Au Optronics Corporation: Product Specification

Download as pdf or txt
Download as pdf or txt
You are on page 1of 37

B154EW01 VC Rev A00

Product Specification

AU OPTRONICS CORPORATION

Product Specification

15.4” WXGA Color TFT-LCD Module

Model Name: B154EW01 VC Rev A00


Dell P/N: FF059
Inverter: Foxconn + Maximum 6.0

Approved by Prepared by

www.DataSheet.co.kr

MDBU Marketing Division / AU Optronics corporation

Customer Checked & Approved by

Document version 0.2 1/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

Product Specification

15.4” WXGA Color TFT-LCD Module


Model Name: B154EW01
V.C Rev A00
Dell P/N : FF059
Inverter: Foxconn + Maximum 6.0

( ) Preliminary Specifications
(V ) Final Specifications
www.DataSheet.co.kr

Note: This Specification is subject to change without notice.

Document version 0.2 2/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

Contents
1. Handling Precautions .........................................................................................5
2. General Description ............................................................................................5
2.1 Display Characteristics ..................................................................................................... 6
2.2 Optical Characteristics...................................................................................................... 7
3. Functional Block Diagram................................................................................12
4. Absolute Maximum Ratings .............................................................................13
4.1 TFT LCD Module ............................................................................................................ 13
4.2 Backlight Unit.................................................................................................................. 13
4.3 Absolute Ratings of Environment.................................................................................... 13
5. Electrical characteristics..................................................................................14
5.1 TFT LCD Module ............................................................................................................ 14
5.2 Backlight Unit.................................................................................................................. 16
6. Signal Characteristic ........................................................................................19
6.1 Pixel Format Image......................................................................................................... 19
6.2 The input data format...................................................................................................... 20
6.3 Signal Description........................................................................................................... 21
6.4 Interface Timing .............................................................................................................. 23
www.DataSheet.co.kr

6.5 Power ON/OFF Sequence .............................................................................................. 25


7. Connector & Pin Assignment ..........................................................................26
7.1 TFT LCD Module ............................................................................................................ 26
7.2 Backlight Unit.................................................................................................................. 26
7.3 Signal for Lamp connector.............................................................................................. 26
8. Vibration and Shock Test .................................................................................27
8.1 Vibration Test .................................................................................................................. 27
8.2 Shock Test Spec: ............................................................................................................ 27
9. Reliability ...........................................................................................................28
10. Mechanical Characteristics............................................................................29
10.1 LCM Outline Dimension................................................................................................ 29
10.2 Screw Hole Depth and Center Position ........................................................................ 30
11. Shipping and Package....................................................................................31
11.1 Shipping Label Format .................................................................................................. 31
11.2. Carton package............................................................................................................ 32
11.3 Shipping package of palletizing sequence .................................................................... 32
12. Appendix: EDID description...........................................................................33

Document version 0.2 3/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

Record of Revision

Version and Date Page Old description New Description Remark


0.1 2005/08/01 All First Edition for Customer

0.2 2005/08/15 18 Update Inverter Characteristic Spec.

0.3 2006/01/09 33 Update EDID description

www.DataSheet.co.kr

Document version 0.2 4/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

1. Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
www.DataSheet.co.kr

11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source(,
IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
2. General Description
B154EW01 V8 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and backlight system. The screen format is intended to support the WXGA (1280(H)
x 800(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface
compatible. Inverter of backlight is not included.

Document version 0.2 5/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

B154EW01 VC is designed for a display unit of notebook style personal computer and industrial
machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:

Items Unit Specifications


Screen Diagonal [mm] 391 (15.4W”)
Active Area [mm] 331.2 X 207.0

Pixels H x V 1280x3(RGB) x 800

Pixel Pitch [mm] 0.2588X0.2588

Pixel Arrangement R.G.B. Vertical Stripe

Display Mode Normally White

White Luminance (ICCFL=6.0mA) [cd/m2] 160 typ. (5 points average)


Note: ICCFL is lamp current 150 min. (5 points average)
(Note1)
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 400 typ
www.DataSheet.co.kr

Optical Rise Time/Fall Time [msec] 4/12 typ.


Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 6.5 max.(without inverter)
Weight(w/o Inverter) [Grams] 585 max.
Physical Size [mm] 344.0 typ. x 222.0 typ. x 6.5 max.

Electrical Interface 1 channel LVDS


Surface Treatment Glare, Hardness 3H,
,Reflectance 4.3%
Support Color 262K colors ( RGB 6-bit )

Temperature Range
Operating [oC] 0 to +50
Storage (Non-Operating) [oC] -20 to +60
RoHS Compliance RoHS Compliance

Document version 0.2 6/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

2.2 Optical Characteristics


The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):

Item Unit Conditions Min. Typ. Max. Note


White Luminance [cd/m2] 5 points average 150 160 - 1, 4, 5.
ICCFL=6.0mA
Viewing Angle [degree] Horizontal (Right) - 40 - 9
[degree] CR = 10 (Left) - 40 -
[degree] Vertical (Upper) - 10 -
[degree] CR = 10 (Lower) - 30 -
Luminance Uniformity 5 Points 1.25 1
Luminance Uniformity 13 Points 1.50 2
CR: Contrast Ratio 300 400 - 6
Cross talk % 4 7
Response Time [msec] Rising - 4 8 8
[msec] Falling - 12 17
[msec] Rising + Falling 16 25
Color / Chromaticity Red x 0.570 0.600 0.630 2,8
Coordinates Red y 0.300 0.340 0.370
(CIE 1931) Green x 0.280 0.310 0.340
Green y 0.530 0.560 0.590
Blue x www.DataSheet.co.kr
0.120 0.150 0.180
Blue y 0.085 0.115 0.145
White x 0.290 0.313 0.343
White y 0.299 0.329 0.350

Document version 0.2 7/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

Note 1: 5 points position (Display area : 331.2mm x 207.0mm)

W
W /4 W /4 W /4 W /4

H /4

1 2
H /4

H 3

H /4

4 5

H /4

Note 2: 13 points position

W /4 W /4 W /4 W /4
10 10

10
1 2 3
www.DataSheet.co.kr

H /4

4 5

H /4

H 6 7 8

H /4

9 10

H /4 11 12 13
10

Note 3: The luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the
minimum test point luminance

Maximum Brightness of five points


δW5 =
Minimum Brightness of five points

Maximum Brightness of thirteen points


δW13 =
Minimum Brightness of thirteen points

Document version 0.2 8/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

Note 4: Measurement method


The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room.

Photo detector
(BM-5A BM-7 or

Field=

50 cm

LCD Panel TFT-LCD Module

www.DataSheet.co.kr

Center
Note 5: Definition of Average Luminance of of the screen
White (YL):

Measure the luminance of gray level 63 at 5 points,YL = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L (x) is corresponding to the luminance of the point X at Figure in Note (1).

Note 6: Definition of contrast ratio:


Contrast ratio is calculated with the following formula.

Brightness on the “White” state


Contrast ratio (CR)=
Brightness on the “Black” state

Note 7: Definition of Cross Talk (CT)


CT = | YB – YA | / YA × 100 (%)

Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)

YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Document version 0.2 9/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

Note 8: Definition of response time:

The output signals of BM-7 or equivalent are measured when the input signals are changed
from “Black” to “White” (falling time) and from “White” to “Black” (rising time), respectively. The
response time interval between the 10% and 90% of amplitudes. Refer to figure as below.

"Black"
"White" "White"
100%
Signal(Relative value)

90%

10% www.DataSheet.co.kr

0%
Tr Tf

Document version 0.2 10/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

Note 9. Definition of viewing angle


Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the
screen rotated about its center to develop the desired measurement viewing angle.

www.DataSheet.co.kr

Document version 0.2 11/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

3. Functional Block Diagram


The following diagram shows the functional block of the 15.4 inches wide Color TFT/LCD Module:

X-Driver

(4 pairs LVDS) LCD DRIVE


BOARD
RxIN0
RxIN1 LCD
RxIN2 Controller TFT ARRAY/CELL
RxCLKIN 1280(R/G/B) x 3 x 800
DC-DC
Converter
Ref circuit
Backlight Unit
Y-Driver
VDD
GND
LCD Connector(30pin) www.DataSheet.co.kr
Lamp Connector(2pin)
JAE FI-XB30SL-HF10 JST BHSR-02VS-1
Mating Housing JAE FI-X30H Mating Type SM02B-BHSS-1-TB

Document version 0.2 12/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

4. Absolute Maximum Ratings


Absolute maximum ratings of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
Logic/LCD Drive Voltage Vin -0.3 +4.0 [Volt] Note 1,2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min Max Unit Conditions
CCFL Current ICCFL - 6.5 [mA] rms Note 1,2
4.3 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
o
Operating Temperature TOP 0 +50 [ C] Note 3
Operation Humidity HOP 5 95 [%RH] Note 3
o
Storage Temperature TST -20 +60 [ C] Note 3
Storage Humidity HST 5 95 [%RH] Note 3

Note 1: At Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS(Incoming Inspection Standard).

Twb=39° C
www.DataSheet.co.kr

Operating Range Storage Range

Document version 0.2 13/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;

Symble Parameter Min Typ Max Units Note


VDD Logic/LCD Drive 3.0 3.3 3.6 [Volt]
Voltage
PDD VDD Power 2 [Watt] Note 1
IDD IDD Current 500 600 [mA] Note 1
IRush Inrush Current 2000 [mA] Note 2
VDDrp Allowable 100 [mV]
Logic/LCD Drive p-p
Ripple Voltage

Note 1 : Maximum Measurement Condition:Black Patterm

Note 2:Measure Condition


+5.0V Q3
AO6402
D6 F1
D5
D2 S
VCC
D1

R1 (LCD Module Input)


47K
G

www.DataSheet.co.kr

C1
1uF/16V
(High to Low)
D2
D1

D5
D6

Control
Signal R2
Q3
AO6402
G

1K
S

C3
2

+12.0V
SW1
SW MAG-SPST VR1 0.01uF/25V
1

47K

C2
1uF/25V

90% 3.3V

10%
0V
0.5ms

Vin rising time

Document version 0.2 14/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

5.1.2 Signal Electrical Characteristics


Input signals shall be low or High-impedance state when VDD is off.
It is recommended to refer the specifications of THC63LVDF84A(Thine Electronics Inc.) in
detail.

Signal electrical characteristics are as follows;

Parameter Condition Min Max Unit


Differential Input High
Vth Threshold (Vcm=+1.2V) 100 [mV]

Differential Input Low


Vtl Threshold (Vcm=+1.2V) -100 [mV]

Differential Input
Vcm 1.125 1.375 [V]
Common Mode Voltage

Note: LVDS Signal Waveform


www.DataSheet.co.kr

Vth

Vtl

Vcm

VSS

Document version 0.2 15/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

5.2 Backlight Unit


Parameter guideline for CCFL Inverter

Parameter Min Typ Max Units Condition


White Luminance
5 points average - 160 - [cd/m2 ] (Ta=25℃)
CCFL current(ICCFL) 3.0 6.0 6.5 [mA] rms (Ta=25℃)
Note 2
CCFL Frequency(FCCFL) 50 62 70 [KHz] (Ta=25℃)
Note 3,4

CCFL Ignition Voltage(Vs) 1430 [Volt] rms (Ta= 0℃)


Note 5
CCFL Ignition Voltage(Vs) 1190 [Volt] rms (Ta= 25℃)
Note 5
CCFL Voltage (Reference) 648 720 792 [Volt] rms (Ta=25℃)
(VCCFL) Note 6

CCFL Power consumption - 4.30 4.50 [Watt] (Ta=25℃)


(PCCFL) Note 6

Note 1: Typ are AUO recommended Design Points. www.DataSheet.co.kr

*1 All of characteristics listed are measured under the condition using the AUO Test inverter.
*2 In case of using an inverter other than listed, it is recommended to check the inverter carefully. Sometimes,
interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may
happen.
*3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of CCFL, for
instance, becomes more than 1 [M ohm] when CFL is damaged.
*4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is recommended to keep
on applying kick-off voltage for 1 [Sec] until discharge.
*5 CCFL discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the
screen.
*6 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL discharge
frequency. So all the parameters of an inverter should be carefully designed so as not to produce too much
leakage current from high-voltage output of the inverter.
Note 2: It should be employed the inverter which has “Duty Dimming”, if ICCFL is less than 4mA.
Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter and TFT
LCD.
Note 4: The frequency range will not affect to lamp life and reliability characteristics.

Document version 0.2 16/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,430 voltage.
Lamp units need 1,400 voltage minimum for ignition.
Note 6: Calculator value for reference (ICCFL×VCCFL=PCCFL)
Note 7: Requirements for a system inverter design, which is intended to have a better display performance, a better
power efficiency and a more reliable lamp, are following.
It shall help increase the lamp lifetime and reduce leakage current.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion rate of the waveform should bewithin √2 ±10%.
* Inverter output waveform had better be more similar to ideal sine wave.

www.DataSheet.co.kr

Document version 0.2 17/37

Datasheet pdf - http://www.DataSheet4U.net/


B154EW01 VC Rev A00

Product Specification

5.3 Inverter Characteristic

Electrical Characteristics : Vin= 7.5V~21V, Ta=25℃


Condition
No. Item Symbol Min. Typ. Max. Unit
1 Input Voltage INV_SRC - 7.5 14.0 21.0 V

2 Input Voltage 5VALW - 4.85 - 5.20 V

3 Input Current Iin Vin=14.0V, max. output - 0.420 - A

4 Input Power Pin Vin=14.0V, Iout=6.5mA - - 6.20 W

5 Backlight ON Enable the inverter 2.0 - 5.25 V

ON/OFF Control(1) OFF Disable the inverter -0.3 - 0.8 V

6 SMBus Mode Min. output: 00H 00 - FF Hex.


Brightness Adjust SMB_DAT Max. output: FFH

PWM(Hz) - - 10 - KHz

DPST mode PWM - 3.135 3.30 3.465 V


7 (System side PWM Voltage
input)
Signal - 00 - FF Hex
intensity www.DataSheet.co.kr

8 Output Voltage Vout Max. output - 700 - Vrms

Iout (Min) 1.2 1.5 1.8 mArms


9 Output Current Ta=25℃, after running 30 min.
Iout (Max) 6.3 6.5 6.8 mArms

10 Frequency Freq Max. output 45 55 65 KHz

11 Output Power Pout Vin=14.0V, Iout(Max) - 4.96 - W

12 Burst Mode Frequency fB - 200 - Hz

13 Ambient Light input 5 - 1000 Lux


signal

14 Open Lamp Voltage(2) Vopen No Load 1400 - - Vrms

15 Striking Time Ts No Load 0.6 1.0 1.4 Sec

16 Efficiency η Vin=7.5V, Max. output, - 80 - %


Load=100K

17 Start –up time - - 0.1 Sec

Document version 0.2 18/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.

0 1 1278 1279

1st Line R GB R GB R G B R GB

800th Line R GB R GB R G B R GB

www.DataSheet.co.kr

Document version 0.2 19/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

6.2 The input data format

Signal Name Description


R5 Red Data 5 (MSB) Red-pixel Data
R4 Red Data 4 Each red pixel's brightness data consists of
R3 Red Data 3 these 6 bits pixel data.
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0 (LSB)

Red-pixel Data
G5 Green Data 5 (MSB) Green-pixel Data
G4 Green Data 4 Each green pixel's brightness data consists of
G3 Green Data 3 these 6 bits pixel data.
www.DataSheet.co.kr

G2 Green Data 2
G1 Green Data 1
G0 Green Data 0 (LSB)

Green-pixel Data
B5 Blue Data 5 (MSB) Blue-pixel Data
B4 Blue Data 4 Each blue pixel's brightness data consists of
B3 Blue Data 3 these 6 bits pixel data.
B2 Blue Data 2
B1 Blue Data 1
B0 Blue Data 0 (LSB)

Blue-pixel Data
RxCLKIN Data Clock The typical frequency is 68.9 MHZ.. The signal
is used to strobe the pixel data and DE signals.
All pixel data shall be valid at the falling edge
when the DE signal is high.
DE Display Timing This signal is strobed at the falling edge of
RxCLKIN. When the signal is high, the pixel data
shall be valid to be displayed.
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync The signal is synchronized to RxCLKIN .
Note: Output signals from any system shall be low or High-impedance state when VDD is off.

Document version 0.2 20/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

6.3 Signal Description/Pin Assignment


LVDS is a differential signal technology for LCD interface and high speed data transfer device.
PIN# Signal Name Description
1 GND Ground
2 VDD +3.3V Power Supply
3 VDD +3.3V Power Supply
4 VEDID +3.3V EDID Power
5 NC No Connection (Reserve for AUO test)
6 CLKEDID EDID Clock Input
7 DATAEDID EDID Data Input
8 RxIN0- LVDS differential data input(R0-R5, G0)
9 RxIN0+ LVDS differential data input(R0-R5, G0)
10 GND Ground
11 RxIN1- LVDS differential data input(G1-G5, B0-B1)
12 RxIN1+ LVDS differential data input(G1-G5, B0-B1)
13 GND Ground
14 RxIN2- LVDS differential data input(B2-B5, HS, VS, DE)
15 RxIN2+ LVDS differential data input(B2-B5, HS, VS, DE)
16 GND Ground
17 RxCLKIN- LVDS differential clock input
www.DataSheet.co.kr

18 RxCLKIN+ LVDS differential clock input


19 GND Ground
20 GND Ground
21 NC No Connection (Reserve for AUO test)
22 NC No Connection (Reserve for AUO test)
23 NC No Connection (Reserve for AUO test)
24 NC No Connection (Reserve for AUO test)
25 NC No Connection (Reserve for AUO test)
26 NC No Connection (Reserve for AUO test)
27 NC No Connection (Reserve for AUO test)
28 NC No Connection (Reserve for AUO test)
29 NC No Connection (Reserve for AUO test)
30 NC No Connection (Reserve for AUO test)

Document version 0.2 21/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification
Note1: Start from right side

Connector

1
30
NC

GND

Note2: Input signals shall be low or High-impedance state when VDD is off.
internal circuit of LVDS inputs are as following.
The module uses a 100ohm resistor between positive and negative data lines of each receiver input
www.DataSheet.co.kr

Signal Input
LVDS Receiver
Pin No.

8 RxIN0-

9 RxIN0+

11 RxIN1-

12 RxIN1+

14 RxIN2-

15 RxIN2+

17 RxCLKIN-

18 RxCLKIN+

Document version 0.2 22/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

6.4 Interface Timing


6.4.1 Timing Characteristics
Basically, interface timings should match the 1280x800 /60Hz manufacturing guide line timing.

Parameter Symbol Min. Typ. Max. Unit


Frame Rate - 50 60 - Hz
Clock frequency 1/ TClock 50 68.9 80 MHz
Period TV 803 816 832
Vertical
Active TVD 800 800 800 TLine
Section
Blanking TVB 3 16 32
Period TH 1302 1408 1700
Horizontal
Active THD - 1280 - TClock
Section
Blanking THB 22 128 420

Note : DE mode only

www.DataSheet.co.kr

Document version 0.2 23/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

6.4.2 Timing diagram

TCLOCK Input Timing Definition ( DE Mode)

DOTCLK

Input Invaild Pixel Pixel Pixel Pixel Pixel Invaild Pixel


Data Data 1 2 3 N-1 N Data 1

DE
THB THD

TH

DE
TVB
TVD

TV

www.DataSheet.co.kr

Document version 0.2 24/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification
6.5 Power ON/OFF Sequence

VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart.
Signals from any system shall be Hi-Z state or low level when VDD is off.

T1
90% 90%

10% 10%
Power Supply VDD
T2 T3 T7 T4

LVDS Interface VALID


T5 DATA

T6

Backlight On

Power Sequence Timing


www.DataSheet.co.kr

Value
Parameter Min. Typ. Max. Units
T1 0.5 - 10 (ms)
T2 0 - 50 (ms)
T3 0 - 50 (ms)
T4 400 - - (ms)
T5 200 - - (ms)
T6 200 - - (ms)
T7 0 - 10 (ms)

Document version 0.2 25/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

7. Connector Description

Physical interface is described as for the connector on module.


These connectors are capable of accommodating the following signals and will be following
components.

7.1 TFT LCD Module

Connector Name / Designation For Signal Connector


Manufacturer JAE or compatible
Type / Part Number FI-XB30SL-HF10 or compatible
Mating Housing/Part Number FI-X30H or compatible

7.2 Backlight Unit


Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.

www.DataSheet.co.kr

Connector Name / Designation For Lamp Connector


Manufacturer JST
Type / Part Number BHSR-02VS-1
Mating Type / Part Number SM02B-BHSS-1-TB

7.3 Signal for Lamp connector

Pin # Cable color Signal Name

1 Red Lamp High Voltage

2
White Lamp Low Voltage

Document version 0.2 26/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

8. Vibration and Shock Test (Stand alone)

8.1 Vibration Test


Test Spec:
Test method: Non-Operation
Acceleration: 1.3G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)

8.2 Shock Test Spec:


Test Spec:
Test method: Non-Operation
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse: X,Y,Z .one time for each side

www.DataSheet.co.kr

Document version 0.2 27/37


Datasheet pdf - http://www.DataSheet4U.net/
B154EW01 VC Rev A00

Product Specification

9. Reliability

Items Required Condition Note


Temperature
40℃/95%,250Hr
Humidity Bias
High Temperature
65℃/Dry,250Hr
Operation
Low Temperature
0℃,300Hr
Operation
On/Off Test 25℃,150hrs(ON/10 sec. OFF/10sec., 10,000 cycles)
Hot Storage 65℃/20% RH ,250 hours
Cold Storage -40℃/50% RH ,250 hours
Thermal Shock Test -40℃/30 min ,65℃/30 min 100cycles
Hot Start Test 50℃/1 Hr min. power on/off per 5 minutes, 5 times
Cold Start Test 0℃/1 Hr min. power on/off per 5 minutes, 5 times
Shock Test
220G, 2ms, Half-sine wave
(Non-Operating)

Vibration Test Random vibration, 1.3 G zero-to-peak, 10 to 500 Hz, 30


(Non-Operating) mins in each of three mutually perpendicular axes.

Contact : ±8KV/ operation Note 1


ESD
Air : ±15KV / operation
www.DataSheet.co.kr

Room temperature
25℃, 2000hours, Operating with loop pattern
Test

Note1: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Note2: CCFL Life time: 10,000 hours minimum under normal module usage.
Note3: MTBF (Excluding the CCFL): 30,000 hours with a confidence level 90%

Document version 0.2 28/37


Datasheet pdf - http://www.DataSheet4U.net/
10. Mechanical Characteristics
10.1 LCM Outline Dimension

www.DataSheet.co.kr

Document version 0.1 29/37


Datasheet pdf - http://www.DataSheet4U.net/
10.2 Screw Hole Depth and Center Position
Screw hole minimum depth, from side surface =2.5 mm (See drawing)

Screw hole center location, from front surface = 3.7 ± 0.2mm (See drawing)
Screw Torque: Maximum 2.5 kgf-cm

www.DataSheet.co.kr

Document version 0.1 30/37

Datasheet pdf - http://www.DataSheet4U.net/


11. Shipping and Package

Model name Week code


11.1 Shipping Label Format

Note 1

Rev X 00 = TS/WS level panels


Dell P/N: FF059
Rev X 1x = ES level panels with x = 0,1, 2, 3 depending on ES
steps
Rev X 2x = CS level panels with x = 0,1, 2, 3 depending on CS
steps
Rev A 00 = RTS level panels

Note 1:

IC Combination Control Code H/W


www.DataSheet.co.kr

Source NT 39360 0AXXG 0A


Gate IC: NT 3959C

Document version 0.1 31/37

Datasheet pdf - http://www.DataSheet4U.net/


11.2. Carton package

The outside dimension of carton is 455 (L)mm x 380 (W)mm x 355 (H)mm

www.DataSheet.co.kr

11.3 Shipping package of palletizing sequence

Top cardboard

Bottom cardboard PE band


Wooden pallet Corner angle Stretch film

Note : Limit of box palletizing = Max 3 layers(ship and stock conditions)

Document version 0.1 32/37

Datasheet pdf - http://www.DataSheet4U.net/


12. Appendix: EDID description
B154EW01 VC(Foxconn) EDID Table
Byte Value Value Value
Field Name and Comments
(hex) (Hex) (Binary) (DEC)
0 Header 00 00000000 0
1 Header FF 11111111 255
2 Header FF 11111111 255
Header

3 Header FF 11111111 255


4 Header FF 11111111 255
5 Header FF 11111111 255
6 Header FF 11111111 255
7 Header 00 00000000 0
EISA manufacture code = 3 Character
8 ID 06 00000110 6
EISA manufacture code (Compressed
9 ASCII) AF 10101111 175
Panel Supplier Reserved – Product
0A Code 74 01110100 116
Panel Supplier Reserved – Product
Vendor / Product

0B Code 1C 00011100 28
EDID Version

LCD module Serial No - Preferred but


0C Optional (“0” if not used) 00 00000000 0
LCD module Serial No - Preferred but
0D Optional (“0” if not used) 00 00000000 0
LCD module Serial No - Preferred but
www.DataSheet.co.kr

0E Optional (“0” if not used) 00 00000000 0


LCD module Serial No - Preferred but
0F Optional (“0” if not used) 00 00000000 0
10 Week of manufacture 01 00000001 1
11 Year of manufacture 0F 00001111 15
12 EDID structure version # = 1 01 00000001 1
13 EDID revision # = 3 03 00000011 3
14 Video I/P definition = Digital I/P (80h) 80 10000000 128
15 Max H image size = (Rounded to cm) 21 00100001 33
Parameters
Display

16 Max V image size = (Rounded to cm) 15 00010101 21


Display gamma = (gamma ×100)-100
17 = Example: ( 2.2×100 ) – 100 = 120 78 01111000 120
Feature support ( no DPMS, Active off,
18 RGB, timing BLK 1) 0A 00001010 10
19 Red/Green Low bit (RxRy/GxGy) A7 10100111 167
1A Blue/White Low bit (BxBy/WxWy) E5 11100101 229
1B Red X 99 10011001 153
Coordinates
Panel Color

1C Red Y 59 01011001 89
1D Green X 4F 01001111 79
1E Green Y 8C 10001100 140
1F Blue X 27 00100111 39
20 Blue Y 1D 00011101 29
21 White X 50 01010000 80
Document version 0.1 33/37

Datasheet pdf - http://www.DataSheet4U.net/


22 White Y 54 01010100 84
Established Established timings 1 (00h if not
Timings 23 used) 00 00000000 0
Established timings 2 (00h if not
24 used) 00 00000000 0
Manufacturer’s timings (00h if not
25 used) 00 00000000 0
26 Standard timing ID1 (01h if not used) 01 00000001 1
27 Standard timing ID1 (01h if not used) 01 00000001 1
28 Standard timing ID2 (01h if not used) 01 00000001 1
29 Standard timing ID2 (01h if not used) 01 00000001 1
2A Standard timing ID3 (01h if not used) 01 00000001 1
Standard Timing ID

2B Standard timing ID3 (01h if not used) 01 00000001 1


2C Standard timing ID4 (01h if not used) 01 00000001 1
2D Standard timing ID4 (01h if not used) 01 00000001 1
2E Standard timing ID5 (01h if not used) 01 00000001 1
2F Standard timing ID5 (01h if not used) 01 00000001 1
30 Standard timing ID6 (01h if not used) 01 00000001 1
31 Standard timing ID6 (01h if not used) 01 00000001 1
32 Standard timing ID7 (01h if not used) 01 00000001 1
33 Standard timing ID7 (01h if not used) 01 00000001 1
34 Standard timing ID8 (01h if not used) 01 00000001 1
35 Standard timing ID8 (01h if not used) 01 00000001 1
Pixel Clock/10,000
36 (LSB) C7 11000111 199
Pixel Clock/10,000 www.DataSheet.co.kr

37 (MSB) 1B 00011011 27
Horizontal Active
38 (lower 8 bits) 00 00000000 0
Horizontal Blanking (Thbp)
39 (lower 8 bits) A0 10100000 160
Horizontal Active/Horizontal blanking
3A (Thbp) (upper4:4 bits) 50 01010000 80
Timing Descripter #1

3B Vertical Active 20 00100000 32


Vertical Blanking (Tvbp) (DE
3C Blanking typ. for DE only panels) 17 00010111 23
Vertical Active : Vertical Blanking
3D (Tvbp) (upper4:4 bits) 30 00110000 48
3E Horizontal Sync, Offset (Thfp) 15 00010101 21
3F Horizontal Sync, Pulse Width 20 00100000 32
Vertical Sync, Offset (Tvfp) Sync
40 Width 44 01000100 68
Horizontal Vertical Sync Offset/Width
41 upper 2 bits 00 00000000 0
42 Horizontal Image Size 4B 01001011 75
43 Vertical image Size CF 11001111 207
Horizontal Image Size / Vertical image
44 size 10 00010000 16
Horizontal Border = 0 (Zero for
45 Notebook LCD) 00 00000000 0
Document version 0.1 34/37

Datasheet pdf - http://www.DataSheet4U.net/


Vertical Border = 0 (Zero for
46 Notebook LCD) 00 00000000 0
Non-interlaced, Normal, no stereo,
Separate sync, H/V pol Negatives, DE
only note: LSB is set to “1” if panel
is DE-timing only. H/V can be
47 ignored. 18 00011000 24
Pixel Clock/10,000
48 (LSB) 26 00100110 38
Pixel Clock/10,000
49 (MSB) 17 00010111 23
Horizontal Active = xxxx pixels
4A (lower 8 bits) 00 00000000 0
Horizontal Blanking (Thbp) = xxxx
4B pixels (lower 8 bits) A0 10100000 160
Horizontal Active/Horizontal blanking
4C (Thbp) (upper4:4 bits) 50 01010000 80
4D Vertical Active = xxxx lines 20 00100000 32
Vertical Blanking (Tvbp) = xxxx lines
4E (DE Blanking typ. for DE only panels) 17 00010111 23
Timing Descripter #2

Vertical Active : Vertical Blanking


4F (Tvbp) (upper4:4 bits) 30 00110000 48
Horizontal Sync, Offset (Thfp) = xxxx
50 pixels 15 00010101 21
Horizontal Sync, Pulse Width = xxxx
51 pixels 20 00100000 32
Vertical Sync, Offset (Tvfp) = xx lines
52 Sync Width = xx lines www.DataSheet.co.kr
44 01000100 68
Horizontal Vertical Sync Offset/Width
53 upper 2 bits 00 00000000 0
54 Horizontal Image Size =xxx mm 4B 01001011 75
55 Vertical image Size = xxx mm CF 11001111 207
Horizontal Image Size / Vertical image
56 size 10 00010000 16
Horizontal Border = 0 (Zero for
57 Notebook LCD) 00 00000000 0
Vertical Border = 0 (Zero for
58 Notebook LCD) 00 00000000 0
Module “A” Revision =
59 Example: 00, 01, 02, 03, etc. 00 00000000 0
5A Flag 00 00000000 0
5B Flag 00 00000000 0
Dell specific information
Timing Descripter #3

5C Flag 00 00000000 0
5D Dummy Descriptor FE 11111110 254
5E Flag 00 00000000 0
5F Dell P/N 1st Character 46 01000110 70
60 Dell P/N 2nd Character 46 01000110 70
61 Dell P/N 3rd Character 30 00110000 48
62 Dell P/N 4th Character 35 00110101 53
63 Dell P/N 5th Character 39 00111001 57
64 LCD Supplier EEDID Revision # 00 00000000 0

Document version 0.1 35/37

Datasheet pdf - http://www.DataSheet4U.net/


65 Manufacturer P/N 42 01000010 66
66 Manufacturer P/N 31 00110001 49
67 Manufacturer P/N 35 00110101 53
68 Manufacturer P/N 34 00110100 52
69 Manufacturer P/N 45 01000101 69
6A Manufacturer P/N 57 01010111 87
Manufacturer P/N (If <13 char, then
terminate with ASCII code 0Ah, set
6B remaining char = 20h) 31 00110001 49
6C Flag 00 00000000 0
6D Flag 00 00000000 0
6E Flag 00 00000000 0
6F Data Type Tag: FE 11111110 254
70 Flag 00 00000000 0
71 SMBUS Value 30 00110000 48
72 SMBUS Value 41 01000001 65
73 SMBUS Value 4D 01001101 77
Timing Descripter #4

74 SMBUS Value 57 01010111 87


75 SMBUS Value 78 01111000 120
76 SMBUS Value A4 10100100 164
77 SMBUS Value CC 11001100 204
SMBUS Value = max nits (Typically
78 = 00h) F8 11111000 248
Number of LVDS receiver chips = ‘01’
79 or ‘02’ 01 00000001 1
7A BIST Enable: Yes = ‘01’ No = ‘00’ www.DataSheet.co.kr

01 00000001 1
(If <13 char, then terminate with ASCII
7B code 0Ah, set remaining char = 20h) 0A 00001010 10
(If <13 char, then terminate with ASCII
7C code 0Ah, set remaining char = 20h) 20 00100000 32
(If <13 char, then terminate with ASCII
7D code 0Ah, set remaining char = 20h) 20 00100000 32
Extension flag (# of optional 128
Checksum

EDID extension blocks to follow, Typ =


7E 0) 00 00000000 0
Checksum (The 1-byte sum of all 128
7F bytes in this EDID block shall = 0) E9 11101001 233

Document version 0.1 36/37

Datasheet pdf - http://www.DataSheet4U.net/


www.DataSheet.co.kr

Document version 0.1 37/37

Datasheet pdf - http://www.DataSheet4U.net/

You might also like