0% found this document useful (0 votes)
80 views12 pages

IP-Installer User 'S Guide

IP-Installer is software that assigns IP addresses and configures network settings for network cameras. It can be used to configure cameras for various network environments like LAN, ADSL, and cable modem connections. The main window displays the camera's MAC address, allows configuring the system name, network settings, and applies the changes by rebooting the camera. It also allows resetting the camera to factory defaults. The guide provides detailed explanations of each setting in the IP-Installer software to help users set up and manage network cameras on the network.

Uploaded by

aw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
80 views12 pages

IP-Installer User 'S Guide

IP-Installer is software that assigns IP addresses and configures network settings for network cameras. It can be used to configure cameras for various network environments like LAN, ADSL, and cable modem connections. The main window displays the camera's MAC address, allows configuring the system name, network settings, and applies the changes by rebooting the camera. It also allows resetting the camera to factory defaults. The guide provides detailed explanations of each setting in the IP-Installer software to help users set up and manage network cameras on the network.

Uploaded by

aw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

IP-Installer User’s Guide

IP-Installer

User’s Guide

Ver. 1.0 (070918)

1 / 12
IP-Installer User’s Guide

IP-Installer Installation & Operation

I. Brief introduction of IP-Installer


Network camera needs an IP address for connection to the network (Internet/Intranet). IP-
Installer is an application program developed to assign IP address and setup network
parameters to the network camera. IP-Installer is provided in a CD supplied with the product or
it can be downloaded from our website. (http://www.cnbtec.com) This document provides
information regarding the use of IP-Installer. The location of the installer file in CD is “1.IP
INSTALLER SOFTWARE/ IPInstaller_V2_6_0_eng.exe”.

II. Main window of IP-Installer

11

12

3 13 14

15 16

17 18

1 4
2 5

10 8

19

20

21

22 7

23

24

Figure 1 IP-Installer Screen

2 / 12
IP-Installer User’s Guide

1 MAC Address
This indicates the MAC address of the selected network camera. The MAC address shown
here should be identical to the Serial No. printed on the label attached on the network
camera.

2 System Name
The user can assign a name to the network camera. The factory default setting will be
shown upon the first installation. The name can be changed by typing in a new name here
or through “Basic Setup Menu” of administration page in the viewer software: NVR or
XNVR. You can input a “System Name” up to 79 letters long.

3 List Box (Compliant Product List)


This field shows IP-Installer compliant products connected to the same subnet as the PC is
connected. If you double click any of the values shown in this window, it will activate the
parameter input window of the IP-Installer.

4 Network Mode
Network mode assigns the network environment and the way of allocating IP address to the
network camera. You can make a selection out of 6 pre-defined network modes. The
selection rule is as follows:
- LAN with static IP : LAN Static
- ADSL with static IP : ADSL Static
- Cable Modem with static IP : Cable Modem Static
- LAN with DHCP server : LAN Automatic
- ADSL with dynamic IP (PPPoE) : ADSL Automatic
- Cable Modem with dynamic IP : Cable Modem Automatic

5 Web (HTTP) Port and RTSP Port


If default Web (80) or RTSP (554) ports are not available due to the firewall on the client PC
side, you can change the port number of each of them. Port number should be a number
smaller than or equal to 65535. Examples below show cases of connecting network camera
when Web port is changed to 8080.
• Connecting to network camera from Internet Explorer :
“http://192.168.1.112:8080”
• Connecting to Admin page through Internet Explorer:

3 / 12
IP-Installer User’s Guide

“http://192.168.1.112:8080/admin.htm”
The viewer programs such as NVR or XNVR, running on the client PC use RTSP for the
connection to network camera. You also need to change the RTSP port on the client
program for correct connection, if RTSP port was changed from default value. As an
example, if you change the RTSP port to 5554 from a default value 554, you need to set the
RTSP port to 5554 on the viewer program.

If the default RTSP port cannot be used by the network camera installed in a LAN
environment connected to the external network through a router (or IP sharing device),
you need to change the RTSP port to available port number and set port forwarding
parameters on your router. Please refer to the manual of your router or IP sharing
device for more details.

Once you modify port numbers in your network camera, you have to reboot the
network camera in order to apply the modification. Rebooting can be done by clicking
on “Reboot” button.

6 IP Address, Subnet Mask, Gateway, DNS1 and DNS2


Fill these fields when “Net Mode” is „LAN Static‟, „ADSL Static‟ or „Cable Modem Static‟.
Contact the network administrator or Internet service provider (ISP) for more information.

DNS2 is used as a back-up of DNS1.

7 Username and Password


You need to fill these fields with the values registered to the ISP, when „Net. Mode‟ is „ADSL
Automatic‟. User name and password can be as long as 79 characters and 39 characters,
respectively.

8 Clone MAC
Some cable modem service providers restrict internet access through their service only
from a device having MAC address registered to them. Clone MAC field is used to enter the
registered MAC address.
button is used to copy the MAC address of the PC where the IP-Installer program is
running. Contact the ISP to figure out whether internet access is available only when MAC
address is registered.

4 / 12
IP-Installer User’s Guide

9 Network Adapter
The network adapter installed in your PC will be shown in this field.

10 Management Server
If network camera is installed in a dynamic IP environment, users need to connect to the
system through new IP address obtained by e-mail message. Registering network camera
to management server will eliminate this inconvenience by enabling the user to access the
system through host name.

11 Refresh Button
Search all the products in the subnet which are compliant with the IP-Installer.

If “Network Mode” is “LAN/ADSL/Cable Modem Static IP”, IP addresses will be shown


immediately. But if the “Network Mode” is “LAN/ADSL/Cable Modem Automatic” and if
you press Refresh button before the system obtains IP address from the server, the IP
address will be shown as “0.0.0.0”

12 Set Button
Click this button after all the network setup procedures have been completed. Select “Yes”
to the query. The network camera will be re-booted.

13 Reboot Button
Reboots the network camera. This button will be enabled when you double click on the
corresponding MAC address in the List Box.

14 Default Button
This will reset all the settings of the network camera to factory default state. Select “Yes” in
the “Information Window” inquiring if you wish to continue. You will see a message box as
shown in Figure 2 asking you to input Admin name and password to reset the system to
factory default state. Refer to Figure 3 for exemplary default values.

5 / 12
IP-Installer User’s Guide

Figure 2 Enter Admin Name and Password

Figure 3 Example factory default value after clicking on Default button

15 Admin Button (Not Available)


Connect to administration page of network camera to setup various parameters. It will be
supported in future version

Refer to the system administration part of the manual of your network camera for
default Admin Name and password. These values can be changed in Administration
mode.

16 Adapter Button
The network adapter installed in your PC will be shown in this field when the IP installer is
running on a Window 98SE.

6 / 12
IP-Installer User’s Guide

17 About Button
Displays the version of the IP installer.

18 Exit Button
Closes the IP-installer program.

19 to 24 are applied only for the products having built in wireless LAN
capability.

19 Use WLAN
Select whether to use wireless LAN or LAN. Select “ESS” to use wireless LAN.

20 WLAN Radio
Select WiFi standard for the connection.

21 WLAN SSID
Enter the SSID when using wireless LAN. SSID is set to be “default” upon factory default
selection.

22 Authentication Type
Select the type of authentication for wireless LAN.

23 Encryption Type
Determine Encryption Type. Encryption is not enabled when “Disable” is selected.

24 WLAN Key
Enter the value of WEP Key when WEP is used or Pre-Shared Key when PSK is used.

7 / 12
IP-Installer User’s Guide

III. Installation and the use of IP-Installer in Windows OS

1. Installation
Insert the CD provided with the product into the CD-ROM drive of your local PC and select the
“IP-Installer” menu. Then the program will be installed automatically. The default directory for the
installation is:

C:\Program Files\NetVideo\IP Installer\

2. Running the IP-Installer


1) Double click on the IP-Installer icon ( ) to start the IP-Installer. In case of Window98SE,
press “Refresh” button after starting the IP-Installer to find a screen as shown in Figure 4.

Figure 4 Initial screen of IP-Installer

8 / 12
IP-Installer User’s Guide

2) In case of Windows 2000 or XP, the PC will ask you to select proper network adaptor as in
Figure 5. It is needed to select right packet driver for the network adapter. If the PC is
configured to support more than one network (e.g., various MODEM, IEEE1394, etc) the PC
can crash by selecting wrong packet driver. Click on a network adapter to highlight then
press OK. Figure 5 shows a case when there is only one Ethernet adaptor which is 3Com
10/100 Mini PCI Ethernet Adapter. After selecting the proper adapter, press “Refresh” button
and the initial IP-Installer screen will be displayed as shown in Figure 4.

Figure 5 Network adapter selection screen


How to identify the network adapter :
Place the cursor on top of Network on your desktop window then press right mouse button
and select property. On a new screen you will find local connection. Place mouse cursor
on top of the local connection to display information about the network adapter.

3) Check whether the MAC address of the system you are installing is shown in the list
box.(Refer to Figure 7). (The MAC address is Serial No written on a label attached on your
network camera.)

Serial No : NCAC000041
Reg Key : 000718ffb000

Figure 6 MAC address label


Click on the MAC address of your system twice. Present network setup parameters are shown
at the rest of the screen as shown in Figure 7.

If the MAC address of your system is not shown, check the power and the
Ethernet cable connection then click “Refresh” button.

9 / 12
IP-Installer User’s Guide

3. Configuring Network
Select Network Mode from “LAN Static”, “LAN Automatic”, “ADSL Static”, “ADSL Automatic”,
“Cable Modem Static” or “Cable Modem Automatic” in accordance with the network
environment.

1) LAN Static: Select this mode when a static IP address is used in LAN. Fill in the fields of IP
Address, Subnet Mask, Gateway, DNS1 and DNS2 in Figure 7. If you don‟t know the
network configuration values, contact your network administrator.

Figure 7 Example of IP setting for static IP address

2) LAN Automatic: Select this mode when IP address is automatically allocated in LAN.

3) ADSL Static: Select this mode when you are using ADSL with a static IP address. Other
setup parameters are similar to the case of LAN Static mode. If you don‟t‟ know the
network configuration values, contact your ADSL service provider.

4) ADSL Automatic: Select this mode when ADSL connection is made through PPPoE and IP
address is assigned automatically.

10 / 12
IP-Installer User’s Guide

Figure 8 Enter the user ID and password


You need to input the user ID and Password given by your ISP.(See Figure 8).

5) Cable Modem Static: Select this mode when you are using cable modem with a static IP
address. Other set-up parameters follow the same rule as in LAN Static mode. If you do not
know the network configuration values, contact the cable modem service provider. When
MAC cloning is required, select „Clone MAC‟. Put the MAC address registered to your ISP in
the Clone MAC address box. (See Figure 9).

Pressing button copies the MAC address of your PC to the Clone MAC field.

Figure 9 Supplementary input fields for a cable modem

6) Cable Modem Automatic: Select this mode when you are using a cable modem with a
dynamic IP address. If MAC cloning is required, set Clone MAC address in the same way as
Cable Modem Static.

In “ADSL Automatic” and “Cable Modem Automatic” mode network camera should
be connected directly to the PC using the crossover cable while you run “IP-installer”.
Refer to the manual of the corresponding product for more detailed instructions.

4. Finishing the installation of the network parameters


After setting up all the parameters click on the “SET” button. You will see the following
message :
“All values will be saved, and your server will be restarted. Continue?”
Click “Yes” button to save all the values. The network camera will be rebooted.

Now, if the network camera is directly connected to the PC via crossover LAN cable, you should
unplug the crossover LAN cable from the network camera and connect the network camera to
the network device such as HUB, xDSL or Cable Modem.

11 / 12
IP-Installer User’s Guide

5. Checking the IP address of network camera


If the Network Mode is “LAN/ADSL/Cable Modem Static”(network with static IP), you can
immediately check the IP address of the network camera with the IP-Installer. But if the Network
Mode is “LAN/ADSL/Cable Modem Automatic‟” (network with dynamic IP), we recommend that
you use DDNS service.

그림 1. IP
installer의
화면 구

12 / 12

You might also like