Scribd Logo
Upload

Welcome to Scribd!

  • 212 views

    Service Bulletin - SB 08-007: Avionics

    Uploaded by

    zach
    This service bulletin from S-TEC Corporation provides instructions for replacing the universal joint in their 01260 Turn Coordinator/Roll Computer. It affects units with part number 01260-( )-( )-( ). The bulletin gives the necessary tool, part number 61227 coupling, and step-by-step instructions to remove the old universal joint and install the new one. FAA approval is not needed for this replacement.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Service Bulletin - SB 08-007: Avionics

    Uploaded by

    zach
    212 views5 pages
    This service bulletin from S-TEC Corporation provides instructions for replacing the universal joint in their 01260 Turn Coordinator/Roll Computer. It affects units with part number 01260-( )-( )-( ). The bulletin gives the necessary tool, part number 61227 coupling, and step-by-step instructions to remove the old universal joint and install the new one. FAA approval is not needed for this replacement.

    Original Title

    SB 08-007

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This service bulletin from S-TEC Corporation provides instructions for replacing the universal joint in their 01260 Turn Coordinator/Roll Computer. It affects units with part number 01260-( )-( )-( ). The bulletin gives the necessary tool, part number 61227 coupling, and step-by-step instructions to remove the old universal joint and install the new one. FAA approval is not needed for this replacement.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    212 views5 pages

    Service Bulletin - SB 08-007: Avionics

    Uploaded by

    zach
    This service bulletin from S-TEC Corporation provides instructions for replacing the universal joint in their 01260 Turn Coordinator/Roll Computer. It affects units with part number 01260-( )-( )-( ). The bulletin gives the necessary tool, part number 61227 coupling, and step-by-step instructions to remove the old universal joint and install the new one. FAA approval is not needed for this replacement.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 5

    Avionics

    S-TEC Corporation
    One S-TEC Way
    Mineral Wells, TX 76067
    www.cobham.com
    www.s-tec.com

    SERVICE BULLETIN – SB 08-007


    PN: 7782
    DATE: 08-06-08
    TO: S-TEC Dealers
    FROM: Tim Ballard, Vice President of Engineering

    1. PLANNING INFORMATION
    A. EFFECTIVITY
    Turn Coordinator/Roll Computer part number 01260-( )-( )-( ).
    B. CONCURRENT REQUIREMENTS
    N/A
    C. REASON
    Provide manufacturer’s technical data for field replacement of the universal joint in the 01260 Turn Coordinator/Roll Computer.
    D. DESCRIPTION
    N/A
    E. COMPLIANCE
    N/A
    F. APPROVAL
    FAA and TSO approval is not affected.
    G. MANPOWER
    Up to one hour of labor will be reimbursed for units under warranty.
    H. WEIGHT AND BALANCE
    N/A
    I. ELECTRICAL LOAD DATA
    N/A
    J. REFERENCES
    Pilot Operating Handbook (POH), SYS 20/30/30 ALT, part number 8777.
    Guide, troubleshooting for: System 20, 30, 30 ALT, part number 87256.
    K. OTHER PUBLICATIONS EFFECTED
    N/A

    SB 08-007

    FRM 8.3-02-01 Rev. E


    2. MATERIAL INFORMATION
    A. TOOLING
    N/A
    B. MATERIAL
    1. Coupling, double jointed, S-TEC part number 61227.
    3. ACCOMPLISHMENT INSTRUCTIONS
    A. DISASSEMBLY INSTRUCTIONS (Refer to Figure1)
    Note: All ESD precautions shall be observed.
    1. Remove six screws (1) securing cover (2) to chassis.
    2. Remove two screws (3) securing cover (2) to chassis.
    3. Slide cover (2) off of chassis.
    4. Loosen set screws on universal joint and remove from switch assembly.
    B. RE-ASSEMBLY INSTRUCTIONS
    1. Install new universal joint.

    SB 08-007 2

    FRM 8.3-02-01 Rev. E


    SB 08-007 3

    FRM 8.3-02-01 Rev. E


    Figure 1
    SB 08-007 5

    FRM 8.3-02-01 Rev. E

    You might also like