Service Manual: Mono Laser MFP

Service Manual
MONO LASER MFP

SCX-483x/563x/573x Series
SCX-483xFR/FD/HD
SCX-563xFR/HR, SCX-573xFW
1. Speed • SCX-483xFR / SCX-5x3x series : 256 MB/ 768 MB
• SCX-483x series : 31 ppm in A4 / 33 ppm in Letter
5. Interfaces
The keynote of Product
• SCX-5x3x series : 35 ppm in A4 / 37 ppm in Letter

• High Speed USB 2.0
2. Processor • 10/100 BaseTX network connector (SCX-483xFD)
• SCX-483xFD : 360 MHz • 10/100/1000 BaseTX network connector
• SCX-483xFR / SCX-5x3x series : 600 MHz (SCX-483xFR/ SCX-5x3x series)
• 802.11b/g/n wireless LAN (SCX-573xFW)
3. Printer Languages
• PCL6, PS3 6. Toner cartridge (Initial / Sales)
• SCX-483x series : 2K / 2K, 5K
4. Memory (Std / Max) • SCX-5x3x series : 5K / 2K, 5K, 10K
• SCX-483xFD : 128 MB/ 384 MB
GSPN (Global Service Partner Network)
North America : service.samsungportal.com

Latin America : latin.samsungportal.com
CIS : cis.samsungportal.com
Europe : europe.samsungportal.com
China : china.samsungportal.com ⓒ Samsung Electronics Co.,Ltd. November. 2010
Asia : asia.samsungportal.com Printed in Korea.
Mideast & Africa : mea.samsungportal.com VERSION NO. : 1.00 CODE : 5737-00000E
Contents
chapter 1 Precautions
1.1 Safety Warning …………………………………………………… 1-1
1.2 Caution for safety ………………………………………………… 1-2
1.2.1 Toxic material ………………………………………………… 1-2
1.2.2 Electric Shock and Fire Safety Precautions ……………… 1-2
1.2.3 Handling Precautions ……………………………………… 1-3
1.2.4 Assembly / Disassembly Precautions …………………… 1-3
1.2.5 Disregarding this warning may cause bodily injury ……… 1-4
1.3 ESD Precautions ………………………………………………… 1-5
chapter 2 Product specifications and descriptions

2.1 Speci cations …………………………………………………… 2-1
2.1.1 Product Overview …………………………………………… 2-1
2.1.2 Features by models ………………………………………… 2-2
2.1.3 Speci cations………………………………………………… 2-3
2.1.4 Model Comparison Table …………………………………… 2-11
2.2 Product Description ……………………………………………… 2-12
2.2.1 Front View …………………………………………………… 2-12
2.2.2 Rear View …………………………………………………… 2-13
2.2.3 Paper Path …………………………………………………… 2-14
2.2.4 System layout ……………………………………………… 2-15
2.2.5 Hardware con guration …………………………………… 2-22
2.2.6 Engine F/W Control Algorithm ……………………………… 2-41
2.2.7 S/W Descriptions …………………………………………… 2-44
chapter 3 Disassembly and Reassembly

3.1 General precautions on disassembly ………………………… 3-1
3.2 Screws used in the printer ……………………………………… 3-2
Contents
3.3 Disassembly procedure ………………………………………… 3-3

3.3.1 Cover ………………………………………………………… 3-3
3.3.2 Scanner Assy ………………………………………………… 3-5
3.3.2.1 OPE board ……………………………………………… 3-6
3.3.2.2 CIS Unit ………………………………………………… 3-7
3.3.2.3 Scan Motor ……………………………………………… 3-8
3.3.2.4 Home Position Sensor ………………………………… 3-8
3.3.3 DADF Unit (SCX-563xFR / 563xHR / 573xFW) ………… 3-9
3.3.3.1 DADF Pick up unit ……………………………………… 3-9
3.3.3.2 DADF board …………………………………………… 3-10
3.3.3.3 DADF Motor …………………………………………… 3-11
3.3.4 ADF Unit (SCX-483xFR/FD/HD)) ………………………… 3-13
3.3.4.1 Tray Input ……………………………………………… 3-13
3.3.4.2 Front / Rear cover ……………………………………… 3-14
3.3.4.3 Paper Path Assy ……………………………………… 3-14
3.3.4.4 ADF Pick up unit ……………………………………… 3-15
3.3.4.5 ADF Motor ……………………………………………… 3-15
3.3.5 Middle Cover ………………………………………………… 3-16
3.3.6 Main board …………………………………………………… 3-17
3.3.7 HVPS board ………………………………………………… 3-17
3.3.8 SMPS board ………………………………………………… 3-18
3.3.9 Laser Scanning Unit (LSU) ………………………………… 3-18
3.3.10 Fuser unit …………………………………………………… 3-19
3.3.11 Main drive unit ……………………………………………… 3-20
3.3.12 Feed drive unit……………………………………………… 3-21
3.3.13 Pick up/ Regi/ MP clutch ………………………………… 3-21
3.3.14 Pick up roller ……………………………………………… 3-22
3.3.15 Transfer roller ……………………………………………… 3-22
3.3.16 MP unit ……………………………………………………… 3-23
3.3.17 Bin-full sensor ……………………………………………… 3-23
3.3.18 Regi. / Feed / Empty sensor ……………………………… 3-24
3.3.19 Cassette roller (Retard roller) …………………………… 3-25
Contents
chapter 4 Alignment and Troubleshooting

4.1 Alignment and Adjustments ……………………………………… 4-1
4.1.1 Control Panel ………………………………………………… 4-1
4.1.2 Understanding The Status LED …………………………… 4-6
4.1.3 JAM Removal ……………………………………………… 4-7
4.1.4 Useful menu item for service ……………………………… 4-15
4.1.5 Periodic Defective Image …………………………………… 4-17
4.1.6 Using the Easy Printer Manager program and smart panel … 4-18
4.1.7 Updating Firmware ………………………………………… 4-20
4.1.8 Tech Mode …………………………………………………… 4-23
4.2 Troubleshooting…………………………………………………… 4-28
4.2.1 Procedure of Checking the Symptoms …………………… 4-28
4.2.2 Error Message and Troubleshooting ……………………… 4-31
4.2.3 Image Quality problem ……………………………………… 4-49
4.2.4 Other errors ………………………………………………… 4-61
4.2.5 Network problems …………………………………………… 4-63
chapter 5 System Diagram

5.1 Block Diagram …………………………………………………… 5-1
5.2 Connection Diagram……………………………………………… 5-3
chapter 6 Reference Information

6.1 Tool for Troubleshooting ………………………………………… 6-1
6.2 Acronyms and Abbreviations …………………………………… 6-2
6.3 A4 ISO 19752 Standard Pattern ………………………………… 6-8
6.4 Selecting a location ……………………………………………… 6-9
attached Parts Catalog (Exploded Views & Parts List)

1. Precautions
1. Precautions
In order to prevent accidents and to prevent damage to the equipment please read the precautions listed
below carefully before servicing the printer and follow them closely.
1.1 Safety Warning

(1) Only to be serviced by appropriately quali ed service engineers.
High voltages and lasers inside this product are dangerous. This printer should only be serviced by a
suitably trained and quali ed service engineer.
(2) Use only Samsung replacement parts

There are no user serviceable parts inside the printer. Do not make any unauthorized changes or
additions to the printer, these could cause the printer to malfunction and create electric shock or re haz-
ards.
(3) Laser Safety Statement

The printer is certi ed in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter
J for Class I(1) laser products, and elsewhere is certi ed as a Class I laser product conforming to the
requirements of IEC 60825-1:1993 + A1:1997 + A2:2001. Class I laser products are not considered to
be hazardous. The laser system and printer are designed so there is never any human access to laser
radiation above a Class I level during normal operation, user maintenance or prescribed service condition.
• Wavelength: 800 nm
• Beam divergence
- Paraller: 12 degrees
- Perpendicular: 35 degrees
• Maximum power or energy output: 15 mW
WARNING
Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The
reflected beam, although invisible, can damage your eyes. When using this product, these basic safety
precautions should always be followed to reduce risk of fire, electric shock, and injury to persons:
1-1
Service Manual Samsung Electronics
SCX-483x/5x3x series
1. Precautions
1.2 Caution for safety

1.2.1 Toxic material
This product contains toxic materials that could cause illness if ingested.
(1) If the LCD control panel is damaged it is possible for the liquid inside to leak. This liquid is toxic. Contact
with the skin should be avoided, wash any splashes from eyes or skin immediately and contact your
doctor. If the liquid gets into the mouth or is swallowed see a doctor immediately.
(2) Please keep Drum cartridge and Toner Cartridge away from children. The toner powder contained in the
Drum cartridge and Toner Cartridge may be harmful and if swallowed you should contact a doctor.
1.2.2 Electric Shock and Fire Safety Precautions

Failure to follow the following instructions could cause electric shock or potentially cause a re.
(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a re or
electric shock.
(2) Use only the power cable supplied with the printer. Use of an incorrectly speci ed cable could cause the
cable to overheat and potentially cause a re.
(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could
lead to a re.
(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow
paper clips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to
an electric shock or re hazard.
(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock.
When servicing the printer remove the power plug from the wall socket.
(6) Use caution when inserting or removing the power connector. The power connector must be inserted
completely otherwise a poor contact could cause overheating possibly leading to a re. When removing
the power connector grip it rmly and pull.
(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or other
wise damaged. Do not place objects on top of the power cable. If the power cable is damaged it could
overheat and cause a re or exposed cables could cause an electric shock. Replace a damaged power
cable immediately, do not reuse or repair the damaged cable. Some chemicals can attack the coating on
the power cable, weakening the cover or exposing cables causing re and shock risks.
(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should
be repaired immediately. Take care not to cut or damage the power cable or plugs when moving the
machine.
(9) Use caution during thunder or lightening storms. Samsung recommend that this machine be disconnected
from the power source when such weather conditions are expected. Do not touch the machine or the
power cord if it is still connected to the wall socket in these weather conditions.
(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the
machine near a humidi er. Damp and dust build up inside the machine can lead to overheating and
cause a re.
(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise
possibly leading to the printer failing to work properly and in extreme conditions could lead to a re.
(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it
could make contact with a high voltage conductor inside the machine and cause an electric shock.
1-2
1. Precautions
1.2.3 Handling Precautions

The following instructions are for your own personal safety, to avoid injury and so as not to damage the
printer
(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could
cause the printer to tip or fall.
(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your
ngers, hair or clothing in any of these rotating devices.
(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer
which if spilled could get into the machine and cause damage or a shock or re hazard.
(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a
humidi er or heater. Damage could be caused to the printer in such areas.
(5) Do not place candles, burning cigarettes, etc on the printer, These could cause a re.
1.2.4 Assembly / Disassembly Precautions

Replace parts carefully, always use Samsung parts. Take care to note the exact location of parts and also
cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Please carry out the following procedures before dismantling the printer or replacing any parts.
(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if
the mainboard or network card is replaced.
(2) Ensure that power is disconnected before servicing or replacing any electrical parts.
(3) Disconnect printer interface cables and power cables.
(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or
temperature rating are correct.
(5) When removing or re- tting any parts do not use excessive force, especially when tting screws into
plastic.
(6) Take care not to drop any small parts into the machine.
(7) Handling of the OPC Drum
- The OPC Drum can be irreparably damaged if it exposed to light.
Take care not to expose the OPC Drum either to direct sunlight or to uorescent or incandescent
room lighting. Exposure for as little as 5 mins can damage the surface? photoconductive properties
and will result in print quality degradation. Take extra care when servicing the printer. Remove the
OPC Drum and store it in a black bag or other lightproof container. Take care when working with the
covers(especially the top cover) open as light is admitted to the OPC area and can damage the OPC
Drum.
- Take care not to scratch the green surface of OPC Drum Unit.
If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.
1-3
1. Precautions
1.2.5 Disregarding this warning may cause bodily injury

(1) Be careful with the high temperature part.
The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to
cool down before disassembly.
(2) Do not put nger or hair into the rotating parts.

When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor,
fan, etc.). If do, you can get harm.
(3) When you move the printer.

This printer weighs approx. 16 kg (35.27 lbs) including toner cartridge and cassette. Use safe lifting and
handling techniques. Use the lifting handles located on each side of the machine. Back injury could be
caused if you do not lift carefully.
(4) Ensure the printer is installed safely.

The printer weighs approx. 16 kg (35.27 lbs), ensure the printer is installed on a level surface, capable of
supporting its weight. Failure to do so could cause the printer to tip or fall possibly causing personal injury
or damaging the printer.
(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer
is stable.
1-4
1. Precautions
1.3 ESD Precautions

Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly
called “Electrostatically Sensitive (ES) Devices” or ESDs. Examples of typical ESDs are: integrated circuits,
some eld effect transistors, and semiconductor “chip” components.
The techniques outlined below should be followed to help reduce the incidence of component damage
caused by static electricity.
Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain

off any electrostatic charge on your body by touching a known earth ground. Alternatively, employ a
commercially available wrist strap device, which should be removed for your personal safety reasons prior
to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface,
such as aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity
of the assembly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an “anti-static” solder removal device. Some solder removal devices not classi ed as “anti-static”
can generate electrical charges suf cient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges suf cient to
damage ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most
replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a
comparable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch
the protective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed,
until completely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as
the brushing together of clothing fabric and lifting one’s foot from a carpeted oor, can generate static
electricity suf cient to damage an ESD.
1-5
2. Product specifications and descriptions

2.1 Specifications
2.1.1 Product Overview
1. Speed
• SCX-483x series : 31 ppm in A4 / 33 ppm in Letter
• SCX-5x3x series : 35 ppm in A4 / 37 ppm in Letter
2. Processor
• SCX-483xFD/HD : 360 MHz
• SCX-483xFR / SCX-5x3x series : 600 MHz
3. Printer Languages
• PCL6, PS3
4. Memory (Std / Max)

• SCX-483xFD/HD : 128 MB / 384 MB
• SCX-483xFR / SCX-5x3x series : 256MB / 768 MB
5. Interfaces
• High Speed USB 2.0
• 10/100 BaseTX network connector (SCX-483xFD/HD)
• 10/100/1000 BaseTX network connector
(SCX-483xFR / SCX-5x3x series)
• 802.11b/g/n wireless LAN (SCX-573xFW)
6. ADF (SCX-483xFD/HD) /
RADF (SCX-483xFR/ SCX-5x3x series)
7. Toner cartridge (Initial / Sales)

• SCX-483x series : 2K / 2K, 5K
• SCX-5x3x series : 5K / 2K, 5K, 10K
2-1
2.1.2 Features by models
SCX-4833FD SCX-5637FR
SCX-4833FR SCX-5737FW
Features SCX-4835FD SCX-5639FR
SCX-4835FR SCX-5739FW
SCX-4833HD SCX-5637HR
Print, Copy, Scan, Fax ● ● ● ●
Hi-Speed USB 2.0 ● ● ● ●
IEEE 1284 Parallel ○ ○ ○ ○

Network Interface
Ethernet 10/100 Base ●
TX wired LAN
Network Interface
Ethernet 10/100/1000 ● ● ●
Base TX wired LAN
Network Interface
802.11b/g/n wireless ●
LAN
Eco printing ● ● ● ●
Duplex (2-sided) printing ● ● ● ●
Samsung Easy Printer
● ● ● ●
Manager
Memory ○ ○ ○ ○
Tray 2 (520 sheets) ○ ○ ○ ○
SyncThru Web Service " ● ● ● ●
Automatic Document
●
Feeder (ADF)
Reversed Automatic
Document Feeder ● ● ●
(RADF)
( ●: Included, ○: Optional, Blank: Not available)
2-2
2.1.3 Specifications
• Product Specifications are subject to change without notice. See below for product specifications.
2.1.3.1 General Print Engine
Item SCX-483x series SCX-5x3x series

Engine Speed Simplex Up to 31 ppm in A4 (33 ppm in Letter) Up to 35 ppm in A4 (37 ppm in Letter)
Duplex Up to 15 ipm in A4 (16 ipm in Letter) Up to 17 ipm in A4 (18 ipm in Letter)
Warmup time From Sleep 15 sec 15 sec
FPOT From Ready As fast as 8 sec As fast as 8 sec
From Sleep As fast as 15.5 sec As fast as 15.5 sec
Resolution - Up to 1,200 x 1,200 dpi effective output Up to 1,200 x 1,200 dpi effective output
2.1.3.2 Copier specification

Copy Speed SDMC - Simplex to Simplex (1-1) : 30 sec - Simplex to Simplex (1-1) : 30 sec
(SDMC: Single - Simplex to Duplex (1-2) : 15 sec - Simplex to Duplex (1-2) : 15 sec
Document Multiple - Duplex to Simplex (2-1) : 30 sec (only - Duplex to Simplex (2-1) : 30 sec
Copy) 483xFR) - Duplex to Duplex (2-2) : 15 sec
- Duplex to Duplex (2-2) : 15 sec (only
483xFR)
MDMC - Simplex to Simplex (1-1) : 20 sec - Simplex to Simplex (1-1) : 24 sec
(MDMC: Multiple (483xFD/HD) / 24 sec (483xFR) - Simplex to Duplex (1-2) : 17 sec
Document Multiple - Simplex to Duplex (1-2) : 24 sec - Duplex to Simplex (2-1) : 10 sec
Copy) (483xFD/HD) / 17 sec (483xFR) - Duplex to Duplex (2-2) : 10 sec
- Duplex to Simplex (2-1) : 10 sec (only
483xFR)
- Duplex to Duplex (2-2) : 10 sec (only
483xFR)
FCOT From Ready @ As fast as 15 sec As fast as 12 sec
platen
From Sleep @ As fast as 23 sec As fast as 20 sec
platen
2-3

Resolution Text - Scan - Scan
Text and Photo 300x300 dpi @ ADF 600x300 dpi @ DADF
600x300 dpi @ DADF 600x600 dpi @ Platen
600x600 dpi @ Platen
- Print
- Print 600x600 dpi
600x600 dpi
Contrast Level 11 levels 11 levels
Darkness Level 11 levels 11 levels
Multicopy Max 99 copies Max 99 copies
2.1.3.3 Scanner Specification

Scan Method CIS CIS
Scan Speed Black 20 ipm @ 300 dpi (483xFD) 24 ipm @ 300 dpi
24 ipm @ 300 dpi (483xFR)
Gray 20 ipm @ 300 dpi (483xFD) 24 ipm @ 300 dpi
24 ipm @ 300 dpi (483xFR)
Color 6 ipm @ 300 dpi (483xFD) 8 ipm @ 300 dpi
8 ipm @ 300 dpi (483xFR)
Resolution Optical 1,200 x 1,200 dpi 1,200 x 1,200 dpi
Scanning Size ADF/DADF Max. Document Width : 216 mm Max. Document Width : 216 mm
Effective Scan Width : 208 mm Effective Scan Width : 208 mm
Max. Document Length : 356 mm Max. Document Length : 356 mm
Effective Scan Lenght : 348 mm Effective Scan Lenght : 348 mm
Platen Max. Document Width : 216 mm Max. Document Width : 216 mm
Effective Scan Width : 208 mm Effective Scan Width : 208 mm
Max. Document Length : 297 mm Max. Document Length : 297 mm
Effective Scan Lenght : 289 mm Effective Scan Lenght : 289 mm
Scan Format PDF, TIFF, TIFF uncompress, Multi- PDF, TIFF, TIFF uncompress, Multi-
TIFF, Multi-TIFF-uncompress, JPEG TIFF, Multi-TIFF-uncompress, JPEG
2-4
2.1.3.4 Fax Specification

Compression Method MH/MR/MMR, JBIG, JPEG MH/MR/MMR, JBIG, JPEG
Modem Speed 33.6 Kbps 33.6 Kbps
Transmission Speed Approx. 3 sec Approx. 3 sec
TX Resolution Normal 98 x 203 dpi 98 x 203 dpi
Fine 196 x 203 dpi 196 x 203 dpi
Gray Scale / Halftones 256 levels 256 levels
Fax Memory Type USB Memory stick USB Memory stick
Std 6 MB 50 MB
Page Capacity 480 pages 4000 pages
2.1.3.5 Controller & S/W

Processor - SCX-483xFD/HD : 360 MHz 600 MHz
- SCX-483xFR : 600 MHz
Memory Std. - SCX-483xFD/HD : 128 MB 256 MB
- SCX-483xFR : 256 MB
Max. - SCX-483xFD/HD : 384 MB 768MB
- SCX-483xFR : 768 MB
Flash - SCX-483xFD/HD : 16 MB 32 MB
- SCX-483xFR : 32 MB
Printer Languages PCL, PS3 PCL, PS3
Fonts 93 scalable, 1 bitmap 93 scalable, 1 bitmap
2-5

Driver Default Driver PCL PCL
Install PCL6 / PS3 PCL6 / PS3
Supporting OS Windows 2000/XP (32/64 bits) / Windows 2000/XP (32/64 bits) /
Vista (32/64 bits) / Vista (32/64 bits) /
2003 Server (32/64 bits) / 2003 Server (32/64 bits) /
2008 Server(32/64 bits) / 2008 Server(32/64 bits) /
7 (32/64 bits) /2008 Server R2 7 (32/64 bits) /2008 Server R2
Various Linux OS: Various Linux OS:
Fedora Core 4, 5, 6 Fedora Core 4, 5, 6
Fedora 7, 8, 9, 10, 11, 12 Fedora 7, 8, 9, 10, 11, 12
RedHat Enterprise Linux WS 4, 5 RedHat Enterprise Linux WS 4, 5
SuSE 10.0, 10.1 SuSE 10.0, 10.1
openSuSE 10.2, 10.3, 11.0, 11.1, 11.2 openSuSE 10.2, 10.3, 11.0, 11.1, 11.2
SuSE Linux Enterprise Desktop 10, 11 SuSE Linux Enterprise Desktop 10, 11
Debian 4.0, 5.0 Debian 4.0, 5.0
Ubuntu 5.04, 5.10, 6.04, 6.10, 7.04, 7.10, Ubuntu 5.04, 5.10, 6.04, 6.10, 7.04, 7.10,
8.04, 8.10, 9.04, 9.10 8.04, 8.10, 9.04, 9.10
Mandriva 2005LE, 2006, 2007, 2007.1, Mandriva 2005LE, 2006, 2007, 2007.1,
2008, 2008.1, 2009, 2009.1 2008, 2008.1, 2009, 2009.1
Mac OS 10.3 ~ 10.6 Mac OS 10.3 ~ 10.6
Citrix Presentation Server Citrix Presentation Server
Windows Terminal Services Windows Terminal Services
WHQL Windows 2000/XP(32/64bits)/ Windows 2000/XP(32/64bits)/
Vista(32/64bits)/2003 Vista(32/64bits)/2003
Server(32/64bits)/2008 Server(32/64bits)/ Server(32/64bits)/2008 Server(32/64bits)/
7(32/64bit)/2008 Server R2(64bits) 7(32/64bit)/2008 Server R2(64bits)
Compatibility SPL & PCL6: Win 2000/ SPL & PCL6: Win 2000/
XP(32/64bits)/2003 Server(32/64bits)/ XP(32/64bits)/2003 Server(32/64bits)/
Server(32/64bits)/7(32/64bits) Server(32/64bits)/7(32/64bits)
PS3: Win 2000/XP(32/64bits)/ PS3: Win 2000/XP(32/64bits)/
server(32/64bits)/2008 server(32/64bits)/2008
Server(32/64bits)/7 (32/64bits) PPD, Server(32/64bits)/7 (32/64bits) PPD,
Mac PPD, Linux PPD Mac PPD, Linux PPD
Wired Network Protocol TCP/IP, Ethertalk, SNMP, HTTP 1.1 TCP/IP, Ethertalk, SNMP, HTTP 1.1
Supporting OS Windows 2000/XP(32/64bits)/2003 Windows 2000/XP(32/64bits)/2003
Server(32/64bits)/Vista(32/64bits)/2008 Server(32/64bits)/Vista(32/64bits)/2008
Server(32/64bits) Server(32/64bits)
Mac OS 8.6~9.2, 10.1~10.5 Mac OS 8.6~9.2, 10.1~10.5
Various Linux OS including Red Hat 8~9, Various Linux OS including Red Hat 8~9,
Fedora Core 1~4, Mandrake 9.2~10.1, Fedora Core 1~4, Mandrake 9.2~10.1,
and SuSE 8.2~9.2 and SuSE 8.2~9.2
NetWare 5.x, 6.x (TCP/IP Only) NetWare 5.x, 6.x (TCP/IP Only)
Unix HP-UX Unix HP-UX
2-6

Wireless Protocol N/A Only SCX-573xFW : 802.11n
Network
Application Smart Panel SmartPanel for Macintosh/LINUX SmartPanel for Macintosh/LINUX
Printer Setting PSU for Macintosh/LINUX PSU for Macintosh/LINUX
Network SyncThru Web Admin Service 5.0 SyncThru Web Admin Service 5.0
Management
IP Setting SetIP SetIP
Others Easy Printer Manager (Windows Only), Easy Printer Manager (Windows Only),
SmarThru Office , DPU, PC fax SmarThru Office , DPU, PC fax
Interface
IEEE 1284 Parallel Optional Optional
USB Hi-Speed USB 2.0 Hi-Speed USB 2.0
Wired Network - 483xFD/HD :Ethernet 10/100 Base TX Ethernet 10/100/1000 Base TX (Internal)
(Internal)
- 483xFR : Ethernet 10/100/1000 Base
TX (Internal)
Wireless Network N/A Only SCX-573xFW : 802.11n
User Interface
LCD - 483xFD/HD : 2-Line - 563x series : 4- Line
- 483xFR : 4-Line - 573x series : 4.3 inch Touch Screen
2.1.3.6 Paper Handling

Standard Capacity 250-sheet Cassette Tray, 50-sheet Multi 250-sheet Cassette Tray, 50-sheet Multi
Purpose Tray @80g/㎡ Purpose Tray @80g/㎡
Max. Capacity 820 sheets @ 80g/㎡ 820 sheets @ 80g/㎡
Printing Max. Size 216 x 356 mm (8.5" x 14") 216 x 356 mm (8.5" x 14")
Min. Size 76 x 127 mm (3.0" x 5.0") 76 x 127 mm (3.0" x 5.0")
Multi-purpose tray
Capacity Plain Paper 50 sheets @ 80g/㎡ 50 sheets @ 80g/㎡
Envelop 5 sheets 5 sheets
Media sizes A4, A5, A6, Letter, Legal, Folio, Oficio, A4, A5, A6, Letter, Legal, Folio, Oficio,
Executive, ISO B5, JIS B5, 3"x5", Executive, ISO B5, JIS B5, 3"x5",
Envelope(Monarch, No.10, DL, C5, C6), Envelope(Monarch, No.10, DL, C5, C6),
Custom Custom
2-7

Media type Plain, Thin, Thick, Thicker, Cotton, Colored, Plain, Thin, Thick, Thicker, Cotton, Colored,
Envelope, Transparency, Pre-Printed, Envelope, Transparency, Pre-Printed,
Recycled, Labels, Bond, Card stock, Recycled, Labels, Bond, Card stock,
Archive Archive
Media weight 16~58lb (60 to 220g/㎡) 16~58lb (60 to 220g/㎡)
Sensing Paper Empty Paper Empty
Standard Cassette Tray
Capacity 250 sheets @ 80g/㎡ 250 sheets @ 80g/㎡
Executive, ISO B5, JIS B5, Custom Executive, ISO B5, JIS B5, Custom
Media types Plain Paper, Thin, Thick, Recycled, Bond, Plain Paper, Thin, Thick, Recycled, Bond,
Cardstock, Archive Cardstock, Archive
Optional Cassette Tray
Capacity 520 sheets @ 80g/㎡ 520 sheets @ 80g/㎡
Executive, ISO B5, JIS B5 Executive, ISO B5, JIS B5
Media types Plain Paper, Thin, Thick, Recycled, Bond, Plain Paper, Thin, Thick, Recycled, Bond,
Cardstock, Archive Cardstock, Archive
Output Stacking
Capacity Face-Down 150 sheets @ 80g/㎡ 150 sheets @ 80g/㎡
Face-Up 1 sheet 1 sheet
Output Full sensing Yes Yes
Duplex
Supporting Built-in Built-in
Media sizes A4, Letter, Oficio, Folio, Legal A4, Letter, Oficio, Folio, Legal
Media types Plain Paper, Thin, Thick, Recycled, Bond Plain Paper, Thin, Thick, Recycled, Bond
Document Thickness
Non-Printable Envelop 10mm(0.4") from edge(Top, Bottom, Left, 10mm(0.4") from edge(Top, Bottom, Left,
Area Right) Right)
Other Media 4mm(0.16") from edge(Top, Bottom, Left, 4mm(0.16") from edge(Top, Bottom, Left,
Right) Right)
RADF/ADF
Type - 483xFD/HD : ADF RADF
- 483xFR : RADF
Capacity 50 sheets @ 20lb 50 sheets @ 20lb
2-8

Document Width - ADF : 142~216mm 145~216mm
Size - RADF : 145~216mm
Length - ADF : 148~356mm 145~356mm
- RADF : 145~356mm
Paper Weight - ADF : 16~28lb 12.5~ 28 lb
- RADF : 12.5~28lb
2.1.3.7 Consumables

Toner Black - Standard: Average Cartridge Yield 2K - Standard: Average Cartridge Yield 2K
standard pages. standard pages.
- High Yield: Average cartridge Yield 5K - High Yield: Average cartridge Yield 5K
standard pages. standard pages.
Declared cartridge yield in accordance - Extra High Yield: Average cartridge
with ISO/IEC 19752. Yield 10K standard pages.
Declared cartridge yield in accordance
with ISO/IEC 19752.
Key Electronic key(CRUM) Only Electronic key(CRUM) Only
Life detect Toner gauge sensor by dot count Toner gauge sensor by dot count
Drum Yield N/A N/A
2.1.3.8 Reliability & Service

Recommanded AMPV 1000 sheets/month 1500 sheets/month
Max AMPV 2500 sheets/month 3500 sheets/month
Max. Monthly Duty 50,000 sheets/month 80,000 sheets/month
MPBF 35,000 sheets 45,000 sheets
MTBF 35 months 35 months
MTTR 30 min. 30 min.
ADF / RADF Unit life - ADF : 20,000 sheets - DADF : 80,000 sheets
- DADF : 80,000 sheets
SET Life Cycle 170,000 sheets or 5 years (whichever 220,000 sheets or 5 years (whichever
comes first) comes first)
2-9
2.1.3.9 Maintenance part
Item Part Code Life

Transfer roller JC66-02842A Approx. 100,000 Pages
Fuser Unit JC91-01023A (110V) Approx. 90,000 Pages
JC91-01024A (220V)
Pick-up Roller JC73-00340A Approx. 90,000 Pages
Retard Roller JC90-01032A Approx. 60,000 Pages
RADF rubber pad JC97-03069A Approx. 20,000 pages
2.1.3.10 Environment

Operating Environment Temperature 10C to 32C 10C to 32C
Humidity 20% to 80% 20% to 80%
Acoustic Noise Printing 51dBA 52dBA
Level(Sound Power/ Standby 26 dBA 26 dBA
Pressure)
Sleep Back Ground Level Back Ground Level
Power Consumption Ready Less than 50W - 563xFR/HR : Less than 50W
- 573xFW : Less than 65W
AVG. Less than 600W Less than 650W
Power Save Less than 8W - 563xFR/HR : Less than 8W
- 573xFW : Less than 10W
Dimension (W x D x H) SET - 483xFD : 407 x 424 x 382 mm 447 x 469 x 438 mm
- 483xFR : 447 x 469 x 438 mm
Weight SET - 483xFD : 14 Kg 16 Kg
- 483xFR : 16 Kg
2.1.3.11 Options

Memory * 483xFD/HD - ML-MEM170: 512 MB
- CLP-MEM202 : 256MB
* 483xFR
- ML-MEM170: 512 MB
Second Cassette 520-sheet Cassette Tray 520-sheet Cassette Tray
(ML-S3710A) (ML-S3710A)
2-10
2.1.4 Model Comparison Table
Samsung Samsung Brother Lexmark

SCX-563xFR SCX-483xFD MFC-8890DW X264DN
Image
35 ppm (A4) 31 ppm (A4)

Speed 30 ppm (A4) 28 ppm (A4)
37 ppm (Letter) 33 ppm (Letter)
Processor 600 MHz 360 MHz - 266 MHz
Memory
256 / 768 MB 128 / 384 MB 64 / 576 MB 64 / 64 MB
(Std/Max)
Emulation PCL6/PS3 PCL6/PS3 PCL6 PCL6/PS3
MP/Cassette 50 / 250 50 / 250 50 / 250 1 / 250
SCF 520 sheets 520 sheets 250 sheets 250 / 550 sheets
Duplex Std. Std. Std. Std.
Toner Yield 2K/ 5K / 10K 2K / 5K 3K/ 8K 3.5K / 9K
- High speed USB 2.0 - High speed USB 2.0 - High speed USB 2.0 - High speed USB 2.0
Interface - Ethernet 10/100/1000 - Ethernet 10/100 Base - Ethernet 10/100 Base - Ethernet 10/100 Base
Base TX) TX TX TX
2-11
2.2 Product Description
This chapter describes the functions and operating principal of the main component.
2.2.1 Front View
X Y
X[ X^
Z
XZ [ X_
XY X\ X`
XX \
X]
XW ]
^
`
NOTE
• This illustration may differ from your machine depending on its model.
• Some features and optional goods may not be available depending on model or country.
1 Document feeder cover 11 Multi-purpose tray

2 Document feeder width guide 12 Output tray
3 Document feeder input tray 13 Control panel
4 Document feeder output tray 14 Multi-purpose tray paper extension
5 Front cover 15 Paper width guides on a multi-purpose tray
6 Control board cover 16 Output support
7 Handle 17 Scanner lid
8 Paper level indicator 18 Scanner glass
9 Tray2 (optional) 19 USB port
10 Tray1 20 Handset
2-12
2.2.2 Rear View
XX
Y
XW
Z
]
`
^ _
NOTE
• This illustration may differ from your machine depending on its model.
• Some features and optional goods may not be available depending on model or country.
1 EDI port 7 Duplex Unit

2 Network port 8 Rear cover
3 USB port 9 Tray back cover
4 IEEE 1284 parallel connector (optional) 10 Telephone line socket
5 Power-switch 11 Extension telephone socket (EXT)
6 Power receptacle
2-13
2.2.3 Paper Path
[1] Simplex [2] Duplex [3] MP
2-14
2.2.4 System layout
This model is consisted of the Engine parts and F/W. The engine parts is consisted of the mechanical
parts comprising Frame, Feeding, Developing, Driving, Transferring, Fusing, Cassette and H/W comprising
the main control board, power board, operation panel, PC Interface.
132
12 14
11
10
2
9 4
3
5
6
8
1 LSU 8 Duplex
2 Cartridge 9 Fuser
3 Regi roller 10 Exit roller1
4 MP 11 Exit roller2
5 Feed roller 12 Scanner (Platen)
6 Pick up roller 13 DADF/ADF
7 Cassette 14 OPE
2-15
2.2.4.1 Feeding Part
It is consists of a basic cassette, an MP tray for supplying different types of media (envelope, label, special
paper) and parts related to paper transferring.
1) Tray
The basic tray is located on front side of the machine and allows feeding of common paper. Paper size is set
using the Size Guides in each tray. Adjust the Paper length/width guides to match the paper size.
3 1
LGL
A4
LTR 1 Paper length guide

2
2 Support guide
3 Paper width guide
2) Pick up / Retard Roller
When pickup takes place, the pickup roller rotates to separate and transport the paper.
The pickup roller rotates when the pickup clutch is activated. The retard roller serve to make sure
that a single sheet of paper is moved to the paper path, and the paper is moved as far as the registration
roller by the work of the feed roller. The following is a diagram of the pickup section:
Pickup Roller
Feed Roller Regi. Roller
Retard Roller
2-16
3) Registration roller
It has a paper arranging function, paper transferring function, paper detecting function, jam removing
function, and so on.
4) MP tray
The multi-purpose tray can hold special sizes and types of print material, such as postcards, note cards, and
envelopes. It is useful for single page printing on letterhead or colored paper. It uses 3 rollers feeding method
to feed 50 sheets of general papers.
5) Duplex unit
It has paper transferring function, paper guide function, jam removing function.
It is designed for basic attachment, and the duplex feeding takes a side feeding method. Usable
papers are A4, letter, and legal size paper. For removing a jam occurred in a front part, it is designed to open
a cassette and a guide.It is designed to open a rear cover to remove a jam in a rear part. If a face up tray is
open, the duplex option cannot be used.
6) SCF (Second Cassette Feeder)
It is the same method with the main cassette, and the capacity is 520 sheets.
It has a separate driving mechanism. It is designed for a common use with a main cassette.
2-17
2.2.4.2 Imaging unit
1) Printing process overview
LSU
Toner Cartridge
OPC Drum
Transfer Roller
This mono printing system includes the LSU with a laser beams, a toner cartridge and transfer roller.
This machine uses single toner cartridge and dual laser beams for mono printing. The toner cartridge
consists of Drum unit and Development unit. The Drum unit has an OPC drum, cleaning blade.
The OPC drum is charged with a negative voltage by the scorotron and is exposed by the light from the LSU
(Laser Scanning unit). The light produced by a laser creates a latent image by discharging on the surface
of the OPC drum. The negatively charged toners are attracted to the latent image due to and electric filed.
The toners(real image) on the OPC drum are moved to the transfer media by the positive bias applied to the
transfer roller.
1. Charging the OPC drum: The scorotron gives the drum negative charges.
2. Laser exposure: Light produced by a laser diode irradiates the charged OPC through the lens and mirrors.
3. Development: This machine uses a dual-component development system . The magnetic roller carries negatively
charged toner to the latent image on the drum surface.
4. Transfer: The transfer rollers opposite the OPC drums transfer toner from the drums to the transfer media (e.g.
paper, OHP film, etc).
5. Cleaning for OPC drum: The cleaning blade removes remaining toners on the drum surface after image transfer
to the paper.
2-18
2) Toner cartridge
By using the electronic photo process, it creates a visual image. In the toner cartridge, the OPC unit and the
developing unit are in a body. The OPC unit has OPC drum and charging roller, and the toner cartridge unit
has toner, supply roller, developing roller, and blade (Doctor blade)
• Operation condition : Temp 10~30℃, Humidity 20~85% RH

• Developing Method : Non magnetic 1 element contacting method
• Toner : Non magnetic 1 element shatter type toner
• The life span of toner (ISO 19752 pattern / A4 standard)
→ Initial toner : 2K (483x series) / 5K (5x3x series)
→ Sales toner : 2K / 5K / 10K(only 5x3x series)
• Toner Residual Sensor : Dot count with CRUM(CRU Monitor)
• OPC Cleaning : Collect the toner by using cleaning blade
• Handling of wasted toner : Collect the wasted toner in the cleaning frame by using cleaning blade
• OPC Drum Protecting Shutter : None
• Classifying device for toner cartridge: ID is classified by CRUM.
ⓐ Charge Roller ⓕ Supply Roller

ⓑ Drum OPC ⓖ Charge Cleaning Roller
ⓒ Cleaning Blade ⓗ Agitator 1
ⓓ Doctor Blade ⓘ Agitator 2
ⓔ Developer Roller
2-19
2.2.4.3 Fuser unit
It is consisted of a halogen lamp, heat roller, pressure roller, thermistor and thermostat. It sticks the toner on
a paper by heat and pressure to complete the printing job.
Thermistor
Thermostat
Heat Roller
Halogen Lamp
Pressure Roller2
Pressure Roller
1) Thermostat
When a heat lamp is overheated, a Thermostat cuts off the main power to prevent overheating.
- Thermostat Type : Non- Contact type THERMOSTAT
- Control Temperature : 170℃ ± 5℃
2) Thermistor
It is a temperatrue detecting sensor.
- Temperature Resistance : 7㏀ (180℃ )
3) Heat roller
The heat roller transfers the heat from the lamp to apply a heat on the paper.
The surface of a heat roller is coated with Teflon, so toner does not stick to the surface.
4) Pressure roller
A pressure roller mounted under a heat roller is made of a silicon resin, and the surface also is coated with
Teflon. When a paper passes between a heat roller and a pressure roller, toner adheres to the surface of a
paper permanently.
5) Halogen Lamp
- Voltage 120 V : 115 ± 5 %
220 V : 230 ± 5 %
- Capacity : 850 Watt ± 25 W
2-20
2.2.4.4 LSU (Laser Scanning Unit)
It is the core part of the LBP which switches from the video data received to the controller to the electrostatic
latent image on the OPC drum by controlling laser beam, exposing OPC drum, and turning principle of
polygon mirror. The OPC drum is turned with the paper feeding speed. The /HSYNC signal is created when
the laser beam from LSU reaches the end of the polygon mirror, and the signal is sent to the controller.
The controller detects the /HSYNC signal to adjust the vertical line of the image on paper. In other words,
after the /HSYNC signal is detected, the image data is sent to the LSU to adjust the left margin on paper.
The one side of the polygon mirror is one line for scanning.
OPC Drum
Photo Diode
Polygon Mirror
Polygon Motor
LD Driver circit Motor Driver
LD(Laser Diode)
Protector panel
2-21
2.2.5 Hardware configuration
The SCX-483x series Electrical Circuit System consists of the following:
• Main Controller
• OPE Controller
• DDR2 SODIMM (Option)
• SCF(Option)
• SMPS
• HVPS
Diagram of the SCX-483x series Electrical Circuit
zG
ADF ADF_JOINT
zwlhrly
o
z
S CX-4932FN
ONLY
i|ly
OPE _LCD
LCD (2-Line)
t{ 1 OUT2B
2 OUT2A
3 OUT1B
CIS
z{lw
LSU
4 OUT1A
MODEM
1
2
CN(1.5mm)
5 GND
mnuk CN(1.5mm)
1
2
1
2
3
6 GND
z
A DF _IF
S CANNER_HOM E
A DF_IF
(Conexant ) (Dual Beam )
hkmwwvz zlu
7 3.3VPS
8 GND t
OPE
GND
GND
GND
nRD
nWR
N. C
3. 3V _LS U
GND
V DO _1_N
GND
GND
V DO _2_N
GND
nLD_O N
LD_P OWE R
N. C
nREA DY _LS U
19 nLSU_M OT_E N
GND
nHsy nc
nA DF_COV ER_SE NS
5V
K EY CLI CK
3. 3V
3. 3V
V DO_1_P
V DO_2_P
24V S
nCS _MO DE M
nI NT_MO DE M
9 nADF_P _POS
HOOK _DET
nM _RE S ET
17 CLK_LS U_MOT
DAT A7~
A DDR1~
~DA TA0
~A DDR7
nRING0
nS H_1
nS H_2
hkmjv}lyvwlu 10 nADF_COVER_SENS
GND
11 GND
t{
nA DF_P _POS
nA DF_P _DE T
hkmwwvz zlu
5V
12 nADF_P _DET
z{lw
O UT 2B
O UT 2A
O UT 1B
O UT 1A
3. 3VP S
12~
~10
~18
G ND
G ND
G ND
G ND
3~
11
19
20
21
22
23
24
25
26
27
28
29
30
10
11
12
13
14
15
16
18
20
21
22
10
10
11
12
1
2
1
2
3
4
5
6
7
8
9
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
12
11
10
9
8
7
6
5
4
3
2
1
A DDR1~ 12~
~DA TA0 ~10
~A DDR7 ~18
10
11
12
13
14
15
16
17
18
19
20
10
DAT A7~ 3~
10
11
12
10
11
12
GND 11
GND 19
HOOK _DET 20
nCS _MO DE M 21
nRD 22
nW R 23
N. C 24
nRS T_MO DE M 25
nI NT_MO DE M 26
N. C 27
3. 3V 28
3. 3V 29
GND 30
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
3
4
5
6
7
8
9
GND 1
2
3. 3V _LS U
GND
V DO _1_N
GND
GND
V DO _2_N
GND
nLD_O N
LD_P OWE R
N. C
nREA DY _LS U
nLSU_M OT_E N
GND
nHs ync
V DO_1_P
V DO_2_P
24V S
CLK_LS U_MOT
nS H_1
nS H_2
GND
GND
GND
GND
GND
CI S_B LE D
CIS _GLE D
CI S_RLE D
GND
MOD_B UZ ZE R_CON
OUT2B
OUT2A
OUT1B
OUT1A
3. 3VP S
nADF _P_P OS
nA DF_COVE R_SE NS
OUT1A
OUT1B
OUT2A
OUT2B
3. 3V _CI S
PULL-UP
CI S_S P
3CIS _CLK
12V
5V
nADF_P _DET
AF E_S IG
SCA N_CONTROL1
thpu
SCA NNE R_HOME
KE YCLI CK _CON
nRS T_P ANE L
nPOWE R_SW
PA NEL_RX D
ZUZ}ztwz ZUZ}jv
PA NEL_TX D
CN9(FFC 1mm) CN21(FFC 1mm)
GND
GND
GND
CN4(2mm )
mGj SCAN_MTR CN26(FFC 1mm) MODE M_IF LS U_IF
tG CIS _IF
CN3(1.5mm) CN5(1.5mm )
z OP E I/F
A DF_IF 24V 1
24V 2
24V 3
3.3V 4
24V S
GND
12
11 Y[}z 1
2
24V S
GND ͶͶ΁΃΀;
3.3V 5
3.3V 6
THV_RE A D 10
͵͵΃ͣ͑
CN8(1.5mm)
ZUZ}z 3 THV _RE A D
CN16(2mm)
nRS T_S CF 7
nTHV_E N 9 4 nTHV _E N ;ͣͥͦͣ͢
SCF_IF
P WM_THV 8 S CF_TX D 8
΄͵΃Ͳ;
o}wz
5 P WM _THV
S CF_RX D 9
P WM_DE V_DC 7
͙͑ͧͥͼ͚
HVP S
6 P WM _DE V_DC
P WM_MHV 6 7 P WM _MHV N. C 10
Supply P WM_FUS E R_B IA S
GND
5
4
8 P WM _FUS E R_B IA S ͙ͣͩ͢;ͳ͚ nS CF_OP T 11
9 GND N. C 12
GND 3
DEV 3.3V S 2
10
11
GND
3. 3V S
N. C 13
GND 14
THV 3.3V _Cov er_Open 1
ZUZ}jvX 12 3. 3V_Cover_Open GND 15
GND 16
OPC MHV ΄Ͷ΃ͺͲͽ͑͑ͷͽͲ΄͹ GND 17
GND 18
͙ͩ;ͳ͚
Ϳ΀΃͑ͷͽͲ΄͹
M AI N FA N
1
͙ͧ͢;ͳ͚
CN12
GND 1
(2m m)
GND
2 GND 2
Varistor 3 24V S }jsr NC
3
CN7 NETWORK_IF
RD-
4
S
mhu
CHORUS3 25MHz
3.3V
RD+
5
6
M
TD-
D C |ziGGjsr
3.3V
7
8
FUSER thpu 1
3.3V pullup
9
R
GND LE D1
CN23
10
CRUM
(2mm )
BIAS DRUM
2 CLK
DIO
3.3V
11
U
3
Clock LE D2
12
4 3.3V _CRUM
Generator ͿΖΥΨΠΣΜ GND
13
M
GND
14
ASM3P2863 A thpuGjsr ͢͢͡͠͡͡
SM PS F AN
CN11
T mhu
(2m m)
V B US 1
USB_IF
1 24V S
CN28
2 GND DM 2
kl}lsvwlyG|
ztwz ͺ΄΁ͦͩͣ͢
DP 3
12MHz
GND 4
USB 2.0
S MP S FA N
(1.5m m)
CN30
mhu 1 24V S
PA RALLE L
P OWER GND 1
USB TO
CN20
2 GND 5V 2
t NC 3 PARALLEL
ztwz GND
24V OFF
1
2
CN(2mm)
CN15
CN4
5 GND CN14(2mm)
SM PS
CN(2 mm) CN6(1. 5mm) (1 .5mm )

Relay 3 Y[}z 4 24V OFF
CN(2mm ) CN24(1. 5mm ) CN19
(2mm)
P_EXIT OUTBIN AIR

SENSOR
CN18
MAIN MOTOR
S MP S
CN10( 2mm) MP E raser&Duplex

24V S 4 3 Relay THERM
SENSOR SENSOR TEMP USB_IF
Fuser ON 5 24V S
2
3.3V_C_OPEN1
3.3V_C_OPEN2
nSENS_BIN_ FU LL
P EA PE R_EX IT
E RA SE R_LED
1 Fuser ON
MO T_REA DY
nSENS_DUPLEX
MO T_BRE AK
FE ED_S ENS
REG I_S ENS
m|zlyGvu
Pi ck up_CLT
PW M_MO T
MP _SE NS
THE RM_1
Regi_CLT
A MB IE NT
MO T_DIR
P _E mpt y
MP _CLT
MO T_EN
3.3V PS
5V _S MP S 1 1 5V_S MP S
3.3V S
3.3V S
S ENS
3.3V S
3.3V S
CN17
VB US
24VS
GND
GND
GND
GND
GND
GND
GND
GND
24VS
24VS
24VS
24VS
SM PS
GND
GND
GND
GND
CN3
3.3V
2 GND
SM PS
GND 2
DM
5V
DP
24V 3 3 24V
4 GND
GND 4
Y[}
1
2
10
11
12
13
14
1
2
3
4
5
1
2
3
1
2
3
4
5
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
1
2
3
4
5
6
7
8
9
1
2
3
4
\}ztwz
INLET FUSER
{X js zvs zvs

h
10
9
8
7
6
5
4
3
2
1
{
lyhzly k z
y tw tw l wG j
w ltw{ ylnp mllk slk
j z z v v
j j z z z
z k
{z m|zlyG| t{ |zi
iskj
t Rainier Hardware Team

pusl{ t R&D Group 2
Digital Print Division
Samsung Electronics
100409
The Main Controller controls all modules required to print, that is, LSU, HVPS, SMPS, FAN, Fuser, FAX
,Scanner etc.
The Main Controller receives print data from the host through network or USB Port or fax, Scanner. It takes
this information and generates printable video bitmap data. Engine and Video Controller are not separated.
2-22
The Main Controller adopts the Chorus3(360MHz) CPU, on board DDR2 memory and external memory to
perform printing and Scan jobs successfully.
The OPE Controller displays the status of the system using 16 x 2line LCD in response to user actions or the
Main controller.
The HVPS supplies high voltage for developing Process. High Voltage controlled by PWM signal from CPU.
SMPS makes +5V and +24V DC from 220V or 110 AC.
2-23
The SCX-483xFR/563xFR/573xFW Electrical Circuit System consists of the following:
• Main Controller
• OPE Controller
• DDR2 SODIMM(Option)
• WLAN Module(only SCX-573xFW)
• SCF(Option)
• SMPS
• HVPS
Diagram of the SCX-483xFR/563xFR/573xFW Electrical Circuit
Scanner
DADF SPEAKER
CLX-4833FR/5637FR Home
Sensor
N. C 1 12 N. C
DADF Paper Detect 1 LE D_A NODE
CN(1.5m m)
2 GND GND 2 11 GND

Sensor
SE NSOR
3 nSENS_DADF_ P_DET GND 3 10 GND BUZZER

OPE _LCD
CN(1.5mm)
4 LE D_A NODE DA DF_RE GI_S OL 4 9 DA DF_RE GI_S OL

DADF Cover Open
CN(1. 5mm )
5 GND DA DF_MODULE _DE T 5 8 N. C

Sensor
6 nSENS_DADF_ COVER_OPEN
nS E NS_DA DF_P _DE T 6 7 nS E NS_DA DF_P _DE T LCD (4-Line)
ADF_JOINT
7 N.C
nS E NS_DA DF_P _RE GI 7 6 nS E NS_DA DF_P _RE GI
DA DF_MOT _S LE E P 8 5 DA DF_MOT _S LE E P
DADF Paper Pos 1 LE D_A NODE
KEY PANEL (CLX -5737FW)
CN(1.5m m)
2 nE N_DA DF_MOT 9 4 nDA DF_MOT _E N

GND
SE NSO R
Sensor
3CH CIS
3 nSENS_DADF_ P_POS DA DF_MOT _P LS 10 3 DA DF_MOT _P LS
4 LE D_A NODE DA DF_MOT _CURRE NT 11 2 DA DF_MOT _CURRE NT
DADF Paper Regi GND CN(1.5mm)
MODEM LSU
1
2
5 DA DF_MOT _DIR 12 1 DA DF_MOT _DIR
Sensor 6 nSENS_DADF_ P_REGI
1
2
1
2
3
GND 1 11 GND Scan CLX -5737FW
S CANNER_HOM E
CN(2mm) CN(1.5mm) CN(2mm)
2
(Dual Beam )
PICKUP
GND 10
nSENS_ DADF_ COVER_OPEN
GND
GND
nDADF_M OT_E N
DADF_M OT_DI R
GND
GND
nDADF_M OT_S LEE P
DADF _MOT_P LS
nSE NS_DA DF _P_P OS
24V
5V
nS ENS _DADF_P _DET
DADF _MOT_CURRENT
nS ENS _DADF_P _REG
DA DF_REGI _SOL
DA DF_PI CKUP _SOL
DA DF _MOT_M S1
DA DF _MOT_M S2
DA DF_EX I T_SOL
DADF Pick up (Conexant )

SOL
1 24V GND
Motor
SOL
DA DF_P ICK UP_S OL 3 9

CN(1.5mm)
2 DA DF_P ICK UP_S OL DA DF_P ICK UP_S OL

Clutch
OPE(CLX-4833FR/5737FR)
nSENS_ DADF_COVER_OPEN 4 8 nSENS_DADF_COVER_OPEN
CN(1.5m m)
GND
GND
GND
nRD
nWR
N. C
3. 3V _LS U
GND
V DO _1_N
GND
GND
V DO _2_N
GND
nLD_O N
LD_P OWE R
N. C
nREA DY _LS U
19 nLSU_M OT_E N
GND
nHsy nc
5V
K EY CLI CK
3. 3V
3. 3V
V DO_1_P
V DO_2_P
24V S
nCS _MO DE M
nI NT_MO DE M
HOOK _DET
nM _RE S ET
17 CLK_LS U_MOT
DAT A7~
A DDR1~
~DA TA0
~A DDR7
nRING0
nS H_1
nS H_2
nS E NS_DA DF_P _P OS 5 7 nS E NS_DA DF_P _P OS
DA DF_MOT _MS 1 6
DADF Regi 6 DA DF_MOT _MS 1
SOL
LCD DRV B˅D(CLX-5737FW)

1 24V
REGI
SOL
DA DF_MOT _MS 2
MT
7 5 DA DF_MOT _MS 2
GND
Clutch 2 DA DF_RE GI_S OL
24V
5V
8 4 24V
5V 9 3 5V
DADF Exit 1 24V DA DF_E X IT_S OL 10 2 DA DF_E X IT_S OL STEP
SOL
SOL
EXIT
2 N.C S E NS_DA DF_P _S IZE 11 1 S E NS_DA DF_P _S IZE BUZZER

12~
~10
~18
3~
11
19
20
21
22
23
24
25
26
27
28
29
30
10
11
12
13
14
15
16
18
20
21
22
Clutch
10
10
11
12
13
14
15
16
1
2
1
2
3
4
5
6
7
8
9
9
8
7
6
5
4
3
2
1
1
2
3
4
5
DA DF_E X IT_S OL
1
2
3
4
5
6
7
8
9
3
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CN
1 OUT1A USB_IF
ADF MOT
MT
CN(2mm)
2 OUT1B (OPE)
DADF Motor 3 OUT2A
4 OUT2B
STEP
A DDR1~ 12~
~DA TA0 ~10
~A DDR7 ~18
20
19
18
17
16
15
14
13
12
11
10
10
DAT A7~ 3~
10
11
12
13
14
15
16
17
18
19
20
10
11
12
13
14
15
16
GND 11
GND 19
HOOK _DET 20
nCS _MO DE M 21
nRD 22
nW R 23
N. C 24
nRS T_MO DE M 25
nI NT_MO DE M 26
N. C 27
3. 3V 28
3. 3V 29
GND 30
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
3
4
5
6
7
8
9
GND 1
2
3. 3V _LS U
GND
V DO _1_N
GND
GND
V DO _2_N
GND
nLD_O N
LD_P OWE R
N. C
nREA DY _LS U
nLSU_M OT_E N
GND
nHs ync
V DO_1_P
V DO_2_P
24V S
MAIN
CLK_LS U_MOT
nS H_1
nS H_2
GND
GND
nDADF_M OT_E N
DADF_M OT_DI R
GND
GND
B _V I N
GND
G _V I N
GND
R_V I N
GND
SCA N_CT R
LE D_COM MO N
CI S_B LE D
CIS _GLE D
CI S_RLE D
GND
MOD_B UZ ZE R_CON
nDADF_M OT_S LEE P
DADF_M OT_P LS
nSE NS_DADF _P_P OS
24V
5V
OUT1A
OUT1B
OUT2A
OUT2B
3. 3V _CI S
3. 3V _CI S
CI S_S P
CIS _CLK
5V
nS ENS _DADF_P _DET
DADF _M OT_CURRENT
nS ENS _DADF_P _REG
nSENS_DADF_ CO VER_OPEN
DA DF _REGI _SOL
DA DF_PI CKUP _SOL
DA DF _MOT_M S1
DA DF _MOT_M S2
DA DF_EX IT _SOL
SCA NNE R_HOME
KE YCLI CK _CON
nRS T_P ANE L
nPOWE R_SW
3.3V 3.3V_Cover_Open
PA NEL_RX D
PA NEL_TX D
CN(FFC 1mm) CN(FFC 1mm) CN(FFC 1mm)
GND
GND
GND
CN(2mm )
Front Cover SCAN_MTR CIS _IF MODE M_IF LS U_IF
Micro Switch CN(1.5mm) CN(1.5mm )

OP E I/F
A DF_IF 24V 1
24V 2
24V 3
3.3V 4
24V S
GND
12
11
24VS 1
2
24V S
GND EEPROM
3.3V 5
DDR2
3.3V 6
THV_RE A D 10 3.3V 3 THV _RE A D
M24C32
CN(1.5mm)
nRS T_S CF 7
CN(1.5mm)
nTHV_E N 9 4 nTHV _E N
HVPS
SCF_IF
SDRAM
5 P WM _THV S CF_TX D 8
P WM_THV 8
(M24C256) S CF_RX D 9
HVP S
P WM_DE V_DC 7 6 P WM _DE V_DC

N. C 10
Supply P WM_MHV
P WM_FUS E R_B IA S
6
5
7
8
P WM _MHV
P WM _FUS E R_B IA S (256MB) nS CF_OP T 11
GND 4 9 GND N. C 12
DEV GND 3 10
11
GND
3. 3V
N. C 13
3.3V 2 GND 14
THV 3.3V _Cover_Open 1 3.3V_Cover_Open1 12 3. 3V_Cov er_Open1 GND 15
GND 16
OPC MHV GND 17
GND 18
NOR FLASH
M AI N FA N
CN(2mm )
1
2
GND
GND
(32MB) GND
1
2
Varistor 3 24V S VCLK
MDI_P 3
3
MDI_M 3
CN NETWORK_IF
4
S
FAN
CHORUS4 25MHz
MDI_P 2
MDI_M 2
5
6
M
MDI_P 1
D C
MDI_M 1
7
MAIN USB CLK 8

MDI_P 0
FUSER 9
CN(2mm )
1
R
GND MDI_M 0
10
CRUM
BIAS DRUM
2 CLK
DIO
3.3V
11
U
3
Clock LE D1
4 3.3V _CRUM
Generator Network 3.3V
12
13
M
NP C_LE D
RTL8211D
14
ASM3P2863 A MAIN CLK
SM PS F AN
CN(2m m)
T FAN V B US 1
USB_IF
1 24V S
DEVELOPER Unit 2 GND DM 2
CN
SMPS DP 3
12MHz
GND 4
USB 2.0
CN(1. 5mm )
USB HUB USB HUB

S MP S FAN
FAN
1 24V S
2 NC
GND
MIDDLE 3
SMPS GND
24V OFF
1
2
24VS 5 GND CN(2mm) CN(2mm) CN
S MP S
CN CN CN
CN(2mm)
CN(2 mm) CN(1.5 mm) CN(2mm )

CN(2mm ) CN(1. 5mm )
CN
Relay 3 4 24V OFF P_EXIT P_SIZE AIR

MAIN MOTOR SENSOR USB_IF
S MP S
CN(2 mm) MP E raser

SENSOR SENSOR TEMP USB_IF USB_IF USB_IF
Fus er ON 5 24V S
2
3.3V_C_OPEN1
3.3V_C_OPEN2
nSENS_BIN_ FU LL
P EA PE R_EX IT
E RA SE R_LED
1 Fus er ON
MO T_REA DY
MO T_BRE AK
FE ED_S ENS
FUSER ON
REG I_S ENS
Pi ck up_CLT
PW M_MO T
MP _SE NS
THE RM_1
Regi_CLT
A MB IE NT
MO T_DIR
WA KE UP
P _E mpt y
MP _CLT
MO T_EN
3.3V_Cover_Open2
3.3V PS
3.3V S
3.3V S
S ENS
3.3V S
3.3V S
V BUS
VB US
V BUS
V BUS
V BUS
24VS
(3. 96mm )
GND
GND
GND
GND
GND
GND
GND
GND
GND
24VS
24VS
24VS
24VS
2
GND
GND
GND
GND
GND
GND
GND
3.3V
GND 2 GND
S MP S
DM
SM PS
DP
DM
DM
DM
DM
CN
CN
5V
DP
DP
DP
DP
24V 1 3 3 24V 1
24V
GND 4 4 GND
24V 2
1
2
10
11
12
13
14
1
2
3
4
5
1
2
3
1
2
3
4
5
1
2
3
4
5
6
7
8
9
1
2
1
2
1
2
3
4
5
24V 2
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
3
4
5
6
7
8
1
2
3
4
5
5 5
5V_SMPS
INLET FUSER
Thermistor1 CL SOL SOL

Ambient OPE I/F
10
9
8
7
6
5
4
3
2
1
Temp
ERASER Sensor
Regi MP MP Exit Paper Cover
Pickup EMPTY REGI FEED LED
Clutch Clutch Sensor Sensor Outbinfull Open
Clutch Sensor Sensor Sensor FDI Flash Direct WLAN
Sensor CLX-5737FW
ThermoStat
FUSER Unit MT Drive USB
BLDC CLX-5637FR
CLX -5737FW
Main Rainier Hardware Team

INLET Motor R&D Group 2
Samsung Electronics
100405
The Main Controller controls all modules required to print, that is, LSU, HVPS, SMPS, FAN, Fuser, etc.
The Main Controller receives print data from the host through network or USB Port. It takes this information
and generates printable video bitmap data. Engine and Video Controller are not separated.
2-24
The Main Controller adopts the CHORUS4(600MHz) CPU, on board DDR2 memory and external memory to
perform printing jobs successfully.
The OPE Controller displays the status of the system using 16 x 4line LCD(SCX-483xFR/563xFR model)
or 4.3” TFT LCD(SCX-573xFW model ) in response to user actions or the Main controller.
The HVPS supplies high voltage for developing Process. High Voltage controlled by PWM signal from CPU.
SMPS makes +5V and +24V DC from 220V or 110 AC.
WLAN module is used for wireless communication(SCX-573xFW model).
2-25
Circuit Board Locations
The following diagrams show the locations of the printer circuit boards:
WLAN
(Only SCX-573xFW)
FAX
HVPS
SMPS
Main Controller
2-26
2.2.5.1 Main controller
SCX-483xFD/HD Main Controller is composed with below components

-. CHORUS3 : To generate the printable video data and control engine
Embedded USB2.0 device
-. On board DDR2 SDRAM : system memory(128MB)
External DRR2 SO-DIMM : 256MB
-. Ethernet PHY : 10/100 Network printing
-. NOR Flash : 16MB for Program memory
-. Serial Flash: 8MB For Fax Data
The Main Controller manages an Electro-photography system, controls the Video Data of printing images
from Main Board to LSU, provides high-voltages and PWMs, adjusts temperature in the fusing system, reads
sensor signals and controls SCF option.
The Main controller also controls OPE and N/W PHY [Network], USB Device.
Rainier 31
Block Diagram
2010 .007 .12
LD power Ambient THV read Fuser
thermistor
RTC Serial Flash (8M) Flash (16M)

MAINBOARD
battery for FAX for OS
Modem
Speaker
DAC RTC ADC SPI Flash Conexant
Power S/W
OPE 2line Home
UART x 4 Buzzer , Power S/W Sensor
Debug
CPU: Chorus 3 I2C x 2
EEPROM(64K)
1 BLDC Motor
Clock : 360Mhz SCF
(Rst,Rx,Tx,REQ)
PHY IC 10/ 100
MAC 540?
PWM x 12 AC201A1KMLG LAN
DDR2 LSU SCAN NCRUM

GPIO USB 2.0
controller controller IF / AFE
Engine (TBD)
DCDC 3.3V
- Solenoid ? ST1S10 system
(MP,Pickup ,Regi)
DDR2 128 M ISP1582 STEP
- Sensor ? ONBOARD + 5V DCDC 1.8V
UR5596
0.9V A3983
(Exit, Feed, Empty , S MP S ST1S10 DDR VTT
256 MB
Regi,Out bin full , MP,
ADF_DET, ADF_POS, 1 DIMM DCDC 1.0V
ADF_COVER, Duplex) ST1S10 CHORUS 3 LAFE1001
H/ W
STEP
- Fan (Main, USB Device USB HOST A3983
SMPS,MIDDLE) PROTECT
HVPS Board LSU

(MHV,THV,DEV_DC SMPS(TYPE2) ADF Unit CIS Scan Unit
,FUSER_BIAS) 24V, 5V, FDB, Relay 2BEAM
Cover S/ W
[ Main Controller Diagram ]
2-27
SCX-483xFD/HD Main Controller Printed Circuit Board Assembly
1 2 3 4 5 6
9 10 11
7
8
12
26
13
25
14
24 15
23 16
22
21 20 19 18 17
● Connection
1 USB HOST 14 N/W
2 FAX 15 USB Device
3 Outbin Full Sensor & Rear Cover 16 Parallel Option DC supply jack
4 CRUM 17 Exit Sensor
5 THERMISTOR 18 Air temp
6 FAN Middle 19 FAN SMPS
7 FAN Main 20 Main Motor & Clutch
8 HVPS 21 SCF
9 Paper Empty, Regi, Feed sensor 22 DDR2 Dimm
10 OPE 23 SMPS Signal
11 CIS 24 SMPS Power
12 ADF 25 MP
13 Scan Motor 26 LSU
● Information
- SEC-CODE : JC92-02351A
- PBA Name : PBA-MAIN
2-28
SCX-483xFR/563xFR/573xFW Main Controller is composed with below components

-. CHORUS4 : To generate the printable video data and control engine
Embedded USB2.0 device, Host channel
-. On board DDR2 SDRAM and external DDR2 SO-DIMM : system memory
On board DDR2 : 256MB
External DRR2 SO-DIMM : 512MB
-. Giga Ethernet PHY : Network printing
-. Nor Flash(32MB) : Program memory
-. Engine Controller(LEPC1) : ADC, DAC, Clutch, Fuser control
The Main Controller manages an Electro-photography system, controls the Video Data of printing images
from Main Board to LSU, provides high-voltages and PWMs, adjusts temperature in the fusing system, reads
sensor signals and controls SCF option.
The Main controller also controls OPE and Giga N/W PHY [Network], USB Device, Wireless Module.
Rainier
SCX-4833FR,SCX-5637FR,SCX-5737FW
skG h {o}G
m Block Diagram V0.3
2010.09.30
o}wzGi
Oto}S{o}Skl}kj
Sm|zlyiphzP
jGzV~ kkyYGY\]tG
swljX
vuivhykG y{jG

mOZYtP
Gvz
thpuivhyk
R
l \XYtiGkpttG
TzGf tG
Otw SwSyP z
kkyYG y{j j
m zwp

l oGz
Power S/W vwlMsjkGky}
TzGf i¡¡GSGwGzV~
OlSGmSGl SG w~tGG [ |hy{GG[
[ssjk
ySvGGSGtwSG
hkmkl{SGhkmwvzSG
hkmjv}lySGkP
nwpv
CPU: Chorus [ llwyvt
[UZIG{m{Tsjk
OZYriGG ][riP
Tm
OtS ztwz SGtpkkslP
Clock: ]WWMhz pYjGGY k r Gw
i¡¡SwGzV~
sz|G PHY IC n

thj zjmG\[Wf
sz| Yilht RTL8211D shu OySyS{SylxP
zjhu z{lw
t |ziGYUWG pmGVGhml LAFE1001
XGiskj hZ`_Z ujy|t
DCDC 3.3V
ST1S10 system
oV~
wyv{lj{ |ziGo|i |ziGo|i
DCDC
24VS1 5V ST1S10
1.1V
CHORUS 4 ns_\Wn ns_\Wn jpzGzG|
zGt OXP
1.8V
DDR2
DCDC
24V2 24V1
5V ISL88550 hkmG|
SMPS A 0.9V ztSzO[P
VTT
SjOZP
|zi |ziGovz{OZP |ziGovz{OYP zjT[_ZZmy

ztwzO{wlYP ztwzO{wlZP k T mkp T ~shu
Y[}SG\}ztwzS T [nG|ziGmG T [UZIG{m{Tsjk zjT\]Z^my
Y[}XSY[}YSG\}ztwzS
mkiSGy mkiSGy T kGw
zjT\^Z^m~
[ Main Controller Diagram ]
2-29
SCX-483xFR/563xFR/573xFW Main Controller Printed Circuit Board Assembly
● Connection
2 3 4 5 6 1 USB HOST
7 2 FAX
8 3 Paper Empty, Regi, Feed sensor
1
4 Out FULL SENSOR & Rear Cover
9 5 Fuser
11 12 6 CRUM
10
13 7 FAN Middle
8 HVPS
14
16 17 9 USB OPE
10 WLAN
15 11 OPE
12 CIS
13 DADF
18 19
14 FAN Main
15 LSU
20 21 16 Scan Motor
17 EDI
22 18 MP
23 24 19 Ethernet
25 20 SMPS Power
21 USB Device
22 Parallel Option DC supply jack
26 27 23 SMPS Signal
28 24 DDR2 SODIMM
29
30 25 Debug
26 Exit Sensor
27 FAN SMPS
● Information
28 SCF
- SEC-CODE : JC92-02350B 29 Main Motor
- PBA Name : PBA-MAIN
30 Air temperature
2-30
2.2.5.2 OPE Controller
The OPE Controller is composed of an OPE MICOM, two status LED, ECO LED, power LED,MODE LED
ANIMATION LED, WPS LED(SCX-573xFW model only), 16x2 line LCD(SCX-483xFD), 4Line LCD(SCX-
483xFR/563xFR), 4.3inch TFT LCD(SCX-573xFW), and some keys.
OPE communicates with main controller via UART/USB(SCX-573xFW).
Diagram of OPE Controller
OPE_TX LED
LED INDICATOR
INDICATOR
OPE_RX STATUS
C
C PP U
U MODE
CHORUS3/ OPE_RST
CHORUS3/
CHORUS4
CHORUS4 USB
OPE
OPE MICOM
MICOM ANIMATION
POWER
(STM8Sp103K3MAFTR)
(STM8Sp103K3MAFTR)
(S3C828B)
(S3C828B) ECO
(S3C2415XH-40))
(S3C2415XH-40 WPS
LCD
LCD DISPLAY
DISPLAY
VHX1620BHRC9(2Line)
VHX1620BHRC9(2Line)
VHF12642(4Line)
VHF12642(4Line)
LMS430HF14(4.3inch
LMS430HF14(4.3inch TFT)
TFT)
KEY
KEY INPUT
INPUT
OPE Controller PBA
● Information ● Information ● Information
• SEC-CODE : JC92-02352A • SEC-CODE : JC92-02366A • SEC-CODE : JC07-00012A

• PBA Name : PBA-OPE(2Line) • PBA Name : PBA-OPE(4Line) • PBA Name : LCD(4Line)
for SCX-483xFD for SCX-483xFR/563xFR
2-31
● Information ● Information ● Information
• SEC-CODE : JC92-02324B • SEC-CODE : JC07-00017A • SEC-CODE : JC92-02365A

• PBA Name : PBA-OPE MAIN • PBA Name : LCD (4.3 inch TFT) • PBA Name : PBA-OPE KEY
(GUI) for SCX-573xFW SUB
2.2.5.3 WLAN (Only SCX-573xFW model)
The Wireless LAN Module supports 802.11b/g/n at only SCX-5737FW model via USB 2.0 high speed. The
Module is installed at the USB Host Channel of Main Controller PBA.
● Information
- PBA Name : PBA-WNPC
2-32
2.2.5.4 SO-DIMM PBA - Optional
The SO-DIMM PBA is the system Memory module of the Main Controller. It is used for the operating system,
some system application programs, and it stores some print data from the USB and Network port. There are
two kinds of SO-DIMM PBA:
• 256MB capacity (SCX-483xFD)

● Information
- SEC-CODE : JC92-01975A 256MB

- PBA Name : PBA RAM DIMM
• 512MB capacity (SCX-483xFR/563xFR/573xFW)
● Information
- SEC-CODE : JC92-02087B 512MB

- PBA Name : PBA MAIN-DIMM
2-33
2.2.5.5 SCF PBA - Optional
The ADF SUB PBA(SCX-483xFD) is the Joint Board to Connect between ADF Module and Main board.
● Information
SEC-CODE : JC92-02387A
PBA Name : PBA-ADF
The JOINT PBA(SCX-483xFR/563xFR/573xFW) is the Joint Board to Connect between DADF Module and
Main board.
● Information
PBA Name : PBA-JOINT(DADF)
2.2.5.6 SCF PBA - Optional
The SCF PBA is the SCF control board. It use UART communication with main controller.
S3F443FX is used as a microcontroller.
● Information
PBA name : A/S ASSY-PBA SCF MAIN
2-34
2.2.5.7 CRUM PBA
CRUM PBA use I2C communication with main Controller.
● Information
PBA Name : PBA-TONER CRUM
2.2.5.8 Connection Part
Controller require connections to all of the system units such as the BLDC motor, Clutch, Sensor, and other
PBAs(OPE, HVPS, SMPS). The Main Controller contains various types of connectors, to deliver electronic
signals through signal wires. The signal wires provide electronic control signals that are used for starting and
stopping the motors, operating clutches, sensing the unit status, etc.
2-35
2.2.5.9 SMPS Board
The SMPS (Switching Mode Power Supply) Board supplies electric power to the Main Board and other
boards through a Main Controller. The voltage provided includes +5V, and +24V from a 110V/220V power
input.
■ SCX-483xFD/HD
3
1
4
● Specification ● Information
110V 220V
General Input/Output Voltage SEC CODE JC44-00095D JC44-00096D
1) AC 110V (90V ~ 135V)
PBA NAME SMPS V1 SMPS V2
2) AC 220V (180V ~ 270V)
3) Output Current:
● Connection
-.+5V : 1.6A
-.+24V : 1.8A
1 INPUT_AC
3) Output Power:
2 Fuser_AC Output
-.+5V : 8.16W
-.+24V : 43.2W 3 SMPS Control Signal (from Engine PBA)
5) Heat Lamp Capacity : 850W 4 OUTPUT_5V&24V (to DC POWER PBA)
2-36
■ SCX-483xFR/563xFR/573xFW
1
4
● Specification ● Information
110V 220V
General Input/Output Voltage SEC CODE JC44-00097E JC44-00090E
1) AC 110V (90V ~ 135V)
PBA NAME SMPS V1 SMPS V2
2) AC 220V (180V ~ 270V)
3) Output Current:
● Connection
-.+5V : 2.4A
-.+24V : 3.0A
1 INPUT_AC
4) Output Power:
2 Fuser_AC Output
-.+5V : 12W
-.+24V : 72W 3 SMPS Control Signal (from Engine PBA)
5) Heat Lamp Capacity : 850W 4 OUTPUT_5V&24V (to DC POWER PBA)
2-37
2.2.5.10 HVPS Board
The SCX-483x / 5x3x series contains a High Voltage Power Supply(HVPS) board.
This board generates high-voltage channels which includes MHV, DEV, BLADE, SUPPLY, OPC, THV and
FUSER BIAS.
8 1
2 3 4 5
7
6
● Connection
1 Main Interface 5 SUPPLY(-489V)

2 MHV(-1240V) 6 OPC(-51V)
3 DEV(-338V) 7 THV(+1315V, -1000V)
4 BLADE(-389V) 8 FUSER BIAS(240V)
● Information
- PBA Name : HVPS
2-38
2.2.5.11 HVPS Board
The SCX-483x / 5x3x series contains a FAX board.The Modem Card is used to transfer and receive FAX
data through a telephone line. This PBA is controlled by the Main PBA and has two connectors, one for the
telephone line connection and the other for an external phone connection.
2
5
3
● Connection
1 Main Interface
2 Speaker
3 Hook(only China)
4 Tel Line
5 Ext Line
● Information
: JC92-01746C (only China)
- PBA Name : SFX336 MODEM FAX MODULE
2-39
2.2.5.10 Electrical Parts Location
S7
S6
C3 M1
S5
F1 F2
C2
S3
C1
S2 S4
F3
S1
Sensor Part Description Part Code

M1 Main motor MOTOR BLDC JC31-00144A
C1 MP Pick up clutch CLUTCH-ELECTRIC JC47-00034A
C2 Cassette Pick up clutch CLUTCH-ELECTRIC JC47-00033A
C3 Regi clutch CLUTCH-ELECTRIC JC47-00033A
S1 Cassette paper empty sensor PHOTO-INTERRUPPTER 0604-001393
S2 MP paper empty sensor PHOTO-INTERRUPPTER 0604-001393
S3 Regi sensor PHOTO-INTERRUPPTER 0604-001393
S4 Feed sensor PHOTO-INTERRUPPTER 0604-001393
S5 Exit sensor PHOTO-INTERRUPPTER 0604-001393
S6 Outbin full sensor PHOTO-INTERRUPPTER 0604-001393
S7 Home position sensor PHOTO-INTERRUPPTER 0604-001415
F1 Middle fan FAN JC31-00146A
F2 Main fan FAN JC31-00146A
F3 SMPS fan FAN JC31-00108A
2-40
2.2.6 Engine F/W Control Algorithm
2.2.6.1 Feeding
If feeding from a cassette, the drive of the pickup roller is controlled by controlling the solenoid. The on/off
of the solenoid is controlled by controlling the general output port or the external output port. While paper
moves, occurrence of Jam is judged as below.
ITEM Description
- After picking up, paper cannot be entered because paper is not fed.
- After picking up, paper entered but it cannot reach to the feed sensor in certain time
JAM 0 due to slip, etc.
- After picking up, if the feed sensor is not on, re-pick up. After re-picking up, if the feed
sensor is not on after predetermined period of time, it is JAM 0.
- After the leading edge of the paper passes the feed sensor, the trailing edge of the
paper cannot pass the feed sensor after predetermined period of time.
JAM 1 - After the leading edge of the paper passes the feed sensor, the paper cannot reach
the exit sensor after predetermined period of time.
*The paper exists between the feed sensor and the exit sensor.
- After the trailing edge of the paper passes the feed sensor, the paper cannot pass the
JAM 2
exit sensor predetermined period of time.
2.2.6.2 Transfer
The charging voltage, developing voltage and the transfer voltage are controlled by PWM (Pulse Width
Modulation). The each output voltage is changeable due to the PWM duty. The transfer voltage admitted
when the paper passes the transfer roller is decided by environment conditions. The resistance value of the
transfer roller is changed due to the surrounding environment or the environment of the set, and the voltage
value, which changes due to the environments, is changed through AD converter. The voltage value for
impressing to the transfer roller is decided by the changed value.
2-41
2.2.6.3 Fusing
The temperature change of the heat roller’s surface is changed to the resistance value through the use of a
thermistor.
The Main Bd uses the resistance value of the Thermistor and converts it to a voltage value through the use
of an AD converter, the temperature is decided based on the voltage value read. The AC power is controlled
by comparing the target temperature to the value from the thermistor. If the value from the thermistor is out of
controlling range while controlling the fusing, the error stated in the below table occurs.
• Open Heat Error
When the engine operates the warm-up process, if the temperature of the fixing unit is not higher than a
specified temperature, the engine defines Open Heat Error. When this error is detected, the engine stops
all functions and keeps the error state. Also, the engine informs the error status of the main system, so it can
take appropriate action; and then the error message is displayed at LCD window or LED informing the error
status of the user.
• Low Heat Error
When the engine is at stand-by, printing or warm-up mode, if the temperature of the fixing unit is lower than
the specified temperature at each state and the lower temperature state is maintained during the specified
time, the engine defines Low Heat Error. When this error is detected, the engine stops all functions and
keeps it at the error state. Also, the engine informs the error status of the main system, so it can take
appropriate action; and then the error message is displayed at LCD window or LED informing the error status
of the user.
• Over Heat Error
For overall engine state, if the temperature of the fixing unit is higher than the specified temperature and the
temperature state is detected for a specific duration, then the engine defines Over Heat Error. When this
error is detected, the engine stops all functions and keeps it at the error state. Also, the engine informs the
error status of the main system, so it can take appropriate action; and then the error message is displayed at
LCD window or LED informing the error status of the user.
2-42
2.2.6.4 LSU
LSU receives the image data from PVC or HPVC and make the latent image on OPC surface.
It uses the single beam, LD. The errors related to LSU are as follows:
• By Lready
When the printing is started, the engine drives the polygon motor of LSU. After the specified time is elapsed,
if the motor is not in a ready status, the engine detects the error that the polygon motor is not in a ready
status. If this error happens, the engine stops all functions and keeps it at the error state. Also, the engine
informs the error status of the main system and the error message is displayed at LCD window to inform the
error status of the user.
• By Hsync
When the polygon motor is ready, the LSU sends out the signal called Hsync and used to synchronize with
each image line. So, if the engine does not detect consecutively the signal for a fixed time, it defines the
Hsync Error. If this error happens, the engine stops all functions and keeps it at the error state. Also, the
engine informs the error status of the main system and then the error message is displayed at LCD window
to inform the error status of the user. LSU Error Recovery: If the LReady or Hsync error happens, the paper
is exited before the error code is initiated. The engine mode is changed to recovery mode and the engine
informs the main system of the engine mode. And the engine checks the LSU error. If the error doesn’t
happen, the printing job.
2-43
2.2.7 S/W Descriptions
2.2.7.1 Overview
The software of SCX-483x/5x3x series system is constructed with

1) Host Software part that the application software operated in Window and Web Environment, and
2) Firmware parts that is a Embedded software controls printing job.
2.2.7.2 Architecture
Host Software is made up of

1. Graphic User Interface that offers the various editing functions to user in Host,
2. Driver that translates the received document to a Printing Command language which printer can
understand and transfers data to spooler,
Printer /MFP
HOST
Firmware
Software
Web-based Stand-alone Application

Driver Kernel
Application Application (Emulation)
3. Stand-alone Application that offers the various printing application, PSU(Printer Settings Utility), Printer
Status Monitor, Network Management in Window system,
4. Web-based-Application that offers the same functions as Stand-alone Application and RDC(Remote
Diagnosis Control) in Web environment.
Firmware is made up of
1. Application (Emulation) that is a interpreter translate data received from Host to a printing language
(PCL, PS, GDI, etc.) to be able to make the user to take same output as originally one what composed in
Host.
2. Kernel that control and management the whole procedure include of Control flow and Printing Job before
transfer to Engine system.
2-44
2.2.7.3 Data and Control Flow
Host Firmware
USB
Driver
- PCL3, PS3 3
R KERNEL
Web-based U
- Document Management
W
System Engine
- Network Administration 0 Network
R
- Status Monitor
Interface
Application
- Remote Control Panel
Q
L
Stand-alone
W
R Application
(Emulation)
- Printer Setting Utility
U - PCL
- Network Administration - PS3
- Status Monitor
The above Block Diagram is explained that:
Host Side is made up of :
1. Driver that is Windows application software translate printed data to one of printer language and create
spooler file.
2. Web-based Application that offer a various printer additional functions, management of printing job,
printer administration, Status monitor to monitoring the printer status by real time in Web, independent
environment on OS.
3. Stand-alone Application that is a similar Window software as same as above 2,
4. Port Monitor that manages the network communication between spooler and Network Interface Card, or
various additional application and Network Interface Card,(this is, at first, make communication logical
port, manage the data, transfer them from spooler to network port, and offer the result of printing).
2-45
Firmware Side is made up of :
1. Network Interface Application is that relay the communication between Host and kernel using various
network protocol.
2. Kernel is that manages the flow control of emulation procedure, receiving data from Host or Network
application and printing with engine & rendering job,
3. Emulation is that interprets the various output data from selected emulation,
4. Engine is that prints rendered bit-map data to paper with required size and type by Kernel.
And then, for Job Spooling function for Multi-User, Multi-Printing that is occurred in Network printing and
various additional printing functions, this Kernel uses max. 10 Queuing systems in a memory.
In Printing, the two procedures are :
(1) Case of using USB Port

- After user start to print the wanted document to PCL string or compressed GDI bit-map data, Driver
translate the all graphic data of it and send data to host spooler. And then the spooler sends the data
stream to the printer via USB port.
- Kernel receives this data from Host, and then select emulation fit to data and start selected one. After
emulation job end, Kernel sends the output bit-map data to Engine using Printer Video Controller (by
clock type for LSU).
- Engine print the received data to required paper with the sequential developing process.
(2) Case of using Network Interface Application

- After user start to print the wanted document to PCL string or compressed GDI bit-map data, Driver
translate the all graphic data of it and send data to host spooler.
- If so, Port monitor managing network port receives data from spooler and sends a data stream to the
Network Interface Application.
- Network interface card receives it and send to Kernel part.
- Kernel receives this data from Host, and then select emulation fit to data and start selected one. After
emulation job end, Kernel sends the output bit-map data to Engine using Printer Video Controller (by
clock type for LSU).
- Engine print the received data to required paper with the sequential developing process.
2-46
3. Disassembly and Reassembly
3.1 General Precautions on Disassembly

When you disassemble and reassemble Releasing Plastic Latches
components, you must use extreme caution. The
close proximity of cables to moving parts makes Many of the parts are held in place with plastic
proper routing a must. latches. The latches break easily; release them
If components are removed, any cables disturbed carefully.
by the procedure must be restored as close as To remove such parts, press the hook end of the
possible to their original positions. Before removing latch away carefully from the part to which it is
any component from the machine, note the cable latched.
routing that will be affected.
Whenever servicing the machine, you

must perform as follows:
1. Check to verify that documents are not stored in

memory.
2. Be sure to remove the toner cartridge before you

disassemble parts.
3. Unplug the power cord.
4. Use a clean at surface.
5. Replace only with authorized components.
6. Do not force plastic-material components.
7. Make sure all components are in their proper

position.
3-1
3.2 Screws used in the printer

The screws listed in the table below are used in this printer. Please ensure that, when you disassemble the
printer, you keep a note of which screw is used for which part and that, when reassembling the printer, the
correct screws are used in the appropriate places.
Part Code Location Description Qty
6003-000196 SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 20
6003-000261 FRAME MAIN SCREW-TAPTYPE;BH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,- 2
6003-000269 SCREW-TAPTYPE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,- 3
6002-000440 DUPLEX SCREW-TAPPING;PWH,+,2,M3,L8,ZPC(BLK),SWRCH18A 5
6003-000196 MP SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 2
6003-000269 FUSER SCREW-TAPTYPE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,- 3
6003-000282 SCREW-TAPTYPE;BH,+,-,B,M3,L8,ZPC(BLK),SWRCH18A,- 4
6003-000269 DRIVE SCREW-TAPTYPE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,- 6
6003-000261 SCREW-TAPTYPE;BH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,- 3
6003-000264 SCREW-TAPTYPE;PWH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,- 2
FRAME-ETC
6003-000301 SCREW-TAPTYPE;BH,+,S,M4,L6,ZPC(WHT),SWRCH18A 1
6003-001474 SCREW-TAPTYPE;BH,+,B,M3,L30,ZPC(WHT),SWRCH18A 2
6006-001078 SCREW-TAPTYPE;PH,+,WSP,B,M3,L10,ZPC(WHT),SWRCH18A 1
6003-000282 LSU SCREW-TAPTYPE;BH,+,-,B,M3,L8,ZPC(BLK),SWRCH18A,- 5
6003-000196 COVER-MIDDLE SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 4
6003-000264 COVER-FRONT SCREW-TAPTYPE;PWH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,- 2
6003-000264 MP GUIDE-TRAY SCREW-TAPTYPE;PWH,+,-,B,M3,L6,ZPC(WHT),SWRCH18A,- 1
6003-000282 CARTRIDGE TONER SCREW-TAPTYPE;BH,+,-,B,M3,L8,ZPC(BLK),SWRCH18A,- 4
6003-000196 MFA SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 2
OPE
6003-000269 SCREW-TAPTYPE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,- 4
6001-000130 SCREW-MACHINE;BH,+,M3,L6,ZPC(WHT),SWRCH18A 1
DADF
6003-000269 DRIVE-DADF SCREW-TAPTYPE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,- 6
6003-000196 DADF-COVER OPEN SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 2
6001-000130 DADF-PLATEN SCREW-MACHINE;BH,+,M3,L6,ZPC(WHT),SWRCH18A 1
6003-000196 DADF-LOWER SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 2
6003-000196 DADF-UPPER SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 3
6003-000196 PLATEN SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 5
6003-000196 PLATEN-UPPER SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 4
6003-000196 PLATEN-LOWER SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 8
6003-000196 PLATEN-A4 MIDDLE SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 3
6003-000269 ELA UNIT-SCAN DRIVE SCREW-TAPTYPE;BH,+,-,S,M3,L6,ZPC(WHT),SWRCH18A,- 2
6003-000196 MAINLNE SCREW-TAPTYPE;PWH,+,B,M3,L10,NI PLT,SWRCH18A 20
3-2
3.3 Disassembly procedure
3.3.1 Cover
1. Remove the cassette. 3. Remove the duplex unit.
4. Open the rear cover and then remove it by

2. Remove the front cover by releasing both hooks. releasing both hooks.
3-3
5. Remove the left cover. 6. Remove the right cover.
3-4
3.3.2 Scanner Assy
1. Remove all covers. (Refer to 3.3.1) 3. Unplug 3 connectors.

2. Remove 5 screws. (Right x 1, Rear x 3, Front x 1)
4. Lift up and release the Scanner Assy.
3-5
3.3.2.1 OPE board
1. Open the DADF unit. 6. Turn up OPE Unit.

2. Unplug the connector after removing the
connector cover.
3. Lift up and release the DADF unit.
7. Unplug 2 connectors and remove 7 screws.

8. Release the OPE board.
4. Open the Scanner.

5. Remove 2 screws.
3-6
3.3.2.2 CIS Unit
1. Remove the DADF unit and OPE unit. 4. Unplug the end of the at cable from the CIS,
(Refer to 3.3.2.1) and release the drive belt.
2. Remove 5 screws. 5. Remove the CIS Unit.
3. Release the Platen glass unit.
3-7
3.3.2.3 Scan Motor
1. Remove the DADF unit, OPE unit and Platen 3. Release the scan motor after removing 3 screws.
glass unit. (Refer to 3.3.2.1~2)
2. Remove 4 screws.
3.3.2.4 Home position sensor
1. Remove the Platen glass unit. (Refer to 3.3.2.2)

2. Release the home position sensor after unplugging the connector.
3-8
3.3.3 DADF Unit (SCX-563xFR / 563xHR / 573xFW)
1. Open the DADF unit.

2. Unplug the connector after removing the connector cover.
3. Lift up and release the DADF unit.
3.3.3.1 DADF Pick up unit
1. Remove the DADF-COVER OPEN. 2. Remove the spring. Release the shaft holder.
And then remove the DADF pick up unit.
3-9
3.3.3.2 DADF board
1. Remove 4 screws. 4. Remvoe the DADF rear cover.
2. Release the Original Feed Tray. 5. Remove the DADF board after removing 2
screws and all harness.
3. Remove 3 screws.
3-10
3.3.3.3 DADF Motor
1. Remove 8 screws. 3. Remvoe the DADF rear cover.
2. Release the Original Feed Tray. 4. Remove 2 screws.
3-11
5. Remove the DADF front cover. 8. Remove 1 screw connecting the ground wire.
6. Remove 3 screws. 9. Release the DADF drive unit after removing 3

screws.
7. Remove 2 screws on DADF board.
3-12
3.3.4 ADF Unit (SCX-483xFR/ FD/ HD)
1. Open the ADF unit.

2. Unplug the connector after removing the connector cover.
3. Lift up and release the ADF unit.
3.3.4.1 Tray Input
1. Open the ADF top cover.

2. Pull and release the rear hinge of the Original Feed Tray.
3-13
3.3.4.2 Front / Rear cover
1. Remove 2 screws. 2. Remove the front and rear cover from both
sides.
3.3.4.3 Paper Path Assy
1. Remove the paper path Assy after removing 4 screws.
3-14
3.3.4.4 ADF pick up unit
1. Remove 3 E-rings.
2. Pull the shaft to the direction of arrow.
3. Take off the ADF pick up unit.
3.3.4.5 ADF motor
1. Remove the paper path Assy after removing 4 2. Remove the motor after removing 2 screws.
screws.
3-15
3.3.5 Middle Cover
1. Remove the Scanner Assy. (Refer to 3.3.2) 4. Release 2 hooks from the rear.
2. To remove the middle cover, remove 2 screws,
6 connectors,1 USB cable from the main board.
Hook
5. Lift up and release the middle cover.
3. Remove 4 screws.
3-16
3.3.6 Main board
1. Remove the right cover. (Refer to 3.3.1 Cover)

2. Unplug all connectors on the main board.
3. Remove 4 screws.
4. Release the main board.
3.3.7 HVPS board

2. Remove 5 screws.
3. Unplug all connectors on the HVPS board.
4. Release the HVPS board.
3-17
3.3.8 SMPS board

2. Unplug all connectors on the SMPS board.
3. Remove 4 screws.
4. Release the SMPS board.
3.3.9 Laser Scanning Unit (LSU)
1. Remove the Middle cover. (Refer to 3.3.5 Middle Cover)

2. Unplug 2 at cables from the LSU.
3. Remove 3 screws.
4. Release the LSU.
3-18
3.3.10 Fuser unit

CAUTION
The temperature gets high in the vicinity of the fuser unit. When replacing it, you may get injured. Before
replacing it, make sure that fuser unit has cooled.
1. Open the Frame-Rear by pushing both green 3. Remove the exit sensor holder after removing
points. 2 screws.
4. Remove 4 screws.
CAUTION
When reassembling the fuser unit, do not forget to
tighten these screws.
5. Release the fuser unit.
Frame-Rear
2. Remove the Frame-Rear by releasing both

hooks.
Exit sensor holder
3-19
3.3.11 Main drive unit
1. Remove the left cover. (Refer to 3.3.1 Cover) 4. Unplug the connector from the main motor.
2. Remove the Bar coupler. 5. Release the main drive unit.
Bar coupler
3. Remove the main drive unit after removing

6 screws.
1
3
6
4 2
NOTE
When reassembling the main drive unit, tighten 6
screws in order as shown above.
3-20
3.3.12 Feed drive unit
1. Remove the main drive unit. (Refer to 3.3.11)
2. Release the feed drive unit after removing 2 screws.
3.3.13 Pick up/ Regi/ MP clutch
1. Remove the feed drive unit.
2. For the clutch to require replacement, unplug the connector then replace it.
Regi. MP
Pick-up
3-21
3.3.14 Pick up roller
1. Remove the cassette and duplex unit.
2. Pull the small tap down, then release the pick up roller.
3.3.15 Transfer roller
1. Remove the top cover. 3. Push the transfer roller holder to the center and
(Refer to 3.3.5 Middle Cover) release it.
2. Release the LSU bracket after removing 4. Remove the transfer roller.
Transfer roller
4 screws.
3-22
3.3.16 MP unit
1. Remove the front / middle / right cover. 3. Separate the MP lower from the MP upper.
2. Remove 4 screws.
MP pick up/ forward roller
MP retard roller
3.3.17 Bin-full sensor
1. Remove the top / left cover.
2. Release the bin-full sensor after unplugging the connector.
3-23
3.3.18 Regi. / Feed / Empty sensor
1. Remove the cassette and duplex unit. 4. For the sensor to require replacement, unplug
the connector then replace it.
2. Remove the PLATE-FRAME BOTTOM after
removing 4 screws.
Regi. sensor
Feed sensor
5. Remove the sensor cover after removing

2 screws.
3. Remove the sensor cover after removing 2
screws.
3-24
6. Unplug the connector then release the empty

sensor.
Empty sensor
3.3.19 Cassette roller (Retard roller)
1. Remove the cassette. 3. Release the Retard roller.
2. Open the COVER-CASSETTE.
3-25
4. Alignment and Troubleshooting
4.1 Alignment and Adjustments

This chapter describes the main functions for service, such as the product maintenance method, the test
output related to maintenance and repair, Jam removing method, and so on.
It includes the contents of manual.
4.1.1 Control Panel
■ Type A
X Y Z [ \ ] ^ _ ` XW XX XY XZ
YW X` X_ X^ ] X] X\ X[
Adjusts the brightness level to make a copy for easier reading, when the
1 Darkness
original contains faint markings and dark images.
Allows you to coy both sides the ID card like a driver’s license to a single
2 ID Copy
side of paper.
3 Display screen Shows the current status and prompts during an operation.
4 Copy Activates Copy mode.
5 Fax Activates Fax mode.
Scrolls through the options available in the selected menu and increases
6 Left/Right Arrows
or decreases values.
7 Menu Enters Menu mode and scrolls through the available menus.
8 OK Con rms the selection on the screen.
9 Numeric keypad Dials a number or enters alphanumeric characters.

Allows you to store frequently used fax numbers and email addresses or
10 Address Book
search for stored fax numbers or email addresses.
4-1
Redials the last number in ready mode, or inserts a pause into a fax
11 Redial/Pause
number in Edit mode.
12 Stop/Clear Stops an operations at any time.
Turn the power on or off, or wake up the machine from the power save
mode. Press this button until Power Down appears on the display and
13 Power
choose Yes to turn the power off. You can also turn the power on, or wake
up the machine from power save mode by pressing this button.
14 Status LED Shows the status of your machine.
15 Start Starts a job.

When you press this button, you can hear a dial tone. Then enter a fax
16 On Hook Dial
number. It is similar to making a call using speaker phone.
17 Back Sends you back to the upper menu level.
18 Scan Activates Scan mode.
19 Eco Turn into eco mode to reduce toner consumption and paper usage.
Allows you to directly print les stored on a USB memory device when it is
20 Direct USB
inserted into the USB port on the front of your machine.
4-2
■ Type B
X Y Z [ \ ] ^ _ ` XW XX XY
YW X` X_ X^ X] ] X\ X[ XZ
Adjusts the brightness level to make a copy for easier reading, when the
1 Darkness
original contains faint markings and dark images.
Allows you to coy both sides the ID card like a driver’s license to a single
2 ID Copy
side of paper.
4 Copy Activates Copy mode.
5 Fax Activates Fax mode.

Scroll through the options available in the selected menu, and increase or
6 Arrows
decrease values.
7 OK Con rms the selection on the screen.

Allows you to store frequently used fax numbers and email addresses or
9 Address Book
search for stored fax numbers or email addresses.
Redials the last number in ready mode, or inserts a pause into a fax
10 Redial/Pause
number in Edit mode.
11 Stop/Clear Stops an operations at any time.
12 Power
13 Status LED Shows the status of your machine.

When you press this button, you can hear a dial tone. Then enter a fax
15 On Hook Dial
number. It is similar to making a call using speaker phone.
16 Back Sends you back to the upper menu level.
4-3
17 Menu Enters Menu mode and scrolls through the available menus.
18 Scan Activates Scan mode.
19 Eco Turn into eco mode to reduce toner consumption and paper usage.
Allows you to directly print les stored on a USB memory device when it is
20 Direct USB
inserted into the USB port on the front of your machine.
4-4
■ Type C
X Y Z [ \
XX XW ` _ ^ ]
3 Clear Deletes characters in the edit area.
4 Stop Stops an operations at any time.

5 Power
6 WirelessLED Shows the current status of the wireless network connection.
7 Status Shows the status of your machine.

9 Log out Allows user to log out.
10 Help Gives detailed information about this machine’s menus or status.
11 Reset Resets the current machine’s setup.
4-5
4.1.2 Understanding The Status LED

The color of the Status indicates the machine’s current status.
NOTE
• Some LEDs may not be available depending on model or country.
• To resolve the error, look at the error message and its instructions from the troubleshooting part.
STATUS DESCRIPTION
Status Off • The machine is off-line.
LED Green Blinking • When the backlight slowly blinks, the machine is receiving data from
the computer.
• When the backlight blinks rapidly, the machine is printing data.
On • The machine is on-line and can be used.
Red Blinking • A minor error has occurred and the machine is waiting for the error
to be cleared. Check the display message. When the problem is
cleared, the machine resumes. For some models that does not
support the display screen on the control panel, this feature is not
applicable.
• Small amount of toner is left in the cartridge. The estimated cartridge
life of toner is close. Prepare a new cartridge for replacement. You
may temporarily increase the printing quality by redistributing
the toner
On • A toner cartridge has almost reached its estimated cartridge lifea.
• The cover is opened. Close the cover.
• There is no paper in the tray. Load paper in the tray.
• The machine has stopped due to a major error.
Wireless Blue On When the machine is connected to a wireless network, Wireless LED
LEDb lights on blue.
a. Estimated cartridge life means the expected or estimated toner cartridge life, which indicates the average capacity
of print-outs and is designed pursuant to ISO/IEC 19752. The number of pages may be affected by operating
environment, printing interval, graphics, media type and media size. Some amount of toner may remain in the cartridge
even when red LED is on and the printer stops printing.
b. Wireless model only
4-6
4.1.3 JAM Removal
4.1.3.1 Clearing original document jams
To avoid tearing the document, remove the jammed document slowly and carefully.
Original paper jam in front of scanner
1. Remove any remaining pages from the 4. Close the document feeder cover.
document feeder.
2. Open the document feeder cover.
3. Gently remove the jammed paper from the

document feeder.
4-7
Original paper jam inside of scanner
1. Remove any remaining pages from the 4. Open the document feeder.
document feeder.
5. Grasp the misfeed paper, and remove the paper

from the feed area by carefully pulling it.
3. Gently remove the jammed paper from the
document feeder.
If you see no paper in this area, go to next step. 6. Close the document feeder.
4-8
Original paper jam in exit area of scanner Original paper jam in scanner duplex path
1. Remove any remaining pages from the NOTE - For SCX-4833FR, SCX-4835FR, SCX-
document feeder. 563x Series and SCX-573x Series.
2. Gently remove the jammed paper from the 1. Remove any remaining pages from the
document feeder. document feeder.
3. Open the duplex jam cover.
4-9
4. Pull the jammed paper gently out of the 6. Grasp the misfeed paper, and remove the paper
document feeder. from the feed area by carefully pulling it.
Close the duplex jam cover and the document

feeder cover. If you do not see paper in this area,
go to the next step. 7. Close the document feeder.
5. Open the document feeder.
4-10
4.1.3.2 Clearing paper jams
To avoid tearing the paper, pull the jammed paper out slowly and gently.
In tray1
1. Open and close the front cover. The jammed 4. Insert tray 1 back into the machine until it snaps
paper is automatically ejected from the machine. into place. Printing automatically resumes.
If the paper does not exit, go to the next step.
2. Pull out tray1.
In optional tray2
1. Pull out optional tray 2.
2. Remove the jammed paper from the machine.
3. Remove the jammed paper by gently pulling it

straight out.
If the paper does not move when you pull or if you

do not see the paper in this area, stop and go to
the next step.
3. Pull tray1 half-way out.
If the paper does not move when you pull, or if you

do not see the paper in this area, check the fuser
area around the toner cartridge.
4-11
4. Pull the paper straight up and out. Inside the machine
1. Open the front cover and pull the toner cartridge

out.
5. Insert the trays back into the machine. Printing

automatically resumes. 2. Remove the jammed paper by gently pulling it
straight out.
In the multi-purpose tray
1. If the paper is not feeding properly, pull the

paper out of the machine.
3. Replace the toner cartridge and close the front

cover. Printing automatically resumes.
2. Open and close the front cover to resume

printing.
4-12
In the exit area In the duplex unit area
1. Open and close the front cover. The jammed 1. Pull the duplex unit out of the machine.
paper is automatically ejected from the machine.
If you do not see the jammed paper, go to the

next step.
2. Gently pull the paper out of the output tray.
2. Remove the jammed paper from the duplex unit.
If you do not see the jammed paper or if there is

any resistance when you pull, stop and go to the
next step.
If the paper does not come out with the duplex unit,
3. Open the rear cover. remove the paper from the bottom of the machine.
4. Remove the jammed paper as shown in the

following gure.
3
If you still do not see the paper, go to the next step.
5. Close the rear cover. Printing automatically

resumes.
4-13
3. Insert the duplex unit into the machine.
4. Open the rear cover.
5. Remove the jammed paper as shown in the

following gure.
6. Return the fuser door and the lever to their

original position.
7 Close the rear cover. Printing automatically

resumes.
4-14
4.1.4 Useful menu item for service
a) Monitoring the supplies life.
If you experience frequent paper jams or printing problems, check the number of pages the machine has
printed or scanned. Replace the corresponding parts, if necessary.
NOTE - Accessing menus may differ from model to model
1. Select Menu > System Setup > Maintenance > Supplies Life on the control panel.
2. Select the option you want and press OK.

• Supplies Info: Prints the supply information page.
• Total: Displays the total number of pages printed.
• ADF Scan: Displays the number of pages printed by using the document feeder.
• Platen Scan: Displays the number of pages scanned by using scanner glass.
3 Press (Stop/Clear) to return to ready mode.
b) Printing a report
This product provides several printable reports for maintenance purposes.

These reports can be used to aid the diagnosis of print quality problems.
■ Configuration report (Menu > System Setup > Report > Configuration)
You can print a report on the machine’s overall con guration. It shows various SW version and current
machine setting status.
■ Supplies Information report (Menu > System Setup > Report > Supplies Info.)
You can print supplies’ information page. It shows consumable unit life status and toner using status.
■ Usage Counter (Menu > System Setup > Report > Usage Counter)
You can print a usage page. The usage page contains the total number of pages printed.
c) Maintenance menu
This menu allows you to maintain your machine. (Menu > System setup > Maintenance)
• CLR Empty Msg. : This option appears only when toner cartridge is empty.
• Supplies Info. : This item allows you to check how many pages are printed and how much toner are left in
the cartridge.
• TonerLow Alert : If toner in the cartridge has run out, a message informing user to change the toner
cartridge appears. You can set the option for this message to appear or not.
4-15
d) Altitude adjustment
The print quality is affected by atmospheric pressure, which is determined by the height of the machine
above sea level. The following information will guide you on how to set your machine to the best print quality
or best quality of print.
Before you set the altitude value, determine the altitude where you are.
4,000 m
(13,123 ft)
1
3,000 m
(9,842 ft)
2
2,000 m
(6,561 ft)
3
1,000 m 1 High 3
(3,280 ft) 2 High 2
4 3 High 1
0 4 Normal
1. Ensure that you have installed the printer driver with the provided Printer Software CD.
2. Double-click the Smart Panel icon on the Noti cation Area in Linux. You can also click Smart Panel on
the status bar in Mac OS X.
For Windows user, select Start > Programs or All Programs > Samsung Printers > Samsung Easy
Printer Manager.
3. Click Printer Setting.

If your machine is connected to the network, you can set the altitude via SyncThru™ Web Service.
4. Click Setting > Altitude Adjustment. Select the appropriate value from the drop-down list, and then click
Apply.
You can also set the altitude in System Setup > Altitude Adj. option on the machine’s display.
4-16
4.1.5 Periodic Defective Image
If an image defects appears at regular intervals on the printed-paper, it is due to a faulty or damaged roller.
Refer to the table below and check the condition of the appropriate roller.
4 5
3
2 6 7
1
8
Band Period
No Roller Description Phenomenon Defective part
(mm)
1 1st Pressure roller 62.8 mm Background
2 2nd Pressure roller 37.7 mm Background Fuser unit
3 Heat roller 77.8 mm Black spot and fuser ghost
4 Charge roller 26.7 mm Black spot
5 Developer roller 36.78 mm Horizontal band
Toner cartridge
6 OPC drum 75.49 mm White and Black spots
7 Supply roller 69.57 mm Horizontal band
8 Transfer roller 47.1 mm Ghost, Damaged image
4-17
4.1.6 Using the Samsung Easy Printer Manager program and Smart Panel
Samsung Easy Printer Manager and Smart Panel are a program that monitors and informs you of the
machine status, and allows you to customize the machine’s settings. These programs are installed
automatically when you install the machine software.
To use this program, you need the following system requirements:

• Windows. Check for windows operating system(s) compatible with your machine.
• Mac OS X 10.3 or higher
• Linux. Check for Linux systems that are compatible with your machine.
• Internet Explorer version 5.0 or higher for ash animation in HTML Help.
If you need to know the exact model name of your machine, you can check the supplied software CD.
4.1.6.1 Using the Samsung Easy Printer Manager program (Windows only)
Samsung Easy Printer Manager is a Windows-based application that combines Samsung device settings into
one location. Samsung Easy Printer Manager combines device settings as well as printing environments,
settings/actions, launching applications, and so on. All of these features provide a gateway to conveniently
use Samsung machine. Samsung Easy Printer Manager provides two different user interfaces for the user to
choose from: the default user interface and the advanced settings user interface. Switching between the two
interfaces is easy: just click a button.
Understanding Samsung Easy Printer Manager program

This interface is intended to be used by general device users in a small business or small home of ce
environment.
For Windows user, select Start > Programs or All Programs > Samsung Printers > Samsung Easy Printer
Manager.
The Samsung Easy Printer Manager interface is comprised of various basic sections as described in the
table that follows.
4-18
The Printer List displays icons corresponding to discovered network or local

1 Printer List
printers’ error status.
This area gives you general information about your machine. You can check
information, such as the machine’s model name, IP address (or Port name),
and machine status.
2 Printer Information
Troubleshooting button: This button opens Troubleshooting Guide when
an error occurs. You can directly open the necessary section in the user’s
guide.
Application Includes links for changing to the advanced settings, preference, help, and
3
information about.
Displays Quick links to machine speci c functions. This section also includes
links to applications in the advanced settings.
4 Quick links
If you connect your machine to a network, the SyncThru™ Web Service
window appears.
Displays information about the selected machine, remaining toner level
5 Contents Area and paper. The information will vary based on the machine selected. Some
machines do not have this feature.
Click on the Order button from the supply ordering window. You can order
6 Order Supplies
replacement toner cartridge(s) from online.
Click the Help button from the upper-right corner of the window and click on any option you want to know
about.
4.1.6.2 Using the Smart Panel program (Macintosh and Linux only)
Smart Panel is a program that monitors and informs you of the machine’s status, and allows you to customize
the machine’s settings. For Macintosh, Smart Panel is installed automatically when you install the machine
software. For Linux, you can download Smart Panel from the Samsung website.
Smart Panel overview
GY
[
X
You can view the level of toner remaining in each toner cartridge. The
machine and the number of toner cartridge(s) shown in the above window
1 Toner Level
may differ depending on the machine in use. Some machines do not have
this feature.
2 Buy Now You can order replacement toner cartridge(s) from online.
3 User’s Guide You can view the online User’s Guide.
You can con gure various machine settings in the Printer Settings Utility
4 Printer Setting
window. Some machines do not have this feature.
4-19
4.1.7 Updating Firmware

This chapter includes instructions for updating the printer rmware. You can update the printer rmware by
using one of the following methods :
• Update the rmware by using the USB port.

• Update the rmware by using the network.
4.1.7.1 Update the firmware by using the USB port
[Upgrading preparations]
- usblist2.exe : Tool which sends rmware data to printer.

- Firmware le to upgrade
[Upgrade Procedure]
1. Turn the machine off.
2. Connect USB cable to printer.
3. Turn the machine on. Check if the printer is the ready status.
4. Drag the rmware le and Drop down on the usblist2.exe.

And then rmware update will be started automatically.
5. When upgrading is completed, machine is automatically re-booting.
4-20
4.1.7.2 Update the firmware by using the network
[Upgrading preparations]
- Wired or Wireless Network connection is established

- Firmware le to upgrade
[Upgrade Procedure]
1. Open Web-browser and input IP address of machine. Click “Login”.
2. Log-in Admin Mode

ID: admin, PW: sec00000
3. Select Maintenance menu and click “upgrade wizard”
4-21
4. Select rmware le using “browser” button and press next button.
5. SyncThru will check verify rmware le and compare version and press next button.
6. Machine starts upgrading. SyncThru will return home page after upgrading is completed.
4-22
4.1.8 Tech Mode
4.1.8.1 Entering the Tech Mode
In service (tech) mode, the technician can check the machine and perform various test to isolate the cause of
a malfunction. While in Tech mode, the machine still performs all normal operations.
To enter the Tech Mode
* SCX-5737FW (GUI model)
To enter the service mode, press 1,2,3 number keys simultaneously. When the password dialog box appears,
enter “1934” and press the “OK” button.
* SCX-483x/563x series (LCD model)
To enter the Tech Mode, press “ Menu + # + 1 + 9 + 3 + 4 ” in sequence
4-23
4.1.8.2 Tech Mode Menu
NOTE - Some menu items may not appear on the display depending on the options or models.
Depth 1 Depth 2 Depth 3 Depth 4

Data Setup Send Level -9~-15 -12
DTMF Level [Hi]=xx,[Lo]=xx
Pause Time 0~9
Dial Mode Tone,Pulse Tone
Modem Speed 33.6, 28.8, 14.4, 12.0, 9.6, 4.8 33.6
Error Rate 5%, 10% 10%
Clear All Mem.
Toner Low Level [1-30]% : 10
Clear Counts Enter Passcode Total Page CNT
[????] FLT Scan CNT
ADF Scan CNT
Engine Footer On
Off
HDD Format
Dial Tone On
Off
Machine Test Switch Test REDUCE_PANEL
COMPLETE_PANEL
Test Param Set
Modem Test
Dram Test
Rom Test
Pattern Test
Shading Test Shading&Print
Print
EDC Mode
Restart Machine
Report All Reports
Protocol
Supplies Info
Con guration
Error Info
Usage Counter
ComponentCheck
Service Support
4-24
4.1.8.3 Tech Mode Menu description
1) Data Setup
Send Level
You can set the level of the transmission signal. Typically, the Tx level should be under -12 dBm.
Caution : The Send Fax Level is set at the best condition in the shipment from factory. Never change
settingsarbitrarily.
DTMF Level
This is a setting value of the High level tone and low level tone at DTMF mode. (Not dial mode)
Pause Time
It shows the delay time when receving the pause input at auto dial.
Dial Mode
This function can choose dial method.
*Default : Dial(Dial/Pulse)
Modem Speed
You can set the maximum modem speed.Communication is done with modem speed automatically set at
lower speed when communicating with a slower speed modem since communication is done on the standard
of the side where modem speed is low for transmission/reception. It is best set 33.6Kbps as default setting.
Error Rate
When the error rate is about exceed the set value, the Baud rate automatically adjusts to 2400 bps. This
ensures that the error rate remains below the set value.You can select the rate between 5% and 10%.
Clear All Memory

The function resets the system to factory default settings.This function is used to reset the system to the
initial value when the product is functioning abnor-mally . All the values are returned to the default values,
and all the information, which was set by the user, will be erased.
NOTICE : Always perform a memory clear after replacing the main board. Otherwise, the system may not
operate properly.
Toner Low Level

The function is to set up the time to inform toner low status. This function can provide user convenience for
replacing the toner cartridge.
Clear Count
This function resets Total Page Count, Flatbed Scan Count, ADF Scan Count.
Engine Footer
This function is for monitoring of the engine status. If you perform this function, at printing, the setting value
for engine is shown on the bottom of the printed page.
4-25
2) Machine Test
Switch Test
Use this feature to test all keys on the operation control panel. The result is displayed on the LCD window
each time you press a key.
Test Param Set (Handset Model only)

You can set the parmeter for handset standard.
Caution : The parameter value is set at the best condition in the shipment from factory.
Modem Test
Use this feature to hear various transmission signals to the telephone line from the modem and tocheck the
modem. If no transmission signal sound is heard, it means the modem part of the mainboard malfunctioned.
Dram Test
Use this feature to test the machine’s DRAM. The result appears in the LCD display.If all memory is working
normally, the LCD shows << O K >>ROM TEST
Use this feature to test the machine’S ROM. The result and the software version appear in the LCD display.
• FLASH VER : 1.00 V
• ENGINE VER :1.00V
Pattern Test
Using this pattern printout, you can check if the printer mechanism is functioning properly.It is needed in the
production progress. Service person doesn’t need to use it.
Shading Test
The function is to get the optimum scan quality by the speci c character of the CIS (Contact Image Sensor).
If the copy image quality is poor, perform this function
to check the condition CIS unit.
EDC
There are 3 sub item in this menu.
They are NVM Read/Write, NVM initial, Test Routines. Use this function to check the status of the
components in the machine.
Restart Machine
You can reboot the machine by using a key without mechanic rebooting.
4-26
• EDC Mode Menu
NVRAM Read/Write
This menu can change a con guration value for engine rmware.
Code LCD Meaning Default Max/Min

103-0040 0040-Pick Int Delay Change time interval for paper pick-up 0 0~100(*100msec)
103-0050 0050-Pick Spl Delay Change time interval for paper pick-up 0 0~100(*100msec)
105-0030 0030-MHV DC K Charger HV Black DC Duty 720 50~900
106-0030 0030-Deve DC K Deve DC Black 431 50~900
107-0030 0030-THV K Transfer1 HV Black Duty 520 50~900
109-0000 0000-Ready Temp Target Temperature during standby mode. 10 0~15
109-0010 0010-Print Temp Target Temperature during run mode. 5 0~10
109-0030 0030-101-185mm Temp Offset temperature required on thermistor B for 5 0~15
paper width.
109-0040 0040-186-216mm Temp Offset temperature required on thermistor B for 5 0~15
paper width.
109-0050 0050-60gms Temp Media type offset for fuser roll temperature. 5 0~15
109-0060 0060-90gms Temp Media type offset for fuser roll temperature. 5 0~10
109-0070 0070-Bond Temp Media type offset for fuser roll temperature. 5 0~10
109-0080 0080-Trans Temp Media type offset for fuser roll temperature. 5 0~10
109-0090 0090-CardStock Temp Media type offset for fuser roll temperature. 5 0~10
109-0100 0100-Envelopes Temp Media type offset for fuser roll temperature. 5 0~10
109-0110 0110-Labels Temp Media type offset for fuser roll temperature. 5 0~10
110-0070 0070-LD Power K Black LD Power at Normal Speed 470 50~900
Test Routines
This menu can perform the operation test for the main components.
State Related
Code LCD Meaning
Displayed Components
100-0000 Main BLDC Motor Main BLDC Motor is On/Off On[Off] Engine
100-0010 Main BLDC Motor Detect if Main BLDC Motor runs at normal speed High[Low] Engine
Ready
100-0260 SMPS Fan Run Start/Stop Deve. Fan run On[Off] Engine
101-0000 Bypass Feed Clutch Engages drive to pick up a paper from bypass On[Off] Engine
Tray(MP Tray).
101-0010 T1 Pick-Up Clutch Engages drive to pick up a paper from tray1. On[Off] Engine
101-0020 T2 Pick-Up Clutch Engages drive to pick up a paper from tray2. On[Off] Engine
(Optional)
101-0050 Registration Clutch Engages drive to registartion rolls. On[Off] Engine
101-0190 Out-Bin Full Sensor Detect when a paper is at Duplex Ready sensor. High[Low] Engine
4-27
State Related
Code LCD Meaning
Displayed Components
102-0010 T1 Paper Empty Sensor Detect when paper is in Tray1. High[Low] Engine
102-0080 T2 Paper Empty Sensor Detect when paper is in tray2. High[Low] Engine
102-0280 Bypass Paper Empty Detects when paper is in Bypass Tray(MP Tray). High[Low] Engine
Sensor
102-0290 Feed Sensor Detect when a paper is at Feed sensor. High[Low] Engine
102-0300 T2 Feed Sensor (or Detect when a paper is at T2 Feed sensor. High[Low] Engine
Door Open) (optional)
102-0360 Regi. Sensor Detect when a paper is at Regi. sensor. High[Low] Engine
102-0370 Exit Sensor Detect when a paper is at Exit. sensor. High[Low] Engine
105-0030 Black MHV Bias Black MHV bias voltage on at normal drive level On[Off] Engine
106-0030 Black Dev Bias Black Dev bias voltage on at normal drive level On[Off] Engine
107-0030 Black THV Bias Black THV bias voltage on at normal drive level On[Off] Engine
107-0031 Black THV(-) Bias Black THV bias voltage on at normal drive level On[Off] Engine
107-0070 Black THV Bias Read Detect what the THV value is on the THV Roller Numeric 3 Engine
digits
109-0000 Fuser Temperature A Detects what the temperature A is on fuser. Numeric 3 Engine
digits
109-0040 Fuser Fan Run Fuser Fan Motor On/Off On[Off] Engine
109-0050 Fuser Bias Fuser bias voltage on at normal drive level On[Off] Engine
110-0000 LSU Motor1 Run Ready Detects if LSU motor1 runs at normal speed. High[Low] Engine
110-0060 LSU Motor1 Run LSU Motor1 On/Off On[Off] Engine
110-0110 LSU LD Power4 LSU LD4 Power On/Off (black) On[Off] Engine
4-28
3) Report
All Report
You can print all report at the same time.
Protocol
Protocol list shows the sequence of the CCITTgroup 3 T.30 protocol during the most recent sending or
receivingoperation. Use this list to check for send and receive errors.
Supplies info
Supplies Information Report shows toner cartridge information such as toner remaining, toner capacity, toner
product date etc.
Configuration
Con guration report shows the status of the user-selectable options. You may print this list to con rm your
changes after changing settings. This page provides useful information for service.
Error Info
Error Information Report shows error records.
Usage page
Usage page report shows usage page counts since service date. It shows total counts of the simplex print
and dupex print.
Component Check
Component Check Report shows the operation procedure of the machine test in tech mode.
Service Support
Customer Assistance Report shows the country setting procedure, F/W upgrade procedure, printing a Test
pattern page.
4-29
4.2 Troubleshooting
4.2.1 Procedure of Checking the Symptoms

Before attempting to repair the printer rst obtain a detailed description of the problem from the customer.
Power On
- No Power
OPE LED - Power Module error
ON?
- Main PBA
OPE LED Red LED on / See the troubleshooting

Green OK? Error message for error code
is displayed.
Print(test pattern)
printing
Quality is Refer to "Solution
Nomal? of Image Problem"
END
4-30
4.2.1.1 Basic Check List
1. Check the Power.
• Check that the power switch is turned on.

• Check that the power cable is plugged into the outlet and the printer.
• Check the voltage of the power outlet.
2. Check the LED of Panel.
• Is there OPE LED ON?

--> If not check power cable, switch SMPS or Main board.
• Is the abnormal Lamp?

--> Check the main PBA and cable harness.
3. Check the Paper Path
• Is there a Paper Jam?

--> Remove any paper fragments caught in the paper path.
• Paper Jam occurs repeatedly at a speci c point in the Paper Path

--> Open the fuser cover, Jam clear.
--> Dismantle the machine and carefully inspect the region where the jam occurs.
(Especially, check if paper fragments are caught in the Fuser
4. Print the Information Page (Configuration).
• Try printing a test page from a computer.

--> If there is an error check cables and driver installation.
5. Check the Print Quality.
• Is there are a Print Quality Problem?

--> Refer to the image quality problem.
6. Check consumables (toner etc.).
• Using the keys print the Test Pattern.

--> Expected life of various consumable parts, compare this with the gures printed and replace as
required
4-31
4.2.1.2 Initial Inspection
1. Check Power part
1. The printer does not work no matter how long you wait.
A. Is the Power Switch (printer and wall socket) turned on ?
B. Is the Power Cord connected to the printer correctly ?
C. Is the Power cord connected to the wall socket correctly ?
D. Is wall socket working ?
E. Is the unit rated at the same voltage as the supply ?
2. Does the Fan work when power is turned on?
A. Check the connectors on the SMPS.
B. Check the fuses in the SMPS.
2. Check the Installation Environment.
1. Ensure the installation surface is at, level and free from vibration.
If necessary move the printer.
2. Ensure that the temperature and humidity of the surroundings are within speci cation
3. Ensure that the printer is position away from any air conditioning or other heating or cooling equipment.
Also ensure that is not positioned in a direct draft from any air conditioning, fan or open window.
4. Ensure the printer is not positioned in direct sunlight.
If it is unavoidable use a curtain to shade the printer.
5. Ensure the printer is installed in a clean dust free environment.
Move the printer to clean area if necessary.
6. Some industrial or cleaning processes give of fumes which can affect the printer.
Move the printer away from this type of air pollution as it may leave chemical lm on optics.
3. Check paper type.
1. Use only paper which is of a suitable quality, weight and size?

See the user guide.
4. Check the overall condition of the printer
1. Is the printer properly maintained ?

Clean the Paper Transport Passages.
Any rollers with dirt surfaces should be cleaned or replaced.
4-32
4.2.2 Error Message and Troubleshooting

Messages appear on the control panel display to indicate the machine’s status or errors. Refer to the tables
below to understand the messages’ and their meaning, and correct the problem, if necessary.
NOTE - Some messages may not appear on the display depending on the options or models.
Troubleshooting
Error Code Error Message
Page
A1-1110 Error #A1-1110: Turn off then on. 4-35 page
C1-1110 Prepare new cartridge
4-36 page
C1-1120 Replace new cartridge
C1-1410
Install toner cartridge. 4-36 page
C1-1411
C1-1512 Not Compatible Toner cartridge. 4-37 page
H1-1210 Paper jam in Tray2. 4-37 page
H1-1222 Pulled Out Tray2 Cassette. 4-37 page
H1-1252 Paper is empty in Tray2. 4-38 page
M1-1010
Paper Jam in Tray1. 4-38 page
M1-1110
M1-1210 Paper Jam in Tray2. 4-38 page
M1-1610 Paper Jam in MP tray. 4-39 page
M1-2210 Tray2 Door Open. Close it. 4-39 page
M1-3221 Not installed Tray2 4-39 page
M1-5112 Paper is empty in tray 1. 4-40 page
M1-5212 Paper is empty in tray 2. 4-38 page
M1-5612 Paper Empty in MP Tray. 4-41 page
M2-1110 Paper Jam inside machine. 4-42 page
M2-2310 Paper Jam bottom of duplex. 4-43 page
M3-1110 Paper Jam in exit area. 4-43 page
M3-2130 Output bin full. Remove paper. 4-44 page
S1-2411 Error #S1-2411 Turn off then on. 4-45 page
S2-4110 Door open. Close it. 4-45 page
S3-3121 Scanner Locked. 4-46 page
S4-2111
Memory Full. Remove Job. 4-46 page
S4-2112
S6-3123 Network Problem: IP Con ict. 4-46 page
S6-3128 802.1x Network Error. 4-47 page
U1-2320 Error #U1-2320 Turn off then on. 4-47 page
U1-2330 Error #U1-2330 Turn off then on. 4-48 page
4-33
Troubleshooting
Error Code Error Message
Page
U1-2340 Error #U1-2340 Turn off then on.
4-48 page
4-49 page
U3-3113
Document jam. Remove jam 4-50 page
U3-3114
U3-3213
U3-3313 Document jam. Remove jam 4-50 page
U3-3314
U3-4110 Door of scanner is open. 4-50 page
4-34
● Code ● Error message

A1-1110 Error #A1-1110: Turn off then on.
● Symptom / Cause
After working the main BLDC motor, the Ready signal has not occurred within 1 sec.
1. Harness is defective. Connector is not connected properly.

2. OPC coupler in the toner cartridge has overloaded.
3. Main BLDC motor is defective.
4. Engine board is defective.
● Troubleshooting method :
※First, turn the machine off then on. If the error persists, refer to the following.
1. Check if the motor connector is connected properly. Reconnect it.
2. OPC coupler has overloaded.

After removing the toner cartridge, rotate the OPC coupler. (Spec : 6 kgf.cm)
If there is any damage, the OPC coupler can’t rotate well.
Replace the toner cartridge.
3. The main BLDC motor is defective.

- Unplug the connector from the motor carefully.
- Replace the main BLDC motor with new one.
4. If the problem persists, replace the main board.
4-35

C1-1110 / C1-1120 Prepare new cartridge / Replace new cartridge
● Symptom / Cause
The remaining toner cartridge is less than 10%
The toner cartridge is at the end of its life.
● Troubleshooting method
1. Print the supply information report. (Menu > System Setupr > Report > Supplies Info.)
Check the life remaining of the toner cartridge.
If its life is at the end, turn the machine off and replace the toner cartridge with new one.

C1-1410 Install toner cartridge.
C1-1411
● Symptom / Cause
The toner cartridge is not installed.
1. Turn the machine off then on.
2. Remove the toner cartridge.

Thoroughly roll the cartridge ve or six times to distribute the toner evenly inside the cartridge.
And reinstall the toner cartridge.
4-36

C1-1512 Not Compatible Toner cartridge.
● Symptom / Cause
Toner cartridge is not compatible.
1. Print the supply information report. Check information of the toner cartridge.
2. If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.

H1-1210 Paper jam in Tray2.
● Symptom / Cause
A paper jam was detected in the feed area of the tray2.
1. Paper was inserted abnormally or was not loaded in the cassette properly.
2. Pick Up unit has a problem.
1. Open the Tray2 and remove the jammed paper.
2. If there is any defective part in the pick up unit, replace it.

H1-1222 Pulled Out Tray2 Cassette
● Symptom / Cause
The option tray is not inserted perfectly.
1. Remove and re-install the option tray.
4-37

H1-1252 Paper is empty in Tray2.
M1-5212
● Symptom / Cause
Paper is empty in Tray2. The status LED is red.
1. There is no paper in the tray2.

2. Actuator-Paper Empty is defective.
3. Photo Sensor is defective or connection is bad.
4. Main Board is defective.
1. Load the paper in the tray2.
2. If the Actuator-Paper Empty is defective, replace it.
3. If the Photo Sensor is defective, replace it. Check if the connector is connected properly.
4. If the problem persists, replace the Main Board.

M1-1010 Paper Jam in Tray1.
● Symptom / Cause
The jammed paper has occurred in the tray1,2
1. Pick-Up or Torque Limiter Roller is contaminated or worn out.

2. There is some obstacles in the paper path.
1. Clear the jammed paper (refer to 4.1.3.2). If the problem persists, check the following.
2. While pushing the Paper Empty Sensor, send the printing data.
Check if the pick up roller is rotating normally.
3. Check if there is any obstacles in the paper path (from Pick-Up to Feed Sensor).
The feed roller should be especially checked.
4. Print out the Supplies Information. Check the Tray 1,2 Roller Life and Tray1,2 Torque Limiter Life.
If the life came to the end, replace the relative roller.
4-38

M1-1610 Paper Jam in MP tray.
● Symptom / Cause
The jammed paper has occurred in the MP tray.
1. MP Pick-Up or MP Torque Limiter Roller is contaminated or worn out.

1. Clear the jammed paper. If the problem persists, check the following.
2. While pushing the Paper Empty Sensor, send the printing data.
Check if the pick up roller is rotating normally.
3. Check if there is any obstacles in the paper path (from Pick-Up to Feed Sensor).
The feed roller should be especially checked.
4. Print out the Supplies Information. Check the MP Tray Roller Life and MP Tray Torque Limiter Life.
If the life came to the end, replace the relative roller or MP Unit.

M1-2210 Tray2 Door Open. Close it.
M1-3221 Not installed tray2.
● Symptom / Cause
The option tray is not inserted perfectly.
Remove and re-install the option tray.
4-39

M1-5112 Paper is empty in tray 1.
● Symptom / Cause
Paper is empty in Tray1. The status LED is red.
1. There is no paper in the tray1.

1. Load the paper in the tray1.
Empty
actuator
Empty sensor
4-40

M1-5612 Paper Empty in MP Tray.
● Symptom / Cause
Paper is empty in MP Tray. The status LED is red.
1. There is no paper in the MP tray.

1. Load the paper in the MP tray.
Empty
actuator
Empty sensor
4-41

M2-1110 Paper Jam inside machine.
● Symptom / Cause
A paper jam was detected at the feed sensor.
1. The feed sensor is defective.

2. The Regi Roller was contaminated or worn out.
4. The driving for the toner cartridge has some problem.
5. The driving for the fuser unit has some problem.
1. Remove the jammed paper. If the error persists, check the followings.
2. Check if the feed sensor connector is connected properly.
Regi. sensor
Feed sensor
3. Check if the Regi roller is contaminated or worn out. If yes, replace it.
4. Check if there is any obstacles or contamination in the paper path. If yes, clean or remove it.
4-42

M2-2310 Paper Jam bottom of duplex.
● Symptom / Cause
A paper jam was detected in the bottom of duplex.

2. The paper guide in the tray was not adjusted properly.
3. The exit sensor was not assembled properly.
1. Remove the jammed paper.
2. Remove the contamination or obstacles in the paper path.
3. Adjust the paper guide properly.
4. Check if the exit sensor is assembled properly. Reassemble it.

M3-1110 Paper Jam in exit area.
● Symptom / Cause
A paper jam was detected in the exit area.
2. Check if there is any obstacles or contamination in the paper path. If yes, clean or remove it.
4-43

M3-2130 Output bin full. Remove paper.
● Symptom / Cause
The machine detected that the output tray has got full or the bin-full sensor is defective.
1. Output tray is full.

2. Outbin full sensor connection is wrong.
1. Remove the paper on the output tray.

(The maximum loading capacity is 150 sheets based on standard paper(80g/m2).)
2. Check if the Bin-full Sensor connector is connected properly.

Reconnect it or replace the Bin-full sensor.
4-44

S1-2411 Error #S1-2411 Turn off then on.
● Symptom / Cause
A communication error failure has occurred at HDD of main controller.
1. Format the hard disk.

2. If the problem persists, replace the hard disk.

S2-4110 Door open. Close it.
● Symptom / Cause
Door is open or the cover open switch is defective.
The status LED is red.
1. Check if the front door is closed perfectly.
2. Check if the rear door is closed perfectly.
3. Check if the connection between the main board and HVPS board is correct.
4. Check if the cover open switch on HVPS board is operated properly.

If it is defective, replace the HVPS board.
Cover Open Switch
4-45

S3-3121 Scanner Locked.
● Symptom / Cause
Scanner lock error has occurred. CIS does not move.
1. Check if the CIS unit is moving when power on.

2. Check if the at cable is connected to the CIS unit properly. Re-connect or replace the cable.
3. If the CIS is defective, replace it.
4. Check if there is any defective part in the scanner unit. (Gear, Belt, Motor etc.)
5. If the problem persists, replace the main board.

S4-2111 Memory Full. Remove Job.
S4-2112
● Symptom / Cause
The fax memory is almost full.
Print or remove the received fax job in Secure Recieve.

S6-3123 Network Problem: IP Con ict.
● Symptom / Cause
Network has some problem.
- IP address con icts with that of other system.
- Communication error
- There is no response when checking the ping test.
Change the machine’s IP address.

- Set-up the IP address in this order, Network -> TCP/IP (IPv4) -> STATIC.
- In case of DHCP or Bootp, reboot the machine to receive a new IP address.
4-46

S6-3128 802.1x Network Error.
● Symptom / Cause
802.1x Network Error
- The con rmation was requested for wired port, the server has rejected.
- The con rmation protocol is not the same or user information (ID/Password) is wrong.
Check the setting-up for 802.1x con rmation server.

- Re-enter the server information and con rmation protocol.
- Re-enter the user information.

● Symptom / Cause
The temperature control of fuser unit is abnormal. (Open Heat Error)
1. Turn the machine off. Re-install the fuser unit.

Then turn the machine on. Is the error message is disappeared?
2. If the problem persists, turn the machine off and remove the fuser unit.
Check if the fuser connector is connected properly.
Check if the input voltage is normal.
4-47

● Symptom / Cause
The temperature control of fuser unit is abnormal. (Low Heat Error)

a. Check if the fuser connector is connected properly.
b. Check if the input voltage is normal.
c. Check if the thermistor is twisted or contaminated.

● Symptom / Cause
The temperature control of fuser unit is abnormal. (Over Heat Error)

a. Check if the fuser connector is connected properly.
b. Check if the input voltage is normal.
c. Check if the thermistor is twisted or contaminated.
4-48

U2-1111 / U2-1113 Error #U2-1111 Turn off then on. / Error #U2-1113 Turn off then on.
● Symptom / Cause
LSU Motor does not work normally.
1. Harness connection error.

2. LSU is defective.
3. Main board is defective.
1. Execute the LSU motor test in EDC mode. Check LSU motor operation sound.
2. If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly.
(picture-①)
3. If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly. (picture- ②,③)
4. Check if the LSU harness is defective. (picture-④)
5. Reconnect the LSU harness and then execute the LSU motor test again.
6. If the problem persists, replace the LSU.
7. If the problem persists after replacing LSU, replace the main board.
4-49

U3-3113 Document jam. Remove jam.
U3-3114
U3-3213
U3-3313
U3-3314
● Symptom / Cause
A document jam was detected in ADF/DADF unit.
2. If the problem persists, turn the machine off then on.
3. Open the ADF/DADF COVER-OPEN. Check if the roller in pick up unit is worn out or contaminated.
Replace the pick up unit.
4. If the document jam occurs continually, check the following.

a. Check if the ADF/DADF drive unit is working normally.
b. Check if the connection between ADF/DADF and scanner is OK.

U3-4110 Door of scanner is open.
● Symptom / Cause
Scanner door is not closed correctly.
Close the scanner door.
4-50
4.2.3 Image Quality problem
1) Vertical Black Line and Band
Description : 1. Straight thin black vertical line occurs in the printing.

2. Dark black vertical band occur in the printing.
1. Damaged develop
roller in the Toner cartridge.
If causes 1 and 2 occur in the
Deformed Doctor-blade or cleaning-blade.
toner cartridge, replace the toner
2. Scratched surface of cartridge and try to print out.
the charge roller in the
toner cartridge.
3. Partly depression or Replace the transfer roller if

deformation on the surface of occurred as No. 3.
the transfer roller.
4-51
2) Vertical White Line
Description : White vertical voids in the image.
Foreign matter stuck onto the

1. Foreign matter stuck onto the window : Clean the LSU window
window of internal lenses with recommended cleaner(IPA)
of LSU mirror. Clean the window with a clean
cotton swab.
2. Foreign matter or
toner particles between the toner
cartridge roller and blade. (In case the life of the Replace the toner cartridge.
toner cartridge has been expired, white
lines or light image occur in
front of the image.)
3. It may occur when Burr and No 3. : Remove the foreign matter

foreign substances are on the window and burr of the exposure window.
of the toner cartridge frame. (toner cartridge)
No. 4. : Open the front cover and

4. If the fuser is defective,
check ribs that corresponds to the
voids occur periodically at the
position of the voids. Remove if
top of a black image.
found.
5. It may occur when foreign If the problems are not solved,

substances are on the OPC Drum. replace the toner cartridge.
4-52
3) Horizontal Black Band
Description : Dark or blurry horizontal stripes occur in the printing periodically.

(They may not occur periodically.)
Clean each voltage terminal of the

1. Bad contacts of the voltage Charge, Supply, Develop and
terminals to developer. Transfer roller.(remove the toner
particles and paper particles)
2. The rollers of
developer may be stained. 1. Clean the right Gear that has
relatively small gap of the teeth
Charge roller = 26.7 mm
in the OPC.
Developer roller = 36.78 mm
2. If the malfunction persists,
OPC drum = 75.49 mm
replace the developer.
Supply roller = 69.57 mm
4-53
4) Black/White Spot
Description : 1. Dark or blurry spots occur periodically in the printing

2. White spots occur periodically in the printing
1. If dark or blurry
black spots occur periodically,
the rollers in the toner cartridge may be conta- Print several OPC cleaning Mode
minated with foreign matte or paper particles. Prints and then run the Self-test
(Charge roller : 26.7mm interval 2 or 3 times.
OPC drum : 75.49mm interval)
2. If faded areas or voids In case of 75.49 mm interval

occur in a black image at intervals unremovable in 1, cleanly remove
of 75.49 mm, or black spots occur elsewhere, foreign substances stuck on the OPC
the OPC drum surface is location equivalent to black spots and
damaged. white spots with a dry duster.
1. The transfer roller guarantees

50.000 sheets printing. If the
3. If a black image is roller's life is expired, replace it.
partially broken, the transfer voltage is 2. In case of 26.7 mm interval
abnormal or the transfer roller's unremovable in 1, take measures
life has expired. as to replace the develop-er
cartridge and try to print out.
5. Clean the inside of the set against
the paper particles and foreign
matter in order not to cause the
trouble.
4-54
5) Light Image
Description : The printed image is light, with no ghost.
1. Develop roller is stained when

Check if the Toner Save mode is off.
the toner of toner cartridge is almost
consumed.
2. Ambient temperature is below than 10୅. Replace the developer cartridge

and try to print out.
3. Bad contact caused

by the toner stains between the high Wait 30 minutes after printer is
voltage terminal in the HVPS and powered on before you start printing.
the one in the set.
1. Clean up the contaminated area

by the toner.
4. Abnormal output from the HVPS. 2. Replace the HVPS if the
problems are not solved by the
above four directions.
4-55
6) Dark Image or a Black Page
Description : The printed image is dark.
NO Dark selected
via RCP?
YES
Change to
Normal and test
NO
Same at Normal? END
YES
Works correctly NO Repair or replace the defective

with -450V of Bias component
voltage?
YES
Works Toner over supply due to the

NO adjustment fault of metering
correctly after
replaced LSU? blade in toner cartridge
-> Replace toner cartridge
YES
The power of LSU is set

high or internal problem
-> Replace LSU or adjust
volume
4-56
7) Uneven Density
Description : Print Density is uneven between left and right.
1. The pressure force

on the left and right springs of the
transfer roller is not even, the springs are Replace both the left and right
damaged, the transfer roller is improperly Spring Holder.
installed, or the transfer roller
bushing or holder is
damaged.
2. The toner level is not

even on the developer roller due to Replace the toner cartridge.
the bad blade.
4-57
8) Background
Description : Light dark background appears in whole area of the printing.
1. Does character exist less than The toner cartridge is basically

2% per a page, and hasn’t it been designed to print 2,000 sheets
used long time? with 5% image.
2. Does recycle paper be used? The A/S is not guaranteed if using

recycle paper.
3. Has the life span of the Replace the toner cartridge when
Toner cartridge ended? the life span of it has been ended.
4. Is the movement(Up and Down) Clean the bushing part of the

of the transfer roller smooth? transfer roller.
5. Is the HVPS normal? If the problem is still not solved,

replace the toner cartridge.
4-58
9) Ghost
Description : Ghost occurs at 94.4 mm intervals of the OPC drum in the whole printing.
1. Bad contacts
94.4mm
caused by contamination from

toner particles between high voltage Clean the terminals when
terminal in the main body and the contaminated by toner particles.
electrode of the
Developer.
2. Bad contacts
caused by contamination
from toner particles between high Occur in the toner cartridge,
voltage terminal in the main body and the replace the developer and try to
one in the HVPS board. print out.
3. The life of developer is expired. Replace the Main board if not

solved by the above directions 1-2.
4. Transfer roller lifetime If not solved by the direction 3,

(50.000 sheets) has expired. check the transfer roller lifetime
and replace it.
5. Abnormal low temperature Wait about 1 hour after power on

(below 10୅). before using printer.
4-59
10) Stains on the Face of Page
Description : The background on the face of the printed page is stained.
1. Toner leakage due to

improperly sealed developer
. Replace the toner cartridge
2. If the transfer roller is If the transfer roller is contaminated,

contaminated, stains on the face of print the 2~3 blank pages.
page will occur.
4-60
11) Stains on Back of Page
Description : The back of the page is stained at 47 mm intervals.
1. Transfer roller is contaminated. Replace the transfer roller.
Disassemble the fuser and clean

the H/R(Heat Roller) and P/R
2. Pressure roller is contaminated.
(Pressure roller). And check the
area between H/R and Thermistor.
If contaminated, clean the area not
to be deformed.
4-61
12) Blank Page Print out
Description : Blank page is printed.
NO A on
No image? next page
YES
Self test NO Self testing NO Retest after replacing the

pattern prints? is possible ? connector or controller board
YES YES
Check connection to Take out the cartridge

computer or replace and prepare the tester
controller for electronic connection
Is the OPC
terminal of machine NO Repair or replace the GND
is well-connected terminal
to Frame?
YES
Does the Check the path between

video data line to NO Main board
LSU transit to High/Low and HVPS. Repair or replace
when printing? the defective component
or board
YES
The mirror in LSU might be

misplaced so the light path to the
OPC deviates ->Repair or replace
LSU or remove any defective
matters in the machine
4-62
4.2.4 Other errors
1) Multi-Feeding
Description : Multiple sheets of paper are fed at once.
1. Clutch malfunction
(the solenoid does not work properly) Replace the solenoid if necessary.
2. Pick up/Retard/Forward
Clean the contaminated roller with
roller are contaminated with
soft cloth with Isopropyl Alcohol.
foreign matter.
4-63
2) No Power
Description : When system power is turned on, all lamps on the operator panel do not come on.
1. Check if the power input and Replace the power supply cord or
SMPS output are normal. SMPS.
2. Check if the OPE connector is 1. Reconnect the OPE harness.

connected properly. OPE harness or 2. Replace the OPE harness or
OPE board is defective. OPE board.
4-64
4.2.5 Network problems and solutions
Before Troubleshooting, check below check point.
Check Point Action

A. Connected or Not connected
LAN cable check B. Wrong cable (defected cable, crossover cable)
C. Connection connector (Link partner check)
A. Link LED check (Link LED On when connected)
Network LED check
B. Activity LED check (No packet Regularly blinking, packet random blinking
depend on Printer Model)
A. Printed correctly. If not, NIC is in lock up state or NIC can not communicate
with printer
B. Network address value check : IP address, Subnet Mask, Gateway, MAC
address
C. NIC F/W version (Correct or not)
Print Network test page
1) V1.0x.xx : NPC3
2)V2.0x.xx : NPC3H
3)V3.0x.xx : PHY Board
4)V4.0x.xx : On Board
D. Protocol Enable / Disable
E. WLAN module / Status check if WLAN available.
A. Toner Empty, Paper Empty and so on : Hard Stop cases (Job can be
Printer SET status check
nished completely)
Network Printer Configuration check
1. Address Con ict check

A. IP address Con ict : Same IP address in a network
• Unplug network cable and PING test
B. MAC address Con ict : Same MAC address in a physical network
• Default MAC address or same MAC address (PING and ARP –a)
2. IP get method check (Panel or SWS)

A.DHCP/BOOTP : IP can be changed after rebooting
B. Auto IP address
3. Protocol Enable / Disable, Port Number (In SWS)
4. IP ltering On/Off
5. SNMP community name check (When SNMP no response)
4-65
Host PC Configuration check
1. Address Con ict check

A. IP address Con ict : Same IP address in a network
• Unplug network cable and PING test at other PC
2. Protocol Enable / Disable, Port Number in printer driver
Factory Default
1. Network Value changed to default value

A. Some of Network value will not be changed immediately.
B. Factory default operation will be done after Power Off / Power On
4-66
Rainier 31
Service Manual
Block Diagram
2010 .007 .12
Fuser
LD power Ambient THV read
thermistor
RTC Serial Flash (8M) Flash (16M)

MAINBOARD
battery for FAX for OS
Modem
Speaker
DAC RTC ADC SPI Flash Conexant
Power S/W
5. System Diagram
OPE 2line Home

UART x 4 Buzzer , Power S/W Sensor
EEPROM(64K) Debug
CPU: Chorus 3 I2C x 2
1 BLDC Motor
Clock : 360Mhz SCF
(Rst,Rx,Tx,REQ)
PHY IC 10/ 100 540?
PWM x 12 MAC
AC201A1KMLG LAN
5-1
5.1 Block Diagram (SCX-483xFD)
DDR2 LSU SCAN NCRUM

GPIO USB 2.0
controller controller IF / AFE
5. System Diagram
Engine (TBD)
DCDC 3.3V
- Solenoid ? ST1S10 system
(MP,Pickup ,Regi)
DDR2 128 M ISP1582 STEP
- Sensor ? ONBOARD + 5V DCDC 1.8V 0.9V A3983
ST1S10 DDR
UR5596 VTT
(Exit, Feed, Empty , S MP S
256 MB
Regi,Out bin full , MP,
ADF_DET, ADF_POS, 1 DIMM DCDC 1.0V
ADF_COVER, Duplex) ST1S10 CHORUS 3 LAFE1001
H/ W
STEP
- Fan (Main, USB Device USB HOST
SMPS,MIDDLE) PROTECT A3983
HVPS Board LSU

(MHV,THV,DEV_DC SMPS(TYPE2) ADF Unit CIS Scan Unit
,FUSER_BIAS) 24V, 5V, FDB, Relay 2BEAM
Cover S/ W
Samsung Electronics
Rainier
Service Manual
SCX-4833FR,SCX-5637FR,SCX-5737FW
skG m Block Diagram V0.3
h {o}G
2010.09.30
o}wzGi
Oto}S{o}Skl}kj
Sm|zlyiphzP
jGzV~ kkyYGY\]tG
vuivhykG y{jG mOZYtP thpuivhyk
swljX Gvz
R
l \XYtiGkpttG
TzGf tG
Otw SwSyP z
kkyYG y{j j
m zwp

l oGz
Power S/W vwlMsjkGky}
TzGf i¡¡GSGwGzV~
OlSGmSGl SG w~tGG [ [ssjk
ySvGGSGtwSG
|hy{GG[
hkmkl{SGhkmwvzSG [UZIG{m{Tsjk
hkmjv}lySGkP CPU: Chorus [ llwyvt
nwpv OZYriGG ][riP
Tm Clock: ]WWMhz pYjGGY k r Gw
OtS ztwz SGtpkkslP i¡¡SwGzV~
5-2
sz|G PHY IC n
thj zjmG\[Wf
sz| Yilht RTL8211D shu OySyS{SylxP
zjhu z{lw
t |ziGYUWG pmGVGhml LAFE1001
5. System Diagram
XGiskj hZ`_Z ujy|t
DCDC 3.3V
ST1S10 system
oV~
wyv{lj{ |ziGo|i |ziGo|i
DCDC 1.1V
24VS1 5V jpzGzG|
ST1S10 CHORUS 4 ns_\Wn ns_\Wn
zGt OXP
Block Diagram (SCF-483xFR/563x/573x series)
1.8V
DDR2
DCDC
5V ISL88550 hkmG|
24V2 24V1 SMPS A 0.9V ztSzO[P
VTT
SjOZP
|zi |ziGovz{OZP |ziGovz{OYP zjT[_ZZmy

ztwzO{wlYP ztwzO{wlZP k T mkp T ~shu
Y[}SG\}ztwzS T [nG|ziGmG T [UZIG{m{Tsjk zjT\]Z^my
Y[}XSY[}YSG\}ztwzS
mkiSGy mkiSGy T kGw
zjT\^Z^m~
Samsung Electronics
zG
o
Service Manual
ADF zwlhrly z
ADF_JOINT
S CX-4932FN
ONLY
i|ly
OPE _LCD
LCD (2-Line)
1 OUT2B
t{ 2 OUT2A CIS
3 OUT1B
z{lw 4 OUT1A
1
2
1
2
1
2
3
5 GND
mnuk 6 GND
CN(1.5mm) MODEM LSU
A DF_IF z
7 3.3VPS (Conexant ) (Dual Beam )
A DF _IF
hkmwwvz zlu 8 GND t
5V
9 nADF_P _POS
CN(1.5mm)
OPE
N. C
N. C
nRD
GND
GND
GND
nWR
3. 3V
3. 3V
GND
GND
GND
GND
GND
24V S
hkmjv}lyvwlu
nS H_1
nS H_2
nHsy nc
10 nADF_COVER_SENS
nRING0
DAT A7~
~DA TA0
nLD_O N
A DDR1~
~A DDR7
3. 3V _LS U
V DO_1_P
V DO _1_N
V DO_2_P
V DO _2_N
11 GND
K EY CLI CK
5V
S CANNER_HOM E
GND
hkmwwvz zlu
nM _RE S ET
HOOK _DET
LD_P OWE R
12 nADF_P _DET t{
nCS _MO DE M
nREA DY _LS U
nI NT_MO DE M
z{lw
1
2
1
2
3
4
5
6
7
8
9
3~
11
19
20
21
22
23
24
25
26
27
28
29
30
10
11
12
13
14
15
16
17 CLK_LS U_MOT
18
19 nLSU_M OT_E N
20
21
22
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
10
10
11
12
~10
12~
~18
O UT 2B
O UT 2A
O UT 1B
O UT 1A
G ND
G ND
3. 3VP S
G ND
nA DF_P _POS
nA DF_COV ER_SE NS
G ND
nA DF_P _DE T
9
8
7
6
5
4
3
2
1
12
11
10
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
3
4
5
6
7
8
9
2
10
11
12
13
14
15
16
17
18
19
20
10
10
11
12
10
11
12
5V
N. C
12V
N. C 24
N. C 27
nRD 22
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND 1
GND 11
GND 19
nW R 23
3. 3V 28
3. 3V 29
GND 30
24V S
nS H_1
nS H_2
nHs ync
OUT2B
OUT2A
OUT1B
OUT1A
OUT1A
OUT1B
OUT2A
OUT2B
3. 3VP S
CI S_S P
nLD_O N
DAT A7~ 3~
~DA TA0 ~10
thpu
A DDR1~ 12~
~A DDR7 ~18
AF E_S IG
3. 3V _CI S
PULL-UP
3. 3V _LS U
V DO_1_P
V DO _1_N
V DO_2_P
V DO _2_N
3CIS _CLK
CI S_B LE D
CIS _GLE D
CI S_RLE D
ZUZ}ztwz ZUZ}jv
HOOK _DET 20
LD_P OWE R
nADF_P _DET
nCS _MO DE M 21
nREA DY _LS U
nADF _P_P OS
nI NT_MO DE M 26
nRS T_MO DE M 25
CLK_LS U_MOT
nLSU_M OT_E N
SCA N_CONTROL1
CN4(2mm ) CN9(FFC 1mm) CN21(FFC 1mm)
GND
SCA NNE R_HOME
nRS T_P ANE L
nPOWE R_SW
GND
GND
PA NEL_TX D
PA NEL_RX D
MOD_B UZ ZE R_CON
KE YCLI CK _CON
mGj
nA DF_COVE R_SE NS
SCAN_MTR CN26(FFC 1mm) MODE M_IF LS U_IF
tG CIS _IF
CN3(1.5mm) CN5(1.5mm )
z OP E I/F
A DF_IF 24V 1
24V 2
24V 3
3.3V 4
24V S 12 1 24V S
Y[}z 3.3V 5
GND 11 2 GND
THV_RE A D 10 3 THV _RE A D
ͶͶ΁΃΀; 3.3V 6
nTHV_E N 9 ZUZ}z ͵͵΃ͣ͑ nRS T_S CF 7
4 nTHV _E N ;ͣͥͦͣ͢
P WM_THV 8 5 P WM _THV S CF_TX D 8
P WM_DE V_DC 7 6 P WM _DE V_DC ΄͵΃Ͳ; S CF_RX D 9
o}wz P WM_MHV 6 7 P WM _MHV
͙͑ͧͥͼ͚ N. C 10
HVP S
SCF_IF
Supply P WM_FUS E R_B IA S 5 8 P WM _FUS E R_B IA S ͙ͣͩ͢;ͳ͚ nS CF_OP T 11

GND 4 9 GND N. C 12
CN8(1.5mm)
CN16(2mm)
GND 3 10 GND N. C 13
DEV 3.3V S 2 11 3. 3V S GND 14
3.3V _Cov er_Open 1 12 3. 3V_Cover_Open GND 15
THV ZUZ}jvX
GND 16
΄Ͷ΃ͺͲͽ͑͑ͷͽͲ΄͹ GND 17
OPC MHV GND 18
͙ͩ;ͳ͚
Ϳ΀΃͑ͷͽͲ΄͹
1 GND 1
5-3
͙ͧ͢;ͳ͚ GND
2 GND 2
NC
(2m m)
Varistor 3 24V S 3
CN12
}jsr
M AI N FA N
RD-
4
3.3V
5
RD+
S CHORUS3 6
25MHz TD-
M mhu 3.3V
7
D 8
C |ziGGjsr 3.3V pullup
thpu 9
FUSER 1 GND LE D1
2 CLK 10
BIAS R 3.3V
DIO 11
DRUM 3 LE D2
CRUM
(2mm )
CN7 NETWORK_IF
Clock 12
CN23
U 4 3.3V _CRUM GND
Generator ͿΖΥΨΠΣΜ GND
13
5. System Diagram
14
M ASM3P2863 A thpuGjsr ͢͢͡͠͡͡
mhu 1 24V S V B US 1
T 2 GND DM 2
(2m m)
kl}lsvwlyG|
CN11
DP 3
SM PS F AN
ztwz
5.2 Connection Diagram (SCX-483xFD)
CN28
USB_IF
ͺ΄΁ͦͩͣ͢ GND 4
12MHz
USB 2.0
mhu 1 24V S GND 1
2 GND 5V 2 USB TO
(1.5m m)
CN30
CN20
S MP S FA N
t NC 3
P OWER
PARALLEL
PA RALLE L
GND 1
CN15
24V OFF 2 5 GND CN(2 mm) CN6(1. 5mm) (1 .5mm )
ztwz Y[}z CN14(2mm) CN(2mm ) CN(2mm) CN24(1. 5mm ) CN19
Relay 3 4 24V OFF P_EXIT OUTBIN AIR
CN10( 2mm)
SM PS
MP SENSOR SENSOR SENSOR E ras er&Duplex TEMP
CN4
MAIN MOTOR USB_IF
Fuser ON
S MP S
5 24V S
CN18
2
(2mm)
1 Fuser ON
m|zlyGvu
GND 2 2 GND
THE RM_1
24VS
MP _CLT
3.3V S
GND
MP _SE NS
3.3V
GND
P EA PE R_EX IT
3.3V PS
GND
nSENS_BIN_ FU LL
3.3V_C_OPEN1
3.3V_C_OPEN2
3.3V S
GND
P _E mpt y
S ENS
3.3V S
GND
REG I_S ENS
3.3V S
GND
FE ED_S ENS
5V
E RA SE R_LED
nSENS_DUPLEX
GND
A MB IE NT
GND
MO T_DIR
PW M_MO T
MO T_REA DY
MO T_EN
GND
MO T_BRE AK
GND
GND
24VS
24VS
24VS
Pi ckup_CLT
24VS
Regi_CLT
VB US
DM
DP
GND
24V 3 3 24V
SM PS
SM PS
CN3
CN17
GND 4 GND
1
2
1
2
3
4
5
1
2
3
1
2
3
4
5
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
1
2
3
4
5
6
7
8
9
1
2
3
4
10
11
12
13
14
Y[}
\}ztwz
INLET FUSER
zvs zvs
{X js h
9
8
7
6
5
4
3
2
1
10
{
lyhzly k z
y tw tw l wG j
w ltw{ ylnp mllk slk
j z z v v
j j z z z
z k
m|zlyG| t{ |zi
{z
iskj
t Rainier Hardware Team

pusl{ t R&D Group 2
Samsung Electronics
100409
Samsung Electronics
Service Manual
Scanner
CLX-4833FR/5637FR Home
DADF SPEAKER Sensor
1 LE D_A NODE N. C 1 12 N. C
DADF Paper Detect
2 GND GND 2 11 GND
Sensor 3 nSENS_DADF_ P_DET GND 3 10 GND BUZZER
4 LE D_A NODE DA DF_RE GI_S OL 4 9 DA DF_RE GI_S OL
DADF Cover Open 5 GND DA DF_MODULE _DE T 5 8 N. C
OPE _LCD
SE NSOR
6 nSENS_DADF_ COVER_OPEN
CN(1.5m m)
Sensor nS E NS_DA DF_P _DE T 6 7 nS E NS_DA DF_P _DE T LCD (4-Line)
7 N.C
nS E NS_DA DF_P _RE GI 7 6 nS E NS_DA DF_P _RE GI
1 DA DF_MOT _S LE E P 8 5 DA DF_MOT _S LE E P
ADF_JOINT
DADF Paper Pos LE D_A NODE
CN(1. 5mm )
2 nE N_DA DF_MOT 9 4 nDA DF_MOT _E N KEY PANEL (CLX -5737FW)
CN(1.5mm)
GND
Sensor 3 nSENS_DADF_ P_POS DA DF_MOT _P LS 10 3 DA DF_MOT _P LS
4 LE D_A NODE DA DF_MOT _CURRE NT 11 2 DA DF_MOT _CURRE NT 3CH CIS
1
2
DADF Paper Regi GND
SE NSO R
5 DA DF_MOT _DIR 12 1 DA DF_MOT _DIR CN(1.5mm)
CN(1.5m m)
1
2
1
2
3
6 nSENS_DADF_ P_REGI
Sensor 1
LSU CLX -5737FW
GND 11 GND
MODEM
GND 2 10
Scan
5V
1 24V GND (Dual Beam )
24V
DADF Pick up (Conexant )
GND
GND
GND
GND
DA DF_P ICK UP_S OL 3 9
SOL
2 DA DF_P ICK UP_S OL DA DF_P ICK UP_S OL
SOL
Motor
PICKUP
Clutch nSENS_ DADF_COVER_OPEN 4 8 nSENS_DADF_COVER_OPEN
5V
nS E NS_DA DF_P _P OS 5 7 nS E NS_DA DF_P _P OS OPE(CLX-4833FR/5737FR)
N. C
N. C
nRD
GND
GND
GND
nWR
3. 3V
3. 3V
GND
GND
GND
GND
GND
24V S
DA DF_MOT _MS 1 6 6 DA DF_MOT _MS 1
nS H_1
nS H_2
nHsy nc
DADF Regi 1 24V
nRING0
DA DF_MOT _MS 2
DAT A7~
~DA TA0
nLD_O N
7
A DDR1~
~A DDR7
5 DA DF_MOT _MS 2
SOL
2 DA DF_RE GI_S OL
REGI
SOL
3. 3V _LS U
V DO_1_P
V DO _1_N
V DO_2_P
V DO _2_N
LCD DRV B˅D(CLX-5737FW)
DADF_M OT_DI R
Clutch
nDADF_M OT_E N
DADF _MOT_P LS
K EY CLI CK
24V 8
DA DF _MOT_M S1
DA DF _MOT_M S2
DA DF_EX I T_SOL
5V
S CANNER_HOM E
GND
24V
CN(1.5m m)
4
DA DF_REGI _SOL
nM _RE S ET
HOOK _DET
LD_P OWE R
CN(1.5mm)
5V 9
nCS _MO DE M
3
MT
nREA DY _LS U
5V
DA DF_PI CKUP _SOL

nI NT_MO DE M
nDADF_M OT_S LEE P
nS ENS _DADF_P _DET

nSE NS_DA DF _P_P OS
DA DF_E X IT_S OL 10
nS ENS _DADF_P _REG

nSENS_ DADF_ COVER_OPEN
1 24V 2 DA DF_E X IT_S OL STEP
DADF _MOT_CURRENT
DADF Exit S E NS_DA DF_P _S IZE
2 N.C 11 1
1
2
1
2
3
4
5
6
7
8
9
S E NS_DA DF_P _S IZE
3~
11
19
20
21
22
23
24
25
26
27
28
29
30
10
11
12
13
14
15
16
17 CLK_LS U_MOT
18
19 nLSU_M OT_E N
20
21
22
9
8
7
6
5
4
3
2
1
1
2
3
4
5
BUZZER
SOL
1
2
3
4
5
6
7
8
9
10
EXIT
SOL
10
11
12
13
14
15
16
~10
12~
~18
Clutch
9
8
7
6
5
4
3
2
1
3 DA DF_E X IT_S OL
CN(2mm) CN(1.5mm) CN(2mm)

20
19
18
17
16
15
14
13
12
11
10
CN
1 OUT1A USB_IF
2 OUT1B (OPE)
DADF Motor MT 3 OUT2A
CN(2mm)
ADF MOT
4 OUT2B
STEP
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
3
4
5
6
7
8
9
2
20
19
18
17
16
15
14
13
12
11
10
10
10
11
12
13
14
15
16
17
18
19
20
10
11
12
13
14
15
16
5V
5V
N. C
24V
N. C 24
N. C 27
nRD 22
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND 1
GND 11
GND 19
nW R 23
3. 3V 28
3. 3V 29
GND 30
24V S
B _V I N
R_V I N
nS H_1
nS H_2
G _V I N
nHs y nc
OUT1A
OUT1B
OUT2A
OUT2B
CI S_S P
nLD_O N
DAT A7~ 3~
~DA TA0 ~10
A DDR1~ 12~
~A DDR7 ~18
MAIN
3. 3V _CI S
3. 3V _CI S
CIS _CLK
3. 3V _LS U
V DO_1_P
V DO _1_N
V DO_2_P
V DO _2_N
CI S_B LE D
CIS _GLE D
CI S_RLE D
3.3V 3.3V_Cover_Open
SCA N_CT R
HOOK _DET 20
LD_P OWE R
nCS _MO DE M 21
nREA DY _LS U
nI NT_MO DE M 26
nRS T_MO DE M 25
CLK_LS U_MOT
nLSU_M OT_E N
LE D_COM MO N
DADF_M OT_DI R
nDADF_M OT_E N
DADF_M OT_P LS
DA DF _MOT_M S1
DA DF _MOT_M S2
DA DF_EX IT _SOL
DA DF _REGI _SOL
CN(2mm ) CN(FFC 1mm) CN(FFC 1mm) CN(FFC 1mm)
GND
SCA NNE R_HOME
nRS T_P ANE L
nPOWE R_SW
GND
GND
PA NEL_TX D
PA NEL_RX D
MOD_B UZ ZE R_CON
KE YCLI CK _CON
DA DF_PI CKUP _SOL
nDADF_M OT_S LEE P

SCAN_MTR CIS _IF MODE M_IF LS U_IF
nS ENS _DADF_P _DET

nSE NS_DADF _P_P OS
Front Cover
nS ENS _DADF_P _REG

nSENS_DADF_ CO VER_OPEN
DADF _M OT_CURRENT
Micro Switch CN(1.5mm) CN(1.5mm )
OP E I/F
A DF_IF 24V 1
24V 2
24V 3
3.3V 4
1 24V S 3.3V 5
24V S 12 24VS
GND 11 2 GND EEPROM 3.3V 6
THV_RE A D 10 3 THV _RE A D
3.3V DDR2 nRS T_S CF 7
nTHV_E N 9 4 nTHV _E N M24C32
5 P WM _THV S CF_TX D 8
P WM_THV 8 SDRAM S CF_RX D 9
P WM_DE V_DC 7 6 P WM _DE V_DC
7 P WM _MHV
(M24C256) N. C 10
HVP S
HVPS P WM_MHV 6
SCF_IF
Supply 8 P WM _FUS E R_B IA S (256MB) nS CF_OP T 11

P WM_FUS E R_B IA S 5
9 GND N. C 12
CN(1.5mm)
GND 4
CN(1.5mm)
GND 3 10 GND N. C 13
DEV 11 3. 3V GND 14
3.3V 2
THV 3.3V _Cover_Open 1 12 3. 3V_Cover_Open1 GND 15
3.3V_Cover_Open1 GND 16
GND 17
OPC MHV GND 18
NOR FLASH
5-4
1 GND 1
(32MB) GND
2 GND 2
Varistor 3 24V S MDI_P 3
VCLK 3
M AI N FA N
MDI_M 3
CN(2mm )
4
MDI_P 2
5
MDI_M 2
S CHORUS4 6
25MHz MDI_P 1
FAN 7
M MDI_M 1
D 8
C USB CLK MDI_P 0
MAIN 9
FUSER 1 GND MDI_M 0
2 CLK 10
BIAS R 3.3V
DIO 11
DRUM 3 LE D1
CN NETWORK_IF
CRUM
U 4 3.3V _CRUM Clock 3.3V
12
CN(2mm )
Network 13
NP C_LE D
5. System Diagram
Generator 14
M ASM3P2863 A MAIN CLK RTL8211D
FAN 1 24V S V B US 1
T DEVELOPER Unit 2 GND DM 2
CN
DP 3
SM PS F AN
CN(2m m)
SMPS
USB_IF
GND 4
12MHz
1 24V S
USB 2.0
FAN 2 NC
USB HUB USB HUB
3 GND
S MP S FAN
MIDDLE
CN(1. 5mm )
GND 1
24V OFF 2 5 GND CN(2 mm) CN(1.5 mm) CN(2mm )
SMPS 24VS CN(2mm) CN(2mm ) CN(2mm) CN(1. 5mm ) CN CN CN CN
Relay 3 4 24V OFF P_EXIT P_SIZE AIR
CN(2 mm)
CN
MP SENSOR SENSOR SENSOR E ras er TEMP
S MP S
MAIN MOTOR USB_IF USB_IF USB_IF USB_IF
Fus er ON
S MP S
5 2 24V S
Fuser ON
CN(2mm)
1
FUSER ON
GND 2 2 GND
THE RM_1
24VS
MP _CLT
3.3V S
GND
MP _SE NS
3.3V
GND
P EA PE R_EX IT
3.3V PS
GND
nSENS_BIN_ FU LL
3.3V_C_OPEN1
3.3V_C_OPEN2
3.3V S
GND
P _E mpt y
S ENS
3.3V S
GND
REG I_S ENS
3.3V S
GND
FE ED_S ENS
5V
E RA SE R_LED
A MB IE NT
GND
V BUS
DM
DP
GND
GND
MO T_DIR
PW M_MO T
MO T_REA DY
MO T_EN
GND
MO T_BRE AK
GND
GND
24VS
24VS
24VS
Pi ckup_CLT
24VS
Regi_CLT
VB US
DM
DP
GND
V BUS
DM
DP
GND
V BUS
DM
DP
GND
V BUS
DM
DP
WA KE UP
GND
24V 1 3 3 24V 1
CN
CN
SM PS
S MP S
GND 4 4 GND
1
2
1
2
3
4
5
1
2
3
1
2
3
4
5
1
2
3
4
5
6
7
8
9
1
2
1
2
1
2
3
4
5
(3. 96mm )
1
2
3
4
5
6
7
8
9
1
2
3
4
1
2
3
4
5
6
7
8
1
2
3
4
5
10
11
12
13
14
24V 2 5 24V 5 24V 2
5V_SMPS
INLET FUSER
3.3V_Cover_Open2
SOL SOL
Thermistor1 CL Ambient OPE I/F
9
8
7
6
5
4
3
2
1
10
Temp
ERASER Sensor
Regi MP MP Exit Paper Cover
Pickup EMPTY REGI FEED LED
Clutch Clutch Sensor Sensor Outbinfull Open
Clutch
Connection Diagram (SCF-483xFR/563x/573x series)
Sensor Sensor Sensor Sensor FDI Flash Direct WLAN CLX-5737FW
FUSER Unit MT Drive USB

ThermoStat BLDC CLX-5637FR
CLX -5737FW
Main Rainier Hardware Team

INLET Motor R&D Group 2
Samsung Electronics
100405
Samsung Electronics
6. Reference Information
This chapter contains the tools list, list of abbreviations used in this manual, and a guide to the location space
required when installing the printer. A de nition of test pages and Wireless Network information de nition is
also included.
6.1 Tool for Troubleshooting

The following tools are recommended safe and easy troubleshooting as described in this service manual.
• DVM (Digital Volt Meter) • Cleaning Equipments

Standard : Indicates more than 3 digits. Standard : An IPA (Isopropyl Alcohol) dry wipe tissue
or a gentle neutral detergent and lint-free
cloth.
• Driver • Vacuum Cleaner

Standard : “-” type, “+” type (M3 long, M3 short, M2
long, M2 short).
• Spring Hook
Standard : For general use
• Tweezers
Standard : For general home use, small type.
• Software (Driver) installation CD ROM

• Cotton Swab
Standard : For general home use, for medical
service.
6-1
6.2 Acronyms and Abbreviations

The table below explains abbreviations used in this service manual.
The contents of this service manual are declared with abbreviations in many parts. Please refer to the
table.
6.2.1 Acronyms
ABS Automatic Background Suppression(a FDI Foreign Device Interface
kind of copy feature) FIA Foreign Interface Attachment
APF Automatic Paper Feeder(Tray) FRU Field Replaceable Unit
BOOTP BOOTSTRAP PROTOCOL FPOT First Print Out Time
CCD Charged Coupled Device GW GateWay
CIS Contact Image Sensor HH High Temperature, High Humidity
CPM Copies Per Minute (Testing Chamber conditions)
CP Control Panel(= OPE) HPVC Halftone Printing Video Controller in the
CQ Copy Quality SPGPm (Graphic Processor for Copy)
CRU Customer Replaceable Unit IDC International Data Corp.
CRUM CRU Memory IMAP Internet Message Access Protocol
CW Center Ware IPP Internet Printing Protocols
CWDP Center Ware Device Discovery IPM Images Per Minutes
Software(Samsung equivalent of IPX Internetwork Packet Exchange
Samsung’s SyncThru) IQ Image Quality
CWIS Center Ware Internet Services ITU International Telecommunication Union
DADF Duplex Auto Document Feeder JBIG Joint Binary Image Group
(= DADH) (a kind of image data coding method)
DC Direct Connect JPEG Joint Photographic Expert Group
DDNS Dynamic Domain Name System (a kind of image data coding method)
DHCP Dynamic Host Con guration Protocol LCD Liquid Crystal Display
DLC Data Link Control LEF Long Edge Feeding
DNS Domain Name System LL Low Temperature, Low Humidity
ECM Error Correction Mode (Testing Chamber conditions)
ECP Enhanced Capability Port LPR/LPD Line Printer Daemon Protocols
e-Coil Extended Coil technology for (LPR is a TCP-based protocol)
Rapid(Fast) Fusing. LSU Laser Scanning Unit
EH&S Samsung Environment, Health, LUI Local User Interface
& Safty MCBF Mean Copy Between Failure
ESMTP Extended Simple Mail Transfer Protocol MDSP Multiple Document Single Printout
EP Electro Photography MFP Multi-Functional Product
EPC Electric Pre-Collation MH Modi ed Huffman
FCOT First Copy Out Time (a kind of image data coding method)
6-2
MIB Management Information Base RT-OS Real Time Operating System

MIME Multipurpose Internet Mail Extensions RX Receive
MR Modi ed Read S2E Scan-To-Email
(a kind of image data coding method) SAD Solid Area Density
MMR Modi ed and Modi ed Read SC Service Call
(a kind of image data coding method) SCF Second Cassette Feeder
MN std Multi-National Standard SDSP Single Document Single Printout
MSOK Master SOK(System Operation Key) SDMP Single Document Multiple Printout
MSO Mixed Size Original SDR Shut Down Rate
MP Multi Purpose SEF Short Edge Feeding
MPBF Mean Print Between Failure SIR Sacri ed(or Standard) Image Reference
MSI Multi Sheet Input SOK System Operation Key
MTBF Mean Time Between Failure sRGB Standard RGB
MTTR Mean Time To Repair (Color Coordinate System)
NCP Network Control Protocol SNMP Simple Network Management Protocol
NIC Network Interface Card TCP/IP Transmission Control Protocol/Internet
NOS Network Operating System Protocol
NN Normal Temperature, Normal Humidity TBC(or tbc) To Be Con rmed
(Testing Chamber conditions) TBD(or tbd) To Be Determined
NSDR Non-Shut Down Rate(=USDR) TIFF (Adobe & Aldus) Tagged Image File
NW Network Format
OD Optical Density TRIM Technical Retro t Interim Maintenance
OHD On Hook Dial TTM Time to Market
OSOK Optional SOK(System Operation Key) TX Transmit
OP Operational Procedure UI User Interface
PCL Printer Control Language UMC Unit Manufacturing Cost
PDF (Adobe) Portable Document Format UMR Unscheduled Maintenance Ratio
PPM Pages Per Minutes UPnP Universal Plug and Play
PQ Print Quality USB Universal Serial Bus
PS/3 PostScript Level-3 USDR Un-Shut Down Rate(=NSDR)
PVC Printing Video Controller in the XCMI Samsung’s Management Information
SPGPm(Graphic Processor for Printer) Base
QCD Quality, Cost, and Delivery WA Warranty Action
RCP Remote Control Panel WxDxH Width x Depth x Height
6-3
6.2.2 Service Parts
ACRONYM EXPLANATION
ELA HOU-SCANNER ASS’Y ELA=Electrical Assembly, HOU =Housing
MEA UNIT-COVER PA EXIT ASS’Y MEA= Mechanical Assembly, PA=Paper
PMO-TRAY EXTENTION MP NE PMO= Processing Mold
MP=Multi-Purpose(Bypass) tray
NE=for NEC (common as Samsung Halk printer)
MEC-CASSETTE ASS’Y(LETTER) MEC = Mechanic Combined unit
COVER-M-FRONT M=Mold
MPR-NAME/PLATE MPR= Machinery Press,
UNIT-LSU LSU =Laser Scanning Unit
SMPS-SMPS(V1)+HVPS SMPS =Switching Mode Power Supply
HVPS =High Voltage Power Supply
ELA-OPC UNIT SET OPC=Organic Photo-Conductive
ELA HOU-MP ASS’Y MP =Multi-Purpose (Bypass) tray
PBA MAIN-MAIN PBA =Printed circuit Board Assembly
PMO-CONNECT PAPER MFP MFP =Multi-Functional Peripheral
FAN-DC DC =Direct Current
CBF POWER STITCH GRAY CBF= Cable Form
MEA UNIT GUIDE CST PA ASS’Y CST=Cassette(Paper tray), PA=Paper
PBA LIU PBA =Printed circuit Board Assembly
LIU =Line Interface Unit for FAX
SHIELD-P_MAIN LOWER P=Press
CBF HARNESS-LIU GND LIU =Line Interface Unit for FAX
GND= Ground
PMO-COVER FEED AY AY=Assembly
PMO-COVER BRKT MOTER BRKT=Bracket
CBF HARNESS-LSU LSU =Laser Scanning Unit
IPR-SHIELD SMPS UPPERI IPR=Iron Press
PMO-BUSHING P/U.MP P/U=Pickup
MP=Multi-Purpose (Bypass) Tray
PMO-HOLDER GEAR TRr TR= Transfer Roller
SPRING ETC-TR_L TR_L=Transfer Roller - Left
PMO-CAM JAM REMOVE PMO-CAM= Processing Mold-CAM
PMO-LOCKER DEVE DEVE=Developer
6-4
ACRONYM EXPLANATION
SPECIAL SCREW(PANNEL MFP) MFP =Multi-Functional Peripheral
A/S MATERAL-DUMMY UPPER ASS’Y A/S=After-Service
MCT-GLASS ADF MCT= Machinery Cutting
ADF=Automatic Document Feeder
PPR-REGISTRATION EDGE(F) PPR= Processing Press
IPR-HOLDER GLASSI PR=Iron Press
MCT-GLASS SCANNER(LEGAL) MCT= Machinery Cutting
CBF HARNESS-OPE OPE=Operation Panel(Control Panel)
PBA SUB-D_SUB PBA SUB-D_SUB =>Sub Printed circuit Board
Assembly for the D-SUB type electrical connector
(D-Sub) a kind of the connector type(shape ‘D’)
COVER-M-CCD CABLE M=Mold
CCD=Charge Coupled Device
COVER-SCAN LOWER(UMAX) UMAX=> Supplier’s name for CCD module
ICT-INSERT SHAFTI ICT= Iron Cutting
IPR-BRK SCAN BD IPR=Iron Press
BRK=Bracket
BD= Board
CBF SIGNAL-CCD FFC CCD = Charge Coupled Device
FFC =Flexible Flat Cable
COVER-M-OPE M=Mold
OPE=Operation Panel(Control Panel)
KEY-M-COPY M=Mold
PLATE-M-ALPHA KEY M=Molde
ALPHA=Alphabet
PMO-GUIDE DP SIDE DP=Duplex
RING-CS CS= Compress
GEAR-MP/DUP DRV MP =Multi-Purpose (Bypass) tray
DUP DRV = Duplex Driver
IPR-BRKT G DUPI PR=Iron Press
BRKT=BRACKET
G= Ground
UP=Duplex
PMO-BUSHING TX(B4) TX=Transmit
PMO-TRAY CASE, MP MP=Multi-Purpose tray(Bypass tray)
6-5
ACRONYM EXPLANATION
SPRING CS RE CS=Compress
RE=Rear
SPRING CS FR CS=Compress
FR=Front
PMO-BUSHING FINGER, F F=Front
ICT-SHAFT-EXIT LOWER ID ID=Idler
SPRING-EXIT ROLL FD FD=Face Down
PMO-BUSHING_P/U,MP P/U=Pickup
MP =Multi-Purpose (Bypass) tray
PMO-HOLDER CAM MPF MPF=Multi-Purpose Feeder(=MP)
PMO-GEAR P/U MPF P/U=Pickup
MFP =Multi-Functional Peripheral
RPR-RUBBER PICK UP,MP RPR=Rubber Press
PBA SUB-MP SEN PBA SUB-MP-SEN =>Sub Printed circuit Board
Assembly for the MP-SEN(= Multi-Purpose (Bypass)
tray-Sensor)
A/S MATERAL-PICKUP,MP
FOOT-ML80
HOLDER CATCH CST MC2 MC2=>McKInley2 (Samsung Project code name)
IPR-GROUND PLATE A(OPC) OPC=Organic Photo-Conductive
ELA M/M-AUD SPEAKER ELA M/M => Electrical Assembly M/M
AUD=Audio
CBF HARNESS-OPC GND OPC GNG=Organic Photo-Conductive-Ground
IPR-GROUND PLATE SCF SCF=Second Cassette Feeder(Tray2)
PBA SUB-PTL PBA SUB-PTL=>Sub Printed circuit Board Assembly
for the PTL(= Pre Transfer Lamp)
PBA SUB-FEED+P.EMP SEN. PBA SUB-FEED=>Sub Printed circuit Board
Assembly for the feeder
EMP SEN=Empty Sensor
MOTOR STEP-MCK2(MAIN)
GEAR-EXIT/U EXIT/U=EXIT/Upper
GEAR-RDCN FEED INNER RDCN=Reduction
CBF-HARNESS-MAIN-THV WIRE THV =Transfer High Voltage
CBF-HARNESS-MAIN-MHV WIRE MHV= High Voltage(Charge Voltage)
6-6
ACRONYM EXPLANATION
GEAR-EXIT/U,ID U=Upper
ID=Idler
IPR-TERMINAL FU FU=Fuser
PMO-BEARING H/R-F H/R-F=Heat Roller - Front
BEARING-H/R L H/R-L=Heat Roller -Left
PEX-ROLLER EXIT F_UP PEX= Processing Extrude
F_UP=Face Up
SPRING ETC-P/R P/R=Pressure Roller
SPRING(R)-CAU-HOT-FU CAU-HOT-FU = Caution Hot -Fuser
PMO-ARM ACTUATOR PMO-ARM= Processing Mold Arm
LABEL(R)-HV FUSER HV=High Voltage (220V)
LABEL(R)-LV FUSER LV=Low Voltage (110V)
PPR-SPONG SHEET PPR=Plastic Press
IPR-P_PINCH(SCAN)I PR-P = Iron Press
ROLLER-REGI REGI=Registration
PBA SUB-REGI PBA SUB-REGI => Sub Printed circuit Board
Assembly for the Registration
GROUND-P_SCAN ROLLER GROUND-P =Ground-Press
IPR-GUARD C/O S/W C/O = Cover Open
S/W= Switch
MEA UNIT-TX STACKER TX =Transmit
IPR-WASHER SPRING CU CU=Curve
6-7
6.3 The Sample Pattern for the Test

The sample pattern shown in below is the standard pattern used in the factory.
The life of the toner cartridge and the printing speed are measured using the pattern shown below.
(The image is 70% of the actual A4 size).
6.3.1 A4 ISO 19752 Standard Pattern

This test page is reproduced at 70% of the normal A4 size
6-8
6.4 Selecting a location

Select a level, stable place with adequate space for air circulation. Allow extra space for opening covers and
trays.
The area should be well-ventilated and away from direct sunlight or sources of heat, cold, and humidity. Do
not set the machine close to the edge of your desk or table.
Clearance space
• Front: 482.6 mm (enough space so that the paper tray can be removed)
• Back: 180 mm (enough space for ventilation)
• Right: 100 mm (enough space for ventilation)
• Left: 100 mm (enough space for ventilation)
6-9

Service Manual: Mono Laser MFP

Uploaded by

Copyright:

Available Formats

Service Manual: Mono Laser MFP

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: Mono Laser MFP

Uploaded by

Copyright:

Available Formats

Service Manual

MONO LASER MFP

• SCX-5x3x series : 35 ppm in A4 / 37 ppm in Letter

North America : service.samsungportal.com

chapter 2 Product specifications and descriptions

chapter 3 Disassembly and Reassembly

3.3 Disassembly procedure ………………………………………… 3-3

chapter 4 Alignment and Troubleshooting

chapter 5 System Diagram

chapter 6 Reference Information

attached Parts Catalog (Exploded Views & Parts List)

1.1 Safety Warning

(2) Use only Samsung replacement parts

(3) Laser Safety Statement

1.2 Caution for safety

1.2.2 Electric Shock and Fire Safety Precautions

1.2.3 Handling Precautions

1.2.4 Assembly / Disassembly Precautions

1.2.5 Disregarding this warning may cause bodily injury

(2) Do not put nger or hair into the rotating parts.

(3) When you move the printer.

(4) Ensure the printer is installed safely.

1.3 ESD Precautions

1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain

2. Product specifications and descriptions

2.1.1 Product Overview

4. Memory (Std / Max)

7. Toner cartridge (Initial / Sales)

2.1.2 Features by models

Print, Copy, Scan, Fax ● ● ● ●

Hi-Speed USB 2.0 ● ● ● ●

IEEE 1284 Parallel ○ ○ ○ ○

Tray 2 (520 sheets) ○ ○ ○ ○

SyncThru Web Service " ● ● ● ●

( ●: Included, ○: Optional, Blank: Not available)

2.1.3.1 General Print Engine

Item SCX-483x series SCX-5x3x series

2.1.3.2 Copier specification

Item SCX-483x series SCX-5x3x series

Item SCX-483x series SCX-5x3x series

2.1.3.3 Scanner Specification

Item SCX-483x series SCX-5x3x series

2.1.3.4 Fax Specification

Item SCX-483x series SCX-5x3x series

2.1.3.5 Controller & S/W

Item SCX-483x series SCX-5x3x series

Item SCX-483x series SCX-5x3x series

Item SCX-483x series SCX-5x3x series

2.1.3.6 Paper Handling

Item SCX-483x series SCX-5x3x series

Item SCX-483x series SCX-5x3x series

Item SCX-483x series SCX-5x3x series

Item SCX-483x series SCX-5x3x series

2.1.3.8 Reliability & Service

Item SCX-483x series SCX-5x3x series

2.1.3.9 Maintenance part

Item Part Code Life

Item SCX-483x series SCX-5x3x series

Item SCX-483x series SCX-5x3x series

{X js zvs zvs

t Rainier Hardware Team