Technical specification Parts

Display A B C
Resolution 800 x 480 Inst
Installation

ENGL
Installation Ma

ISH
ENGL
Installation Manual

ISH
ENGL
alla Manua

ISH
tion nual

ENGL
ISH
Ma l
nua
l

Brightness >1200 nits

ban
dg.
com com com com
ban ban ban
dg. dg. dg.
Touch screen Full touch screen (multi-touch)
Viewing angles D E F
(typical value at contrast ratio = 10)
Left/right: 70°, top: 50°, bottom: 60° P3007
Electrical Installation Guide
Supply voltage 12/24 V DC (9.0 - 31.2 V DC min - max) G H
680 mA/ 330 mA at 12 V DC (backlight full/off )
Power consumption
380 mA/200 mA at 24 V DC (backlight full/off )
Recommended fuse rating (12 V / 24 V) 3A
Environmental
A. P3007 unit
Temperature range -15°C to +55°C (5°F to 131°F)
B. Panel mounting kit
Storage temperature -20°C to +60°C (4°F to 140°F)
C. Documentation
Waterproof rating IPX2
D. Power cable
Category Protected
Shock, vibration and humidity According to IEC 60945 E. Communication cable

Interface/Connectivity F. Fuse kit

Ethernet 1x (RJ45) 100Base-TXS, 8P8C connector, IPv4 G. Bracket kit

Maximum data rate 450 sps addressed to device, 500 sps unintended H. Suncover (sold separately)
Buffer capacity Dynamic serial buffer *988-12389-001*

NMEA 2000 1x (Micro-C ,1 LEN)

Data card reader 1x slot (microSD)
Comms
IEC 61162-2 ports 2x
System examples
Digital input 1x
Analog input 1x GPS GPS GPS

Power output (+16 V DC, 70 mA) 1x

Physical
Compass Safe Distance - Metric, imperial 0.5 m (1.64 ft)
P2005 / P3007 P2005 / P3007 P2005 / P3007
Weight (display only) 1.32 kg (2.91 lbs) T BACKLIGHT
For product manuals, technical specifications, certificates and declarations, refer to the product website: MOB KEY CONTROL SPEED
http://www.navico-commercial.com

Bracket mounting Dimensional drawings

220.0 mm 174.0 mm T
(8.66”) (6.85”) T
197.0 mm 8.0 mm 74.7 mm
(7.76”) (0.32”) (2.94”)
141.0 mm
154.9 mm

(5.56”)

MX JUNCTION BOX
(6.10”)

T
ANALOG
CAN BUS CAN BUS CAN BUS NMEA 0183/
DIGITAL ETHERNET
TERMINATOR BACKBONE DROP CABLES IEC 61162-1/-2
202.2 mm 61.9 mm FREQUENCY
(7.96”) (2.44”)
Connector overview Communication cable
A. NMEA 2000, Micro-C connector Refer to the Operator Manual for software setup. Wiring illustrations only include the required wires for the example.
B. Ethernet, RJ45 connector IEC 61162-2
C. Power and external alarm, 4-pin connector It is possible to configure port 1 and 2 for direct antenna connection or port 2 for BAM connection.
D. Ground, M4 threaded insert
Pin/Wire Color IEC 61162-2 port 1 IEC 61162-2 port 2
E. Comms (communication), 19-pin connector 3 pink TX common
4 yellow listener (RX_B)
5 blue listener (RX_A)
A B C D E
6 brown/white RX common
15 red/black talker (TX_B)
16 purple/white talker (TX_A)
7 red/white RX common
Power and external alarm 8 purple listener (RX_A)
9 orange listener (RX_B)
A. DC negative - black D. Alarm output negative return - blue
10 black/white TX common
B. +12/24 V DC - red E. Alarm output (N/C isolated contact) - yellow
17 green/white talker (TX_A)
C. Fuse (3 A) F. Alert management system
18 orange/white talker (TX_B)
A B 19 Not applicable

C Direct antenna connection

D E IEC 61162-2 port 1 GPS antenna IEC 61162-2 port 2 GPS antenna
F 8 GPS primary output (TX_A) 4 GPS secondary output (TX_B)
¼¼ Note: Refer to the technical specification for electrical details. 9 GPS primary output (TX_B) 5 GPS secondary output (TX_A)
17 GPS control input (RX_A)
18 GPS control input (RX_B)

Ethernet NMEA 2000 Analog input

The unit is equipped with a standard RJ-45 connector. The unit is equipped with a standard Micro-C connector. The analog port can be configured for backlight control.
¼¼ Note: Network switches can be used to extend the Pin/wire Color Backlight control A. Potentiometer (10 k - 100 k Ohm, 0.1 W)
network. Routers and repeater hubs shall not be used. 2 red +16 V DC (max. 70 mA) 2 11 A
11 blue/white signal in
12 brown not used
13 grey ground 13
14 green not used

Digital input
Grounding The digital port can be used for either speed input or as an external MOB key.
A. Ground, M4 threaded insert Pin/wire Color Speed log MOB
A
B. Grounding cable, min. 0.82 mm2 ( 18 AWG) 1 light green signal in signal in
C. Star washer B C D 13 grey ground ground
D. Screw (M4-.7 X 6 mm) 14 green not used not used

MOB Speed

A. Momentary push button A speed log that outputs 200 pulses per nautical mile can
be connected to the digital port.
1 A 1
A. Speed log (200 pulses/NM)
A
B. Ship’s ground
13 B
¼¼ Note: It is recommended that the unit ground is connected to the vessel’s bonded ground or a non-bonded RF ground. 13