Design of Steel Structures: CIV 342 L:2 T:2 P:0 Credits:4 Btech Iii Year 2 Sem, Lpu Syllabus

SCHOOL OF CIVIL ENGINEERING
DSS: DESIGN OF STEEL STRUCTURES

CIV 342
L:2 T:2 P:0 Credits:4
BTECH III YEAR 2 SEM, LPU Syllabus.
LECTURE: UNIT VI : Column Base

Column Bases :
 Gusseted base,
 Column base subjected to moment
Teaching Resource Developed by:
DR NISHANT YADAV
PhD (NITR), M.Tech (Structure), B.E (Civil) MBA (HR), PGDCA
GUSSETED BASE
Gusseted base plates are used for columns carrying heavy loads and loads
accompanied by moments. In this case fastenings are used to connect the base plate
and the column in the form vertical gusset plates and gusset angles. The usual
arrangement consists of a base plate, two gusset plates one over each flange of the
column and two angles. 2
GUSSETED BASE
3
Question 10.2 S.K Duggal Pg 519

A column ISHB 350@661 N/m carries an axial compressive factored
load of 1700kN. Design a suitable bolted gusset base. The base
rests on M15 grade concrete pedestal. Use 24mm dia bolts of grade
4.6 for connection
Design bearing strength of concrete = 0.45 ƒck = 6.75 N/mm2
DESIGN STEPS
Step 1. Area Required for slab base = Load / permissible stress
Area, required = 1700x103 / 6.75 = 251.85 x103 mm2
Width of base plate = Depth of the column section

+ 2 (thickness of gusset plate)
+ 80 mm to 100 mm
8/21/2020 4
Dimension of base plate
Will depend upon the gusseting material
1. Gusset plates : Assume 2 plate 16mm thick on each flange
2. Gusset Angles: Assume 2 gusset angles 150x115x15mm
MINIMUM WIDTH REQUIRED TO ACCOMMODATE :

8/21/2020
350 + 2*16 + 2*115 = 612 ~ 620 mm 5
DIMENSION OF BASE PLATE

Projection of base plate beyond flange toe = (620-612) /2 = 4 mm
Length of base plate = L = Area required= 251.85 *10 ~ 410 mm
width of plate 620
Available area should be > Required area

Provide base plate 620mm x 410mm in size
CHECK FOR BEARING PRESSURE ON CONCRETE:

P = 1700*103 = 6.68 N/mm2< 6.75 N/mm2
A 620*410
8/21/2020 6
• Step 2 COMBINED THICKNESS OF

BASE PLATE AND GUSSET ANGLE AT CRITICAL SECTION
Critical section of the base for bolted base will the as section xx
C, is the length of base plate acting as cantilever = 4 + 115 -15 = 104mm
Cantilever moment per unit

width = M1 = wc2
2
= 6.68*(104)2
2
= 36125.44 N-mm
c
8/21/2020 7
Moment capacity per unit width of the base plate and angle leg combined
Md = 1.2 fy Ze = 1.2 *250 * (bd2)
m0 1.1 6
b=1mm
d= trequired
Thickness required = 28.19mm (base plate + gusset angle leg)

Thickness of baseplate = 28.19- 15 = 13.19 = 16mm (> tf ok)
Hence, provide base plate of size : 620mm x410mm x 16mm
I= bd3
12
Y= d
2
Ze = I/ Y = bd2/6
8
• BOLTED CONNECTION
Bolted Connection
between gusset plate and column
Strength of bolt in Single shear Strength of bolt in bearing
Vdsb= fu (nnAnb + nsAsb) = Vdpb= 2.5 *fu* kb*d*t =

√3 * mb mb
= 400*10-3* (Anb) Assume, kb= 0.5
√3 * 1.25 = 2.5*400*0.5*24*12
= 65.21 kN 1.25
= 120kN
Bolt Value=Design Strength of single bolt
8/21/2020 = 65.21 kN 9
• BOLTED CONNECTION
Bolted Connection
between gusset plate and column
Strength of bolt in Single shear Strength of bolt in bearing
Shear plane is 1 only
8/21/2020 10
10
CONNECTION
Clause 7.6.2, 7.6.3 pg 50
No of Bolts required to carry/transfer load = Load on Connection

Bolt Value
Assume column end and gusset have complete bearing, 50% of the
load will be assumed to pass directly and 50% of the load will pass
through the connections.
Load on connection = 50% (1700) = 850kN
Number of Bolts required =

850/65.21 = 13 ~ 16
Number of bolts are increased from 13 to 16 to provide bolting in

regular pattern preferably divisible by 4.
8/21/2020 11
DESIGN OF GUSSET PLATE:
i. Height
ii. Length
iii. Thickness (already assumed =16mm)
Provide 8, 24mm diameter bolts on each flange in two rows.
Assume,
e = 40mm
Pitch, p= 60mm
Height of the gusset plate = 150 + 2*40+ 1*60 = 290mm
Flange of Column
Gusset plate
Gusset Angle
8/21/2020
Hence, provide base plate of size:420mmx420mmx 28mm 12
DESIGN OF GUSSET PLATE:
i. Height
ii. Length
iii. Thickness (already assumed =16mm)
Provide 8, 24mm diameter bolts on each flange in two rows.
Assume,
e = 40mm
Pitch, p= 60mm
Flange of
Height of the gusset plate Column
= 150 + 2*40+ 1*60 = 290mm
Gusset plate
Length of the gusset plate
(dimension parallel to flange)
Gusset Angle
= length of base plate =410
8/21/2020
Hence, Gusset plate of size:410mmx290mmx 16mm 13
250mm
Gusset plate 24mm dia

410x290x16 mm bolt
e=40mm
Gusset Angle
150x115x15
p=60mm
e=40mm
410mm 620mm
C=104
8/21/2020 14
DESIGN STEPS: GUSSETED BASE

The gusseted base plate may be designed as follows:
(i) Divide the factored load on the column by the design bearing strength of
concrete and find the area of the base plate required.
(ii) Choose a thickness of gusset plate (16 mm)
(iii) Gusset angle (say 150 x115 x 15) The vertical leg of the angle must have a
length to accommodate two bolt line.
(iv) To accommodate all elements the width of the base plate is determined.
Min Width of base plate = Depth of the column section + 2 (thickness of gusset plate)
Length of the base plate = Area of base plate required / Width of the base plate
(v) Bearing stress on base plate = w = Column load/Actual area of base plate
15
Thickness of base plate:

Determine the thickness of the base plate required is corresponding to the greater of
the two bending moments consideration is adopted,
Cantilever moment per unit width at the critical section
Let b = distance between the gussets
c = cantilevering projection of the base plate
M1 = wc2/2
B.M. at the Centre:

The part of the base plate between the gusset plates bends in two principal directions.
Considering two way slab action the B.M. at the centre may be taken as-
16
CONNECTIONS
• Load transmitted to one gusset plate = 1/4 (load on the column)
• Length of weld on one gusset plate to connect with the column = Load on one
gusset plate/Strength of weld per mm length
• The height of the gusset plate may be selected to accommodate the weld. The
height of the gusset plate may be reduced to 100 mm at the ends. Similarly,
provide also weld connection between the gusset plate and the base plate.
8/21/2020 17

Design of Steel Structures: CIV 342 L:2 T:2 P:0 Credits:4 Btech Iii Year 2 Sem, Lpu Syllabus

Uploaded by

Copyright:

Available Formats

Design of Steel Structures: CIV 342 L:2 T:2 P:0 Credits:4 Btech Iii Year 2 Sem, Lpu Syllabus

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design of Steel Structures: CIV 342 L:2 T:2 P:0 Credits:4 Btech Iii Year 2 Sem, Lpu Syllabus

Uploaded by

Copyright:

Available Formats

SCHOOL OF CIVIL ENGINEERING

DSS: DESIGN OF STEEL STRUCTURES

LECTURE: UNIT VI : Column Base

Teaching Resource Developed by:

Question 10.2 S.K Duggal Pg 519

Design bearing strength of concrete = 0.45 ƒck = 6.75 N/mm2

Width of base plate = Depth of the column section

MINIMUM WIDTH REQUIRED TO ACCOMMODATE :

DIMENSION OF BASE PLATE

Available area should be > Required area

CHECK FOR BEARING PRESSURE ON CONCRETE:

• Step 2 COMBINED THICKNESS OF

Cantilever moment per unit

Thickness required = 28.19mm (base plate + gusset angle leg)

Hence, provide base plate of size : 620mm x410mm x 16mm

Strength of bolt in Single shear Strength of bolt in bearing

Vdsb= fu (nnAnb + nsAsb) = Vdpb= 2.5 *fu* kb*d*t =

Strength of bolt in Single shear Strength of bolt in bearing

Shear plane is 1 only

No of Bolts required to carry/transfer load = Load on Connection

Load on connection = 50% (1700) = 850kN

Number of Bolts required =

Number of bolts are increased from 13 to 16 to provide bolting in

Gusset plate 24mm dia

DESIGN STEPS: GUSSETED BASE

Thickness of base plate:

B.M. at the Centre:

You might also like

Vdsb= fu (nnAnb + nsAsb) = Vdpb= 2.5 fu kbdt =