OWNER’S MANUAL

SUPPLEMENT
Jet Drive Outboard
BF60J / 40 Jet
BF90J / 65 Jet

Before operating your jet drive outboard for the first time,
please read this Owner’s Manual. Even if you have operated
other jet driven outboards, take time to become familiar with
how this jet drive outboard works and practice in a safe area
until you build up your skills.

CONTENTS
WELCOME................................................ 2 SERVICING YOUR JET DRIVE .............. 5 TROUBLESHOOTING............................ 19
FOR YOUR SAFETY ................................ 2 Maintenance Safety........................... 5 Poor performance ............................. 19
THEORY OF OPERATION........................ 2 Maintenance Schedule ...................... 5 Outboard propels while in neutral ..... 19
SIZING & APPLICATIONS ........................ 3 General Inspection ............................ 6 TECHNICAL INFORMATION.................. 19
Selecting a Boat and Hull.................... 3 Bearing Lubrication............................ 6 Serial Number Location .................... 19
Selecting an Outboard Motor .............. 4 Reverse Gate Linkage....................... 6 CUSTOMER INFORMATION.................. 20
OPERATION ............................................. 4 Salt Water Use................................... 6 Register Your Jet Drive Outboard..... 20
Before Using Your Jet Drive Outboard 4 Impeller.............................................. 6 Parts and Service Items.................... 20
Steering ............................................... 4 Shear Key Replacement.................... 7 Dealer Locator Information ............... 20
Operating in Shallow Water ................ 4 JET DRIVE ASSEMBLY .......................... 8 How to Contact Honda...................... 20
Intake Blockage................................... 4 BF60J / 40 Jet ................................... 8 Honda Publications........................... 20
Mooring ............................................... 4 BF90J / 65 Jet ................................. 12 Frequently Asked Questions............. 20
Throttle Control ................................... 5 INSTALLATION & RIGGING.................. 16 DISTRIBUTOR’S LIMITED WARRANTY 21
Reducing Spray and Cavitation........... 5 Remote Controls.............................. 16 EMISSION CONTROL SYSTEM
Tiller Controls................................... 17 WARRANTY ........................................... 23
Outboard Mounting.......................... 19 TILLER HANDLE TEMPLATES .............. 25

QUESTIONS?
Contact your Honda dealer.
There is a dealer locator at
marine.honda.com
00X31ZZ3 6201S
© 2017-2018 American Honda Motor Co., Inc. All Rights Reserved
WELCOME
 WARNING
Congratulations on your selection of a Honda jet drive outboard The engine exhaust from this product contains
motor! We are certain you will be pleased with your purchase of one chemicals known to the State of California to cause
of the finest jet driven outboards on the market. We want to help you cancer, birth defects, or other reproductive harm.
get the best results from your new jet drive outboard and to operate it
safely. This manual contains information on how to do that for only the
jet drive portion of your outboard; please read it carefully. Use this
owner’s manual supplement in conjunction with the Honda Marine THEORY OF OPERATION
BF60A or BF90D owner’s manual supplied with the outboard motor’s
powerhead. Jet driven outboards were designed to allow boats to operate in very
When your jet driven outboard needs scheduled maintenance, keep in shallow water such as creeks, rivers, or other waterways that are
mind that Honda Marine servicing dealership personnel are specially inaccessible to normal propeller-driven boats.
trained in servicing Honda outboards and are supported by the parts A jet driven outboard works by drawing water into the jet drive unit by
and service divisions of American Honda. an impeller that is driven directly by the engine’s driveshaft. This water
Please read the DISTRIBUTOR’S LIMITED WARRANTY on page 21, is then forced at high pressure and volume through a nozzle directed
and the EMISSION CONTROL SYSTEM WARRANTY on page 23 to astern of the boat. The velocity imparted to this mass of water creates
fully understand what is covered by warranty and your responsibilities an opposite force, and drives the boat forward.
of ownership.

FOR YOUR SAFETY

Your safety and the safety of others are very important. We have
provided important safety messages in this manual. This information
alerts you to potential hazards that could hurt you or others. Please
read these messages carefully.
Of course, it is not practical or possible to warn you about all the FORWARD GEAR
hazards associated with operating or maintaining an outboard motor. The reverse gate is in
You must use your own good judgment. the down position.

Safety Instructions To drive the boat backward, the operator shifts the outboard into
reverse causing a curved mechanical gate to move into the stream of
You will find important safety information in a variety of forms: water that exits the nozzle. This gate redirects the water into the
• Instructions – how to use this outboard correctly and safely opposite direction, and the thrust of the redirected water propels the
• Safety Messages – preceded by a safety alert  symbol and one
boat backward.

of three signal words: DANGER, WARNING, or CAUTION.

Each message tells you what the hazard is, what can happen, and
what you can do to avoid or reduce injury.
These signal words mean:

DANGER You WILL be KILLED or SERIOUSLY

HURT if you don’t follow instructions.

WARNING You CAN be KILLED or SERIOUSLY

HURT if you don’t follow instructions. REVERSE GEAR
The reverse gate is in
the up position.
 CAUTION You CAN be HURT if you don’t follow
instructions.

• Damage Prevention Messages – you will also see other important

messages that are preceded by the word NOTICE. This word
means:

Your engine, property, or the environment can be

NOTICE
damaged if you don’t follow instructions.

2
 Hull Tunnels
SIZING & APPLICATIONS A properly designed tunnel, combined with a slight vee bottom hull
can greatly enhance jet boat performance. It should raise the motor
two to three inches, and place the heel of the jet intake flush or slightly
Selecting a Boat and Hull above the bottom of the boat.
Combining the correct outboard power and boat design is the secret A jet tunnel does not work well with a flat bottom boat due to the air
of successfully using an outboard jet to run in shallow water. The most ingestion! It’s imperative that the hull is designed correctly with the
important part is selecting the boat. Choose a boat that is as light as tunnel for the boat to operate properly.
possible. Unlike a propeller drive, you cannot change to a lower pitch The top of the tunnel width should be about 1-3/4 times the width of
jet drive impeller to increase load capacity. the jet drive water intake. The tunnel length does not have to be
Aluminum is usually the material of choice for a jet driven boat. It is longer than approximately 2-1/2 times the water intake width.
light, tough, and easy to form in the proper configuration. For outboard
jets, the bottom thickness can range from 1/16 in (1.6 mm) for 20 to
50 hp applications to 3/16 in (4.8 mm) for motors up to 225 hp. The
thinner gauge is more easily damaged whereas the thickest gauge
can be a weight problem on midrange power from 50 - 100 hp motors.
Aluminum boats are preferred because they usually have optimum
hull designs, while being durable and lightweight.
The size and shape of the bottom of the boat is very important. The
object is to ride on top of the water, which requires a good planing TUNNEL
surface, and to float as shallow as possible when shut down.
The bottom of the boat should be at least 48 inches wide, and the
Chines and Keels
centerline of the boat length should be at least 13 feet long. 6° to 9° The chines of a boat are where the boat’s sides meet the bottom. The
degrees of deadrise is good. Air entering the jet drive causes chines should be sharp angles. Round chines tend to suck the boat
slippage, so the boat bottom needs to supply solid water (free of air) down in the water and cause drag.
to the jet drive intake.
No one boat can satisfy every need, so choices must be made. With
this in mind, some pros and cons of various boat types and
characteristics are listed below.

Inflatables
Inflatables are light, easy to transport, and bounce off rocks nicely.
However, due to the flexible nature of their bottom, they trap and
introduce air into the jet intake. Steering can be unpredictable or SHARP ANGLED
inconsistent when running light and while in crosswinds. CHINE

A rigid hull inflatable, on the other hand, cannot be folded to fit inside
your car but steers better and provides solid water to the intake.
Unfortunately, most rigid inflatable hulls that are currently available
have more than 10° of deadrise.

Pontoon Boats
Pontoon boats do not provide a defined height apron of water ahead
ROUNDED
of the jet intake. The water level between the pontoons varies with
CHINE
speed and load carried. It is necessary to build an inclined plane
ahead of the jet intake attached to the motor mount, that is
approximately 16 inches wide, and inclined approximately 15° with the Keels can be a problem by introducing air into the jet intake. Center
leading edge above the water level when the boat is fully loaded at keels vary in size and may introduce air. If this is suspected, the keel
rest. The trailing edge should be lined up with the leading edge of the should stop two to three feet forward of the transom. Other keel
jet intake. arrangements which tend to funnel air to the jet intake should be
avoided.
Flat Bottom Boats
A flat bottom boat runs shallower than a vee bottom boat, but slides
on the turns more. A vee bottom splits off air bubbles before they
reach the jet intake. A flat bottom carries bubbles straight back.

Vee Hulls
A shallow vee of 6° to 10° of deadrise will enhance jet boat handling. APPROX.
2 - 3 FT
A deep vee or multi-vee design is not desirable for a jet drive
outboard, not just because of the increased draft and drag, but
because the jet drive outboard needs a flat apron of water about 10
inches wide leaving the hull on which to set the leading edge of the jet KEEL
intake, to minimize air intake and frontal drag. The deadrise should be
fairly constant and not increase to a deep forefoot at the bow. A deep
forefoot can cause a boat to spin out on a sharp turn.
3
Selecting an Outboard Motor may wish to run down and back up the same stretch to memorize the
course you take.
A boat operating at slow speed requires considerably more water
depth than one that is planing on the surface of the water. Therefore, it If you are not sure of a tight area on a downstream run, it is better to
is important to use sufficient horsepower and not to overload your drift through on the oars with the outboard motor tipped up, or else
boat beyond its ability to plane. The following table shows the amount line the boat through on a rope.
of horsepower that is needed in relation to the gross weight of the
boat. This information is based on experience gathered with sled-type Operating in Shallow Water
boats powered by jet driven outboards. Gross weights shown include
The life of the impeller and water intake can be greatly increased by
the boat, motor, passengers, fuel, and gear.
avoiding the intake of sand and gravel. The intake suction, acting on
240 the river bottom, will act like a dredge when the intake comes within
220 two or three inches of the bottom. It is best to shut off the outboard
200
motor and drift up to the beach when landing, and to shove off with an
oar when leaving the beach. You can idle through areas less than one
180
foot deep, but there should be more than one foot of water under the
MOTOR HORSEPOWER

160 boat when opening the throttle to reach a plane.

140 Once planing, the boat speed will prevent sucking in gravel. The
120 suction is still acting, but the water intake passes over the river bottom
100
so quickly that the boat is gone before the rocks have time to lift off
the bottom.
80
To run in a shallow area, pay attention to the river conditions and what
60
the river bottom is made up of, decide your course, and then if you
40 feel safe, run through on a full plane. The faster you go, the higher the
20 boat will ride. Be sure you know the river’s bottom before attempting
0
to go through on a full plane.
500

1800
2000

2400
2600

3000
3200

3600
3800
4000
600
800

1200
1400
1600

2200

2800

3400
1000

This should pose no problems if the river bed is sand and gravel. If
you end up running high and dry, shut off the outboard motor
GROSS WEIGHT - LBS.
immediately and drag the boat off to deeper water. However, if the
NOTE: The performance of jet driven outboards do not reflect the true river bed is full of sharp, larger rocks, you run the risk of damaging
performance of the same outboard motor that is driven by a propeller. your hull, injuring yourself, and potentially walking home.
On average, a jet driven outboard produces approximately 70% of the Gravel passing through the pump will round over the leading edge of
power of the same outboard motor that is propeller driven. the impeller blades. For maximum performance, file these edges
occasionally to keep them sharp as when new.

OPERATION Occasionally, on running aground, a small rock will jam between the
impeller and the intake wall, and the outboard motor will come to a
stop. Neither the starter motor or starter rope will be able to turn over
The following sections will provide important information and tips on the motor. To free the small rock, remove the six lock nuts attaching
how to get the most out of your jet driven outboard. the water intake, and then free the rock or obstruction that is wedged
between the impeller and housing.
Before Using Your Jet Drive Outboard Your jet drive is equipped with a shear key to protect the unit in the
All outboard motor operators must read the following sections: event of a rock jam. See page 7 for shear key replacement.
• FOR YOUR SAFETY (page 2)
Intake Blockage
• OPERATION (page 4)
Occasionally, when either holding or proceeding slowly upstream in a
• SERVICING YOUR JET DRIVE (page 5) fast moving shallow area, you will lose power. This is usually caused
by suction holding larger flat rocks, lily pads, or debris against the
Steering intake grille and restricting the water intake. This problem can be
Experiment with steering your boat in an open area before attempting resolved by quickly stopping the motor and then restarting it, the rocks
downstream river running. You will find quick response to the helm, or debris will fall away from the water intake and full power will be
but due to the relatively flat bottom hulls and lack of propeller keg, restored.
your boat will tend to skid on the turns. You must start your turns early However, if a rock or debris is jammed in between the intake grille
and use sufficient power to maintain steerage. If you attempt to turn bars, it must be removed by prying it out of the grille with an
too tight at too high of a speed, your boat will likely spin out. This is a appropriate tool, such as a screwdriver.
great way to stop in a hurry but is not recommended because it can
cause an unstable boat to roll over.
Mooring
Running upstream is the easiest. Remember that when running If your boat is tied up by the seashore where the action of surf causes
downstream, your speed relative to the shore is the speed of the river the boat to rise and fall on the sandy beach, be sure to tilt the
added to your boat speed. outboard motor up and out of the water. If the motor is kept in the
When running upstream, your speed relative to the shore is the speed operating position, the wave action of the surf can deposit enough
of your boat minus the speed of the river. You can throttle back and sand into the jet pump that the outboard motor cannot be cranked. If
pick your way up through tight areas with good control. At that time, this happens, the jet pump will not be damaged, but it will need to be
you should stop and study the layout looking downstream, so that you washed out before attempting to start the motor.
will recognize it on the return, downstream run. Once through, you
4
Throttle Control Maintenance Safety
As with any outboard, you will get maximum mileage by not running at Some of the most important safety precautions follow. However, we
full throttle. You should also not run at one third to half throttle with the cannot warn you of every conceivable hazard that can arise in
boat at a steep angle, which leaves a large wake and wastes fuel. performing maintenance. Only you can decide whether or not you
should perform a given task.
Run at a slow idle speed for trolling and moving cautiously in
uncharted areas. Running at half speed and a steep angle is the most
vulnerable position for hull damage with submerged obstructions.  WARNING
For cruising, run at the least throttle that will maintain an easy plane Improper maintenance can cause an unsafe condition.
(not a sluggish one). Go to full throttle only when necessary for
Failure to properly follow maintenance instructions and
minimum draft, climbing steep drop offs, or starting a heavy load. precautions can cause you to be seriously hurt or killed.
When planing easily, you will slide over most any obstruction that is Always follow the procedures and precautions in this
just below the water surface, out of sight, and not leave a telltale manual.
disturbance on the surface of the water.
Safety Precautions
Reducing Spray and Cavitation Make sure the engine is off before you begin any maintenance or
An intake fin kit is available to reduce cavitation when running with the repairs. This will eliminate several potential hazards:
wind in a chop. The intake fin kit attaches to the intake assembly and • Carbon monoxide poisoning from engine exhaust
directs more water into the impeller. To purchase the intake fin kit, Be sure there is adequate ventilation whenever you operate
contact an authorized Honda Marine dealer. the engine.
To further reduce spray, or reduce cavitation in rough water, a 1/32” • Burns from hot parts
thick galvanized splash plate can be used. This will allow mounting Let the engine and exhaust system cool before touching.
the motor higher to reduce drag. This splash plate must be custom • Injury from moving parts
fabricated for an individual boat and fastened to the hull using a Do not run the engine unless instructed to do so.
wooden block and screws. Since the splash plate must be built for a
specific boat and hull, it is not available off-the-shelf through a Honda Read the instructions before you begin, and make sure you have the
Marine dealer. Contact an authorized Honda Marine dealer for more tools and skills required.
information. To reduce the possibility of fire or explosion, be careful when working
around gasoline. Use only a nonflammable solvent, not gasoline, to
clean parts. Keep cigarettes, sparks, and flames away from all
WOODEN
BLOCK
fuel-related parts.

Maintenance Schedule
INTAKE
FIN KIT
Item1 Interval Page

General Inspection • Inspect the jet drive unit’s

page 6
hardware occasionally
SPLASH PLATE
Bearing Lubrication • Lubricate the bearing after
each use or every 10 hours
• Every 30 to 40 hours, pump page 6
SERVICING YOUR JET DRIVE additional grease through the
bearing to purge any moisture

Proper maintenance is essential for safe, economical, and Reverse Gate • Occasionally inspect the
trouble-free operation. Linkage reverse gate’s operation and page 6
hardware
 WARNING Salt Water Use • Occasionally inspect hardware
for corrosion or salt buildup
Improper maintenance, or failure to correct a problem
before operation, can cause a serious malfunction. • Remove and reinstall all page 6
hardware every year to prevent
Some malfunctions can seriously hurt or kill you. it from seizing, corroding, or
Always follow the inspection and maintenance rusting2
procedures in this owner’s manual.
Impeller • Occasionally inspect the
page 6
impeller for wear or damage2
To help you properly care for your jet driven outboard, the following
pages include simple maintenance and inspection procedures using 1: For commercial use, log hours of operation to determine the proper
basic hand tools. Other service tasks that are more difficult or require maintenance intervals
special tools are best handled by professionals and are normally
2: This item should be serviced by an authorized Honda Marine
performed by a Honda Marine technician or other qualified mechanic.
servicing dealer unless you have the proper tools and are
Remember that an authorized Honda Marine servicing dealer knows mechanically proficient.
your outboard best and is fully equipped to maintain and repair it. To
Failure to follow this maintenance schedule could result in
ensure the best quality and reliability, use only new, Honda Genuine
non-warrantable failures.
parts or their equivalents for repair and replacement.
5
General Inspection Salt Water Use
Check all mounting bolts, screws, and linkage connections Aluminum and stainless steel have been used in the construction of
occasionally to be sure they are tight. your jet drive. These materials have either been treated or are
inherently resistant to corrosion. When not in use, it is recommended
Bearing Lubrication that the outboard motor should be tilted up so the jet unit is out of the
water.
Grease the bearing every 10 hours.
When used in salt water more than fresh water, remove the mounting
A tube of grease is supplied with your jet drive. Make greasing a part hardware, clean and regrease, and then reassemble once per year.
of your cleanup after the day’s use. Failure to do so may result in hardware that is difficult, if not
Disconnect the lube hose from the zerk grease fitting, and then pump impossible, to remove at a later date.
in just enough grease to replace the grease that is already in the lube
hose, Reconnect the lube hose coupling to the zerk grease fitting. Impeller
Every 30 to 40 hours, pump in extra grease to purge any moisture
from the bearing. The texture of the grease coming out gives an
Inspection
indication of conditions inside the bearing housing. A gradual increase Occasionally, inspect the impeller’s leading edges and the impeller
in moisture content over time indicates seal wear. clearance using the following Leading Edge Inspection and Impeller
Clearance procedures.
If the grease begins to turn a dark, dirty gray, the bearing and seals
should be inspected, and replaced if necessary. Some discoloration of Remove the intake assembly and flanged liner to gain access to the
the grease is normal during the break-in period when the bearing and impeller, as shown below. Installation of the intake assembly and
seals are new. flanged liner is the reverse order of removal. Add water-resistant
marine grease to the stud threads before reinstalling the 5/16”-18 lock
nuts.

ZERK FITTING

FLANGED
LINER
5/16”-18
LOCK NUT (6)
INTAKE
ASSEMBLY
LUBE HOSE

Reverse Gate Linkage Leading Edge Inspection

Occasionally, check the adjustment of the reverse gate linkage. In Inspect the impeller for damage
FORWARD, the gate should be firmly locked in position. Pull on the or rounded leading edges that are
gate to verify that it does not move. This will prevent wave action from be caused by the ingestion of
accidentally shifting the gate into reverse as the boat is violently gravel. For maximum
maneuvered. performance, file the impeller’s IMPELLER
The roller should be at the end of the slot in the cam so that the gate leading edges to keep them as LEADING
cannot be forcibly rotated toward reverse. Do not be concerned if the sharp as when new. EDGES
gate does not fully close in the reverse position, as water pressure will 1. File along the slope on the
close it. ROUNDED EDGE
upper side of the blades.
If improperly adjusted, the reverse gate can be tripped into reverse 2. File along the underside of
when not expected, and will cause the outboard motor to kick up out each blade until the leading
of the water. edge is 1/32”
REVERSE (0.79 mm). Do not bevel the
CAM SLOT leading edge of the blades to
create a knife-like edge. FILE

3. Blend the underside of the

blade in a gentle curve.
FORWARD FILE
CAM SLOT Rough edges on the impeller can
cause decreased performance
1/32”
and cavitation. Cavitation occurs
REVERSE (0.79 mm)
in low pressure areas around the
GATE
rough edges of the impeller
blades, and can cause small
pockets of water to boil, which CURVE
creates steam. The small pockets
of steam will then collapse and release a large amount of energy that
prematurely erodes the impeller.
6
Impeller Clearance Shear Key Replacement
As the impeller wears during normal usage, Your jet driven outboard is equipped with a shear key to
the clearance between the impeller and the protect the components in the event of a rock jamming
flanged liner becomes larger. in between the impeller and the intake housing.
For optimal performance, the impeller The shear key can be removed and replaced by
clearance should be 1/32” (0.79 mm). Use following the procedure below. Note the number and
a feeler gauge to measure the gap positions of the impeller shim washers relative to the
between the impeller blades and the impeller, and replace them in the same order.
flanged liner. Hold the flanged liner in place
while measuring. Be sure to measure the If you experience difficulty removing the impeller, it is
gap for all three blades before determining most likely due to the shear key being wedged against
the impeller clearance. the side of the driveshaft.

Remove the brass nut, nut keeper, cup, 1. Remove the intake assembly and flanged liner by loosening the
IMPELLER six 5/16”-18 lock nuts.
and urethane washers, impeller shims, and SHIMS (7)
the impeller. Stack additional shims onto
the top side of the impeller until the impeller
clearance has been corrected. Place any
remaining shims on the bottom side of the
impeller. FLANGED
LINER
Once there are no shims left underneath the impeller and the impeller 5/16”-18
clearance is still excessive, replacement of the impeller will be LOCK NUT (6)
required. INTAKE
ASSEMBLY

GAP FLANGED
LINER

2. Remove the following:

• Brass nut
• Nut keeper
IMPELLER
• Cup
• Urethane washers (2)
• Impeller shims
• Impeller
IMPELLER SHIMS
GAP
URETHANE
WASHERS
GAP
CUP

NUT KEEPER

The flanged liner may have gouging from gravel. This is normal, and BRASS NUT
there is considerable surface on the liner for wear. If the impeller has
been replaced and the blade clearance is still more than 1/32” (0.79
mm) with all seven shims beneath the impeller, the flanged liner may 3. Remove the shear key from the impeller.
need to be replaced.
Be sure to grease the driveshaft mating surface, the shear key,
sleeve, and driveshaft threads during reassembly. See the SHEAR KEY
appropriate assembly section (BF60J / 40 Jet: page 11,
BF90J / 65 Jet: page 15) for impeller installation.

IMPELLER

4. Replace the shear key and then reinstall the impeller, flanged
liner, and intake assembly in the reverse order of removal. Refer
to the appropriate assembly section for more detail (BF60J / 40
Jet: page 11, BF90J / 65 Jet: page 15).

7
 Parts Diagram
JET DRIVE ASSEMBLY
6
BF60J / 40 Jet
List of Parts
The jet drive unit comes partially assembled. The items listed in the
table below are the assemblies and individual parts that are included
in the jet drive unit’s box.
A genuine Honda BF60AK1 water pump kit (P/N 06193-ZZ3-010) is 30
supplied with the jet drive unit and should be installed during
assembly.
29
For a complete list of individual parts for the jet drive unit, refer to the
information found in the Parts Catalog (page 20).

Ref. Item Qty. 1

1 Main housing assembly 1 2
2 Driveshaft assembly 1
3 Impeller 1
4 Flanged liner 1
5 Intake assembly 1
6 Neutral cable assembly (for remote controls) 1 9 10 11 3
8
7 6 x 10 mm dowel pin 3
8 Exhaust baffle 2
9 10-24 x 3/4” bolt 2 7 12
10 10-24 lock nut 2 17

11 Lock washer, #10 2 4

12 Shift guide 1
13 10 x 60 mm hex bolt 2
24
14 10 x 70 mm hex bolt 1 23
5
22
15 10 x 90 mm hex bolt 1
16 10 mm lock washer 4
17 Sleeve shaft (plastic) 2
18 Shear key 2
19 Shim washers 7 18 27

20 Nut keeper 2
21 3/4”-16 shaft nut (brass) 1 28

22 Wedge stud 1 14
20
13
23 Wedge bolt 1
24 5/16”-18 lock nut 7 15 25

25 5/16”-18 x 1” hex bolt 4

26 5/16” lock washer 4
27 Cup (torsional damper) 1 21
28 Urethane washer (torsional damper) 2 26
16
29 Grease, tube 1
19
30 Honda water pump kit (P/N 06193-ZZ3-010) 1

8
Assembly c. Remove the rubber pump impeller from the pump liner, if it is
1. Secure the engine on a stand or on the boat’s transom so that it is not already separated.
mounted vertically.
2. Install the jet drive driveshaft assembly into the main housing
using the four 5/16”-18 x 1” hex bolts and four 5/16” lock
washers, in the orientation where the three small O-rings on the
driveshaft align with the three small grease holes in the main
housing. Grease the bolt threads prior to installation, and then
tighten to the specified torque. PUMP RUBBER
TORQUE: 15 lbf-ft (20 N•m) LINER IMPELLER

d. Apply water resistant marine grease to the circumference of a

new water pump O-ring, and then install it into the impeller
housing.
GREASE Install the pump liner into the pump housing by aligning the
HOLES
projection on the pump liner with the cavity inside the pump
housing.
Apply water resistant marine grease to the inner wall of the
pump liner.

PUMP
LINER
DRIVESHAFT O-RINGS
ASSEMBLY

5/16” LOCK
WASHER
WATER PROJECTION
5/16”-18 x 1” BOLT PUMP
O-RING
3. Install the water pump assembly onto the main housing using the
following procedure: CAVITY

a. Insert the two 6 x 10 mm dowel pins into the main housing.

6 x 10 mm e. Set the water pump woodruff key in the flat area on the
DOWLEL PIN (2) driveshaft, and then slide the rubber pump impeller down the
driveshaft and align the notch in the impeller with the
woodruff key.
WOODRUFF RUBBER
KEY IMPELLER

b. Place the water pump gasket onto the main housing, and
then place the stainless steel plate on top of the water pump
gasket.

f. Install the impeller housing assembly by sliding it down over

STAINLESS the driveshaft. Rotate the driveshaft clockwise when mating
STEEL PLATE the impeller housing assembly around the rubber impeller
and onto the stainless steel plate. Doing this will set the
rubber impeller fins in the correct direction.
WATER PUMP
GASKET
IMPELLER DRIVESHAFT
HOUSING

9
 g. Place the water tube seal and seal holder onto the impeller 6. Attach the jet drive to the extension case using the following
housing, and then install the four 8 x 40 mm bolts, and two procedure.
8 mm washers. Grease the bolt threads, and then tighten to a. Install the plastic shift rod guide into the 5/16” hole, and the
the specified torque. 6 x 10 mm dowel pin into the rear hole on the main housing to
TORQUE: 15 lbf-ft (20 N•m) align the jet drive to the motor extension case.
8 x 40 mm BOLTS WATER SHIFT ROD 6 x 10 mm DOWEL PIN
AND WASHERS TUBE SEAL GUIDE
HOLDER

8 x 40 mm
BOLTS

4. In the mid section of the motor, there is a curved opening in the b. Use the four M10 bolts and lock washers to secure the jet
rib between the exhaust gas and the cooling water passages. drive assembly to the extension case. Grease the bolt
This opening must be blocked to control exhaust noise. Slide the threads, driveshaft splines, and rubber water tube seal prior
exhaust baffle onto the rib, flush with the mounting face. Install to guiding the jet drive into place. The 10 x 60 mm bolts
the 10-24 x 3/4” bolts, washers, and lock nuts. Make sure the should be installed in the holes at the front end of the main
10-24 lock nuts are facing toward the rear of the extension case housing. The 10 x 70 mm bolt should be installed in the
as shown. Do not overtighten the nuts to avoid excessively port-side rear hole. The 10 x 90 mm bolt should be installed
distorting the plates. in the starboard-side rear hole.
TORQUE: 21 lbf-ft (29 N•m)

10-24 LOCK
NUTS
10-24 x 3/4”
BOLTS AND
LOCK
WASHERS

EXHAUST
BAFFLE

10 mm LOCK
WASHER (4) 10 x 90 mm BOLT
5. Install the tapered wedge stud at the rear of the outboard motor
extension case and tighten it securely. Grease the threads of the
wedge stud, and after tightening it, grease the tapered section.
10 x 60 mm 10 x 70 mm
TORQUE: 13 lbf-ft (18 N•m) BOLT (2) BOLT

7. Grease the threads and tapered section of the wedge bolt. Install
the wedge bolt through the 5/16” cross hole at the port-side rear
of the jet drive to capture the tapered wedge stud. Install a
5/16”-18 lock nut onto the wedge bolt studs and tighten to the
specified torque.
TORQUE: 7.0 lbf-ft (9.5 N•m)

WEDGE
STUD WEDGE
BOLT

10
8. Install the jet drive impeller. c. Fold the nut keeper tabs down against the brass nut to retain
a. Grease the vertical shaft threads, shear key, and impeller it. If the ears of the nut keeper do not line up with the flats on
bore. the brass nut, remove the brass nut, turn the nut keeper over,
and then retighten the brass nut.
Slide the shear key into the impeller bore slot, and then place
one plastic shaft sleeve inside the impeller bore. Align the slit
in the shaft sleeve with the shear key.

SHEAR KEY

SHAFT
SLEEVE

IMPELLER
NUT KEEPER TABS

9. Install the flanged liner and intake assembly in position with the
Hold the shear key in the slot in the impeller with your finger, lower end of the intake toward the rear. Grease the stud threads
and then slide the impeller onto the driveshaft. and tighten the six 5/16”-18 lock nuts to the specified torque. Do
not use lock washers.
TORQUE: 15 lbf-ft (20 N•m)

DRIVESHAFT

IMPELLER FLANGED
LINER

5/16”-18
LOCK NUT (6)
INTAKE
b. Install the seven shim washers, ASSEMBLY
one urethane washer, cup, one
nut keeper, and brass nut onto the
vertical shaft up against the
impeller and secure by hand.
Tighten the brass nut within the
specified torque range, until the 10. See “INSTALLATION & RIGGING” on page 16 for transom
ears of the nut keeper are aligned mounting and rigging instructions.
with the flats on the brass nut.
TORQUE:
4 – 22 lbf-ft (5 – 30 N•m)
Note:
Shims should not be placed above
the impeller on new installations
where no wear has occurred,
unless the blade clearance
exceeds 1/32”. Insufficient blade clearance will do more harm
than good from any performance gains it might provide.

11
BF90J / 65 Jet Parts Diagram

List of Parts
The jet drive unit comes partially assembled. The items listed in the
table below are the assemblies and individual parts that are included 6
in the jet drive unit’s box.
A genuine Honda BF90DK4 water pump kit (P/N 06193-ZY9-H00) is
supplied with the jet drive unit and should be installed during
assembly.
For a complete list of individual parts for the jet drive unit, refer to the
information found in the Parts Catalog (page 20). 29

Ref. Item Qty.

1 Main housing assembly 1 7

2 Driveshaft assembly 1

3 Impeller 1 1
2
4 Flanged liner 1

5 Intake assembly 1

6 Neutral cable assembly (for remote controls) 1

7 Water pump adapter 1

28
8 6 x 16 mm dowel pin 2 3
11
9 6 x 10 mm dowel pin 1
10 16
10 Shift guide 1
8
11 Front dowel 1 9

12 10 x 60 mm hex bolt 2 4

13 10 x 70 mm hex bolt 1

14 10 x 90 mm hex bolt 1
23
15 10 mm lock washer 4
22 21
16 Sleeve shaft (plastic) 1
5
17 Shear key 2

18 Shim washers 7

19 Nut keeper 2
17
20 3/4”-16 shaft nut (brass) 1

21 Wedge stud 1 26
27
22 Wedge bolt 1 13
12 19
23 5/16”-18 lock nut 7
24
24 5/16”-18 x 1” hex bolt 4
14
25 5/16” lock washer 4

26 Cup (torsional damper) 1

20
27 Urethane washer (torsional damper) 2
25
28 Grease, tube 1 15
18
29 Honda water pump kit (P/N 06193-ZY9-H00) 1

12
Assembly c. Install the impeller gasket B and then the stainless steel
1. Secure the engine on a stand or on the boat’s transom so that it is impeller cover on top of the aluminum adapter.
mounted vertically.
2. Install the jet drive driveshaft assembly into the main housing IMPELLER
using the four 5/16”-18 x 1” hex bolts and 5/16” lock washers, in COVER
the orientation where the two small O-rings on the driveshaft align
with the two small grease holes in the main housing. Grease the
bolt threads prior to installation, and then tighten to the specified
torque. IMPELLER
TORQUE: 15 lbf-ft (20 N•m) GASKET B

GREASE
HOLES

d. Remove the rubber pump impeller from the pump liner, if it is

not already separated.

DRIVESHAFT O-RINGS
ASSEMBLY

5/16” LOCK
WASHER PUMP RUBBER
LINER IMPELLER
5/16”-18 x 1” BOLT

3. Install the water pump assembly onto the main housing using the e. Apply water resistant marine grease to the circumference of a
following procedure: new water pump O-ring, and then install it into the impeller
housing.
a. Place the water pump gasket and 5/8” thick aluminum
adapter on top of the main housing by sliding it down over the
top of the driveshaft, in the orientation shown. The side of the IMPELLER
adapter with the two dowel pin holes should face UP, in the HOUSING
position shown.

ALUMINUM
ADAPTER
WATER PUMP
GAKSET
WATER PUMP
O-RING

f. Install the pump liner into the pump housing by aligning the
projections on the pump liner with the cavities inside the
pump housing.
Apply water resistant marine grease to the inner wall of the
pump liner.

PUMP LINER PROJECTION CAVITY

b. Insert the two 6 x 16 mm dowel pins into the 5/8” thick
aluminum adapter.
6 x 16 mm
DOWLEL PIN (2)

Position the pump liner in

the orientation shown.

13
 g. Set the water pump special key in the flat area on the 4. Install the tapered wedge stud at the rear of the outboard motor
driveshaft, and then slide the rubber pump impeller down the extension case. Grease the threads of the wedge stud, and after
driveshaft and align the notch in the impeller with the special tightening it, grease the tapered section.
key. TORQUE: 13 lbf-ft (18 N•m)
SPECIAL KEY RUBBER IMPELLER

h. Install the impeller housing assembly by sliding it down over WEDGE

the driveshaft. Rotate the driveshaft clockwise (when looking STUD
down over the main housing) when mating the impeller
housing assembly around the rubber impeller and onto the 5. Attach the jet drive to the extension case.
impeller cover. Doing this will set the rubber impeller fins in a. Install the front dowel into the 3/8” hole, the plastic shift rod
the correct direction. guide into the 5/16” hole, and a 6 x 16 mm dowel pin into the
rear hole to align the jet drive to the motor extension case.
SHIFT ROD 6 x 10 mm DOWEL PIN
GUIDE
DRIVESHAFT FRONT
IMPELLER
DOWEL
HOUSING

i. Install the four distance collars, 8 mm washers, and

8 x 40 mm bolts. Grease the bolt threads, and then tighten to b. Use the four M10 bolts and lock washers to secure jet drive
the specified torque. assembly to the extension case. Grease the bolt threads and
TORQUE: 15 lbf-ft (20 N•m) driveshaft splines prior to guiding the jet drive into place. The
Place the water tube seal ring into the impeller housing by 10 x 60 mm bolts should be installed in the holes at the front
aligning the projection on the seal with the hole in the end of the main housing. The 10 x 70 mm bolt should be
housing, and then grease the inner wall of the seal ring. installed in the port-side rear hole. The 10 x 90 mm bolt
should be installed in the starboard-side rear hole.
8 x 40 mm TORQUE: 21 lbf-ft (29 N•m)
BOLTS (4)

8 mm
WASHER (4)
WATER TUBE
SEAL RING COLLAR (4)

10 mm LOCK
WASHER (4) 10 x 90 mm
BOLT

10 x 60 mm
BOLT (2) 10 x 70 mm
BOLT

14
6. Grease the threads and tapered section of the wedge bolt. Install b. Install the seven shim washers, one
the wedge bolt through the 5/16” cross hole at the rear of the jet urethane washer, cup, one nut keeper,
drive to capture the taper lock stud. Install a 5/16-18 lock nut onto and brass nut onto the vertical shaft up
the wedge bolt studs and tighten to specified torque. against the impeller and secure by
TORQUE: 7.0 lbf-ft (9.5 N•m) hand. Tighten the brass nut within the
specified torque range, until the ears of
the nut keeper are aligned with the flats
on the brass nut.
TORQUE:
4 – 22 lbf-ft (5 – 30 N•m)
WEDGE
Note:
BOLT
Shims should not be placed above the
impeller on new installations where no
wear has occurred, unless the blade
clearance exceeds 1/32”. Insufficient
blade clearance will do more harm than
good from any performance gains it might provide.
c. Fold the washer retainer tabs down against the nut to retain
it. If the ears of the nut keeper do not line up with the flats on
7. Install the jet drive impeller onto the driveshaft. the brass nut, remove the nut, turn the nut keeper over, and
a. Grease the vertical shaft threads of the driveshaft, shear key, then retighten the brass nut.
and impeller bore.
Slide the shear key into the impeller bore slot, and then place
one plastic shaft sleeve inside the impeller bore. Align the slit
in the shaft sleeve with the shear key.

SHEAR KEY

SHAFT
SLEEVE
NUT KEEPER TABS
IMPELLER 8. Install the flanged liner and intake assembly in position with the
lower end of the intake toward the rear. Grease the stud threads
and tighten the six 5/16”-18 lock nuts to the specified torque. Do
Hold the shear key in the slot in the impeller with your finger, not use lock washers.
and then slide the impeller onto the driveshaft.
TORQUE: 15 lbf-ft (20 N•m)

DRIVESHAFT

FLANGED
LINER
IMPELLER 5/16”-18
LOCK NUT (6)
INTAKE
ASSEMBLY

9. See “INSTALLATION & RIGGING” on page 16 for transom

mounting and rigging instructions.

15
 Attach the neutral cable to the reverse gate linkage and onto the
INSTALLATION & RIGGING inner side of the cable anchor bracket. Adjust the neutral cable’s end
link so that the number of threads shown match the number of threads
shown on the shift cable’s end link. The neutral cable should act as an
extension of the shift cable.
Remote Controls
After the neutral cable is attached to the reverse gate linkage and to
If remote controls are used, a shift cable assembly and neutral cable
the inner side of the cable anchor bracket, it must be routed between
assembly (provided with the jet drive unit) will be used. The shift cable
the outboard motor and transom bracket and toward the port side of
is moved by the remote control box and operates the reverse gate.
the outboard. The neutral cable should then pass around the front of
The neutral cable operates forward, neutral, reverse, and neutral
the outboard, through the rigging grommet, and attached to the shift
safety switch functions inside the outboard motor.
link pin on the outboard.
The shift cable is attached to the cable anchor bracket and reverse
Move the shift link pin to the FORWARD direction.
gate linkage. This cable is routed over the transom and connects to
the remote control box. The neutral cable attaches to the reverse gate Adjust the shift pivot assembly/cable so that it easily slides over the
linkage and cable anchor bracket, and is routed between the outboard shift link pin without any help or force. It is very important that the
and transom bracket, around the front of the outboard, through the neutral cable is adjusted properly to ensure the neutral safety switch
cable grommet, and then attaches to the shift link pin. The neutral functions correctly.
cable must be routed this way to prevent kinking the cable.

SHIFT PIVOT
NEUTRAL CABLE ASSEMBLY

Route the cable as

shown.

LOCK
MECHANISM

SHIFT LINK PIN

SHIFT CABLE
Route the cable
over the transom to
the remote control SHIFT PIVOT
box. ASSEMBLY
REVERSE
GATE CABLE ANCHOR
BRACKET

NEUTRAL CABLE
REVERSE GATE
LINKAGE

With the remote control’s shift handle in forward, the reverse gate
linkage in forward, and the cam roller at the end of the slot, attach the
shift cable to the outer side of the reverse gate linkage on the jet
drive. Adjust the cable and/or cable anchor bracket position to this set
condition. Shift to reverse, and then back to forward. The roller should
be at the end of the cam slot so that the gate cannot be forcibly
rotated toward reverse. Pull on the gate by hand to verify this. If this
forward lock condition is not met, make the necessary adjustments to
the shift cable so that the reverse gate linkage positions are correct.
CABLE ANCHOR
NEUTRAL CABLE BRACKET

REVERSE GATE
LINKAGE

SHIFT CABLE

16
Tiller Controls A 17/64” hole must be drilled into the tiller’s shift handle to receive the
cable rod end. Start by filing a flat area on the handle at the drill hole
Tiller Handles with Troll Control location shown in the image below. Use a center punch to enable
Remove the lower cover plate from the tiller handle assembly. ease of drilling. Start by drilling a pilot hole using a 1/8” drill bit, then
follow with a 17/64” drill bit. Be careful to align the drill horizontally so
that it is perpendicular to the shift lever and square with the tiller
handle.
Screw the rod end onto the shift cable so that the end of the rod end
reaches 1/8” onto the unthreaded section of the cable. Insert the
90-degree rod end into the shift handle, and then install the 1/4"-28
nylon lock nut.

DRILL HOLE
LOCATION
LOWER
COVER
PLATE

Carefully cut out and align the drilling template (found on page 25) to
the tiller handle. Use masking tape to hold the template onto the tiller
handle in the location shown.
1/4”-28
DRILLING LOCK NUT
TEMPLATE ROD END

SHIFT CABLE

Attach the shift cable to the outer side of the cable anchor bracket.
Attach the lower end of the shift cable to the outer side of the reverse
gate linkage. The cable anchor bracket is slotted to allow for cable
alignment.

CABLE
ANCHOR
BRACKET
Use a center punch to mark the two hole
locations prior to drilling. Use a 7/32” drill bit
with a depth stopper, such as a piece of
rubber tube, set to a maximum of 3/8”. This is
necessary to prevent the drill bit from
protruding too deep and making contact with
any electrical wires when drilling the holes.
Attach the cable anchor bracket using two FORWARD
10-24 X 3/4” screws and nylon lock nuts. POSITION
Reinstall the lower tiller cover.

Move the shift handle into the forward position. Adjust the lower rod
end and cable anchor bracket so that the cam roller is all the way to
the bottom of the cam slot. Shift to reverse and back to forward to
verify this roller position. Pull on the reverse gate to verify that it is
CABLE locked in forward.
ANCHOR
BRACKET

10-24 x 3/4”
SCREWS

17
Tiller Handles without Troll Control Two 3/16” holes must be drilled into the tiller’s shift handle to receive
Remove the lower cover plate from the tiller handle assembly. the shift cable bracket. Carefully cut out and align the drilling template
(found on page 27). Use a center punch to enable ease of drilling.
Start by drilling a pilot hole using a 1/8” drill bit, then follow with a 3/16”
drill bit. Be careful to align the drill horizontally so that it is
perpendicular to the shift lever and square with the tiller handle.

DRILLING
TEMPLATE

LOWER COVER PLATE

Carefully cut out and align the drilling template (found on page 27) to
the tiller handle. Use masking tape to hold the template onto the tiller
handle in the location shown.

DRILLING
TEMPLATE
Attach the shift cable to the shift handle on the tiller handle by
inserting the two 10-32 x 1 1/2 screws through the shift cable bracket
and shift handle, as shown. Install two 10-32 lock nuts and tighten
them securely. Install the shift cable end link onto the shift cable
bracket and secure it with a 10-32 x 3/4” bolt and 10-32 lock nut.
SHIFT
10-32 LOCK
CABLE
NUT
10-32 x 1 1/2”
SCREW (2)
SHIFT CABLE
BRACKET
Use a center punch to mark the two hole
locations prior to drilling. Use a 7/32” drill bit
10-32 LOCK
with a depth stopper, such as a piece of
NUT (2)
rubber tube, set to a maximum of 3/8”. This is
necessary to prevent the drill bit from
10-32 x 3/4”
protruding too deep and making contact with
SCREW
any electrical wires when drilling the holes.
Attach the cable anchor bracket and shift
Attach the lower end of the shift cable to the outer side of the reverse
cable using two 10-32 X 1/2” screws and
gate linkage and cable anchor bracket. The cable anchor bracket is
10-32 lock nuts.
slotted to allow for cable alignment.
CABLE
10-32 x 1/2”
ANCHOR CABLE
SCREW (2)
BRACKET ANCHOR
BRACKET

FORWARD
POSITION
Reinstall the lower tiller cover.

Move the shift handle into the forward position. Adjust the lower rod
end and cable anchor bracket so that the cam roller is all the way to
the bottom of the cam slot. Shift to reverse and back to forward to
verify this roller position. Pull on the reverse gate to verify that it is
locked in forward.

18
Outboard Mounting Jet drive unit • Confirm the hull design of the boat is
When mounting the outboard motor onto the boat transom, the motor ingesting air compatible with a jet drive outboard
will have to be positioned to the height shown the image below using (cavitation) (page 3).
a straight edge under the boat. The bottom of the boat that is just in • Inspect the outboard mounting height, and
front of the jet drive intake should be level with the leading edge of the ensure the jet drive intake is set at the
intake. appropriate height (page 19).
The outboard motor transom bracket has four sets of upper mounting • Install a splash plate between the boat
holes. You will use one set to begin with. Mark pencil lines on the boat transom and jet drive intake (page 5).
transom through the other sets of holes. Then, if you wish to go up or
Shear key broken • Inspect the shear key for damage, and
down 3/8”, you can drill one alternate set of holes 3/8” up or down
replace if broken (page 7).
from the pencil marks. By alternating between these two sets of
transom holes and the four sets of motor holes, the motor can be Reverse gate • Inspect the reverse gate linkage, and
moved in 3/8” increments over almost one inch. incorrectly adjusted ensure it is properly adjusted, and that it
If you raise the motor too much, it will suck air and cavitate during start has not been damaged (page 6).
up or when banking on turns. When cavitating, the motor over speeds
Boat or jet intake • Ensure the jet drive intake is under water.
in spurs and shakes considerably in the motor mount. This is not a
not in water. • Ensure boat is not beached or sitting on
normal condition and should be avoided by proper adjustment of the
motor height on each individual boat. If you lower the motor too much, the river bottom.
you will have excessive drag. Therefore, mount the motor as high as
possible without allowing cavitation. Outboard propels while in neutral
Test run the boat, and then raise or lower the motor 3/8” at a time to
Possible Cause Correction
obtain the best results.
Reverse gate The jet unit will always provide a small
improperly amount of thrust while the engine is idling.
adjusted
Adjust the reverse gate linkage cable(s) in
the appropriate direction until the boat
remains stationary, or as close to stationary
as possible while in neutral.
A small amount of forward movement is
typically desired over reverse movement.

INTAKE LEADING EDGE

TECHNICAL INFORMATION
STRAIGHT EDGE

Serial Number Location

TROUBLESHOOTING
The possible causes listed are issues that may arise from the jet drive
unit, and assumes the outboard motor (engine) is working properly.

Poor performance
Possible Cause Correction

Clogged jet intake • Inspect and remove obstructions that may

be blocking the intake, such as leaves,
sticks, or gravel (page 4).

Worn or damaged • Inspect the impeller for wear or damage

impeller (page 6). JET DRIVE
• Inspect the impeller clearance, and ensure SERIAL NUMBER
it is within specification (page 6).
• Inspect the flanged liner for damage The serial number for the jet drive is located on the port side of the jet
(page 6). pump housing. Record the serial number in the space below. You will
need this serial number when ordering parts and when making
Incorrect outboard • Inspect the outboard mounting height, and technical or warranty inquiries.
mounting height ensure the jet drive intake is set at the
appropriate height (page 19).
Jet drive serial number: _________________________________

Date of purchase: _____________________________________

19
 Honda Publications
CUSTOMER INFORMATION This publication will give you information for maintaining and
repairing your jet drive outboard.

Register Your Jet Drive Outboard Owner’s Manual

Please take a few minutes and register your purchase with Honda. Keep this owner’s manual handy so you can refer to it at any time.
Only the outboard motor frame serial number needs to be registered. Consider this owner’s manual a permanent part of the outboard;
The serial number shown on the jet drive unit does not need to be please give it to the new owner if you resell the outboard.
registered. You can register by: The information and specifications included in this publication were in
• Going to marine.honda.com and clicking on Product Registration effect at the time of approval for printing. American Honda Motor Co.,
• Scanning this QR code. Inc. reserves the right, however, to discontinue or change
specifications or design at any time without notice and without
incurring any obligation whatever. No part of this publication may be
reproduced without written permission.

Parts and Service Items Frequently Asked Questions

Contact an authorized Honda Marine servicing dealer to purchase The Honda Marine web site provides additional
replacement parts, accessories, or other Honda Genuine items for information for users of Honda Marine products. Visit
your jet drive outboard. marine.honda.com and click on FAQs or scan the
QR code shown.
Dealer Locator Information
To find an authorized Honda Marine servicing dealer anywhere in the
United States:
Visit marine.honda.com and click on Find a Dealer.

How to Contact Honda

Honda Marine dealership personnel are trained professionals. They
should be able to answer any question you may have. If you
encounter a problem that your dealer does not solve to your
satisfaction, please discuss it with the dealership's management. The
Service Manager or General Manager can help. Almost all problems
are solved in this way.
If you are dissatisfied with the decision made by the dealership's
management, contact the Honda Marine Customer Relations Office.
You can write:
American Honda Motor Co., Inc.
Marine Division
Customer Relations Office
4900 Marconi Drive
Alpharetta, GA 30005-8847
Or telephone: (770) 497-6400 M-F, 8:30 a.m. - 7:00 p.m. ET
When you write or call, please give us this information.
• Model and serial number (page 19)
• Name of the dealer who sold the outboard to you
• Name and address of the dealer who services your outboard
• Date of purchase
• Your name, address, and telephone number
• A detailed description of the problem

20
 DISTRIBUTOR’S LIMITED WARRANTY
Honda Outboard Motors
This warranty is limited to Honda Outboard Motors and related original equipment distributed by American Honda Motor Co., Inc., Power Equipment Division,
4900 Marconi Drive, Alpharetta, Georgia 30005-8847.
Length of Warranty: (from date of original retail purchase)

Products Covered by Warranty: NON- STATE/LOCAL/

COMMERCIAL/
COMMERCIAL/ FEDERAL
RENTAL
NON-RENTAL GOVERNMENT
All models purchased on or after Jan. 1, 2016 (2) 60 months 24 months 36 months

All models purchased between July 1, 2008 and December 31,

60 months 12 months 24 months
2015 (2)

All models purchased on or before June 30, 2008 (1)(2) 36 months 12 months 24 months

Related original equipment items:

BF5 through BF20 models: Portable fuel tank and original
propeller. The same duration as the outboard with which they were purchased.(3)
All models: Primer bulb/fuel line assembly and tiller handle.
(1) Models purchased prior to July 1, 2008 (unless previously purchased with True-5 warranty from a participating dealer).
(2) 40, 65, & 105 Jet models: Jet pump assembly is a dealer installed option. Jet pump warranty is provided by Specialty Manufacturing Co. (Outboard Jets).
(3) Portable fuel tanks: 24 months or the same duration as the outboard they were purchased with, whichever is longer.

To Qualify for This Warranty:

The Honda Outboard Motor must be purchased from American Honda or a dealer authorized by American Honda to sell Honda Outboard Motors in the United
States, Puerto Rico, or the U.S. Virgin Islands. This limited warranty applies to the first retail purchaser and each subsequent owner during the applicable
warranty time period.

What American Honda Will Repair or Replace Under Warranty:

American Honda will repair or replace, at its option, any part that is proven to be defective in material or workmanship under normal use during the applicable
warranty time period. Warranty repairs and replacements will be made without charge for parts or labor. Anything replaced under warranty becomes the property
of American Honda Motor Co., Inc. All parts replaced under warranty will be considered as part of the original product and any warranty on those parts will expire
coincidentally with the original product warranty.

To Obtain Warranty Service:

You must, at your expense, take your Honda Outboard Motor and proof of the original purchase date to any dealer who is authorized to service Honda Outboard
Motors in the United States, Puerto Rico, or the U.S. Virgin Islands, during the dealer’s normal business hours. If you are unable to obtain warranty service, or are
dissatisfied with the warranty service you receive, take the following steps: First, contact the owner of the dealership involved; normally this should resolve the
problem. However, if you should require further assistance, write or call the Honda Marine Customer Relations Department of American Honda Motor Co., Inc.

American Honda Motor Co., Inc.

Honda Marine Customer Relations Department
4900 Marconi Drive
Alpharetta, Georgia 30005-8847
Telephone: (770) 497-6400
Exclusions:
This warranty does not extend to the following:
• Conditions caused by lack of routine maintenance or improper storage (as • Normal wear and tear
outlined in the owner’s manual) • Incorporation of unsuitable attachments or parts
• Conditions caused by the use of propeller(s) that do not allow the outboard • The unauthorized alteration, improper installation and/or rigging, or any
motor to run in its recommended full throttle rpm range causes other than defects in material or workmanship
• Operation inconsistent with the recommended operation/duty cycle (as • Corrosion to steering system or electrical components, corrosion due to
outlined in the owner’s manual) electrolysis, water born foreign chemicals, improper service or corrosion
• Parts affected or damaged by an abuse, submersion and/or collision caused by damage or abuse
• Fuel contamination and water entering the engine through the fuel intake, • Reimbursement for towing charges, in and out of water charges, or
air intake, or exhaust system technician travel time
• Operation with fuels, oils, additives and lubricants which are not suitable for • Growth of marine organisms on motor surfaces, external or internal
use in the product • Any product that has ever been declared a total loss or sold for salvage by
• Use in an application for which the outboard motor was not designed, such a financial institution or insurer, or that has been issued a “salvage” or
as racing or competitive use or any other misuse or neglect similar title under any state’s law.

Disclaimer of consequential damage and limitation of implied warranties:

American Honda disclaims any responsibility for loss of time or use of the outboard, revenue, or the equipment in which the outboard is installed, transportation,
commercial loss, or any other incidental or consequential damage. Any implied warranties are limited to the duration of this written limited warranty.
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages,
so the above exclusions and limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
PWL50415-M

21
 Accessories and Replacement Parts
This warranty is limited to Honda Marine parts, accessories and apparel when distributed by American Honda Motor Co., Inc., 1919 Torrance Blvd., Torrance,
California 90501-2746.
Products Covered by Warranty: Length of Warranty: (from date of original retail purchase)

STATE/LOCAL/
NON-COMMERCIAL COMMERCIAL/RENTAL FEDERAL
GOVERNMENT

Accessories other than noted below 12 months 3 months 3 months

Emission related accessories:

Portable fuel tanks, fuel line
24 months 24 months 24 months
assemblies, and water/fuel
separators

Replacement Parts 6 months 3 months 3 months

To Qualify for This Warranty:

1. The accessories or replacement parts must be purchased from American Honda or a dealer, distributor, or distributor’s dealer authorized by American
Honda to sell those products in the United States, Puerto Rico, and the U.S. Virgin Islands. Parts and Accessories must be purchased for installation on
original Honda equipment or engines to be eligible for warranty coverage. Installing Parts and Accessories on non-Honda products or engines voids this
warranty.
2. You must be the first retail purchaser. This warranty is not transferable to subsequent owners.

What American Honda Will Repair or Replace Under Warranty:

American Honda will repair or replace, at its option, any marine product accessories or replacement parts that are proven to be defective in material or
workmanship under normal use during the applicable warranty time period. Anything replaced under warranty becomes the property of American Honda Motor
Co., Inc. All parts replaced under warranty will be considered as part of the original product and any warranty on those parts will expire coincidentally with the
original product warranty.
Accessories and replacement parts, installed by a dealer who is authorized by American Honda to sell them, will be repaired or replaced under warranty without
charge for parts or labor. If installed by anyone else, accessories and replacement parts will be repaired or replaced under warranty without charge for parts, but
any labor charges will be the responsibility of the purchaser.

To Obtain Warranty Service:

You must, at your expense, take the Honda Outboard Motor product accessory or replacement part or the outboard motor or boat on which the accessory or
replacement part is installed, and proof of purchase to any Honda Marine authorized service facility or dealer in the United States, Puerto Rico, or the U.S. Virgin
Islands, during normal business hours.

Exclusions:
This warranty does not extend to accessories or parts affected or damaged by collision, normal wear, use in an application for which the product was not
designed or any other misuse, neglect, incorporation or use of unsuitable attachments or parts, unauthorized alteration, improper installation, or any causes other
than defects in material or workmanship of the product. Installing parts and accessories on non-Honda products or engines voids this warranty.

Disclaimer of consequential damage and limitation of implied warranties:

American Honda disclaims any responsibility for loss of time or use of the outboard motor, or the boat on which the product is installed, transportation,
commercial loss, or any other incidental or consequential damage. Any implied warranties are limited to the duration of this written warranty. Some states do not
allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above
exclusions and limitations may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

PWL50415-M

22
 EMISSION CONTROL SYSTEM WARRANTY
Your new Honda outboard engine complies with both the U.S. EPA and State of way affect emissions (including durability) could result in denial of coverage. If a
California emission regulations. American Honda provides the same emission non-Honda replacement part is used in the repair or maintenance of your engine,
warranty coverage for outboard engines sold in all 50 states. In all areas of the and an authorized Honda Marine dealer determines it causes the failure of a
United States your outboard engine must be designed, built, and equipped to meet warranted part, your warranty claim may be denied. If the part in question is not
the U.S. EPA and California Air Resources Board emission standard for spark related to the reason that your engine requires repair, your claim will not be denied.
ignited marine engines.
TO OBTAIN WARRANTY SERVICE:
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT You must take your Honda outboard engine, along with your sales registration card
YOUR WARRANTY RIGHTS AND OBLIGATIONS or other proof of original purchase date, at your expense, to any Honda Marine
The California Air Resources Board (CARB) and American Honda Motor Co., Inc. dealer that is authorized by American Honda Motor Co., Inc. to sell and service that
are pleased to explain the emission control system warranty on your 2018 Honda Honda marine product during its normal business hours. Claims for repair or
outboard engine. In California, new outboard engines must be designed, built, and adjustment found to be caused solely by defects in material or workmanship will not
equipped to meet the state’s stringent anti-smog standards. be denied because the engine was not properly maintained and used.
American Honda Motor Co., Inc. must warrant the emission control system on your If you are unable to obtain warranty service, or are dissatisfied with the warranty
outboard engine for the periods of time listed below provided there has been no service you received, contact the owner of the dealership involved. Normally this
abuse, neglect, or improper maintenance of your outboard engine. should resolve your problem. However, if you require further assistance, write or call
Your emission control system may include parts such as the carburetor or fuel the Honda Marine Customer Relations Office of American Honda Motor Co., Inc.
injection system, the ignition system, and catalytic converter. Also included may be EXCLUSIONS:
hoses, belts, connectors, and other emission-related assemblies.
Failures other than those resulting from defects in material or workmanship are not
Where a warrantable condition exists, American Honda Motor Co., Inc. will repair
covered by this warranty. This warranty does not extend to emission control
your outboard engine at no cost to you including diagnosis, parts, and labor.
systems or parts which are affected or damaged by owner abuse, neglect, improper
MANUFACTURER’S WARRANTY COVERAGE: maintenance, misuse, misfueling, improper storage, and/or collision, the
incorporation of, or use of, unsuitable attachments, or the unauthorized alteration of
Select emission control parts from model year 2010 and later outboard engines are
any part.
warranted for five years or 250 hours of use, whichever first occurs; or the length of
the Honda Marine Distributor’s Limited Warranty, whichever is longer. However, This warranty does not cover replacement of expendable maintenance items made
warranty coverage based on the hourly period is only permitted for engines in connection with required maintenance service after the items first scheduled
equipped with hour meters as defined in § 2441(a)(13)* or their equivalent. If any replacement as listed in the maintenance section of the product owner’s manual,
emission-related part on your engine is defective under warranty, the part will be such as: spark plugs and filters.
repaired or replaced by American Honda Motor Co., Inc. DISCLAIMER OF CONSEQUENTIAL DAMAGE AND LIMITATION
OWNER’S WARRANTY RESPONSIBILITIES: OF IMPLIED WARRANTIES:
As the outboard engine owner, you are responsible for the performance of the American Honda Motor Co., Inc. disclaims any responsibility for incidental or
required maintenance listed in your owner’s manual. American Honda Motor Co., consequential damages such as loss of time or the use of outboard engine, or any
Inc. recommends that you retain all receipts covering maintenance on your outboard commercial loss due to the failure of the equipment; and any implied warranties are
engine, but American Honda Motor Co., Inc. cannot deny warranty solely for the limited to the duration of this written warranty. This warranty is applicable only where
lack of receipts or your failure to ensure the performance of all scheduled the California or U.S. EPA emission control system warranty regulation is in effect.
maintenance.
EMISSION CONTROL SYSTEM WARRANTY PARTS:
As the outboard engine owner, you should, however, be aware that American
Honda Motor Co., Inc. may deny you warranty coverage if your outboard engine or a SYSTEMS COVERED
PARTS DESCRIPTION:
part has failed due to abuse, neglect, improper maintenance, or unapproved BY THIS WARRANTY:
modifications.
Fuel Metering Carburetor assembly, Throttle body, Fuel injector, Fuel pump,
You are responsible for presenting your outboard engine to a Honda Marine dealer Fuel pressure regulator,
as soon as a problem exists. The warranty repairs will be completed in a reasonable Throttle position sensor, Intake air temperature sensor,
amount of time, not to exceed 30 days. Engine temperature sensor,
Manifold absolute pressure sensor, Idle air control valve,
If you have any questions regarding your warranty rights and responsibilities, you Barometric pressure sensor,
should contact: Fuel line solenoid valve, Intake manifold, Intake valves,
and Oxygen sensor or Air fuel ratio sensor
American Honda Motor Co., Inc.
Marine Division Customer Relations Office Evaporative Portable fuel tank, Fuel cap, Fuel hoses, Primer bulb, Fuel
hose joint
4900 Marconi Drive
Alpharetta, Georgia 30005-8847 Air Induction Air intake duct, Vapor separator, Intake manifold tuning valve
Telephone: (770) 497-6400 (Intake air bypass control valve)

WARRANTY COVERAGE: Ignition Flywheel magneto, Ignition pulse generator, Ignition coil
assembly, Ignition control module,
See Manufacturer’s Warranty Coverage above for warranty coverage terms. This Engine control module, Crankshaft position sensor, Spark
warranty is transferred to each subsequent purchaser for the duration of the plug cap, Spark plug*,
warranty period. Knock sensor, and Camshaft position sensor
Warranty repairs will be made without charge for diagnosis, parts, and labor. All Lubrication System Oil pump and internal parts
defective parts replaced under this warranty become the property of American
Honda Motor Co., Inc. A list of warranty parts is on the adjacent column of this Crankcase Emission Crankcase breather tube, Positive crankcase ventilation
Control valve, Oil filler cap
statement. Normal maintenance items, such as spark plugs and filters, that are on
the warranted parts list are warranted up to their required replacement interval only. Exhaust Exhaust manifold and Exhaust valves
American Honda Motor Co., Inc. is also liable for damages to other engine
Valve Control System Rocker arm oil control valve
components caused by a failure of any warranted part during the warranty period.
Only Honda approved replacement parts will be used in the performance of any Miscellaneous Parts Tubing, fittings, seals, gaskets, and clamps associated with
warranty repairs, and they will be provided without charge to the owner. You may these listed systems.
use any replacement part as defined in § 1900(b)(20)* in the performance of any * Covered up to the first required replacement only. See the Maintenance Schedule in the
maintenance or repairs. Honda cannot deny coverage under the emission warranty owner’s manual.
solely for use of non-Honda replacement parts or service performed at a location
other than an authorized Honda dealership; however, use of a part that is not * California Code of Regulations PWL53247-N
functionally identical to the original equipment part in any respect that may in any
23
 This page intentionally left blank.

24
 TILLER HANDLE TEMPLATES

Tiller Handles with Troll Control

This template should be used when installing a tiller handle with troll control onto a jet drive Honda outboard. Before cutting the template out,
measure the ruler shown below to ensure the template is true to size. See page 17 for tiller handle modification and cable installation.
For additional copies of the tiller handle templates, go to marine.honda.com and click on Service & Support; then click on Owner’s Manuals to
locate the online copy of this owner’s manual, or you can contact an authorized Honda Marine dealer. When printing a copy of the template, do
not scale the page size.

NOTE:
DO NOT SCALE
PRINT 1:1

6"

150 mm
Check dimensions before drilling

25
 This page intentionally left blank.

26
Tiller Handles without Troll Control
This template should be used when installing a tiller handle without troll control onto a jet drive Honda outboard. Before cutting the template out,
measure the ruler shown below to ensure the template is true to size. See page 18 for tiller handle modification and cable installation.
For additional copies of the tiller handle templates, go to marine.honda.com and click on Service & Support; then click on Owner’s Manuals to
locate the online copy of this owner’s manual, or you can contact an authorized Honda Marine dealer. When printing a copy of the template, do
not scale the page size.

NOTE:
DO NOT SCALE
PRINT 1:1
CENTER
PIVOT
LINE

6"

150 mm
Check dimensions before drilling

27
 This page intentionally left blank.

28
NOTES

29
 NOTES

30
NOTES

31
AHM.320.2018.08
Printed in the U.S.A