Scribd Logo
Upload

Welcome to Scribd!

  • 194 views

    Hyundai Transys Knob Assy FR Seat H/Adj RH 88023-K3000 NNB/T9Y

    Uploaded by

    ubraghu
    This document provides work instructions for assembling a knob assembly for the front seat height adjustment of a Hyundai vehicle. The process involves 6 steps: 1) Injection molding the part and inserting an insert in the mold. 2) Picking the part from the machine and placing it on a table. 3) Trimming the gate point of the part. 4) Conducting a 100% visual inspection of the part. 5) Adding the date and shift code to the part. 6) Placing the part in a finished goods bin according to the packing standard.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd

    Hyundai Transys Knob Assy FR Seat H/Adj RH 88023-K3000 NNB/T9Y

    Uploaded by

    ubraghu
    194 views2 pages
    This document provides work instructions for assembling a knob assembly for the front seat height adjustment of a Hyundai vehicle. The process involves 6 steps: 1) Injection molding the part and inserting an insert in the mold. 2) Picking the part from the machine and placing it on a table. 3) Trimming the gate point of the part. 4) Conducting a 100% visual inspection of the part. 5) Adding the date and shift code to the part. 6) Placing the part in a finished goods bin according to the packing standard.

    Original Title

    LEVER - RH

    Copyright

    © © All Rights Reserved

    Available Formats

    XLSX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides work instructions for assembling a knob assembly for the front seat height adjustment of a Hyundai vehicle. The process involves 6 steps: 1) Injection molding the part and inserting an insert in the mold. 2) Picking the part from the machine and placing it on a table. 3) Trimming the gate point of the part. 4) Conducting a 100% visual inspection of the part. 5) Adding the date and shift code to the part. 6) Placing the part in a finished goods bin according to the packing standard.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    194 views2 pages

    Hyundai Transys Knob Assy FR Seat H/Adj RH 88023-K3000 NNB/T9Y

    Uploaded by

    ubraghu
    This document provides work instructions for assembling a knob assembly for the front seat height adjustment of a Hyundai vehicle. The process involves 6 steps: 1) Injection molding the part and inserting an insert in the mold. 2) Picking the part from the machine and placing it on a table. 3) Trimming the gate point of the part. 4) Conducting a 100% visual inspection of the part. 5) Adding the date and shift code to the part. 6) Placing the part in a finished goods bin according to the packing standard.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    of 2

    DOC NO : TRAI/PD/AWI/090

    TOPRUN AUTOMOTIVE INDIA PVT LTD EO Number : QX1IU016

    WORK INSTRUCTION EO Date : 26.04.2019

    Machine Resin / Part Assembly / Subparts


    Product
    CUSTOMER: CAR MODEL DRIVE PART DESCRIPTION / PART NUMBER TONNAGE DESCRIPTION Item No Drier Temp Part Weight Assembly Part Description Item No Qty
    Material NYLON PA6 TYP B1 INSERT 1
    Grade LS 620 AI3
    HYUNDAI KNOB ASSY FR SEAT H/ADJ RH Color NNB,T9Y As per As per
    - AI3(5DR/4DR) - 350 T Control Control
    TRANSYS 88023-K3000 NNB/T9Y Plan Plan

    No Description / Explanation PICTURE / SKETCH

    1 INJECTION MOLDING AND PUT IN INSERT AT MOLD


    2 PICK THE PART FROM MACHINE AND KEPT IN THE TABLE
    3 GATE POINT TRIM THE PART
    4 100% VISUAL INSPECTION AT THE PART
    5 DATE AND SHIFT CODE MENTION IN THE PART
    6 PLACE IT IN THE PART FROM FG BIN (AS PER PACKING STD)
    1. INJECTION MOLDING AND PUT IN 2. PICK THE PART FROM MACHINE AND
    INSERT AT MOLD KEPT IN THE TABLE 3. GATE POINT TRIM THE PART

    5.DATE AND SHIFT CODE MENTION IN 4.100% VISUAL INSPECTION AT THE


    6.PLACE IT IN THE PART FROM FG THE PART PART
    BIN (AS PER PACKING STD)

    CAUTION POINTS Q-ALERT POINTS CAUTION AREAS


    1 Every machine stop isolate the first 2 pcs for QA verifcation to setup
    bin (yellow bin or trolley)

    2 Confirmed rejects should be moved to red bin or trolley for QA Verification

    3 Check all the caution points for flash, shortfill and any other defects

    4 Any abnormalities or high rejection , escalate to supervisor Front side

    5 Ensure Steel clip and brackt steel clip locking noise during assy

    100% VISUAL INSPECTION FOR SINK


    Preparation MARK, FLOW MARK, SHINING, 100% VISUAL INSPECTION FOR
    PARTING LINE FLASH , WELD LINE, SHORT FILL, HOLE FLASH ISSUE
    1 Arrange packaging cover as per lot qty COLOUR MISMATCH
    2 Use Pen knife for deflashing
    -
    SAFETY GUARD
    Rear side

    00 QX1IU016-26.04.2019 RELEASED SOP Mr.Rajesh Mr.Satheesh Mr.Magesh


    Rev History / Change of content Prepared By Reviewed By Approved By
    DOC NO : TRAI/PD/AWI/090
    TOPRUN AUTOMOTIVE INDIA PVT LTD EO Number : QX1IU016

    WORK INSTRUCTION EO Date : 26.04.2019

    Machine Resin / Part Assembly / Subparts


    Product
    CUSTOMER: CAR MODEL DRIVE PART DESCRIPTION / PART NUMBER TONNAGE DESCRIPTION Item No Drier Temp Part Weight Assembly Part Description Item No Qty
    Material NYLON PA6 TYP B1 INSERT 1
    Grade LS 620 MS213 42
    HYUNDAI KNOB ASSY FR SEAT H/ADJ RH Color NNB,RBD As per As per
    - SU2I - 350 T Control Control
    TRANSYS 88023-BV000NNB/RBD Plan Plan

    No Description / Explanation PICTURE / SKETCH

    1 INJECTION MOLDING AND PUT IN INSERT AT MOLD


    2 PICK THE PART FROM MACHINE AND KEPT IN THE TABLE
    3 GATE POINT TRIM THE PART
    4 100% VISUAL INSPECTION AT THE PART
    5 DATE AND SHIFT CODE MENTION IN THE PART
    6 PLACE IT IN THE PART FROM FG BIN (AS PER PACKING STD)
    1. INJECTION MOLDING AND PUT IN 2. PICK THE PART FROM MACHINE AND
    INSERT AT MOLD KEPT IN THE TABLE 3. GATE POINT TRIM THE PART

    5.DATE AND SHIFT CODE MENTION IN 4.100% VISUAL INSPECTION AT THE


    6.PLACE IT IN THE PART FROM FG THE PART PART
    BIN (AS PER PACKING STD)

    CAUTION POINTS Q-ALERT POINTS CAUTION AREAS


    1 Every machine stop isolate the first 2 pcs for QA verifcation to setup
    bin (yellow bin or trolley)

    2 Confirmed rejects should be moved to red bin or trolley for QA Verification

    3 Check all the caution points for flash, shortfill and any other defects

    4 Any abnormalities or high rejection , escalate to supervisor Front side

    5 Ensure Steel clip and brackt steel clip locking noise during assy

    100% VISUAL INSPECTION FOR SINK


    Preparation MARK, FLOW MARK, SHINING, 100% VISUAL INSPECTION FOR
    PARTING LINE FLASH , WELD LINE, SHORT FILL, HOLE FLASH ISSUE
    1 Arrange packaging cover as per lot qty COLOUR MISMATCH
    2 Use Pen knife for deflashing
    -
    SAFETY GUARD
    Rear side

    00 QX1IU016-26.04.2019 RELEASED SOP Mr.Purushoth Mr.Satheesh Mr.Balaraghavan


    Rev History / Change of content Prepared By Reviewed By Approved By

    You might also like