FSP-951 Series Addressable Photoelectric Smoke Detectors

The NOTIFIER® FSP-951 Series intelligent plug-in smoke detectors

are designed for both performance and aesthetics, and are direct
replacements for the FSP-851 Series. A new modern, sleek, con-
temporary design and enhanced optical sensing chamber is engi-
neered to sense smoke produced by a wide range of combustion
sources in accordance with more stringent code standards.
The FSP-951 Series detector sensitivity can be programmed in the
control panel software. Sensitivity is continuously monitored and
reported to the panel. Point ID capability allows each detector’s
address to be set with rotary, decimal address switches, providing
exact detector location for selective maintenance when chamber
contamination reaches an unacceptable level. Dual electronic
thermistors add 135°F (57°C) fixed temperature thermal sensing on
the FSP-951T. The FSP-951R is a remote test capable detector for
use with DNR Series duct detector housings. FSP-951 series detec-
tors are available for both FlashScan® and CLIP applications as
designated.

Features
SLC LOOP: • Separate base allows interchange of photoelectric, ionization and
• Two-wire SLC loop connection thermal sensors
• Unit uses base for wiring OPTIONS:
• Compatible with FlashScan® and CLIP protocol systems • Optional relay, isolator, and sounder bases
• Stable communication technique with noise immunity
Installation
ADDRESSING:
FSP-951 Series plug-in intelligent smoke detectors use a detach-
• Addressable by device able base to simplify installation, service and maintenance. Installa-
• Rotary, decimal addressing tion instructions are shipped with each detector.
(Refer to the NOTIFIER panel manuals for device capacity.) Mount detector base (all base types) on an electrical backbox which
ARCHITECTURE: is at least 1.5" (3.81 cm) deep. For a chart of compatible junction
boxes, see DN-60054.
• Sleek, low-profile, stylish design
NOTE: Because of the inherent supervision provided by the SLC loop,
• Unique single-source design to respond quickly and dependably
end-of-line resistors are not required. Wiring “T-taps” or branches are
to a broad range of fires
permitted for Class “B” wiring only.
• Integral communications and built-in device-type identification When using relay or sounder bases, consult the ISO-X(A) installation
• Built-in tamper resistant feature sheet I56-1380 for device limitations between isolator modules and isola-
tor bases.
• Remote test feature from the panel
• Walk test with address display (an address on 121 will blink the Construction
detector LED: 12-[pause]-1(FlashScan systems only)
These detectors are constructed of fire-resistant plastic. The FSP-
• Built-in functional test switch activated by external magnet 951 Series plug-in intelligent smoke detectors are designed to com-
• Removable cover and insect-resistant screen for simple field mercial standards and offer an attractive appearance.
cleaning
• Expanded color options Operation
OPERATION: Each FSP-951 Series detector uses one of the panel’s addresses
(total limit is panel dependent) on the NOTIFIER Signaling Line Cir-
• Designed to meet UL 268 7th Edition cuit (SLC). It responds to regular polls from the control panel and
• Factory preset at 1.5% nominal sensitivity for panel alarm thresh- reports its type and the status. If it receives a test command from the
old level panel (or a local magnet test), it stimulates its electronics and
• LED “blinks” when the unit is polled (communicating with the fire reports an alarm. It blinks its LEDs when polled and turns the LEDs
panel) and latches in alarm. on when commanded by the panel. The FSP-951 Series offers fea-
• Low standby current tures and performance that represent the latest in smoke detector
technology.
MECHANICALS:
• Sealed against back pressure Product Line Information
• SEMS screws for wiring of the separate base NOTE: “-IV” suffix indicates CLIP and FlashScan device.
• Designed for direct-surface or electrical-box mounting FSP-951: White, low-profile intelligent photoelectric sensor, FlashS-
• Plugs into separate base for ease of installation and maintenance can only
FSP-951A: Same as FSP-951 but with ULC listing

DN-60977:D • 8/13/2020 — Page 1 of 3

FSP-951-IV: Ivory, low-profile intelligent photoelectric sensor B200SCOA-IV: Ivory Intelligent, programmable sounder base in
English/French (required in Canada for ULC applications with CO
FSP-951A-IV: Same as FSP-951-IV but with ULC listing
Series detector applications, ULC listing
FSP-951T: White, same as FSP-951 but includes a built-in 135°F B200S-LF-WH: White, Low Frequency Intelligent, programmable
(57°C) fixed-temperature thermal device, FlashScan only sounder base. Produces a fundamental frequency of 520 Hz +/-
FSP-951TA: Same as FSP-951T but with ULC listing 10% with a square wave or its equivalent; designed to meet the
NFPA 72 sleeping space requirement. (CSFM: 7300-1653:0238)
FSP-951T-IV: Ivory, same as FSP-951T but includes a built-in 135°F
(57°C) fixed-temperature thermal device B200S-LF-IV: Ivory, Low Frequency Intelligent, programmable
sounder base. Produces a fundamental frequency of 520 Hz +/-
FSP-951TA-IV: Same as FSP-951T-IV but with ULC listing 10% with a square wave or its equivalent; designed to meet the
FSP-951R: White, low-profile intelligent photoelectric sensor, NFPA 72 sleeping space requirement. (CSFM: 7300-1653:0238)
remote test capable, for use with DNR/DNRW, FlashScan only B200SR-WH: White, Intelligent sounder base capable of producing
FSP-951RA: Same as FSP-951R but with ULC listing, for use with sound output with ANSI Temporal 3 or continuous tone. Intended for
DNRA retrofit applications. (CSFM: 7300-1653:0213)
B200SR-IV: Ivory, Intelligent sounder base capable of producing
FSP-951R-IV: Ivory, low-profile intelligent photoelectric sensor,
sound output with ANSI Temporal 3 or continuous tone. Intended for
remote test capable, for use with DNR/DNRW
retrofit applications. (CSFM: 7300-1653:0213)
FSP-951RA-IV: Same as FSP-951R-IV but with ULC listing, for use B200SRA-WH: Same as B200SR-WH with, ULC listing
with DNRA
B200SRA-IV: Same as B200SR-IV in Ivory color, ULC listing
INTELLIGENT BASES
B200SR-LF-WH: White, Low Frequency Intelligent, programmable
NOTE: For details on intelligent bases, see DN-60981. sounder base. Produces a fundamental frequency of 520 Hz +/-
B300-6: White, 6” base, standard flanged low-profile mounting base 10% with a square wave or its equivalent; designed to meet the
(CSFM: 7300-1653:0109) NFPA 72 sleeping space requirement. Intended for retrofit applica-
tions. (CSFM: 7300-1653:0238)
B300-6-IV: Ivory,6” base, standard flanged low-profile mounting
base (CSFM: 7300-1653:0109) B200SR-LF-IV: Ivory, Low Frequency Intelligent, programmable
sounder base. Produces a fundamental frequency of 520 Hz +/-
B300A-6: Same as B300-6, ULC listed
10% with a square wave or its equivalent; designed to meet the
B300A-6-IV: Ivory, 6” standard flanged low-profile mounting base, NFPA 72 sleeping space requirement. Intended for retrofit applica-
ULC listed tions. (CSFM: 7300-1653:0238)
B300-6-BP: Bulk pack of B300-6, package contains 10 MOUNTING KITS AND ACCESSORIES
B501-WHITE: White, 4” standard European flangeless mounting TR300: White, replacement flange for B210LP(A) base
base. UL/ULC listed (CSFM: 7300-1653:0109)
TR300-IV: Ivory, replacement flange for B210LP(A) base
B501-BL: Black, 4” standard European flangeless mounting base.
UL/ULC listed (CSFM: 7300-1653:0109) RA100Z(A): Remote LED annunciator. 3-32 VDC. Mounts to a U.S.
single-gang electrical box. For use with B501(A) and B300-6(A).
B501-IV: Ivory color, 4” standard European flangeless mounting
base. UL/ULC listed (CSFM: 7300-1653:0109) M02-04-00: Test magnet
B501-WHITE-BP: Bulk pack of B501-WHITE contains 10 M02-09-00: Test magnet with telescoping handle
B224RB-WH: White, relay base (CSFM: 7300-1653:0216) CK300: Color Kit (includes cover and trim ring), white, 10-pack

B224RB-IV: Ivory, relay base (CSFM: 7300-1653:0216) CK300-IV: Color Kit (includes cover and trim ring), ivory, 10-pack

B224RBA-WH: White, relay base, ULC listing CK300-BL: Color Kit (includes cover and trim ring), black, 10-pack

B224RBA-IV: Ivory, relay base, ULC listing

B224BI-WH: White, isolator detector base (CSFM: 7300-1653:0216)
B224BI-IV: Ivory isolator detector base (CSFM: 7300-1653:0216)
B224BIA-WH: White, isolator detector base, ULC listing
B224BIA-IV: Ivory isolator detector base, ULC listing
B200S-WH: White, Intelligent addressable sounder base capable of
producing sound output in high or low volume with ANSI Temporal 3,
ANSI Temporal 4, continuous tone, marching tone, and custom tone.
Uses FlashScan protocol. (CSFM: 7300-1653:0213)
B200S-IV: Ivory, Intelligent addressable sounder base capable of
producing sound output in high or low volume with ANSI Temporal 3,
ANSI Temporal 4, continuous tone, marching tone, and custom tone.
Uses FlashScan protocol. (CSFM: 7300-1653:0213)
B200SA-WH: Same as B200S-WH, ULC listing
B200SA-IV: Same as B200S-IV, ULC listing
B200SCOA-WH: White, Intelligent, programmable sounder base in
English/French (required in Canada for ULC applications with CO
Series detector applications

Page 2 of 3 — DN-60977:D • 8/13/2020

SPECIFICATIONS

Sensitivity: Listings and Approvals

• UL Applications: 0.5% to 4.0% per foot obscuration. Listings and approvals below apply to the FSP-951 Series detectors.
• ULC Applications: 0.5% to 3.5% per foot obscuration In some cases, certain modules may not be listed by certain
Size: 2.0" (51mm) high; base determines diameter approval agencies, or listing may be in process. Consult factory for
latest listing status.
– B300-6 series: 6.1" (15.6 cm) diameter
• UL/ULC Listing: S1115
– B501 series: 4" (10.2 cm) diameter
• FM Approved
For a complete list of detector bases see DN-60981
• CSFM: 7272-0028:0503
Shipping weight: 3.4 oz. (95 g)
Operating temperature range:
• FSP-951 Series: 32°F to 122°F (0°C to 50°C)
• FSP-951T Series: 32°F to 100°F(0°C to 38°C)
• FSP-951R Series installed in DNR/DNRA/DNRW, -4°F to 158°F
(-20°C to 70°C)
UL/ULC Listed Velocity Range: 0-4000 ft/min. (1219.2 m/min.),
suitable for installation in ducts
Relative humidity: 10% – 93% non-condensing
Thermal ratings: fixed-temperature set point 135°F (57°C), rate-of-
rise detection 15°F (8.3°C) per minute, high temperature heat 190°F
(88°C)
ELECTRICAL SPECIFICATIONS
Voltage range: 15 - 32 volts DC peak
Standby current (max. avg.): 200µA @ 24 VDC (one communica-
tion every 5 seconds with LED enabled)
Max current: 4.5 mA @ 24 VDC (“ON”)
DETECTOR SPACING AND APPLICATIONS
NOTIFIER recommends spacing detectors in compliance with NFPA
72. In low airflow applications with smooth ceiling, space detectors
30 feet (9.1m). For specific information regarding detector spacing,
placement, and special applications refer to NFPA 72. A System
Smoke Detector Application Guide, document SPAG91, is available
at www.systemsensor.com.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
NOTIFIER FlashScan®, NOTIFIER®, and System Sensor® are registered trade-
12 Clintonville Road marks of Honeywell International, Inc.
Northford, CT 06472 ©2020 by Honeywell International Inc. All rights reserved. Unauthorized
203.484.7161 use of this document is strictly prohibited.

www.notifier.com Country of Origin: Mexico