Metrology Terminology Calibration Verification Validation

Metrology Terminology:
Calibration, Verification, Validation

We are often asked about the difference between calibration, verification, and
validation. While they may seem similar, it is critical that you use the correct process or
processes to ensure that your quality system meets all the necessary requirements.
Calibration
Calibration is the process of comparing an unknown quantity or value to a known quantity.
A trained calibration technician will check the instrument at several points through its
range and may make adjustments to bring the instrument into alignment with the standard
if it is found to be out of tolerance.
All calibrations should be done using a traceable standard. Traceability means that the
value of the standard can be directly traced back through an unbroken chain of
comparisons to a national standard. These standards are coordinated by national
metrological institutions, such as the National Institute of Standards and Technology
(NIST).
Two levels of calibration that we offer at J.A. King are NIST Traceable and ISO 17025
Accredited. A NIST Traceable calibration is just that, a calibration that uses standards
which can be traced back to NIST. An ISO 17025 calibration takes this a step
further. When a laboratory says that they are an ISO 17025 Accredited laboratory, or that
a calibration is ISO 17025 Accredited, it means that an accrediting body such as The
American Association for Laboratory Accreditation (A2LA) has signed off on that lab’s
procedures for calibrating specific equipment types within an approved range. All of the
procedures that a lab has been signed off through an accrediting body are listed on their
scope of accreditation.
Verification
Verification is a process that is done periodically to ensure an instrument is working as it
should be and that any error in its measurement is still within tolerance for the
application. Unlike calibration, this process does not involve making any type of
adjustments. More importantly, verification may not require comparison against a NIST
traceable master standard, it is simply a check against another piece of equipment to
ensure the instrument is still working as intended.
For example, you may have a verification weight that you put on your balance each day
to ensure it is reading correctly before using the balance. This isn’t a calibration, mainly
because you aren’t checking the equipment over the entire range and because you aren’t
making any adjustments to the equipment. Instead, you are simply ensuring that the
instrument is working as intended.
Validation
Metrology Terminology:
Calibration, Verification, Validation
Validation is particularly important in the life sciences industry, but has applications in
other industries as well. Validation is the process of ensuring that all parts of a system
are working together correctly to produce the desired outcome. A simple example is oven
validation. You can calibrate and verify separate components such as temperature
controllers, temperature monitors, and heating elements, but these components all work
together in a system. This means you still need to confirm that the system functions
correctly as a whole, ensuring that the oven is heating evenly throughout, at the desired
temperature for the correct duration of time.
In any industry, specific procedures are written for validation protocols to ensure that the
proper steps are taken and documented. In the life sciences industry, validation protocols
are more formalized due to FDA requirements. These validation protocols know as
IQ/OQ/PQ will include test parameters, product characteristics, production equipment,
and decision points on what constitutes acceptable test results.
What is IQ/OQ/PQ? Installation Qualification (IQ), Operational Qualification (OQ), and

Performance Qualification (PQ) protocols are critical in equipment validation for quality
assurance.
 Installation Qualification protocols check that all parts of the system have been delivered
and installed correctly. This also includes making sure that environmental conditions and
services meet manufacturer specifications.
 Operational Qualification protocols ensure that the equipment performs as it should to
meet the requirements of the application. During this phase, unit operation as well as all
controls and alarms are individually tested and their operations documented.
 Performance Qualification protocols confirm and document that the entire system is
performing as it should to produce the desired results. For a chamber or oven, testing
would be performed loaded with product or a product surrogate.

Metrology Terminology Calibration Verification Validation

Uploaded by

Copyright:

Available Formats

Metrology Terminology Calibration Verification Validation

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Metrology Terminology Calibration Verification Validation

Uploaded by

Copyright:

Available Formats

Metrology Terminology:

Calibration, Verification, Validation

What is IQ/OQ/PQ? Installation Qualification (IQ), Operational Qualification (OQ), and

You might also like