155Mbps SFP Optical Transceiver, 20km Reach: AOP-303-R20 (D)
155Mbps SFP Optical Transceiver, 20km Reach: AOP-303-R20 (D)
155Mbps SFP Optical Transceiver, 20km Reach: AOP-303-R20 (D)
AOP-303-R20(D)
AOP-303-R20(D)
155Mbps SFP Optical Transceiver, 20km Reach
Features
z Up to 155Mbps data-rate
z 1310nm FP laser and PIN photodetector for 20km
transmission with SMF
z Compliant with SFP MSA and SFF-8472 with duplex LC
receptacle
z Digital Diagnostic Monitoring:
Internal Calibration or External Calibration
z Compatible with RoHS
z +3.3V single power supply
z Operating case temperature:
Standard : 0 to +70°C
Industrial : -40 to +85°C
Applications
z SDH STM-1, S-1.1,L-1.1, L-1.2
z SONET OC-3 IR1,LR1,LR2
z Router/Server interface
z Other optical transmission systems
Description
The SFP transceivers are high performance, cost effective modules supporting dual data-rate of
125Mbps/155Mbps and 20km transmission distance with SMF.
The transceiver consists of three sections: a FP laser transmitter, a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety
requirements.
The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further
AscentOptics 1
Product Datasheet
AOP-303-R20(D)
TD+/-
TxFault LD Driver LD
TxDis
LOS
Post Amp PIN+TIA
RD+/-
Operating Humidity - 5 85 %
AscentOptics 2
Product Datasheet
AOP-303-R20(D)
Extinction Ratio ER 9 dB
Receiver
LOS Hysteresis 1 4 dB
Low 0.8 V
Notes:
1. The optical power is launched into SMF.
2. PECL input, internally AC-coupled and terminated.
23 -10
3. Measured with a PRBS 2 -1 test pattern @155Mbps, BER ≤1×10 .
4. Internally AC-coupled.
AscentOptics 3
Product Datasheet
AOP-303-R20(D)
Diagnostics
Table 5 – Diagnostics Specification
Parameter Range Unit Accuracy Calibration
0 to +70
Temperature °C ±3°C Internal / External
-40 to +85
The diagnostic information with internal calibration or external calibration all are implemented, including
received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage
monitoring and temperature monitoring.
AscentOptics 4
Product Datasheet
AOP-303-R20(D)
The digital diagnostic memory map specific data field defines as following.
Pin Definitions
Pin Diagram
AscentOptics 5
Product Datasheet
AOP-303-R20(D)
AscentOptics 6
Product Datasheet
AOP-303-R20(D)
Pin Descriptions
Pin Signal Name Description Plug Seq. Notes
1 VEET Transmitter Ground 1
2 TX FAULT Transmitter Fault Indication 3 Note 1
3 TX DISABLE Transmitter Disable 3 Note 2
4 MOD_DEF(2) SDA Serial Data Signal 3 Note 3
5 MOD_DEF(1) SCL Serial Clock Signal 3 Note 3
6 MOD_DEF(0) TTL Low 3 Note 3
7 Rate Select Not Connected 3
8 LOS Loss of Signal 3 Note 4
9 VEER Receiver ground 1
10 VEER Receiver ground 1
11 VEER Receiver ground 1
12 RD- Inv. Received Data Out 3 Note 5
13 RD+ Received Data Out 3 Note 5
14 VEER Receiver ground 1
15 VCCR Receiver Power Supply 2
16 VCCT Transmitter Power Supply 2
17 VEET Transmitter Ground 1
18 TD+ Transmit Data In 3 Note 6
19 TD- Inv. Transmit Data In 3 Note 6
20 VEET Transmitter Ground 1
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage
between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low
state, the output will be pulled to less than 0.8V.
2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a
4.7k~10kΩ resistor. Its states are:
Low (0 to 0.8V): Transmitter on
(>0.8V, < 2.0V): Undefined
High (2.0 to 3.465V): Transmitter Disabled
Open: Transmitter Disabled
3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board.
The pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
4) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage between 2.0V and
Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to
less than 0.8V.
5) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be
terminated with 100Ω (differential) at the user SERDES.
6) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential
termination inside the module.
AscentOptics 7
Product Datasheet
AOP-303-R20(D)
Mechanical Dimensions
AscentOptics 8
Product Datasheet
AOP-303-R20(D)
Ordering information
Part Number Product Description
AOPC-303-R20 CWDM, 1.25Gbps, 40km, 0ºC ~ +70ºC without DDM
AOPC-303-R20(D) CWDM, 1.25Gbps, 40km, 0ºC ~ +70ºC, with DDM
AscentOptics reserves the right to make changes to the product(s) or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the
sale of any such product(s) or information. Edition: Apr. 2009 Published by Ascent Optics Co.,Ltd. Copyright ©
Ascent Optics All Rights Reserved.
E-mail: sales@ascentoptics.com
Web : http://www.ascentoptics.com
AscentOptics 9