Scribd
Upload
502 views1 page

Fanuc 0 CNC Identification Sheet

This document provides information to determine the model type of a Fanuc 0 series CNC control. The master board number found on the main circuit board and the software version displayed upon powering up with E-stop engaged can be used. The master board numbers correspond to different Fanuc 0 models, with the 0-MA and 0-TA having a maximum of 120M memory, the 0-MB and 0-TB having 320M, and the 0-MC and 0-TC also having 320M. Basic procedures for installing a memory upgrade kit are also outlined.

Uploaded by

anthony soliz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
502 views1 page

Fanuc 0 CNC Identification Sheet

This document provides information to determine the model type of a Fanuc 0 series CNC control. The master board number found on the main circuit board and the software version displayed upon powering up with E-stop engaged can be used. The master board numbers correspond to different Fanuc 0 models, with the 0-MA and 0-TA having a maximum of 120M memory, the 0-MB and 0-TB having 320M, and the 0-MC and 0-TC also having 320M. Basic procedures for installing a memory upgrade kit are also outlined.

Uploaded by

anthony soliz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Determination of Fanuc 0 Model Types

To determine the version of the Fanuc 0 series CNC Control, check the master board number and/or the
software version. The Master board number is found on the top left side of the main circuit board, usually
mounted in the control cabinet that has the daughter card attached. It should not be confused with
“A02B-????-????” numbers, which are Fanuc’s ordering numbers and are usually found on a sticker
above the master board. Use the following table to determine which unit you have.

You can determine the software version by powering-up the control with E-stop active (button depressed).
The control should hang on the software version screen (in the lower right corner of this screen, you will
see the servo version number as well).

As far as difficulty with installation, the process requires the following basic procedures:

1. Back-up everything (using a computer and following Memex kit instructions);


2. Write down NC system parameters, PMC parameters (in the Diagnostics area) and options;
3. Power off and install the Memex memory components in the designated empty sockets;
4. Power up holding RESET & DELETE keys to re-initialize and erases all memory;
5. Use special procedures to reload data in the proper sequence (as per kit instructi ons);
6. Verify operation of the machine, and you are done!

1985 / 1986 Fanuc 0-MA and Fanuc 0-TA 120M maximum battery backed resident memory.
1987 / 1989 Fanuc 0-MB and Fanuc 0-TB 320M maximum battery backed resident memory.
1990 / 1998 Fanuc 0- MC and Fanuc 0-TC 320M maximum battery backed resident memory.

FANUC 0-A Masterboards; A16B-1010-0150 (Analog) Max. 120 Meters (48K)


A16B-1010-0210 (Digital) (Software Ver 400, 402, etc)
A16B-1010-0240 (0-Mate)

FANUC 0-B Masterboards; A16B-1010-0280 (3/4 Axis) Max. 320 Meters (128K)
A16B-1010-0281 (2 Axis) (Software Ver 415, 815, etc)
A16B-1010-0285 (3/4 Axis)
A16B-1010-0288 (2 Axis)

FANUC 0-C Masterboards; A20B-2000-0179 (32Bit Version) Max. 320 Meters (128K)
A20B-2000-0180 (32Bit Version) (Software Ver 460, 462, 465
A20B-1002-0360 or 0380 (16 Bit Ver) 660,662,690,665,880,135, etc)
A20B-1003-0750 (16Bit Version)

File: /ISO9000/Docs/F100051D – MAI Determination of Fanuc 0 Model Types.doc

Memex Automation Inc., Suite 200 - 3425 Harvester Rd, Burlington, Ontario Canada L7N 2G1
Phone: (905) 635-3040 Fax: (905) 631-9640
www.memex.ca

You might also like