Project Job no.
Kallang PCLTC XXX
Title Start page no./Revision
Seismic Base Shear Resistance check XXX
Calcs by Calcs date Checked by Checked date Approved by Approved date
TN 20/3/18
Pile Base Shear Estimation:
Assumption:
- Base slab is infinitely stiff to distribute the base shear evenly to all the piles.
- For marine clay, the moment point of inflection for piles are at 5m below founding level.
Pile shear and moment calculation: M
Total base shear: 18833 kN V
5m
Check moment capacity:
1200 dia
2061 kNm,
12818 kN
1400 dia
3819 kNm,
18358 kN
Project Job no.
Kallang PCLTC XXX
Title Start page no./Revision
Seismic Base Shear Resistance check XXX
Calcs by Calcs date Checked by Checked date Approved by Approved date
TN 20/3/18
1800 dia
10435 kNm,
19085 kN
Check shear resistance:
1800 dia pile
Lateral Load applied:
870kN
8.5m
90.5 mRL
Empirical calculations
L= depth to fixed point
EI= concrete EI
d= diameter of pile
Mh = soil modulus
L = (216 * 28E9* 0.9^4*pi/4/(1.8*8E6)^(1/5)= 11.7m
L=12m
Project Job no.
Kallang PCLTC XXX
Title Start page no./Revision
Seismic Base Shear Resistance check XXX
Calcs by Calcs date Checked by Checked date Approved by Approved date
TN
Diaphragm stress check
equivalent UDL = 18833/50=177 kN/m
x direction:
Diaphragm
resistance
10 36 5
Core wall base
shear applied
Diaphragm section: 700 W x 50000 D
Bending stress: 49497E6 *50000/2
/(50000^3*700/12) = 0.17 N/mm2
Shear stress: 7179E3/50000/700 = 0.2 N/mm2
Diaphragm stresses are acceptable
y direction:
equivalent UDL = 18833/50=177 kN/m
Diaphragm
resistance
50
Core wall base
shear applied
Diaphragm section: 700 W x 33000 D
Bending stress: 117813E6 *33000/2
/(33000^3*700/12) = 0.9 N/mm2
Shear stress: 9425E3/33000/700 = 0.4 N/mm2
Diaphragm stresses are acceptable
Job No. Spreadsheet Verification:
Job Title: KLPCLTC Page No. Rev. r2.4
Member: 1200 pile Made by TN Date 3/21/2018 Rev. Date: 11/5/2015
Calculation: Shear Design for circular sections with plane (discrete) or Chk by - Rev. Author: AJG
spiral links to EN1992 (with UK NA) and Arup 2011 NST 04
Inputs: Titles Variables Parameter
Outputs: General Ok (Pass) Fail
- This spreadsheet does not check the longitudinal shear is adequate, in accordance with cl. DEFINITIONS
6.2.3(7) for the assumed cotθ.
- References are to BS EN1992-1-1, using the UK NA where applicable; listed as either the
clause, expression (in brackets), or table or figures as noted.. * following an expression
reference denotes where the expression is modified as per 2011 NST 04.
INPUT DATA & GEOMETRY CHECKS Reference
Geometry and Material Parameters:
Diameter, D = 1200 mm 1.200 m
cover = 75 mm 0.075 m
Agross = 1,130,973 mm2 1.131 m2
DL = 1004 mm 1.004 m
Dw = 1037 mm 1.037 m
fck = 32 MPa
γC = 1.20 Table 2.1
εc3 = 1.75 millistrain Table 3.1
EC = fcd / εc3 = 12.95 GPa Fig 3.4
αcc for shear = 1.00 3.1.6(1)
fcd = 26.67 MPa 3.1.6(1)
ν1fcd = 13.95 MPa 6.2.3(3) SHEAR RESISTANCE Reference
αcw 1.00 6.2.3(3) Moment-shear interaction factors
αcMc = 1.000
fyw = 500 MPa Annex C αcMs,circ = 1.000
ES = 200 GPa 3.2.7(4) αcMs,spir = 1.000
γS = 1 Table 2.1
fywd = 500.0 MPa Fig 3.8 Link efficiency factors
βcircz = 0.674 m
bwz = 2
Longitudinal Reinforcement: 0.768 m
Bar diameter, db = 20 mm 0.020 m βcirc = 0.868
No. Bars, nb = 19
2
As_total = 5969 mm 0.006 m2 Resistance
ρb = 0.53 % 0.005 VRd,s (for cotθ =1) = 325 kN (6.8)*
VRd,max (for cotθ =1) = 5355 kN (6.9)*
Shear Reinforcement cotθ = 2.5000
Type = Spiral 1 VRd = 861 kN
Bar diameter, dbv = 13 mm 0.013 m
Spiral pitch, p = 250 mm 0.250 m VEd / VRd = 0.00 Pass
2
Asw / p = 531 mm / m 0.0005 m2/m
Link spacing satisfies limit set by EN1992-1-1 cl 9.5.3(3)
Design Values
VEd = 0 kN 0.000 MN
MEd / MRd = 0.41
NEd = 0 kN (compression positive)
σcp = 0.00 MPa 0.000 MN
C:\Users\Thanh.Nguyen\Desktop\Thanh (Local Files)\Projects\Holland Village\Section 1-1 LHS.xls
Section 1-1 LHS.xls 11:32 AM 3/21/2018
Job No. Spreadsheet Verification:
Job Title: KLPCLTC Page No. Rev. r2.4
Member: 1400 pile Made by TN Date 3/21/2018 Rev. Date: 11/5/2015
Calculation: Shear Design for circular sections with plane (discrete) or Chk by - Rev. Author: AJG
spiral links to EN1992 (with UK NA) and Arup 2011 NST 04
Inputs: Titles Variables Parameter
Outputs: General Ok (Pass) Fail
- This spreadsheet does not check the longitudinal shear is adequate, in accordance with cl. DEFINITIONS
6.2.3(7) for the assumed cotθ.
- References are to BS EN1992-1-1, using the UK NA where applicable; listed as either the
clause, expression (in brackets), or table or figures as noted.. * following an expression
reference denotes where the expression is modified as per 2011 NST 04.
INPUT DATA & GEOMETRY CHECKS Reference
Geometry and Material Parameters:
Diameter, D = 1400 mm 1.400 m
cover = 75 mm 0.075 m
Agross = 1,539,380 mm2 1.539 m2
DL = 1204 mm 1.204 m
Dw = 1237 mm 1.237 m
fck = 32 MPa
γC = 1.20 Table 2.1
εc3 = 1.75 millistrain Table 3.1
EC = fcd / εc3 = 12.95 GPa Fig 3.4
αcc for shear = 1.00 3.1.6(1)
fcd = 26.67 MPa 3.1.6(1)
ν1fcd = 13.95 MPa 6.2.3(3) SHEAR RESISTANCE Reference
αcw 1.00 6.2.3(3) Moment-shear interaction factors
αcMc = 1.000
fyw = 500 MPa Annex C αcMs,circ = 1.000
ES = 200 GPa 3.2.7(4) αcMs,spir = 1.000
γS = 1 Table 2.1
fywd = 500.0 MPa Fig 3.8 Link efficiency factors
βcircz = 0.804 m
bwz = 2
Longitudinal Reinforcement: 1.068 m
Bar diameter, db = 20 mm 0.020 m βcirc = 0.877
No. Bars, nb = 28
2
As_total = 8796 mm 0.009 m2 Resistance
ρb = 0.57 % 0.006 VRd,s (for cotθ =1) = 395 kN (6.8)*
VRd,max (for cotθ =1) = 7452 kN (6.9)*
Shear Reinforcement cotθ = 2.5000
Type = Spiral 1 VRd = 1034 kN
Bar diameter, dbv = 13 mm 0.013 m
Spiral pitch, p = 250 mm 0.250 m VEd / VRd = 0.00 Pass
2
Asw / p = 531 mm / m 0.0005 m2/m
Link spacing satisfies limit set by EN1992-1-1 cl 9.5.3(3)
Design Values
VEd = 0 kN 0.000 MN
MEd / MRd = 0.41
NEd = 0 kN (compression positive)
σcp = 0.00 MPa 0.000 MN
C:\Users\Thanh.Nguyen\Desktop\Thanh (Local Files)\Projects\Holland Village\Section 1-1 LHS.xls
Section 1-1 LHS.xls 11:33 AM 3/21/2018
Job No. Spreadsheet Verification:
Job Title: KLPCLTC Page No. Rev. r2.4
Member: 1800 pile Made by TN Date 3/21/2018 Rev. Date: 11/5/2015
Calculation: Shear Design for circular sections with plane (discrete) or Chk by - Rev. Author: AJG
spiral links to EN1992 (with UK NA) and Arup 2011 NST 04
Inputs: Titles Variables Parameter
Outputs: General Ok (Pass) Fail
- This spreadsheet does not check the longitudinal shear is adequate, in accordance with cl. DEFINITIONS
6.2.3(7) for the assumed cotθ.
- References are to BS EN1992-1-1, using the UK NA where applicable; listed as either the
clause, expression (in brackets), or table or figures as noted.. * following an expression
reference denotes where the expression is modified as per 2011 NST 04.
INPUT DATA & GEOMETRY CHECKS Reference
Geometry and Material Parameters:
Diameter, D = 1800 mm 1.800 m
cover = 75 mm 0.075 m
Agross = 2,544,690 mm2 2.545 m2
DL = 1599 mm 1.599 m
Dw = 1637 mm 1.637 m
fck = 32 MPa
γC = 1.20 Table 2.1
εc3 = 1.75 millistrain Table 3.1
EC = fcd / εc3 = 12.95 GPa Fig 3.4
αcc for shear = 1.00 3.1.6(1)
fcd = 26.67 MPa 3.1.6(1)
ν1fcd = 13.95 MPa 6.2.3(3) SHEAR RESISTANCE Reference
αcw 1.00 6.2.3(3) Moment-shear interaction factors
αcMc = 1.000
fyw = 500 MPa Annex C αcMs,circ = 1.000
ES = 200 GPa 3.2.7(4) αcMs,spir = 1.000
γS = 1 Table 2.1
fywd = 500.0 MPa Fig 3.8 Link efficiency factors
βcircz = 1.064 m
bwz = 2
Longitudinal Reinforcement: 1.789 m
Bar diameter, db = 25 mm 0.025 m βcirc = 0.884
No. Bars, nb = 27
2
As_total = 13254 mm 0.013 m2 Resistance
ρb = 0.52 % 0.005 VRd,s (for cotθ =1) = 533 kN (6.8)*
VRd,max (for cotθ =1) = 12480 kN (6.9)*
Shear Reinforcement cotθ = 2.5000
Type = Spiral 1 VRd = 1380 kN
Bar diameter, dbv = 13 mm 0.013 m
Spiral pitch, p = 250 mm 0.250 m VEd / VRd = 0.00 Pass
2
Asw / p = 531 mm / m 0.0005 m2/m
Link spacing satisfies limit set by EN1992-1-1 cl 9.5.3(3)
Design Values
VEd = 0 kN 0.000 MN
MEd / MRd = 0.41
NEd = 0 kN (compression positive)
σcp = 0.00 MPa 0.000 MN
C:\Users\Thanh.Nguyen\Desktop\Thanh (Local Files)\Projects\Holland Village\Section 1-1 LHS.xls
Section 1-1 LHS.xls 11:33 AM 3/21/2018
