LATHE CHUCKS AND ACCESSORIES

INDEPENDENT CHUCKS / FLANGE

PS 3
PO 3
PS 4
PO 4
DK 11
DK 12
K72
FL
FLD
 -chuck

Structure self centering chuck / steel

1. Chuck body
2. Back cover
3. Scroll plate
4. Pinion
5. Pinion half ring
6. Pinion sleeve
7. Hard master jaw
8. Hard top jaw
9. Grease nipple
10. Back cover mounting bolts
11. Chuck mounting bolt
12. Spindle locating pin
13. Back cover mounting bolts
14. Chuck wrench
15. & 16. Hard top jaw mounting bolts
17. Hard solide outside jaws
18. Hard solide inside jaws

Chuck body
- made of steel, forged, hardened and grounded

Scroll plate
- made of alloy steel, forged and hardened
- thread flanks grounded on both sides

Pinion
- made of alloy steel, hardened and grounded

Jaws
- out of high-quality alloy steel
- hardened and grouded guiding, gearing and surface

Structure self centering chuck / cast iron

1. Chuck body
2. Back cover
3. Scroll plate
4. Pinion
5. Pinion half ring
6. Pinion sleeve
7. Bohrbacke
8. Drehbacke
9. Grease nipple
10. Back cover mounting bolts
11. Chuck wrench

Chuck body
- made of cast iron, grounded

Scroll plate
- made of alloy steel, forged and hardened
- thread flanks grounded on both sides

Pinion
- made of alloy steel, hardened and grounded

Jaws
- made of high-quality alloy steel
- hardened and grouded guiding, gearing and surface

2
For technical requests you can reach us by e-mail at [email protected]
 -chuck

Clamping range for lathe chucks - PS3 / PS4 / PO3 / PO4 and DK11 / DK12
d1

d4

d1
d2

d4
d2
d3

d5

d3

d5
mm
Chuck size 80 100 125 160 200 250 315 400 500 630 800

d1 solid* 2-27 3-33 3-50 3-64 4-90 5-118 10-131 10-180 20-235 30-335 150-482
d1 reversible** - - 3-50 3-64 4-90 5-118 10-131 10-180 20-235 30-335 150-482
d2 solid 22-46 25-56 34-74 42-100 52-135 62-174 78-200 85-252 120-335 160-465 282-614
d2 reversible - - 34-76 42-97 50-130 58-165 65-182 72-228 120-410 140-590 252-736
d3 max. solid 45-69 56-87 72-115 94-154 120-202 145-256 172-299 210-380 245-476 325-630 448-780
d3 max. reversible - - 77-118 88-146 105-190 125-235 145-265 165-329 200-485 210-665 328-812
d4 max. solid 25-50 32-62 39-83 50-107 60-145 77-188 90-215 103-272 140-357 180-487 302-634
d4 max. reversible - - 52-96 62-121 72-156 86-197 103-226 127-294 110-400 120-570 240-724
d5 max. solid 48-71 62-83 80-125 98-160 130-200 160-250 190-315 230-400 276-500 345-630 468-800
d5 max. reversible - - 95-125 115-160 133-200 160-250 190-315 230-400 190-500 200-630 316-800
* Solid jaws ** 2-pieces jaws

Terms for safe use

h h h
h

1. l, z = Max. workpiece length / width

d

2. d = Workpiece diameter
3. h = Height of jaw
j step
4. Workpiece is fixed without any
l additional clamping components
z z z (e.g. rest..)
z

Chuck size 80 100 125 160 200 250 315 400 500 630 800
Workpiece dimension
l 1,2 x d 1,2 x d 1,2 x d 1,2 x d 1,2 x d 1,2 x d 1,5 x d 1,5 x d 1,5 x d 1,0 x d 1,0 x d
z 4xh 4xh 4xh 4xh 4xh 4xh 4xh 4xh 4xh 4xh 4xh
Max. gripping force
daN 1000 1700 2400 3100 3700 4600 5500 6500 7200 8000 9000
Max. speed (min-1)
Chuck cast iron (PS) 4000 3500 3200 3000 2500 2000 1500 1000 700 500 300
Chuck steel (PO) 6000 5200 4800 4500 4000 3500 2800 2000 1200 1000 450
Chuck cast iron (DK) 4000 3500 3000 2500 2000 1600 1200 1000 800 800 300
Unbalance lathe chuck steel
gcm 11 16 23 32 45 63 90 140 300 640 -

3
Current second hand machines, remnants or sample machines are available at www.bernardo.at
 Standard-3-jaw chuck Typ PS3

Centre mount according DIN 6350, cast iron

Execution:
• Standard-3-jaw chuck with high-quality
cast iron body
• With centre mount according to DIN 6350
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for turning lathe and grinding machines
• For use on machines with increased concentricity

A - chuck size 100 125 160 200 250

B 50 mm 56 mm 64,5 mm 75 mm 85 mm
C 3 mm 4 mm 4 mm 4 mm 5 mm
D 70 mm 95 mm 125 mm 160 mm 200 mm
E 20 mm 32 mm 42 mm 55 mm 76 mm
F 83 mm 108 mm 140 mm 176 mm 224 mm
G M8 M8 M10 M10 M12
H 42 mm 51 mm 70 mm 85 mm 105 mm
J 17 mm 20 mm 32 mm 29 mm 34 mm
Max. speed 3500 rpm 3200 rpm 3000 rpm 2500 rpm 2000 rpm
Weight approx. 2,8 kg 5 kg 10 kg 17,5 kg 29 kg
Art. no. 21-1001F 21-1002F 21-1003F 21-1004F 21-1005F
Price excl. VAT

A- chuck size 315 400 500 630

B 94 mm 105 mm 120 mm 135 mm
C 5 mm 5 mm 5 mm 7 mm
D 260 mm 330 mm 420 mm 545 mm
E 103 mm 136 mm 190 mm 252 mm
F 286 mm 362 mm 458 mm 586 mm
G M16 M16 M16 M16
H 125 mm 145 mm 180 mm 225 mm
J 43 mm 55 mm 60 mm 70 mm
Max. speed 1500 rpm 1000 rpm 700 rpm 500 rpm
Weight approx. 50 kg 85 kg 145 kg 250 kg
Art. no. 21-1006F 21-1007F 21-1008F 21-1009F
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws IJ-PS3 jaws OJ-PS3 MJ-PS3 TJ-PS3 SJ-PS3 STJ-PS3
Spare parts see page 12-13

4
For your closest dealer, contact us at www.bernardo.at
 Standard-3-jaw chuck Typ PS3

According to DIN 55029, cast iron

Execution:
• Standard-3-jaw chuck with high-quality
cast iron body
• With Camlock direkt mounting
according to DIN 55029
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for conventioinal turning lathes
• For use on machines with increased concentricity

Chuck size 125/D4 160/D4 160/D5 200/D4 200/D5 200/D6 250/D5 250/D6
Diameter 125 mm 160 mm 160 mm 200 mm 200 mm 200 mm 250 mm 250 mm
Taper 4 4 5 4 5 6 5 6
B 70 mm 81,5 mm 81,5 mm 91 mm 91 mm 91 mm 103,5 mm 103,5 mm
D (max.) 63,526 mm 63,526 mm 82,578 mm 63,526 mm 82,578 mm 106,390 mm 82,578 mm 106,390 mm
E 32 mm 42 mm 42 mm 55 mm 55 mm 55 mm 76 mm 76 mm
F1 82,6 mm 82,6 mm 104,8 mm 82,6 mm 104,8 mm 133,4 mm 104,8 mm 133,4 mm
Camlock stud 3 3 6 3 6 6 6 6
Max. speed 3200 rpm 3000 rpm 3000 rpm 2500 rpm 2500 rpm 2500 rpm 2000 rpm 2000 rpm
Weight approx. 5 kg 9 kg 9 kg 19 kg 19 kg 19 kg 32 kg 32 kg
Art. no. 21-1051F 21-1052F 21-1053F 21-1054F 21-1054F1 21-1055F 21-1055F1 21-1056F
Price excl. VAT

Chuck size 250/D8 315/D6 315/D8 315/D11 400/D8 400/D11 500/D8 500/D11
Diameter 250 mm 315 mm 315 mm 315 mm 400 mm 400 mm 500 mm 500 mm

Taper 8 6 8 11 8 11 8 11
B 103,5 mm 117,7 mm 117,7 mm 125 mm 128,5 mm 128,5 mm 46 mm 146 mm
D (max.) 139,734 mm 106,390 mm 139,734 mm 196,887 mm 139,734 mm 196,887 mm 139,734 mm 196,887 mm
E 76 mm 103 mm 103 mm 103 mm 136 mm 136 mm 136 mm 190 mm
F1 171,4 mm 133,4 mm 171,4 mm 235 mm 171,4 m 235 mm 171,4 mm 235 mm
Camlock stud 6 6 6 6 6 6 6 6
Max. speed 2000 rpm 1500 rpm 1500 rpm 1500 rpm 1000 rpm 1000 rpm 700 rpm 700 rpm
Weight approx. 32 kg 51 kg 51 kg 51 kg 101 kg 101 kg 150 kg 150 kg
Art. no. 21-1057F 21-1057F1 21-1058F 21-1059F 21-1060F 21-1061F 21-1062F 21-1063F
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws IJ-PS3 jaws OJ-PS3 MJ-PS3 TJ-PS3 SJ-PS3 STJ-PS3
Spare parts see page 12-13

5
For our current offers please go to our Bernardo-Newsletter
 Precision 3-jaw chuck Typ PO3

Centre mount according DIN 6350, steel

Execution:
• Precision 3-jaw chuck
• With centre mount according to DIN 6350
• Steel-design for higher speeds and longer
life span
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for turning lathe and grinding machines
• For use on machines with increased concentricity

A - chuck size 80 100 125 160 200

B 44 mm 50 mm 59,5 mm 68 mm 78 mm
C 3 mm 3 mm 4 mm 4 mm 4 mm
D 56 mm 70 mm 95 mm 125 mm 160 mm
E 16 mm 20 mm 35,5 mm 42 mm 55 mm
F 67 mm 83 mm 108 mm 140 mm 176 mm
G M6 M8 M8 M10 M10
H 32 mm 42 mm 51 mm 70 mm 85 mm
J 13 mm 17 mm 20 mm 32 mm 29 mm
Max. speed 6000 rpm 5200 rpm 4800 rpm 4500 rpm 4000 rpm
Weight approx. 1,5 kg 2,8 kg 5 kg 10 kg 17,5 kg
Art. no. 21-1011F 21-1012F 21-1013F 21-1014F 21-1015F
Price excl. VAT

A - chuck size 250 315 400 500 630

B 89 mm 96,2 mm 108 mm 119 mm 129 mm
C 5 mm 5 mm 5 mm 5 mm 7 mm
D 200 mm 260 mm 330 mm 420 mm 545 mm
E 76 mm 103 mm 136 mm 190 mm 252 mm
F 224 mm 286 mm 362 mm 458 mm 586 mm
G M12 M16 M16 M16 M16
H 105 mm 125 mm 145 mm 180 mm 225 mm
J 34 mm 43 mm 55 mm 60 mm 70 mm
Max. speed 3500 rpm 2800 rpm 2000 rpm 1200 rpm 1000 rpm
Weight approx. 29 kg 50 kg 85 kg 145 kg 250 kg
Art. no. 21-1016F 21-1017F 21-1018F 21-1018F1 21-1018F2
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws IJ-PS3 jaws OJ-PS3 MJ-PS3 TJ-PS3 SJ-PS3 STJ-PS3
Spare parts see page 12-13

6
For the most up to date information please visit www.bernado.at
 Precision 3-jaw chuck Typ PO3

According to DIN 55029, steel

Execution:
• Precision 3-jaw chuck
• With Camlock direct mount according to DIN 55029
• Steel-design for higher speeds and
longer life span
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for conventioinal turning lathes
• For use on machines with increased concentricity

Chuck size 125/D3 125/D4 160/D4 160/D5 200/D5 200/D6 250/D6 250/D8
Diameter 125 mm 125 mm 160 mm 160 mm 200 mm 200 mm 250 mm 250 mm
Taper 3 4 4 5 5 6 6 8
B 59,5 mm 59,5 mm 68 mm 68 mm 78 mm 78 mm 89 mm 89 mm
D (max.) 53,988 mm 63,526 mm 63,526 mm 82,578 mm 82,578 mm 106,390 mm 106,390 mm 139,734 mm
E 32 mm 32 mm 42 mm 42 mm 55 mm 55 mm 76 mm 76 mm
F1 70,6 mm 82,6 mm 82,6 mm 104,8 mm 104,8 mm 133,4 mm 133,4 mm 171,4 mm
Camlock stud 3 3 3 6 6 6 6 6
Max. speed 4800 rpm 4800 rpm 4500 rpm 4500 rpm 4000 rpm 4000 rpm 3500 rpm 3500 rpm
Weight approx. 5 kg 5 kg 9 kg 9 kg 19 kg 19 kg 32 kg 32 kg
Art. no. 21-1036F 21-1037F 21-1039F 21-1040F 21-1042F 21-1043F 21-1044F 21-1045F
Price excl. VAT

Chuck size 315/D6 315/D8 315/D11 400/D8 400/D11 500/D8 500/D11

Diameter 315 mm 315 mm 315 mm 400 mm 400 mm 500 mm 500 mm
Taper 6 8 11 8 11 8 11
B 96,2 mm 96,2 mm 117,7 mm 108 mm 108 mm 119 mm 119 mm
D (max.) 106,390 mm 139,734 mm 196,887 mm 139,734 mm 196,887 mm 139,734 mm 196,887 mm
E 103 mm 103 m 103 m 136 mm 136 mm 136 mm 190 mm
F1 133,4 mm 171,4 mm 235 mm 171,4 mm 235 mm 171,4 mm 235 mm
Camlock stud 6 6 6 6 6 6 6
Max. speed 2800 rpm 2800 rpm 2800 rpm 2000 rpm 2000 rpm 1200 rpm 1200 rpm
Weight approx. 51 kg 51 kg 51 kg 101 kg 101 kg 150 kg 150 kg
Art. no. 21-1046F 21-1047F 21-1048F 21-1049F 21-1050F 21-1050F1 21-1050F2
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws IJ-PS3 jaws OJ-PS3 MJ-PS3 TJ-PS3 SJ-PS3 STJ-PS3
Spare parts see page 12-13

7
Should you have any questions, please feel free to contact our service center +43 / 732 / 664015
 -lathe chuck

Concentricity of lathe chucks

A A B B B B Take care at measuring:

10 10 10 10
1. The concentricity of the machine
spindle (see table below)
2. Correct mounting of the chuck
on the spindle nose

w
D

s
d

p
C
C - = workpiece
- Maximal inbalance (A, B, C) at
L jaw openings d1, d2 und d3

mm
Chuck size 80 100 125 160 200 250 315 400 500 630 800

d1 10 10 18 18 30 30 53 53 75 75 160
d2 - 14 25 30 40 53 75 100 100 125 200
d3 14 18 30 40 53 75 100 125 125 160 250
L 40 40 60 60 80 80 120 120 160 160 160
n 40 40 50 50 80 80 125 125 200 200 325
p 60 75 100 135 162 200 252 282 282 325 500
s 35 50 62 88 96 150 210 250 300 400 400
w 63 80 100 100 160 160 250 250 400 400 500
A+B Radial runout PS/PO 0,02 0,02 0,03 0,03 0,04 0,04 0,05 0,06 0,10 0,10 0,11
C Axial runout PS/PO 0,015 0,015 0,02 0,02 0,025 0,025 0,03 0,03 0,05 0,05 0,06
A+B Radial runout DK 0,08 0,08 0,08 0,08 0,08 0,08 0,12 0,12 0,14 0,14 0,16
C Axial runout DK 0,03 0,03 0,03 0,03 0,03 0,03 0,04 0,04 0,05 0,05 0,06

a (mm)
DIN 6386 II
0.16
DK
0.14

0.12 DIN 6386 I

0.10
PS/PO

0.08
a

0.06
D

0.04

0.02

80 100 125 160 200 250 315 400 500 630 800 1000 D (mm)

Requirements for compliance the above mentioned concentricity

mm

A A I. Correct mounting of the lathe Diameter Concentricity

A chuck on the spindle nose

II. The concentricity of the PO 80-400 0,003

spindle nose must be in
accordance to the right data 500-630 0,005
B B
PS, DK 80-160 0,003
200-800 0,005

8
You are welcome to request our current special offer catalogue at www.bernardo.at
Standard 4-jaw chuck Typ PS4

Centre mount according to DIN 6350, cast iron

Execution:
• Standard 4-jaw chuck with high-quality
cast iron body
• With centre mount according to DIN 6350
• Inclusive each 1 set hard inside and hard
outside solid jaws
Application:
• Useable for turning lathe and grinding
machines as well as milling devices
• For clamping of rectangular and round
workpieces
• For using at machines with high concentricity

A - chuck size 100 125 160 200 250

B 50 mm 56 mm 64,5 mm 75 mm 85 mm
C 3 mm 4 mm 4 mm 4 mm 5 mm
D 70 mm 95 mm 125 mm 160 mm 200 mm
E 20 mm 32 mm 42 mm 55 mm 76 mm
F 83 mm 108 mm 140 mm 176 mm 224 mm
G M8 M8 M10 M10 M12
H 42 mm 51 mm 70 mm 85 mm 105 mm
J 17 mm 20 mm 32 mm 29 mm 34 mm
Max. speed 3500 rpm 3200 rpm 3000 rpm 2500 rpm 2000 rpm
Weight approx. 2,8 kg 5 kg 10 kg 17,5 kg 29 kg
Art. no. 21-1999F 21-2000F 21-2001F 21-2002F 21-2003F
Price excl. VAT

A - chuck size 315 400 500 630

B 94 mm 105 mm 120 mm 135 mm
C 5 mm 5 mm 5 mm 7 mm
D 260 mm 330 mm 420 mm 545 mm
E 103 mm 136 mm 190 mm 252 mm
F 286 mm 362 mm 458 mm 586 mm
G M16 M16 M16 M16
H 125 mm 145 mm 180 mm 225 mm
J 43 mm 55 mm 60 mm 70 mm
Max. speed 1500 rpm 1000 rpm 700 rpm 500 rpm
Weight approx. 50 kg 85 kg 145 kg 250 kg
Art. no. 21-2004F 21-2005F 21-2006F 21-2007F
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws IJ-PS4 jaws OJ-PS4 MJ-PS4 TJ-PS4 SJ-PS4 STJ-PS4
Spare parts see page 12-13

9
For technical requests you can reach us by e-mail at [email protected]
 Precision 4-jaw chuck Typ PO4

Centre mount according to DIN 6350, steel

Execution:
• Precision 4-jaw chuck
• With centre mount according to DIN 6350
• Steel design for higher speed and
longer life span
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for turning lathe and grinding machines
• For using on machines with increased concentricity

A - chuck size 125 160 200 250

B 59,5 mm 68 mm 78 mm 89 mm
C 4 mm 4 mm 4 mm 5 mm
D 95 mm 125 mm 160 mm 200 mm
E 35,5 mm 42 mm 55 mm 76 mm
F 108 mm 140 mm 176 mm 224 mm
G M8 M10 M10 M12
H 51 mm 70 mm 85 mm 105 mm
J 20 mm 32 mm 29 mm 34 mm
Max. speed 4800 rpm 4500 rpm 4000 rpm 3500 rpm
Weight approx. 5 kg 10 kg 17,5 kg 29 kg
Art. no. 21-2009F 21-2010F 21-2011F 21-2012F
Price excl. VAT

A - chuck size 315 400 500 630

B 96,2 mm 108 mm 119 mm 129 mm
C 5 mm 5 mm 5 mm 7 mm
D 260 mm 330 mm 420 mm 545 mm
E 103 mm 136 mm 190 mm 252 mm
F 286 mm 362 mm 458 mm 586 mm
G M16 M16 M16 M16
H 125 mm 145 mm 180 mm 225 mm
J 43 mm 55 mm 60 mm 70 mm
Max. speed 2800 rpm 2000 rpm 1200 rpm 1000 rpm
Weight approx. 50 kg 85 kg 145 kg 250 kg
Art. no. 21-2013F 21-2014F 21-2014F1 21-2014F2
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws IJ-PS4 jaws OJ-PS4 MJ-PS4 TJ-PS4 SJ-PS4 STJ-PS4
Spare parts see page 12-13

10
Current second hand machines, remnants or sample machines are available at www.bernardo.at
 Precision 4-jaw chuck Typ PO4

According to DIN 55029, steel

Execution:
• Precision 4-jaw chuck
• With Camlock direct mount according to DIN 55029
• Steel-design for higher speeds and
longer life span
• Inclusive each 1 set hard inside and hard
outside solid jaws
Application:
• Useable for conventional turning lathes
• For clamping of rectangular and
round workpieces
• For using at machines with
higher concentricity

Chuck size 160/D4 160/D5 200/D5 200/D6 250/D6 250/D8

Diameter 160 mm 160 mm 200 mm 200 mm 250 mm 250 mm
Taper 4 5 5 6 6 8
B 68 mm 68 mm 78 mm 78 mm 89 mm 89 mm
D (max.) 63,526 mm 82,578 mm 82,578 mm 106,390 mm 106,390 mm 139,734 mm
E 42 mm 42 mm 55 mm 55 mm 76 mm 76 mm
F1 82,6 mm 104,8 mm 104,8 mm 133,4 mm 133,4 mm 171,4 mm
Camlock studs 3 6 6 6 6 6
Max. speed 4500 rpm 4500 rpm 4000 rpm 4000 rpm 3500 rpm 3500 rpm
Weight approx. 9 kg 9 kg 19 kg 19 kg 32 kg 32 kg
Art. no. 21-2035F 21-2036F 21-2037F 21-2038F 21-2039F 21-2040F
Price excl. VAT

Chuck size 315/D6 315/D8 315/D11 400/D6 400/D8 400/D11

Diameter 315 mm 315 mm 315 mm 400 mm 400 mm 400 mm
Taper 6 8 11 6 8 11
B 96,2 mm 96,2 mm 117,7 mm 108 mm 108 mm 108 mm
D (max.) 106,390 mm 139,734 mm 196,887 mm 106,390 mm 139,734 mm 196,887 mm
E 103 m 103 m 103 m 103 mm 136 mm 136 mm
F1 133,4 mm 171,4 mm 235 mm 133,4 mm 171,4 mm 235 mm
Camlock studs 6 6 6 6 6 6
Max. speed 2800 rpm 2800 rpm 2800 rpm 2000 rpm 2000 rpm 2000 rpm
Weight approx. 51 kg 51 kg 51 kg 101 kg 101 kg 101 kg
Art. no. 21-2041F 21-2042F 21-2043F 21-2044F 21-2045F 21-2046F
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws IJ-PS4 jaws OJ-PS4 MJ-PS4 TJ-PS4 SJ-PS4 STJ-PS4
Spare parts see page 12-13

11
For your closest dealer, contact us at www.bernardo.at
 Lathe chuck accessories for PS / PO OJ / IJ / MJ

Hard outside solid jaws OJ-PS3 and OJ-PS4

Art. no. Description A B C excl. VAT

mm
21-3366 Hard outside solid jaws OJ-PS3-315 125 32 73 €
C
21-3367 Hard outside solid jaws OJ-PS3-400 145 36 92 €
21-3368 Hard outside solid jaws OJ-PS3-500 180 40 100 €
A B
21-3369 Hard outside solid jaws OJ-PS3-630 225 50 110 €

Art. no. Description A B C excl. VAT 21-3380 Hard outside solid jaws OJ-PS4-125 51 20 40 €
mm 21-3381 Hard outside solid jaws OJ-PS4-160 70 20 53 €
21-3360 Hard outside solid jaws OJ-PS3-80 32 11 28 € 21-3382 Hard outside solid jaws OJ-PS4-200 85 25 54 €
21-3361 Hard outside solid jaws OJ-PS3-100 42 15 32 € 21-3383 Hard outside solid jaws OJ-PS4-250 105 28 63 €
21-3362 Hard outside solid jaws OJ-PS3-125 51 20 40 € 21-3384 Hard outside solid jaws OJ-PS4-315 125 32 73 €
21-3363 Hard outside solid jaws OJ-PS3-160 70 20 53 € 21-3385 Hard outside solid jaws OJ-PS4-400 145 36 92 €
21-3364 Hard outside solid jaws OJ-PS3-200 85 25 54 € 21-3386 Hard outside solid jaws OJ-PS4-500 180 40 100 €
21-3365 Hard outside solid jaws OJ-PS3-250 105 28 63 € 21-3387 Hard outside solid jaws OJ-PS4-630 225 50 110 €

Hard inside solid jaws IJ-PS3 and IJ-PS4

21-3407 Hard inside solid jaws IJ-PS3-400 145 36 92 €

C 21-3408 Hard inside solid jaws IJ-PS3-500 180 40 100 €
21-3409 Hard inside solid jaws IJ-PS3-630 225 50 110 €
A B 21-3420 Hard inside solid jaws IJ-PS4-125 51 20 40 €
21-3400 Hard inside solid jaws IJ-PS3-80 32 11 28 € 21-3421 Hard inside solid jaws IJ-PS4-160 70 20 53 €
21-3401 Hard inside solid jaws IJ-PS3-100 42 15 32 € 21-3422 Hard inside solid jaws IJ-PS4-200 85 25 54 €
21-3402 Hard inside solid jaws IJ-PS3-125 51 20 40 € 21-3423 Hard inside solid jaws IJ-PS4-250 105 28 63 €
21-3403 Hard inside solid jaws IJ-PS3-160 70 20 53 € 21-3424 Hard inside solid jaws IJ-PS4-315 125 32 73 €
21-3404 Hard inside solid jaws IJ-PS3-200 85 25 54 € 21-3425 Hard inside solid jaws IJ-PS4-400 145 36 92 €
21-3405 Hard inside solid jaws IJ-PS3-250 105 28 63 € 21-3426 Hard inside solid jaws IJ-PS4-500 180 40 100 €
21-3406 Hard inside solid jaws IJ-PS3-315 125 32 73 € 21-3427 Hard inside solid jaws IJ-PS4-630 225 50 110 €

Hard master jaws MJ-PS3 and MJ-PS4

21-3286 Hard master jaws MJ-PS3-500 166 40 54 €

C
21-3287 Hard master jaws MJ-PS3-630 210 50 54,5 €

21-3300 Hard master jaws MJ-PS4-125 54 20 28 €

A
21-3301 Hard master jaws MJ-PS4-160 65 20 29 €
21-3280 Hard master jaws MJ-PS3-125 54 20 28 € 21-3302 Hard master jaws MJ-PS4-200 79 25 33 €
21-3281 Hard master jaws MJ-PS3-160 65 20 29 € 21-3303 Hard master jaws MJ-PS4-250 92 28 36 €
21-3282 Hard master jaws MJ-PS3-200 79 25 33 € 21-3304 Hard master jaws MJ-PS4-315 110 32 40 €
21-3283 Hard master jaws MJ-PS3-250 92 28 36 € 21-3305 Hard master jaws MJ-PS4-400 130 36 49 €
21-3284 Hard master jaws MJ-PS3-315 110 32 40 € 21-3306 Hard master jaws MJ-PS4-500 166 40 54 €
21-3285 Hard master jaws MJ-PS3-400 130 36 49 € 21-3307 Hard master jaws MJ-PS4-630 210 50 54,5 €

12
For our current offers please go to our Bernardo-Newsletter
 Lathe chuck accessories for PS / PO TJ / STJ / SJ

Reversible top jaws TJ-PS3 and TJ-PS4

Art. no. Description A B C excl. VAT

mm

C
21-3326 Reversible top jaws TJ-PS3-500 127 50 74,5 €

B
21-3327 Reversible top jaws TJ-PS3-630 127 52 82 €
A
21-3340 Reversible top jaws TJ-PS4-125 56 22 38,5 €
Art. no. Description A B C excl. VAT
mm 21-3341 Reversible top jaws TJ-PS4-160 67 25 41,5 €

21-3320 Reversible top jaws TJ-PS3-125 56 22 38,5 € 21-3342 Reversible top jaws TJ-PS4-200 80 27 43,5 €

21-3321 Reversible top jaws TJ-PS3-160 67 25 41,5 € 21-3343 Reversible top jaws TJ-PS4-250 95 32,5 51,5 €

21-3322 Reversible top jaws TJ-PS3-200 80 27 43,5 € 21-3344 Reversible top jaws TJ-PS4-315 110 37 55 €

21-3323 Reversible top jaws TJ-PS3-250 95 32,5 51,5 € 21-3345 Reversible top jaws TJ-PS4-400 127 42 64,5 €

21-3324 Reversible top jaws TJ-PS3-315 110 37 55 € 21-3346 Reversible top jaws TJ-PS4-500 127 50 74,5 €

21-3325 Reversible top jaws TJ-PS3-400 127 42 64,5 € 21-3347 Reversible top jaws TJ-PS4-630 127 52 82 €

Soft top jaws STJ-PS3 and STJ-PS4

21-3246 Soft top jaws STJ-PS3-500 140 42 74,5 €

21-3247 Soft top jaws STJ-PS3-630 160 52 82 €

C

21-3260 Soft top jaws STJ-PS4-125 64 22 38,5 €

A
21-3261 Soft top jaws STJ-PS4-160 78 25 41,5 €

21-3240 Soft top jaws STJ-PS3-125 64 22 38,5 € 21-3262 Soft top jaws STJ-PS4-200 90 27 43,5 €

21-3241 Soft top jaws STJ-PS3-160 78 25 41,5 € 21-3263 Soft top jaws STJ-PS4-250 106 32,5 51,5 €

21-3242 Soft top jaws STJ-PS3-200 90 27 43,5 € 21-3264 Soft top jaws STJ-PS4-315 120 37 55 €

21-3243 Soft top jaws STJ-PS3-250 106 32,5 51,5 € 21-3265 Soft top jaws STJ-PS4-400 140 42 64,5 €

21-3244 Soft top jaws STJ-PS3-315 120 37 55 € 21-3266 Soft top jaws STJ-PS4-500 140 42 74,5 €

21-3245 Soft top jaws STJ-PS3-400 140 42 64,5 € 21-3267 Soft top jaws STJ-PS4-630 160 52 82 €

Soft solid jaws SJ-PS3 and SJ-PS4

21-3207 Soft solid jaws SJ-PS3-400 145 36 92 €

21-3208 Soft solid jaws SJ-PS3-500 180 40 100 €
C

21-3209 Soft solid jaws SJ-PS3-630 225 50 110 €

A B
21-3220 Soft solid jaws SJ-PS4-125 51 20 40 €
21-3200 Soft solid jaws SJ-PS3-80 32 11 28 € 21-3221 Soft solid jaws SJ-PS4-160 70 20 53 €
21-3201 Soft solid jaws SJ-PS3-100 42 15 32 € 21-3222 Soft solid jaws SJ-PS4-200 85 25 54 €
21-3202 Soft solid jaws SJ-PS3-125 51 20 40 € 21-3223 Soft solid jaws SJ-PS4-250 105 28 63 €
21-3203 Soft solid jaws SJ-PS3-160 70 20 53 € 21-3224 Soft solid jaws SJ-PS4-315 125 32 73 €
21-3204 Soft solid jaws SJ-PS3-200 85 25 54 € 21-3225 Soft solid jaws SJ-PS4-400 145 36 92 €
21-3205 Soft solid jaws SJ-PS3-250 105 28 63 € 21-3226 Soft solid jaws SJ-PS4-500 180 40 100 €
21-3206 Soft solid jaws SJ-PS3-315 125 32 73 € 21-3227 Soft solid jaws SJ-PS4-630 225 50 110 €

13
For the most up to date information please visit www.bernado.at
 Standard-3-jaw chuck Typ DK11

Centre mount according to DIN 6350, cast iron

Execution:
• Standard 3-jaw chuck
with high-quality cast iron body
• with centre mount
according to DIN 6350
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Useable for turning lathes and
drilling devices

D - chuck size 80 100 125 160 200

D1 56 mm 70 mm 95 mm 125 mm 160 mm
D2 67 mm 83 mm 108 mm 140 mm 176 mm
D3 16 mm 22 mm 30 mm 45 mm 65 mm
H 66,5 mm 74,5 mm 84,5 mm 94 mm 109 mm
H1 50 mm 55 mm 58 mm 65 mm 75 mm
h 4 mm 3 mm 4 mm 5 mm 5 mm
Mounting bolts 3 x M6 3 x M8 3 x M8 6 x M10 6 x M10
Max. speed 4000 rpm 3500 rpm 3000 rpm 2500 rpm 2000 rpm
Weight ca. 1,9 kg 3,2 kg 5 kg 8,8 kg 15,7 kg
Art. no. 21-0750 21-0751 21-0752 21-0753 21-0754
Price excl. VAT

D - chuck size 250 315 400 500 630

D1 200 mm 260 mm 330 mm 420 mm 545 mm
D2 224 mm 286 mm 362 mm 458 mm 586 mm
D3 80 mm 100 mm 130 mm 210 mm 260 mm
H 120 mm 156,5 mm 173,5 mm 205 mm 220,5 mm
H1 80 mm 90 mm 100 mm 115 mm 135 mm
h 5 mm 6 mm 6 mm 6 mm 7 mm
Mounting bolts 6 x M12 6 x M16 6 x M16 6 x M16 6 x M16
Max. speed 1600 rpm 1200 rpm 1000 rpm 800 rpm 800 rpm
Weight ca. 26,5 kg 47 kg 73 kg 128 kg 230 kg
Art. no. 21-0755 21-0756 21-0757 21-0758 21-0759
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws DIJ-DK11 jaws DOJ-DK11 DMJ-DK11 DTJ-DK11 DSJ-DK11 DSTJ-DK11
Spare parts see page 18-19

14
Should you have any questions, please feel free to contact our service center +43 / 732 / 664015
 Standard-3-jaw chuck Typ DK11

According to DIN 55029, cast iron

Execution:
• Standard 3-jaw chuck with
high-quality cast iron body
• With Camlock direct mount
according to DIN 55029
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for conventional turning lathes

Chuck size 125/D3 125/D4 160/D4 160/D5 200/D5 200/D6

D - diameter 125 mm 125 mm 160 mm 160 mm 200 mm 250 mm
Taper 3 4 4 5 5 6

D1 (max.) 53,988 63,526 mm 63,526 mm 82,578 mm 82,578 106,390 mm

D2 70,6 mm 82,6 mm 82,6 mm 104,8 mm 104,8 mm 133,4 mm

D3 30 mm 30 mm 40 mm 40 mm 60 mm 60 mm

H1 63 mm 63 mm 74 mm 74 mm 90 mm 90 mm

Max. speed 3000 rpm 3000 rpm 2500 rpm 2500 rpm 2000 rpm 2000 rpm

Weight approx. 5 kg 5 kg 9 kg 9 kg 19 kg 19 kg

Art. no. 21-0780 21-0781 21-0782 21-0783 21-0784 21-0785

Price excl. VAT

Chuck size 250/D6 250/D8 315/D6 315/D8 315/D11 400/D8 400/D11

D - diameter 250 mm 250 mm 315 mm 315 mm 315 mm 400 mm 400 mm
Taper 6 8 6 8 11 8 11

D1 (max.) 106,390 mm 139,734 mm 106,390 mm 139,734 mm 196,887 mm 139,734 mm 196,887 mm

D2 133,4 mm 171,4 mm 133,4 mm 171,4 mm 235 mm 171,4 mm 235 mm

D3 70 mm 80 mm 100 mm 100 mm 100 mm 130 mm 130 mm

H1 96,5 mm 96,5 mm 113 mm 113 mm 115 mm 126 mm 126 mm

Max. speed 1600 rpm 1600 rpm 1200 rpm 1200 rpm 1200 rpm 1000 rpm 1000 rpm

Weight approx. 32 kg 32 kg 51 kg 51 kg 51 kg 101 kg 101 kg

Art. no. 21-0786 21-0787 21-0788 21-0789 21-0790 21-0791 21-0792

Price excl. VAT

accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws DIJ-DK11 jaws DOJ-DK11 DMJ-DK11 DTJ-DK11 DSJ-DK11 DSTJ-DK11
Spare parts see page 18-19

15
You are welcome to request our current special offer catalogue at www.bernardo.at
 Standard 4-jaw chuck Typ DK12

Centre mount according to DIN 6350, cast iron

Execution:
• Standard 4-jaw chuck
with high-quality cast iron body
• With centre mount
according to DIN 6350
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for turning lathes and grinding machines
as well as milling devices

D - chuck size 80 100 125 160 200

D1 56 mm 70 mm 95 mm 125 mm 160 mm
D2 67 mm 83 mm 108 mm 140 mm 176 mm
D3 16 mm 22 mm 30 mm 45 mm 65 mm
H 66,5 mm 74,5 mm 84,5 mm 94 mm 109 mm
H1 50 mm 55 mm 58 mm 65 mm 75 mm
h 4 mm 3 mm 4 mm 5 mm 5 mm
Mounting bolts 3 x M6 3 x M8 3 x M8 6 x M10 6 x M10
Max. speed 4000 rpm 3500 rpm 3000 rpm 2500 rpm 2000 rpm
Weight approx. 2 kg 3,2 kg 5,3 kg 9 kg 16,4 kg
Art. no. 21-0800 21-0801 21-0802 21-0803 21-0804
Price excl. VAT

D - chuck size 250 315 400 500 630

D1 200 mm 260 mm 330 mm 420 mm 545 mm
D2 224 mm 286 mm 362 mm 458 mm 586 mm
D3 80 mm 100 mm 130 mm 210 mm 260 mm
H 120 mm 156,5 mm 173,5 mm 205 mm 220,5 mm
H1 80 mm 90 mm 100 mm 115 mm 135 mm
h 5 mm 6 mm 6 mm 6 mm 7 mm
Mounting bolts 6 x M12 6 x M16 6 x M16 6 x M16 6 x M16
Max. speed 1600 rpm 1200 rpm 1000 rpm 800 rpm 800 rpm
Weight approx. 28,7 kg 49 kg 80 kg 142 kg 240 kg
Art. no. 21-0805 21-0806 21-0807 21-0808 21-0809
Price excl. VAT
accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws DIJ-DK11 jaws DOJ-DK11 DMJ-DK11 DTJ-DK11 DSJ-DK11 DSTJ-DK11
Spare parts see page 18-19

16
For technical requests you can reach us by e-mail at [email protected]
 Standard 4-jaw chuck Typ DK12

According to DIN 55029, cast iron

Execution:
• Standard 4-jaw chuck with
high-quality cast iron body
• With Camlock direct mount according to
DIN 55029
• Inclusive each 1 set hard inside and hard
outside solid jaws

Application:
• Suitable for conventional turning lathes

Chuck size 125/D3 125/D4 160/D4 160/D5 200/D4 200/D5 200/D6

D - diameter 125 mm 125 mm 160 mm 160 mm 200 mm 200 mm 200 mm
Taper 3 4 4 5 4 5 6

D1 (max.) 53,988 mm 63,526 mm 63,526 mm 82,578 mm 63,526 mm 82,578 mm 106,390 mm

D2 70,6 mm 82,6 mm 82,6 mm 104,8 mm 82,6 mm 104,8 mm 133,4 mm

D3 30 mm 30 mm 40 mm 40 mm 60 mm 60 mm 60 mm

H1 63 mm 63 mm 74 mm 74 mm 90 mm 90 mm 90 mm

Max. speed 3000 rpm 3000 rpm 2500 rpm 2500 rpm 2000 rpm 2000 rpm 2000 rpm

Weight approx. 5 kg 5 kg 9 kg 9 kg 19 kg 19 kg 19 kg

Art. no. 21-0830 21-0831 21-0832 21-0833 21-0833F 21-0834 21-0835

Price excl. VAT

Chuck size 250/D6 250/D8 315/D6 315/D8 315/D11 400/D6 400/D8 400/D11
D - diameter 250 mm 250 mm 315 mm 315 mm 315 mm 400 mm 400 mm 400 mm
Taper 6 8 6 8 11 6 8 11

D1 (max.) 106,390 mm 139,734 mm 106,390 mm 139,734 mm 196,887mm 106,390 mm 139,734 mm 196,887 mm

D2 133,4 mm 171,4 mm 133,4 mm 171,4 mm 235 mm 133,4 mm 171,4 mm 235 mm

D3 70 mm 80 mm 100 mm 100 mm 100 mm 103 mm 130 mm 130 mm

H1 96,5 mm 96,5 mm 113 mm 113 mm 115 mm 126 mm 126 mm 126 mm

Max. speed 1600 rpm 1600 rpm 1200 rpm 1200 rpm 1200 rpm 1000 rpm 1000 rpm 1000 rpm

Weight approx. 32 kg 32 kg 51 kg 51 kg 51 kg 101 kg 101 kg 101 kg

Art. no. 21-0836 21-0837 21-0838 21-0839 21-0840 21-0841 21-0842 21-0843

Price excl. VAT

accessories
accessories
Standard

Optional

1 set hard inside 1 set hard outside solid Hard master jaws Reversible top jaws Soft solid jaws Soft top jaws
solid jaws DIJ-DK11 jaws DOJ-DK11 DMJ-DK11 DTJ-DK11 DSJ-DK11 DSTJ-DK11
Spare parts see page 18-19

17
Current second hand machines, remnants or sample machines are available at www.bernardo.at
 Lathe chuck accessories for DK DOJ / DIJ / DMJ

Hard outside solid jaws DOJ-DK11 and DOJ-DK12

Art. no. Description A B C excl. VAT

C mm
21-0950 Hard out. solid jaws DOJ-DK11-500 180 46 100 €
A B 21-0951 Hard out. solid jaws DOJ-DK11-630 225 50 117 €

Art. no. Description A B C excl. VAT 21-0955 Hard out. solid jaws DOJ-DK12-80 32 12 33 €
mm 21-0956 Hard out. solid jaws DOJ-DK12-100 42 15 38 €
21-0942 Hard out. solid jaws DOJ-DK11-80 32 12 33 € 21-0957 Hard out. solid jaws DOJ-DK12-125 56 16 45 €
21-0943 Hard out. solid jaws DOJ-DK11-100 42 15 38 € 21-0958 Hard out. solid jaws DOJ-DK12-160 70 18,5 53 €
21-0944 Hard out. solid jaws DOJ-DK11-125 56 16 45 € 21-0959 Hard out. solid jaws DOJ-DK12-200 85 22 61 €
21-0945 Hard out. solid jaws DOJ-DK11-160 70 18,5 53 € 21-0960 Hard out. solid jaws DOJ-DK12-250 105 27 69 €
21-0946 Hard out. solid jaws DOJ-DK11-200 85 22 61 € 21-0961 Hard out. solid jaws DOJ-DK12-315 130 36 91 €
21-0947 Hard out. solid jaws DOJ-DK11-250 105 27 69 € 21-0962 Hard out. solid jaws DOJ-DK12-400 138 36 91 €
21-0948 Hard out. solid jaws DOJ-DK11-315 130 36 91 € 21-0963 Hard out. solid jaws DOJ-DK12-500 180 46 100 €
21-0949 Hard out. solid jaws DOJ-DK11-400 138 36 91 € 21-0964 Hard out. solid jaws DOJ-DK12-630 225 50 117 €

Hard inside solid jaws DIJ-DK11 and DIJ-DK12

21-0975 Hard inside solid jaws DIJ-DK11-400 138 36 91 €

21-0976 Hard inside solid jaws DIJ-DK11-500 180 46 100 €
C 21-0977 Hard inside solid jaws DIJ-DK11-630 225 50 117 €
21-0981 Hard inside solid jaws DIJ-DK12-80 32 12 33 €
A B 21-0982 Hard inside solid jaws DIJ-DK12-100 42 15 38 €
21-0983 Hard inside solid jaws DIJ-DK12-125 56 16 45 €
21-0968 Hard inside solid jaws DIJ-DK11-80 32 12 33 € 21-0984 Hard inside solid jaws DIJ-DK12-160 70 18,5 53 €
21-0969 Hard inside solid jaws DIJ-DK11-100 42 15 38 € 21-0985 Hard inside solid jaws DIJ-DK12-200 85 22 61 €
21-0970 Hard inside solid jaws DIJ-DK11-125 56 16 45 € 21-0986 Hard inside solid jaws DIJ-DK12-250 105 27 69 €
21-0971 Hard inside solid jaws DIJ-DK11-160 70 18,5 53 € 21-0987 Hard inside solid jaws DIJ-DK12-315 130 36 91 €
21-0972 Hard inside solid jaws DIJ-DK11-200 85 22 61 € 21-0988 Hard inside solid jaws DIJ-DK12-400 138 36 91 €
21-0973 Hard inside solid jaws DIJ-DK11-250 105 27 69 € 21-0989 Hard inside solid jaws DIJ-DK12-500 180 46 100 €
21-0974 Hard inside solid jaws DIJ-DK11-315 130 36 91 € 21-0990 Hard inside solid jaws DIJ-DK12-630 225 50 117 €

Hard master jaws DMJ-DK11 and DMJ-DK12

21-0904 Hard master jaws DMJ-DK11-500 152 45 55 €

C 21-0905 Hard master jaws DMJ-DK11-630 210 50 57 €

21-0909 Hard master jaws DMJ-DK12-125 51 16 26,5 €

A
21-0910 Hard master jaws DMJ-DK12-160 64 20 33 €

21-0898 Hard master jaws DMJ-DK11-125 51 16 26,5 € 21-0911 Hard master jaws DMJ-DK12-200 80 22 35 €

21-0899 Hard master jaws DMJ-DK11-160 64 20 33 € 21-0912 Hard master jaws DMJ-DK12-250 98 27- 38 €

21-0900 Hard master jaws DMJ-DK11-200 80 22 35 € 21-0913 Hard master jaws DMJ-DK12-315 118 36 43 €

21-0901 Hard master jaws DMJ-DK11-250 98 27 38 € 21-0914 Hard master jaws DMJ-DK12-400 114 36 46 €

21-0902 Hard master jaws DMJ-DK11-315 118 36 43 € 21-0915 Hard master jaws DMJ-DK12-500 152 45 55 €

21-0903 Hard master jaws DMJ-DK11-400 114 36 46 € 21-0916 Hard master jaws DMJ-DK12-630 210 50 57 €

18
For your closest dealer, contact us at www.bernardo.at
 Lathe chuck accessories for DK DTJ / DSTJ / DSJ

Reversible top jaws DTJ-DK11 and DTJ-DK12

Art. no. Description A B C excl. VAT

mm

B
21-0926 Reversible top jaws DTJ-DK11-500 132 45 82 €

A
21-0927 Reversible top jaws DTJ-DK11-630 131 52 87 €

21-0931 Reversible top jaws DTJ-DK12-125 53,5 20 38,3 €

Art. no. Description A B C excl. VAT
mm 21-0932 Reversible top jaws DTJ-DK12-160 67 25 41 €

21-0920 Reversible top jaws DTJ-DK11-125 53,5 20 38,3 € 21-0933 Reversible top jaws DTJ-DK12-200 80 30 45 €

21-0921 Reversible top jaws DTJ-DK11-160 67 25 41 € 21-0934 Reversible top jaws DTJ-DK12-250 95 36 53 €

21-0922 Reversible top jaws DTJ-DK11-200 80 30 45 € 21-0935 Reversible top jaws DTJ-DK12-315 118 42 61 €

21-0923 Reversible top jaws DTJ-DK11-250 95 36 53 € 21-0936 Reversible top jaws DTJ-DK12-400 130 45 70 €

21-0924 Reversible top jaws DTJ-DK11-315 118 42 61 € 21-0937 Reversible top jaws DTJ-DK12-500 132 45 82 €

21-0925 Reversible top jaws DTJ-DK11-400 130 45 70 € 21-0938 Reversible top jaws DTJ-DK12-630 131 52 87 €

Soft top jaws DSTJ-DK11 and DSTJ-DK12

21-0882 Soft top jaws DSTJ-DK11-500 140 42 74,5 €

21-0883 Soft top jaws DSTJ-DK11-630 160 52 82 €

C

21-0887 Soft top jaws DSTJ-DK12-125 64 22 38,5 €

A
21-0888 Soft top jaws DSTJ-DK12-160 78 25 41,5 €

21-0876 Soft top jaws DSTJ-DK11-125 64 22 38,5 € 21-0889 Soft top jaws DSTJ-DK12-200 90 27 45 €

21-0877 Soft top jaws DSTJ-DK11-160 78 25 41,5 € 21-0890 Soft top jaws DSTJ-DK12-250 106 32,5 51,5 €

21-0878 Soft top jaws DSTJ-DK11-200 90 27 43,5 € 21-0891 Soft top jaws DSTJ-DK12-315 120 37 55 €

21-0879 Soft top jaws DSTJ-DK11-250 106 32,5 51,5 € 21-0892 Soft top jaws DSTJ-DK12-400 140 42 64,5 €

21-0880 Soft top jaws DSTJ-DK11-315 120 37 55 € 21-0893 Soft top jaws DSTJ-DK12-500 140 42 74,5 €

21-0881 Soft top jaws DSTJ-DK11-400 140 42 64,5 € 21-0894 Soft top jaws DSTJ-DK12-630 160 52 82 €

Soft solid jaws DSJ-DK11 and DSJ-DK12

21-0857 Soft solid jaws DSJ-DK11-400 145 36 92 €

21-0858 Soft solid jaws DSJ-DK11-500 180 46 100 €
€
C

21-0859 Soft solid jaws DSJ-DK11-630 225 50 117

21-0863 Soft solid jaws DSJ-DK12-80 32 12 29 €
21-0864 Soft solid jaws DSJ-DK12-100 44 15 38 €
A B
21-0865 Soft solid jaws DSJ-DK12-125 56 16 45 €
21-0850 Soft solid jaws DSJ-DK11-80 32 12 29 € 21-0866 Soft solid jaws DSJ-DK12-160 70 18,5 53 €
21-0851 Soft solid jaws DSJ-DK11-100 44 15 38 € 21-0867 Soft solid jaws DSJ-DK12-200 85 22 57 €
21-0852 Soft solid jaws DSJ-DK11-125 56 16 45 € 21-0868 Soft solid jaws DSJ-DK12-250 105 27 61 €
21-0853 Soft solid jaws DSJ-DK11-160 70 18,5 53 € 21-0869 Soft solid jaws DSJ-DK12-315 125 36 73 €
21-0854 Soft solid jaws DSJ-DK11-200 85 22 57 € 21-0870 Soft solid jaws DSJ-DK12-400 145 36 92 €
21-0855 Soft solid jaws DSJ-DK11-250 105 27 61 € 21-0871 Soft solid jaws DSJ-DK12-500 180 46 100 €
21-0856 Soft solid jaws DSJ-DK11-315 125 36 73 € 21-0872 Soft solid jaws DSJ-DK12-630 225 50 117 €

19
For our current offers please go to our Bernardo-Newsletter
 Independent chuck Typ K72

Centre mount according to DIN 6350, cast iron

Execution:
• 4-jaw independent chuck made out of cast iron
• With centre mount according to DIN 6350
• Four separate adjustable jaws
• From a diameter of 160 mm the independent
chuck is with front-mounting
• Including milled T-slots from a diameter
of 300 mm
• Inclusive one set hard outside solid jaws

Application:
• Useable for clamping of asymmetric and
rectangular shaped workpieces on turning
lathes

D - chuck size 80 100 125 160 200 250 320

D1 55 mm 72 mm 95 mm 65 mm 125 mm 100 mm 140 mm
D2 66 mm 84 mm 108 mm 95 mm 104,8 mm 120 mm 165 mm
D3 22 mm 25 mm 30 mm 45 mm 50 mm 65 mm 95 mm
H 58 mm 77 mm 78 mm 96,5 mm 110 mm 117,5 mm 134 mm
H1 42 mm 54 mm 56 mm 65 mm 75 mm 82 mm 90 mm
h 3,5 mm 4 mm 4,5 mm 5 mm 6 mm 6 mm 6 mm
Mounting bolts 4 x M6 4 x M8 4 x M8 4 x M10 4 x M10 4 x M12 4 x M16
Max. speed 2400 rpm 2400 rpm 2000 rpm 1600 rpm 1440 rpm 1200 rpm 960 rpm
Weight approx. 1,55 kg 3,15 kg 4,90 kg 7,70 kg 15 kg 22 kg 38 kg
Art. no. 21-5000 21-5001 21-5002 21-5003 21-5004 21-5005 21-5007
Price excl. VAT

D - chuck size 400 500 630 800 1000 1250

D1 160 mm 200 mm 220 mm 250 mm 320 mm 400 mm
D2 185 mm 236 mm 258 mm 300 mm 370 mm 500 mm
D3 125 mm 160 mm 180 mm 210 mm 260 mm 305 mm
H 143 mm 161 mm 180 mm 210 mm 241 mm 256 mm
H1 95 mm 106 mm 115 mm 135 mm 150 mm 165 mm
h 8 mm 8 mm 10 mm 12 mm 15 mm 15 mm
Mounting bolts 4 x M16 4 x M20 4 x M20 8 x M20 8 x M20 8 x M20
Max. speed 640 rpm 400 rpm 320 rpm 240 rpm 180 rpm 180 rpm
Weight approx. 62 kg 90 kg 148 kg 267 kg 500 kg 800 kg
Art. no. 21-5008 21-5009 21-5010 21-5011 21-5012 21-5013
Price excl. VAT

Clamping range for independent chuck K72

D A A1 B B1

20
For the most up to date information please visit www.bernado.at
 Independent chuck Typ K72

According to DIN 55029, cast iron

Execution
• 4-jaw independent chuck made out of cast iron
• With Camlock- direct mount according to DIN 55029
• Four separate adjustable jaws
• Including milled T-slots from a diameter
of 300 mm
• Inclusive one set hard outside solid jaws

Application:
• Useable for clamping of asymmetric and
rectangular shaped workpieces on turning
lathes

Chuck size 160/D4 200/D4 200/D5 250/D5 250/D6 320/D5 320/D6 320/D8 400/D6 400/D8
D - diameter 160 mm 200 mm 200 mm 250 mm 250 mm 320 mm 320 mm 320 mm 400 mm 400 mm
Taper 4 4 5 5 6 5 6 8 6 8
D1 (max.) 63,51 mm 63,51 mm 82,56 mm 82,56 mm 106,37 mm 82,56 mm 106,37 mm 139,72 mm 106,37 mm 139,72 mm
D2 82,6 mm 82,6 mm 104,8 mm 104,8 mm 133,4 mm 104,8 mm 133,4 mm 171,4 mm 133,4 mm 171,4 mm
D3 56 mm 56 mm 56 mm 56 mm 75 mm 56 mm 75 mm 95 mm 75 mm 125 mm
H1 65 mm 75 mm 75 mm 80 mm 80 mm 90 mm 90 mm 90 mm 95 mm 95 mm
Max. speed 1600 rpm 1440 rpm 1440 rpm 1200 rpm 1200 rpm 960 rpm 960 rpm 400 rpm 640 rpm 640 rpm
Weight approx. 15,7 kg 15 kg 17 kg 26 kg 26 kg 36 kg 40 kg 38 kg 61,2 kg 70 kg
Art. no. 21-5058 21-5059 21-5060 21-5062 21-5063 21-5064 21-5065 21-5066 21-5069 21-5070
Price excl. VAT

Chuck size 400/D11 500/D8 500/D11 630/D11 630/D15 800/D11 800/D15 1000/D11 1000/D15 1250/D15
D - diameter 400 mm 500 mm 500 mm 630 mm 630 mm 800 mm 800 mm 1000 mm 1000 mm 1250 mm
Taper 11 8 11 11 15 11 15 11 15 15
D1 (max.) 196,87 mm 139,72 mm 196,87 mm 196,87 mm 285,77 mm 196,87 mm 285,77 mm 196,87 mm 285,77 mm 285,77 mm
D2 235 mm 171,4 mm 235 mm 235 mm 330,2 mm 235 mm 330,2 mm 235 mm 330,2 mm 330,2 mm
D3 160 mm 125 mm 160 mm 180 mm 180 mm 180 mm 180 mm 180 mm 280 mm 280 mm
H1 95 mm 106 mm 106 mm 115 mm 115 mm 135 mm 135 mm 150 mm 150 mm 165 mm
Max. speed 640 rpm 400 rpm 400 rpm 320 rpm 180 rpm 240 rpm 240 rpm 180 rpm 180 rpm 180 rpm
Weight approx. 70 kg 95 kg 94,4 kg 169 kg 174 kg 243 kg 257 kg 582 kg 608 kg 835 kg
Art. no. 21-5071 21-5072 21-5073 21-5074 21-5075 21-5076 21-5077 21-5078 21-5079 21-5080
Price excl. VAT

Clamping range for independent chuck K72

mm
D - Futtergröße 80 100 125 160 200 250 300 320 400 500 630 800 1000
A-A1 5-35 6-45 7-57 8-80 10-100 15-130 20-156 20-176 25-250 35-300 50-400 70-540 100-680

B-B1 35-80 40-100 48-125 50-160 63-200 80-250 100-300 100-320 118-400 125-500 160-630 200-800 250-1000

* The mentioned clamping ranges are for independent chucks with reversible jaws

21
Should you have any questions, please feel free to contact our service center +43 / 732 / 664015
 Cast iron flange FL

Short taper according to DIN 55029, rough on chuck side

Execution:
• Flange out of cast iron
• With Camlock-direct mount according to DIN 55029
• Fully machined on machine side
• Rough on chuck side

Application:
• For mounting of celf-centering chucks and
independent chucks with centre mount

Flange size 125/D3 125/D4 160/D4 160/D5 200/D4 200/D5 200/D6 250/D6 250/D8 315/D6
Diameter 125 mm 125 mm 160 mm 160 mm 200 mm 200 mm 200 mm 250 mm 250 mm 315 mm

Taper 3 4 4 5 4 5 6 6 8 6

A 127 mm 127 mm 162 mm 162 mm 203 mm 203 mm 203 mm 253 mm 253 mm 318 mm

B 28 mm 28 mm 29 mm 32 mm 29 mm 32 mm 39 mm 39 mm 42 mm 42 mm

Passage 51,5 mm 61 mm 61 mm 79,5 mm 61 mm 79,5 mm 103 mm 103 mm 136,2 mm 103 mm

Art. no. 21-4051 21-4052 21-4053 21-4054 21-4055 21-4056 21-4057 21-4058 21-4059 21-4060

Price excl. VAT

Flange size 315/D8 315/D11 400/D8 400/D11 500/D8 500/D11 500/D15 630/D8 630/D11 630/D15
Diameter 315 mm 315 mm 400 mm 400 mm 500 mm 500 mm 500 mm 630 mm 630 mm 630 mm

Taper 8 11 8 11 8 11 15 8 11 15

A 318 mm 318 mm 405 mm 405 mm 505 mm 505 mm 505 mm 635 mm 635 mm 635 mm

B 45 mm 52 mm 45 mm 49 mm 42 mm 49 mm 50 mm 42 mm 49 mm 50 mm

Passage 136,2 mm 192,8 mm 136,2 mm 192,8 mm 136,2 mm 192,8 mm 281,5 mm 136,2 mm 192,8 mm 281,5 mm

Art. no. 21-4061 21-4062 21-4063 21-4064 21-4065 21-4066 21-4067 21-4068 21-4069 21-4070

Price excl. VAT

Examples of our wide range of accessories

22
You are welcome to request our current special offer catalogue at www.bernardo.at
 Cast iron flange FLD

Short taper according to DIN 55029, chuck side pre-machined and drilled

Execution:
• Flange out of cast iron
• With Camlock-direct mount according to DIN 55029
• Fully machined on machine side
• Chuck side pre-machined and drilled

Application:
• For mounting of celf-centering chucks and
independent chucks with centre mount

Flange size 125/D3 125/D4 160/D4 160/D5 200/D4 200/D5 200/D6 250/D6 250/D8 315/D6
Diameter 125 mm 125 mm 160 mm 160 mm 200 mm 200 mm 200 mm 250 mm 250 mm 315 mm

Taper 3 4 4 5 4 5 6 6 8 6

A 125 mm 125 mm 160 mm 160 mm 200 mm 200 mm 200 mm 250 mm 250 mm 315 mm

B 26 mm 26 mm 27 mm 30 mm 27 mm 30 mm 36,5 mm 36,5 mm 39 mm 39,5 mm

Passage 51,5 mm 61 mm 61 mm 79,5 mm 61 mm 79,5 mm 103 mm 103 mm 136,2 mm 103 mm

Art. no. 21-4101 21-4102 21-4103 21-4104 21-4105 21-4106 21-4107 21-4108 21-4109 21-4110

Price excl. VAT

Flange size 315/D8 315/D11 400/D8 400/D11 500/D8 500/D11 500/D15 630/D8 630/D11 630/D15
Diameter 315 mm 315 mm 400 mm 400 mm 500 mm 500 mm 500 mm 630 mm 630 mm 630 mm

Taper 8 11 8 11 8 11 15 8 11 15

A 315 mm 315 mm 400 mm 400 mm 500 mm 500 mm 500 mm 630 mm 630 mm 630 mm

B 42 mm 52 mm 39 mm 47 mm 39 mm 47 mm 50 mm 39 mm 47 mm 50 mm

Passage 136,2 mm 192,8 mm 136,2 mm 192,8 mm 136,2 mm 192,8 mm 281,5 mm 136,2 mm 192,8 mm 281,5 mm

Art. no. 21-4111 21-4112 21-4113 21-4114 21-4115 21-4116 21-4117 21-4118 21-4119 21-4120

Price excl. VAT

Examples of our wide range of accessories

23
For technical requests you can reach us by e-mail at [email protected]
 PWA Handelsges.m.b.H.
4020 Linz | Nebingerstraße 7a | Austria
Telefon: +43.732.66 40 15 | Fax: +43.732.66 40 15-9
E-mail: [email protected] | www.bernardo.at

Imprint:
All rights reserved – reproduction of images or texts or parts of these is strictly prohibited unless prior arrangements are made.
Subject to technical and optical amendments. Product specifications subject to change without notice.
Not responsible for printing errors or mistakes.