HDPE Natural

PE300/PE-HWST
(High Density Polyethylene)
Colour: Natural Material Data Sheet
Density: 0.947g/cm³

Mechanical Properties Value Unit DIN/EN/ISO

Tensile strength at yield 25 MPa 527/D638
Elongation at yield 9 % 527
Modulus of elasticity in tension 1000 MPa 527/D638
Modulus of elasticity in flexure 1000-1400 MPa 178/D790
Impact strength No br. kJ/m² 179/D256
Creep rupture strength after 1000hrs with static load 12.5 MPa -
Time yield limit for 1% elongation after 1000hrs 3 MPa -
Coefficient of friction against hardened and ground 0.29 - -
steel
P= 0.05 N/mm2, v= 0.6m/s
Ball indentation hardness 43 MPa 2039-1
Shore hardness D 64 - 868

Thermal Properties Value Unit DIN/EN/ISO

Glass transition temperature -95 °C 53736
Crystalline melting point 130 °C 53736
Service temperature (short term) 90 °C -
Service temperature (long term) 80 °C -
Coefficient of thermal expansion 13-15 10-5K 53483/D696
Specific heat 1.7-2 J/(g*K) -
Coefficient of thermal conductivity 0.35-0.43 W/(K*m) -

Electrical properties Value Unit DIN/IEC

14
Surface resistivity 10 Ohm 60093
Dielectric strength 50 kV/mm 60243-1

Other properties Value Unit DIN/EN/ISO/IEC

Water absorption @ saturation @ 23°c <0.05 % 62
Resistance to hot water, washing soda Resistant - -
Resistance to weathering No - -
Flammability (UL94) HB - -

Direct Plastics Ltd. Unit 14 Portland Business Park, Richmond Park Road, Sheffield, S13 8HS
Tel: 0114 2560889 Email: [email protected]
The following information corresponds with our current knowledge and indicates our products and possible applications. We cannot give a legally binding guarantee of certain
properties or the suitability for a specific application. Existing commercial patents must be observed. A definitive quality guarantee is given in our generalconditions of sales.
Unless otherwise stated, these values represent averages taken from injection moulding samples.
We reserve the right of technical alterations.
HDPE Black
PE300/PE-HWU
(High Density Polyethylene)
Colour: Black Material Data Sheet
Density: 0.955g/cm³

Mechanical Properties Value Unit DIN/EN/ISO

Tensile strength at yield 25 MPa 527/D638
Elongation at yield 9 % 527
Modulus of elasticity in tension 1000 MPa 527/D638
Modulus of elasticity in flexure 1000-1400 MPa 178/D790
Impact strength No br. kJ/m² 179/D256
Creep rupture strength after 1000hrs with static load 12.5 MPa -
Time yield limit for 1% elongation after 1000hrs 3 MPa -
Coefficient of friction against hardened and ground 0.29 - -
steel
P= 0.05 N/mm2, v= 0.6m/s
Ball indentation hardness 50 MPa 2039-1
Shore hardness D 64 - 868

Thermal Properties Value Unit DIN/EN/ISO

Glass transition temperature -95 °C 53736
Crystalline melting point 130 °C 53736
Service temperature (short term) 90 °C -
Service temperature (long term) 80 °C -
Coefficient of thermal expansion 13-15 10-5K 53483/D696
Specific heat 1.7-2 J/(g*K) -
Coefficient of thermal conductivity 0.35-0.43 W/(K*m) -

Electrical properties Value Unit DIN/IEC

14
Surface resistivity 10 Ohm 60093
Dielectric strength 47 kV/mm 60243-1

Other properties Value Unit DIN/EN/ISO/IEC

Water absorption @ saturation @ 23°c <0.05 % 62
Resistance to hot water, washing soda Resistant - -
Resistance to weathering Resistant - -
Flammability (UL94) HB - -

Direct Plastics Ltd. Unit 14 Portland Business Park, Richmond Park Road, Sheffield, S13 8HS
Tel: 0114 2560889 Email: [email protected]
The following information corresponds with our current knowledge and indicates our products and possible applications. We cannot give a legally binding guarantee of certain
properties or the suitability for a specific application. Existing commercial patents must be observed. A definitive quality guarantee is given in our generalconditions of sales.
Unless otherwise stated, these values represent averages taken from injection moulding samples.
We reserve the right of technical alterations.