I'NCINEER - Vol. XXXX, No. 03, pp.

31-38,2007
O Tlie Institution of Engineers, Sri Lanka

Discharge Measurements in Open Channels using

Compound Sharp-Crested Weirs
M. Piratheepan, N.E.F. Winston and K.P.P. Pathirana

Abstract: Compound sharp-crested weirs have been widely used for measuring discharges in open
channels accurately with a reasonable sensitivity over a wide flow range. The flow characteristic over a
compound sharp-crested weir is completely different to that over a single sharp-crested weir. The most
common type of compound sharp-crested weir used in irrigation canals is the combination of a
rectangular notch and a 'V notch with a small notch angle. However, the continuity of flow and
precision of this type of compound weirs are reported to be poor in the transition region between two
sections. As an improvement, a compound sharp-crested weir composed of two triangular parts with
different notch angles has been designed and experimentally validated which proved to be accurate in
measuring a wide range of discharges without any discontinuity. Several methods are also proposed to
estimate the flow over the double 'V notch compound sharp-crested weir and one method is
experimentally validated as most suitable.
Keywords: Compound sharp-crested weir, Discharge coefficient, Steady uniform flow

1. Introduction 'V notch with a small notch angle. But it has

been already found that the accuracy of flow
Accurate flow measurement in open channels is measurements of this type of structure is poor in
very important in many civil engineering the transition region between the two parts.
applications. There are different types of Therefore, in order to overcome this problem
structures available for flow measurements such and also to measure flow rates accurately for a
as weirs, orifice, flumes, sluice gates etc. The wide range of discharges, the use of a
structures used for flow measurements should compound sharp-crested weir having a
he accurate, economical and easy to use combination of two triangular weirs with
(installation, operation and maintenance). Weirs different notch angles has been studied. This
allow water to be routed through a structure of paper presents the details of the experimental
known dimensions, permitting flow rates to be investigations conducted with a compound
measured as a function of depth of flow through sharp-crested weir having two triangular 'V
the structure. Among different types of weirs, a notches with different notch angles for
.sharp-crested weir has been widely used for estimating discharge accurately over a wide
discharge measurements in open channels. The range of flows.
commonly used cross sections of sharp-crested
weirs are rectangular, trapezoidal and 2. Literature Review
triangular. A triangular weir with a small notch
angle is found to be accurate in discharge Many studies have been carried out in the past
measurements; however, it can only be used to to investigate the discharge over sharp-crested
measure small discharges. When measuring weirs with fully and partially developed flows.
high discharges by using the single sharp- Henderson [8] presented an elementary analysis
crested weirs, backwater effects might affect the for discharge over a sharp-crested weir by
structures located upstream of the weir. assuming that the flow does not contract as it
passes over the weir. By assuming that the
When the discharge is to be measured
pressure across the whole water column over
accurately with a reasonable sensitivity over a
wide range of flows, the use of compound M.Piratheepan, B.Sc. Eng. (Hons), Department of Civil Engineering,
University of Peradeniya.
sharp-crested weirs could be an appropriate
N.E.F.Winston, B.Sc. Eng. (Hons), Department of Civil Engineering,
solution. The most commonly used compound University of Peradeniya.
sharp-crested weirs used in irrigation canals Eng.(Dr.) K.P.P. Pathirana, B.Sc. Eng. (Hons.) (Peradeniya), M.Eng.,
have a combination of rectangular notch and a Ph.D., C.Eng., FIE(SL), MICE (London), Senior Lecturer, Department
of Civil Engineering, University of Peradeniya.

31 ENGINEER
the weir is atmospheric the following equation V-notch and the occasionally occurring larger
was derived for discharge as, flows by the rectangular weir. However, the
discontinuity in the discharge curve has been a
o ra
— Qd t a n - 2.5
(1)
major problem in the above stated combination
15 \2 of notches when measuring discharge in the
transition range. To avoid this problem Martinez
Where, Q= discharge; C= discharge coefficient; et al. [10] proposed a compound sharp-crested
g = gravitational acceleration; 6 = notch angle; weir which has two triangular weirs with
and h = head over the weir. different notch angles. They proposed and
validated a theoretical discharge equation for
Some of the researchers adjust the head over the fully contracted flow condition by conducting
weir to eliminate the effects of lateral and the experiment with different combinations of
vertical contractions with the limitation of notch angles.
applicability (Bos [4], Brater et al. [5],
Kindswater et al. [9] and Chow [7]). Later a In this paper various methods of estimating
correction factor (K) has been introduced to the discharge over the compound sharp-crested
head over the weir by considering the surface weir, having a combination of two triangular
tension and viscous effects (USER [13]). The weirs in partially contracted flow conditions are
discharge coefficient solely depends on the compared based on the experimental
notch angle for fully developed flow and investigations. The most suitable method of
depends on many other parameters for partially computing discharge over the compound weir is
developed flow. It is recommended in BSI [6] proposed. The accuracy and continuity of
that the head over the weir need to be adjusted discharge measurements using this type of
for both partially and fully contracted flows. As compound weirs are also discussed.
all the references show similar curves for C,and
K without providing the equations for them, 3. Theoretical Aspects
LMNO Engineering [12] used a curve fitting
program to obtain the following relationships A weir is considered to be a sharp-crested weir,
for Cd and K, both of which are related to notch when the crest thickness is between 1 mm and 2
angle of weir, mm. when the thickness exceeds the specified
limits, it is required to be bevelled to at least 600
=0.6072-0.000874<9 + 6. (2) for triangular weirs and at least 450 for
rectangular weirs. The bevelled section should
£=4.42-0.10350+1.005x10~36'2-3.24xlO~66'3 (3) be faced towards the downstream. The tail
water level should be low enough to ensure the
free fall of the nappe.
Where, 6 is the notch angle. The specifications
and the proper installation of weirs for flow The discharge equation for the sharp-crested
measurements in both partially and fully weir is obtained by integrating the flow through
contracted flow conditions are clearly discussed a small elemental strip over the nappe at the
in BSI and USER [13]. weir; where each flow strip, is considered with a
different head. The discharge equation for a
Very few studies are reported in the past on
typical triangular weir is given in Eq.(l). The
compound sharp-crested weirs with the aim of
discharge over the compound weir with two
improving the performance of single sharp-
triangular weir sections is calculated by adding
crested weir. Abdel-Azim et al. [1] discussed the
the flow through the triangular areas 1 & 2 and
characteristics of the combined flow over weirs
subtracting the flow through the intersected
and below gates of equal contraction for the
triangular area as shown in Figure-1. The Cd
purpose of avoiding the problem of sediment
values for the lower 'V notch and the upper 'V
accumulation upstream from the weir. On the
notch are calculated separately and used to
other hand, the characteristics of a compound
predict the flow. Eq.l can be used to predict the
weir consisting of a rectangular notch with a V-
flow over the weir when head over the weir (h)
notch cut into the centre of the crest are
is less than the lower weir height (hO) and in this
discussed in the USER [13], and this could
case, the discharge coefficient corresponding to
handle the normal range of discharges by lower
the lower 'V notch is used. When the head over

ENGINEER 32
the weir is greater than hff six different methods e=
arc proposed to estimate the flow over the
[T] (* -
compound weirs, which are presented in detail (5)
in the following sections.

Where, x is the height of the intersection

triangle.

Method-3

It is the same as 'Method -1' but replacing the Cd

of the intersection triangle corresponding to the
upper 'V notch.

(6)

Method -4

It is the same as 'Method -2' but replacing the C1

of the intersection triangle corresponding to the
lower 'V notch.

\'\%ure 1- Typical cross section of the compound (7)

sharp-crested-weirs (a & b)
.,2.5

Method -1
In Method-5 & Method-6, it is considered that
I lore, the intersection triangle is in the upper 'V the intersection triangles do not contact with
notch and hence, the Cd corresponding to this any solid boundaries and therefore, the Cd
area is taken as the lower 'V notch discharge values for the intersection triangles are
coefficient. eliminated.

4. Experimental Details
(4) The experiments were carried out in the
Hydraulics Laboratory of the Faculty of
Engineering, University of Peradeniya. The
Where Cd = discharge coefficient of the lower 'V experimental set-up mainly consists of a
notch, Ca= discharge coefficient of the upper 'V rectangular circulating open channel of 12 m
notch, 9j = lower notch angle and 92 = upper long, 0.3 m wide and 0.3 m deep and a collecting
notch angle. tank at the downstream end of the channel. The
compound sharp-crested weirs were built of GI
Method -2 plates and attached at the end of the open
channel with the help of G-clamps and water
I lere, the intersection triangle is in the lower 'V sealant to prevent leakages.
notch and hence, the Cd corresponding to this
area is taken as the upper 'V notch discharge The downstream collecting tank consists of two
coefficient (see Figure 1 (b)). perforated plates to avoid the turbulence caused
by the nappe from the elevated channel. A

33 ENGINEER
 From overhead To overhead

"1
tank Upstream tank

Main channel „
Compound ,
Weir. /
'
/
_'
V- notch Sump
(a.} Plan view

From overhead tank Upstream tank Main channel

U =31
/
, / /
/ Compound'
^ Downstream tank

V-notch

To sump
(b) End elevation

Figure 2. Schematic diagram of the experimental set-up (-not to scale-).

schematic diagram of the experimental set-up is checked by conducting the trials with different
shown in Figure 2. 'rj values for these single 'V notches.

Water was supplied to the main channel from an Altogether eight combinations of double 'V
overhead tank at constant head and the flow notches were tested by changing 6^, 62 and lower
was controlled by a gate valve. The flow was 'V notch height (see Table 1). Discharge in the
confirmed as steady uniform by the help of the channel was increased in steps of nearly 1 L/s
backwater height measurements at subsequent during experiments. Table 2 shows a summary
intervals. The actual discharge through the of experimental data used for different test
channel was measured by means of the 'V notch cases.
attached to the downstream collecting tank. For
Table 1: Combinations of 'V notches
this purpose, initially it was calibrated
Compound Height of Lower Upper
accurately by using a volumetric method. The weir type the lower notch notch
water depth was measured from a fixed height 'V notch angle (0t) angle
along the centre line of the main channel using a (fc/cm) (0.)
point gauge with an accuracy of 0.0508 mm (0.02 1 15 60° 90°
inch). 2 15 60° 120°
3 15 60° 150°
Initially, several experimental runs were carried
4 10 90° 120°
out with single 'V notches having 60°, 90°, 120° 5 10 90° 150°
& 150° notch angles to find out their discharge 6 10 60° 90°
coefficients. Due to the proximity of the walls of 7 10 60° 120°
the approach channel, the contractions are not 8 10 60° 150°
fully developed. So the notch is defined as a
partially contracted, triangular thin-plate weir. Table 2: Summary of experimental data
As the flow conditions exceed the limitation Parameter Range
prescribed for partially contracted flow in BSI
Main channel discharge, (L/s) 0.30 - 13.12
(1965) and USER (1997), the effect of the weir Upstream depth of flow, (m) 0.09 - 0.23
height (p) on the discharge coefficients was Weir height, p (cm) 2.5 - 10.0

ENGINEER 34
 5.1 Continuity of flow
The continuity of flow over the compound weirs
for variation of head is checked using
experimental data. As a typical result, the
variation of measured discharge with head for
compound weir types 6, 7 and 8 is shown in
Figure 4.

14 -,

12 -

3. - The experimental set-up

8 -
5. Data Analysis o
co
^
The analysis of experimental data is aimed at
checking the continuity of flow over the
compound weir, suitability of the equations 2 -
proposed for discharge computations (Sec. 3)
and the accuracy of the proposed weir for ) 50 100 150 200
discharge measurements. The 'V notch attached Head o\«r the weir(mm)
to the downstream collecting tank is calibrated --«--Type6 —*—Type7 - - • - • T y p e 8
precisely and Qis calculated as 0.627. As stated Figure 4 - Variation of measured discharge with head
earlier, the Cd values for the single 'V notches for compound weir types 6, 7 and 8.
are computed by changing the weir height p.
The Cd values for the 90° *V notch are given in As can be noted, there is no discontinuity of
Table 3 as a typical result. flow shown at the transition region of the two
triangular notches. This is not the case with
Tible 3: Cd values of 90° 'V notch with changing compound weirs having a rectangular notch
weir heights with a V notch at the centre, where the discharge
Height of the weir p/(cm) £1 versus head relationship is not continuous and
2.5 0.7061 as a result, when the head is near the transition
4.0 0.7005 region the flow measurements are not very
5.0 0.6943 accurate. Such difficulties could be overcome
7.5 0.6942 with the use of compound weirs having double
10.0 0.7035 'V notches as suggested during this study.
By considering the values given in Table 3, it can
be noted that there is not much deviation of Cd 5.2 Selection of best method
values for different values of p. Therefore, the Discharges over the compound sharp-crested
effect of p value on the discharge coefficient is weirs for all test cases are computed by using six
rtssumed to be negligible within the different methods outlined in section 3. The
experimental range covered in this study. comparison between measured and computed
I lence, the p value is not taken as a variable for discharges is shown in Figure 5.
the remaining test cases. The C, values for single
' V notches are tabulated in Table 4. It can be seen that the discharge computed by
using methods 2, 4 and 6 have highly under-
Table 4: Cd values of single 'V notches estimated the discharge over the compound
Notch Angle
weirs, whereas methods 1, 3 and 5 appear to be
Discharge Coefficient (C,)
more suitable for estimating the discharge over
60° 0.654
90° 0.694
the compound weir.
120° 0.663 In order to compare the six different methods
150° 0.761
suggested in this study for estimating the

35 ENGINEER
 100 - Gc
E = (9)
N G

Where Ga and Gc are the actual and computed

discharges, respectively. N is the number of test
runs examined for a particular method.
According to the Figures 6 and 7, it can be noted
that the method 3 is the most accurate one for
computing discharge over compound sharp-
crested weirs having double 'V 'notches. Figure
8 illustrates the comparison between measured
discharges with the discharge computed using
4 6 8 1 0 1 2 method 3.
Measured Discharges (L/s)
. Mtd 1 Mtd 2 4 Mtd 3! ; Mtd 4l x Mtd 5 Mtd6i
18 -,
figure 5. Comparison between measured and 16 -
computed discharges using six different methods. ©
14 • • R
• •
discharge over the compound sharp-crested b 12 -
weir, the gradients obtained from the graphs of *
o
computed discharge versus actual discharge for m
§ 8 -
each double 'V notch combinations are taken
9
into consideration. The gradient reaches one I 6-

when the method is more accurate. The variance 4 •

m «» 5 g
of the gradients with one is calculated by using
2 » " 1 * *
the Eq.(8). i I «
0 •
1 2 3 4 5 6 7 8
Compound Weir type
V=- (8)
(H-1) o Mtd n • Mtd 2i A Mtd Si x Mtd «! x Mtd a o Mtd 6i

Figure 7. The average percentage errors between

Where, V is the variance with 1 and y is the measured and computed discharges for different
gradient of the measured versus computed methods
discharge graph for a specific method in each
combination and n is the number of test runs.
The average percentage error (E) between the 19 - /
actual and computed discharges is also
computed using Eq.(9). /
§.
0.03835
E?
ro n .
/'
o
VI
b
/
o
1. jft
O

o. /
0.00309 • 0.00307 II 0.00415
n- /
0 2 4 6 8 10 12 14
Measured Discharge (L/s)
Mtd CD Mtd 2 Mtd 3 Mtd * Mtd 5J Mtd Q
Figure 8. Comparison between measured and
Figure 6. The variance of the gradients with methods computed discharges using method-3
of computing discharges

ENGINEER 36
5.3 Accuracy of discharge measurements
The accuracy of flow measurements using
compound weirs, having a 60° lower notch angle Where,
is compared with the accuracy of flow 2.5
measurements by a single 'V notch of 60°. The (11)
percentage error that can be expected in flow
measurements is computed according to Eq.(lO) So, when there is a requirement to measure a
based on the accuracy of the point gauge used wide range of flows accurately with reasonable
for head measurements which is 0.0508 mm. sensitivity, the above compound sharp-crested
weir can be selected due to its simplicity, easy
maintenance and good flow measurement
2fi(A) precision.

Where, the function Q(H) is taken according to Figures 10, 11 and 12 illustrate the final
the Method-3 and the variation of accuracy with discharge coefficients (Cdc) for different heads
head over the weir is shown in Figure 9. As can above the weir for various combinations of 'V
be seen in the figure, the accuracy of flow notches tested during this study. These curves
measurements using compound weirs with can be used to obtain a correct discharge
double 'V notches whose lower triangle is coefficient depending on the combination of 'V
having a notch angle of 60° is almost the same as notches in sharp-crested compound weirs.
the accuracy with a single 'V notch of 60°.
1.25 -
0.18-|
1.15 -
0.16 - 1.05
0.14- 0.95 -]
0.12 - •8 0.85
0.10- O
0.75
0.08 0.65 -
0.06 0.55 -
0.04- 0.45 -
0.02- 0.35
0.00 0.1 0.15 0.2 0.25 0.3
500 1000 1500 2000 h(m)

head over the w eir/(mm) Figure 10. Cd values for compound weirs having 60°
-60- - 60/150 60/120 60/90 lower notch angle & 10 cm lower weir height
Figure 9. Variation of percentage error with head over
the weir

0.85-|
6. Summary and Conclusions
0.75-
A compound sharp-crested weir composed of
two triangular parts with different notch angles 0.65- 150°
has been analysed and experimentally validated J

to provide accurate measurements for a wide ' 0.55-

rage of flow without discontinuity. The most
0.45
suitable method to estimate the flow over the
double 'V notch compound sharp-crested weir 0.35
in partially contracted flow conditions, is found 0.15 0.2 0.25 0.3
h(m)
to be the procedure given in Method-3. Here, the
intersection triangle is in the upper 'V notch Figure 11. Cd values for compound weirs having 60°
and the Cd of that part is taken as the discharge lower notch angle & 15 cm lower weir height
coefficient of the upper 'V notch and the
discharge can be computed using the Eq. 6. This
equation can be simplified in the form of;

37 ENGINEER
 1.45- 5. Brater, E.F., King, H.W., Lindell, J.E., and Wei,
C.Y. (1996) "Handbook of Hydraulics", Mcgraw-
1.35-
Hill, New York.
1.25 150°
01.15 6. British Standards Institution (BSI). (1965). "Thin
0"1.05- plate weirs and venture flumes in methods of
0.95- measurement of liquid flow in open channel",
0.85- 120°
Part 4A, BSI 3680, London.
0.75 7. Chow, V.T. (1959) "Open channel Hydraulics",
0.65 Mcgraw-Hill, New York.
0.1 0.15 0.2 0.25 0.3
h(m)
8. Henderson, EM. (1966) "Open channel flow"
Prentice-Hall, Englewood Cliffs, N.J.
Figure 12. Cd values for compound weirs having 90"
lower notch angle & 10 cm lower weir height 9. Kindswater, C.E., and Carter, R.W. (1959)
"Discharge characteristics of rectangular thin
plate weirs", Trans. American Society of Civil
Engineering, Vol. 124, pp.772-822.
References 10. Martinez, J., Reca, J., Morillas, M.T., and Lopez,
1. Abdel-Azim, M.N., Al-Brahim, A.M., and J.G (2005) "Design and calibration of a
Alhamid, A.A (2002). "Combined free flow over compound sharp-crested weir", Journal of
weirs and below gates", Journal of Hydraulic Hydraulic Engineering, Vol. 131, No. 2, pp.112-
Research, Vol.40(3), pp.359-365. 116.

2. Aydin, I., Metin Ger, A., and Hincal, o. (2002) 11. Swamee, P.K., qha, C.S.P., and Kumar, S. (1998)
"Measurement of small discharges in open "Discharge equation for rectangular slots",
channels by slit weir", Journal of Hydraulic Journal of Hydraulic Engineering, Vol. 124(9),
Engineering, Vol.l28(2), pp.234-237. pp.973-974.

3. Borghei, S.M., Jalili, M.R., and Ghodsian, M. 12. LMNO Engineering Research and Software Ltd.
(1999) "Discharge coefficient for sharp-crested (1999) "Focus on open channel flow
side weir in subcritical flow", Journal of measurement: V-notch weirs" Newsletter, Vol. 1,
Hydraulic Engineering, Vol.125 (10), pp.1051- Athens, Ohio.
1056. 13. United States Department of the Interior, Bureau
4. Bos, M.G. (1989) "Discharge measurement of Reclamation (USER). (1997), Water
structures", International Institute for land measurement manual, 3rd Ed., Denver.
Reclamation and Improvement (ILRI),
publication 20, Wageningen, The Netherlands.

ENGINEER 38