum -12.0 dBm

Minimum -31.0 dBm
Interface design Corresponds to IEEE 802.3, 100Base-FX
4.2.5.4 ETH-BD-2FO

2 optical interfaces, suitable for Process-bus client, Merging Unit, and
ultrafast GOOSE

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Figure

IEC 61850-8-1 (9-2 Client and 9-2 Merging Unit)
IEC 60870-5-104
PROFINET IO
Synchrophasor protocol (IEEE C37.118 – PMU)
You can switch other network services such as HSR, SNMP, RSTP, PRP,
SNTP, and IEEE 1588v2/PTP on and off.
Max. line length 2 km for 62.5 µm/125 µm optical fibers

Receiver sensitivity Maximum -12.0 dBm

Minimum -31.0 dBm
Interface design Corresponds to IEEE 802.3, 100Base-FX
The ETH-BD-2FO module offers the possibility of replacing the SFPs (Small Form-Factor Pluggable) delivered by
default for a communication route of up to 2 km by SFPs that can be ordered separately in order to adapt the
interface to different transmission media and longer routes.
SFP with Optical Interface for 24 km, Single Mode
Description SFP for distances up to 24 km when using singlemode optical fibers

Connector type Duplex LC
Protocol See information for the module ETH-BD-2FO
Max. line length 24 km for 9 µm/125 µm optical fibers
Distance 24 km
Laser class 1 as per EN 60825-1/-2 With the use of 9 µm/125 µm optical fibers

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Transmitter Power Minimum Maximum

Transmitter power coupled in -15 dBm -8 dBm
singlemode optical fibers
Receiver sensitivity -8 dBm -31dBm
Optical budget 16 dB –
SFP with Electrical Interface
Description SFP with RJ45 connector, for Ethernet protocols via an electrical inter-
face
Connector type RJ45
Protocol See information for the module ETH-BD-2FO
Removing SFP Pluggable Transceivers
! CAUTION
Risk of burns due to high temperatures of the SFP pluggable transceivers
Noncompliance with the safety notes may result in medium or light injuries.
² The SFP pluggable transceivers can be disconnected and plugged in while in operation. Siemens
recommends switching off the device.
² Allow the SFP pluggable transceiver to cool as much as possible.
✧ Remove the connecting cables or the dust protection cap that was plugged on in the delivery state from
the SFP pluggable transceiver.
✧ In order to release the interlocking, open the bracket on the SFP pluggable transceiver.
✧ Pull on the bracket in order to pull the SFP pluggable transceiver out of the slot. The removal must be
possible with free movement and without great exertion of force.
✧ Provide the SFP pluggable transceiver with the dust protection cap so that the optics are protected from
contamination.
Mounting SFP Pluggable Transceivers
✧ Check whether the bracket on the SFP pluggable transceiver is closed.

The bracket must be closed.
✧ Insert the pluggable transceiver into the slot until it audibly locks in place.
The SFP is securely fixed in the slot.
NOTE
i Check for secure positioning of the transceiver in the slot and whether it is locked in place in order to avoid
unintentional removal by pulling on the connection line.

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
4.3 Measuring-Transducer Modules
4.3.1 Overview
You can install the measuring-transducer modules in base modules or 1/3 modules (plug-in module positions E
and F) and in expansion modules with a CB202 plug-in module assembly (plug-in module position M, N, or P).
4.3.2 ANAI-CA-4EL
The ports CH1 to CH4 of the measuring-transducer modules are Safety Extra Low Voltage circuits (SELV
circuits). For the connection to the measuring-transducer modules, the following conditions apply:
• SELV circuits may be connected only to SELV circuits.
• Ensure that the cables of SELV circuits are routed separately from the supply circuits.
• Use shielded cables.

Figure
Terminal diagram
Connector type 8-pin terminal spring

Differential current input channels 4
Measuring range DC -24 mA to +24 mA
Error limit 0.5 % of measuring range
Input impedance 140 Ω
Conversion principle Delta-sigma (16 bit)
Permissible potential difference DC 20 V
between channels
Galvanic separation with respect to AC 500 V, DC 700 V
ground/housing

C53000-G5040-C002-K, Edition 11.2020
Plug-In Modules
Permissible overload DC 100 mA continuously

Measured-value repetition 200 ms
4.3.3 ARC-CD-3FO
With the module, you can detect an arc in the air-insulated system part of the switchgear by way of an optical
arc sensor.
Figure
Connector type AVAGO AFBR-4526Z

Number of sensor connections 3 point or line sensors (combinations are possible)
Fiber type Polymer Optical Fiber (POF) 1 mm
Receiver
Maximum -10 dBm ± 2 dBm
Minimum -40 dBm ± 2 dBm
Spectrum 400 nm to 1100 nm
Attenuation In the case of polymer optical fibers, you can expect a path attenuation
of 0.2 dB/m. Additional attenuation comes from the plug and sensor
head.
Optical budget 15 Minimal 25 dB
Analog sampling rate 16 kHz
ADC type 10-bit successive approximation
Transmitter
Type LED
Transmitter power Minimum 0 dBm
Maximum 2 dBm
Numerical aperture 0.5 16
Signal rate connection test 1 pulse per second
Pulse duration connection test 11 μs
NOTE
i Laser class 1 is maintained in compliance with EN 60825-1 and EN 60825-2 when using 1 mm polymer
optical fibers.
15 All values in combination with sensors approved by Siemens.

16 Numerical aperture (NA = sin θ (launch angle))

C53000-G5040-C002-K, Edition 11.2020
5 Working on the Device
5.1 First Steps 180

5.2 Expanding Modular Devices 182
5.3 Plug-In Modules 195
5.4 Arc Sensors for Module: ARC-CD-3FO 200
5.5 Battery 206
5.6 SDHC Memory Card 209
5.7 Installing Current and Voltage Terminals 211

C53000-G5040-C002-K, Edition 11.2020
Working on the Device
5.1 First Steps
5.1 First Steps
5.1.1 Electrical Inspection
Device Protection
! DANGER
Danger when connecting the SIPROTEC 5 device
Noncompliance with the safety notes will result in death, severe injury or considerable material
damage.
² The device must be situated in the operating area for at least 2 hours before you connect it to the
power supply for the first time. This prevents condensed water from forming in the device.
² If the device has been in storage for more than 2 years, connect it to an auxiliary voltage for 1 to
2 days. This will cause the electrolytic capacitors to form on the printed circuit board assemblies again.
² Perform the electrical inspection.
Activating the Battery
NOTE
i The battery is covered by a protective film, which also prevents premature discharge.
The battery compartment is located on the rear of the base module. You do not have to take the battery
out of the battery compartment in order to remove the protective film.
² Pull out the battery compartment including the battery.

² Remove the protective film from the battery by simply pulling on the film tab.
² Push the battery compartment including the battery back in again.
Grounding a Device
The SIPROTEC 5 devices are protection class I equipment must be connected with the system ground prior to
commissioning.
² Ground each module with solid low-impedance system grounding (cross-section ≥ 4.0 mm2
(≥ 0.0062 in2), grounding area ≥ M4, torque: at least 1.2 Nm).
² In order to ensure the electromagnetic compatibility (EMC) of the device, connect the protective
grounding terminals of the modules to each other in series connection. Use the double protective
grounding terminals of the individual modules for this purpose.
² Connect the protective conductor of the protection device (connected modules) to the protective
grounding terminal of the installation (for example control cabinet) with a single connection to the base
module of the protection device.
Connecting a Device
² Connect all cables and lines. Use the connection diagrams in the Hardware Manual and Device Manual.
² Tighten the terminal screws to the prescribed torques (see chapter Tightening Torques for Terminal
Screws, Page 246).

C53000-G5040-C002-K, Edition 11.2020
5.1 First Steps
Grounding an On-Site Operation Panel

² Join several on-site operation panels to one another with firm contact.
Siemens recommends the use of contact washers on painted metal mounting walls. If the mounting wall
is not metallic, place a metal layer, for example a metal sheet, between the mounting wall and the on-
site operation panels. Then connect this sheet to the system grounding.
Safety Notes
! DANGER
Danger during electrical inspection
Noncompliance with the safety notes will result in death, severe injury or considerable material
damage.
² Comply with all given safety notes when carrying out the electrical inspection.
² Please note that hazardous voltages are present when you perform the electrical inspection.
² During the electrical inspection, check that the device becomes ready for operation once it has been
connected to the power supply.
Performing the Electrical Inspection

² Connect the power supply.
² Activate the power supply.
After (initial) activation, there is no Device Configuration File (DCF) in the device and the device is in fall-
back mode. The green and red LEDs light in fallback mode.
² Once you have loaded the DCF file into the SIPROTEC 5 device, the green RUN LED lights continuously
and the device is ready for operation.
² If the device does not assume the normal operating state (process mode), switch off the power supply.
Disconnect the wiring and the grounding.
² Pack this device and return it to the manufacturer, stating the defect. Use transport packaging that meets
the requirements of standard ISO 2248.

C53000-G5040-C002-K, Edition 11.2020
5.2 Expanding Modular Devices
5.2.1 Flush-Mounting Devices
5.2.1.1 Basic Rules for Expansion
NOTE
i Prepare the following tools for the device expansion:
• Phillips screwdriver size PZ1 and PZ2
• Screwdriver DIN 4 x 0.8
• During assembly, use the prescribed torques (see chapter 6.13 Design Data).
Comply with the following basic rules when expanding devices:

² Always fit the base module on the left in the 1st device row.
² Always fit the expansion modules from left to right.
² Always fit the expansion module with the key switches as the 1st module next to the base module.
² Always fit the expansion modules without LEDs last.
² Always install a power-supply module PS203 on the left as the first unit in the 2nd device row.
² Note that the PS203 must always have the same rated voltage as the base module.
² In the 2nd device row, mount only input and output modules without LEDs.
² Always mount the redundant power-supply module PS204 at the very right in the corresponding row
(seen from the front). If a CB202 PCB assembly is used in the row, this CB202 PCB assembly must always
be plugged on the right of the power-supply module PS204 (at the very right). You can find an example
for this in chapter 3.1.4.2 Positioning Specifications.
² Note that the power-supply module PS204 must always have the same rated voltage as the base module.

C53000-G5040-C002-K, Edition 11.2020
[dweinzei-030211-01.tif, 2, --_--]
Figure 5-1 Device Row of a Flush-Mounting Device
5.2.1.2 Expanding 1st Device Row
Preparation
NOTE
i Reordered modules are not contained in the original device configuration. Use DIGSI to perform the corre-
sponding extension in the Hardware and Protocols Editor.
Carry out the steps described in this chapter if you wish to expand an installed device later on with expan-
sion modules.
² Shut down the device.

² Use the screwdriver to carefully bend the left and right spring clips on the rear plate terminals outwards.
² Completely detach the wired current and voltage terminal blocks from the device.
² Remove all communication lines.
² Remove the plastic screw covers.
² Remove the device.
² Expand the cut-out in the control cabinet.
² Then continue with assembly.
Assembling the Devices

² Remove the bus cover from the extreme right-hand module of the device to be expanded.

C53000-G5040-C002-K, Edition 11.2020
² Remove the plastic screw covers from the expansion module.

² Remove the right sealing strips from the base device.
² Place the expansion module on the right next to the device. Insert the 2 hinged angle clips of the expan-
sion module in the cut-outs of the device.
² Slip ring the expansion module in the direction of the device so that the bottom snap-in spring engages.
² Bolt the 2 on-site operation panels of the module to one another through the contact tab.
² Check that the bus connection is screwed on at the extreme right of the expansion module.
Installation and Commissioning

² Reinstall the device.
² Reinstall the plastic screw covers.
² Refasten the terminal blocks and the necessary communication lines.
² Connect the current and voltage blocks of the expansion module.
² Connect any available plug-in modules.
² Use the supplied grounding cable to connect the expansion module with the device and reconnect the
device to service ground.
² Extend the device configuration in DIGSI and load this configuration to the device.
² Resume operation of the device.
5.2.1.3 Expanding Devices with 2nd Device Row
Preparation
NOTE
Carry out the steps described in this chapter if you want to expand an installed device later on with a 2nd
device row.
² Shut down the device in the 1st device row.

² Remove the plastic screw covers.
² Remove the device from the 1st device row.
² Remove the device bus cover from the extreme right-hand expansion module of the device to be
expanded.
² Screw the sealing plate and the adaptor bracket according to Figure 5-4 on the outer right expansion
module of the 1st device row. The sealing plate, adaptor angle, and screws are included with the supply
of the power-supply module PS203.
² Attach the cable holder for the connecting cable of the 2nd device row to the back side of the angle rail.
² Clip the connecting cable into the cable holder.

C53000-G5040-C002-K, Edition 11.2020
NOTE
i Observe the direction of the connecting cable.

Note that the available cable end for the connection of the 2nd device row must be longer than the cable
end for the connection of the 1st device row.
² Insert the cable in the rubber seals, and introduce the seals in the slot of the angle rail (see Figure 5-3)

² Install the angle rail.
² Install the 1st device row above the angle rail.
² Install the 2nd device row below the angle rail.
² Screw the 2 handle moulds of the connecting cable to the 1st and 2nd device row.
NOTE
i Make sure that the handle moulds are not rotated during assembly so as not to damage the contact
surfaces of the plugs.
[dw_2zauba-020414-01, 2, --_--]
Figure 5-2 Expansion with 2nd Device Row
(1) Extreme right expansion module of the 1st device row

(2) Connecting cable
(3) 2nd device row
[dw_schiene-020414-01, 1, --_--]
Figure 5-3 Angle Rail
(1) Angle rail

(2) 2 Rubber seals

C53000-G5040-C002-K, Edition 11.2020
[dw_winkel-020414-01, 1, --_--]
(1) Device bus of the outermost right expansion module of the 1st device row
(2) Sealing plate
(3) Adaptor angle
(4) 2 mounting screws

5.2.2 Surface-Mounted Devices with Integrated On-Site Operation Panel
NOTE
• Always fit the base module on the right in the 1st device row.
• Always fit the expansion modules from right to left.
• Always fit the on-site operation panel of the base module on the left.

C53000-G5040-C002-K, Edition 11.2020
• Always fit the on-site operation panels of the expansion modules from left to right.
• Always fit the on-site operation panel of the expansion module with the key switches in the 1st place
next to the on-site operation panel of the base module.
• Always fit the on-site operation panels without LEDs last.
• Join the on-site operation panels to one another with 2 mounting brackets.
• Always install a power-supply module PS203 on the right as the first unit in the 2nd device row.
• Note that the PS203 must always have the same rated voltage as the base module.
• Always mount the redundant power-supply module PS204 at the very right in the corresponding row
(seen from the front). If a CB202 PCB assembly is used in the row, this CB202 PCB assembly must always
be plugged on the right of the power-supply module PS204 (at the very right). You can find an example
for this in chapter 3.1.4.2 Positioning Specifications.
• Note that the power-supply module PS204 must always have the same rated voltage as the base module.
• In the 2nd device row, you do not need any on-site operation panels, mounting brackets, or distance
frames.
NOTE
i When expanding a device in the 1st device row, order 2 mounting brackets that match the width of the
expanded device.
[dwauize1-040211-01.tif, 2, --_--]
Figure 5-5 Device Row
(1) Distance frame

(2) Mounting bracket
(3) Distance frame on base module rotated by 180o

C53000-G5040-C002-K, Edition 11.2020
Preparation
NOTE
sion modules.

² Detach all on-site operation panels from the distance frames.
² Remove the mounting brackets.
NOTE
i If the device is an expanded device, then detach the 2 mounting brackets. You must replace these
mounting brackets with 2 new mounting brackets that match the width of the device.
² Use a screwdriver to carefully bend the left and right spring clips on the terminals outwards.
² Remove the device completely.
Assembling the On-Site Operation Panel into One Block
[dwaublo1-040211-01.tif, 2, --_--]
Figure 5-6 On-Site Operation Panel Fitted on Mounting Bracket
² Place the 2 mounting brackets intended for expansion in parallel to one another on a flat surface.

C53000-G5040-C002-K, Edition 11.2020
² Bolt the 1st (left-hand) on-site operation panel to the 2 mounting brackets. Do not firmly tighten the
screws.
² Place the 2nd on-site operation panel on the right of the 1st one and screw these panels onto the 2
mounting brackets. Do not firmly tighten the screws. Make sure that the snap-in spring is engaged!
² Bolt the 2 operation panels to one another through the contact tab. Do not firmly tighten the screws.
² Repeat the last 2 steps for the remaining operation panels. Leave all screws loose.

² Remove the distance frame from the expansion module.
² Remove the bus cover from the extreme left-hand module.
² Remove the plastic screw covers from the extreme left-hand module and from the expansion module.
² Place the expansion module on the left next to the device. Insert the 2 hinged angle clips of the expan-
sion module in the cut-outs of the device.
² Swivel the expansion module in the direction of the device so that the bottom snap-in spring engages.
² Bolt the contact tab to the 2 modules.

² Install the distance frame intended for expansion.
² Wire and, if required, fasten the current and voltage terminal blocks.
² Fit the device back onto the wall without fastened on-site operation panels.
² Fasten the connecting cable for the on-site operation panel on the extreme left-hand operation panel of
those on-site operation panels assembled beforehand into a block.
² Place the block of assembled operation panels on the distance frames of the device. In doing so, guide
the connecting cable for the on-site operation panel through the cut-outs of the distance frame to the
terminal of the base module.
² Fasten the connecting cable for the on-site operation panel to the base module.
² Bolt the operation panels to the distance frames and firmly tighten the screws.
² Tighten all loose screws on the contact tabs and on the mounting brackets.
² Reinstall all plastic screw covers.
² Extend the device configuration in DIGSI and load it to the device.
5.2.2.3 Expanding Devices with 2nd Device Row
Preparation
NOTE
sion modules.
² Shut down the device in the 1st device row.

C53000-G5040-C002-K, Edition 11.2020
NOTE
i The next 6 steps are only necessary if the 1st device row is not accessible.
If the left side of the 1st device row is accessible, then the complete device can remain on the wall.
² Detach all on-site operation panels from the distance frames.

² Remove the mounting brackets.
² Completely remove the device from the 1st device row.
² Remove the device bus cover from the extreme left-hand expansion module of the device to be
expanded.
² Bolt the sealing plate and the adaptor bracket according to Figure 5-8 on the outer left expansion module
of the 1st device row. The sealing plate, adaptor bracket, and screws are included with the delivery of the
power-supply module PS203.

² Install the 1st device row.
NOTE
i The distance between the 1st and the 2nd device row must be not more than 80 mm (3.15 in).
² Install the 2nd device row.

² Unscrew the captive screws from the handle mold.
² Install the handle mold.
² Install the screws for the handle mold from the view of the adaptor bracket. Thus, later accessibility is
ensured without having to remove the entire device.

C53000-G5040-C002-K, Edition 11.2020
[dw_2zeauf-020414-01, 1, --_--]
Figure 5-7 Expansion with 2nd Device Row (View of the Installation Level without Showing the On-Site
Operation Panel)
(1) Extreme right expansion module of the 1st device row

(2) Connecting cables
(3) 2nd device row
[dw_winauf-020414-01, 1, --_--]
(1) 2 fastening screws

(2) Adaptor angle
(3) Sealing plate
(4) Device bus of the outermost left expansion module of the 1st device row


C53000-G5040-C002-K, Edition 11.2020
² Extend the device configuration in DIGSI and load it to the device.

5.2.3 Surface-Mounted Devices with Detached On-Site Operation Panel
NOTE
• Always fit the base module on the right in the 1st device row.
• Always fit the expansion modules from right to left.
• Always fit the on-site operation panel of the base module on the left.
• Always fit the on-site operation panels of the expansion modules from left to right.
• Always install a power-supply module PS203 on the right as the first unit in the 2nd device row.
• Note that the PS203 must always have the same rated voltage as the base module.
• Always mount the redundant PS204 power-supply module at the position at the very left in the corre-
sponding row (seen from the front). If a CB202 PCB assembly is used in the row, this CB202 PCB assembly
must always be plugged on the left of the power-supply module PS204 (at the very left). You can find an
example in chapter 3.1.4.2 Positioning Specifications.
• Note that the power-supply module PS204 must always have the same rated voltage as the base module.
• The distance between the device and the on-site operation panel is limited to not more than 5 m
(196.85 in) by the length of the connecting cable.
[dwauizei-040211-01.tif, 1, --_--]
Figure 5-9 Device Row

C53000-G5040-C002-K, Edition 11.2020
[dwabosop-040211-01.vsd, 2, en_US]
Figure 5-10 Detached On-Site Operation Panel
Preparation
NOTE
sion modules.

² Use a screwdriver to carefully bend the left and right spring clips outwards.
² If you want to expand the device, then detach it completely.
² If you want to expand the on-site operation panel, then remove the on-site operation panel from the
installation space.
NOTE
i The device and the on-site operation panel can be expand independently of one another. Therefore, you
need only detach those components that are to be expanded.
Installing the Devices (with View to the Installation Plane)

² Remove the bus cover from the extreme left-hand module of the device to be expanded.
² Remove the plastic screw covers from the extreme right-hand module and from the expansion module.
² Place the expansion module on the left next to the device. Insert the 2 hinged angle clips of the expan-
sion module in the cut-out of the device.
² Swivel the expansion module in the direction of the device so that the bottom snap-in spring engages.

C53000-G5040-C002-K, Edition 11.2020
² Bolt the on-site operation panels of the 2 modules to one another through the contact tab.
² Check that the bus connection is screwed on at the extreme left of the expansion module.
Assembly and Commissioning

² Fit the device back onto the wall.
² Expand the on-site operation panel with the on-site operation panel of the expansion modules. Make
sure that the bus connection is plugged in reliably and that the snap-in springs have engaged.
² Bolt the on-site operation panels to one another through the contact tab.
² Check that the bus connection on the expansion module on the extreme right is covered.
² Connect all communication lines again.
Expanding Devices with the 2nd Device Row

² When expanding a surface-mounted device with a 2nd device row, follow the instructions in chapter
5.2.2.3 Expanding Devices with 2nd Device Row.

C53000-G5040-C002-K, Edition 11.2020
5.3 Plug-In Modules
5.3 Plug-In Modules
5.3.1 Fasteners
The fasteners of the plug-in modules are shown in the following figure regarding the example of an installed
module and an empty, covered slot.
[le_fxing_elements, 1, --_--]
Figure 5-11 Fasteners
(1) EMC spring contact

(2) Fastening screw
(3) Cut-out for prying out the modules
(4) Plug-in module
(5) Fastening screw
(6) Cover plate
5.3.2 Installation
NOTE
Preparing Installation
! DANGER
Danger due to live voltage when installing the plug-in modules.
Noncompliance with the safety notes will result in death or severe injuries.
² Install plug-in modules on the electrically deactivated device only.

C53000-G5040-C002-K, Edition 11.2020
5.3 Plug-In Modules
! CAUTION
Exercise caution with laser beams of the optical plug-in modules.
Noncompliance with the safety notes can result in medium-severe or slight injuries.
² Do not look directly into the optical fiber terminals of the active optical plug-in modules, not even with
optical devices. The laser beams can damage the eyes.
² De-energize the device.
NOTE
i When using optical communication modules, Laser class 1 is maintained in compliance with EN 60825-1
and EN 60825-2 when using optical fibers ≤ 62.5 μm/125 μm.
When using the ARC-CD-3FO module, Laser class 1 is maintained in compliance with EN 60825-1 and
EN 60825-2 when using 1 mm plastic optical fibers.
² In the case of a surface-mounted device with integrated on-site operation panel, remove the entire on-
site operation panel.
² Undo the fastening screw and remove the cover plate from the plug-in module position.
Installing the Plug-In Module

² Push in the plug-in module on the inner guide as far as it will go.
² Ensure that the EMC contact spring is seated correctly.
² Bolt down the plug-in module on the assembly frame to a torque of 0.4 Nm.
² Connect the lines to the terminals.
² Then check for secure attachment of the plugs.
² If necessary, fit the on-site operation panel again.
Completing Installation
5.3.3 Removing
Accessories
NOTE
i Seal an unused plug-in module position with a cover plate.
² Order the module cover plate set of parts to cover the unused plug-in module position.

C53000-G5040-C002-K, Edition 11.2020
5.3 Plug-In Modules
Preparing Removal
! DANGER
Risk of live voltage when removing the plug-in modules.
Noncompliance with the safety notes will result death or severe injuries.
² Remove plug-in modules on the electrically deactivated device only.
! CAUTION
NOTE
i Laser class 1 is adhered to in compliance with EN 60825-1 and EN 60825-2, in the case of ≤ 62.5 μm/
125 μm optical fibers.
² In the case of a surface mounting device with integrated on-site operation panel, remove the on-site
operation panel before the base module.
Removing the Plug-In Module

² Remove all connecting lines.
² Undo the fastening screw with which the plug-in module is fixed on the device.
² Insert a screwdriver (DIN 4 x 0.8) in the cut-out underneath the oblong hole.
² Carefully pull out the plug-in module.
Fastening the Cover Plate

² Fasten the cover plate with the fixing screw to a torque of 0.4 Nm. The fixing screw is included in the set
of parts.
Completing Removal
² In the case of a surface mounting device with integrated local operation panel, fit the on-site operation
panel of the base module again.

C53000-G5040-C002-K, Edition 11.2020
5.3 Plug-In Modules
5.3.4 Replacement
Preparing for Replacement
! DANGER
Danger due to live voltage when replacing the plug-in modules.
Noncompliance with the safety notes will result in death or severe injuries.
² Install plug-in modules on the electrically deactivated device only.
! CAUTION
NOTE
i Laser class 1 is adhered to in compliance with EN 60825-1 and EN 60825-2, in the case of ≤ 62.5 μm/
125 μm optical fibers.
When using the ARC-CD-3FO module, Laser class 1 is maintained in compliance with EN 60825-1 and
EN 60825-2 when using 1-mm plastic optical fibers.
² In the case of a surface-mounted device with integrated on-site operation panel, remove the on-site oper-
ation panel before the base module.
² Undo the fastening screw with which the plug-in module is fixed on the device.
² Insert a screwdriver (DIN 4 x 0.8) in the cut-out underneath the elongated hole in the assembly frame
and disengage the plug-in module.
² Carefully pull out the plug-in module.
Fastening the Plug-In Module

² Push in the new plug-in module on the inner guide of the plug-in module position until it moves no
further.
² Bolt down the plug-in module on the assembly frame to a torque of 0.4 Nm.
² Connect the lines to the terminals.
² Then check for secure attachment of the connectors.
² If necessary, fit the on-site operation panel again.
Completing Replacement
² Place the device is service again and perform a firmware update of the communication modules.

C53000-G5040-C002-K, Edition 11.2020
5.3 Plug-In Modules
NOTE
i If you have not cabled the optical fiber plug-in modules, then seal the terminals with protective covers. This
prevents soiling of the terminals.

C53000-G5040-C002-K, Edition 11.2020
5.4 Arc Sensors for Module: ARC-CD-3FO
5.4.1 Point Sensor
5.4.1.1 Description
The point sensor detects arcs in the control cabinets of the air-insulated system part.
[dwsensap-210314-01, 2, en_US]
Figure 5-12 Point Sensor for the Arc-Protection Module: ARC-CD-3FO
(1) Optically active zone

(2) Sensor head
(3) Supply line
(4) Plug to the arc-protection module: ARC-CD-3FO
(5) Expansion rivet, 4x7
(6) Screw, M4

C53000-G5040-C002-K, Edition 11.2020
[dw_point_sensor_dimensions, 1, en_US]
Figure 5-13 Dimensional Drawing of the Point Sensor
The sensitivity of the point sensors with line lengths up to 4 m typically begins at 10 kLux.
5.4.1.2 Installation
The point sensors are mounted in the different compartments of a control cabinet, see the following figure.
The point sensor detects light in an angle of ± 60°.
[dw_position_sensor, 2, en_US]
Figure 5-14 Mounting Position of the Optical Arc Sensors in the Control Cabinet

C53000-G5040-C002-K, Edition 11.2020
NOTE
i Install the arc sensors in the control cabinet in such a way that the relevant sections are not hidden behind
other system components!
! CAUTION
² Do not look directly into the fiber-optic terminals of the active optical plug-in modules, not even with
NOTE
optical fibers.
² You need 1 hole in the control cabinet for fastening.
Mounting the Point Sensor

² With a wall thickness of 1.5 mm to 2.5 mm, fasten the point sensor using an expansion rivet. This expan-
sion rivet is included in the scope of delivery.
Hole diameter = 4.1 mm to 4.2 mm
² Insert the expansion rivet through the hole in the point sensor and through the hole in the wall. Press the
head of the expansion rivet firmly into the base body.
² As an alternative, you can also fasten the point sensor using a screw (M4). Tighten the screw with a
torque of 0.2 Nm.
² Siemens recommends fastening the line to the wall below the point sensor. The line must not be bent or
stressed in any other way.
R = 50 mm (minimum bending radius)
Maximum continuous tensile force = 1 N
NOTE
i Order the point sensor with a suitable line length. If the line is too long, it must not be shortened! It must
be rolled up with a minimum diameter of 0.3 m because of the optical loss.
Obey the general recommendations of the manufacturers of optical lines.
² Remove the dust caps from the plug and connect the line to the plug-in module.
NOTE
i The contact surfaces of the plug must be clean.
² Then check for secure attachment of the plug.

C53000-G5040-C002-K, Edition 11.2020
NOTE
i In order to warrant safe functioning, the affected sensor must be substituted after detection of an arc.
NOTE
i Hereby, Siemens declares that until now, UL has neither investigated whether the device can detect an arc-
protection fault, neither if in case of an arc-protection fault, the safety of personnel and system is guaran-
teed.
5.4.2 Line Sensor
5.4.2.1 Description
The line sensor detects arcs in the control cabinets of the air-insulated system part.
[dw_line_sensor_mounting, 1, en_US]
Figure 5-15 Line Sensor for the Arc-Protection Module ARC-CD-3FO
5.4.2.2 Installation
Depending on the application, the line sensor can be, for example, laid along the busbar. Additional point
sensors are installed in order to identify the arcs in the circuit-breaker compartment and in the cable connec-
tion compartment.

C53000-G5040-C002-K, Edition 11.2020
Depending on the possibilities of implementing this in the control cabinet, the line sensor can also be passed
through the circuit-breaker compartment and the cable connection compartment of the feeders in addition to
the busbar compartment.
[dw_Liniensensor, 1, en_US]
Figure 5-16 Laying a Line Sensor Along the Busbar
NOTE
i Install the arc sensors in the control cabinet in such a way that the relevant sections are not hidden behind
other system components!
! CAUTION
² Do not look directly into the fiber-optic terminals of the active optical plug-in modules, not even with
NOTE
optical fibers.
² You need 2 holes (10.0 mm in diameter) in the control cabinet for fastening. Siemens recommends a
distance of approx. 10 cm.

C53000-G5040-C002-K, Edition 11.2020
Mounting the Line Sensor

² Fasten both busbar-coupler pieces in both the holes in the control-cabinet wall.
The busbar-coupler pieces (incl. nut and lock washer) are included in the scope of delivery for the sensor.
² Connect one end of the line sensor to a busbar-coupler piece and route the sensor fiber along the section
to be protected, for example, the busbar.
² Make sure that the piece of fiber exposed to the arc has a minimum size of 0.5 m and that the distance
from the potential arc source is a maximum of 0.25 m.
If these boundary conditions cannot be satisfied, please contact our Customer Support for further ques-
tions.
² Fasten the sensor fiber, or example, with cable fasteners.
Ensure that the fiber is not damaged or broken when fastening.
² The sensor fiber is non-conductive. However, ensure that the sensor fiber is laid in such way as to avoid
contact with hot or energized parts.
² During installation, make sure that the sensor and the line are not damaged by sharp edges.
² Sensor areas that should not react to light can be covered up.
² Pass the sensor fiber back again and fasten it with the 2nd busbar-coupler piece.
² The line must not be bent or stressed in any other way.
R = 50 mm (minimum bending radius)
Maximum continuous tensile force = 1 N
² Fasten the supply line with the busbar-coupler piece to the side of the protection device.
² Remove the dust caps from the plug and connect the supply line to the plug-in module.
NOTE
i Order the line sensor and the supply line with a suitable line length. If the line is too long, it must not be
shortened! It must be rolled up with a minimum diameter of 0.3 m because of the optical loss.
Obey the general recommendations of the manufacturers of optical lines.
NOTE
i The contact surfaces of the plug must be clean.
NOTE
i In order to warrant safe functioning, the affected sensor must be substituted after detection of an arc.
NOTE
i Hereby, Siemens declares that until now, UL has neither investigated whether the device can detect an arc-
protection fault, neither if in case of an arc-protection fault, the safety of personnel and system is guaran-
teed.

C53000-G5040-C002-K, Edition 11.2020
5.5 Battery
5.5 Battery
5.5.1 Description
The battery lies in an externally accessible battery compartment. The battery compartment is located on the
rear of the base module. You need not open the device when replacing the battery.
If the auxiliary voltage fails, the battery ensures continued operation of the internal clock and storage of
certain data (statistical values, values of thermal models) for at least 6 months. Parameterization, logs, and
fault records are always stored in a fail-safe way in a non-volatile memory.
The device cyclically checks the charge of the battery. The Battery fault indication is issued if the actual
voltage falls below the minimum.
[dwbatpos-040211-01.tif, 2, --_--]
Figure 5-17 Position of the Battery Compartment in the Modular Device

(2) Battery
[dwbatpo1-240613-01.tif, 2, --_--]
Figure 5-18 Position of the Battery Compartment in the Non-Modular Device (7xx81, 7xx82)

(2) Battery

C53000-G5040-C002-K, Edition 11.2020
5.5 Battery
5.5.2 Replacing the Battery
Safety Notes
NOTICE
Exercise caution when replacing the battery.
Noncompliance with the specified measures can result in material damage.
² Replace the battery only with the type specified in the Technical Data.
NOTICE
Exercise caution when disposing of the battery. The battery contains lithium. Lithium batteries are subject
to the statutory regulations governing the disposal of batteries.
Noncompliance with the specified measures can result in material damage.
² Dispose of the battery in compliance with national and international regulations. Hand in the battery
at an approved collection point, or dispose of it in the collection bins provided for the purpose.
Error Message on the Device

The Battery fault message is displayed on the device.
² Replace the battery.
Replacing the Battery

² Pull out the battery compartment.
² Remove the battery.
² Place the new battery in the battery compartment so that the positive pole points upwards.
² Push the battery compartment back in again.
² Check whether the Battery fault indication is displayed.
² The Battery fault indication is reset within 24 hours or after switching the device on and off again.
You have replaced the battery successfully if the message is no longer displayed.
NOTE
i If you replace the battery without a power supply connected or if you disconnect the device from the
power supply when changing the battery, all battery-backed data will be lost.
5.5.3 Environmental Protection Hints
Disposal of Old Equipment and Batteries (Applicable only for European Union and Countries with a Recycling
System)
The disposal of our products and possible recycling of their components after decommissioning has to be
carried out by an accredited recycling company, or the products/components must be taken to applicable
collection points. Such disposal activities must comply with all local laws, guidelines and environmental speci-
fications of the country in which the disposal is done. For the European Union the sustainable disposal of elec-
tronic scrap is defined in the respective regulation for "waste electrical and electronic equipment" (WEEE).

C53000-G5040-C002-K, Edition 11.2020
5.5 Battery
The crossed-out wheelie bin on the products, packaging and/or accompanying documents means
that used electrical and electronic products and batteries must not be mixed with normal house-
hold waste.
According to national legislation, penalties may be charged for incorrect disposal of such
waste.
By disposing of these products correctly you will help to save valuable resources and prevent any potential
negative effects on human health and the environment.
NOTE
i Our products and batteries must not be disposed of as household waste. For disposing batteries it is neces-
sary to observe the local national/international directives.
Disposal of Mobile Storage Devices (e.g. USB Sticks and Memory Cards)
When disposing of/transferring mobile storage devices, using the format or delete functions only changes the
file management information and does not completely delete the data from your mobile storage device. When
disposing of or transferring a mobile storage device, Siemens strongly recommends physically destroying it or
completely deleting data from the mobile storage device by using a commercially available computer data
erasing software.
REACH/RoHS Declaration
You can find our current REACH/RoHS declarations at:
https://www.siemens.com/global/en/home/products/energy/ecotransparency/ecotransparency-down-
loads.html
NOTE
i You can find more information about activities and programs to protect the climate at the EcoTransparency
website:
https://www.siemens.com/global/en/home/products/energy/ecotransparency.html

C53000-G5040-C002-K, Edition 11.2020
5.6 SDHC Memory Card

The SDHC memory card (Secure Digital High Capacity) is used to store records from the 7KE85 fault recorder.
[dw_SDHC, 1, --_--]
Figure 5-19 SDHC Memory Card
NOTE
i Reading the data of the SDHC memory card with a PC is not intended.
Avoid too frequent insertion cycles!
NOTE
i Use only the original SDHC memory card (ACCESAR) approved by Siemens for the 7KE85 fault recorder.
Replacing the SDHC Memory Card

² Remove the sealing cap.
² Unlock the card by pressing the turquoise eject lever.
[le_Remove_cap_and_SDHC, 1, --_--]
Figure 5-20 Removing the Sealing Cap and SDHC Memory Card

C53000-G5040-C002-K, Edition 11.2020
(1) Push the holder, push the sealing cap to the back and remove it
(2) Unlock the eject lever
(3) Remove the SDHC memory card
² Unpack the new SDHC memory card.

Do not touch the contacts of the SDHC memory card with your fingers.
² Insert the new SDHC memory card.
When inserting, make sure that the SDHC memory card is properly aligned: The side with the contacts
must be facing up, the side with the sticker facing down.
[dw_insert_SDHC, 1, --_--]
Figure 5-21 Inserting the SDHC Memory Card into the Device
! CAUTION
Exercise caution when removing the SDHC memory card from a defective device.
If you want to remove the SDHC memory card from a defective device and to insert the card into another
healthy device and if the data must be kept, note the following:
Noncompliance with the specified measures can result in loss of data.
² To avoid a reformatting of the SDHC memory card, you must first import the parameters of the defec-
tive device to another device.
² You can insert the SDHC memory card in the other device and use it only then.
² The recordings on the SDHC memory card from the defective device can still be read in the other
device.
² Insert the sealing cap back again.


C53000-G5040-C002-K, Edition 11.2020
5.7 Installing Current and Voltage Terminals
5.7.1 Description
[dwklepos-030211-01.tif, 1, --_--]
Figure 5-22 Current and Voltage Terminals with Spring Clips
(1) Current-terminal block

(2) Voltage-terminal block
(3) Spring clips
The spring clips fix the terminal block in place.
[sc_klepos-020414-01, 1, --_--]
Figure 5-23 Voltage Terminal with Screw Connection
[dw_terminal position IO111, 1, --_--]
Figure 5-24 Voltage Terminal with Screw Connection – IO111
Current-Terminal Block of the Modular Devices

The following transformers can optionally be installed in a current-terminal block for modular devices:
• 4 protection-class current transformers
• 3 protection-class current transformers and 1 instrument transformer
• 4 instrument transformers
Protection-class current transformers on modular devices are transformers with a rated current of 1 A or 5 A
and a device-dependent measuring range of 20 x rated current or 100 x rated current.

C53000-G5040-C002-K, Edition 11.2020
NOTE
i You can read the type of the current transformer used on the side of the terminal block, for example 3xI
1xIE. The reference number is located on the connector interface and can only be read when removed.
• C73334A 1A1*7 * = 4 protection-class current transformers
• C73334A 1A1*8 * = 3 protection-class current transformers and 1 instrument transformer
• C73334A 1A1*9 * = 4 instrument transformers
Current-Terminal Block for Non-Modular Devices (7xx81, 7xx82)

The following transformers can be installed optionally in a current-terminal block for non-modular devices:
• 4 protection-class current transformers
• 3 protection-class current transformers and 1 instrument transformer

Protection-class current transformers on non-modular devices are transformers with a rated current of 1 A or
5 A and a measuring range of 50 x rated current.
Instrument transformers are transformers with a rated current of 1 A or 5 A and a measuring range of
1.6 x rated current. Instrument transformers are also referred to as sensitive protection-class current trans-
formers or sensitive ground-current transformers.
NOTE
i You can read the type of the current transformer used on the side of the terminal block, for example 3xI
1xIE. The reference number is located on the connector interface and can only be read when removed.
• C73334A 1A185 * = 4 protection-class current transformers
• C73334A 1A186 * = 3 protection-class current transformers and 1 instrument transformer
Use the cross connector for voltage terminals shown on the right in the figure below for grouping binary
inputs and relay outputs.
[dwquerve-030211-01.tif, 1, --_--]
Figure 5-25 Cross Connector for Current (Left) and Voltage Terminals (Right)
[dwkappst-030211-01.tif, 1, --_--]
Figure 5-26 Covering Cap for Current-Terminal Block

C53000-G5040-C002-K, Edition 11.2020
[dwkappsp-030211-01.tif, 1, --_--]
Figure 5-27 Covering Cap for Voltage-Terminal Block
Cover caps for sealing the connector interface of the terminal block can be ordered as accessories.
Terminal Designations
The current terminals have different designations in DIGSI, the configurator, and the device. The following
table provides an overview of the different terminal designations and order numbers of the terminals.
Terminal Configurator DIGSI Display on the Terminal Labeling Ordering No.
Device (Short Desig-
nation)
Modular Device 50/60 Hz
4 protection-class TypeA-Curr.term., 4x Current TBC4PROTA C73334A 1A187* P1Z51217
current transformers prot.tion 4x protection
3 protection-class TypeA-Curr.term., Current 3x TBC3PROTA1M C73334A 1A188* P1Z52917
current transformers 3xprot. 1xsens. prot., 1x sensi-
and 1 instrument tive
transformer
4 instrument trans- TypeA-Curr.term., 4x Current TBC4M C73334A 1A189* P1Z53617
formers measurem 4x sensitive
Modular Device 50/60/16.7 Hz
4 protection-class TypeA-Curr.term., 4x Current TBC4PROTA C73334A 1A177* P1Z512
current transformers prot. 4x protection
3 protection-class TypeA-Curr.term., Current 3x TBC3PROTA1M C73334A 1A178* P1Z529
transformer
4 instrument trans- TypeA-Curr.term., 4x Current TBC4M C73334A 1A179* P1Z536
formers measurem 4x sensitive
Non-Modular Device
4 protection-class TypeB-Curr.term., 4x Current TBC4PROTB C73334A 1A185* P1Z1869
current transformers prot. 4x protection
3 protection-class TypeB-Curr.term., Current 3x TBC3PROTB1M C73334A 1A186* P1Z1647
transformer
17 The equivalent 50/60/16.7-Hz terminal is used as a re-orderable single part.

C53000-G5040-C002-K, Edition 11.2020
5.7.2 Connections of Current Terminals
Fasteners
The fasteners for the transformer connection are part of the current terminal (housing side). They are made of
a stress-crack and corrosion-free alloy. The head shape of the clamping screw allows the use of a DIN 5.5 x 1.0
screwdriver or a PZ2 screwdriver. Siemens recommends a PZ2 screwdriver.
Connection Elements and Conductor Cross-Sections

The following connection types are possible:
• Stranded-wire conductor with ring-type lug
• Stranded-wire conductor with bootlace ferrule
• Solid conductor
Siemens recommends the use of ring-type lugs with the dimensions shown in the following figure. Use copper
cables only.
[dwringka-030211-01.tif, 1, en_US]
Figure 5-28 Ring-Type Lug
D (for bolt) 5.0 mm (0.2 in)

W 9.5 mm (0.37 in)
L 7.1 mm to 7.7 mm (0.28 in to 0.3 in)
In order to maintain the insulation route, you must use insulated cable lugs or you must insulate the crimping
zone (for example, by using heat-shrink tube insulation)
Siemens recommends ring-type lugs of the PIDG series made by Tyco Electronics.
Use copper conductors only, at least certified for a temperature of +105 °C. Use prepared solid conductors
intended for single or multi-wiring connection, maximum 2 wires per pole, and for usage of ferrules, crimped-
on pressure wire connectors (ring-type and pin-type).
2 terminal lugs can be installed for each connection.
[dwklest1-030211-01.tif, 1, --_--]
Figure 5-29 Example of a Current Terminal with Connection of Cross Connectors and Single Cables

C53000-G5040-C002-K, Edition 11.2020
[dwklest2-030211-01.tif, 1, --_--]
Figure 5-30 Example of a Current Terminal with Connection of 2 Single Cables
You can connect solid conductors as well as stranded-wire conductors with ring-type lug or bootlace ferrule.
For each connection, you can install up to 2 single cables of the same type and the same cross-section.
Bridges can be used as an alternative for horizontally arranged clamping points. If bridges are used, only ring-
type lugs may be used.
The following cable cross-sections can be used for the connection of single cables:
Cable cross-section AWG (American Wire Gauge) 14-10
(2.0 mm2 to 4.0 mm2 (0.0031 in2 to 0.0062 in2))
Ferrule with plastic shroud L = 10 mm (0.39 in) or L = 12 mm (0.47 in)
Stripped length 15 mm (0.59 in)
For use without ferrule Use solid copper cables only.
NOTE
i Always guide the solid conductor or stranded-wire conductor with bootlace from the left- or right-hand side
ferrule into the terminal. Making contact from the center is not permitted.
Mechanical Requirements
The fasteners and their associated components are designed for the following mechanical requirements:
Permissible tightening torque at clamping screw 2.7 Nm
For solid conductors, the max. permissible tightening
torque is 2 Nm.
Permissible tensile force for each connected 80 N following IEC 60947-1 (VDE 660, part 100)
conductor
5.7.3 Connections of Voltage Terminals
5.7.3.1 Connections of Voltage Terminals with Spring Clips
Fasteners
The fasteners for the voltage connection are part of the voltage terminal (housing side). They are made of a
stress-crack and corrosion-free alloy. The head shape of the clamping screw allows the use of a DIN 4.0 x 0.8
screwdriver or a PZ1 Phillips screwdriver. Siemens recommends a PZ1 Phillips screwdriver.

The single cable connection type is available for the connection. You can connect solid conductors as well as
stranded-wire conductors with and without bootlace ferrule as single cables. Siemens recommends using twin
bootlace ferrules of series PN 966 144 made by Tyco Electronics for the connection of 2 single cables.

C53000-G5040-C002-K, Edition 11.2020
Cable cross-section AWG (American Wire Gauge) 20-14 (0.5 mm2 to
2.5 mm2 (0.0008 in2 to 0.0039 in2)) solid
or bare stranded wire with or without UL listed boot-
lace ferrule
Use AWG 14 (2,5 mm2 (0.0039 in2)) for currents from
5 A to 10 A.
Use copper conductors only, at least certified for a
temperature of +105 °C (221 °F).
Bootlace ferrule with plastic shroud L = 12 mm (0.47 in)
Stripped length (for use without bootlace ferrule) 12 mm (0.47 in), only copper lines may be used.
Single cables and bridges can be connected together for horizontally arranged clamping points. Note that
adjacent bridges are installed reciprocally.
[dw_bootlace_ferrule, 1, en_US]
Figure 5-31 Twin Bootlace Ferrules
Permissible tensile force for each connected 50 N following IEC 60947-1 (VDE 660, part 100)
conductor
5.7.3.2 Connections of Voltage Terminals with Screw Connection

For connection of the following modules, Phoenix terminals are used (see Figure 5-23):
• Power-supply module PS203
• Plug-in module assembly with integrated power supply CB202
• Input module IO230, IO231, IO233
• Input and output module IO110, IO112, and IO113
• Measuring-transducer modules ANAI
• Temperature measurement module IO111

2.5 mm2 (0.0008 in2 to 0.0039 in2)) solid
lace ferrules
At least approved for a temperature of +105 °C (221
°F)
Bootlace ferrule with plastic shroud L = 8 mm to 10 mm (0.31 in to 0.39 in)

C53000-G5040-C002-K, Edition 11.2020
5.7.3.3 Connections of Voltage Terminal with Screw Connection for IO111

For the connection of the module IO111, Phoenix terminals are used (see Figure 5-24).

1.5 mm2 (0.0002 in2 to 0,0023 in2) solid
lace ferrules
At least approved for a temperature of +105 °C
(221 °F)
Bootlace ferrule with plastic shroud L = 9 mm (0,35 in)
Permissible tightening torque at clamping screw 0.22 Nm to 0.26 Nm
5.7.4 Installation and Removal
² Switch off the device before starting work.
Assembly tool
² Use a screwdriver (DIN 4 x 0.8).
Removal
² Use a screwdriver to carefully bend the left and right spring clips outwards.
² Carefully pull out the terminal block.
² Seal the contacts with a cover cap (see Figure 5-26 and Figure 5-27).
Installation
² Pull the cover cap off the terminal.
² Carefully insert the terminal block into the spring clips.
² Both spring clips must engage clearly audibly.

C53000-G5040-C002-K, Edition 11.2020
C53000-G5040-C002-K, Edition 11.2020
6 Technical Data
6.1 Analog Inputs 220

6.2 Supply Voltage 224
6.3 Binary Inputs 226
6.4 Relay Outputs 228
6.5 Light-Emitting Diodes in the On-Site Operation Panel 231
6.6 Communication Interfaces 232
6.7 Electrical Tests 235
6.8 Mechanical Tests 238
6.9 Environmental Conditions 239
6.10 Operating Conditions 241
6.11 Reference Conditions and Influencing Variables 242
6.12 Approvals 243
6.13 Design Data 244
6.14 Assembly Dimensions 247
6.15 Modular Device Name Plate 268
6.16 Name Plate of Non-Modular Devices (7xx81, 7xx82) 270
6.17 Name Plate, UL Approval, Base Module and 1/3 Base Module 271
6.18 Name Plate, UL Approval, Expansion Module 272
6.19 Battery 273
6.20 SDHC Memory Card 274
6.21 Display Resolution 275

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.1 Analog Inputs
6.1 Analog Inputs

Current Inputs
All current, voltage, and power data are specified as RMS values.
Rated frequency frated 50 Hz, 60 Hz
16.7 Hz (for rail protection devices only)
Protection-class current trans- Rated current Irated Measuring range of Measuring range of the
formers the modular devices non-modular devices
5A 0 A to 500 A 0 A to 250 A
1A 0 A to 100 A 0 A to 50 A
Instrument transformers 5A 0 A to 8 A 0 A to 8 A
1A 0 A to 1.6 A 0 A to 1.6 A
Burden for rated current Approx. 0.1 VA
Thermal rating 20 A continuously
(protection and instrument trans- 25 A for 3 min
formers) 30 A for 2 min
150 A for 10 s
500 A for 1 s
Dynamic load-carrying capacity 1250 A one half wave
GIS Low-Power Current Input (via Module IO240)
GIS-LPCT input Primary rated current Irated Measuring range
Kr ⋅ GIS-LPCT secondary rated value Kpcr = 50 (protection channel)
Kr = Transformation ratio of the Kpcr = 1.6 (measuring channel)
GIS-LPCT (DIGSI setting)
Refer to the GIS manual for the GIS-
LPCT secondary rated value.
Power consumption per current Max. 40 mVA
circuit at rated current Burden = 9.5 kΩ
Thermal rating Max. input voltage = 20 V
Accuracy Class 5TPE (protection channel)
Class 0.2S (measuring channel)
Voltage Input
16.7 Hz (for rail devices only)
Input and output modules IO102, IO202, IO208, IO211, IO215
IO214
Measuring range 0 V to 200 V 0 V to 7.07 V
Burden < 0.1 VA < 0.01 VA
Thermal rating 230 V continuously 20 V continuously

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.1 Analog Inputs
GIS Low-Power Voltage Input (via Module IO240)
GIS-LPVT input Primary rated voltage Vrated Measuring range
Kr ⋅ GIS-LPVT secondary rated value Kpcr = 2
Kr = Transformation ratio of the
GIS-LPVT (DIGSI setting)
Refer to the GIS manual for the GIS-
LPVT secondary rated value.
Power consumption per current Max. 1 mVA
circuit at rated current Burden = 50 Ω
Thermal rating Max. input current = 4.4 mA
Accuracy Class 0.1
NOTE
i For more information on the technical data of the current and voltage transformers, refer to the Technical
Data chapter in the SIPROTEC 5 Device manuals.
Measuring-Transducer Inputs (via Module ANAI-CA-4EL)
Insulation class SELV (Safety Extra Low Voltage) (according to IEC 60255-27)
Connector type 8-pin terminal spring
Differential current input channels 4
Measuring range DC -25.6 mA to +25.6 mA
Fault < 0.5 % of the measuring range
Input impedance 140 Ω
Permissible potential difference DC 20 V
between channels
Galvanic separation from ground/ DC 700 V
housing
Permissible overload DC 100 mA continuously
Measured-value repetition 200 ms
Inputs for Optical Sensors for Arc Protection (via Module ARC-CD-3FO)
Connector type AVAGO AFBR-4526Z

Number of transceivers 3
Fiber type Plastic Optical Fiber (POF) 1 mm
Receiver
Maximum -10 dBm ± 2 dBm
Minimum -40 dBm ± 2 dBm
Spectrum 400 nm to 1100 nm
Attenuation In the case of plastic optical fibers, you can expect a path attenuation of
0.2 dB/m. Additional attenuation comes from the plug and sensor head.
Optical budget18 Minimal 25 dB
Analog sampling rate 16 kHz
ADC type 10-bit successive approximation
18 All values in combination with sensors approved by Siemens.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.1 Analog Inputs
Transmitter
Type LED
Transmitter power Minimum 0 dBm
Maximum 2 dBm
Numerical aperture 0.5 19
Signal rate connection test 1 pulse per second
Pulse duration connection test 11 μs
High-Speed Measuring-Transducer Inputs, Voltage/Current (via IO210, IO212)
NOTE
i Current and voltage must not be connected at the same time to one measuring-transducer input. Instead,
only connect either current or voltage. For EMC reasons, do not connect a line to an unused input (current
or voltage).
Use shielded cables.
Table 6-1 High-Speed Measuring-Transducer Inputs, Voltage
Differential voltage input channels IO210: 420

IO212: 821
Measuring range DC -10 V to +10 V
Input impedance 48 kΩ
Max. permissible voltage with 300 V
respect to ground on the meas-
uring inputs
Permissible overload DC 20 V continuously
DC 60 V continuously (IO210 MT3 terminal point C9)
Table 6-2 High-Speed Measuring-Transducer Inputs, Current
Differential current input channels IO210: 422

IO212: 823
Measuring range DC -20 mA to +20 mA
Input impedance, current 12 Ω
Permissible potential difference DC 3.5 kV
between channels
Galvanic separation with respect to DC 3.5 kV
ground/housing
Permissible current overload DC 100 mA continuously
19 Numerical aperture (NA = sin θ (launch angle))

20 The IO210 has 4 high-speed measuring-transducer inputs. They can be used either as a voltage or current input.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.1 Analog Inputs
Table 6-3 Common Data for the Fast Measuring-Transducer Inputs, Voltage/Current

Insulation test voltage between the DC 3.5 kV
channels
Insulation test voltage with respect DC 3.5 kV
to ground/housing
Measured-value repetition 62.5 μs
Insulation class IO210 ELV (Extra Low Voltage) (as per IEC 60255-27)
Insulation class IO212 SELV (as per IEC 60255-27)
NOTE
i For more information on the measuring accuracy of the analog inputs, refer to the Technical Data chapter
in theSIPROTEC 5 Device manuals.
Temperature Inputs
Settings Value Note

Insulation class PELV (Protective Extra Low Voltage) –
(acc. to IEC 60255-27)
Measurement mode • Pt 100 Ω –
• Ni 100 Ω
• Ni 120 Ω
3-wire connection, shielded cables
Connector type 16-pin, 17-pin terminal spring –
Temperature measuring range -65 °C to +710 °C For PT100
-50 °C to +250 °C For NI100
-50 °C to +250 °C For NI120
Temperature Inputs (via Module IO240)
Settings Value
Sensor Type PT100 (Class F 0.3 EN 60751)
4-wire shielded cable connection
Measurement range -50 °C to +180 °C
Accuracy ±1 °C
LPIT Digital Input (via Module IO240)
Shield Cover Input

Sensor type Dry contact input
Measurement type Output voltage of 1 mA current injection @ max. DC 5 V

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.2 Supply Voltage
6.2 Supply Voltage

Integrated Power Supply
For modular devices, the following modules contain a power supply:
PS201 – Power supply of the base module and of the 1st device row
PS203 – Power supply of the 2nd device row
PS204 – Redundant power supply
CB202 – Plug-in module assembly with integrated power supply, for example, to accommodate communica-
tion modules
Permissible voltage DC 19 V to DC 60 V DC 48 V to DC 300 V
ranges AC 80 V to AC 265 V, 50 Hz/60 Hz
(PS201, PS203, PS204,
CB202)
Auxiliary rated voltage VH DC 24 V/DC 48 V DC 60 V/DC 110 V/DC 125 V/DC 220 V/
(PS201, PS203, PS204, DC 250 V or
CB202) AC 100 V/AC 115 V/AC 230 V, 50 Hz/60 Hz
Permissible voltage DC 19 V to DC 60 V DC 48 V to 150 V DC 88 V to DC 300 V
ranges (PS101) AC 80 V to AC 265 V,
Only for non-modular 50 Hz/60 Hz
devices
Auxiliary rated voltage VH DC 24 V/DC 48 V DC 60 V/DC 110 V/ DC 110 V/ DC 125 V/
(PS101) DC 125 V DC 220 V/DC 250 V
Only for non-modular or
devices AC 100 V/AC 115 V/
AC 230 V, 50 Hz/60 Hz
Superimposed alternating ≤ 15 % of the DC auxiliary rated voltage (applies only to direct voltage)
voltage, peak-to-peak,
IEC 60255-11,
IEC 61000-4-17
Inrush current ≤ 18 A
Recommended external Miniature circuit breaker 6 A, characteristic C according to IEC 60898
protection
Internal fuse
– DC 24 V to DC 48 V DC 60 V to DC 125 V DC 24 V to DC 48 V
AC 100 V to AC 230 V
PS101 4 A inert, AC 250 V, 2 A time-lag, AC 250 V, DC 300 V, UL recognized
Only for non-modular DC 150 V, SIBA type 179200 or Schurter type SPT 5x20
devices UL recognized
SIBA type 179200 or
Schurter type SPT 5x20
PS201, PS203, CB202 4 A inert, AC 250 V, 2 A time-lag, AC 250 V, DC 300 V, UL recognized
(to device version xA) DC 150 V, SIBA type 179200 or Schurter type SPT 5x20
UL recognized
SIBA type 179200 or
PS201, PS203, PS204 4 A inert, AC 250 V, 3.15 A time-lag, AC 250 V, DC 300 V, UL recognized
(Device version xB and DC 150 V, SIBA type 179200 or Schurter type SPT 5x20
higher) UL recognized
SIBA type 179200 or

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.2 Supply Voltage
Integrated Power Supply

Power consumption (life relay active)
– DC AC 230 V/50 Hz AC 115 V/50 Hz
1/3 module, non-modular 7 W 16 VA 12.5 VA
Without plug-in modules
1/3 base module, modular 13 W 55 VA 40 VA
Without plug-in modules
1/6 expansion module 3W 6 VA 6 VA
1/6 plug-in module 3.5 W 14 VA 7 VA
assembly without plug-in
modules (modules CB202)
Plug-in module for base <5W < 6 VA < 6 VA
module or plug-in module
assembly (for example,
communication module)
Stored-energy time for auxiliary voltage outage or For V ≥ DC 24 V ≥ 50 ms
short circuit, modular devices For V ≥ DC 110 V ≥ 50 ms
IEC 61000-4-11 For V ≥ AC 115 V ≥ 50 ms
IEC 61000-4-29
Stored-energy time for auxiliary voltage outage or For V ≥ DC 24 V ≥ 20 ms
short circuit, non-modular devices For V ≥ DC 60 V ≥ 50 ms
IEC 61000-4-11 For V ≥ AC 115 V ≥ 200 ms
IEC 61000-4-29

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.3 Binary Inputs
6.3 Binary Inputs

Standard Binary Input
Rated voltage range DC 24 V to 250 V

The binary inputs of SIPROTEC 5 are bipolar, with the exception of the
binary inputs on the modules IO230, IO231, and IO233.
Current consumption, excited Approx. DC 0.6 mA to 2.5 mA (independent of the control voltage)
Power consumption, max. 0.6 W
Pickup time Approx. 3 ms
Dropout time24 Capacitive load (supply-line capaci- Dropout time
tance)
< 5 nF < 4 ms
< 10 nF < 6 ms
< 50 nF < 10 ms
< 220 nF < 35 ms
Control voltage for all modules Adapt the binary-input threshold to be set in the device to the control
with binary inputs, except voltage.
module IO233 Range 1 for 24 V, 48 V, and 60 V Vlow ≤ DC 10 V
Control voltage Vhigh ≥ DC 19 V
Range 2 for 110 V and 125 V Vlow ≤ DC 44 V
Range 3 for 220 V and 250 V Vlow ≤ DC 88 V
Control voltage for binary inputs of Range for 125 V Vlow ≤ DC 85 V
the IO233 module Control voltage Vhigh ≥ DC 105 V
Maximum permitted voltage DC 300 V
The binary inputs contain interference suppression capacitors. To ensure EMC immunity, use the terminals
shown in the terminal diagrams/connection diagrams to connect the binary inputs to the common potential.
Special Binary Input with Maximized Robustness against Electrical Disturbances and Failures (IO216)
Rated voltage range DC 220 V

The special binary inputs of the SIPROTEC 5 with maximized robustness
against electrical disturbances and failures are bipolar and available only
on the module IO216.
Input impedance 50 kΩ to 60 kΩ
Rejection pulse charge > 200 µC
Current consumption, excited Approx. DC 1.2 mA to 2.0 mA (additionally to the current consumption
of the input impedance)
Power consumption, max. 1.5 W at DC 242 V
Pickup time Approx. 3 ms
24 For time-critical applications with low-active signals, consider the specified dropout times. If necessary, provide for active discharge
of the binary input (for example, a resistor in parallel to the binary input or using a change-over contact).

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.3 Binary Inputs
Dropout time25 Capacitive load (supply-line capaci- Dropout time

tance)
< 5 nF < 3 ms
< 10 nF < 4 ms
< 50 nF < 5 ms
< 220 nF < 10 ms
Control voltage for the module Range for 220 V control voltage
IO216 Threshold pickup 158 V to 170 V
Threshold dropout 132 V to 154 V
Maximum permitted voltage DC 300 V
The binary inputs contain interference suppression capacitors. To ensure EMC immunity, use the terminals
shown in the terminal diagrams/connection diagrams to connect the binary inputs to the common potential.
25 For time-critical applications with low-active signals, consider the specified dropout times. If necessary, provide for active discharge
of the binary input (for example, a resistor in parallel to the binary input or using a change-over contact).

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.4 Relay Outputs
6.4 Relay Outputs

Standard Relay (Type S)
Making capacity Max. 1000 W (L/R = 40 ms)

Max. 3600 VA (power factor ≤ 0.35, 50 Hz to 60 Hz)
Breaking capacity Max. 30 W (L/R = 40 ms)
AC and DC contact voltage 250 V
Permissible current per contact (continuous) 5A
Permissible current per contact (switching on and 30 A for 1 s (make contact)
holding)
Short-time current across closed contact 250 A for 30 ms
Total permissible current for contacts connected to 5A
common potential
Switching time OOT (Output Operating Time) Make time: typical: 8 ms; maximum: 10 ms
Additional delay of the output medium used Break time: typical: 2 ms; maximum: 5 ms
Max. rated data of the output contacts in accordance DC 24 V, 5 A, General Purpose
with UL certification DC 48 V, 0.8 A, General Purpose
DC 240 V, 0.1 A, General Purpose
AC 240 V, 5 A, General Purpose
AC 120 V, 1/6 hp
AC 250 V, 1/2 hp
B300
R300
Interference suppression capacitors across the 4.7 nF, ± 20 %, AC 250 V
contacts
Fast Relay (Type F)

Permissible current per contact (continuous) 5A
holding)
common potential
Switching time OOT (Output Operating Time) Make time: typical: 4 ms; maximum: 5 ms
Additional delay of the output medium used Break time: typical: 2 ms; maximum: 5 ms
Rated data of the output contacts in accordance with DC 24 V, 5 A, General Purpose
UL certification DC 48 V, 0.8 A, General Purpose
DC 240 V, 0.1 A, General Purpose
AC 250 V, 0.5 hp
B300
R300

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.4 Relay Outputs

contacts
Supervision 2-channel activation with cyclic testing (only for make
contact)
High-Speed Relay with Semiconductor Acceleration (Type HS)

Contact voltage AC 200 V, DC 250 V
Permissible current per contact (continuous) 5 A (according to UL certification)
10 A (no UL certification; AWG 14 / 2.5-mm2 (0.0039-
in2) copper conductors necessary)
holding)
Switching time OOT (Output Operating Time) Make time, typical: 0.2 ms; maximum: 0.2 ms
Additional delay of the output medium used Break time, typical: 9 ms; maximum: 9 ms
Rated data of the output contacts in accordance with B150
UL certification Q300
Power Relay (for Direct Control of Motor Switches)
Switching power for permanent and periodic operation

250 V/4.0 A 1000 W In order to prevent any damage, the external protec-
220 V/4.5 A 1000 W tion circuit must switch off the motor in case the rotor
110 V/5.0 A 550 W is blocked.
60 V/5.0 A 300 W
48 V/5.0 A 240 W
24 V/5.0 A 120 W
Turn on switching power for 30 s, recovery time until switching on again is 15 minutes.
For short-term switching operations, an impulse/pause ratio of 3 % must be considered.
100 V/9.0 A 1000 W Continuous and inching operation is not permitted.
60 V/10.0 A 600 W In order to prevent any damage, the external protec-
48 V/10.0 A 480 W tion circuit must switch off the motor in case the rotor
24 V/10.0 A 240 W is blocked.
Permissible continuous current per contact 5A
Permissible current per contact (switching on and 30 A for 1 s
holding)
common potential
Switching time OOT (Output Operating Time) ≤ 16 ms
Additional delay of the output medium used

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.4 Relay Outputs
Rated data of the output contacts in accordance with DC 300 V, 4.5 A – 30 s ON, 15 min OFF
UL certification DC 250 V, 1 hp motor – 30 s ON, 15 min OFF
DC 110 V, 3/4 hp motor – 30 s ON, 15 min OFF
DC 60 V, 10 A, 1/2 hp motor – 30 s ON, 15 min OFF
contacts
The power relays operate in interlocked mode, that is, only one relay of each switching pair picks up at a time
thereby avoiding a power-supply short circuit.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.5 Light-Emitting Diodes in the On-Site Operation Panel
6.5 Light-Emitting Diodes in the On-Site Operation Panel

Base Module
Status Color Quantity

RUN Green 1
ERROR Red 1
Routable (adjustable with DIGSI 5) 2-colored: red or green 16
Only the defined color can be used
in operation.
Expansion Module
Status Color Quantity

Routable Red 16 optional

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.6 Communication Interfaces

User Interface, Front Side
You can find a USB connection of type B for the connection to a laptop computer or to a PC on the front side of
the device. A protection cover protects this USB connection against pollution and humidity.
USB User interface
Connection USB type B
Insulation class PELV (Protective Extra Low Voltage) (according to IEC 60255-27)
Time-Synchronization Interface (Port G)

Time Synchronization External synchronization sources, for example, DCF77
IRIG B signal
Connection Rear
D-sub 9
Rated signal voltages DC 5 V, DC 12 V, or DC 24 V (optional)

Test voltage AC 500 V at 50 Hz
Insulation class SELV (according to IEC 60255-27)
Max. line length 10 m (0.39 in)
Table 6-4 Time-Synchronization Connection
Pin Signal Signal Description

1 P24-TSIG DC 24 V input
3 M-TSIG Return line Pxx-TSIG
4 M-TSYNC 26 Return line for P-TSYNC
5 Screen Shield potential
6 – –
8 P-TSYNC DC 24 V input
9 Screen Shield potential
26 Only for the PPS signal (GPS)

C53000-G5040-C002-K, Edition 11.2020
Technical Data
Signal Levels/ Signal Rated Input Voltage, DC

Burdens
5V 12 V 24 V
VImax 6.0 V 15.8 V 31.0 V
VIHigh ≥4.7 V ≥6.6 V ≥12.5 V
VILow ≤1.0 V at ≤1.4 V at ≤1.9 V at
IILow = 0.25 mA IILow = 0.25 mA IILow = 0.25 mA
IIHigh 4.5 mA to 9.4 mA 4.5 mA to 9.3 mA 4.5 mA to 8.7 mA
RI 890 Ω at VI = 4 V 1930 Ω at VI = 8.7 V 3780 Ω at VI = 17 V
640 Ω at VI = 6 V 1700 Ω at VI = 15.8 V 3560 Ω at VI = 31 V
On-Site Operation Panel for Surface-Mounting Housing (Port H) (Available only for Modular Devices)
The terminal for the on-site operation panel of surface-mounted devices is located on the D-sub 15 interface
(position H). The on-site operation panel of surface-mounted devices with integrated or detached on-site oper-
ation panel is connected to this interface.
User interface Detached on-site operation panel
Connection On the rear side
D-sub 15
Insulation class PELV (according to IEC 60255-27)
Integrated Ethernet Interface (Port J)

This terminal is used to load the device with DIGSI 5 using Ethernet. This terminal also enables IEC 61850
Ethernet communication or communication with another protocol via Ethernet, for example, for connecting
an external RTD unit.
Interface Integrated Ethernet interface
Connection
(1) LED 1: Yellow

(2) LED 2: Green
Insulation class SELV (acc. to IEC 60255-27)

C53000-G5040-C002-K, Edition 11.2020
Technical Data
Table 6-5 Connection

1 ETH_TX_P Transmit Data +
2 ETH_TX_N Transmit Data -
3 ETH_RX_P Receive Data +
4 – –
5 – –
6 ETH_RX_N Receive Data -
7 – –
8 – –
Screen Shield potential
LEDs of the RJ45 Terminals – Integrated Ethernet Interface (Port J)

The light-emitting diodes (LEDs) signal the operating state of the communication link. The operating states are
explained in the following table:
Integrated Ethernet Signal Color Operating Status
Interface (RJ45)
LED 1 ETH_LED1_N Yellow Continuously lit: 100 Mbit
Not lit: 10 Mbit
LED 2 ETH_LED0_N Green Flashing: Telegram reception
Continuously lit: No communication
Ethernet COM Link (Port K) (Available only for Modular Devices)

The Ethernet connection to the CB202 module (plug-in module assembly with integrated power supply) is
realized using the RJ45 interface.
The RJ45 interface can be used exclusively for the connection of the CB202 plug-in module assembly. This
terminal is left unused when no CB202 plug-in module assembly is in use.
The light-emitting diodes (LEDs) signal the operating state of the communication connection. The operating
states are explained in the following table:
COM Link (RJ45) Signal Color Operating State
LED 1 CL2_LED0_N Yellow Flashes when a communication module
is inserted in plug-in module position P
LED 2 CL3_LED0_N Green Flashes when a communication module
is inserted in plug-in module position N
Table 6-6 Connection

Siemens-specific assignment Connection using a special cable.
Is part of the device delivery.
Insulation class SELV (according to IEC 60255-27)
Plug-In Modules
You can find the Technical Data for plug-in modules in chapter 4 Plug-In Modules.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.7 Electrical Tests

Standards
IEC 60255 (product standard)
IEEE Std C37.90
UL 508
Additional standards are listed for the individual tests.
Installation Requirements
Overvoltage category III

Degree of pollution 2
Protection class 1
Voltage-Immunity and Safety Tests
Standards IEC 60255-27

Voltage test (routine test), current measurement inputs, voltage meas- AC 2.5 kV
urement inputs, relay outputs 50 Hz
Voltage test (routine test), DC 3.5 kV
Auxiliary voltage, binary inputs
Voltage test (routine test), only isolated communication and time- DC 700 V
synchronization interfaces and analog inputs (module position E, F, M,
N, and P)
Surge immunity test (type testing), all circuits except communication 5 kV (peak value)
and time-synchronization interfaces and analog inputs, class III 1.2 µs/50 µs
0.5 J
3 positive and 3 negative impulses
at intervals of 1 s
Insulation resistance > 100 MΩ @ DC 500 V
Resistor of protective-equipotential-bonding < 0.1 Ω @ DC 12 V, 30 A after
1 min.
Insulation of LPIT Digital Input (via Module IO240)
Insulation (All Inputs)

Configuration Each phase group (current, voltage, and temperature) is insulated from
each other, to PE and to the operator according to the requirements of the
IEC 61869-1 (AC 3 kV, 50 Hz, 1 min) and the IEC 60255-27 for a rated
voltage of 300 V despite the low-level signal voltages.
All channels are protected with differential-mode and common-mode
voltage-limiting devices.
Test levels (type test) AC 3250 V, 50 Hz, 1 min
6000 V 1.2/50 µs peak impulse

C53000-G5040-C002-K, Edition 11.2020
Technical Data
EMC Immunity Tests (Type Tests, Test under Mounting Conditions)
Standards IEC 60255-1 and -26 (product standards)

EN 61000-6-2 (generic standard)
Electrostatic discharge test Contact discharge:
IEC 61000-4-2
• Front-side modular and non-modular devices 8 kV
• Rear panel modular devices 8 kV
• Rear panel non-modular devices 6 kV
Air discharge 15 kV
Both polarities
150 pF
Ri = 330 Ω
Radiated electromagnetic field 20 V/m, 80 MHz to 1 GHz
immunity 10 V/m, 1 GHz to 6 GHz
Frequency sweep 80 % AM
IEC 61000-4-3 1 kHz
Radiated electromagnetic field 20 V/m, 80 MHz/160 MHz/380 MHz/450 MHz/900 MHz
immunity 10 V/1.85 GHz/2.15 GHz
Spot frequencies 80 % AM
IEC 61000-4-3 1 kHz
Dwell time ≥ 10 s
Electrical fast transient/burst 4 kV
immunity 5 ns/50 ns
IEC 61000-4-4 5 kHz
Burst length 15 ms
Repetition rate 300 ms
Both polarities
Ri = 50 Ω
Test duration ≥ 1 min
High-energy surge voltages Pulse: 1.2 µs/50 µs
IEC 61000-4-5 Auxiliary voltage Common mode: 4 kV, 12 Ω, 9 µF
Differential mode: 2 kV, 2 Ω, 18 µF
(device version xB and higher)
Differential mode: 1 kV, 2 Ω, 18 µF
(to device version xA)
and non-modular devices
Measuring inputs, binary inputs, Common mode: 4 kV, 42 Ω, 0.5 µF
and relay outputs Differential mode: 2 kV, 42 Ω,
0.5 µF
or varistor
Conducted RF, amplitude-modulated 10 V, 150 kHz to 80 MHz, 80 % AM,
IEC 61000-4-6 1 kHz
Conducted RF, amplitude-modulated 27 MHz/68 MHz at 10 V, dwell time
IEC 61000-4-6 ≥ 10 s
Spot frequencies 80 % AM, 1 kHz
Power frequency magnetic field 100 A/m (continuous)
immunity test 1000 A/m for 3 s
IEC 61000-4-8

C53000-G5040-C002-K, Edition 11.2020
Technical Data
Pulsed magnetic field 1000 A/m, 8 µs/20 µs

IEC 61000-4-9
Standard for Surge Withstand 2.5 kV (peak value)
Capability (SWC) 1 MHz
IEEE Std C37.90.1 τ = 15 µs
400 impulses per s
Test duration ≥ 10 s
Ri = 200 Ω
Common mode and differential mode test
Standard for Fast Transient Surge 4 kV
Withstand Capability 5 ns/50 ns
IEEE Std C37.90.127 5 kHz
Burst length 15 ms
Repetition rate 300 ms
Both polarities
Ri = 50 Ω
Test duration 60 s
Common mode and differential mode test
Standard for Withstand Capability 20 V/m
or Relay Systems to Radiated Elec- 80 MHz to 1 GHz
tromagnetic Interference from Pulse modulation (not valid for IO216)
Transceivers (Keying test)
IEEE Std C37.90.2
Damped oscillatory wave immunity 100 kHz, 1 MHz, 2.5 kV (peak value)
test 3 MHz, 10 MHz, 30 MHz, 2 kV (peak value)
IEC 61000-4-18 Test duration ≥ 60 s
Power-frequency disturbance varia- Zone A
bles at binary inputs 150 V (differential mode)
IEC 61000-4-16 300 V (common mode)
EMC Electromagnetic Emission Tests (Type Tests, Test under Mounting Conditions)
Standards IEC 60255-26 (product standard)

IEC 61000-6-4 (generic standard)
Conducted emission on auxiliary-voltage lines 150 kHz to 30 MHz limit class A
CISPR 22
Radiated emission CISPR 11 30 MHz to 1 000 MHz limit class A
CISPR 22 1 GHz to 6 GHz limit class A
Loading effect in electricity-supply systems, harmonics Does not apply!
Harmonic current emissions (see EN 61000-3-2, section 7,
power consumption < 75 W)
Loading effect in electricity-supply systems, voltage fluctuations Does not apply!
Flicker (see EN 61000-3-3, section 6, no
significant voltage fluctuations)
27 If a module ETH-BD-2FO is installed on a PS201 in the top slot (plug-in module position E in Figure 2-8), the immunity for this module
is currently restricted to 3.5 kV.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.8 Mechanical Tests
6.8 Mechanical Tests

Vibration and Shock Stress in Stationary Use
Standards IEC 60255-21 and IEC 60068

Vibration Test (sinusoidal) Sinusoidal 10 Hz to 60 Hz: ± 0.075 mm amplitude
IEC 60255-21-1, class 228 and 60 Hz to 150 Hz; 10 m/s2 acceleration
IEC 60068-2-6 Frequency sweep 1 octave/min
20 cycles in 3 axes perpendicular to one another
Shock Test Semi-sinusoidal
IEC 60255-21-2, class 1 Acceleration 50 m/s2
Duration 11 ms
3 shocks each in both directions of the 3 axes
Seismic Tests Sinusoidal 3 Hz 29 to 35 Hz:
IEC 60255-21-3, class 2 and Frequency sweep 1 octave/min
IEC 60068-3-3 1 cycle in 3 axes perpendicular to one another
3 Hz to 8 Hz: ± 7.5 mm amplitude (horizontal axes)
3 Hz to 8 Hz: ± 3.5 mm amplitude (vertical axis)
8 Hz to 35 Hz: 20 m/s2 acceleration (horizontal axes)
8 Hz to 35 Hz: 10 m/s2 acceleration (vertical axis)
Vibration and Shock Stress During Transport
Standards IEC 60255-21 and IEC 60068

Vibration Test (sinusoidal) Sinusoidal 5 Hz to 8 Hz: ± 7.5 mm amplitude
IEC 60255-21-1, class 230 and 8 Hz to 150 Hz: 20 m/s2 acceleration
IEC 60068-2-6 Frequency sweep 1 octave/min
20 cycles in 3 axes perpendicular to one another
Shock Test Semi-sinusoidal
IEC 60255-21-2, class 1 and Acceleration 150 m/s2
IEC 60068-2-27 Duration 11 ms
Continuous shock Semi-sinusoidal
IEC 60255-21-2, class 1 and Acceleration 100 m/s2
IEC 60068-2-27 Duration 16 ms
28 The non-modular devices in the assembly frame meet class 1.

29 For technical reasons, the frequency range is raised from 1 Hz to 3 Hz at the lower limit.
30 The non-modular devices in the assembly frame meet class 1.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.9 Environmental Conditions

Temperatures
Type test, in operation -25 °C to +85 °C

(in compliance with IEC 60068-2-1 and
IEC 60068-2-2, test Ad for 16 h and test Bd for 16 h)
Temporarily permissible during operation (tested for -25 °C to +70 °C
96 h) Load conditions for the non-modular devices: With
temperatures above 55 °C, no more than 50 % of the
binary inputs and relay outputs per printed circuit
board assembly are allowed to be continuously active.
Readability of the display may be impaired below
-10 °C and above +55 °C.
Recommended for uninterrupted duty -10 °C to +55 °C
(in compliance with IEC 60255-1)
Temperatures for continuous storage -25 °C to +55 °C
Type test, transport and storage for 16 h -40 °C to +85 °C
Heat-related limitations for the binary inputs on the IO216 input module (modular devices)
Switching thresholds Up to 55 °C Up to 70 °C
220 V operating voltage All 16 binary inputs usable for uninter- 10 binary inputs usable for uninter-
rupted duty rupted duty
Switching thresholds Up to 40 °C Up to 55 °C Up to 70 °C
Range 1 for 24 V, 48 V, All 48 binary inputs usable All 48 binary inputs usable All 48 binary inputs usable
and 60 V operating for uninterrupted duty for uninterrupted duty for uninterrupted duty
voltage
Range 2 for 110 V and All 48 binary inputs usable All 48 binary inputs usable 36 binary inputs usable
125 V operating voltage for uninterrupted duty for uninterrupted duty for uninterrupted duty
(max. 3 in each group of 4
at the same time)
Range 3 for 220 V and 36 binary inputs usable 24 binary inputs usable 12 binary inputs usable
(max. 3 in each group of 4 (max. 2 in each group of 4 (max. 1 in each group of 4
at the same time) at the same time) at the same time)
NOTE
i At an ambient temperature of 55 °C to 70 °C, a maximum of 36 relays per row can be switched on simulta-
neously.
Range 1 for 24 V, 48 V, All 24 binary inputs usable All 24 binary inputs usable All 24 binary inputs usable
and 60 V operating for uninterrupted duty for uninterrupted duty for uninterrupted duty
voltage

C53000-G5040-C002-K, Edition 11.2020
Technical Data
at the same time)
Range 3 for 220 V and 18 binary inputs usable 12 binary inputs usable 6 binary inputs usable for
250 V operating voltage for uninterrupted duty for uninterrupted duty uninterrupted duty
(max. 3 in each group of 4 (max. 2 in each group of 4 (max. 1 in each group of 4
at the same time) at the same time) at the same time)
at the same time)
Humidity
Permissible humidity stress ≤ 75 % relative humidity on the annual average

(according to IEC 60068-2-30) Up to 93 % relative humidity on 56 days a year
Transient condensation is permissible.
Arrange the devices so that they are not exposed to
direct sunlight or extreme temperature changes. This
will prevent condensation in the device.
Constant humid heat, 56 days 40 °C, 93 % relative humidity
Humid heat, cyclical 12 h + 12 h cycles
25 °C/55 °C/95 % relative humidity
Other Environmental Information
Maximum operating altitude above sea level 2000 m (6561.68 ft)

Minimum permissible atmospheric pressure 783.8 hPa
Corrosion Tests
Corrosion test SO2 (IEC 60068-2-42) 25 ppm

Corrosion test H2S (IEC 60068-2-43) 10 ppm
Mixed gas corrosion test (IEC 60068-2-60 and SO2 300 ppb, SO2 1250 ppb, H2S 100, CL2 20 ppb
ISA 71.04 G3)
Humidity, cyclic (IEC 60068-2-30 and LR test specifi- 25 °C (93 %), 55 °C (97 %) for 6 cycles of 24 hours
cation Section 14) each
Dust and sand test Lc Arizona dust for 24 hours
Salt mist (IEC 60068-2-52) Method 1 (40 °C, 90 % to 95 %) for 28 days

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.10 Operating Conditions
6.10 Operating Conditions

The protection device is designed for flush mounting in conventional relay rooms and systems such that elec-
tromagnetic compatibility (EMC) is ensured with proper flush mounting.
Siemens additionally recommends:
• Use contactors and relays that work within the same cabinet or the same relay panel with digital protec-
tion equipment, only with suitable quenching equipment.
• With switchgear rated at 100 kV or higher, provide external connecting lines with shielding grounded at
both ends that is capable of carrying current. No special measures are necessary in medium-voltage
systems.
• Removing or plugging in individual modules under live voltage is prohibited. Some components are elec-
trostatically sensitive in the removed state. Pay attention to the ESD specifications (Electrostatically Sensi-
tive Devices). There is no danger for the components when they are installed.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.11 Reference Conditions and Influencing Variables
6.11 Reference Conditions and Influencing Variables

Reference Conditions
Measurand current I Irated ± 1 %

Measurand voltage V Vrated ± 1 %
Frequency f frated ± 1 %
Sine waveform, total harmonic distortion ≤5%
Ambient temperature TV 23 °C ± 1 °C
(73.4 °F ± 2 °F)
Auxiliary voltage VAux VAux,rated ± 1 %
Warmup time ≥ 15 min
External fields/external influences None
Variables Influencing Pickup and Dropout Thresholds (Protection)
Auxiliary voltage: 0.8 VAux,rated up to 1.2 VAux,rated ≤ 0.2 %

Ambient temperature: -10 °C to 55 °C ≤ 0.5 %/10 K
Frequency: 45 Hz to 65 Hz ≤1%
Harmonics
≤1%
• Up to 10 % of 3rd harmonics
≤1%
• Up to 10 % of 5th harmonics
Warmup ≤ 0.3 %
Transient excess pickup in fundamental component measurement ≤5%
method for τ > 100 ms (with complete unbalance)
EMC interference ≤5%
Variables Influencing the Measured Values (Fault Recorders)
Auxiliary voltage: 0.8 VAux,rated up to 1.2 VAux,rated ≤ 0.2 %

Ambient temperature: -10 °C to 55 °C ≤ 0.5 %/10 K
Frequency: 45 Hz to 65 Hz ≤1%
Harmonics
≤1%
• Up to 10 % of 3rd harmonics
≤1%
• Up to 10 % of 5th harmonics
Warmup ≤ 0.3 %
Transient excess pickup in fundamental component measurement ≤5%
method for τ > 100 ms (with complete unbalance)
EMC interference 31 ≤ 1.5 %
31 Use shielded cables for the current and voltage measuring inputs on the fault recorder.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.12 Approvals
6.12 Approvals
UL-Listed/UL-Approved
Base module and 1/3 base module IND. CONT. EQ. 69CA
Expansion module IND. CONT. EQ. 69CA

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.13 Design Data
6.13 Design Data

Masses
Device Size
Weight of the Modular Devices
Type of construction 1/3 1/2 2/3 5/6 1/1
Flush-mounting device 4.4 kg 7.2 kg 9.9 kg 12.7 kg 15.5 kg
Surface-mounted device with inte- 7.4 kg 11.7 kg 15.9 kg 20.2 kg 24.5 kg
grated on-site operation panel
Surface-mounted device with 4.7 kg 7.8 kg 10.8 kg 13.9 kg 17.0 kg
detached on-site operation panel
Size Weight
Detached on-site operation panel 1/3 1.9 kg
Detached on-site operation panel 1/6 1.1 kg
Device Size
Weight of the Non-Modular Devices 7xx81, 7xx82
Type of construction 1/3
Flush-mounting device 3.6 kg
Bracket for non-modular surface- 1.9 kg
mounted variant
Dimensions of the Base and 1/3 Modules
Type of Construction (Maximum Dimensions) Width over all x Height over all x Depth (incl.
Current Terminal), Width and Depth Each Rounded
up to the Next Full mm (in Inches)
Flush-mounting device 150 mm x 266 mm x 229 mm
(5.91 x 10.47 x 9.02)
Surface-mounted device with integrated on-site oper- 150 mm x 314 mm x 337 mm
ation panel (5.91 x 12.36 x 13.27)
Surface-mounted device with detached on-site opera- 150 mm x 314 mm x 230 mm
tion panel (5.91 x 12.36 x 9.06)
Dimensions of the Device Rows
Type of Width over all x Height over all x Depth (incl. Current Terminal), Width and Depth
Construction Each Rounded up to the Next Full mm (in Inches)
(Maximum
Dimensions)
Type of construc- 1/3 1/2 2/3 5/6 1/1
tion
Flush-mounting 150 mm x 225 mm x 300 mm x 375 mm x 450 mm x
device 266 mm x 266 mm x 266 mm x 266 mm x 266 mm x
229 mm 229 mm 229 mm 229 mm 229 mm
(5.91 x 10.47 x (8.86 x 10.47 x (11.81 x 10.47 x (14.76 x 10.47 x (17.72 x 10.47 x
9.02) 9.02) 9.02) 9.02) 9.02)

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.13 Design Data
Type of Width over all x Height over all x Depth (incl. Current Terminal), Width and Depth
Construction Each Rounded up to the Next Full mm (in Inches)
(Maximum
Dimensions)
Surface- 150 mm x 225 mm x 300 mm x 375 mm x 450 mm x
mounted device 314 mm x 314 mm x 314 mm x 314 mm x 314 mm x
with integrated 337 mm 337 mm 337 mm 337 mm 337 mm
on-site operation (5.91 x 12.36 x (8.86 x 12.36 x (11.81 x 12.36 x (14.76 x 12.36 x (17.72 x 12.36 x
panel 13.27) 13.27) 13.27) 13.27) 13.27)
Surface- 150 mm x 225 mm x 300 mm x 375 mm x 450 mm x
mounted device 314 mm x 314 mm x 314 mm x 314 mm x 314 mm x
with detached 230 mm 230 mm 230 mm 230 mm 230 mm
on-site operation (5.91 x 12.36 x (8.86 x 12.36 x (11.81 x 12.36 x (14.76 x 12.36 x (17.72 x 12.36 x
panel 9.06) 9.06) 9.06) 9.06) 9.06)
Expansion Module Dimensions
Type of Construction (Maximum Dimensions) Width x Height x Depth, Width and Depth Each
Rounded up to the Next Full mm (in Inches)
Flush-mounting device 75 mm x 266 mm x 229 mm
(2.95 x 10.47 x 9.02)
Surface-mounted device with integrated on-site oper- 75 mm x 314 mm x 337 mm
ation panel (2.95 x 12.36 x 13.27)
Surface-mounted device with detached on-site opera- 75 mm x 314 mm x 230 mm
tion panel (2.95 x 12.36 x 9.06)
Plug-In Module Dimensions
Type of Construction (Maximum Dimensions) Width x Height x Depth (in Inches)

USART-Ax-xEL, ETH-Bx-xEL 61 mm x 45 mm x 120.5 mm
(2.4 x 1.77 x 4.74)
USART-Ax-xFO, ETH-Bx-xFO (without protection 61 mm x 45 mm x 132.5 mm
cover) (2.4 x 1.77 x 5.22)
ANAI-CA-4EL 61 mm x 45 mm x 119.5 mm
(2.4 x 1.77 x 4.7)
ARC-CD-3FO 61 mm x 45 mm x 120.5 mm
(2.4 x 1.77 x 4.74)
Minimum Bending Radii of the Connecting Cables Between the On-Site Operation Panel and the Base Module
Fiber-optic cable R = 50 mm
Pay attention to the length of the cable protection
sleeve, which you must also include in calculations.
D-Sub cable R = 50 mm (minimum bending radius)
Degree of Protection According to IEC 60529
For equipment in the surface-mounted housing IP5432 for front

For equipment in the flush-mounting housing IP5432 for front
For operator protection (back side) IP2x for current terminal (installed)
IP2x for voltage terminal (installed)
32 The provided plug-in label must be used for expansion modules with LEDs.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.13 Design Data
Degree of pollution, IEC 60255-27 2

Maximum operating altitude above sea level 2000 m (6561.68 ft)
UL Note
Type 1 if mounted into a door or front cover of an enclosure.

When expanding the device with the 2nd device row, then they must be mounted completely inside an
enclosure.
Tightening Torques for Terminal Screws
Type of Line Current Terminal Voltage Terminal with Voltage Terminal with
(also see Figure 5-22) Spring-Loaded Terminals Screw Connection
(also see Figure 5-22) (also see Figure 5-23)
Stranded wires with ring- 2.7 Nm No ring-type lug No ring-type lug
type lug
Stranded wires with boot- 2.7 Nm 1.0 Nm 0.6 Nm
lace ferrules or pin-type
lugs
Solid conductor, bare 2.0 Nm 1.0 Nm –
(2 mm2)
Bare stranded wire Not permitted 1 Nm 0.6 Nm
NOTE
i For current and voltage terminals, the maximum speed of the tool must not exceed 640 rpm.
NOTE
i Use copper cables only.
Torques for Other Screw Types
Screw Type Torque

M4 x 20 1.2 Nm
M4 x 8 1.2 Nm
M2.5 x 6 0.39 Nm
Countersunk screw, M2.5 x 6 0.39 Nm
Countersunk screw, M2.5 x 8 0.39 Nm
Collar screw, M4 x 20 0.7 Nm

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.14 Assembly Dimensions
NOTE
i You must mount the devices vertically.
Flush-Mounting Device
[dw_z1_1-3, 2, en_US]
Figure 6-1 Cut-Out Widths and Drilling Pattern – 1/3 Device, 1st Device Row

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dw_z1_1-2, 2, en_US]

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dw_z1_2-3, 2, en_US]

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dw_z1_5-6, 2, en_US]
[dw_z1_1-1, 3, en_US]

C53000-G5040-C002-K, Edition 11.2020
Technical Data
All drillings in the area of the specific device cut-out widths (see Table 6-7) must comply with the dimensions
in the corresponding figures.
[dw_z2_2-6, 2, en_US]
Figure 6-6 Cut-Out Widths and Drilling Pattern – 1/3 Device, 2nd Device Row

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dw_z2_3-6, 2, en_US]
[dw_z2_4-6, 2, en_US]

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dw_z2_5-6, 2, en_US]
[dw_z2_6-6, 3, en_US]

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dw_first and second device row, 1, en_US]
Figure 6-11 Drilling Pattern – 1/1 Devices, 1st and 2nd Device Row
Siemens recommends a drilling space of at least 55 mm (2.17 in) between the 1st and 2nd device row. Due to
the connecting-cable length, the maximum space may be approx. 80 mm (3.15 in). The length of the cable is
890 mm (35.04 in) from the center of the plug to the center of the plug.
[dw_angle rail, 1, en_US]
Figure 6-12 Angle Rail for Connection of the 1st and 2nd Device Row
Table 6-7 Cut-Out Widths
Width of the Assembly Opening in mm (in Inches)

1/3 device (base module) 146+2 mm (5.75+0.08)
1/2 device (base module with one expansion module) 221+2 mm (8.7+0.08)
2/3 device (base module with 2 expansion modules) 296+2 mm (11.65+0.08)

C53000-G5040-C002-K, Edition 11.2020
Technical Data
Width of the Assembly Opening in mm (in Inches)

Table 6-8 Variable Housing Widths
Dimension a
Housing Widths in mm (in Inches)
(Total Width: Housing Width + 4.6 mm (0.18 in))
1/3 device 145 (5.71)
1/2 device 220 (8.66)
2/3 device 295 (11.61)
5/6 device 370 (14.57)
1/1 device 445 (17.52)
[dw_surface_mounting_in, 2, en_US]
Figure 6-13 Flush-Mounting Devices, Dimensions from the Side and Front Views

C53000-G5040-C002-K, Edition 11.2020
Technical Data
Surface-Mounted Devices with Integrated On-Site Operation Panel (Modular Device)
[dwosopin-070211-01.tif, 3, en_US]
Figure 6-14 1/3 Surface-Mounted Device with Integrated On-Site Operation Panel, Dimensions in the Side
and Front Views
NOTE
i For surface-mounted devices, make sure that the drillings fit for a screw of the size M6.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dwbohrge-1_3.vsd, 2, en_US]
Figure 6-15 Drilling Pattern of a 1/3 Surface-Mounted Device – 1st Device Row

C53000-G5040-C002-K, Edition 11.2020
Technical Data

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dwbohrge-070211-01.tif, 3, en_US]
[dw_z2_bohr_1-3.vsd, 2, en_US]
Figure 6-20 Drilling Pattern of a 1/3 Surface-Mounted Device – 2nd Device Row

C53000-G5040-C002-K, Edition 11.2020
Technical Data

C53000-G5040-C002-K, Edition 11.2020
Technical Data

C53000-G5040-C002-K, Edition 11.2020
Technical Data

C53000-G5040-C002-K, Edition 11.2020
Technical Data
Surface-Mounted Devices with Integrated On-Site Operation Panel (Non-Modular Device)
[dw_console side view.vsd, 3, en_US]
Figure 6-25 Non-Modular Surface-Mounted Device with Integrated On-Site Operation Panel, Dimensions
from the Side and Front Views
Surface-Mounted Devices with Integrated On-Site Operation Panel (Non-Modular Device)
NOTE
i For surface-mounted devices, make sure that the drillings fit for a screw of the size M6.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dw_drilling non modular surface mounting with several consoles, 1, en_US]
Figure 6-26 Drilling Pattern of a Non-Modular Surface-Mounted Device – Several Consoles
* The 149 mm are valid if several mounted consoles are to be mounted next to each other.
Surface-Mounted Devices with Detached On-Site Operation Panel

You can find more information on the drilling patterns for the devices in section Surface-Mounted Devices
with Integrated On-Site Operation Panel (Modular Device) , Page 256.
[dw_z1_osop_1-3, 1, en_US]
Figure 6-27 Drilling Pattern of the On-Site Operation Panel of the 1/3 Device

C53000-G5040-C002-K, Edition 11.2020
Technical Data

C53000-G5040-C002-K, Edition 11.2020
Technical Data

C53000-G5040-C002-K, Edition 11.2020
Technical Data
[dwosopab-070211-01.tif, 3, en_US]
Figure 6-32 Surface-Mounted Device with Detached On-Site Operation Panel, Dimensions in the Side and
Front Views
Refer to Table 6-8 for the variable dimension a.

The drilling patterns correspond to the figures Figure 6-15 to Figure 6-24.
The cable length for the detached operation panel is up to 5 m (196.85 in).
NOTE
i Cables with a length of 5 m (196.85 in) are only specified for PCs and laptop computers with a USB2
connection. These cables are not specified for PCs and laptop computers with a USB3 connection.
Cables with a length of 2.5 m (98.43 in) are specified for USB2 and USB3 connections.
[dw_angel-bracket_without_relief-cutouts, 1, en_US]
Figure 6-33 Angle Rail with Assembly Dimensions

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.15 Modular Device Name Plate

In the following table, the name plate of a modular device is explained as an example. The name plate is
located on the device.
7SJ85 Device type or, in the case of expansion modules, designa-

tion of the printed circuit board assembly
Overcurrent Protection Product group
Irated, Urated, frated Rated values (which are specified when current and/or
voltage transformers are placed on the printed circuit board
assembly)
Iload This value is specified when relays are placed on the printed
circuit board assembly.
Vaux Values for the power supply
P1JXXXXXXXXXX Technical Numbering System (TNS), maximum 18 digits
BMXXXXXXXXXX Serial number
QR code
BB The device hardware supports the operation of a redundant

power supply module.
The letter combinations have the following meaning:
• xA: Power supply not capable of redundancy

• xB: Power supply capable of redundancy
Insulation test of the voltage inputs, current inputs, and
binary outputs with AC 2.5 kV
Insulation test of the power supply (Vaux) and binary inputs
(BI) with DC 3.5 kV
Insulation testing of all sealed-off interfaces with DC 700 V
E, F, M, N, P Designation of the ports into which the plug-in modules are

plugged.
5 kV impulse voltage test [type test] in compliance with
Class III

C53000-G5040-C002-K, Edition 11.2020
Technical Data
European CE marking
Pay attention to the overall documentation for the device

(Product information, Device manual, Hardware manual,
Operating manual, and Communication protocol manuals)

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.16 Name Plate of Non-Modular Devices (7xx81, 7xx82)
6.16 Name Plate of Non-Modular Devices (7xx81, 7xx82)

In the following table, the name plate of a non-modular device is explained as an example. The name plate is
located on the device.
7SJ82 Device type

Overcurrent Protection Product group
IO110 IO102 Designation of the I/O modules
Irated, Vrated, frated Rated values (which are specified when current and/or
voltage transformers are placed on the module.)
Iload This value is specified when relays are placed on the
module.
Vaux Values for the power supply
P1JXXXXXXXXXX Technical Numbering System (TNS), maximum 18 digits
BMXXXXXXXXXX Serial number
QR code
Insulation test of the voltage inputs, current inputs, and

binary outputs with AC 2.5 kV
Insulation test of the power supply (Vaux) and binary inputs
(BI) with DC 3.5 kV
Insulation testing of all sealed-off interfaces with DC 700 V
E, F Designation of the ports into which the plug-in modules are

plugged.
5 kV impulse voltage test [type test] in compliance with
Class III
European CE marking
Pay attention to the overall documentation for the device

(Product information, Device manual, Hardware manual,
Operating manual, and Communication protocol manuals)

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.17 Name Plate, UL Approval, Base Module and 1/3 Base Module
6.17 Name Plate, UL Approval, Base Module and 1/3 Base Module
UL approved for Canada and the USA
IND. CONT. EQ. Industrial controller

69CA Approval number
tSurr: max. 70 °C normal op. The ambient temperature must not exceed 70 °C or 158 °F
during normal operation.
Paux: max. 120 VA Maximum power consumption of the device
For additional output ratings see product infor- For additional output ratings see Product information.
mation

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.18 Name Plate, UL Approval, Expansion Module
6.18 Name Plate, UL Approval, Expansion Module
UL approved for Canada and the USA
IND. CONT. EQ. Industrial controller

69CA Approval number
tSurr: max. 70 °C normal op. The ambient temperature must not exceed 70 °C or 158 °F
during normal operation.
Listed accessory for use with manufacturer´s Approved accessory for use with a protection device from
protection relay. Siemens

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.19 Battery
6.19 Battery
Type CR2032
Button cell
Lithium
Voltage 3V
Capacity 230 mAh
Average service life of the battery, unpowered after removal of protec- At least 6 months
tive film
Service life of the battery in the activated state with protective film 10 years
removed
Use button cells from manufacturers like Varta, Panasonic, or Duracell.
NOTE
i After the Battery fault indication, you must replace the battery within 2 weeks. If ignored, data loss may
occur.

C53000-G5040-C002-K, Edition 11.2020
Technical Data
NOTE
i You can use only Siemens SDHC memory cards.
Capacity 16 GB33
Performance class ≥ Class 10
Temperature range -40 °C to +85 °C
Flash type SLC
Dimensions
Width x Height x Depth (in Inches)

SDHC memory card 24 mm x 32 mm x 2.1 mm (0.94 x 1.26 x 0.08)
33 Usable capacity: Approx. 15 GB

C53000-G5040-C002-K, Edition 11.2020
Technical Data
6.21 Display Resolution
6.21 Display Resolution

LCD Graphic display (Liquid Crystal Display) Small 192 x 128 pixels
LCD Graphic display (Liquid Crystal Display) Large 240 x 320 pixels

C53000-G5040-C002-K, Edition 11.2020
C53000-G5040-C002-K, Edition 11.2020
7 Ordering Information
7.1 Ordering Spare Parts and Accessories 278

C53000-G5040-C002-K, Edition 11.2020
Ordering Information
7.1 Ordering Spare Parts and Accessories
7.1.1 Order Configurator and Order Options
Order Configurator
The order configurator assists you in the selection of SIPROTEC 5 products. The order configurator is a Web
application that can be used with any browser. The order configurator can be used to configure complete
devices or individual components, such as communication modules, expansion modules, or other accessories.
At the end of the configuration process, the product code and a detailed presentation of the configuration
result are provided. The product code unambiguously describes the selected product and also serves as an
order number.
Ordering Options
The following ordering options are possible for SIPROTEC 5 products:
• Device
• Single part
• DIGSI 5
• Functional enhancement
NOTE
i To order single parts in the order configurator, use the Single part link.
Individual parts are:
• Expansion module
• Plug-in module
• Sensors for arc protection
• Operation panel
• Terminal
• Accessories
7.1.2 Ordering Accessories
NOTE
i To order terminals, terminal accessories, and mechanical accessories in the order configurator, use the
Single part link.
Table 7-1 Accessories
Group Accessories
Terminal Voltage terminal, terminal block, 14-pole
Terminal Voltage terminal (power supply)
Terminal block, 2-pole34
Terminal Type A current terminal, 4 x protection
(for modular devices)
34 Recommended tightening torque when screwing down the terminal on the rear plate: 0.3 Nm

C53000-G5040-C002-K, Edition 11.2020
Group Accessories
Terminal Type A current terminal, 3 x protection and 1 x measurement
Terminal Type A current terminal, 4 x measurement
Terminal Type B current terminal, 4 x protection
(for non-modular devices)
Terminal Type B current terminal, 3 x protection and 1 x measurement
(for non-modular devices)
Terminal 2-pole cross connector for current terminal
Terminal Terminals for IO110, IO112, IO11334
Terminal Terminals and shielding for IO11134,35,36
Terminal Terminal set only for IO23x34
Terminal 2-pole cross connector for voltage terminal
Terminal Cover for current terminal block
Terminal Cover for voltage terminal block
Terminal Transport safety, current terminal
Terminal Transport safety, voltage terminal
Terminal Terminal set for direct connection to 400 V low voltage
Accessories USB covers (10 each for CP 100, 200, 300)
Accessories Cable, integrated operation panel, 0.43 m
Accessories Cable, detached operation panel, 2.50 m
Accessories Cable, detached operation panel, 5.00 m
Accessories Cable set, COM link cable
Accessories Cover plate for plug-in modules
Accessories Cover panel 1/6, 5 pcs
Accessories Set of angle rails
Accessories 10 x labeling strip, LEDs/function keys
Accessories 5 x labeling strips, push-buttons
Accessories Set of parts, mounting bracket 1/2
Accessories 4 x screw cover 1/3, type C11
Accessories 2 x bus termination plate
Accessories Assembly frame for panel surface mounting for non-modular
devices 7xx81 and 7xx82 devices
Accessories SDHC memory card for 7KE85
Accessories 10 x battery holder
Accessories Connecting cable for 2nd row
Accessories DIGSI 5 USB cable 2.0
Accessories SFP RJ45, 10 units
Accessories SFP Single-mode, 24 km, 10 units
Sensors for arc protection Point sensor with line length of 3 m
35 The set consists of terminals and shielding for the IO111 for the terminal positions M and N.
36 Only for non-modular devices 7xx82

C53000-G5040-C002-K, Edition 11.2020
Group Accessories
Sensors for arc protection Line sensor, length 3 m
Sensors for arc protection Supply line for line sensors, length 3 m

C53000-G5040-C002-K, Edition 11.2020
A Appendix
A.1 Hardware/Firmware Compatibility List 282

C53000-G5040-C002-K, Edition 11.2020
Appendix
A.1 Hardware/Firmware Compatibility List
Non-Modular (7xx82)
Non-Modular (7xx81)
Modular
V01.00
V02.00
V03.00
V04.00
V05.00
V06.01
V06.10
V07.00
V07.30
V07.50
V07.60
V07.80
V07.82
V07.90
V08.01
V08.03
V08.30
V08.40
Component/
Product Feature
Modules
CP100 – ■ ■ – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
PS101 – ■ ■ – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO101 – ■ ■ – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO102 – ■ ■ – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO103 – ■ – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO110 – ■ – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO111 – ■ – – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■
IO112 – – ■ – – – – – – – – – – – – – ■ ■ ■ ■ ■
IO113 – – ■ – – – – – – – – – – – – – ■ ■ ■ ■ ■
CP200 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ – – – – – – –
CP300_1 ■ – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
CP300_237 ■ – – – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■
PS201 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
CB202 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
PS203 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
PS204 ■ – – – – – – – – – – – – – – ■ ■ ■ ■ ■ ■
IO201 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO202 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO203 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO204 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO205 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO206 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO207 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO208 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO209 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO210 ■ – – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO211 ■ – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO212 ■ – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO214 ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO215 ■ – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO216 ■ – – – – – – – – – – – – – – – ■ ■ ■ ■ ■
IO230 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO231 ■ – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
IO233 ■ – – – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■
IO240 ■ – – – – – – – – – – – – – – – – – ■ ■ ■
37 Security-chip upgrade

C53000-G5040-C002-K, Edition 11.2020
Appendix
Non-Modular (7xx82)
Non-Modular (7xx81)
Modular
V01.00
V02.00
V03.00
V04.00
V05.00
V06.01
V06.10
V07.00
V07.30
V07.50
V07.60
V07.80
V07.82
V07.90
V08.01
V08.03
V08.30
V08.40
Component/
Product Feature
Plug-In Modules
USART-AB-1EL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AC-2EL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AD-1FO ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AE-2FO ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AF-1LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AG-1LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AH-1LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AJ-1LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AK-1LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AU-2LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AV-2LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AW-2LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AX-2LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
USART-AY-2LDFO ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
ETH-BA-2EL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
ETH-BB-2FO ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
ETH-BD-2FO ■ – – – – – – – – – – – – – – – ■ ■ ■ ■ ■
ANAI-CA-4EL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
ARC-CD-3FO ■ ■ ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
LED Push-Buttons
12 LEDs – – ■ – – – – – – – – – – – – – ■ ■ ■ ■ ■
16 LEDs ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
32 LEDs ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
48 LEDs ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
64 LEDs ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
80 LEDs ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
8 push-buttons/LEDs (NE) + ■ – – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
16 LEDs
32 LEDs
48 LEDs
64 LEDs
Significant Features
2-end-fault protection38 ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
3-end-fault protection38 ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Multi-end-fault protection38 ■ ■ – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
38 Only available for devices 7SD* and 7SL*

C53000-G5040-C002-K, Edition 11.2020
Appendix
Non-Modular (7xx82)
Non-Modular (7xx81)
Modular
V01.00
V02.00
V03.00
V04.00
V05.00
V06.01
V06.10
V07.00
V07.30
V07.50
V07.60
V07.80
V07.82
V07.90
V08.01
V08.03
V08.30
V08.40
Component/
Product Feature
8 current/voltage trans- ■ – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
formers39
16 current/voltage trans- ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
formers39
24 current/voltage trans- ■ – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
formers39
formers39
formers39
1 zone, 3 fields incl.40 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
2 zones, 4 fields incl.40 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
2 zones, 4 fields incl. TrAbb40 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
4 zones, 6 fields incl.40 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
4 zones, 6 fields incl. TrAbb40 ■ – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
4Z, 6F incl., TrAbb, only ■ – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
CBFP40
FE: 6 zones40 ■ – – – – – – – – – – – – – – – – – – – ■
FE: 20 zones40 ■ – – – – – – – – – – – – – – – – – – – ■
FE: 20 zones, only circuit- ■ – – – – – – – – – – – – – – – – – – – ■
breaker failure protection40
FE: 6 zones, incl. TrAbb40 ■ – – – – – – – – – – – – – – – – – – – ■
FE: 20 zones, incl. TrAbb40 ■ – – – – – – – – – – – – – – – – – – – ■
4 synchronization points40 ■ – – – – – – – – – – – – – – – – – – – ■
8 synchronization points40 ■ – – – – – – – – – – – – – – – – – – – ■
Function Points
I base ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Base + 10 function points ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
39 Only available for 7KE devices*

40 Only available for device 7SS85

C53000-G5040-C002-K, Edition 11.2020
Appendix
Non-Modular (7xx82)
Non-Modular (7xx81)
Modular
V01.00
V02.00
V03.00
V04.00
V05.00
V06.01
V06.10
V07.00
V07.30
V07.50
V07.60
V07.80
V07.82
V07.90
V08.01
V08.03
V08.30
V08.40
Component/
Product Feature
Base + 600 function points ■ ■ ■ – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Integrated Ethernet RJ45
For DIGSI 5 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
DIGSI 5 and IEC 61850/ ■ – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
limited
DIGSI 5 and IEC 61850/ – ■ ■ – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
GOOSE with CP100
DIGSI 5 and IEC 61850/ ■ – – – – – – – – – ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
GOOSE with CP300

C53000-G5040-C002-K, Edition 11.2020
C53000-G5040-C002-K, Edition 11.2020
Literature
/1/ Distance Protection, Line Differential Protection, and Overcurrent Protection for 3-Pole Tripping – 7SA82,
7SD82, 7SL82, 7SA84, 7SD84, 7SA86, 7SD86, 7SL86, 7SJ86
C53000-G5040-C010
/2/ Distance and Line Differential Protection, Breaker Management for 1-Pole and 3-Pole Tripping – 7SA87,
7SD87, 7SL87, 7VK87
C53000-G5040-C011
/3/ Overcurrent Protection – 7SJ82/7SJ85
C53000-G5040-C017
/4/ Overcurrent Protection – 7SJ81
C53000-G5040-C079
/5/ Motor Protection – 7SK82/85
C53000-G5040-C024
/6/ Transformer Differential Protection – 7UT82, 7UT85, 7UT86, 7UT87
C53000-G5040-C016
/7/ Generator Protection – 7UM85
C53000-G5040-C027
/8/ Busbar Protection – 7SS85
C53000-G5040-C019
/9/ High-Voltage Bay Controller – 6MD85/86
C53000-G5040-C015
/10/ Paralleling Device – 7VE85
C53000-G5040-C071
/11/ Universal Protection – 7SX85
C53000-G5040-C607
/12/ Merging Unit 6MU85
C53000-G5040-C074
/13/ Fault Recorder – 7KE85
C53000-G5040-C018
/14/ Hardware Description
C53000-G5040-C002
/15/ Communication Protocols
C53000-L1840-C055
/16/ Process Bus
C53000-H3040-C054
/17/ DIGSI 5 – Software Description
C53000-D5040-C001
/18/ SIPROTEC 5 – Security
C53000-H5040-C081

C53000-G5040-C002-K, Edition 11.2020
Literature
/19/ PIXIT, PICS, TICS IEC 61850

C53000-G5040-C013
/20/ Operation
C53000-G5040-C003
/21/ Engineering Guide
C53000-G5040-C004

C53000-G5040-C002-K, Edition 11.2020
Glossary
Control display
The control display becomes visible for devices with a large display after pressing the Control key. The diagram
contains the switching devices to be controlled in the feeder. The control display serves for implementing
switching operations. Specification of this diagram forms part of configuring.
DCF77
The precise official time is determined in Germany by the Physikalisch-Technische Bundesanstalt PTB in Bruns-
wick. The atomic clock unit of the PTB transmits this time via the long-wave time signal transmitter in Main-
flingen near Frankfurt/Main. The emitted time signal can be received within a radius of approx. 1500 km from
Frankfurt/Main.
GOOSE
Generic Object-Oriented Substation Event
Ground
The conductive ground whose electric potential can be set equal to 0 at every point. In the area of grounding
conductors, the ground can have a potential diverging from 0. The term reference ground is also used for
this situation.
Grounding
The grounding is the entirety of all means and measuring for grounding.
IEC
International Electrotechnical Commission - International electrotechnical standardization body
Parameterization
Comprehensive term for all setting work on the device. You can set parameters for the protection functions
with DIGSI 5 or sometimes also directly on the device.
PB Client
Process-bus Client. The subscriber of Sampled Measured Values can also be called process-bus client.
RSTP
Rapid Spanning Tree Protocol
SFP
Small Form-Factor Pluggable
SNMP
Simple Network Management Protocol

C53000-G5040-C002-K, Edition 11.2020
Glossary
SNTP
Simple Network Time Protocol

C53000-G5040-C002-K, Edition 11.2020
Index
A Expansion module 27
Dimensions 244, 274
Activating the battery 180 Display elements 43
Arc protection Expansion module 46
Installing the line sensor 203 On-site operation panel with push-button func-
Installing the point sensor 201 tion 46
Line sensor 203 Drilling pattern
Plug-in module 178 Flush-mounting device 247
Point sensor 200 Surface-mounted devices variant of non-modular
Assembly dimensions devices 263
Flush-mounting device 247 Surface-mounted devices with detached on-site
Surface-mounted devices variant of non-modular operation panel 264
devices 263 Surface-mounted devices with integrated on-site
Surface-mounted devices with detached on-site operation panel 256
operation panel 264
Surface-mounted devices with integrated on-site
operation panel 256
E
Electrical inspection 180
B EMC test 236, 237
Ethernet interface
Battery 206 PS101 127
Battery compartment 206 PS201 53, 54
C F
Communication module 153, 156 Flush-mounting device 22

Ethernet module 171 Expanding 182
Module designation 156, 156 Flush-mounting device with 2nd device row
Optical 164 Expand 184
Serial 161
Conductor cross-section 214
Connecting a device 180
I
Cross connectors 211, 211
Current and voltage terminals
IEC 60529 245
Installing 217
Installation requirements 235
Removing 217
Instrument transformers 211
Current terminals 211, 214
Insulation test 235
Integrated Ethernet interface
Connection 234
D LEDs 234
Device structure
Base module 22

C53000-G5040-C002-K, Edition 11.2020
Index
M Replacement 209
Secure Digital High Capacity 209
Measuring-transducer module 177 Spring clip 211
Modular systems 19 Standards 235
Surface-mounted device with 2nd device row
Expanding 189
Surface-mounted device with detached on-site operation
O panel 37
Expanding 192
On-site operation panel Surface-mounted device with integrated on-site opera-
PS201 53 tion panel
On-site Operation Panel Expanding 186, 188
LEDs 231 Modular device 31
On-site operation panel with push-button function 46 Non-modular 33
Operating elements 43
Expansion module 46
On-site operation panel with push-button func-
tion 46
T
Order configurator 278
Ordering Terminal and connection diagram
Accessories 278 IO101 130
Individual components 278 IO102 133
IO103 136
IO110 139
IO111 142
P IO112 147
IO113 149
Plug-in module assembly CB202 61 IO201 67
Plug-in module position IO202 70
Base module 156 IO203 73
Expansion module with CB202 156 IO204 76
Plug-in modules IO205 79
Fasteners 195 IO206 82
Install 195 IO207 84
Removing 196 IO208 87
Plug-In Modules IO209 90
Replacement 198 IO210 93
Power-supply module IO211 96
PS101 124, 126 IO212 99
PS101 terminals 125 IO214 102
PS201 50, 52 IO215 103
PS201 terminals 51 IO216 104, 105
Protection-class current transformers 211 IO230 107
PS204 57 IO231 111
IO233 113
PS204 60
Terminals and Connection Diagram
R IO240 117
Time synchronization
Ring-type lug 214 Connection 232
RJ45 socket 159 Interface 232
RS485 159 PS101 126
PS201 53
S
V
SDHC memory card
Data 274 Voltage terminals 211, 215, 216, 217

C53000-G5040-C002-K, Edition 11.2020

SIP5 Hardware V08.40 Manual C002-K en

Uploaded by

Copyright:

Available Formats

SIP5 Hardware V08.40 Manual C002-K en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SIP5 Hardware V08.40 Manual C002-K en

Uploaded by

Copyright:

Available Formats

Preface

Open Source Software

Disclaimer of Liability Copyright

Purpose of the Manual

SIPROTEC 5, Hardware Description, Manual 3

• Communication protocol manual

• Process bus manual

• DIGSI 5 online help

• SIPROTEC 5/DIGSI 5 Tutorial

• Selection guide for SIPROTEC and Reyrolle

4 SIPROTEC 5, Hardware Description, Manual

IND. CONT. EQ.

Customer Support Center

SIPROTEC 5, Hardware Description, Manual 5

Qualified Electrical Engineering Personnel

• Proper storage, setup and installation

• Proper operation and maintenance

Selection of Used Symbols on the Device

Nr. Symbol Description

1 Direct current, IEC 60417, 5031

2 Alternating current, IEC 60417, 5032

6 SIPROTEC 5, Hardware Description, Manual

Nr. Symbol Description

3 Direct and alternating current, IEC 60417, 5033

4 Earth (ground) terminal, IEC 60417, 5017

5 Protective conductor terminal, IEC 60417, 5019

6 Caution, risk of electric shock

7 Caution, risk of danger, ISO 7000, 0434

8 Protective Insulation, IEC 60417, 5172, Safety Class II devices

9 Guideline 2002/96/EC for electrical and electronic devices

10 Guideline for the Eurasian Market

SIPROTEC 5, Hardware Description, Manual 7

• Switch to online mode.

• Select the device.

• Select Online in the menu bar.

• Click Show open source software information.

SIPROTEC 5, Hardware Description, Manual 9

Open Source Software..................................................................................................................................9

2 Forms of Devices and On-Site Operation Panels........................................................................................ 21

SIPROTEC 5, Hardware Description, Manual 11

12 SIPROTEC 5, Hardware Description, Manual

3.3 Power-Supply Module of Non-Modular Devices (7xx81, 7xx82)........................................124

SIPROTEC 5, Hardware Description, Manual 13

4.2.5.2 ETH-BA-2EL.......................................................................................................... 173

5 Working on the Device............................................................................................................................. 179

6 Technical Data.......................................................................................................................................... 219

14 SIPROTEC 5, Hardware Description, Manual

6.2 Supply Voltage................................................................................................................224

7 Ordering Information............................................................................................................................... 277

SIPROTEC 5, Hardware Description, Manual 15

1.1 Advantages of SIPROTEC 5 18

SIPROTEC 5, Hardware Description, Manual 17

1.1 Advantages of SIPROTEC 5

• You save time because of jumperless devices.

• The freely configurable, modular device design creates more flexibility.

• You save time because of prewired terminal blocks.

• Operation is uncomplicated and intuitive.

• Multi-colored LEDs ensure safe system management.

18 SIPROTEC 5, Hardware Description, Manual